INSTALLATION & OPERATING
INSTRUCTIONS
for
REDCO® INSTABLEND™
MODEL 16900 SERIES
TO BE SERVICED ONLY BY AUTHORIZED PERSONS
Instablendopsman
REV: 4/10/07
Part Number: 2810255
MODELS
This manual describes the operation and maintenance of the 16900, 16901, 16902, 16903 and 16904 portable
liquidizers, mixers and liquidizer/mixers.
The model reference and its specifications are shown on the identification plate located on the front of the unit.
The InstaBlend has been designed and manufactured in accordance with the following standards:
Standards for machine safety: UL 1097, UL 763, UL 94
Standards for Hygiene and Food equipment materials: ANSI-NSF 8 and ANSI-NSF 51.
UTILITY SPECIFICATION
REDCO® INSTABLEND™
Specifications
Liquidizer Arm Length
Mixer Arm Length
Total Length
16900
15”
-
16901
21”
-
16902
15”
16903
-
16904
10.5”
-
15.5”
27.5”
15.5”
28”
29”
35”
21.5”
Electrical Supply
Constant Speed (RPM)
Range (RPM)
120V / 50Hz / 60Hz / 1 Phase
14000
15000
14500
14500
4.2 lbs.
1000-11000
7.4 / 7.7 lbs.
1000-11000
7.7 lbs.
Weight
7.4 lbs.
9.1 lbs.
INSTALLATION
For best results and a long service life, follow the instructions given in this manual.
POSITIONING
The InstaBlend is not permanently fixed in one location. It can be carried to the required location/area for use
where there is a suitable wall receptacle. Each unit is supplied with a wall for convenient storage.
InstaBlend - 16000 Series Ops Manual
3
OPERATION
Plug the appliance into a proper electrical outlet.
MODELS 16900, 16901, 16902, 16903
STARTING
Pressing the “Start” button (B) together with the
“Safety” button (D) will cause the machine to
start. The machine will not start if the “Safety”
button is not actuated. Releasing the “Start”
button will cause the machine to stop operating.
CONTINUOUS OPERATION
For continuous operation, while the machine is
running, press the “Lock” button (C). After the
“Lock” button is depressed, the “Start” button
may be released and the machine will continue to
operate. Pressing the “Start” button again will
shut off the machine.
Models 16902 and 16903 – The Speed Control
(A) may be adjusted to change the speed of the
blade or mixer.
MODEL 16904
STARTING
Pressing the “Start” button (1) together with the
“Safety” button (2) will cause the machine to
start. The machine will not start if the “Safety”
button is not actuated. After the machine has
started, the “Safety” button may be released and
the machine will continue to operate. Releasing
the “Start” button will cause the machine to shut
off.
BEST RESULTS
Best results are achieved by introducing the arm of the machine into the bowl, up to 2/3 of the arm’s length.
For optimum operation, it is better if the foot of the machine does not touch the bottom of the bowl.
In order to prevent splashed food from getting inside the motor unit, it is recommended not to incline the appliance
more than 30°.
4
InstaBlend - 16000 Series Ops Manual
MAINTENANCE
WARNING
!
!
TO AVOID ELECTRICAL SHOCK THAT CAN CAUSE SEVERE INJURY OR DEATH, ALWAYS UNPLUG
LIQUIDIZER / MIXER BEFORE PROCEEDING WITH ANY CLEANING OR MAINTENANCE PROCEDURES!
IN ORDER TO AVOID DAMAGE TO PEOPLE AND THE APPLIANCE, READ AND FOLLOW THE
MANUFACTURER’S INSTRUCTIONS FOR THE CLEANING OF THE LIQUIDIZER / MIXER.
DO NOT USE THE FOLLOWING PRODUCTS:
• Abrasive cleaners such as Ammonia, Lye, etc.
• Solvents
• Metal Scourers
• Gritty Detergents
These products would score, scratch and damage the metallic and plastic surfaces of the appliance.
CLEANING PROCEDURE
All parts of the machine that come into contact with the food product should be cleaned immediately after each use.
Place up to 2/3 of the length of the mixer arm into hot water (95°F to 115°F) and switch on for a few seconds. The
mixer and blade must be cleaned with hot water and a mild detergent, leaving the blade with warm water to remove
any residue. Allow the mixer arm and blade to air dry.
The motor set must be cleaned with a damp cloth. Under no circumstances must water enter the motor set. If
water accidentally enters the motor set, dry the motor set carefully before switching on the machine.
After cleaning, place the machine in its wall support.
Models 16900, 16901, 16902, 16903:
The Liquidizer/Mixer arm may be removed for cleaning. To remove the Liquidizer/Mixer arm, turn the
Liquidizer/Mixer clockwise until the arm separates from the motor set. To reassemble, reverse the procedure.
InstaBlend - 16000 Series Ops Manual
5
ADDITIONAL INFORMATION
In the event the power supply cord becomes damaged and has to be replaced, the repair
may only be completed by a Lincoln Authorized Service Agency. Information on Authorized
Service Agencies maybe obtained by calling Lincoln Technical Support at (800) 678-9511.
DO NOT USE THE MACHINE IF THE POWER SUPPLY CORD IS DAMAGED.
WARNING:
!
In order to prevent injury or damage to the InstaBlend, never put utensils or hands into the
mixture.
WARNING:
WARNING:
!
!
The blade edges are sharp and care should be exercised when cleaning.
The airborne noise emitted by the appliance, as measured on a type appliance at a distance of one (1) meter is
less than 80dB(A).
WARNING – SHOCK HAZARD: To reduce the risk of injury or death by electric shock:
!
1. Do not place or store where Liquidizer/Mixer can fall or be knocked into water or other liquid mixture.
2. If Liquidizer/Mixer falls into water or other liquid mixture, unplug immediately.
Do not reach into water or liquid mixture to retrieve.
3. Do not allow water or other liquid mixture to enter the motor housing slots when using or cleaning.
4. Switch power “OFF” and disconnect from power source before cleaning and when not in use.
WARNING – SHARP OBJECTS: Machine uses sharp, rapidly moving mixing blades.
To reduce the risk of injury:
!
1. Immerse mixing blades before turning on the Liquidizer/Mixer.
2. Turn “OFF” Liquidizer/Mixer before removing blades from mixture.
3. Avoid contact with moving blades.
6
InstaBlend - 16000 Series Ops Manual
This page intentionally left blank.
InstaBlend - 16000 Series Ops Manual
7
PARTS LIST
MODELS 16900, 16901, 16902, 16903
Number
1A
1B
2
Description
Variable Speed Control
Speed Control
Hood Set
Spare Part #
380067
380066
380069
380071
380077
370075
380057
380079
380060
380070
380064
380074
380072
380073
380055
380058
380061
380054
380080
380056
380062
380059
380063
380068
380065
380076
380078
16900
16901
16902
16903
√
√
√
√
√
√
√
√
√
√
3A
3B
4
Motor Frame Set
Motor Frame Set
Reducing Frame Set
Blade Lower Locking Set
Whisks Shaft Set
Brush Set
√
√
√
√
√
√
√
√
5
√
√
√
√
√
√
√
6
7A
7B
8
Brush Set
√
√
√
√
√
√
Control Protectors Set
Motor Set
9A
9B
9C
10
Motor Set
Motor Set
√
√
Bearings – Grommet Set
Blade Set
√
√
√
√
√
11A
11B
12
Blade Set
√
√
Arm Coupling Nut Set
Whisks Set
√
√
√
√
√
√
√
√
13
14A
14B
15A
15B
16
Arm Shaft
Arm Shaft
√
Turbine Protector
Turbine Protector
Power Cord
√
√
√
√
√
√
√
√
√
√
√
√
√
√
17
Coupling Set
18
Reducer Shaft
Wall Support
19
√
√
√
√
√
Turbine Lock Key
(blade removal tool)
20
21
380084
√
√
Liquid Arm Assembly – 21”
Liquid Arm Assembly – 15”
380081
380082
380083
√
√
√
Not Shown Mixer Arm Assembly
√
8
InstaBlend - 16000 Series Ops Manual
PARTS DIAGRAM
MODELS 16900, 16901, 16902, 16903
InstaBlend - 16000 Series Ops Manual
9
PARTS LIST
MODEL 16904
Number
Description
Wall Support Set
Spare Part #
380052
380050
380041
380042
380040
380045
380047
380053
380043
380048
380049
380046
380044
380051
16904
1
2
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Switch, 2-Pole
Blade Set
3
4
Coupling Set
5
Lower Hood Set
Bearings-Grommets Set
Motor Set
6
7
8
Power Cord
9
Frames Set
10
11
12
13
14
Protectors and Screws Set
Shaft
Brush Set
Grinder Arm Set
Turbine Protector
10
InstaBlend - 16000 Series Ops Manual
PARTS DIAGRAM
MODELS 16904
InstaBlend - 16000 Series Ops Manual
11
SCHEMATIC DIAGRAMS
MODELS 16000, 16901
12
InstaBlend - 16000 Series Ops Manual
SCHEMATIC DIAGRAMS (CONT’D)
MODELS 16902, 16903
InstaBlend - 16000 Series Ops Manual
13
SCHEMATIC DIAGRAMS (CONT’D)
MODEL 16904
14
InstaBlend - 16000 Series Ops Manual
This page intentionally left blank.
InstaBlend - 16000 Series Ops Manual
15
Lincoln Foodservice Product, LLC
1111 North Hadley Road
Fort Wayne, Indiana 46804
United States of America
Telephone: (260) 459-8200
U.S. Fax: (888) 790-8193
Int’l Fax: (260) 436-0735
Technical Support Hotline: (800) 678-9511
|