CD-RECEIVER
KDC-6080R
KDC-6080RV
KDC-5080R
INSTRUCTION MANUAL
COMPACT
DIGITAL AUDIO
B64-1627-00 (EN)
Safety precautions
IMPORTANT INFORMATION
2WARNING
2CAUTION
You cannot connect the unit directly to the
following CD automatic changers. For users
who want to use older changers with the
unit, follow the directions below according to
the type of changer you own:
To prevent injury and/or fire, take the
following precautions:
• Insert the unit all the way until it is fully
locked in place. Otherwise it may fly out of
place during collisions and other jolts.
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• KDC-C200 / KDC-C300 / KDC-C400
• Do not open the top or bottom covers of the
unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
• To prevent short circuits when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• During installation, do not use any screws
except for the ones provided. The use of
improper screws might result in damage to
the main unit.
• Do not apply excessive force to the moving
faceplate. Doing so will cause damage or
malfunction.
Use the extension cable and the control box
attached to the CD changer, and the optional
CA-DS100 converter cable.
• KDC-C301 / KDC-C600 / KDC-C800 / KDC-
C601 / KDC-C401
Use the extension cable attached to the CD
changer, and the optional CA-DS100
converter cable.
• KDC-C100 / KDC-C302 / C205 / C705 /
non-Kenwood CD changers
• When extending the ignition, battery or
ground cables, make sure to use automotive-
grade cables or other cables with an area of
2
0.75mm (AWG18) or more to prevent cable
deterioration and damage to the cable
coating.
• To prevent short circuits, never put or leave
any metallic objects (e.g., coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it to
strong shock.
The unit may break or crack because it
contains glass parts.
• Do not touch the liquid crystal fluid if the
LCD is damaged or broken due to shock. The
liquid crystal fluid may be dangerous to your
health or even fatal.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
Cannot be used with this model.
2CAUTION
You can damage both your unit and
the CD changer if you connect them
incorrectly.
2CAUTION
Do Not Load 8-cm (3-in.) CDs in the
CD slot
If you try to load an 8-cm CD with its adapter
into the unit, the adapter might separate
from the CD and damage the unit.
• Do not apply excessive force to the open
faceplate or place objects on it. Doing so will
cause damage or breakdown.
— 3 —
Safety precautions
• The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
NOTE
• If you experience problems during
installation, consult your Kenwood dealer.
• Press the reset button if the CD auto
changer is first controlled and operates
incorrectly. The original operating condition
will return.
Egnlish
• The functions that can be used and the
information that can be displayed will differ
depending on the external disc players being
connected.
PWR
OFF
DISC
PTY
DAB
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
TI
VOL ADJ
DISP
NAME.S
LOUD
DISC
Reset button
• Characters in the LCD may become difficult
to read in temperatures below 41 ˚F (5 ˚C).
— 4 —
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
Cleaning the Unit
If the front panel gets dirty, turn off the
power and wipe the panel with a dry silicon
cloth or soft cloth.
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It
means that the unit is utilizing laser beams
that are of a weaker class. There is no
danger of hazardous radiation outside the
unit.
2CAUTION
Do not wipe the panel with a stiff cloth or a
cloth dampened by volatile solvents such as
paint thinner and alcohol. They can scratch
the surface of the panel and/or cause the
indicator letters to peel off.
Lens Fogging
Cleaning the CD Slot
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a whilst,
consult your Kenwood dealer.
As dust can accumulate in the CD slot, clean
it occasionally. Your CDs can get scratched if
you put them in a dusty CD slot.
— 5 —
Handling Compact discs
Playing a CD that is dirty, scratched
or warped can cause the sound to
skip and the unit to operate
incorrectly, resulting in worsened
sound quality. Take the following
precautions to prevent your CDs from
getting scratched or damaged.
Cleaning CDs
Do Not Load CD Accessories in Slot
If a CD has become dirty, wipe it off gently
using a commercially available cleaning cloth
or a soft cotton cloth, starting from the
centre of the disc and moving outward. Do
not clean CDs with conventional record
cleaners, anti- static formulas, or chemicals
such as paint thinner or benzene.
Do not use commercially available CD
accessories that can be loaded into the CD
slot, such as stabilisers, protective sheets,
or CD cleaning discs, since they can cause
the unit to malfunction.
Egnlish
Removing the CD
Only remove the CD from the machine in a
horizontal direction. You may damage the
surface of the CD if you try pulling it down
as it ejects.
Handling CDs
• Do not touch the recorded side of the CD
(i.e., the side opposite the label) when
holding it.
Checking New CDs for Burrs
When playing a new CD for the first time,
check that there are not any burrs stuck to
the perimeter of the disc or in the central
hole. CDs with burrs stuck on them may not
load properly or may skip whilst playing.
Remove burrs using a ballpoint pen or a
similar utensil.
Do Not Use Special Shape CDs
• Be sure to use round shape CDs only for
this unit and do not use any special shape
CDs. Use of special shape CDs may cause
the unit to malfunction.
• Do not stick tape on either side of the CD.
Tape
Burrs
Storing CDs
COMPACT
• Do not store CDs in areas exposed to direct
sunlight – such as a car seat or above the
fascia panel (dashboard) – or other hot
places.
• Remove CDs from the unit when not
listening to them for a whilst, and put them
back in their cases. Do not stack CDs that
have been removed from their cases or prop
them against something.
DIGITAL AUDIO
• Be sure to use CDs with disc mark
Burrs
only for this unit.
Do Not Use CDs with Sticker on the
Labelled Side
Do not use the CD with the label sticker
stuck on it.
Using such a CD may cause the CD to be
deformed and the sticker to peel off,
resulting in malfunction of the unit.
— 6 —
General features
SRC /
PWR OFF
Power
¢
u
4
FM
d
Turning on the power:
Press the SRC button.
PWR
OFF
NOTE
DISC
PTY
DAB
Turn the power on before carrying out the following procedures.
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
TI
VOL ADJ
DISP
NAME.S
LOUD
Turning off the power:
DISC
Hold down the PWR OFF button for one second or more.
AM
AUD
ATT / LOUD
#1 - 5
Release button
Volume
KDC-6080R/KDC-6080RV
Increasing Volume:
ATT indicator
Press the u button to turn up the volume.
Decreasing Volume:
Press the d button to turn down the volume.
Attenuator
This function allows you to turn down the volume quickly.
LOUD indicator
Turning Attenuator On/Off:
Press the ATT button to switch the attenuator on and off.
When the attenuator is on, the ATT indicator blinks.
When the attenuator is off, the volume returns to the original
level.
KDC-5080R
ATT indicator
NOTE
Turning the volume up, or turning it all the way down deactivates
the attenuator function.
LOUD indicator
— 7 —
General features
Switching Modes
Loudness
This function amplifies low and high tones when the volume is
Switching Modes:
turned down.
Each time you press the SRC button, the mode switches as
follows:
The LOUD indicator lights up, when the loudness function is
on.
Egnlish
▼
Turning Loudness On/Off:
Tuner mode
▼
Hold down the LOUD button for one second or more to switch
the loudness on and off.
CD mode
▼
External disc control mode 1
▼
External disc control mode 2/AUX mode
Audio Control Setting
▼
Adjust various parameters of sound quality.
Standby mode
1
2
Press the AUD button to enter the control mode.
Selecting the standby mode:
Selecting mode
Press the SRC button repeatedly to select to "ALL OFF" .
When "ALL OFF" is displayed, the standby mode is turned on.
The standby mode turns all functions off although leaving the
unit’s power on. Use this mode when you want to have the
display illuminated but do not want to listen to anything.
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
Please refer to the following for the contents of the
adjustment modes.
NOTE
NOTE
Source tone memory
• The mode switches to the next mode from any mode which
cannot be used.
• The external disc control mode will differ depending on the unit
that is connected.
• The AUX mode is available only when the changer / AUX
switching adapter (KCA-S210A or CA-C1AX) or CD changer
(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is
connected to this unit.
During the AUX mode, "AUX" / AUX-name will show in the
display. When the CA-C1AX is being used, the AUX Mode will
replace the External Disc Control Mode.
Each source (tape, CD, MD, FM, AM, and disc changer) has its
own memory in which to store the bass and treble tone settings.
The settings made for a particular source are then recalled
automatically whenever you use that source (e.g., FM mode uses
the tone settings made for FM, AM for AM, etc.).
3
Adjust each mode
Press the 4/¢ button.
Please refer to the following for the adjusting values.
4
Press the AUD button to end the control mode.
NOTE
Presetting AUX-name
In the AUX mode, press the NAME.S button for two seconds or
more. "NAME SET" is display and AUX-name mode is entered.
Input the characters, referring to the section on "Presetting Disc
Names (DNPS)" (page22).
"Kex"/"ec"/"dB" : Recalling the kenwood preset sound setting
Press the preset buttons (#1-6).
Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy,
#6;Scan of #1-5
— 8 —
NOTE
1
Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
• This mode is available only when the Sound coordinate system
is on. (page29)
• You can call the following settings with this function; bass
centre frequency, bass level, bass quality factor, bass
extension, treble centre frequency, and treble level setting.
Their setting values are different depending on the setting of
the mobile preset plan mode.
2
3
Press the AUD button to enter the mobile preset plan mode.
Press either the 4 or ¢ button to select the type of
speaker. The setting switches as follows.
Off / For the OEM speaker / For 6/6x9 in. speaker /
For 5/4 in. speaker
4
Press the AUD button to end the mobile preset plan mode.
NOTE
"Bass"/"BAS" : Adjust the bass level.
Setting values: - 8 – + 8
• When you change the setting of type of speaker, the bass and
treble tone settings are returned to original levels.
• This mode is available only when the Sound coordinate system
is on. (page29)
"Treble"/"TRE" : Adjust the treble level.
Setting values: - 8 – + 8
TEL Mute
"Balance"/"BAL" : Adjust the balance level.
Shut down the audio system temporarily whenever an
incoming call is received.
Setting values: Left 15 – Right 15
NOTE
"Fader"/"FAD" : Adjust the fader level.
The function will not work if a cable is not connected to the car
phone.
Setting values: Front 15 – Rear 15
When the telephone rings:
When a call is received, "CALL" is displayed and all the unit
functions are temporarily interrupted.
"V OFFSET/VOS" : Set the sound level of the each source
selected by adjusting the level difference
between the basic sound level and the
required level.
Restoring Original Unit Source During Phone Call:
Press the SRC button.
"CALL" disappears from the display, and the volume of the
original source is restored gradually.
Setting values: - 8 –
0
Turning TEL Mute Function Off After Phone Call:
Hang the phone up.
"CALL" disappears from the display.
The original source (i.e., the one used before the phone call) is
returned to automatically, and the volume restored gradually.
Mobile Preset
This function allows you to adjust the setting that is recalled
with the sound coordinate system, according to types of
speakers.
— 9 —
General features
Theft Deterrent Faceplate
The faceplate can be reversed to hide the control panel or
detached form the unit, helping to deter theft.
Egnlish
Removing the Faceplate:
1
• When the control panel is visible
Press the release button.
2CAUTION
• When the control panel has been hidden
Press the upper side of the faceplate.
Do not set the right side of the faceplate in the faceplate bracket
first, when reattaching the faceplate. Doing so may cause the
connector on the faceplate bracket to malfunction.
2
Holding the centre part of the faceplate, pull it out.
2
Press the right side of the faceplate until it locks.
Hiding the control panel:
1
2
Press the release button and slide open the faceplate.
Push upward the back of the control panel and reverse the
panel.
3
Push back the bottom of the faceplate bracket until it locks.
2CAUTION
• Do not apply excessive force to the faceplate bracket without
attaching the faceplate. Doing so will cause the faceplate
bracket to be deformed.
• Do not touch the connector on the faceplate bracket after
removing the faceplate. Touching the connector may cause
damage to the unit.
NOTE
The panel cannot be reversed when the faceplate is not attached.
• Do not touch two metal parts on both sides of the faceplate
bracket. Touching those parts may injure you.
Opening the control panel:
1
Press the upper side of the faceplate.
The faceplate will open.
NOTE
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate
in its special storage case whilst detached.
2
Push the bottom of the control panel and close the faceplate.
• Do not expose the faceplate or its storage case to direct
sunlight or excessive heat or humidity. Also avoid places with
too much dust or the possibility of water splashing.
Reattaching the Faceplate:
1
Hold the faceplate so that the control panel faces the front
toward you and set the left side of the faceplate in the
faceplate bracket.
— 10 —
Tuner features
SRC /
PWR OFF
NOTE
4
¢
FM
The buttons do not work when the control panel is slided.
PWR
OFF
DISC
PTY
DAB
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
TI
VOL ADJ
DISP
NAME.S
LOUD
DISC
DISP AM
#1~6
KDC-6080R/KDC-6080RV
£ indicator
Frequency
Band display
ST indicator
Preset station number
Preset station number
AUTO indicator
KDC-5080R
Band display
Frequency
ST indicator
£ indicator
AUTO indicator
— 11 —
Tuner features
Tuning
1
2
Select the band/ station that you want to have stored.
1
Hold down the button (#1-6) that you want to use for the
station, for two seconds or more.
The button number blinks once in the display to indicate that
the data has been stored.
Press the SRC button repeatedly until the tuner mode is
obtained. "TUNER" is displayed only when the tuner mode is
selected.
Egnlish
2
3
Press either the FM or AM button to select the band.
Each time you press the FM button, the band switches
between the FM1, FM2 and FM3.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Press the AM button to select the MW and LW bands.
NOTE
• Auto Seek Tuning
You can store 6 stations in each of the FM1, FM2, FM3, and AM
(MW and LW) bands.
Press the ¢ button to seek increasing frequencies.
Press the 4 button to seek decreasing frequencies.
• Preset station seek tuning
Press the ¢ button to move to the next preset station (i.e.,
the one with the next highest number), and the 4 button to
move to the last preset station (i.e., the one with the next
lowest number).
Switching Display for Tuner
You can change the display used when listening to the radio.
NOTE
If the frequencies stored at the preset numbers receive
stations which were not originally memorized when traveling
long distances, the preset number is not displayed. In such
cases, pressing the 4/¢ button to use preset station
seek will receive channel 1.
Switching the Display:
Pressing the DISP button switches the display as follows.
Select the Radio Text Display mode.
Programme Service name
• Manual Tuning
Press the ¢ button to increase the frequency by one step.
Radio text
Clock
Press the 4 button to decrease the frequency by one step.
NOTE
• The ST indicator lights up when stereo broadcasts are being
Date
received.
• Please see the menu settings about selecting tuning mode.
(page30)
Displaying Frequencies:
Hold down the DISP button for one second or more.
The frequency for the RDS station will be displayed for five
seconds instead of the station name.
NOTE
Station Preset Memory
• If the RDS station currently tuned to is transmitting no text
whilst the Radio Text Display mode is turned on, "NO TEXT" will
appear in the display. Whilst awaiting reception, "WAITING" will
be displayed.
Store the frequency of the station currently being listened to.
You can then recall that station with a single touch of a button.
— 12 —
RDS features
• The £ indicator lights whilst the clock is displayed.
4
¢
FM
PTY
2WARNING
To prevent accidents, drivers should not look at the display whilst
on the road.
PWR
OFF
DISC
PTY
DAB
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
TI
VOL ADJ
DISP
NAME.S
LOUD
DISC
TI/VOL ADJ
DISP AM
#1 - 6
KDC-6080R/KDC-6080RV
PTY indicator TI indicator
™ indicator
KDC-5080R
PTY indicator
™ indicator
TI indicator
— 13 —
RDS features
RDS (Radio Data System)
Traffic Information Function
You can listen to traffic information. If you are listening to
tapes or discs, they will continue playing until a traffic bulletin
is broadcast.
RDS is a digital information system that lets you receive
signals besides those of regular radio programmes, such as
network information being transmitted from radio stations.
When listening to an RDS station (ie, a station with RDS
capability), the programme service name of the station is
displayed along with the frequency, advising you quickly which
station is being received.
RDS (Radio Data System) stations also transmit frequency data
for the same station. When you are making long trips, this
function automatically switches to the particular frequency
with the best reception for the particular network of stations
that you want to listen to. The data is automatically stored,
allowing you to switch quickly to another RDS stations,
broadcasting the same programme, that has better reception.
These include stations stored in the station preset memory that
you often listen to.
Egnlish
Turning TI function On/Off:
Press the TI button to turn the function on and off.
When the function is on, the TI indicator is turned on.
When none is being received, the TI indicator will blink on and
off. When a traffic information station is being received, the TI
indicator will turn on.
When a traffic bulletin begins to be broadcast, "TRAFFIC" will
be displayed, and reception will begin at the preset volume.
If you are listening to a tape or disc when a traffic bulletin
begins, they will automatically be turned off. When the bulletin
ends or poor reception is experienced, the tape or disc will
begin playing again.
NOTE
Pressing the TI button whilst in the MW/LW band automatically
switches reception to the FM band. However, the MW/LW band
is not returned to when the TI button is pressed again.
Enhanced Other Network
Stations that offer <Enhanced Other Network> also transmit
information about other RDS stations that have traffic
information. When you are tuned to a station that is not
transmitting traffic information, but another RDS station starts
transmitting a traffic bulletin, the tuner automatically switches
to the other station for the duration of the bulletin.
Switching to a Different Traffic Information Station:
Use the 4 / ¢ buttons to make an auto seek of the TI
stations in a certain band.
NOTE
• When you are listening to a tape or disc, you cannot change to
another TI station.
• When the auto TP seek function is turned on and reception
starts to weaken, the tuner automatically seeks traffic
information stations with better reception.
• If you are tuned to a station that is not a traffic information
station itself but which provides <Enhanced Other Network>
services, you can still have traffic information received.
• Holding the TI button down for one second or more when the
TI function is on in the disc control mode results in a change to
the frequency display of the traffic information station for five
seconds.
Alarm
When an emergency transmission (announcing disasters, etc.)
is sent, all current functions are interrupted to allow the
warning to be received.
— 14 —
Please see the menu settings (page32) about switching between
manual scrolling and automatic scrolling.
Presetting Volume for Traffic Information/News
Preset the volume level to be used for traffic information and
news broadcasts.
1
2
3
Tune into the station for which you want to set the volume.
Adjust the volume to the desired level.
Hold down the TI VOL ADJ button for two seconds or more.
The volume level blinks once in the display to indicate that the
data has been stored.
Future traffic information/news broadcasts are heard at the
preset level.
NOTE
• The volume cannot be lowered by this function during tuner
reception. The volume is only set when it is louder than the
listening volume of the tuner.
• You can arrange only to listen to traffic information or news
bulletins with at preset volume with the volume set at
minimum.
Radio Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
To scroll manually:
1
2
Press the DISP button to display the Radio Text.
Holding down the DISP button for one second or more results
in one scrolling display of the text.
To scroll automatically:
1
Press the DISP button to display the Radio Text.
The text will be displayed in one scrolling display.
2
Holding down the DISP button for one second or more results
in one scrolling display of the text.
NOTE
— 15 —
RDS features
16. Weather
17. Finance
(Weather)
(Finance)
(WEATHER)
(FINANCE)
(CHILDREN)
(SOCIAL A)
(RELIGION)
(PHONE IN)
(TRAVEL)
Programme Type (PTY) Function
Conduct auto seek tuning only on those stations with selected
kinds of programmes.
18. Children’s programmes (Children)
19. Social Affairs
20. Religion
(Social A)
(Religion)
(Phone In)
(Travel)
(Leisure)
(Jazz)
(Country)
(Nation M)
(Oldies)
(Folk M)
(Document)
Egnlish
1
Press the 38(PTY) button.
21. Phone In
"PTY" is displayed, and the Programme Type Selection (PTY)
Mode entered.
22. Travel
23. Leisure
(LEISURE)
(JAZZ)
If you make no key input in 30 seconds, the mode will
automatically turn off.
24. Jazz Music
25. Country Music
26. National Music
27. Oldies Music
28. Folk Music
29. Documentary
(COUNTRY)
(NATION M)
(OLDIES)
(FOLK M)
(DOCUMENT)
NOTE
You cannot use this function whilst the traffic bulletin is received.
NOTE
Changing the Display Language to French, German, or Swedish
In the PTY mode, press the DISP button to display the name of
(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)
• You can select the type of programme directly by pressing a
preset button. The buttons are factory-set to the following
type of programmes:
the language currently used.
If you want to change the language, press the preset button for
the desired language and then the DISP button.
English is #1, French is #2, German is #3, and Swedish is #4 .
1. Music
4. Other Music
2. Speech
5. Serious Classical
3. News
6. Varied
2
Select the type of programme to be received
• Press either the FM or AM buttons repeatedly until the type
of programme you want to listen to.
NOTE
Changing the Preset Button Settings for Programme Type
After selecting the type of programme to be stored in a certain
preset button, press that button for at least two seconds.
The previously stored data for that button are erased and the
new programme type is stored.
The selection includes:
Programme type
Speech
KDC-6080R/RV
(Speech)
(Music)
KDC-5080R
(SPEECH)
(MUSIC)
Music
3
Seeking the selected programme type
1. News
(News)
(NEWS)
Press the 4 or ¢ button to make a seek of frequencies
2. Current Affairs
3. Information
4. Sports
(Affairs)
(Info)
(AFFAIRS)
(INFO)
(SPORT)
with your selected type of programme.
The display blinks and the seek starts.
(Sport)
"PTY" blinks in the display for about 30 seconds.
If you make no key input in 30 seconds, the PTY selection
mode will turn off automatically.
5. Education
6. Drama
(Educate)
(Drama)
(EDUCATE)
(DRAMA)
(CULTURE)
(SCIENCE)
(VARIED)
(POP M)
(ROCK M)
(EASY M)
(LIGHT M)
(CLASSICS)
(OTHER M)
7. Culture
(Culture)
(Science)
(Varied)
8. Science
9. Varied
NOTE
If no programme can be found, "NO PTY" is displayed.
If you want to select another type of programme, repeat steps 2
and 3 above.
10. Pop Music
11. Rock Music
(Pop M)
(Rock M)
12. Easy Listening Music (Easy M)
Switching to Other Stations with the Same Type of Programme:
When "PTY" is blinking in the display, perform auto seek
tuning.
13. Light Classical
14. Serious Classical
15. Other Music
(Light M)
(Classics)
(Other M)
— 16 —
CD/External disc control features
The tuner scans for another station with the same type of
programme.
SRC /
PWR OFF
4
¢
38
0
DISC+
Cancelling Programme Type Function During Its Operation:
Press the 38(PTY) button.
PWR
OFF
DISC
PTY
DAB
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
TI
VOL ADJ
DISP
NAME.S
LOUD
DISC
SCAN
REP
M.RDM
D.SCN
DISP DISC–
/NAME.S
RDM
Release button
KDC-6080R/KDC-6080RV
Track number
IN indicator
Disc number
Track time
KDC-5080R
Track time
Track number
IN indicator
Disc number
— 17 —
CD/External disc control features
■ When a unit equipped with an O-N switch is to be
connected, please also see the instruction manual of this
unit.
might scratch the CD.
Playing CDs Already Inserted:
Press the SRC button repeatedly until the CD mode is
obtained.
Set the O-N switch to "N". "N"-operation will be set.
Egnlish
"N"-operation:
"CD" is displayed when the CD mode has been selected.
The CD will start playing.
• The disc title and track title of the CD text can be displayed.
• The disc name will be displayed when the name has been
registered to any connected unit with the Presetting Disc
Names function, or when the playing unit contains a disc to
which the disc title has been recorded.
Pausing and Restarting CD Play:
Press the 38 button to make the disc pause.
Press the same button again to start play again.
Eject:
"O"-operation:
Press the release button and slide open the faceplate.
Press the 0 button.
• CD text cannot be displayed.
• Regardless of the control unit, the characters that can be
registered with the Presetting Disc Names function are "A~Z
0~9 /, +, –, ∗, =, <, >, [ , ]".
The CD stops playing and ejects from the slot.
Push back the bottom of the faceplate with your hand until it
locks.
• The disc name will be displayed when the name has been
registered to the playing unit with the Presetting Disc Names
function.
2CAUTION
• Do not attempt to insert a CD into the slot if another one is
already there.
NOTE
• The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm
(3-inch) CD, it will get stuck inside and can cause the unit to
malfunction.
The CD text, Presetting Disc Names, and Disc Name Preset Play
functions may not be operational depending on the unit.
• When the faceplate has been slid open, it might interfere with
the gear lever or something else. If this happens, pay attention
to safety and move the gear lever or take an appropriate action,
then operate the unit.
• Do not use the unit with the faceplate in the open condition.
Doing so will cause breakdown.
NOTE
Playing CDs
• When you load a CD and eject it right away, the next time you
try to insert the CD may not load. In such a situation, take the
CD out for a moment and then reinsert it.
Playing CDs:
Press the release button to slide open the faceplate, showing
the CD insertion slot.
• The only buttons that will work during the eject state are the 0
Holding the CD with the labeled side facing up, insert it in the
slot. The CD will start playing. Push back the bottom of the
faceplate with your hand until it locks.
and ATT buttons.
The "IN" indicator will light when a CD has been inserted.
2CAUTION
When inserting a CD, make sure the CD has been completely
drawn in before pushing back the faceplate. Failing to do so
— 18 —
Playing Other Disc mode
This function permits the connection of optional players and
the playing of discs other than the loaded CD (in the current
unit).
Track time
Disc name (DNPS)
Disc title (Units featuring CD text/MD only)
Playing Discs:
Press the SRC button repeatedly to select the external disc
control mode.
Track title (Units featuring CD text/MD only)
Clock
Date
The disc will start playing.
NOTE
The external disc control mode will differ, depending on the unit
that is connected.
Mode Display Examples
NOTE
• "CD2" ...when a CD player is connected
• "DISC" ...when a disc changer is connected
• "DISC-1" , "DISC-2" ...when two disc changers are connected
• You can give names to discs through the presetting disc name
function (see p. 22).
Note that depending on the unit, display may not be possible.
• If you try to display the name of a disc that does not have one,
"NO NAME" is displayed instead.
• When there is an attempt to display the title of a disc for which
the disc title/track title has not been recorded, "NO TEXT" is
displayed for CD and "NO TITLE/NO NAME" is displayed for
MD.
Pausing and Restarting Disc Play:
Press the 38 button to make the disc pause.
Press the same button again to start play again.
NOTE
• When one disc has finished playing its last track, the next disc
in the changer starts playing. When the last disc in the changer
has finished, the player returns to the first disc and starts
playing it.
• Depending on the type of characters of the CD Text, some
characters may not be displayable.
• The £ indicator lights whilst the clock is displayed.
• Disc #10 is displayed as "0".
Switching Display for Discs
Switch the display that appears whilst discs are playing.
Switching Display for Discs:
Each time you press the DISP button, the display during disc
play switches as follows.
— 19 —
CD/External disc control features
Fast Forwarding and Reversing Disc Play
Disc Search
(Function of disc changers)
Search forwards or backwards through the discs in a disc
Fast Forwarding Disc Play:
changer until you reach the one that you want to listen to.
Hold down on the ¢ button.
Egnlish
Release your finger to play the disc at that point.
Making a Reverse Disc Search:
Press the DISC– button to display the desired disc number.
Each time the button is pressed, the displayed disc number
decreases by one.
Reversing Disc Play:
Hold down on the 4 button.
Release your finger to play the disc at the point.
NOTE
Play starts at the beginning of the displayed disc.
Making a Forward Disc Search:
You cannot use reverse play between tracks depending on the
model being connected. Instead, the reverse play function is
cancelled when it reaches the beginning of a track, at which
point normal play automatically resumes.
Press the DISC+ button to display the desired disc number.
Each time the button is pressed, the displayed disc number
increases by one.
Play starts at the beginning of the displayed disc.
NOTE
"LOAD" is displayed when discs are being exchanged on the disc
changer.
Track Search
Search forwards or backwards through the tracks on the disc
until you reach the one that you want to listen to.
Track / Disc Repeat
Repeat playing the current track or disc.
Making a Reverse Track Search:
Press the 4 button to display the desired track number.
Press once to search back to the beginning of the current
track, twice to search back to the beginning of the previous
track, and so forth.
Turning Repeat Play Function On/Off:
Press the REP button to switch the repeat play function on and
off as follows :
Play starts at the beginning of the displayed track number.
▼
NOTE
Track Repeat ON
Pressing the 4 button whilst listening to track 1 only searches
back to the beginning of that track. The reverse search is not
"recycled" to the last track on the disc.
▼
Disc Repeat ON (Function of disc changers)
▼
Track/Disc Repeat OFF
Making a Forward Track Search:
Press the ¢ button to display the desired track number.
Press once to fast forward to the next track, twice to fast
forward to the track after that, and so forth.
"T-Repeat/T-REP ON" is displayed and the track number blinks
in the display when track repeat is on.
"D-Repeat/D-REP ON" is displayed and the disc number blinks
in the display when disc repeat is on.
Play starts at the beginning of the displayed track number.
NOTE
NOTE
You cannot make a forward track search when listening to the
last track on a disc.
Repeat play is cancelled when you eject the disc.
— 20 —
Track Scan
Random Play
Play all the tracks on the current disc in random order.
Successively play the beginning of each track on a disc until
you find the track that you want to listen to.
1
Press the RDM button to switch the random play function on
Starting the Track Scan:
and off.
Press the SCAN button. "T-Scan/TSCN ON" is displayed and the
first 10 seconds of each track are played, and the tracks are
played in order.
"Random/RDM ON" is displayed when random play is turned
on.
The display of the track number changes continuously as the
next track is being selected.
The track number currently being heard blinks in the display.
When the track has been selected, play starts.
The selected track number blinks in the display as it is being
played.
Stopping to Listen to the Track Being Scanned:
Press the 38 or SCAN button again to stop the scan and keep
on listening to a track normally.
NOTE
NOTE
(For disc changers)
When all the tracks on a certain disc have been played using the
random play function, the next disc on the changer starts playing
(with the random play function still turned on).
• The track scan function is cancelled when you eject the disc.
• The track scan function only scans each track on a disc once.
2
To change the track being heard, press the ¢ button.
Another track is selected and played.
NOTE
Disc Scan
(Function of disc changers)
Random play is cancelled when you eject the disc.
Successively play the beginning of each disc on a changer
until you find the one that you want to listen to.
Starting the disc scan:
Press the D.SCN button. "D-Scan/DSCN ON" is displayed and
the first 10 seconds of each disc are played, in the order in
which they are loaded on the changer.
The disc number currently being heard blinks in the display.
Stopping to Listen to the Disc Being Scanned:
Press the 38 or D.SCN button again to stop the scan and keep
on listening to the disc normally.
NOTE
• The disc scan function is cancelled when you eject the disc.
• The disc scan function only scans each disc on the changer
once.
• "LOAD" is displayed when discs are being exchanged on the
disc changer.
— 21 —
CD/External disc control features
NOTE
Magazine Random Play
(Function of disc changers)
When the disc or track to be played changes, the title is
displayed in one scrolling display.
Play the tracks on all the discs in the disc changer in random
order.
Egnlish
2
Holding down the DISP button for one second or more results
in one scrolling display of the titles.
1
Press the M.RDM button to switch the magazine random play
function on and off.
NOTE
"M-Random/MRDM ON" is displayed when magazine random
play is turned on.
Please see the menu settings (page 32) about switching between
manual scrolling and automatic scrolling.
The display of the disc and track numbers change continuously
as the next track is being selected.
When the disc/track has been selected, play starts.
The selected disc/track number blinks in the display as it is
being played.
NOTE
This function is not available with the following models:
KDC-C200/C300/C400/C301/C401
2
To change the track being heard, press the ¢ button.
Presetting Disc Names (DNPS)
Store the names of discs to be displayed when played.
Another disc/track is selected and played.
NOTE
1
Play the disc whose name you want to preset.
• Magazine random play is cancelled when you eject the disc.
• The time needed for random selection depends on the number
of discs loaded in the disc magazine.
NOTE
• This function is not available for disc changers that do not
feature the Disc Name Preset function.
• This procedure is not to be used to store the disc and track
titles for MDs that you record.
• The disc name preset function cannot be used when a disc title
name or track title is displayed.
Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
2
Hold down the NAME.S button for two seconds or more.
"NAME SET" is displayed and the disc name preset mode is
entered.
The cursor blinks in the position where character input can be
made.
To scroll manually:
1
2
Press the DISP button to display the disc title or the track title.
3
Press either the 4 or ¢ button to move the cursor to the
desired position.
Holding down the DISP button for one second or more results
in one scrolling display of the titles.
The 4 button moves the cursor to the left, and the ¢
To scroll automatically:
button to the right.
1
Press the DISP button to display the disc title or the track title.
The titles will be displayed in one scrolling display.
4
Each time the 38 button is pressed, the characters to be
— 22 —
entered change as listed below.
that you have already stored a name for, the name will be
displayed for it, too.
Press the DISC+ or DISC– button to display the desired
character.
• If you want to change the name of a disc, repeat steps 1 and 2
to display the name, and then repeat steps 3 and 4 to input the
changes.
Characters that can be displayed are as follows.
• Pressing the reset button erases the disc names stored in this
unit, but does not erase the names stored in a disc changer.
Alphabet (upper case): A ~ Z
Alphabet (lower case): a ~ z (KDC-6080R/RV Only)
Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]
Special characters: á
à
é
è
í
ì
ó
ò
ú
ù
Ñ
Ç
®
ß
‹
fl
â
ä
ê
ë
î
ï
ô
ö
û
ü
ñ
ç
©
Æ
›
fi
(KDC-6080R/RV Only)
NOTE
The operation and characters that can be entered may change
as listed below, depending on the unit that is connected.
A press of the 38 button exits the disc name preset mode.
Operations can be followed again from Step 2 at a time such
as this, and the characters to be input are selected using the
procedure described below.
Press the DISC+ or DISC– button to display the desired
character. Besides the alphabet (capital letters only) and
numbers, you can choose the following characters: /, +, –, *,
=, <, >, [ and ].
5
6
Continue steps 3 and 4 until all the characters are chosen for
the name.
Press the NAME.S button.
The disc name is stored and the disc name preset mode is
cancelled.
If you make no entry in a 10-second period, the name will be
stored with the characters input so far.
NOTE
• The number of characters and discs whose names can be
stored will differ depending on the disc changer that is
connected. Please see your disc changer manual for details.
Up to 8 characters and 30 CDs can be registered with this unit.
• Discs are identified by their total length and number of tracks. If
another disc happens to have the same specifications as one
— 23 —
Menu settings
4
¢
38
FM
Menu System
You can set the defaults for additional functions in the menu
mode.
PWR
OFF
Make a setting for each function, referring to the following
operations.
Egnlish
DISC
PTY
DAB
EJECT
SCAN
RDM
REP
D.SCN
M.RDM
MENU
AUD
1
2
Enter the menu mode
TI
VOL ADJ
DISP
LOUD
NAME.S
Hold down the MENU button for one second or more.
"MENU" is displayed when the menu mode is entered.
The function that you can adjust is indicated with the current
settings displayed.
DISC
#1 - 4
MENU
DISP AM
Selecting function to set
Press the FM button to search through the functions until you
see the one you want to adjust in the display.
Press the AM button to search through the functions
backward.
KDC-6080R/KDC-6080RV
Menu display
AUTO indicator
Example: If you want to switch the setting of the touch sensor
tone function from on to off, first search through the
functions until you see "Beep/BEEP ON" in the
display.
3
4
Changing setting for currently displayed function
Press either the 4 or ¢ button.
NEWS indicator
™ indicator
The setting will change for each function.
Example: The setting of the touch sensor tone will switch from
on to off, and "Beep/BEEP OFF" is displayed.
KDC-5080R
Menu display
Ending the menu mode
Press the MENU button.
NOTE
Make sure to end the menu mode when finished.
If you fail to end the menu mode, several functions may not
operate properly, including the Traffic Information function and
the Alarm function.
NEWS indicator AUTO indicator
™ indicator
— 24 —
Display and setting:
Touch Sensor Tone
This function produces a beep sound that accompanies button
operation. It can be switched on or off.
1
Select the display "Date Adjust/DATE ADJ" during the selecting
function in the menu system.
2
Hold down either the 4 or ¢ button for two seconds or
more to enter the Calendar adjustment mode.
The date display will blink.
Display and setting:
"Beep/BEEP ON" : Beep setting is on.
"Beep/BEEP OFF" : Beep setting is off.
3
4
5
Selecting the item (day, month, or year) to adjust
Press the 4 or ¢ button.
NOTE
The beep sound is not output from the preout jacks.
The item blinking in the display can be adjusted.
Adjusting the date
Press the FM or AM button.
The item of the date blinking in the display will change.
Manual Time Adjustment
Adjust the time manually.
Press the MENU button to end the menu mode.
NOTE
This adjustment is available only when the automatic time
adjustment is set to off. (page26)
Calendar Mode
You can set the date formats of the calendar function.
Display and setting:
1
Select the display "Clock Adjust/CLK ADJ" during the selecting
function in the menu system.
Display and setting:
1
Select the display "Date Mode/DATE MOD" during the
selecting function in the menu system.
2
Hold down either the 4 or ¢ button for two seconds or
more to enter the Manual time adjustment mode.
The time display will blink.
2
Press the 4 and ¢ button to select the date format you
want to show in the display.
The sample of the date format for today is displayed.
3
4
• Adjusting the hours
Press the FM button to advance the hours, or press the AM
button to make the hours go back.
• Adjusting the minutes
Press the ¢ button to advance the minutes, or press the
4 button to make the minutes go back.
Press the MENU button to end the menu mode.
Calendar Adjustment
Adjust the date for the unit so that you can use the calendar
function.
— 25 —
Menu settings
Memo Mode
Alphabet (upper case): A ~ Z
You can input the text to be displayed and set the date when
that text will appear in the display with the calendar function.
Alphabet (lower case): a ~ z (KDC-6080R/RV Only)
Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]
Egnlish
Display and setting:
1
Select the display "Memo Mode/MEMO MOD" during the
selecting function in the menu mode.
Special characters: á
à
é
è
í
ì
ó
ò
ú
ù
Ñ
Ç
®
ë
î
ï
ô
ö
û
ü
ñ
ç
©
Æ
›
fi
2
Hold down either the 4 or ¢ button for two seconds or
more to enter the Memo mode.
The date display will blink.
(KDC-6080R/RV Only)
• Selecting the character
Press the FM and AM button.
Press the MENU button to end the menu mode.
3
4
Selecting the set of the date and text to be displayed
Press the FM and AM button.
8
If you want to input a new text, select the blank display.
NOTE
• The text you selected automatically appears on the date you set
when the unit’s power is first turned on. (Calendar function)
Pressing the DISP button for one second or more scrolls the
display once, regardless of the text scroll setting.
Pressing a button other than the DISP button will cause the text
to disappear from the display.
• You can enter up to 32 characters for each text.
• The calendar function can be set up to 30 cases.
• To delete the date and text setting, set both the month and day
of the date to "00" or set all of the text to blanks.
Entering the month or day setting mode
Press the 4 and ¢ button to enter the month or day
setting mode.
The month display will blink enter the month setting mode, the
day display will blink enter the day setting mode.
5
6
Changing the month or day
Press the FM and AM button.
Entering the text input mode
Press the ¢ button to enter the text input mode.
The cursor blinks in the position where character input can be
made.
7
Inputting / Changing the text
• Moving the cursor
Press the 4 and ¢ button.
• Changing the type of characters
Press the 38 button.
Automatic Time Adjustment
Each time the button is pressed, the type of characters
switches as follows.
With automatic time adjustment, you can set the clock time
automatically according to time data sent from RDS stations
(after receiving RDS signals for several minutes). You can also
set the time manually if the automatic time adjustment
function is turned off. The factory default is automatic time
adjustment.
Display and setting:
"SYNC ON" : Automatic time adjustment
— 26 —
"SYNC OFF" : Manual time adjustment
Adjusting Time Automatically:
Tune into an RDS station for 3 or 4 minutes.
The time adjusts automatically to the correct local time.
NOTE
The time is not adjusted when the RDS station you are tuned to
is not transmitting a time signal. Choose another RDS station in
such a case.
— 27 —
Menu settings
The security code will be set.
Code Security Function
After a security code has been registered, power cannot be
restored if the battery is disconnected from the unit unless the
code is first input.
"RE-ENTER" will appear in the display for one second, asking
you to enter the code once again for confirmation. When
"CODE" appears in the display, you can start inputting the
code.
Egnlish
NOTE
7
8
Press the Preset button and input the security code again.
All the steps in this procedure (1 through 8) must be completed
before the code security function can be turned on. However,
once the procedure is finished, it need not be repeated.
Once the code security function has been activated, "Security /
SECURITY" disappears from the MENU system. Note that it will
no longer be possible to cancel this function afterwards.
Hold down the DISP button again for three seconds or more.
"APPROVED" will appear in the display, with the code security
function turning on. From this point on, if the unit is
disconnected from the battery, the security code must be
entered the first time that the unit's power is turned on.
"ENTER" and "CODE" will appear in the display, asking you to
input the code.
1
Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
NOTE
2
3
Hold down the MENU button for one second or more.
"MENU" is displayed and the menu mode is turned on.
If you input an incorrect security code, the code setting mode
will be cancelled automatically. Follow the steps from 4 to 8
above again.
Press the FM button repeatedly until "Security/SECURITY"
appears in the display.
Press the AM button to search in the other direction.
If you press the RESET button or remove the battery:
The first time you turn the unit on again, "CODE" will appear in
the display, asking you to input the security code.
Repeat steps 7 and 8 above, and input the security code.
You can start operating the unit again when "APPROVED"
appears in the display.
4
5
Hold down either the 4 or ¢ button for two seconds or
more.
"ENTER" will appear in the display for one second, indicating
the code setting mode has been entered. When "CODE"
appears in the display, you can start inputting the code.
NOTE
If you enter the wrong code, "WAITING" is displayed and you
cannot make further input of the code for a fixed interval (see
table below), which grows longer each time you enter the wrong
code.
Press the preset button and enter your security code.
Use the security code shown on your Car Audio Passport.
Example: Enter "3510" as your code, pressing the buttons as
follows:
When "CODE" is displayed, you can make input again.
# Times
pressed
Step
Button to press
Display
Number of wrong
inputs
Interval until next input
is allowed
1
2
3
4
#1
#2
#3
#4
4
“3”
“5”
“1”
“0”
1
2
3
4
-
6
2
1
5 minutes
1 hour
24 hours
6
Hold down the DISP button for three seconds or more.
The number of wrong inputs is displayed.
— 28 —
Display and setting:
Selectable Illumination
You can switch the colour of the button illumination between
green and red.
"Graphic/GRAP ON" : The graphic display works.
"Graphic/GRAP OFF" : The graphic display does not work.
Display and setting:
"Color Green/COL GRN" : The colour of the illumination is
green.
"Color Red/COL RED" : The colour of the illumination is red.
Black Mask
This function allows you to turn off the lower part of the
display if there is too much information in the display.
Display and setting:
Function of the KDC-6080R/KDC-6080RV
"BLK MASK/BMSK ON" : The display will turn on by using only
the upper part of the display and the
IN indicator (KDC-6080R/6080RV
only).
"BLK MASK/BMSK OFF" : The display will turn on by using the
whole part of the display.
Contrast Adjustment
This adjustment permits easy viewing of the display.
Display and setting:
"Contrast 0" – "Contrast 10"
NOTE
The initial setting value is "5" .
KEX/ec4/dB (Sound Coordinate system)
When this system is set to on, the sound coordinate factors
(Bass frequency, Bass quality, Bass extension, and Treble
frequency) appear during the audio control mode.
Function of the KDC-6080R/KDC-6080RV
Dimmer
You can dim the display.
Display and setting:
"Kex/ec4/dB (set) ON" : The sound coordinate factors appear
and can be adjusted.
"Kex/ec4/dB (set) OFF" : The sound coordinate factors are not
appeared.
NOTE
The dimmer function is not available for units if the dimmer cable
is not connected.
Display and setting:
"Dimmer ON" : The dimmer setting is on.
"Dimmer OFF" : The dimmer setting is off.
Switching Graphic Display
You can turn the movement of graphic display on and off.
The initial setting is ON.
— 29 —
Menu settings
Selecting Tuning Mode
News Bulletin Function
You can choose from three tuning modes: auto seek, preset
station seek, and manual. The "AUTO 1" indicator lights up
when auto seek tuning is selected, and the "AUTO 2" indicator
lights when preset station seek tuning is selected.
with PTY News Timeout Setting
You can arrange to have news bulletins interrupt your current
listening source, including other radio stations. When the
News Bulletin function is on, the PTY News Timeout setting
allows you to set the interval during which further news
interruption cannot take place. You can adjust the PTY news
interruption period from 10 to 90 minutes for each journey.
Egnlish
Display and setting:
"Auto/AUTO 1" : Auto seek tuning mode
"Auto/AUTO 2" : Preset station seek tuning mode
"Manual/MANUL" : Manual tuning mode
Display and setting:
"NEWS OFF/ 00min(M)/ 10min(M)/ 20min(M)/ 30min(M)/
40min(M)/ 50min(M)/ 60min(M)/ 70min(M)/ 80min(M)/ 90min(M)"
(min(M)= minutes)
: When you select the news interruption timeout interval, the
News function turns on and the NEWS indicator lights up.
When a news bulletin is received, "NEWS" will be displayed
and reception will begin at the preset volume.
Auto Memory Entry
You can automatically store all the receivable frequencies in
the band currently being listened to, and then recall them with
the touch of a button later. This function is especially useful
when you are travelling and do not know what stations are
available. Up to 6 frequencies can be stored this way.
NOTE
• If you choose the "20min(M)" setting, further news bulletins will
not be received for 20 minutes once the first news bulletin is
received.
• This function is only available if the desired station sends PTY-
code for news bulletin or belongs to <Enhanced Other
Network>-Network sending PTY-code for news bulletin.
• If you turn on the news bulletin function in the MW/LW band,
the band is switched automatically to the FM band.
However, the MW/LW band is not returned to when you turn
off the function.
Display and setting:
1
Select the display "Auto-Memory/A-MEMORY" during the
selecting function in the menu system.
2
Hold down either the 4 or ¢ button for two seconds or
more to start auto memory function.
The numbers of the preset station buttons showed in order.
When all the stations in a certain band are stored in the preset
memory, the auto memory entry stops. The tuner then plays
the last station received.
NOTE
Local Seek Function
With the local seek function turned on, auto seek tuning skips
stations with relatively poor reception.
• When the AF function is turned on whilst auto memory entry
takes place, only RDS stations (i.e., stations with RDS
capability) are stored. RDS stations that have been preset for
FM1 cannot also be preset in FM2 or FM3.
• When the local seek function is turned whilst auto memory
entry takes place, stations with poor reception are not stored.
• When the Traffic Information function is on , only the local
traffic information station frequency will be stored.
Display and setting:
"Local.S/LO.S ON" : The local seek function is on.
"Local.S/LO.S OFF" : The local seek function is off.
Cancelling Auto Memory Entry During Its Operation:
— 30 —
Press the MENU button whilst auto memory entry is taking
place to stop the process.
NOTE
Sometimes stations in the same network broadcast different
programmes or use different programme service names.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Auto TP Seek Function
When the TI function is on and poor reception conditions are
experienced when listening to a traffic information station,
another traffic information station with better reception will be
searched for automatically. This function is on, when unit is
first powered on.
AF (Alternative Frequency) Function
When poor reception is experienced, automatically switch to
another frequency broadcasting the same programme in the
same RDS network with better reception.
The ™ indicator lights up when the AF function is turned
on.
Display and setting:
"ATPS ON" : The Auto TP Seek Function is on.
If the traffic information station you are tuned to
experiences poor reception, this function
automatically seeks another TP station.
"ATPS OFF" : The Auto TP Seek Function is off.
Display and setting:
"AF ON" : The AF function is on.
"AF OFF" : The AF function is off.
NOTE
• When no other stations with stronger reception are available for
the same programme in the RDS network, you may hear the
incoming broadcast in bits and snatches. Turn off the AF
function in such a case.
• The AF function can be turned on or off even when the standby
mode has been turned on. If the power is on, the AF function
tunes in to stations that offer good reception.
Monaural Reception
When poor stereo reception is experienced, this function will
reduce noise and improve listening conditions.
Display and setting:
"Mono/MONO ON" : The monaural reception is on.
"Mono/MONO OFF" : The monaural reception is off.
Restricting RDS Region (Region Restrict Function)
You can choose whether or not to restrict the RDS channels,
received with the AF function for a particular network, to a
specific region. When the Region Restrict Function is on, the
region is restricted.
Display and setting:
"Regional/REG ON" : The Region Restrict Function is on.
"Regional/REG OFF" : The Region Restrict Function is off.
— 31 —
Menu settings
Text Scroll
This function permits the CD text, MD title, Radio text, and
Calender function to be scrolled and the entire text to be
displayed. Switching Switching between manual scrolling and
automatic scrolling is permitted. The factory default is manual
scrolling.
Egnlish
Display and setting:
"Scroll Auto/SCL AUTO" : Automatic scrolling
"Scroll Manu/SCL MANU" : Manual scrolling
— 32 —
Accessories
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
External view
Number of items
8. Reconnect the - terminal of the battery.
9. Press the reset button.
1
..........................................1
2CAUTION
..........................................2
..........................................1
2
3
4
• If your car is not prepared for this special connection-system,
consult your Kenwood dealer.
• Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
• Make sure that all cable connections are securely made by
inserting jacks until they lock completely.
• If your vehicle's ignition does not have an ACC position, or if
the ignition cable is connected to a power source with constant
voltage such as a battery cable, the power will not be linked
with the ignition (i.e., it will not turn on and off along with the
ignition). If you want to link the unit's power with the ignition,
connect the ignition cable to a power source that can be turned
on and off with the ignition key.
..........................................1
2CAUTION
The use of any accessories except for those provided might
result in damage to the unit. Make sure only to use the
accessories shipped with the unit, as shown above.
• If the fuse blows, first make sure that the cables have not
caused a short circuit, then replace the old fuse with one with
the same rating.
• Do not let unconnected cables or terminals touch metal on the
car or anything else conducting electricity. To prevent short
circuits, also do not remove the caps on the ends of the
unconnected cables or the terminals.
• Connect the speaker cables correctly to the terminals to which
they correspond. The unit may receive damage or fail to work if
you share the - cables and/or ground them to any metal part
in the car.
• After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
• Insulate unconnected cables with vinyl tape or other similar
material.
• Some disc changers need conversion cables for connection.
See the section on "Safety Precautions" for details.
• If the console has a lid, make sure to install the unit so that the
faceplate does not hit the lid when closing and opening.
• Mount the unit so that the mounting angle is 30° or less.
Installation Procedure
1. To prevent short circuits, remove the key from the ignition and
disconnect the -terminal of the battery.
2. Make the proper input and output cable connections for each
unit.
3. Connect the cable on the wiring harness.
4. Take Connector B on the wiring harness and connect it to the
speaker connector in your vehicle.
5. Take Connector A on the wiring harness and connect it to the
external power connector on your vehicle.
— 33 —
Connecting Cables to Terminals
Connector Function Guide
Rear right output (Red)
Rear left output (White)
Pin Numbers for
Cable Colour
Functions
ISO Connectors
External Power
Egnlish
Front right output (Red)
Front left output (White)
Connector
A–4
A–5
Yellow
Blue/White
Orange/White Dimmer
Battery
Power Control
Antenna Conversion Adaptor (ISO–JASO) (Accessory3)
A–6
(KDC-6080R/RV only)
A–7
A–8
Red
Black
Ignition (ACC)
Earth (Ground)
Connection
FM/AM
Antenna Cord (ISO)
antenna input
KENWOOD disc changer/DAB control input/
Display Data Output Jack
Outputs data representing the unit's current state,
causing it to appear in the external display.
To connect to this jack, a converting adapter
(optional) is necessary.
Speaker
Connector
B–1
B–2
B–3
B–4
B–5
B–6
B–7
B–8
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Wiring harness
(Accessory1)
NOTE
To connect the Disc changer or DAB unit,
consult each manual.
Green/Black
Battery cable (Yellow)
Fuse(10A)
TEL mute cable (Brown)
Connect to the terminal that is
grounded when either the telephone
rings or during conversation.
Ignition cable (Red)
TEL MUTE
NOTE
To connect the KENWOOD navigation
system, consult your navigation manual.
Connect either to the power control
terminal when using the optional
power amplifier, or to the antenna
control terminal in the vehicle.
Power control/ Motor antenna
control cable (Blue/White)
A–7 Pin (Red)
P.CONT
A–4 Pin (Yellow)
ANT.CONT.
8
7
6
5
4
3
2
1
Connector A
Connector B
NOTE
If no connections are
made, do not let the cable
come out from the tab.
8
7
6
5
4
3
2
1
— 34 —
Connecting Cables to Terminals
Installation
■
Installation
2WARNING
Connecting the ISO Connector (see p.34)
The pin arrangement for the ISO connectors depends on the
type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
The default connection for the wiring harness is described in 1
below. If the ISO connector pins are set as described in 2 or 3,
make the connection as illustrated.
Firewall or metal support
Screw (M4X8)
(commercially
available)
1 The A-7 pin (red) of the vehicle's ISO connector is linked with
the ignition, and the A-4 pin (yellow) is connected to the
constant power supply.
Unit
Vehicle
A–7 Pin (Red)
Bend the tabs of the
mounting sleeve
with a screwdriver or
similar utensil and
attach it in place.
Ignition cable (Red)
Self-tapping
screw
(commercially
available)
Battery cable (Yellow)
A–4 Pin (Yellow)
Metal mounting
strap
(commercially
available)
2 The A-7 pin (red) of the vehicle's ISO connector is connected
to the constant power supply, and the A-4 pin (yellow) is
linked to the ignition.
NOTE
Unit
Vehicle
Make sure that the unit is installed securely in place. If the unit
is unstable, it may malfunction (eg, the sound may skip).
Ignition cable (Red)
A–7 Pin (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
3 The A-7 pin (red) of the vehicle's ISO connector is not
connected to anything, whilst the A-4 pin (yellow) is
connected to the constant power supply (or both the A-7 (red)
and A-4 (yellow) pins are connected to the constant power
supply).
Unit
Vehicle
Connect to a power source that can be
turned on and off with the ignition key.
Ignition cable (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
— 35 —
Installation
■
■
Removing the hard rubber frame
Removing the Unit
1
Refer to the section “Removing the hard rubber frame (P. 36)”
and then remove the hard rubber frame.
1
Refer to the section “Theft deterrent faceplate (P. 10)” and
then remove the faceplate.
2
3
Remove the Hex-head screw with integral washer (M4×8) on
E
2
Engage the catch pins on the removal tool and remove the
two locks on the upper level.
Push upward the frame and pull it forward as shown in the
figure.
the back panel.
Insert the two removal tools deeply into the slots on each
side, as shown.
Screw
(M4X8)
Catch facing up
(commerciall
y available)
Lock
Catch
Accessory2
Removal tool
Accessory2
Removal tool
4
Push upward the removal
tool toward the top, and
pull out the unit halfway
whilst pressing towards the
inside.
3
When the upper level is removed, remove the lower two
locations.
2CAUTION
Be careful to avoid injury from the catch pins on the removal
tool.
5
Pull the unit all the way out
with your hands, being
careful not to drop it.
NOTE
The frame can be removed from the bottom side in the same
manner.
— 36 —
Locking the faceplate to the unit
■
Locking the faceplate to the unit
If you want to lock the faceplate to the unit so that it does not
fall off, follow the directions below.
1
2
Refer to the function "Theft deterrent faceplate" (page 10) and
remove the faceplate.
Insert the provided screw into the hole at the centre of the
bottom side of the faceplate which you have removed from
the unit.
Accessory4
3
4
Push back the bottom of the faceplate bracket unit it locks.
Refer to the section "Theft deterrent faceplate (page 10)" and
then .reattaching the faceplate.
2CAUTION
Never insert the taptite screws (ø2 × 6 mm) in any other screw
holes than the one specified. If you insert it in another hole, it
will contract and may cause damage to the mechanical parts
inside the unit.
— 37 —
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not turn on.
The fuse has blown.
After checking for short circuits in the cables, replace
the fuse with one having the same rating.
Egnlish
No ACC position on vehicle ignition.
The Attenuator function is turned on.
Connect the same cable to the ignition as the battery cable.
Turn off the Attenuator function.
No sound can be heard, or the
volume is low.
The fader and/or balance settings are set all the way to
one side.
Reset the fader and/or balance settings.
The input/output cables or wiring harness are connected
incorrectly.
Reconnect the input/output cables and/or the wiring
harness correctly. See the section on "Connecting
Cables to Terminals".
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see page 4).
Check the speaker wiring.
A speaker cable may be pinched by a screw in the car.
The speakers are not wired correctly.
The sound quality is poor or
distorted.
Reconnect the speaker cables so that each output
terminal is connected to a different speaker.
Radio reception is poor.
The car antenna is not extended.
Pull out the antenna all the way.
The antenna control cable is not connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The memory is erased when
the ignition is turned off.
The battery cable has not been connected to the proper
terminal.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The ignition and battery cable are incorrectly connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
A CD ejects as soon as it is
loaded.
The CD is upside-down.
The CD is quite dirty.
Load the CD with the labelled side up.
Clean the CD, referring to the section on "Cleaning CDs"
(see page 6).
The sound skips on a CD.
The CD is scratched or dirty.
Clean the CD, referring to the section on "Cleaning CDs"
(see page 6).
The specified track does not
play.
Random play has been selected.
Turn off the random play function.
— 38 —
Troubleshooting Guide
PROBLEM
POSSIBLE CAUSE
SOLUTION
The TEL mute function does
not work.
The TEL mute cable is not connected properly.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function turns
on even though the TEL mute
cable is not connected.
The TEL mute cable is touching a metal part of the car.
Pull the TEL mute cable away from the metal part of the
car.
CD/MD/External disc control mode
PROBLEM
POSSIBLE CAUSE
SOLUTION
The disc control mode cannot
be selected.
No cable has been connected to the disc changer input
terminal on the unit.
Connect the cable to the disc changer input terminal on
the unit.
The specified disc does not
play, but another one plays
instead.
The specified CD is very dirty.
Clean the CD.
The CD is upside-down.
Load the CD with the labelled side up.
The disc is loaded in a different slot from that specified.
Eject the disc magazine and check the number for the
specified disc.
The disc is severely scratched.
Something is touching the disc changer.
The CD is scratched or dirty.
Try another disc instead.
The sound skips.
Remove whatever is touching it.
If skipping happens at the same place when the car is
stopped, something is wrong with the CD. Clean the CD.
The display shows that the
changer is being played, but no
sound can be heard.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see page 4).
The specified track does not
play.
Random play or magazine random play has been
selected.
Turn off the random play or magazine random play
function.
Track repeat, disc repeat, track
scan, disc scan, random play,
and magazine random play
start by themselves.
The setting is not cancelled.
The settings for these functions remain on until the
setting to off or the disc ejected, even if the power is
turned off or the source changed.
If the following situations, consult your nearest service centre:
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered
when switching modes.
— 39 —
Troubleshooting Guide
The following messages are displayed when certain problems are occurring in your system. Take the
recommended actions.
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.
EJECT
]
Load the disc magazine properly.
No CD in the unit.
Egnlish
]
Insert the CD.
No disc has been loaded in the disc magazine.
NO DISC
E-04
]
Load a disc into the disc magazine.
No disc has been loaded in the disc magazine.
]
Load a disc into the disc magazine.
The CD is very dirty. The CD is upside-down. The CD is scratched a lot.
]
Clean the CD and load it correctly.
Nothing has been recorded on the MD.
BLANK
No tracks are recorded on the MD, although it has a title.
NO TRACK
NO PANEL
The faceplate of the slave unit being connected to this unit has been removed.
]
Replace it.
The unit is malfunctioning for some reason.
E-77
E-99
]
Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.
]
Check the disc magazine. And then, press the reset button on the unit.
If the "E- 99" code does not disappear, consult your nearest service center.
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),
stopping all operation.
HOLD
IN
]
Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),
the disc starts playing again.
If this indicator blinks, the CD player is malfunctioning.
] Eject the CD and try inseting it again.
If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected.
— 40 —
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency Range (50 kHz Space)..................87.5MHz-108.0MHz
Usable Sensitivity (S/N: 26dB) ...................................0.7 µV/75 Ω
Quieting Sensitivity (S/N: 46dB).................................1.6 µV/75 Ω
Frequency Response ( 3.0dB)...................................30Hz-15kHz
Signal to Noise ratio ...............................................65dB(MONO)
Selectivity (DIN) ..............................................≥ 80 dB( 400 kHz)
Stereo Separation .......................................................35dB(1kHz)
Maximum output power.....................................................45wx4
Full Bandwidth Power (DIN45324,+B=14.4V ) ...................28wx4
Tone action
Bass .............................................................100Hz 10dB
Treble ...........................................................10kHz 10dB
Preout Level(mV)/Load ...........................................1800mV/10kΩ
Preout Impedance (During CD play) ...................................≤600Ω
MW tuner section
General
Frequency Range (9 kHz space) .........................531kHz-1611kHz
Usable Sensitivity (S/N: 20dB) .............................................25 µV
Operating voltage (11 - 16V allowable) ...............................14.4 V
Current Consumption .............................................................10A
Installation Size (W x H x D) ..........................182 x 53 x 161 mm
Weight ................................................................................1.8 kg
LW tuner section
Frequency Range .................................................153kHz-281kHz
Usable Sensitivity (S/N: 20dB) .............................................45 µV
CD player section
Laser diode....................................................GaAlAs (λ=780 nm)
Digital filter (D/A) ......................................8 Times OverSampling
D/A Converter .......................................................................1 Bit
Spindle speed ..............................................500 – 200 rpm (CLV)
Wow & Flutter .........................................Below Mesurable Limit
Frequency response....................................10Hz - 20kHz ( 1 dB)
Total harmonic distortion..........................................0.01%(1kHz)
Signal to Noise ratio ...................................................93dB(1kHz)
Dynamic range .....................................................................93dB
Channel separation...............................................................85dB
— 41 —
|