COMPACT VHS CAMCORDER
ENGLISH
GR-AX999UM
Compact VHS
INSTRUCTIONS
LYT0108-001A
EN
EN
3
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
Electrical energy can perform many useful func-
tions. But improper use can result in potential
electrical shock or fire hazards. This product has
been engineered and
If an outside antenna or cable system is connected
to the product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conduc-
tors, location of antenna discharge unit, connection
to grounding electrodes, and
manufactured to assure your personal safety. In
order not to defeat the built-in safeguards, observe
the following basic rules for its installation, use and
servicing.
ATTENTION:
Follow and obey all warnings and instructions
marked on your product and its operating instruc-
tions. For your safety, please read all the safety and
operating instructions before you operate this
product and keep this manual for future reference.
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product
due to lightning and power-line surges.
INSTALLATION
1. Power Sources
Operate your product only from the type of power
source indicated on the marking label. If you are
not sure of the type of power supply to your home,
consult your product dealer or local power
company. If your product is intended to operate
from battery power, or other sources, refer to the
operating instructions.
3. Power Lines
An outside antenna system should not be located in
the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
2. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
3. Power Cord Protection
Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience recepta-
cles, and the point where they exit from the
product.
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
4. Ventilation
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the
product and to protect it from overheating, these
openings must not be blocked or covered.
•Do not block the openings by placing the product
on a bed, sofa, rug or other similar surface.
•Do not place the product in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
5. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
4
EN
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits
a marked change in performance and you are
unable to restore normal operation by following the
detailed procedure in its operating instructions, do
not attempt to service it yourself as opening or
removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
•Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall, causing
serious injury to a child or adult, and serious
damage to the product.
•Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the product.
•Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
•Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
2. Product and Cart Combination
A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combina-
tion to overturn.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
3. Water and Moisture
Do not use this product
near water—for example,
near a bath tub, wash
bowl, kitchen sink or
laundry tub, in a wet
basement, or near a
swimming pool and the
like.
PORTABLE CART WARNING
(Symbol provided by RETAC)
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
4. Object and Liquid Entry
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any
kind on the product.
5. Attachments
4. Safety Check
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in safe
operating condition.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
MAJOR FEATURES
EN
5
REMEMBER
Digital Still Camera Built-in
(PC communication capable)
(੬ pg. 46 – 61)
The Logical Choice
Integrated Auto Light
(੬ pg. 23)
The only compact video
cassettes that can be
used with your VHS VCR*
Picture Stabilizer (੬ pg. 21)
Program AE with Special
Effects (੬ pg. 26, 27)
Ⅲ Auto Mode Lock
Ⅲ Auto Mode Release
Ⅲ Electronic Fog Filter
Ⅲ ND Effect
Digital Hyper Zoom
(੬ pg. 20)
Ⅲ Sepia
Ⅲ Twilight
Ⅲ Sports
Zoom-in
Ⅲ Nega/Posi
Ⅲ 1/2000 sec. High Speed Shutter
Zoom-out
Program Manager II
(੬ pg. 26 – 39)
Program AE with Special Effects,
Fade/Wipe, Wide, Super LoLux,
Instant Title, Menu Adjustment
(Focus, Exposure Control and so on.)
Cassettes marked
camcorder.
can be used with this
QUICK OPERATION GUIDE (VIDEO)
6
EN
INSERTING A VIDEO
CASSETTE
SUPPLY POWER
Hook on.
1
EJECT
Push in.
2
1
BATT. RELEASE
PUSH
3
2
Using the battery pack
1 Hook-on the battery pack’s top end to the
camcorder. (Charging procedure, ੬ pg. 10)
2 Push in the battery pack until it locks into
place.
1 Slide EJECT to open the cassette holder.
2 Insert a video cassette.
3 Press PUSH to close the cassette holder.
(For more details, ੬ pg. 17)
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
PLAYBACK
SHOOTING
2
Set to “VIDEO”
PLAY/PAUSE
STOP
4
Set to “VIDEO”
1
REW
3
1
LENS COVER
Open/Close
Switch
2
3
Set to
Set to “CAMERA”
“PLAY”
4
Recording Start/Stop Button
1 Set the System Select Switch to “VIDEO”.
2 Set the Power Switch to “PLAY”.
3 Press REW.
1 Slide the LENS COVER Open/Close Switch
to open the lens cover.
2 Set the System Select Switch to “VIDEO”.
3 Set the Power Switch to “CAMERA”.
— The power indicator will light and an
image will appear.
— The tape will automatically stop at the
beginning of the tape.
4 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears.
4 Press the Recording Start/Stop Button.
— Recording starts.
• To stop playback, press STOP.
(For more details, ੬ pg. 40.)
•To stop recording temporarily, momentarily
press the Recording Start/Stop Button once
again.
Or simply play back the tape on a VHS VCR
using the Cassette Adapter (VHS Playpak).
੬ pg. 43
(For more details, ੬ pgs. 18, 19)
QUICK OPERATION GUIDE (D.S.C.)
EN
7
SUPPLY POWER
SHOOTING
System Select Switch Set to “D.S.C.”
2
SNAPSHOT Button
4
Hook on.
1
1
Push in.
2
LENS COVER
Open/Close
BATT. RELEASE
Switch
3
Power Switch
Set to “CAMERA”
Using the battery pack
1 Slide the LENS COVER Open/Close Switch
to open the lens cover.
2 Set the System Select Switch to “D.S.C.”.
3 Set the Power Switch to “CAMERA”.
— The power indicator will light and an
image will appear.
1 Hook-on the battery pack’s top end to the
camcorder. (Charging procedure, ੬ pg. 10)
2 Push in the battery pack until it locks into
place.
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
4 Press the SNAPSHOT Button.
— A still image is shot and is stored in the
camcorder’s memory.
(For more details, ੬ pg. 46)
PLAYBACK
Page Button
3
1
System Select
Switch Set to
“D.S.C.”
2
Power Switch
Set to “PLAY”
1 Set the System Select Switch to “D.S.C.”.
2 Set the Power Switch to “PLAY”.
— A still image stored in memory appears.
3 Press “W” or “T” of the Page Button to select
the still image you want to view.
(For more details, ੬ pg. 53.)
CONTENTS
8
EN
GETTING STARTED
10
Power ..................................................................................... 10
Clock (Lithium) Battery Insertion/Removal .......................................... 12
Date/Time Setting....................................................................... 13
Grip Adjustment ......................................................................... 14
Viewfinder Adjustment ................................................................. 14
Shoulder Strap Attachment ............................................................. 15
Tripod Mounting.......................................................................... 15
Recording Mode Setting ................................................................ 16
Tape Length Setting ..................................................................... 16
Loading/Unloading A Cassette ........................................................ 17
VIDEO RECORDING
18
Basic Recording .......................................................................... 18
Basic Features............................................................................ 20
Advanced Features ...................................................................... 26
VIDEO PLAYBACK
40
Basic Playback ........................................................................... 40
Features................................................................................... 41
Using The Cassette Adapter ............................................................ 43
BASIC CONNECTIONS TO VCR
TAPE DUBBING
44
45
46
DIGITAL STILL CAMERA (D.S.C.) SHOOTING
Basic Shooting............................................................................ 46
Advanced Features ...................................................................... 48
D.S.C. PLAYBACK
53
Basic Playback ........................................................................... 53
Advanced Features ...................................................................... 54
Connection ................................................................................ 61
USING REMOTE CONTROL UNIT
62
Random Assemble Editing .............................................................. 64
Insert Editing (VIDEO)................................................................... 68
Insert Editing (Insert A Still Image From The Built-in Memory Onto A Tape).... 69
Audio Dubbing............................................................................ 70
EN
9
USER MAINTENANCE
INDEX
71
72
Viewfinder Indications .................................................................. 73
Controls ................................................................................... 74
Connectors ................................................................................ 74
Indicators ................................................................................. 74
Other Parts ............................................................................... 74
Terms ...................................................................................... 76
TROUBLESHOOTING
CAUTIONS
78
81
84
84
SPECIFICATIONS
OPTIONAL ACCESSORIES
PROVIDED ACCESSORIES
•AC Power Adapter/
Charger AA-V15U
•Cassette Adapter
(VHS Playpak) C-P7U
•Battery Pack
BN-V18U
•Remote Control
Unit RM-V705U
•Shoulder Strap
•DC Cord
(for Macintosh®)
•Lithium Battery
CR2025 x 2 (for
clock operation
and remote
(for Windows® PC)
•CD-ROM including
two software
programs
•PC Connection Cable x 2
control unit)
GETTING STARTED
10
EN
Marks
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
To AC outlet
CHG. (charge)
indicator
NOTES:
● No function is available without power supply.
● Use only specified power supply.
● Do not use provided power supply units with other
equipment.
CHARGING THE BATTERY PACK
REFRESH switch
SUPPLY POWER
Connect the charger’s AC power cord to a wall
REFRESH indicator
REFRESH
1
2
outlet.
ATTACH BATTERY PACK
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The AC power adapter features a REFRESH
function that allows you to fully discharge
the battery pack before recharging.
Perform the REFRESH function after no less
than 5 chargings.
•The CHG. indicator begins blinking to indicate
charging has started.
To discharge the battery . . .
DETACH BATTERY PACK
..... attach the battery pack to the adapter
as shown in the above illustration.
Then push REFRESH. The REFRESH
indicator lights when discharging
starts, and goes out when discharging
is complete.
When the CHG. indicator stops blinking but stays lit,
charging is finished. Slide the battery pack opposite
the direction of the arrow.
3
BATT. PACK
CHARGE
DISCHARGE
BN-V12U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V18U approx. 1 hr. 40 min. approx. 5 hrs. 30 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.
BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.
USING THE BATTERY PACK
Hook on.
ATTACH BATTERY PACK
1
Hook its top end to the camcorder and push the
1
2
battery pack in until it locks in place.
DETACH BATTERY PACK
Slide BATT. RELEASE and pull out the battery pack.
Push in.
2
BATT. PACK
Approximate recording time (unit: min.)
BATT. RELEASE
BN-V12U
65
100
135
180
( 40 )
( 65 )
BN-V18U
BN-V22U
BN-V25U
ATTENTION:
( 85 )
Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.
( 110 )
(
) : when the video light is on.
EN
11
CHARGE MARKER
(OPTIONAL BATTERY ONLY)
Charge marker
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colors are provided (red and black)—you
choose which one means charged and which
means discharged.
• The battery pack BN-V18U does not have a
charge marker.
NOTES:
● The recording time per charge is affected by such factors as the time spent in Record-Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
● Charging times noted on page 10 are for fully discharged battery pack, and discharging times are for fully
charged battery pack.
● Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
● Perform the REFRESH function after no less than 5 chargings.
● While the AC Power Adapter/Charger’s power cord is disconnected from the AC outlet, it is possible to
discharge the battery by pressing the REFRESH switch. During that time, the AC Power Adapter/Charger
does not charge the battery. When discharging is complete, detach the battery from the AC Power Adapter/
Charger to store it.
● High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
● If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
● Remove the battery pack from the adapter immediately after discharging.
● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
● Make sure you unplug the DC cord before charging or discharging the battery pack.
● The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should blink during recharging. If not, contact your nearest JVC dealer.
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
To AC outlet
DC OUT
terminal
To DC
IN jack
NOTES:
● When using the car battery, leave the engine
idling.
AC Power
Adapter/Charger
AA-V15U
● The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.
● When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.
DC cord
To car’s
cigarette
lighter socket
Car Battery Cord
AP-V7U (optional)
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
Car Battery Charger/Adapter
BH-V3U (optional)
GETTING STARTED (cont.)
12
EN
Clock (Lithium) Battery Insertion/Removal
A
This battery is necessary for clock operation and to
perform date/time settings.
SWITCH OFF POWER
Switch off the unit’s power and remove the power
1
2
3
supply unit.
OPEN COVER
Open the clock battery compartment cover while
pressing the release tab.
REMOVE BATTERY (when replacing)
Insert a pointed, non-metallic object between the
A
battery and the compartment ( ) and pull the
battery out.
INSERT BATTERY
Ensure that the plus (+) side is up and insert a
CR2025 lithium battery and push it in.
4
5
CLOSE COVER
Close the compartment cover until it clicks in place.
NOTE:
See “SAFETY PRECAUTIONS” (੬ pg. 2) for information
on safe handling of lithium batteries.
EN
13
Date/Time Setting
ACCESS MENU SCREEN
First set the Power Switch to “CAMERA”. Turn the
Select Dial to any position except AUTO LOCK,
then press the MENU Jog Dial.
1
2
SELECT FUNCTION
Rotate the MENU Jog Dial to move the highlight bar
to “DATE/TIME”, then press it. The DATE/TIME
Setting Menu appears.
•If you decide you want to return the date and time
to the previous settings, rotate the MENU Jog Dial
to move highlight bar to “EXIT” and press it, then
go to step 6.
•If you want to set only the time without changing
the date, go to step 4.
Select Dial
MENU Jog Dial
Menu Screen
Viewfinder
SET DATE
MENU
Rotate the MENU Jog Dial to move the highlight bar
to the item you want to set and then press it. When
the setting begins blinking, rotate the MENU Jog
Dial until the correct setting appears and then press
it. The setting stops blinking.
4
MENU END
3
4
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
JAN 1.98
TELE MACRO OFF
TAPE LENGTH T30
When the System
Select Switch is
set to “D.S.C.”,
“PICTURE” is
displayed.
M. W. B.
AUTO
ZOOM SPEED FAST
•Repeat this procedure until you’re satisfied with
the Date settings (“YEAR”, “MONTH” and “DAY”).
4
NEXT
SET TIME
DATE TIME
Rotate the MENU Jog Dial to move the highlight bar
to “TIME” and then press it. When the hour setting
begins blinking, rotate the MENU Jog Dial until the
correct setting appears and then press it. When the
hour setting stops blinking and the minute setting
begins blinking, rotate the MENU Jog Dial until the
correct setting appears and then press it. The minute
setting stops blinking.
DATE/TIME
Setting Menu
YEAR
1998
JAN
MONTH
DAY
1
TIME
PM 12:00
12-hour
indication with
AM or PM
EXIT
START CLOCK OPERATION
MENU
When none of these settings (YEAR, MONTH, DAY,
TIME) blinks, rotate the MENU Jog Dial to move the
highlight bar to “EXIT”, and press it. The Menu
Screen appears and “MENU END” is highlighted.
4
MENU END
5
6
FOCUS
AUTO
EXPOSURE
DATE TIME
TELE MACRO OFF
TAPE LENGTH T30
AUTO
DEC 25.98
M. W. B.
AUTO
CLOSE MENU
ZOOM SPEED FAST
Press the MENU Jog Dial.
4NEXT
NOTE:
To display the date and time in the viewfinder and on a
connected TV, see “Date/Time Insert” (੬ pg. 22).
GETTING STARTED (cont.)
Grip Adjustment
14
EN
Power Zoom Button
EXPAND LOOP
Separate the Velcro strip.
1
2
3
INSERT HAND
Pass your right hand through the loop and grasp the
grip.
ADJUST STRAP LENGTH
Adjust so your thumb and fingers can easily operate
the Recording Start/Stop Button and Power Zoom
Button. Refasten the Velcro strip.
Recording Start/Stop Button
Viewfinder Adjustment
POSITION VIEWFINDER
3
Adjust the viewfinder manually for best viewability
1
2
3
(see illustration at left).
SELECT MODE
1
Set the Power Switch to “CAMERA”.
2
ADJUST DIOPTER
Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.
Set POWER to “CAMERA”.
EN
15
Shoulder Strap Attachment
ATTACH STRAP
Following the illustration at left, thread the strap
through the top of the eyelet 1, then fold it back
and thread it through the buckle 2. Repeat the
procedure to attach the other end of the strap to the
other eyelet 3, making sure the strap isn’t twisted.
1
2
2
1
1
3
ADJUST LENGTH
Adjust as shown in the illustration at left 1.
Tripod Mounting
ALIGN AND TIGHTEN
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
1
CAUTION:
When using a tripod, be sure to open and extend
its legs fully to stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.
VIDEO GETTING STARTED
16
EN
Recording Mode Setting
SP/EP Recording
Mode Button
Set depending on your preference.
SET RECORDING MODE
First set the System Select Switch to “VIDEO”, then
1
set the Power Switch to “CAMERA”. Press SP/EP
Button for more than 1 second. “SP” (Standard Play)
provides higher picture and sound quality and is
better for dubbing, while “EP” (Extended Play) is
more economical, providing three times as the
recording time.
NOTE:
Select Dial
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
MENU Jog Dial
System Select Switch
Tape Length Setting
Viewfinder
Set the tape length according to the length of the tape
used.
Tape length
indicator
T40
SP
ACCESS MENU SCREEN
Recording mode
indicator
First set the System Select Switch to “VIDEO”, then
1
set the Power Switch to “CAMERA”. Turn the Select
Dial to any position except AUTO LOCK, then press
the MENU Jog Dial.
SELECT FUNCTION
MENU
Menu Screen
Rotate the MENU Jog Dial to move the highlight bar
to “TAPE LENGTH”, then press it. The TAPE
LENGTH Setting Menu appears.
4
MENU END
2
3
FOCUS
AUTO
EXPOSURE
DATE TIME
TELE MACRO OFF
TAPE LENGTH T40
AUTO
DEC 25.98
SET TAPE LENGTH
M. W. B.
AUTO
Rotate the MENU Jog Dial to move the highlight bar
to the correct setting. T20=20 minutes of recording
time, T30=30 minutes, and T40=40 minutes (in SP).
ZOOM SPEED FAST
4NEXT
•If you decide you want to return the tape length to
the previous setting, rotate the MENU Jog Dial to
move the highlight bar to “EXIT”.
TAPE LENGTH
TAPE LENGTH
Setting Menu
T20
T30
T40
CLOSE MENU
Press the MENU Jog Dial. The Menu Screen
reappears and the highlight bar is on “MENU END”.
Then press the MENU Jog Dial again to close the
Menu Screen.
4
EXIT
NOTES:
MENU
● The tape remaining time (੬ pg. 19) displayed in the
viewfinder is correct only if the correct tape length has
been selected.
● Once you have set the tape length, it remains un-
changed even if the Select Dial is returned to AUTO
LOCK.
4
MENU END
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T20
M. W. B.
AUTO
ZOOM SPEED FAST
● When the System Select Switch is set to “D.S.C.”, it is
not possible to set “REC TIME” and “TAPE LENGTH”.
4NEXT
EN
17
Loading/Unloading A Cassette
OPEN CASSETTE HOLDER
Slide EJECT until the holder opens. Do not use force
1
2
3
to open.
1
INSERT/REMOVE CASSETTE
Make sure the label is facing outward.
3
2
CLOSE CASSETTE HOLDER
Press PUSH and make sure the holder is closed and
locked.
NOTES:
● A cassette holder can’t be opened unless a power
supply is attached.
● Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
Turn to take
up slack.
Gear
Erase Protection
● Make sure the Erase Protection tab is in the position
that allows recording. If not, slide the tab. Some
cassettes have removable tabs. If the tab has been
removed, cover the hole with adhesive tape.
● The cassette holder can’t be opened while the
camcorder is in the record mode.
VIDEO RECORDING Basic Recording
18
EN
NOTE:
LENS COVER Switch
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 10)
● Recording Mode/Tape Length Setting (੬ pg. 16)
● Grip Adjustment (੬ pg. 14)
LOAD A CASSETTE
Power
indicator
Slide EJECT to open the cassette holder, then insert
1
2
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
Power Switch
Start/Stop Button
ENTER RECORD-STANDBY MODE
Slide the LENS COVER Open/Close Switch to open
the lens cover. Set the System Select Switch to
“VIDEO”, then set the Power Switch to “CAMERA”.
•The power indicator lights and the camcorder
enters the Record-Standby mode.
•The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
System Select Switch
START SHOOTING
Press the Recording Start/Stop Button.
3
•“REC ” appears in the viewfinder while recording is
in progress.
Tally lamp
(lights while recording
is in progress)
EN
19
Tape remaining time indicator
STOP RECORDING
25MIN
MIN
Press the Recording Start/Stop Button again to stop
recording.
(Now calculating)
4
•The camcorder re-enters the Record-Standby
mode.
120MIN
119MIN
NOTES:
● A cassette holder can’t be opened unless a power supply
is attached.
● There may be a delay after you press EJECT until the
holder opens. Do not use force.
● The displayed remaining time is approximate.
● The time required to calculate the remaining tape
length, and the accuracy of the calculation, may vary
according to the type of tape used.
3MIN
2MIN
(Blinking)
1MIN
● The tape remaining time indicator is correct only if the
correct tape length has been selected (੬ pg. 16).
● “TAPE END” appears when the tape reaches its end,
and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears
when a cassette whose tape is already at its end is
loaded.
● If the Record–Standby mode continues for 5 minutes
without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the
Power Switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.
● If the Recording Start/Stop Button is pressed after the
Record-Standby mode has continued for over
5 minutes, recording may not start immediately.
● If you’re recording on a cassette from the middle (such
as when a tape is removed and re-inserted during
recording), use the Retake function (੬ pg. 21) to find
the end of the last recording so you don’t erase any of
it.
(Blinking)
0MIN
(Blinking)
Start/Stop Button
● The LENS COVER warning blinks for about 5 seconds
when the camcorder is turned on when the cover is
closed.
VIDEO RECORDING Basic Features
20
EN
FEATURE:
PURPOSE:
Zooming
Zoom-in
To produce the zoom in/out effect, or
an instantaneous change in image
magnification.
Digital circuitly doubles the maximum
22x magnification offered by optical
zoom. This system is called Digital Zoom.
OPERATION:
Zoom In
Zoom-out
Press the “T” of the Power Zoom Button.
Zoom Out
Press “W” of the Power Zoom Button.
Ⅲ Zooming speed is available. A total of
4 zoom speeds are available. 2 speeds
can be selected depending on how
hard the Power Zoom Button is
pressed (press the button fully for
regular-speed, press it lightly for slow-
speed), while 2 speed levels (FAST/
SLOW) can be selected in the ZOOM
SPEED Menu depending on the overall
speed you prefer.
Zoom indicator bar
Zoom Level
indicator
The combinations of zoom speeds are
shown in the chart below.
Power Zoom button
Changing the ZOOM SPEED in the
Menu
1) Set the Select Dial to any position
except AUTO LOCK and press the
MENU Jog Dial. The Menu Screen
appears.
2) Rotate the MENU Jog Dial to move
the highlight bar to “ZOOM SPEED”,
then press it. The ZOOM SPEED
Setting Menu appears.
3) Rotate the MENU Jog Dial to move
the highlight bar to the desired speed
and press it twice. The Menu Screen
disappears and setting is completed.
● Focusing may become unstable
during Zooming. In this case, set the
zoom while in Record–Standby, lock
the focus by using the manual focus
(੬ pg. 35), then zoom in or out in
Record mode.
● The zoom level indicator (5) moves
during zoom. Once the zoom level
indicator reaches the top of the zoom
indicator bar, all magnification from
that point is through digital process-
ing.
Select Dial
MENU Jog Dial
Menu Screen
NOTES:
Viewfinder
MENU
4
MENU END
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
JAN 1.98
TELE MACRO OFF
TAPE LENGTH T30
M. W. B.
AUTO
ZOOM SPEED FAST
4
NEXT
● During Digital Zoom, the quality of
image may suffer. To deactivate Digital
Zoom, set “D.ZOOM” to “OFF” in
the Menu Screen (੬ pg. 33).
ZOOM SPEED
ZOOM SPEED
Setting Menu
FAST
SLOW
Zooming Speed ( 1– 4 in order of speed)
Pressing the Power Zoom Button
“ZOOM SPEED” in
the Menu Screen
fully
lightly
3
EXIT
FAST
1 (fastest)
2
SLOW
4 (slowest)
: when the Select Dial is set to AUTO LOCK.
EN
21
FEATURE:
PURPOSE:
Quick Review
To check the end of the last record-
ing.
OPERATION:
1) Press “ ” and release quickly
during the Record–Standby mode.
Ⅲ Tape is rewound for about 2
seconds and played back
automatically, then pauses in
Record–Standby mode for the
next shot.
P. STABILIZER
RETAKE (R/F)
NOTE:
Distortion may occur at start of
playback. This is normal.
FEATURE:
Retake
PURPOSE:
OPERATION:
To re-record certain segments.
1) Make sure the camcorder is in the
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording. Pressing “F” forwards
the tape and pressing “R” reverses
it.
3) Press Recording Start/Stop Button
to start recording.
NOTE:
Noise may appear during Retake.
This is normal.
FEATURE:
PURPOSE:
Picture Stabilizer
To compensate for unstable images
caused by camera-shake, particularly
at high magnification.
OPERATION:
NOTES:
1) Press P. STABILIZER. “ ”appears.
Ⅲ To switch off the Picture
Stabilizer, press P. STABILIZER.
The indicator disappears.
● Accurate stabilization may not be
possible if hand shake is excessive,
or under the following conditions:
•When shooting subjects with
vertical or horizontal stripes.
•When shooting dark or dim
subjects.
•When shooting subjects with
excessive backlighting.
•When shooting scenes with
movement in various directions.
•When shooting scenes with low-
contrast backgrounds.
● Switch off the Picture Stabilizer
when recording with the
camcorder on a tripod.
VIDEO RECORDING Basic Features (cont.)
22
EN
DATE/TIME
FEATURE:
PURPOSE:
Date/Time Insert
To display the date and time in the
viewfinder or on a connected color
monitor, as well as to record them
manually or automatically.
OPERATION:
1) Turn the Select Dial to any
position except AUTO LOCK.
2) Choose a display mode by
pressing DATE/TIME repeatedly
while in Record-Standby to cycle
through the modes as shown in the
illustration at left.
Display
Select Dial
Ⅲ You should have already
performed the Date/Time Setting
procedure (੬ pg. 13). If you
haven’t, do so first.
NOTES:
DISPLAY
● The selected display can be
recorded.
Date display
● If you don’t want to record the
display, select the Date-off mode
before shooting.
Time display
● If you want to delete the display
during shooting, press DATE/TIME.
● To recall the display, engage the
Record-Standby mode and press
DATE/TIME repeatedly until the
desired display appears.
Date/Time display
Auto Date Record mode
Date-off mode (No display)
● Even if you shoot with the date/
time displayed during Digital Still
Camera Shooting, they will not be
recorded.
Date display
Auto Date Record mode
AUTO DATE RECORD
● Your camcorder automatically
records the date for about 5
seconds after recording is initiated
in the following situations:
• After changing the date.
DEC 25.98
AUTO DATE
Auto date record mode
Time display
• After loading a cassette.
• After Auto Date Record mode is
selected by pressing DATE/TIME.
In this mode, the date is replaced
after 5 seconds with “AUTO DATE”
but this is not recorded.
● Setting the Select Dial to AUTO
LOCK always engages the Auto
Date Record mode, and disables
all other modes.
DEC 25.98
PM10:50:00
Auto date record
executed
Date/Time display
DEC 25.98 PM10:50:00
EN
23
FEATURE:
PURPOSE:
Video Light
To brighten the scene when natural
lighting is too dim.
OPERATION:
1) Set the LIGHT OFF/AUTO/ON
Switch as required:
ON
: Always keeps the light on as
long as the camcorder is
turned on.
AUTO : Automatically turns on the
light when the camcorder
senses insufficient lighting
on the subject.
LIGHT OFF/AUTO/ON
OFF : Turns off the light.
Ⅲ The video light can only be used
with the camcorder’s power on.
Ⅲ It is recommended to set the white
balance (੬ pg. 37) to HALOGEN
mode ( ) when you use the video
light.
Ⅲ When not using the video light,
turn it off to save battery power.
NOTES:
● Even if the battery indicator (
does not blink if the battery pack’s
charge is low, the camcorder may
turn off automatically when you
turn on the video light, or when
you start recording with the video
light turned on.
)
DANGER
Ⅲ The video light can become extremely
hot. Do not touch it either while in
operation or soon after turning it off,
otherwise serious injury may result.
Ⅲ Do not place the camcorder into the
carrying case immediately after using
the video light, since it remains
extremely hot for some time.
Ⅲ When operating, keep a distance of
about 30 cm. (1 ft.) between the video
light and people or objects.
Ⅲ Do not use near flammable or explosive
materials.
● When the LIGHT OFF/AUTO/ON
Switch is set to “AUTO”:
•Depending on the lighting
conditions, the video light may
keep turning on and off. In this
case, manually switch the light
on or off using the LIGHT OFF/
AUTO/ON switch.
•While the Sports or High-Speed
Shutter mode (੬ pg. 27) is
engaged, the light is likely to stay
on.
Ⅲ It is recommended that you consult your
nearest JVC dealer for replacing the
video light.
•While the Twilight mode
(੬ pg. 27) is engaged, the light
will not activate.
VIDEO RECORDING Basic Features (cont.)
24
EN
MODE
Snapshot
SNAPSHOT
This interesting feature lets you record two types of
digital still images that look like photographs onto a tape,
as well as keeping them in the camcorder’s built-in
memory. It is a great way to spice up footage of events
such as parties, weddings and graduations.
SELECT SNAPSHOT MODE
Turn the Select Dial to any position except AUTO
1
2
LOCK, then press the MODE Button to switch from
one mode to the other as shown in the illustration to
the left.
•When the Select Dial is set to AUTO LOCK, it is
not possible to select the Snapshot Mode. Only the
Full image (no display) is available. Go to step 2.
Viewfinder
TAKE SNAPSHOT
P
P (Pin-Up)
Press the SNAPSHOT Button.
No display (Full)
•A still image is recorded onto the tape and into the
camcorder’s built-in memory.
•There are two Picture Modes you can choose from
when storing in the camcorder’s memory: FINE
and STANDARD. The maximum number of shots
you can take varies according to the selected
setting. The selected Picture Mode and remaining
number of shots are displayed on the screen. The
factory-preset is FINE. If you want to change the
setting, perform “Picture Mode Setting” (੬ pg. 47).
SNAPSHOT
Viewfinder
(ex. Pin-Up)
1
2
3
4
5
FINE
Allows you to shoot up to approx. 22 still images.
STD (Standard)
Allows you to shoot up to approx. 44 still images.
If you press during recording . . .
.... first there is a momentary camera shutter-type
blackout together with the sound effect of a
shutter closing, then a still image appears. The
next image starts in the center of a black screen
and wipes in toward the corners. The screen
changes as shown in the illustrations 1 to 5 to
the left and the screens 1 to 5 are recorded
onto the tape in the selected mode. Only the
still image 3 is stored in the built-in memory in
the selected mode, then the camcorder resumes
normal recording.
If you press during Record-Standby mode . . .
.... first there is a momentary camera shutter-type
blackout together with the sound effect of a
shutter closing, then a still image appears. The
scene you are currently aimed at starts in the
center of a black screen and wipes in toward the
corners. The screen changes as shown in the
illustrations 1 to 5 to the left. The screens 1
to 3 are recorded onto the tape in the selected
mode. Only the still image 3 is stored in the
built-in memory in the selected mode, then the
camcorder re-enters the Record-Standby mode.
EN
25
NOTES:
Viewfinder
● Six sample images have been stored in the built-in
memory at the factory.
FINE 12
Remaining number
of shots
If you wish to delete them, first remove the “Protect”
function (੬ pg. 57), then perform the “Delete”
function (੬ pg. 58).
● When the remaining number indicator displays “0”
(blinking), the still image will be recorded onto the tape
but not in the built-in memory. If you wish to store a
still image in the built-in memory, perform the
“DELETE” function in the Menu Screen to remove still
images you do not need (੬ pg. 58).
22
21
1
0
(Blinking)
Pictrue mode display:
FINE or STD (standard)
● The Picture Mode can be switched to either “FINE” or
“STANDARD”. Since the remaining number of shots
available depends on the selected Picture Mode,
switching the Picture Mode will vary this number.
● If the SNAPSHOT Button is pressed with the System
Select Switch set to “D.S.C.”, the still image cannot be
recorded onto the tape, but will be stored in the
camcorder's built-in memory (੬ pg. 46).
● Image data stored in the camcorder’s built-in memory
can be transferred to a Windows® PC or Macintosh®
and saved using the provided image transfer software
(੬ pg. 61). The image data transferred to a personal
computer can also be further processed using Paint
Software.
Pin-Up
A still image on a white
background. A shadow
effect is added to give it
a three dimensional feel.
Full
A still image that
occupies the entire
image field is recorded.
● When a Pin-Up is taken with the Wide mode
(੬ pg. 29) activated, the black bars at the top and
bottom of the screen will disappear.
● When a Snapshot is taken in a dark environment, the
still image recorded onto the tape and stored in
memory will become coarse and its true colors will be
lost.
VIDEO RECORDING Advanced Features
26
EN
1 second later, the mode is activated.
Program AE With Special Effects
All you have to do to access any of the variety of
shooting effects is to turn the Select Dial.
After 1 sec.
SEPIA
SELECT MODE
Turn the Select Dial until the symbol of the function
1
you want is aligned with the mark.
•The selected mode’s name and its indication are
displayed for approx. 1 second. Then the name
disappears, and only the indication remains. The
mode is activated.
Viewfinder
•When Auto Mode Lock or Auto Mode Release
mode is selected, only the mode’s name is
displayed. Then the name disappears and the
mode is activated.
NOTES:
● Only one effect can be engaged at a time.
● The screen becomes slightly reddish when the Fade/
Wipe (੬ pg. 28) is used in the Sepia mode.
● The screen becomes slightly dark in the High Speed
Shutter mode. Use in well-lit situations.
● In the High Speed Shutter or Sports modes, picture
color may be adversely affected if subject is lit by
alternating discharge-type light sources such as
flourescent or mercury-vapor lights.
Mark
C
U
EFFECT
WIDE
TITLE
SUPER
LOLUX
Select Dial
EN
27
Dial
symbol
Viewfinder
indication
Dial
symbol
Viewfinder
indication
Mode
Mode
LOCK
AUTO LOCK
Auto Mode Lock
TWILIGHT
Twilight
Auto Mode Lock
Twilight
Locks the camcorder in Full Auto mode, preventing
incorrect operation due to accidental button
pressing during shooting.
Dusk, twilight scenery, fireworks, etc., look more
natural and dramatic. The following happens when
Twilight mode is selected:
•In this mode the following controls are disabled;
DATE/TIME display select, and the Menu Jog Dial.
•Auto gain control is turned off.
•White Balance is set to “ ” (FINE day mode), but
can also be manually changed to another mode
(੬ pg. 37).
RELEASE AUTO RELEASE Auto Mode Release
•Auto Focus becomes available only in the range of
10 m (33 ft.) to infinity. To focus when the subject-
to-camera distance is less than 10 m (33 ft.), use
manual focusing (੬ pg. 35).
Auto Mode Release
Re-enables the controls that were disabled by Auto
Mode Lock.
SPORTS
Sports
Electronic
Fog Filter
FG
FG : FOG
Sports
Electronic Fog Filter
High shutter speed clearly captures fast-moving
action.
Makes the picture look misty white, as when an
external fog filter is attached to the lens. Softens the
image and gives it a “fantasy” look.
NEGA POSI
Nega/Posi
ND
ND:ND EFFECT
ND Effect
Nega/Posi (Negative/Positive)
The colors of a picture are reversed.
ND Effect
A black mist darkens the picture, as when an ND
filter is used. Helps to counter the effects of glare on
the subject.
SEPIA
Sepia
NEGA POSI mode
Sepia
The scene being shot is recorded in sepia-tinted
(reddish-brown) monochrome, giving the effect of
an older movie. Use together with Wide (੬ pg. 29)
for the authentic look of a classic Hollywood
movie.
1/2000 sec.
1/2000
2S 1/2000
High Speed Shutter
High-Speed Shutter (1/2000s.)
Captures faster action than Sports mode.
VIDEO RECORDING Advanced Features (cont.)
28
EN
Fade/Wipe
[Ex. : Fader]
Fade-in
These effects let you make pro-style scene transitions.
Fade- or wipe-in works at recording start, and fade- or
wipe-out works at recording end or when you enter
Record–Standby mode.
ENGAGE FADE- OR WIPE-
STANDBY MODE
Fade-out
Press EFFECT to cycle through the modes as shown
1
at left. Once the desired mode appears, it is selected
and reserved.
Function indication
Viewfinder
4EFFECT
•The selected mode’s name and its indication are
displayed for approx. 2 seconds. Then the name
disappears, and only the indication remains.
MOSAIC
START OR END RECORDING
Press Recording Start/Stop Button to activate fade-in/
out or wipe-in/out.
2
3
After 2 sec.
TO CANCEL FADE- OR WIPE-
STANDBY MODE
BK
BK
FADER
MOSAIC
SHUTTER
SLIDE
Press EFFECT repeatedly until “OFF” appears
.
•“OFF” is displayed for approx. 2 seconds and the
fade/wipe-standby mode is canceled.
OFF
(No indication)
OFF
FADER
Fades in/out to a black screen.
B
K
MOSAIC (Fader)
Gradually turns/returns the picture into/from a mosaic
pattern.
SHUTTER (Wipe)
A black screen moves in from the top and bottom,
closing over the image like a shutter, or a new image
pushes open the black screen vertically from the center.
SLIDE (Wipe)
A black screen moves in from the left to gradually cover
the image, or a new image moves in from right to left.
EFFECT
NOTES:
Recording
Start/Stop
Button
● Pressing and holding the Recording Start/Stop Button
allows you to record a black blank screen or a mosaic
pattern if Mosaic Fader is selected.
● The screen becomes slightly reddish when the Fade/
Wipe is used with Sepia (੬ pg. 27).
● With the Electronic fog filter mode (੬ pg. 27) engaged,
when Fader (not Mosaic) is used, the image fades in/out
to a white screen.
● Even if you start shooting with the Fade/Wipe indication
displayed during Digital Still Camera Shooting, the Fade/
Wipe does not function.
EN
29
Viewfinder
Wide
This feature allows you to record black bars at the top
and bottom of the screen to produce a cinema-like
“wide-screen” effect.
ENGAGE WIDE MODE
Wide mode
Press WIDE.
1
•To restore normal screen, press WIDE again.
Super LoLux(Gain Up)
Bright, natural recordings can be taken even in areas with
low or poor lighting.
SELECT SUPER LOLUX MODE
Press SUPER LOLUX repeatedly to cycle through the
modes as shown at left. Once the desired mode
appears, it is engaged.
1
•The mode’s name is displayed for approx. 2
seconds, then disappears.
WIDE
SUPER LOLUX
MAX : To record a subject in a dark lit environ-
ment. When it is more convenient to shoot
the subject with a brighter image even if
the picture becomes slightly coarse.
NORM : To record a subject in a dimly lit environ-
ment. When it is more convenient to shoot
with a less coarse picture although the
subject becomes slightly dark. This setting
is suitable for measuring sensitivity
Viewfinder
4S.LX
After 2 sec.
MAX
conforming to EIA-639 (EIA* Standard for
Low Light Sensitivity Measurement).
*EIA : Electronic Industries Association
: Allows you to shoot dark scenes with no
picture brightness adjustment.
OFF
MAX
NORM
OFF
NOTE (for Fade/Wipe, Wide, Super LoLux, Instant Titles and Picture Stabilizer) :
When the Select Dial is turned to AUTO LOCK, the above functions will be set to the Factory settings
(Fade/Wipe-standby : “OFF”, Wide mode : off, Super LoLux : “MAX”, Instant Title : off, Picture Stabilizer:
off). Then when the Select Dial is returned to any position except AUTO LOCK, the above functions
return to the settings you selected before turning it to AUTO LOCK. However, if the function is switched
during AUTO LOCK, the selected mode will be set and will remain unchanged even when the Select
Dial is turned to any position except AUTO LOCK.
VIDEO RECORDING Advanced Features (cont.)
30
EN
Viewfinder
Instant Titles
The camcorder has eight preset titles in memory. You can
superimpose one of them above a previously stored title
as shown in the illustration to the left.
Instant Titles can be displayed not only in English but also in
French, Spanish and Portuguese. Change the setting in
TITLE LANG. in the Menu screen. (੬ pg. 31, 33).
Title display
HAPPY BIRTHDAY
OUR VACATION
No display
SELECT PRESET TITLE
Press TITLE repeatedly to cycle through the preset
1
titles until the desired title is displayed.
MERRY CHRISTMAS
A SPECIAL DAY
NOTE:
Even if you shoot with the Title displayed during Digital
Still Camera Shooting, this is not recorded.
HAPPY HOLIDAYS
OUR NEW BABY
WEDDING DAY
CONGRATULATIONS
TITLE
EN
31
Using Menu For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
ACCESS MENU SCREEN
Turn the Select Dial to any position except AUTO
LOCK, then press the MENU Jog Dial. The Menu
Screen appears.
1
2
Select Dial
MENU Jog Dial
SELECT FUNCTION
Rotate the MENU Jog Dial to place the highlight bar
on the desired function.
Viewfinder
MENU
•When the highlight bar reaches the bottom of
Menu Screen 1, Menu Screen 2 is automatically
displayed. When the highlight bar reaches the top
of Menu Screen 2, Menu Screen 1 is automatically
displayed.
4
MENU END
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T30
M. W. B.
AUTO
•If the setting you want can’t be found in the Menu
Screen, place the highlight bar on “MENU END”,
then go to step 5.
ZOOM SPEED FAST
4NEXT
Menu Screen 1
MAKE SETTING
Press the MENU Jog Dial. The setting menu of the
selected function appears. The setting procedure
depends on the function you select.
4
BACK
3
REC TIME
INT. TIME
OFF
OFF
TALLY LAMP ON
If you select “FOCUS”, “EXPOSURE”, or
“DATE/ TIME” . . .
.... see respective pages (FOCUS: ੬ pg. 34, 35,
EXPOSURE: ੬ pg. 36, DATE/TIME: ੬ pg. 13).
TITLE LANG.
D. ZOOM
ENGLISH
ON
OFF
07
COLOR BAR
JLIP ID NO.
DEMO MODE OFF
4
MENU END
If you select “JLIP ID NO.” . . .
Menu Screen 2
.... press the MENU Jog Dial so that the number
blinks, then rotate it until the desired number
appears, and press it. Then rotate the MENU Jog
Dial to move the highlight bar to “EXIT”.
TITLE LANG.
ENGLISH
FRENCH
If you select any other functions . . .
.... rotate the MENU Jog Dial to move the highlight
bar to the desired setting.
SPANISH
PORTUGUESE
•If you decide you want to return to the
previous setting, rotate the MENU Jog Dial to
move the highlight bar to “EXIT”.
EXIT
Setting Menu
(ex. TITLE LANG.)
END SETTING
Press the MENU Jog Dial. The Menu Screen
4
5
reappears and the highlight bar is on “MENU END”.
BACK
4
REC TIME
OFF
OFF
CLOSE MENU
INT. TIME
Press the MENU Jog Dial. The normal screen
reappears.
TALLY LAMP ON
TITLE LANG.
D. ZOOM
FRENCH
ON
OFF
07
COLOR BAR
JLIP ID NO.
DEMO MODE OFF
4MENU END
NOTE:
The menu function except “FOCUS” and “EXPOSURE”
are not available while in the Record mode.
Normal Screen
VIDEO RECORDING Advanced Features (cont.)
Menu Screen Explanations
32
EN
FOCUS
AUTO
MANU
AUTO
MANU
Adjusts focus automatically.
Allows you to adjust focus manually (੬ pg. 34, 35).
Adjusts exposure automatically.
EXPOSURE
Allows you to adjust exposure manually (੬ pg. 36).
DATE/TIME
Allows you to set the current date and time (੬ pg. 13).
TELE MACRO
Usually the distance to a subject where the lens is in focus
OFF
ON
depends on the zoom magnification. Unless there is a distance
more than 1m (3.3 ft.) to the subject, the lens is out of focus at
the maximum telephoto setting. When set to “ON”, you can
shoot a subject as large as possible at a distance of approx. 60
cm (2 ft.).
•Depending on the zoom position, the lens may go out of focus.
TAPE LENGTH
M.W.B.
Allows you to set the tape length depending on the tape used (੬ pg. 16).
AUTO
: FINE
This camcorder’s Automatic Color Temperature system senses
the color temperature of the ambient lighting for automatic
white balance adjustment. However, precise color adjustment is
not possible under the following conditions:
: CLOUD
•When an object is in various shades of the same color.
•When a predominantly red or brown object is being shot
outdoors.
In these cases, use the camcorder’s built-in preset filters for
white balance adjustment (੬ pg. 37).
: HALOGEN
MWB
ZOOM SPEED
Allows you to set the zooming speed (੬ pg. 20).
FAST
SLOW
EN
33
REC TIME
INT. TIME
This feature allows you to set the parameters for Animation and Time-Lapse
recording (੬ pg. 39).
This feature allows you to set the parameters for Self-Timer (੬ pg. 38) and Time-
Lapse recording (੬ pg. 39).
TALLY LAMP
ON
The tally lamp comes on to signal the start of recording.
The tally lamp remains off at all times.
OFF
TITLE LANG.
D. ZOOM
Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)
of Instant Titles (੬ pg. 30)
ON
Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 22 times (the
optical zoom limit), to a maximum of 44 times digital magnifi-
cation.
OFF
Digital Zoom is not available. Only optical zoom (maximum
22x magnification) can function. When set to “OFF” during
Digital Zoom, zoom magnification changes to 22x.
COLOR BAR
Does not display color bars. Normal screen is recorded.
OFF
ON
Makes the normal screen disappear, then displays color bars. By
recording color bars at the beginning or end of a tape, an effect
similar to professional productions can be given to your tape.
NOTE:
While the color bars are displayed, the camcorder’s other
functions are disabled.
JLIP ID NO.
This number is necessary when connecting the camcorder to a device such as a
computer using the J terminal (JLIP). The numbers range from 01 to 99. Factory
setting is 07.
Automatic demonstration will not take place.
DEMO MODE
OFF
ON
Demonstrates certain functions such as Fade/Wipe, Instant Titles
etc. When “DEMO MODE” is set to “ON” and the Menu Screen
is closed, demonstration starts.
NOTES:
● When a tape whose Erase Protection tab is in the position that
allows recording is loaded in the camcorder, demonstration is
not available.
● By turning off the camcorder or inserting a tape whose Erase
Protection tab is in the position that allows recording into it,
“DEMO MODE” is set to “OFF” automatically.
● During demonstration, all functions except zoom are disabled.
= Factory setting and when the Select Dial is set to AUTO LOCK
VIDEO RECORDING Advanced Features (cont.)
34
EN
Focusing
Auto Focus
Focus
detection zone
The camcorder’s Full Range AF system offers continuous
shooting ability from close-up to infinity. However,
correct focus may not be obtainable in the situations
listed below (in these cases use manual focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-color wall,
or a clear, blue sky.*
•When a dark object is barely visible.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast
background.
* The low-contrast warning “
” appears.
NOTES:
● If the lens is smeared or blurred, accurate focusing is
not possible. Keep the lens clean, wiping with a piece
of soft cloth if it gets dirty. When condensation occurs,
wipe with a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom-out
first (੬ pg. 20). If zoomed-in in the auto focus mode,
the camcorder could automatically zoom out depend-
ing on the distance between the camcorder and the
subject. When Tele Macro (੬ pg. 32) is activated, the
camcorder will not zoom out automatically.
EN
35
Manual Focus
NOTE:
You should already have made the necessary viewfinder
adjustments (੬ pg. 14). If you haven’t, do so before
continuing.
ACCESS MENU SCREEN
Turn the Select Dial to any position except AUTO
1
2
LOCK, then press the MENU Jog Dial. The Menu
Screen appears, and the highlight bar is placed on
“FOCUS”.
Select Dial
MENU Jog Dial
Menu Screen
Viewfinder
ACCESS FOCUS MENU SCREEN
Press the MENU Jog Dial.
MENU
4
MENU END
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
ACCESS MANUAL FOCUS
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T30
Rotate the MENU Jog Dial to move the highlight bar
No indication
during recording
M. W. B.
AUTO
3 to “MANU”, then press it. “ ” and “
” appear. The
ZOOM SPEED FAST
focus is locked at this point.
4
NEXT
ADJUST FOCUS
To farther subject . . .
4 Rotate the MENU Jog Dial upward. “
blinks.
FOCUS
Focus Menu
Screen
” appears and
AUTO
MANU
Go to step 5.
To nearer subject . . .
Rotate the MENU Jog Dial downward. “ ” appears
and blinks.
Go to step 5.
No indication
during recording
EXIT
END ADJUSTMENT OF FOCUS
Press the MENU Jog Dial. The Menu Screen
reappears and the highlight bar is placed on “MENU
END”.
Manual Focus
Screen
5
6
CLOSE MENU
Press the MENU Jog Dial. The Menu Screen
disppears and “
is locked.
” reappears to indicate the focus
NOTES:
● To return to Auto Focus, select “AUTO” in step 3.
● To re-adjust Manual Focus, repeat the procedure from
step 1.
● Be sure to focus the lens in the maximum telephoto
position when you use the Manual Focus mode. If you
focus in on a certain subject in the wide-angle position,
sharply focused images cannot be obtained when
zoomed up because the depth-of-field is reduced at
longer focal lengths.
● When the focus level cannot be adjusted any farther or
closer, “ ” or “ ” will blink.
VIDEO RECORDING Advanced Features (cont.)
36
EN
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override and make
the adjustment manually.
ACCESS MENU SCREEN
Turn the Select Dial to any position except AUTO
LOCK, then press the MENU Jog Dial. The Menu
Screen appears.
1
Select Dial
MENU Jog Dial
Menu Screen
ACCESS EXPOSURE MENU
SCREEN
Rotate the MENU Jog Dial to move the highlight bar
to “EXPOSURE” and press it.
Viewfinder
MENU
2
3
4
MENU END
ACCESS MANUAL EXPOSURE
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
Rotate the MENU Jog Dial to move the highlight bar
to “MANU”, then press it. “00” (exposure control
level counter) appears.
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T30
No indication
during recording
M. W. B.
AUTO
ZOOM SPEED FAST
4
NEXT
ADJUST EXPOSURE
To brighten the image . . .
4 Rotate the MENU Jog Dial upward. The exposure
control level counter increases (maximum +06).
Go to step 5.
EXPOSURE
Exposure Menu
Screen
AUTO
MANU
To darken the image . . .
Rotate the MENU Jog Dial downward. The exposure
control level counter decreases (maximum –06).
Go to step 5.
No indication
during recording
EXIT
END ADJUSTMENT OF EXPOSURE
Press the MENU Jog Dial. The Menu Screen
5
6
reappears and the highlight bar is placed on “MENU
END”.
00
Exposure
control
level
CLOSE MENU
Press the MENU Jog Dial. The Menu Screen
disappears and the exposure control level counter
reappers to indicate the exposure is adjusted.
counter
NOTES:
Manual Exposure Screen
To brighten the image
● To return to the factory setting, select “AUTO” in step 3.
● To re-adjust exposure, repeat the procedure from
step 1.
–
06
+
06
To darken the image
EN
37
Viewfinder
MENU
Manual White Balance Adjustment
(M.W.B.)
Menu Screen
4
MENU END
The white balance is usually adjusted automatically.
However, the more advanced camcorder operator would
prefer to control this function manually and achieve a
more professional color/tint reproduction.
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T30
M. W. B.
AUTO
ZOOM SPEED FAST
ACCESS MENU SCREEN
4
NEXT
Turn the Select Dial to any position except AUTO
LOCK, then press the MENU Jog Dial. The Menu
1
Screen appears.
M. W. B.
M.W.B.
Menu Screen
AUTO
ACCESS WHITE BALANCE MENU
: FINE
: CLOUD
SCREEN
: HALOGEN
MWB
Rotate the MENU Jog Dial to move the highlight bar
to “M.W.B.”, then press it.
2
EXIT
SELECT WHITE BALANCE
Rotate the MENU Jog Dial to move the highlight bar
to the required white balance.
3
“AUTO” ................... Automatic adjustment
“
“
“
: FINE” ............. Outdoors on sunny day
: CLOUD” ........ Outdoors on cloudy day
: HALOGEN” ... Light source is halogen or
tungsten lamp
“MWB” .................... When using a personal White
Balance Setting stored in
memory (see below.)
CLOSE MENU
Press the MENU Jog Dial. The Menu Screen
reappears. Then press the MENU Jog Dial again to
exit the Menu Screen.
Select Dial
4
MENU
Jog Dial
MWB
MWB sets the color temperature for the subject’s light
source so you can shoot with natural colors that are
unaffected by surroundings, even when there are
multiple subjects with different color temperatures.
NOTES:
● To switch to automatic white balance
adjustment, set the M.W.B. in the Menu
Screen to “AUTO”, or turn the Select Dial to
“AUTO LOCK”.
PREPARE WHITE OBJECT
Point the camcorder at a white, flat object such as a
● Re-adjust the White Balance when the
lighting has changed, when the camcorder
has been turned off and on again, or when
the Select Dial’s position has been changed.
● When adjusted by putting colored paper in
front of the subject in step 1 of “MWB”, this
unit makes its color temperature standard for
automatic white balance. So you can enjoy
shooting with different colors. For example,
when adjusting with red, blue or yellow
colors, the image becomes the color which
approximates to green, orange or purple
respectively.
1
2
3
sheet of white paper.
SELECT MWB
Follow step 1 through 3 of the above, select
“MWB”.
MEMORIZE WHITE BALANCE
Press the MENU Jog Dial until “MWB” begins
blinking. “MWB” blinks while the white balance is
being stored in memory, then the Menu Screen
reappears when memorization is complete.
CLOSE MENU
● It is helpful to connect your camcorder to a
color monitor when adjusting the white
balance (੬ pg. 44).
Press the MENU Jog Dial.
4
VIDEO RECORDING Advanced Features (cont.)
38
EN
Self-Timer
Recording
Start/Stop Button
You can set the delay between pressing the Recording
Start/Stop Button and the actual start of recording. If you
secure the camcorder, you (or whomever is operating the
camcorder) can enter the scene before recording starts.
NOTE:
Make sure the camcorder is in the Record-Standby mode
before performing the following steps.
ACCESS MENU SCREEN
Turn the Select Dial to any position except AUTO
1
2
3
LOCK, then press the MENU Jog Dial.
Select Dial
MENU Jog Dial
Menu Screen
ACCESS INT. TIME MENU SCREEN
Rotate the MENU Jog Dial to move the highlight bar
to “INT. TIME”, then press the MENU Jog Dial.
System Select Switch
Viewfinder
MENU
SET INTERVAL TIME
4
MENU END
Rotate the MENU Jog Dial to move the highlight bar
to the desired time, then press the MENU Jog Dial.
The Menu Screen reappears and the highlight bar is
placed on “MENU END”.
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
TAPE LENGTH T30
M. W. B.
AUTO
ZOOM SPEED FAST
CLOSE MENU
4
NEXT
Press the MENU Jog Dial.
4
5
4
BACK
START DELAYED RECORDING
If you set the System Select Switch to “VIDEO” . . .
Press the Recording Start/Stop Button. When the
selected time has elapsed, recording begins
automatically.
REC TIME
INT. TIME
OFF
OFF
TALLY LAMP ON
TITLE LANG.
D. ZOOM
ENGLISH
ON
OFF
07
COLOR BAR
JLIP ID NO.
DEMO MODE OFF
If you set the System Select Switch to “D.S.C.” . . .
Press the SNAPSHOT Button. When the selected
time has elapsed, a still image is shot automatically.
4
MENU END
INT. TIME
REC TIME
To Cancel Self-Timer . . .
OFF
OFF
If you set the System Select Switch to “VIDEO” . . .
15 S
1 4 S
1 2 S
1 S
30 S
.... Before the recording begins, press the Recording
1 MIN
5 MIN
Start/Stop Button to display “
”, then set
PAUSE
5 S
“INT. TIME” in the Menu Screen to “OFF”.
If you set the System Select Switch to “D.S.C.” . . .
.... Before shooting a still image, press the SNAPSHOT
Button, then set “INT.TIME” in the Menu Screen to
“OFF”.
EXIT
EXIT
INT. TIME Menu
REC TIME Menu
INT. TIME Indicator
INT. TIME and
REC TIME
indications on the
normal screen
15S
1S
REC TIME Indicator
EN
39
Animation
Time-Lapse
Give stationary scenes or objects an illusion of
movement. This function allows you to shoot a
series of pictures, each slightly different, of the same
object for a brief period of time.
You can record sequentially at preset time spans.
Leaving the camcorder aimed at a specific subject,
you can record subtle changes over an extended
period of time.
NOTE:
NOTE:
Make sure the camcorder is in the Record-Standby
mode and the recording mode is set to “SP” before
performing the following steps.
Make sure the camcorder is in the Record-Standby
mode and the recording mode is set to “SP” before
performing the following steps.
ACCESS MENU SCREEN
ACCESS MENU SCREEN
Turn the Select Dial to any position except
Turn the Select Dial to any position except
1
2
AUTO LOCK, then press MENU Jog Dial.
1
2
AUTO LOCK, then press MENU Jog Dial.
SET RECORDING TIME
SET INTERVAL BETWEEN
Rotate the MENU Jog Dial to move the
highlight bar to “REC TIME”, then press the
MENU Jog Dial. The REC TIME Menu appears.
Rotate the MENU Jog Dial to move the
highlight bar to the desired time, then press the
MENU Jog Dial. The Menu Screen reappears.
Press the MENU Jog Dial again to exit the
Menu Screen.
RECORDINGS
Rotate the MENU Jog Dial to move the
highlight bar to “INT. TIME”, then press the
MENU Jog Dial. The INT. TIME Menu appears.
Rotate the MENU Jog Dial to move the
highlight bar to the desired time, then press the
MENU Jog Dial. The Menu Screen reappears.
SET RECORDING TIME
START RECORDING
Rotate the MENU Jog Dial to move the
highlight bar to “REC TIME”, then press the
MENU Jog Dial. The REC TIME Menu appears.
Rotate the MENU Jog Dial to move the
highlight bar to the desired time, then press the
MENU Jog Dial. The Menu Screen reappears.
Press the MENU Jog Dial again to exit the
Menu Screen.
Press the Recording Start/Stop Button after
focusing on the subject. The recording stops
automatically after the selected period of time.
3
3
ASSEMBLE SERIES OF
PICTURES
Repeat step 3 for the desired number of
pictures.
4
5
START TIME-LAPSE
RELEASE ANIMATION MODE
RECORDING
Set “REC TIME” in the Menu screen to “OFF”.
Press the Recording Start/Stop Button.
Recording and intervals alternate
automatically.
4
5
NOTES:
RELEASE TIME-LAPSE MODE
● For best results, make sure the camcorder is
secured when shooting in Animation or
Time-Lapse mode.
To release when “
” is displayed, set
PAUSE
“REC TIME” and “INT. TIME” in the Menu
Screen to “OFF”. To release when
” and “REC ” are not displayed,
● Fade- or Wipe-in/out cannot be performed during
Animation or Time-Lapse shooting.
● Before performing other operations following
Animation or Time-Lapse recording, make sure
the Animation or Time-Lapse mode is deactivated.
● Self-Timer, Animation and Time-Lapse are
canceled when the power is shut off or when the
cassette is ejected.
“
PAUSE
press the Recording Start/Stop Button to display
”, then set “REC TIME” and “INT.
TIME” in the Menu Screen to “OFF”.
“
PAUSE
VIDEO PLAYBACK Basic Playback
40
EN
Tape running indicator
LOAD A CASSETTE
Slide EJECT to open the cassette holder, then insert
4
: Playback
1
2
the cassette with the label facing out. Press PUSH to
3
2
: Fast-Forward/Forward Search
: Rewind/Reverse Search
ensure the holder is closed and locked.
6 : Still Playback
SELECT MODE
Set the System Select Swtich to “VIDEO”, then set
the Power Switch to “PLAY”. The power indicator
lights.
4
Tape counter
M–0:23:45
PLAY BACK
PLAY/PAUSE
REW
Press PLAY/PAUSE. The playback picture appears.
3
4
STOP PLAYBACK
Press STOP.
FF
STOP
Rewind or Fast-forward the tape
Press REW to rewind, or FF to fast-forward the tape
during Stop mode.
NOTE:
The camcorder shuts off automatically after about 5
minutes in Stop mode. To turn on again, set the Power
Switch to “POWER OFF”, then to “PLAY”.
System Select Switch
VIDEO PLAYBACK Features
EN
41
Tracking
AT
This function can be used to eliminate noise bars that
appear on-screen during playback. Initial setting is Auto
Tracking. Manual Tracking is also available.
ACTIVATE MANUAL TRACKING
Press the MENU Jog Dial during playback mode.
1
Keep rotating it until noise bars disappear.
•To return to Auto Tracking, press the MENU Jog
Dial. “AT” blinks. When Auto Tracking finishes,
the indication disappears.
NOTES:
● When noise bars appear during playback, the
camcorder enters the Auto Tracking mode and “AT” is
displayed.
● Manual Tracking may not work with tapes recorded on
other VCRs or camcorders.
MENU Jog Dial
VIDEO PLAYBACK Features (cont.)
42
EN
FEATURE:
Still Playback
PURPOSE:
OPERATION:
To pause during playback.
1) Press PLAY/PAUSE during
playback.
2) To resume normal playback, press
PLAY/PAUSE again.
COUNTER R/M
PLAY/PAUSE
NOTE:
Noise bars appear and pictures may
become monochrome during Still
Playback. This is normal.
REW
FF
STOP
FEATURE:
PURPOSE:
Shuttle Search
To allow high-speed search in either
direction.
OPERATION:
Forward Search
1) Press FF during playback.
Reverse Search
1) Press REW during playback.
Noise bars appear and pictures may
become monochrome or darken in
Shuttle Search. This is normal.
NOTE:
FEATURE:
PURPOSE:
Counter Memory Function
To make it easier to locate a specific
tape segment.
Set to “VIDEO”
OPERATION:
1) Press COUNTER R/M and hold for
more than 1 second. The counter
resets to “0:00:00”.
2) Press COUNTER R/M for less than
1 second. “M” appears.
3) After recording or playback, press
STOP, then REW. The tape
automatically stops at or close to
0:00:00.
4) Press PLAY/PAUSE to start
playback.
NOTES:
● The counter memory functions in
the Fast-Forward and Rewind
modes.
● To disable Counter Memory
Function, press COUNTER R/M for
less than 1 second so the “M”
disappears.
VIDEO PLAYBACK Using The Cassette Adapter
Cassette Adapter (VHS Playpak)
EN
43
Use this to play back a VHS-C video cassette recorded
with this camcorder. It is fully compatible with any VHS
video cassette recorder. The C-P7U adapter is battery
powered and automatically performs tape loading and
unloading.
INSERT BATTERY
Slide the battery cover up to remove it, and install
one “AA(R6)” size battery as shown in the
illustration at left. Then reattach the cover.
1
2
3
VCR
INSERT CASSETTE IN ADAPTER
Slide the latch to open the adapter compartment
door, then insert the cassette and close the
compartment door.
Compartment door
PLAY BACK ON CONNECTED VCR
Load the cassette adapter into the VCR and play the
tape back as you would any other.
REMOVE CASSETTE FROM
ADAPTER
Slide the latch and the compartment door opens
automatically. This may take around 10 seconds. Do
not attempt to force the adapter open. Then insert
your finger in the hole on the underside of the
adapter as shown in the illustration at left, push up
and remove the cassette.
4
Sliding latch
Reels
Compact video cassette
NOTES:
● During tape loading and unloading, do not touch the
reels for safety and tape protection.
● During special-effect playback (slow motion, still
frame, etc.), the picture may vibrate or noise bars may
appear on the screen.
● To record on a VCR using a compact cassette and the
adapter, cover the adapter’s recording safety hole with
adhesive tape.
Recording safety hole
BASIC CONNECTIONS TO VCR
There are three basic types of connections. When making
the connections, refer also to your VCR and TV
instruction manuals.
44
EN
A
Connection To A VCR
(Editing, Dubbing and Playback)
When
NOTE:
connecting the
cables, open
Use the optional Audio and Video cables.
To AUDIO and
VIDEO OUT
connectors
the jack cover.
CONNECT CAMCORDER TO VCR
As shown in the illustration at left, connect the
1
Audio and Video cables between the AUDIO and
VIDEO OUT connectors on the camcorder and
those on the VCR.
Audio and
Video cables
(optional)
To
SUPPLY POWER
AUDIO and
VIDEO IN
connectors
Turn on the camcorder, the VCR and the TV.
2
3
SELECT MODE
Set the VCR to its AUX input mode, and set the TV
to its VIDEO mode.
VCR
Antenna
Connection To A TV With A/V Input
B
Connectors (Playback ONLY)
NOTE:
Use the optional Audio and Video cables.
RF unit
RF-V5U
(optional)
CONNECT CAMCORDER TO TV
As shown in the illustration at left, connect the
1
2
Audio and Video cables between the AUDIO and
VIDEO OUT connectors on the camcorder and
those on the TV.
To AUDIO, VIDEO and
RF DC OUT connectors
SELECT MODE
Set the TV to its VIDEO or AV mode (as specified in
its instructions).
NOTES:
● It is recommended to use the AC Power
Adapter/Charger as the power supply instead
of the battery pack.
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power Switch to “CAMERA”,
then set your TV to the appropriate input
mode.
● If you have a TV or speakers that are not
specially shielded, do not place the speakers
adjacent to the TV as interference will occur
in the camcorder playback picture.
Connection To A TV With NO A/V Input
Connectors (Playback ONLY)
NOTE:
Use the optional RF-V5U RF unit.
*Refer to the RF-V5U instruction manual for connection
procedure.
TAPE DUBBING
EN
45
Tape Dubbing
CONNECT EQUIPMENT
Following the illustration at left, connect the
camcorder and the VCR.
1
2
PLAY/PAUSE
PREPARE FOR DUBBING
Set the camcorder’s Power Switch to “PLAY”. Turn
on the VCR’s power, and insert the appropriate
cassettes in the camcorder and the VCR.
SELECT VCR MODE
Engage the VCR’s AUX and Record-Pause modes.
3
4
FIND EDIT-IN POINT
Engage the camcorder’s Play mode to find a spot
just before the edit-in point. Once it’s reached, press
PAUSE on the camcorder.
Power Switch
START EDITING
When connecting
the cables, open
the jack cover.
Press PLAY on the camcorder and engage the VCR’s
Record mode.
To AUDIO and
VIDEO OUT
connectors
5
6
7
STOP EDITING TEMPORARILY
Engage the VCR’s Record-Pause mode and press
PAUSE on the camcorder.
Audio and
Video cables
(optional)
EDIT MORE SEGMENTS
Repeat steps 4 through 6 for additional editing, then
stop the VCR and camcorder when finished.
To AUDIO and
VIDEO IN
connectors
VCR
(Recording deck)
DIGITAL STILL CAMERA (D.S.C.) SHOOTING
46
EN
Set to “D.S.C.”
Basic Shooting
MODE
SNAPSHOT
When shooting a still image, it is not recorded onto the
tape, but it is stored in the camcorder's built-in memory
in the selected Picture Mode. A stored still image data
can be transferred to a PC, saved, and processed using a
Paint Software program (੬ pg. 61). A still image
processed on the PC can be also inserted onto a tape
(੬ pg. 69).
SELECT MODE
Slide the LENS COVER Open/Close Switch to open
the lens cover, then set the System Select Switch to
“D.S.C.”. Set the Power Switch to “CAMERA”.
1
2
•The power indicator lights and an image appears.
P
SELECT PICTURE MODE
P (Pin-Up)
No display (Full)
Set “PICTURE” to “FINE” or “STANDARD” in the
Menu Screen (੬ pg. 47) as required.
To select in the Full Auto mode . . .
.... turn the Select Dial to AUTO LOCK. Go to step 4.
Viewfinder
To shoot using various functions . . .
.... turn the Select Dial to any position except
AUTO LOCK. Go to step 3.
Pin-Up
A still image on a white
background. A shadow
effect is added to give it
a three dimensional feel.
•There are two modes: FINE allows you to shoot up
to approx. 22 still images with higher resolution,
and STANDARD allows you to shoot up to approx.
44 still images with lower resolution.
SELECT SNAPSHOT MODE
Full
Press the MODE Button to switch from one mode to
the other until the desired setting appears as shown
in the illustration to the left.
A still image that
occupies the entire
image field is stored.
3
4
SHOOT
Press the SNAPSHOT Button.
•A still image is stored in the built-in memory and
displayed for approx. 2 seconds. While the still
image remains displayed, that image is in the
process of being stored in memory, and it is
therefore impossible to take another shot during
that time. When the still image disappears and the
scene you are currently aimed at appears on the
screen, you may take another shot.
Pictrue mode display
FINE 12
Remaining number
of shots
22
21
1
0
•The remaining number of shots available is
displayed.
(Blinking)
NOTES:
● The remaining number of shots varies according to the
selected Picture Mode. In the “STANDARD” mode,
twice as many still images can be shot as in the “FINE”
mode.
● Six sample images have been stored in the built-in
memory at the factory.
If you wish to delete them, first remove the “Protect”
function (੬ pg. 57), then perform the “Delete”
function (੬ pg. 58)
EN
47
Set to “D.S.C.”
FEATURE:
PURPOSE:
Picture Mode Setting
There are two image settings you can
choose from when storing in the
camcorder’s memory: FINE and
STANDARD. You can select either
according to your needs.
OPERATION:
1) ACCESS MENU SCREEN
Turn the Select Dial to any
position except AUTO LOCK.
Press the MENU Jog Dial.
2) SELECT FUNCTION
Rotate the MENU Jog Dial to move
the highlight bar to “PICTURE”,
then press it. The Picture Mode
Setting Menu appears.
Select Dial
MENU Jog Dial
Menu Screen
3) SET PICTURE MODE
Viewfinder
MENU
Rotate the MENU Jog Dial to move
the highlight bar to the desired
setting (FINE or STANDARD).
Ⅲ Factory-preset is “FINE”.
Ⅲ If you want the Picture Mode to
return to the previous setting,
rotate the MENU Jog Dial to
move the highlight bar to “EXIT”.
4) CLOSE MENU
4
MENU END
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
PICTURE
M. W. B.
FINE
AUTO
ZOOM SPEED FAST
4
NEXT
Press the MENU Jog Dial. The
Menu Screen reappears and the
highlight bar is on “MENU END”.
Then press the MENU Jog Dial
again to close the Menu Screen.
“STD” is displayed with STAND-
ARD selected, and “FINE” is
displayed with FINE selected.
PICTURE
Picture Mode
Setting Menu
FINE
STANDARD
EXIT
NOTES:
● To store the still images you shot, we recommend that you transfer them to a computer and save them
on disk (੬ pg. 61).
● When the remaining number indicator displays “0” (blinking), it is not possible to continue storing
pictures until you delete some shots to make room for new ones. Perform “DELETE” function in the
Menu Screen to remove pictures you do not need (੬pg. 58).
● The Picture Mode can be switched to either “FINE”or “STANDARD”. Since the remaining number of
shots available depends on the selected Picture Mode, switching the Picture Mode will vary this
number.
● The LENS COVER warning blinks for approx. 5 seconds when the camcorder is turned on when the
cover is closed.
● When the SNAPSHOT Button is pressed with the System Select Switch set to “VIDEO”, the picture is
stored not only in the camcorder's built-in memory but also onto the tape (if a tape is in the camcorder)
(੬ pg. 24).
● When you shoot in a dark environment, the still image will become coarse and its true colors will be
lost.
D.S.C. SHOOTING Advanced Features
During Digital Still Camera shooting, various functions used for movie shooting are also available. After
setting the following functions, press the SNAPSHOT Button to shoot. A still image which takes advantage of
these movie functions is stored in memory.
48
EN
Mode
Function
Zoom
Allows you to use the optical zoom or the Digital Zoom. Zooming is possible
from 22 times (the optical zoom limit), to a maximum of 44 times digital magnifi-
cation. Select optical zoom or Digital Zoom in the Menu Screen (੬ pg. 50).
Picture
Stabilizer
When recording while holding the camorder in your hand, or when shooting a
subject with little or no contrast, subtle hand movements will cause shakiness in
the recorded image (੬ pg. 21).
Video Light
To brighten the scene when natural lighting is too dim (੬ pg. 23).
Auto Mode Lock
Locks the camcorder in Full Auto mode, preventing incorrect operation due to
accidental button pressing during shooting.
•In this mode the following controls are disabled; DATE/TIME display select, and
the Menu Jog Dial (੬ pg. 26, 27).
Auto Mode
Release
Re-enables the controls that were disabled by Auto Mode Lock (੬ pg. 26, 27).
Makes the picture look misty white, as when an external fog filter is attached to
the lens. Softens the image and gives it a “fantasy” look (੬ pg. 26, 27).
Electronic Fog
Filter
ND Effect
A black mist darkens the picture, as when an ND filter is used. Helps to counter
the effects of glare on the subject (੬ pg. 26, 27).
Sepia
Allows you to shoot a still image in monochrome, giving the effect of an older
picture (੬ pg. 26, 27).
EN
49
Mode
Function
Twilight
Dusk, twilight scenery, fireworks, etc., look more natural and dramatic. The
following happens when Twilight mode is selected (੬ pg. 26, 27):
•Auto gain control is turned off.
•White Balance is set to “ ” (FINE day mode), but can also be manually
changed to another mode.
•Auto Focus becomes available only in the range of 10 m (33 ft.) to infinity. To
focus when the subject-to-camera distance is less than 10 m (33 ft.), use manual
focusing (੬ pg. 35).
Sports
High shutter speed clearly captures fast-moving action (੬ pg. 26, 27).
Nega/Posi
(Negative/
Positive)
The colors of a picture are reversed (੬ pg. 26, 27).
1/2000 sec. High
Speed Shutter
Captures faster action than Sports mode (੬ pg. 26, 27).
Wide
Black bars are recorded at the top and bottom of the screen to produce a cinema-
like “wide-screen” effect (੬ pg. 29).
Super LoLux
(Gain Up)
Bright, natural recordings can be taken even in areas with low or poor lighting
(੬ pg. 29).
Self-Timer
Once the camcorder is set, the camcorder operator can become part of the scene
in a more natural way adding the final touch to a memorable picture.
•Perform steps 1 through 4 on pg. 38, then press the SNAPSHOT Button as step 5
in place of the Recording Start/Stop Button. When the selected time has elapsed,
a still image is shot automatically (੬ pg. 38).
D.S.C. SHOOTING Advanced Features (cont.)
50
EN
Using Menu For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
ACCESS MENU SCREEN
Turn the Select Dial to any position except AUTO
LOCK, then press the MENU Jog Dial. The Menu
Screen appears.
1
2
Select Dial
MENU Jog Dial
SELECT FUNCTION
Rotate the MENU Jog Dial to place the highlight bar
on the desired function.
Viewfinder
MENU
4
MENU END
•When the highlight bar reaches the bottom of
Menu Screen 1, Menu Screen 2 is automatically
displayed. When the highlight bar reaches the top
of Menu Screen 2, Menu Screen 1 is automatically
displayed.
FOCUS
AUTO
EXPOSURE
DATE TIME
AUTO
DEC 25.98
TELE MACRO OFF
PICTURE
M. W. B.
FINE
AUTO
ZOOM SPEED FAST
•If the setting you want can’t be found in the Menu
Screen, place the highlight bar on “MENU END”,
then go to step 5.
4NEXT
Menu Screen 1
MAKE SETTING
4
BACK
Press the MENU Jog Dial. The setting menu of the
selected function appears. The setting procedure
depends on the function you select. It is not possible
to change “REC TIME” and “TITLE LANG.” settings.
REC TIME
INT. TIME
OFF
OFF
3
TALLY LAMP ON
TITLE LANG.
D. ZOOM
ENGLISH
ON
OFF
06
COLOR BAR
JLIP ID NO.
If you select “FOCUS”, “EXPOSURE” or “DATE/
TIME” . . .
.... see respective pages (FOCUS: ੬ pg. 34, 35,
EXPOSURE: ੬ pg. 36, DATE/TIME: ੬ pg. 13).
DEMO MODE OFF
4
MENU END
Menu Screen 2
If you select “JLIP ID NO.” . . .
.... press the MENU Jog Dial so that the number
blinks, then rotate it until the desired number
appears, and press it. Then rotate the MENU Jog
Dial to move the highlight bar to “EXIT”.
INT. TIME
OFF
15 S
30 S
1 MIN
5 MIN
If you select any other functions . . .
.... rotate the MENU Jog Dial to move the highlight
bar to the desired setting.
EXIT
•If you decide you want to return to the
previous setting, rotate the MENU Jog Dial to
move the highlight bar to “EXIT”.
Setting Menu
(ex. INT. TIME)
END SETTING
Press the MENU Jog Dial. The Menu Screen
4
BACK
4
5
reappears and the highlight bar is on “MENU END”.
REC TIME
INT. TIME
OFF
15 S
TALLY LAMP ON
CLOSE MENU
TITLE LANG.
D. ZOOM
ENGLISH
ON
OFF
06
Press the MENU Jog Dial. The normal screen
reappears.
COLOR BAR
JLIP ID NO.
DEMO MODE OFF
4
MENU END
NOTE:
The menu function except “FOCUS” and “EXPOSURE”
are not available while in the Record mode.
Normal Screen
EN
51
Menu Screen Explanations
FOCUS
AUTO
MANU
AUTO
MANU
Adjusts focus automatically.
Allows you to adjust focus manually (੬ pg. 34, 35).
Adjusts exposure automatically.
EXPOSURE
Allows you to adjust exposure manually (੬ pg. 36).
DATE/TIME
Allows you to set the current date and time (੬ pg. 13).
TELE MACRO
Usually the distance to a subject where the lens is in focus
OFF
ON
depends on the zoom magnification. Unless there is a distance
more than 1m (3.3 ft.) to the subject, the lens is out of focus at
the maximum telephoto setting. When set to “ON”, you can
shoot a subject as large as possible at a distance of approx. 60
cm (2 ft.).
•Depending on the zoom position, the lens may go out of focus.
FINE
Allows you to shoot up to approx. 22 still images in JPEG (Joint
Photographic Expert Group) format. Since the quality of image
is better than “STANDARD”, “FINE” is more suitable for post-
production on a PC.
PICTURE
STANDARD
(STD)
Allows you to shoot up to approx. 44 still images in JPEG (Joint
Photographic Expert Group) format. Since in this mode, twice as
many still images can be shot as in the “FINE” mode, select this
mode when you wish to shoot many still images.
This camcorder’s Automatic Color Temperature system senses
the color temperature of the ambient lighting for automatic
white balance adjustment. However, precise color adjustment is
not possible under the following conditions:
M.W.B.
AUTO
: FINE
: CLOUD
•When an object is in various shades of the same color.
•When a predominantly red or brown object is being shot
outdoors.
In these cases, use the camcorder’s built-in preset filters for
white balance adjustment (੬ pg. 37).
: HALOGEN
MWB
ZOOM SPEED
FAST
Allows you to set the zooming speed (੬ pg. 20).
SLOW
= Factory setting and when the Select Dial is set to AUTO LOCK
CONTINUED ON NEXT PAGE
D.S.C. SHOOTING Advanced Features (cont.)
Menu Screen Explanations (cont.)
52
EN
REC TIME
Setting is impossible.
INT. TIME
This feature allows you to set the parameters for Self-Timer (੬ pg. 38).
TALLY LAMP
ON
The tally lamp comes on to signal the start of recording.
The tally lamp remains off at all times.
OFF
Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)
TITLE LANG.
D. ZOOM
of Instant Titles (੬ pg. 30) .
ON
Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 22 times (the
optical zoom limit), to a maximum of 44 times digital magnifi-
cation.
OFF
Digital Zoom is not available. Only optical zoom (maximum
22x magnification) can function. When set to “OFF” during
Digital Zoom, zoom magnification changes to 22x.
COLOR BAR
OFF
ON
Does not display color bars. Normal screen is recorded.
Makes the normal screen disappear, then displays color bars.
By recording color bars at the beginning or end of a tape, an
effect similar to professional productions can be given to your
tape.
NOTE:
While the color bars are displayed, the camcorder’s other
functions are disabled.
This number is necessary when connecting the camcorder to a device such as a
computer using the J terminal (JLIP). The numbers range from 01 to 99. Factory
setting is 07.
JLIP ID NO.
Automatic demonstration will not take place.
DEMO MODE
OFF
ON
Demonstrates certain functions such as Fade/Wipe, Instant
Titles etc. When “DEMO MODE” is set to “ON” and the Menu
Screen is closed, demonstration starts.
NOTES:
●When a tape whose Erase Protection tab is in the position that
allows recording is loaded in the camcorder, demonstration is
not available.
●By turning off the camcorder, “DEMO MODE” is set to “OFF”
automatically.
●During demonstration, all functions except zoom are
disabled.
= Factory setting and when the Select Dial is set to AUTO LOCK
D.S.C. PLAYBACK Basic Playback
EN
53
Still images shot using this camcoder are automatically
numbered, then stored in numerical order in the built-in
memory. You can view the still images stored in memory,
one at a time, much like flipping through a photo album.
Page Button
SELECT MODE
Set the System Select Switch to “D.S.C.”, then set
1
the Power Switch to “PLAY”.
•The still image stored in memory is displayed.
•When no still image is stored in memory, the
screen becomes blue.
System Select Switch
PLAY BACK
Press “W” or “T” located on the Page Button to
select the still image you want to view.
2
•Each time “W” is pressed, the page goes back,
while each time “T” is pressed, the page goes next.
•Even if you shoot a new picture after playing back
a still image with a low number, this will not
overwrite the existing picture because new
pictures are automatically stored after the still
image most recently stored in memory.
To move the
page next
Viewfinder
NOTES:
● The playback picture can also be viewed on a
connected TV (੬ pg. 44). Camcorder operation is the
same as described in this section.
● When viewing a playback picture on a connected TV,
it may jitter slightly.
To move the
page back
D.S.C. PLAYBACK Advanced Features
54
EN
Using Menu For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
ACCESS MENU SCREEN
Press the MENU Jog Dial. The Menu Screen
1
2
appears.
Select Dial
SELECT FUNCTION
MENU Jog Dial
Rotate the MENU Jog Dial to place the highlight bar
on the desired function.
Viewfinder
•If the setting you want can’t be found in the Menu
Screen, place the highlight bar on “MENU END”,
then go to step 5.
MENU
INDEX
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
MAKE SETTING
DELETE
Press the MENU Jog Dial. The setting menu of the
selected function appears. The setting procedure
depends on the function you select.
3
4MENU END
Menu Screen
If you select “INDEX” . . .
.... ੬ pg. 56.
•Select the desired still image in the INDEX
Menu Screen, then press the MENU Jog Dial.
The selected still image appears on the whole
screen, then the screen enters normal
playback. It is not necessary to perform steps 4
and 5.
EXIT <PROTECT>
01
02
03
04
05
If you select “SLIDE SHOW 1”, “SLIDE SHOW 2”,
“PROTECT” or “DELETE”. . .
.... see respective pages.
Setting Menu
(ex. PROTECT)
END SETTING
Press the MENU Jog Dial. The Menu Screen
4
5
reappears and the highlight bar is on “MENU END”.
MENU
INDEX
CLOSE MENU
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
Press the MENU Jog Dial. The normal screen
reappears.
DELETE
4
MENU END
Normal Screen
EN
55
Mode
Effect
INDEX
All still images stored in memory can be displayed six at a time. This mode is a
convenient way to look for the still image you want to view and to check the still
images you shot beforehand (੬ pg. 56).
SLIDE SHOW 1
Allows you to run through all the still images stored in memory automatically in
numerical order. Each still image is displayed. This mode is like a regular slide-
show (੬ pg. 60).
The still image wipes in over the last one from the bottom of the screen to the top
SLIDE SHOW 2
PROTECT
(੬ pg. 60).
Lets you protect selected still images from accidental erasure. Select a still image
for which you want to perform “Protect” to put a padlock mark next to it. A still
image with a padlock mark cannot be deleted. When selecting a still image to
protect, you can check six still images stored in memory at a time (੬ pg. 57).
Allows you to delete some still images already stored in memory (੬ pg. 58).
DELETE
CAUTION:
While “ENTER” is selected on the Delete Execute Menu and it is blinking,
switching off the camcorder or removing the power supply unit (battery pack or
AC Power Adapter/Charger) may cause the camcorder’s built-in memory to
become corrupt. Never remove the power supply unit at this stage.
SELECT
Allows you to check 6 still images stored in memory at a time, to
select the still images you want to delete.
ALL
Allows you to delete all the still images at once except protected
images.
D.S.C. PLAYBACK Advanced Features (cont.)
56
EN
Index
You can view all still images stored in memory six at a
time. Use this mode when looking for a still image you
want to view and when checking the still images you
shot beforehand.
ACCESS MENU SCREEN
Press the MENU Jog Dial.
1
Set the System Select
Switch to “D.S.C.”.
MENU Jog Dial
ACCESS INDEX MENU SCREEN
Rotate the MENU Jog Dial to move the highlight bar
to “INDEX”, then press it.
2
3
Viewfinder
MENU
VIEW INDEX IMAGES
Rotate the MENU Jog Dial to move the frame to the
desired still image, then press it. The one you
selected is displayed on the whole screen, then the
screen enters normal playback.
INDEX
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
DELETE
•On the Index Menu Screen, 6 still images are
displayed at a time. When viewing the still images
that follow the 6th one, rotate the MENU Jog Dial
to move the frame from Index No. 1 to No. 6, and
then rotate it further downward. The frame is
placed on the 7th still image automatically. Images
after the 7th one can also be accessed in the same
way.
4
MENU END
Menu Screen
EXIT
01
<INDEX>
02
03
•If the desired still image cannot be found, place
the highlight bar on “EXIT”, then press the MENU
Jog Dial twice to exit the Menu Screen.
04
06
NOTES:
Index Menu Screen
● When moving the frame from the 7th still image back
to the 6th, rotate the MENU Jog Dial upward to place
the highlight bar on “EXIT”, then rotate it further
upward. The frame is moved to the 6th still image.
Perform the same procedure for the 13th image.
● On the Index Menu Screen, a star mark is displayed
next to a still image you shot in the FINE mode.
Playback screen
EN
57
Protect
This mode helps prevent accidental erasure of images.
Put a padlock mark next to the desired still image, and
that still image cannot be deleted.
ACCESS MENU SCREEN
Press the MENU Jog Dial.
1
ACCESS PROTECT MENU SCREEN
Set the System Select
Switch to “D.S.C.”.
MENU Jog Dial
Rotate the MENU Jog Dial to move the highlight bar
2
to “PROTECT”, then press it.
•If you do not want to perform “Protect” for any still
image, go to step 4.
Viewfinder
MENU
INDEX
SET PROTECT
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
Rotate the MENU Jog Dial to move the frame to the
desired still image, then press it. The padlock mark
appears above the selected image.
3
DELETE
•On the Protect Menu Screen, all still images are
displayed six at a time. To perform “Protect” for
the still images that come after the 6th one, rotate
the MENU Jog Dial to move the frame from Index
No. 1 to No. 6, then rotate it further downward.
The frame is placed automatically on the 7th still
image. Images after the 7th one can also be
accessed in the same way.
4
MENU END
Menu Screen
EXIT <PROTECT>
01
03
•To complete “Protect”, go to step 4.
04
05
06
CLOSE MENU
Rotate the MENU Jog Dial upward to place the
highlight bar on “EXIT”, then press it twice.
4
Protect Menu Screen
To remove “Protect”. . .
EXIT <PROTECT>
01
03
Perform steps 1 and 2, rotate the MENU Jog Dial to move
the frame to the desired still image with the padlock
mark, then press it. The padlock mark located above the
still image disappears and the image is no longer
protected. When finished removing protection, perform
step 4.
04
05
06
A padlock mark appears.
NOTES:
● To move the frame from Index No. 7 to 6, place the
highlight bar on “EXIT” by rotating the MENU Jog Dial
upward. Rotate the MENU Jog Dial further upward.
The frame is moved to the 6th still image automatically.
Perform the same procedure for still images that follow
the 13th one.
● On the Protect Menu Screen, a star mark is displayed
next to a still image you shot in the FINE mode.
D.S.C. PLAYBACK Advanced Features (cont.)
58
EN
Delete
When the memory in which still images are stored
becomes full, the number of remaining shots available
reaches “0” (blinking). In this situation it becomes
impossible to take your next shot. Delete some still
images already stored in memory to make room for new
shots.
Set the System
Select Switch to “D.S.C.”.
ACCESS MENU SCREEN
Press the MENU Jog Dial.
MENU Jog Dial
1
2
3
Viewfinder
MENU
ACCESS DELETE MENU SCREEN
Rotate the MENU Jog Dial to move the highlight bar
to “DELETE”, then press it.
INDEX
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
DELETE
SELECT DELETE MODE
Rotate the MENU Jog Dial to move the highlight bar
to “SELECT” or “ALL”, then press it.
4
MENU END
To select a still image by checking the still images
stored in memory . . .
.... select “SELECT”, then go to step 4.
To delete all the still images stored in memory at
once without checking them . . .
.... select “ALL”, then go to step 5.
Menu Screen
DELETE
SELECT
ALL
To quit the Delete Mode . . .
.... rotate the MENU Jog Dial to place the highlight
bar on “EXIT”, then press it twice.
In case of
“ALL”
EXIT
SELECT ON DELETE SELECT MENU
SCREEN
Delete Menu Screen
In case of
“SELECT”
Rotate the MENU Jog Dial to move the frame to the
desired still image, then press it. “ ” appears above
the selected still image. When you have finished
selecting all the desired still images, rotate the
MENU Jog Dial upward to place the highlight bar on
“NEXT”, then press the MENU Jog Dial.
4
NEXT <DELETE>
01
02
04
05
06
•On the Delete Select Menu Screen, the still images
are displayed six at a time. To delete the still
images that follow the 6th one, rotate the MENU
Jog Dial to move the frame from No. 1 to No. 6,
then rotate it further downward. The frame is
moved to the 7th still image automatically.
Perform the same procedure for still images that
follow the 7th one.
Delete Select Menu Screen
DELETE
CANCEL
ENTER
Delete Execute Menu Screen
Menu Screen
EN
59
In case of “SELECT”
ACCESS DELETE EXECUTE MENU
SCREEN
NEXT <DELETE>
Rotate the MENU Jog Dial to move the highlight bar
to “CANCEL” or “ENTER”, then press it.
01
02
06
5
6
•“CANCEL” does not delete the selected still images
and the screen returns to the Menu Screen.
•“ENTER” deletes the selected still images. While
“ENTER” blinks, they are in the process of being
deleted from memory. After deleting is finished,
the screen returns to the Menu Screen.
04
05
CLOSE MENU
Press the MENU Jog Dial again to exit the Menu
Screen.
If you check the remaining still images on
Index Menu Screen after deleting...
CAUTION:
While “ENTER” is selected on the Delete Execute
Menu and it is blinking, switching off the camcorder
or removing the power supply unit (battery pack or
AC Power Adapter/Charger) may cause the
camcorder’s built-in memory to become corrupt.
Never remove the power supply unit at this stage.
EXIT
01
<INDEX>
02
03
06
04
05
NOTES:
● Before deleting some still images stored in memory,
perform “Protect” for the necessary ones (੬ pg. 57) or
save them on a PC so that you do not lose them
accidentally (੬ pg. 61).
● Even if “ALL” is selected on the Delete Menu Screen, it
is not possible to delete a still image with a padlock
mark. “ALL” only deletes all still images that are not
protected. After images are deleted from memory, the
remaining images are automatically moved up to fill in
any gaps in the numerical sequence. The Index No. for
images protected (with the padlock mark) may
therefore change.
● When selecting the desired still image in step 4, to
move the frame from No. 7 to 6, place the highlight bar
on “EXIT” by rotating the MENU Jog Dial upward.
Rotate it further upward to move the frame to No. 6.
Perform the same procedure for still images that follow
the 13th one.
● On the Delete Select Menu Screen, a star mark is
displayed next to a still image you shot in the FINE
mode.
D.S.C. PLAYBACK Advanced Features (cont.)
60
EN
Slide Show
You can run through all the still images stored in memory
automatically. This is like a regular slide-show. There are
2 types available. Select either according to your needs.
ACCESS MENU SCREEN
Press the MENU Jog Dial.
1
Set the System Select
Switch to “D.S.C.”.
ACCESS SLIDE SHOW
MENU Jog Dial
Rotate the MENU Jog Dial to move the highlight bar
to “SLIDE SHOW 1” or “SLIDE SHOW 2”, then
press it.
2
3
Viewfinder
If you select “SLIDE SHOW 1” . . .
.... all still images stored in memory are displayed
in numerical order.
MENU
Menu Screen
INDEX
SLIDE SHOW 1
SLIDE SHOW 2
PROTECT
If you select “SLIDE SHOW 2”. . .
.... the still image wipes in to push up the previous
one from the bottom of the screen to the top.
DELETE
•To end “SLIDE SHOW”, press the MENU Jog Dial.
The still image which follows the still image
displayed at the moment the MENU Jog Dial is
pressed appears, then the screen returns to the
Menu Screen.
4MENU END
Ex. SLIDE SHOW 1
Ex. SLIDE SHOW 2
CLOSE MENU
Press the MENU Jog Dial.
D.S.C. PLAYBACK Connection
EN
61
Connection to a Windows® PC/Macintosh®
Image data stored in the camcorder's built-in memory
can be transferred to a Windows® PC or Macintosh® and
saved using the provided image transfer software. The
image data transferred to a personal computer can also
be further processed using Paint Software, and the still
image processed on the PC can be inserted onto a tape
(੬ pg. 69).
Set to “D.S.C.”
To DIGITAL jack
(8-pin)
CONNECT TO PERSONAL
COMPUTER
Connect the camcorder’s DIGITAL jack to the COM
1
2
Port (RS-232C) on a Windows PC or to the Modem
Port/Printer Port (8-pin) on a Macintosh, using the
provided PC connection cable.
PC connection
cables (provided)
SELECT MODE
Set the System Select Switch to “D.S.C.”, then set
the Power Switch to “PLAY”.
For Macintosh®:
To Modem Port
or Printer Port
For Windows®:
To COM Port
(RS-232C)
•A still image stored in memory appears.
•When transferring still images to a computer, be
sure that a still image is displayed on the screen.
RUN IMAGE TRANSFER SOFT-
WARE
Launch the provided software on your Windows®
PC or Macintosh®. Transfer the still images stored in
the camcorder’s memory to the Windows® PC or
Macintosh®. Refer to the software’s instruction
manual on the provided CD-ROM for details.
3
4
•During transfer of the still image, the camcorder’s
screen becomes blue and “
” is dis-
PC MODE
played. After transferring is finished, the screen
displays the same still image as in step 2.
Viewfinder
END TRANSFERRING
Close the software, then switch off the camcorder.
PC MODE
NOTES:
● Before transferring still images from your personal computer to the camcorder’s built-in memory, perform
the camcorder’s Picture Mode Setting (੬ pg. 47). The still images will be transferred from the personal
computer in the selected Picture Mode.
● When transferring still images from your personal computer to the camcorder, make sure the number of
images to be transferred is smaller than the camcorder's remaining number of shots available.
● Use the AC Power Adapter/Charger as the power supply instead of the battery pack.
● The still images stored in the camcorder’s memory are not automatically removed after being transferred to
the PC. If you wish to remove those still images from the camcorder's memory, delete them (੬ pg. 58, 59).
● Windows® are trademarks of Microsoft Corporation, registered in the U.S.A. and other countries.
● Macintosh® are trademarks of Apple Computer Inc., registered in the U.S.A. and other countries.
USING REMOTE CONTROL UNIT
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic
operations (PLAY, STOP, PAUSE, FF, and REW) of your VCR. This remote control unit makes additional
recording functions possible.
62
EN
INSTALLING THE BATTERY
A
B
C
1
PULL OUT BATTERY
2
2
3
a
2
3
1
3
HOLDER
1
Release
tab
A
Type
Type
Type
: Pull out by inserting a pointed
1
Lock hole
1
a
1
instrument into slot
.
B
C
: Pull out while sliding the lock
hole.
: Pinch the release tab and pull
out.
1
2
#
1
7
%
2
7
8
9
0
!
@
INSERT BATTERY
$
8
9
3
4
5
6
Making sure the plus (+) side is up, insert
the lithium battery (CR2025)* into the
battery holder.
2
3
!
5
0
3
^
@
4
6
REPLACE BATTERY HOLDER
Insert the battery holder into the remote
control unit, and push the holder until it
clicks into place.
&
* Read the caution concerning lithium
batteries (੬ pg. 2).
RM-V705U
(provided)
RM-V700U
(optional)
FUNCTIONS
BUTTONS
With the camcorder’s power switch
set to “CAMERA”.
With the camcorder’s power switch
set to “PLAY”.
1 Infrared beam
Transmits the beam signal.
transmitting window
2 ZOOM (T/W) Buttons Zoom in/out (੬ pg. 20)
—
Playback start (੬ pg. 40)
Stop (੬ pg. 40)
3 PLAY Button
—
—
4 STOP Button
5 REW Button
Retake (rewind)/Quick Review (੬ pg. 21) Rew/Rew Shuttle Search (੬ pg. 40, 42)
Insert Editing (੬ pg. 68, 69)
Functions same as the Recording Start/Stop button on the camcorder.
6 INSERT Button
7 START/STOP Button
8 INT. TIME Button
9 REC TIME Button
0 PAUSE Button
! FF Button
—
Self-Timer/Time-Lapse (੬ pg. 63)
—
—
Animation/Time-Lapse (੬ pg. 63)
—
Pause (੬ pg. 42)
Retake (forward) (੬ pg. 21)
FF/FF Shuttle Search (੬ pg. 40, 42)
@ A.DUB Button
# PAUSE IN Connector
$ MBR SET Button
% VISS Button
—
Audio dubbing (੬ pg. 70)
੬ pg. 65
—
—
੬ pg. 64
Index Code marking (੬ pg. 63)
—
^ VCR CTL Button
& R.A.EDIT Buttons
—
—
੬ pg. 64
੬ pg. 66
# — & : RM-V700U only.
EN
63
FEATURE:
PURPOSE:
Self-Timer, Animation and Time-Lapse
The remote control lets you set/release
Interval Timer and Rec Time functions
as well as the Menu Screen.
Transmitted beam
effective area
OPERATION:
Self-Timer
1) Set
15°
Instead of performing steps 1 through
4 on pg. 38 (“Self-Timer”), press INT.
TIME on the remote control. Each
time INT. TIME is pressed, the
Interval Timer indicator appears,
changing in the following order: 15S,
30S, 1MIN, 5MIN and No indication
(off).
Remote sensor
15°
When using the remote control, be sure to
point it at the remote sensor. The above
illustration shows the approximate transmitted
beam effective area for indoor use.
The transmitted beam may not be effective or
may cause incorrect operation outdoors or
when the remote sensor is directly exposed to
sunlight or powerful lighting.
2) Release
Instead of setting “INT. TIME” to
“OFF” in the Menu, press INT. TIME
on the remote control until the
Interval Timer indicator disappears.
Animation
1) Set
Instead of performing steps 1 and 2
on pg. 39 (“Animation”), press REC
TIME on the remote control. Each
time REC TIME is pressed, the Rec
Time indicator appears, changing in
the following order: 1/4S, 1/2S, 1S,
5S and No indication (off).
Interval Timer Indicator
Viewfinder
1MIN
1 2S
INDEX
Index Code
Marking
2) Release
Instead of using the Menu in step 5
on pg. 39, press REC TIME on the
remote control until the Rec Time
indicator disappears.
Rec Time Indicator
Time-Lapse
1) Set
Instead of performing steps 1 through
3 on pg. 39 (“Time-Lapse”), press
INT. TIME and REC TIME on the
remote control. Each time INT. TIME
is pressed, the Interval Timer
indicator appears, changing in the
following order: 15S, 30S, 1MIN,
5MIN and No indication (off). Each
time REC TIME is pressed, the Rec
Time indicator appears, changing in
the following order: 1/4S, 1/2S, 1S,
5S and No indication (off).
2) Release
Instead of using the Menu in step 5
on pg. 39, press INT. TIME and REC
TIME on the remote control until the
indicators disappear.
START/STOP
VISS
NOTE:
Also refer to pgs. 38 and 39.
INT. TIME
REC TIME
FEATURE:
PURPOSE:
Index Code Marking (RM-V700U only)
To give you automatic access to any
selected point on a recording.
OPERATION:
NOTE:
1) Press VISS once to place the index
code. “INDEX” blinks during
marking.
If VISS is pressed during Record-
Standby mode, the mark is placed
where START/STOP is pressed.
RM-V700U
(optional)
RM-V705U
(provided)
OR
USING REMOTE CONTROL UNIT (cont.)
64
EN
Random Assemble Editing [R.A.Edit]
Create edited videos easily using your camcorder as the
source player. You can select up to 8 “cuts” for automatic
editing, in any order you like. R.A.Edit is more easily
performed when the optional RM-V700U MBR (Multi-
Brand Remote, ੬ pg. 62) is set to operate with your
brand of VCR (see VCR CODE LIST), but can also be
performed by operating the VCR manually.
MBR SET
VCR CTL
1
4
7
2
5
8
3
6
9
Before operation, make sure the lithium battery is
installed in the remote control RM-V700U (੬ pg. 62).
0
RM-V700U
(optional)
SET REMOTE/VCR CODE
VCR CODE LIST
SET REMOTE TO OPERATE VCR
Turn off the power to the VCR and point the remote
toward the VCR’s infrared sensor. Then, referring to
the VCR CODE LIST on the left, press and hold MBR
SET, and press button (A) and then (B).
VCR BRAND BUTTONS
VCR BRAND BUTTONS
NAME
(A) (B)
NAME
(A) (B)
1
2
GE
1
9
9
9
1ꢀ
2ꢀ
`ꢀ
4
PHILIPS
3
7
3ꢀ
2
PANASONIC
1
1
1
9
1
3ꢀ
7ꢀ
1ꢀ
4ꢀ
8ꢀ
•The code is automatically set once you release the
MBR SET button, and the VCR’s power comes on.
HITACHI
6
6
6ꢀ
3
OPERATE VCR
JVC
A
B
C
9
9
9
1ꢀ
6ꢀ
3
Make sure the VCR’s power is on. Then, while
holding VCR CTL, press the button on the remote for
the desired function. The functions the remote can
control are PLAY, STOP, PAUSE, FF, REW and VCR
REC STBY (you don’t need to press VCR CTL for this
one).
ꢀ
RCA
9
9
6
6
9
2ꢀ
4ꢀ
6ꢀ
3ꢀ
`
MAGNAVOX
9
1
7
7
5ꢀ
1ꢀ
1ꢀ
6
SANYO
SHARP
SONY
3
3
6ꢀ
5
You’re now ready to try Random Assemble Editing.
MITSUBISHI
NEC
6
6
7ꢀ
8
1
1
5ꢀ
`
IMPORTANT
3
3
7ꢀ
8
Although the MBR is compatible with JVC VCRs and
those of many other makers, it may not work with yours
or may offer limited functions.
6
6
3
3
5ꢀ
`ꢀ
9ꢀ
1ꢀ
PHILIPS
1
9
1
9
9
9
1
9ꢀ
5ꢀ
1ꢀ
4ꢀ
1ꢀ
6ꢀ
2
NOTES:
ꢀ
● If the VCR’s power doesn’t come on in step 1, try
another code from the VCR CODE LIST.
● Some brands of VCR don’t come on automatically. In
this case, turn the power on manually and try step 2.
● If the RM-V700U is not able to control the VCR, use
the controls on the VCR.
TOSHIBA
ZENITH
6
6
9ꢀ
1
1
6
EN
65
MAKE CONNECTIONS
CONNECT TO . . .
A
JVC VCR EQUIPPED WITH REMOTE
PAUSE TERMINAL
Connect the editing cable to the Remote PAUSE
terminal.
1
Open the cover
B
C
JVC VCR NOT EQUIPPED WITH REMOTE
PAUSE TERMINAL BUT EQUIPPED WITH
R.A. EDIT CONNECTOR
To AUDIO and
VIDEO OUT
connectors
To J terminal
(JLIP)
Connect the editing cable to the R.A.EDIT
connector.
B
A
VCR OTHER THAN TYPE OR
Connect the editing cable to the RM-V700U’s
Pause-In jack.
Audio and
Video cables
(optional)
Editing cable
(optional, ø3.5
mini-plug cable)
PREPARE CAMCORDER
Insert a recorded tape. Set the System Select Switch
to “VIDEO”, and set the Power Switch to “PLAY”.
2
3
PREPARE VCR
C
A B
Turn the power on, insert a recordable tape and
engage the AUX mode (refer to VCR’s instructions).
To AUDIO
and VIDEO IN
connectors
To Pause-In
To Remote
PAUSE
VCR
(Recording deck)
RM-V700U
(optional)
USING REMOTE CONTROL UNIT (cont.)
SELECT SCENES
66
EN
PLAY/PAUSE
FF
ACCESS R.A. EDIT COUNTER
DISPLAY
STOP
Press PLAY/PAUSE, then press ON/OFF and the
1
2
3
counter display appears in the viewfinder, and the
screen of the connected TV.
REW
REGISTER BEGINNING OF SCENE
Press REW or FF to locate the beginning of a scene
you want, then press IN/OUT to register that point.
The data appears under “IN” on the display.
REGISTER END OF SCENE
Press REW or FF to locate the end of the scene and
press IN/OUT to register it. The data appears under
“OUT” on the display. The total time of the
registered scene(s) is displayed at the bottom of the
screen.
REGISTER ADDITIONAL SCENES
Repeat steps 2 and 3 for each additional scene
(as many as 8).
4
5
RM-V700U
(optional)
MAKE CORRECTIONS
Press CANCEL during steps 2 and 3 to erase the
FF
PAUSE
most recently registered point.
REW
PLAY
IN/OUT
ON/OFF
CANCEL
NOTES:
● There must be at least one second between an in-point
and its corresponding out-point.
● To ensure correct operation, there should be at least 15
seconds between an out-point and the next in-point.
● Blank portions of tape cannot be registered as in-points
or out-points.
● If it takes more than 5 minutes to search for an in-point,
the VCR’s Record-Pause mode is cancelled and editing
doesn’t take place.
● Pressing ON/OFF clears all in- and out-points from
memory.
● Leave a small margin for error around each in-point to
ensure the scene is recorded in its entirety.
IN
0:00:25
OUT
--:--:--
1
2
3
4
5
6
7
8
COUNTER
TOTAL
0:00:25
0:00:00
IN
OUT
1
2
3
4
5
6
7
8
0:00:25
0:01:05
0:03:18
0:02:33
0:04:11
0:03:31
0:02:53
--:--:--
COUNTER
TOTAL
0:04:11
0:01:13
EN
67
AUTOMATIC EDITING TO VCR
Original tape (camcorder)
1
IN
3
2
IN
ENGAGE VCR’S RECORD-PAUSE
MODE
OUT
IN OUT
OUT
Point the remote control toward the VCR’s infrared
sensor and press VCR REC STBY, or manually
engage the VCR’s Record-Pause mode.
1
2
Edited tape (VCR)
BEGIN AUTOMATIC EDITING
Press the MENU Jog Dial on the camcorder, and the
previously selected scenes are copied to the VCR in
the specified order.
While editing, the R.A. Edit counter of the scene
which is beging copied is shown with a blinking
highlight.
STOP
END AUTOMATIC EDITING
When all selected scenes have been copied, the
camcorder and VCR enter the still or pause mode.
Press STOP on both units. To make the R.A. Edit
counter display disappear, press ON/OFF.
3
•When finished editing, be sure to disconnect the
editing cable and the audio/video cable.
NOTES:
C
● If you performed step 1
on page 65 (“MAKE
CONNECTIONS”), keep the remote control pointed at
the VCR during editing.
MENU Jog Dial
● The on-screen display only appears while the
camcorder searches for each scene.
● There may be noise at in- or out-points on the edited
tape with certain VCRs.
RM-V700U
(optional)
ON/OFF
VCR REC STBY
USING REMOTE CONTROL UNIT (cont.)
68
EN
Insert Editing (VIDEO)
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in- and out-points. The
original audio remains unchanged.
COUNTER R/M
PLAY/PAUSE
NOTE:
REW
FF
Use the RM-V705U or RM-V700U remote control unit to
perform this procedure.
SELECT MODE
STOP
Set the System Select Switch to “VIDEO”, then set
1
2
the Power Switch to “PLAY”.
FIND EDIT-OUT POINT
Play back the tape, locate the Edit-out point and
press PAUSE on the camcorder or the remote
control.
RESET COUNTER
Power Switch
Press and hold COUNTER R/M for more than
1 second to reset the tape counter, then press again
for less than 1 second and make sure “M” appears.
3
4
Viewfinder
Insert editing
indicator
FIND EDIT-IN POINT
Press REW to go a little beyond the beginning of the
scene you want to replace, press PLAY to view the
recorded tape, and press PAUSE exactly at the
point where the new scene should start.
M–0:12:34
Tape Counter
ENGAGE INSERT EDITING MODE
Press and hold INSERT, and without releasing
INSERT, press and release PAUSE. The Insert
mode is engaged. When the scene the camcorder is
aimed at appears on the screen, go to the next step.
System Select Switch
5
BEGIN INSERT EDITING
Press START/STOP. When the counter reaches
“0:00:00”, editing stops automatically and the
camcorder enters the Insert-Pause mode.
6
7
END INSERT EDITING
Press STOP.
START/STOP
REW
NOTES:
● After step 5, Retake (੬ pg. 21) can be performed.
● The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
● Only video signal is recorded in the Insert Editing
mode.
PLAY
PAUSE
REW
INSERT
RM-V700U
(optional)
RM-V705U
(provided)
OR
EN
69
Insert Editing (Insert A Still Image From
The Built-in Memory Onto A Tape)
COUNTER R/M
You can insert a still image stored in the camcorder's
built-in memory into a previously recorded tape,
replacing a section of the original recording with minimal
picture distortion at the in- and out-points. The original
audio remains unchanged.
PLAY/PAUSE
REW
FF
Perform steps 1 through 5 in Insert Editing (VIDEO)
(੬ pg. 68) before the following procedure.
STOP
NOTE:
Page Button
Use the RM-V705U or RM-V700U remote control unit to
perform this procedure.
SELECT STILL IMAGE
First set the System Select Switch to “D.S.C.”. Press
the Page Button to select the still image you wish to
insert.
1
2
BEGIN INSERT EDITING
Power Switch
Press START/STOP. When the counter reaches
“0:00:00”, editing stops automatically and the
camcorder enters the Insert-Pause mode.
Viewfinder
Insert editing
indicator
To insert still images in sequential order onto the
tape . . .
.... press the Page Button to move the page forward.
To insert still images at random onto the tape . . .
.... first record the still image you selected in step 1
onto the tape, then press START/STOP to
M–0:12:34
Tape Counter
engage the Insert-Pause mode. To select another
still image, press the Page Button again, then
press START/STOP. Insert-Editing begins.
System Select Switch
END INSERT EDITING
Press STOP.
3
NOTES:
● The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
● Only video signal is recorded in the Insert Editing
mode.
START/STOP
REW
PLAY
PAUSE
REW
INSERT
RM-V700U
(optional)
RM-V705U
(provided)
OR
USING REMOTE CONTROL UNIT (cont.)
70
EN
Viewfinder
Audio Dubbing
e
4
Audio dubbing
indicator
You can record a new soundtrack on a prerecorded tape
(normal audio only).
M–0:05:20
Perform steps 1, 2 and 3 of the Insert Editing (VIDEO)
procedure (੬ pg. 68) before continuing.
•The sound comes from the built-in microphone (or an
external microphone if connected).
FIND EDIT-IN POINT
Press REW to go a little beyond the beginning of the
1
scene onto which you want to dub new audio, press
PLAY to view the recorded tape, then press PAUSE
at exactly the point where dubbing should start.
Set to “VIDEO”
ENGAGE AUDIO DUB-STANDBY
MODE
Press and hold A. DUB, and without releasing
2
3
A. DUB, press and release PAUSE.
BEGIN AUDIO DUBBING
Press PLAY. When the counter reaches “0:00:00”,
Audio Dubbing stops automatically and the
camcorder enters the Audio Dub-Standby mode.
To external
microphone input
jack (capped)
Microphone
END AUDIO DUBBING
Press STOP.
4
REW
NOTES:
● Do not press FF or REW during Audio Dub-Standby, or
the edit points will not be accurate.
PLAY
PAUSE
● If the microphone is too close to the TV, or if the TV’s
volume is too high, whistling or howling may occur.
REW
A. DUB
NOTES (for Insert Editing and
RM-V700U
(optional)
RM-V705U
(provided)
Audio Dubbing):
OR
● Insert Editing and audio Dubbing may not work
correctly if the tape contains blank segments, or if the
recording speed was changed during the original
recording.
● To edit/dub onto a tape, make sure the Erase Protection
tab is in the position that allows recording. If not, slide
the tab. Some cassettes have removable tabs. If the tab
has been removed, cover the hole with adhesive tape.
● Do not press STOP during Insert Editing or Audio
Dubbing, or the edit points will not be accurate.
● During Insert Editing and Audio Dubbing, when Insert-
Pause or Audio Dub-Standby is engaged, the counter
may go slightly past “0:00:00”. Recording, however,
stops at exactly 0:00:00.
USER MAINTENANCE
EN
71
LENS COVER
Open/Close Switch
After Use
Set the Power Switch to “POWER OFF” to turn off
the camcorder.
1
2
3
4
5
Slide EJECT to open the cassette holder, then remove
the cassette.
Close and lock the cassette holder by pressing
PUSH.
Slide BATT. RELEASE to remove the battery pack.
Slide the LENS COVER Open/Close switch to close
Set to “POWER OFF”.
BATT. RELEASE
the lens cover.
Cleaning The Camcorder
EJECT
CLEAN EXTERIOR
Wipe gently with a soft cloth.
1
CLEAN LENS
Blow it with a blower brush, then wipe gently with
2
3
lens cleaning paper.
PUSH
CLEAN VIEWFINDER
Remove.
1 Turn the eyepiece counterclockwise and pull
it out.
2 Remove dust using a blower brush.
3 Align the marks, re-attach the eyepiece and turn
it clockwise.
NOTES:
● Avoid using strong cleaning agents such as benzine or
alcohol.
● Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.
Marks
● Mould may form if the lens is left dirty.
INDEX
72
EN
1 2 3
4
5 6
7
8
30MIN
4
S.LX
T30
9
&
REC SP
FINE 12
*
)
444
TWILIGHT
0
(
q
w
NORM 01
!
#
$
LENS COVER MWB
@
PAUSE
P
5MIN
1 4S TAPE END
e
%
MERRY CHRISTMAS
DEC 25.98 AM 11:45:18
^
EN
73
Viewfinder Indications
1 Cassette Warning/
$ •Record–Standby Mode
Tape Remaining Time ................ ੬ pg. 19
Indicator ................................. ੬ pg. 18
When no cassette is inserted: the cassette
•Lens Cover Warning:
(
) warning blinks.
LENS COVER .......................... ੬ pg. 19
•Data Transfer Display:
When Erase Protection tab is not in the
position that allows recording: the cassette
MODE. ................................ ੬ pg. 61
PC
(
) warning lights. Otherwise, the tape
% Instant Title Display ................... ੬ pg. 30
^ Date/Time Display ..................... ੬ pg. 22
& Battery Pack Remaining Power Indicator
Changes as follows according to the battery
pack’s remaining power level:
remaining time is displayed and the tape
remaining time warning blinks when the
tape is about to reach its end.
When the Power Switch is set to “PLAY”
and a tape is loaded: the cassette ( ) mark
is displayed regardless of the Erase
Protection tab’s position.
“
”. When the power is
almost gone, the indicator “ ” blinks
(battery power warning), then the unit
shuts off. Replace the battery pack with a
fully charged one.
2 Recording Mode (SP/EP)
Indicator.................................... ੬ pg. 16
3, 0 Program AE Indicator ............ ੬ pg. 26
Note: The symbol containing 3 darkened
Displayed at 3 for approx. 1 second when
the Select Dial is switched from one
position to another. Then only the indica-
tor remains at 0.
squares —
— does not necessarily
mean that the battery pack is fully
charged.
* Focus Indicator.......................... ੬ pg. 35
3, ! Fade/Wipe-Standby
( Exposure Control Level
Indicator.................................... ੬ pg. 28
Displayed at 3 for approx. 2 seconds
when the Fade/Wipe is switched from one
function to another by pressing the EFFECT
button. Then only the indicator remains at
!.
Counter ..................................... ੬ pg. 36
) White Balance Mode
Indicator.................................... ੬ pg. 37
q Snapshot Mode Display....... ੬ pg. 25, 46
w Clock Battery Warning
4 Multi-Function Control
Blinks for approx. 10 seconds when the
power is turned on. This display also
blinks when the clock (lithium) battery is
either not installed or has discharged.
Install or replace the old battery with a
new one (੬ pg. 12).
Indication............................ ੬ pg. 28, 29
Displayed when any of the buttons located
on the Multi-Function Control is pressed.
The indication disappears within approx. 2
seconds.
5 Picture Mode Display.......... ੬ pg. 25, 46
Remaining Number Of
e •Tape End Display:
TAPE END ............................... ੬ pg. 19
Shots Indicator ................... ੬ pg. 25, 46
Appears when the end of the tape is
reached during playback, recording or
fast-forward.
6 Super LoLux Indicator ............... ੬ pg. 29
7 Tape Length Indicator ................ ੬ pg. 16
8 Zoom Indicator Bar ................... ੬ pg. 20
9 Recording Indicator................... ੬ pg. 18
@ Picture Stabilizer Indicator ........ ੬ pg. 21
•Condensation Warning:
When this indication appears, all func-
tions except tape eject and power on/off
are disabled. Turn the unit off (without
removing the power source) for a few
hours, and when you turn it on again the
indication should disappear.
# Interval Timer/Recording Time
Indicator.................................... ੬ pg. 38
INDEX (cont.)
74
EN
W
1
5
6
7
9
0
!
4
8
r E R
2
3
p
T
^
A
B
U
&
Y
FINE
STD
e
@ # $
%
I
*
(
)
a
O
t
y
u
i
o
P
q w Q
EN
75
Controls
Connectors
1 Power Zoom Button ........................... ੬ pg. 20
e DC IN Jack ......................................... ੬ pg. 11
Page Button........................................ ੬ pg. 53
The jacks r to o are located beneath the jack
cover.
2 Select Dial ......................................... ੬ pg. 26
3 Multi-Function Control
r External Microphone Input Jack ......... ੬ pg. 70
•EFFECT Button ................................. ੬ pg. 28
•WIDE Button ................................... ੬ pg. 29
•TITLE Button .................................... ੬ pg. 30
•SUPER LOLUX Button ..................... ੬ pg. 29
4 PUSH Button...................................... ੬ pg. 17
t J terminal
[ JLIP (Joint Level Interface Protocol) Connector ]
•Connect the editing cable when performing
Random Assemble Editing (੬ pg. 64 – 67).
•It is used to connect the camcorder to a device
such as a personal computer.
For further detail consult your nearest JVC
dealer.
•JLIP-controlled editing from camcorder to VCR
is not possible if the VCR is not equipped with
a J terminal.
5 Recording Mode [SP/EP] Button ......... ੬ pg. 16
6 DATE/TIME Button ............................. ੬ pg. 22
COUNTER R/M Button ....................... ੬ pg. 42
7 P. [Picture] STABILIZER Button ........... ੬ pg. 21
8 REW Button ....................................... ੬ pg. 40
RETAKE R [Quick Review] Button ...... ੬ pg. 21
9 PLAY/PAUSE Button ........................... ੬ pg. 40
y Digital Jack ........................................ ੬ pg. 61
u AUDIO OUT Connector .................... ੬ pg. 44
i VIDEO OUT Connector ..................... ੬ pg. 44
o RF DC OUT Connector ...................... ੬ pg. 44
0 FF Button ........................................... ੬ pg. 40
RETAKE F Button ................................ ੬ pg. 21
! STOP Button ...................................... ੬ pg. 40
@ EJECT Switch ...................................... ੬ pg. 17
Indicators
p Tally Lamp ......................................... ੬ pg. 18
Q Power Indicator .................................. ੬ pg. 18
# Function Navigator Dial
[MENU Jog Dial] ................................ ੬ pg. 13
$ LIGHT OFF/AUTO/ON Switch ........... ੬ pg. 23
% BATT. [Battery] RELEASE Switch ......... ੬ pg. 10
^ Dioptre Adjustment ............................ ੬ pg. 14
Other Parts
W Video Light......................................... ੬ pg. 23
E Microphone ....................................... ੬ pg. 70
& System Select
R •Camera sensor
[VIDEO/D.S.C.] Switch .... ੬ pg. 18, 40, 46, 53
Be careful not to cover this area; built-in
here is the sensor necessary for shooting.
•Remote Sensor ................................. ੬ pg. 63
* MODE Button .............................. ੬ pg. 24, 46
( SNAPSHOT Button ...................... ੬ pg. 24, 46
) LENS COVER Switch .......................... ੬ pg. 18
q Recording Start/Stop Button................ ੬ pg. 18
w Power Switch ................... ੬ pg. 18, 40, 46, 53
T Clock Battery Compartment ............... ੬ pg. 12
Y Battery Pack Mount ............................ ੬ pg. 10
U LCD window
A
Picture Mode Display
B
Remaining Number of Shots Indicator
I Electronic Viewfinder ......................... ੬ pg. 14
O Shoulder Strap Eyelets ........................ ੬ pg. 15
P Grip Strap .......................................... ੬ pg. 14
a Tripod Mounting Socket ..................... ੬ pg. 15
INDEX Terms
76
EN
A
E
AC Power Adapter ................... pg. 10
Animation Recording ............... pg. 39, 63
Audio Dubbing ........................ pg. 70
Auto Date Record .................... pg. 22
Auto Focus............................... pg. 34
Auto Mode Lock Mode ............ pg. 27, 48
Auto Mode Release Mode ........ pg. 27, 48
Electronic Fog Filter Mode ....... pg. 27, 48
Erase Protection ....................... pg. 17
Exposure Control...................... pg. 36
F
Fade-In/Out.............................. pg. 28
Fast-Forward Tape .................... pg. 40
FINE Mode............................... pg. 47
Full Image ................................ pg. 24, 46
B
Battery Pack ............................. pg. 10, 81
Brighten The Image .................. pg. 36
G
Grip Adjustment....................... pg. 14
C
H
Car Battery ............................... pg. 11
Cassette Adapter ...................... pg. 43
Charge Marker ......................... pg. 11
Charging the Battery Pack ........ pg. 10
Clock (Lithium) Battery............. pg. 12
Color Bar ................................. pg. 33, 52
High Speed Shutter Mode ........ pg. 27, 49
I
Index Code Marking................. pg. 63
Index Menu Screen .................. pg. 56
Index Mode.............................. pg. 56
Index Number.......................... pg. 56
Insert Cassette .......................... pg. 17
Insert Editing ............................ pg. 68, 69
Instant Titles ............................. pg. 30
COM Port (RS-232C)................ pg. 61
Connection To A VCR/TV ........ pg. 44
Connection To A Windows
PC/Macintosh ........................ pg. 61
Contents................................... pg. 8, 9
Counter Memory...................... pg. 42
J
JLIP ID NO. .............................. pg. 33, 52
JPEG......................................... pg. 51
D
Darken The Image.................... pg. 36
Date/Time Insert ....................... pg. 22
Date/Time Setting ..................... pg. 13
Delete Menu Screen................. pg. 58
Delete Mode ............................ pg. 58
Delete Select Menu Screen ...... pg. 58
DEMO Mode ........................... pg. 33, 52
Digital Zoom............................ pg. 20, 33, 52
Digital Still Camera .................. pg. 46
Diopter Adjust.......................... pg. 14
Discharge The Battery Pack...... pg. 10
L
Viewfinder Indications ............. pg. 72, 73
M
Manual Focus .......................... pg. 35
MBR Code Setting .................... pg. 64
Modem Port ............................. pg. 61
Move The Page Back................ pg. 53
Move The Page Next................ pg. 53
EN
77
N
S
ND Effect Mode ....................... pg. 27, 48
Self-Timer................................. pg. 38, 49, 63
Sepia Mode.............................. pg. 27, 48
Shooting, Advanced Features
(D.S.C.) .................................. pg. 48 – 52
Nega/Posi Mode....................... pg. 27, 49
P
Shooting (D.S.C.)...................... pg. 46, 47
Shoulder Strap Attachment ....... pg. 15
Shuttle Search .......................... pg. 42
Slide Show Mode ..................... pg. 60
Snapshot Mode ........................ pg. 24, 46
Snapshot (VIDEO) .................... pg. 24
Specifications........................... pg. 84
Sports Mode............................. pg. 27, 49
STANDARD Mode ................... pg. 47
Padlock Mark........................... pg. 57
Picture Mode Setting ................ pg. 47
Picture Stabilizer ...................... pg. 21, 48
Pin-Up Image........................... pg. 24, 46
Playback (D.S.C.) ..................... pg. 53
Playback (VIDEO) .................... pg. 40
Printer Port............................... pg. 61
Program AE With
Special Effects........................ pg. 26, 27
Star Mark On The Setting
Protect Menu Screen ................ pg. 57
Protect Mode ........................... pg. 57
Provided Accessories ............... pg. 9
Menus ................................... pg. 56
Still Image Data Transfer........... pg. 61
Still Playback ........................... pg. 42
Store A Still Image In The
Built-In Memory .................... pg. 46
Super LoLux ............................. pg. 29, 49
Q
Quick Review .......................... pg. 21
R
T
Random Assemble Editing........ pg. 64 – 67
Recording, Advanced
Features (VIDEO) ................... pg. 26 – 39
Tape Counter ........................... pg. 40
Tape Dubbing .......................... pg. 45
Tape Length Setting .................. pg. 16
Time-Lapse Shooting ................ pg. 39, 63
Tracking ................................... pg. 41
Tripod Mounting ...................... pg. 15
Twilight Mode .......................... pg. 27, 49
Recording (VIDEO) .................. pg. 18
Recording, Start/Stop (VIDEO) ... pg. 18, 19
Recording Mode Setting ........... pg. 16
Record-Standby........................ pg. 18
Remote Control Unit ................ pg. 62
Remove Cassette ...................... pg. 17
Retake...................................... pg. 21
Rewind Tape ............................ pg. 40
V
Video Light............................... pg. 23
Viewfinder Adjustment ............. pg. 14
W
White Balance Adjustment ....... pg. 37
Wide Mode .............................. pg. 29, 49
Wipe-In/Out............................. pg. 28
Z
Zooming .................................. pg. 20
TROUBLESHOOTING
78
EN
SYMPTOM
POSSIBLE CAUSE(S)
POWER
No power is supplied.
● The battery pack has not been attached correctly
(੬ pg. 10).
● The battery pack is not charged (੬ pg. 10).
● The power supply has not been correctly connected
(੬ pg. 11).
The power suddenly goes off and
doesn’t come back on by itself.
● The battery pack has completely discharged.
● Remove the cassette and disconnect the power source,
then after a few minutes, try turning the power back on. If
it still doesn’t come on, consult your nearest JVC dealer.
OTHER
Some functions are not available.
● The Select Dial is set to “AUTO LOCK”.
Vertical white lines appear when
shooting a very bright object.
● This sometimes occurs when the contrast between the
background and the object is great. It is not a defect of the
camcorder.
Bright, crystal-shaped spots appear
in the viewfinder.
● Sunlight is directly entering the lens. This is not a defect of
the camcorder.
The viewfinder and the lens have
become dirty (ex. fingerprints).
● Wipe them gently with soft cloth.
An error number (i.e. E03) appears.
● Turn the camcorder’s power off, then disconnect the
power source. After a few minutes, try turning the power
on again. If the error number still appears, consult your
nearest JVC dealer.
The image is out of focus.
● The diopter needs to be adjusted (੬ pg. 14).
● The scene being shot is adversely affecting the operation
of Auto Focus (੬ pg. 34).
Even though the Lens Cover is open,
the Lens Cover Warning indicator
blinks.
● The Lens Cover Warning indicator may blink when the
camcorder is used in dark areas, regardless of the position
of the Lens Cover.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit
(battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and
proceed as usual from the beginning.
EN
79
When the System Select Switch is set to “VIDEO”:
SYMPTOM
POSSIBLE CAUSE(S)
RECORDING
Recording cannot be performed.
● Make sure the Erase Protection tab is in the position that
allows recording. If not, slide the tab. Some cassettes have
removable tabs. If the tab has been removed, cover the
hole with adhesive tape (੬ pg. 17).
● If the System Select Switch is set to “D.S.C.”, it is not
possible to record onto the tape. Change the Switch
position to “VIDEO” (੬ pg. 18).
Recording does not start.
● The camcorder Power Switch has not been set to
“CAMERA” (੬ pg. 18).
PLAYBACK
The tape is running, but there’s no
playback picture.
● The TV has not been set to its VIDEO mode or channel.
● If A/V connection is used, the TV’s VIDEO/TV Switch has
not been set to VIDEO.
● The RF unit has not been set to the correct channel.
Playback cannot be performed.
● If the System Select Switch is set to “D.S.C.”, it is not
possible to play back a tape. Change the Switch position
to “VIDEO” (੬ pg. 40).
Playback picture is blurred or
interrupted.
● The video heads are dirty or worn out. Consult your
nearest JVC dealer for head cleaning or replacement.
The counter indication is blurred
during Still playback.
● This is normal.
TAPE TRANSPORT
The tape stops during fast-forward
or rewind.
● The Counter Memory Function has been activated
(੬ pg. 42).
Rewinding or fast-forwarding cannot
be performed.
● The tape is already fully wound on one reel or the other.
OTHER
The picture is blurred in the Quick
Review or Retake mode.
● This is normal while recording in the EP mode. Some noise
may be present while recording in the SP mode (੬pg. 16).
The date and time displays
disappear.
● If you remove the power source from the camcorder while
the power is on, all settings and selections are erased. Make
sure to turn the camcorder’s power off before disconnecting
the power source.
The wrong date and time are
displayed/recorded.
● If you have not performed Date/Time Setting (੬ pg. 13),
the date and time are not displayed/recorded correctly. Be
sure that Date/Time setting is carried out.
The tape won’t eject.
● The battery pack is running low.
TROUBLESHOOTING (cont.)
When the System Select Switch is set to “D.S.C.”:
80
EN
SYMPTOM
POSSIBLE CAUSE(S)
SHOOTING
Although the SNAPSHOT Button is
pressed, a still image is not stored in
the built-in memory.
● When the number of remaining shots available reaches
“0” (blinking), it becomes impossible to take your next
shot. Perform “DELETE” function to remove some still
images already stored in memory (੬ pg. 58).
Self-Timer Shooting is not available.
● Pressing the Recording Start/Stop Button does not start
recording in the Self-Timer Shooting procedure. Press the
SNAPSHOT Button (੬ pg. 49).
It is not possible to shoot in
sucession.
● A still image is in the process of being stored in memory
for approx. 2 seconds after the SNAPSHOT Button is
pressed. During that time, it is impossible to take another
shot. When the still image disappears and the scene you
are currently aimed at appears on the screen, take another
shot (੬ pg. 46).
PLAYBACK
Although “ALL” is selected in the
DELETE Menu Screen, all still images
cannot be deleted.
● The “Protect” function is in effect for some still images. If
they are not necessary, cancel the “Protect” function, then
try deleting all still images again (੬ pg. 57).
OTHER
Date/Time Insert is not performed
while shooting a still image.
● It is not possible to display the date/time on a still image.
● It is not possible to display the Instant Titles on a still image.
● It is not possible to set “REC TIME” in the Menu Screen.
Instant Titles are not displayed while
shooting a still image.
Some settings cannot be changed in
the Menu Screen.
Since the camcorder is a microcomputer-controlled device, external noise and interference (from a TV, a
radio, etc.) might prevent it from functioning properly. For example, when a still image you shot is stored
in the camcorder's built-in memory, the above may cause the following: Although the remaining number
of shots indicator shows that shooting is possible, a still image cannot be stored in memory after shooting.
In such a case, initialize the memory by following steps 1 through 3 below. Please note that initialization
deletes all the still images (including ones for which you performed the “Protect” function) stored in the
camcorder’s memory. If you wish to keep any of the still images that are stored in memory, before
initialization first transfer them to a PC and save them. If image data is corrupt, transfer is impossible.
1. Set the System Select Switch to “D.S.C.”, then set the Power Switch to
FORMAT
“PLAY”.
CANCEL
ENTER
2. Press the MODE Button for more than 5 seconds. The FORMAT Menu
Screen appears.
3. Rotate the MENU Jog Dial to move the highlight bar to “CANCEL” or
“ENTER”, then press it.
•“CANCEL” does not initialize the memory.
•“ENTER” initializes the memory. During initialization, “ENTER” blinks.
When initialization is complete, the screen becomes blue back.
Format Menu Screen
CAUTION:
While “ENTER” is selected and it is blinking, switching off the camcorder or removing the power supply
unit (battery pack or AC Power Adapter/Charger) may cause the camcorder’s built-in memory to become
corrupt. Never remove the power supply unit at this stage.
CAUTIONS
EN
81
DANGER:
Battery Packs
The supplied battery pack is a
nickel-cadmium battery. Before using
the supplied battery pack or an
optional battery pack, be sure to read
the following cautions:
Video Light
•The video light becomes extremely hot. Do not
touch it either while in operation or soon after
turning it off, otherwise serious injury may result.
•Do not place the camcorder into the carrying case
immediately after using the video light, since it
remains extremely hot for some time.
1. To avoid hazard . . .
.... do not burn.
Terminals
.... do not short-circuit the terminals.
.... do not modify or disassemble.
.... use only specified chargers.
•When operating, keep a distance of about 30 cm
(1 ft.) between the video light and people or
object.
2. To prevent damage and prolong service life . . .
.... do not subject to unnecessary shock.
.... avoid repeated charging without fully
discharging.
•Do not use near flammable or explosive materials.
•It is recommended that you consult your nearest
JVC dealer for replacing the video light.
.... charge in an environment where tempera-
tures are within the tolerances shown in the
chart below. This is a chemical reaction type
battery—cooler temperatures impede
chemical reaction, while warmer tempera-
tures can prevent complete charging.
.... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
.... avoid prolonged uncharged storage.
.... remove from charger or powered unit when
not in use, as some machines use current
even when switched off.
When using the AC Power Adapter/Charger in
areas other than the USA
Ⅲ The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an
AC wall outlet other than American National
Standard C73 series type use an AC plug adapter,
called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest JVC
dealer.
Plug adapter
NOTES:
●It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging.............. 10°C to 35°C (50°F to 95°F)
Operation ............ 0°C to 40°C (32°F to 104°F)
Storage ................ –10°C to 30°C (14°F to 86°F)
General Battery Precautions
•When the C-P6U or C-P7U (cassette adapter) is
not functioning even when correctly operated, the
battery is exhausted. Replace it with a fresh one.
•Use only the following battery:
●Recharging time is based on room temperature of
20°C.
●The lower the temperature, the longer recharging
takes.
C-P6U or C-P7U..................... AA (R6) size
Please make note of the following rules for battery
use. When misused, battery can leak or explode.
1. Refer to the C-P6U/C-P7U instructions when
replacing the battery.
2. Do not expose the battery to excessive heat as it
can leak or explode.
3. Do not dispose of battery in a fire.
4. Remove battery from the unit if it is to be stored
for an extended period to avoid battery leakage
which can cause malfunctions.
CAUTIONS (cont.)
82
EN
Cassettes
Main Unit
To properly use and store your cassettes, be sure to
read the following cautions:
1. During use . . .
1. For safety, DO NOT . . .
.... open the camcorder’s chassis.
.... disassemble or modify the unit.
.... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not
in use.
.... allow inflammables, water or metallic objects
to enter the unit.
.... remove the battery pack or disconnect the
power supply while the power is on.
.... leave the battery pack attached when the
camcorder is not in use.
.... make sure the cassette bears the VHS-C
mark.
.... be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
.... make sure the cassette is positioned properly
when inserting.
.... do not load and unload the cassette
repeatedly without allowing the tape to run
at all. This slackens the tape and can result in
damage.
.... do not open the front tape cover. This
exposes the tape to fingerprints and dust.
2. Avoid using the unit . . .
.... in places subject to excessive humidity or
dust.
.... in places subject to soot or steam such as
near a cooking stove.
.... in places subject to excessive shock or
vibration.
.... near a television set.
.... near appliances generating strong magnetic
or electric fields (speakers, broadcasting
antennas, etc.).
.... in places subject to extremely high (over
40°C or 104°F) or extremely low (under 0°C
or 32°F) temperatures.
2. Store cassettes . . .
.... away from heaters or other heat sources.
.... out of direct sunlight.
.... where they won’t be subject to unnecessary
shock or vibration.
.... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
.... vertically, in their original cases.
3. DO NOT leave the unit . . .
.... in places of over 50°C (122°F).
.... in places where humidity is extremely low.
(below 35%) or extremely high (above 80%).
.... in direct sunlight.
.... in a closed car in summer.
.... near a heater.
4. To protect the unit, DO NOT . . .
.... allow it to become wet.
.... drop the unit or strike it against hard objects.
.... subject it to shock or excessive vibration
during transportation.
.... keep the lens directed at extremely bright
objects for long periods.
.... direct the eyepiece of the viewfinder at the
sun.
.... carry it by holding the viewfinder. Be sure to
hold the main unit with both hands or use
the grip.
.... swing it excessively when using the shoulder
strap.
EN
83
How To Handle A CD-ROM
•Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or
back surface. If the CD-ROM gets dirty, gently
wipe it with a soft cloth outward from the center
hole using a circular motion.
•Do not use conventional disc cleaners or cleaning
spray.
•Do not bend the CD-ROM or touch its mirror
surface.
•Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
About moisture condensation . . .
● You may have observed that pouring a cold
liquid into a glass will cause drops of water to
form on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool
place to a warm place, after heating a cold
room, under extremely humid conditions or
in a place directly subjected to the cool air
from an air conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
SPECIFICATIONS
INPUT AND OUTPUT CONNECTORS
84
EN
GENERAL
Operating temperature : 0°C to +40°C
(32°F to 104°F)
Video
Audio
JLIP
: Output 1 Vp-p, 75 ohms,
unbalanced (via VIDEO
OUT connector)
: Output –8 dBs, 1 k-ohm
(via AUDIO OUT
connector)
Operating humidity
Storage temperature : –20°C to +50°C
(–4°F to 122°F)
Weight
Dimensions
(Including viewfinder) 222 (D) mm
: 35% to 80%
: Approx. 810 g (1.8 lbs)
: 113 (W) x 117 (H) x
: 3.5 mm diameter, 4-pole,
mini-head jack
(4-1/2” x 4-5/8” x 8-3/4”)
Digital
: Mini DIN 8-pin
Speaker
: 20 mm round x 1,
monaural
: DC 6V
External microphone
input
: –68 dBs, high impedance
unbalanced with ø3.5 mm
(MONO)
Power source
Power consumption
light on
light off
Signal system
: 8.6 W
: 5.7 W
: NTSC-type
AC POWER ADAPTER/BATTERY CHARGER
(AA-V15U)
Power requirement
: AC 110 V to 240 V`,
SYSTEM
50/60 Hz
Camcorder format
Video recording system
Luminance
: VHS NTSC standard
Power consumption : 23 W
Output
Charge
VTR
Charging system
: FM recording
: Converted sub-carrier
direct recording
: DC 8.5 V
: DC 6.3 V
, 1.3 A
, 1.8 A
Color
: Constant current, peak
detection, timer controlled
: 140 (W) x 42 (H) x
68 (D) mm
(5-9/16” x 1-11/16” x
2-11/16”)
: Approx. 300 g (0.71 lbs)
Conforms to VHS standard
Cassette
Tape speed
:
cassette
Dimensions
SP
EP
: 33.35 mm/sec. (1-5/16 ips)
: 11.12 mm/sec. (7/16 ips)
Recording time (max.)
Weight
SP
EP
: 40 minutes
: 120 minutes
(with TC-40 cassette)
CASSETTE ADAPTER (C-P7U)
Dimensions
: 188 (W) x 25 (H) x
104 (D) mm
(7-7/16” x 1” x 4-1/8”)
: Approx. 240 g (0.53 lbs)
: “AA (R6)” – size battery x 1
D.S.C. format
Recording format : Digital data storage
(based on JPEG)
Recording medium : Built-in flash memory,
1 Mbyte
Number of
storable shots
Weight
Accessory
Provided Accessories ...................... ੬ pg. 9
: FINE mode:
Optional Accessories
approx. 22 shots
(approx. 32000 byte data
compression)
•Battery Packs BN-V12U, BN-V22U, BN-V25U
•Car Battery Charger BH-V3U
•Battery Charger BH-VC10U
•Car Battery Cord AP-V7U
•RF Unit RF-V5U
•Compact VHS-C Cassettes TC-40/30/20
•Active Carrying Bag CB-V7U
•Remote Control Unit RM-V700U
STANDARD mode:
approx. 44 shots
(approx. 16000 byte data
compression)
Image size
: 320 x 240 pixels
CAMERA
Pick up
Lens
: 1/4” format CCD
Some accessories are not available in some areas.
Please consult your nearest JVC dealer for details on
accessories and their availability.
:
F1.6, f = 3.8 to 83.6 mm,
22:1 power zoom lens with
auto iris and macro control,
filter diameter 46 mm
Specifications shown are for SP mode unless
otherwise indicated.
E. & O. E. Design and specifications subject to
change without notice.
Viewfinder
: Electronic viewfinder with
0.5” black/white CRT
White balance
adjustment
: Auto/Manual adjustment
EN
VICTOR COMPANY OF JAPAN, LIMITED
0P4ri9n8teMdSinV*JaUpNan*YP
UM
COPYRIGHT© 1998 VICTOR COMPANY OF JAPAN, LTD.
|