owner’s manual
5.25-inch (130 mm) Coaxial Speaker System
Thank you for choosing a JL Audio Evolution™ C5 Coaxial Speaker System
for your automotive sound system.
These Evolution™ Speakers have been designed and manufactured to
exacting standards in order to ensure years of musical enjoyment in your
vehicle. For maximum performance, we highly recommend that you have
your new speakers installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the speakers yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443-1100 during business hours.
C5-525x sPeCIFICaTIons
Woofers: Cast Alloy Frame, Patented Elevated Frame Cooling
(U.S. Patent #6,219,431 & #6,229,902), DMA-Optimized Motor
System, Mineral-Filled Polypropylene Cone, Butyl Rubber
Surround, 1-in. / 25 mm Voice Coil, Kapton® Former, Low-
Profile, Symmetrical Roll Spider, Ferrite Magnet
Included Components and Parts:
• Two C5-525x 5.25-inch (130 mm) Coaxial Speakers
• Two C5-525x-XO Crossover Networks
• Two Metal Woofer Grilles with ABS Grille Trays
• Two Self-Adhesive JL Audio Nameplates for Grilles
• Butyl Adhesive Putty for Woofer Grilles
Tweeters: 0.75 in. / 19 mm Silk Soft Dome
• Twelve #8 x 1.25 inch (32 mm) Sheet Metal Screws
• Eight Mounting Clips for Woofer Mounting
• Two 6.4 mm Female Crimpable Connectors
• Four 4.7 mm Female Crimpable Connectors
• Two 2.8 mm Female Crimpable Connectors
• Twelve Crimpable Spade Connectors
Ferrofluid Cooling and Damping, Neodymium Magnet
Crossover Networks: 2-way network with 2nd order
low-pass and 2nd order high-pass circuit, premium Mylar®
capacitors, air-core inductors, 4-position adjustable tweeter
output level, 3-position midrange presence control,
Polyswitch tweeter protection
Continuous Power Handling: 75 Watts (RMS Method)
Peak Music Power: 225 Watts
Recommended Power Range: 25-150 Watts (RMS)
Frequency Response: 53 Hz - 25 KHz ( 3 dB)
Efficiency @ 1W/1m: 88.5 dB @ 1W/1m
Nominal Impedance: 4 ohms
Due to ongoing product development, all specifications are subject to change without notice.
3
GeTTInG sTarTeD
TweeTer ProTeCTIon
•ꢀꢀTurnꢀoffꢀtheꢀaudioꢀsystem.ꢀItꢀisꢀalsoꢀ
advisableꢀtoꢀdisconnectꢀtheꢀnegativeꢀ(–)ꢀ
terminalꢀofꢀyourꢀvehicle’sꢀbatteryꢀwheneverꢀ
performingꢀinstallationꢀwork.
•ꢀꢀBeforeꢀcutting,ꢀdrillingꢀorꢀinsertingꢀanyꢀscrew,ꢀ
checkꢀclearancesꢀonꢀbothꢀsidesꢀofꢀtheꢀplannedꢀ
mountingꢀsurface.ꢀAlsoꢀcheckꢀforꢀanyꢀpotentialꢀ
obstacles,ꢀsuchꢀasꢀwindowꢀtracksꢀandꢀmotors,ꢀ
wiringꢀharnesses,ꢀetc.ꢀCheckꢀbothꢀsidesꢀofꢀtheꢀ
TheꢀC5ꢀcrossoverꢀnetworksꢀareꢀequippedꢀwithꢀ
anꢀadvancedꢀelectronicꢀtweeterꢀprotectionꢀcircuitꢀ
designedꢀtoꢀminimizeꢀtheꢀpossibilityꢀofꢀtweeterꢀ
failure.ꢀThisꢀelectronicꢀdeviceꢀmonitorsꢀcurrentꢀgoingꢀ
toꢀtheꢀtweeterꢀandꢀwillꢀdisconnectꢀtheꢀtweeterꢀfromꢀ
theꢀsignalꢀwhenꢀitꢀsensesꢀoverload.ꢀShouldꢀthisꢀoccurꢀ
whileꢀlisteningꢀtoꢀtheꢀaudioꢀsystem,ꢀsimplyꢀreduceꢀtheꢀ
volumeꢀforꢀaꢀfewꢀsecondsꢀandꢀtheꢀprotectionꢀcircuitꢀ
willꢀresetꢀitselfꢀautomatically.
vehicle,ꢀmanyꢀvehiclesꢀareꢀnotꢀsymmetrical!
•ꢀꢀAlwaysꢀwearꢀprotectiveꢀeyewear.
CrossoVer neTworK aDJusTmenT
Theꢀcrossoverꢀnetworksꢀhaveꢀbeenꢀdesignedꢀtoꢀ
allowꢀtonalꢀadjustmentsꢀtoꢀtheꢀupperꢀmidrangeꢀ
responseꢀandꢀtweeterꢀlevel.ꢀTheseꢀadjustmentsꢀmakeꢀ
itꢀpossibleꢀtoꢀfine-tuneꢀyourꢀsystemꢀtoꢀsuitꢀyourꢀ
listeningꢀpreferencesꢀandꢀtoꢀcompensateꢀforꢀvariousꢀ
speakerꢀmountingꢀapplications.ꢀ
CrossoVer neTworK InsTallaTIon
TheꢀcrossoverꢀnetworksꢀsuppliedꢀwithꢀyourꢀC5ꢀ
Systemꢀshouldꢀbeꢀinstalledꢀinꢀaꢀdryꢀlocationꢀinsideꢀ
yourꢀvehicle.ꢀDOꢀNOTꢀINSTALLꢀTHEMꢀINSIDEꢀOFꢀ
AꢀDOOR!ꢀDoorsꢀoftenꢀgetꢀwetꢀonꢀtheꢀinside,ꢀwhichꢀ
canꢀdamageꢀyourꢀcrossoverꢀnetworksꢀandꢀcouldꢀ
potentiallyꢀdamageꢀyourꢀentireꢀsoundꢀsystem.ꢀTheꢀ
crossoversꢀcanꢀbeꢀscrewedꢀintoꢀaꢀsolidꢀsurfaceꢀviaꢀtwoꢀ
holesꢀlocatedꢀunderꢀtheꢀprotectiveꢀcoverꢀofꢀtheꢀcase.ꢀ
Toꢀaccessꢀtheseꢀholes,ꢀsimplyꢀsqueezeꢀtheꢀsidesꢀofꢀtheꢀ
coverꢀwhileꢀgentlyꢀpullingꢀtheꢀcoverꢀawayꢀfromꢀtheꢀ
base.ꢀMakeꢀsureꢀthatꢀyourꢀmountingꢀlocationꢀwillꢀnotꢀ
causeꢀdamageꢀtoꢀwiring,ꢀfuelꢀlines,ꢀbrakeꢀlinesꢀorꢀanyꢀ
otherꢀvitalꢀcomponentꢀofꢀyourꢀvehicle.ꢀOnceꢀyouꢀhaveꢀ
screwedꢀtheꢀcaseꢀinꢀandꢀmadeꢀyourꢀconnections,ꢀsnapꢀ
theꢀprotectiveꢀcoverꢀbackꢀintoꢀplace.ꢀ
ꢀ
WARNING
!!
It is absolutely vital that your component system
is connected as shown in this manual. Failure to
connect the system as shown may result in damage to
your speakers which is NOT covered under warranty.
Do not substitute different crossover networks into
your C5 System. Do not use crossover networks
intended for different C5 models.
Amplifier
Input
4 | JL Audio - C5-525x Owner’s Manual
aDJusTaBle mIDranGe PresenCe
aDJusTaBle TweeTer leVel
YourꢀC5ꢀcrossoverꢀnetworksꢀprovideꢀaꢀuniqueꢀ
midrangeꢀpresenceꢀcontrol,ꢀlocatedꢀunderꢀtheꢀcover.ꢀ
Theꢀmidrangeꢀpresenceꢀisꢀselectableꢀviaꢀaꢀsetꢀofꢀpinsꢀ
andꢀallowsꢀforꢀthreeꢀsettings.ꢀTheseꢀsettingsꢀaffectꢀtheꢀ
amplitudeꢀofꢀtheꢀupperꢀmidrangeꢀresponseꢀofꢀtheꢀC5ꢀ
componentꢀwoofer.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀ
yourꢀlisteningꢀinꢀtheꢀ“REF”ꢀ(Reference)ꢀandꢀadjustꢀ
upꢀorꢀdownꢀasꢀneededꢀtoꢀcompensateꢀforꢀmountingꢀ
location,ꢀorientationꢀorꢀpersonalꢀtaste.
C5ꢀcrossoverꢀnetworksꢀalsoꢀprovideꢀfourꢀlevelsꢀ
ofꢀtweeterꢀadjustabilityꢀdesignedꢀtoꢀcompensateꢀforꢀ
differentꢀmountingꢀlocations,ꢀvehicleꢀinteriorsꢀandꢀ
personalꢀtaste.ꢀTheseꢀlevelsꢀareꢀselectableꢀviaꢀaꢀsetꢀofꢀ
pinsꢀlocatedꢀunderꢀtheꢀclearꢀcoverꢀofꢀeachꢀcrossoverꢀ
case.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀlisteningꢀinꢀtheꢀ
“REF”ꢀ(Reference)ꢀposition.ꢀToꢀfindꢀtheꢀoptimumꢀ
tonalꢀbalanceꢀinꢀyourꢀinstallation,ꢀexperimentꢀwithꢀ
alternateꢀtweeterꢀlevelꢀsettingsꢀbyꢀmovingꢀtheꢀpins.ꢀItꢀ
isꢀsafeꢀtoꢀswitchꢀjumpersꢀwhileꢀtheꢀsystemꢀisꢀplaying.
Red
Black
5
WARNING
!!
sPeaKer PlaCemenT ConsIDeraTIons
Inꢀmostꢀcases,ꢀyourꢀspeakersꢀwillꢀbeꢀplacedꢀ
ꢀ
Double check the clearance for both speakers
before proceeding. Many cars are different from
one side to the other!
intoꢀfactoryꢀspeakerꢀlocations.ꢀIfꢀyouꢀhaveꢀsomeꢀ
speakerꢀmountingꢀflexibility,ꢀkeepꢀtheꢀfollowingꢀ
inꢀmind:Lowerꢀmountingꢀlocations,ꢀsuchꢀasꢀtheꢀ
lowerꢀfrontꢀcornerꢀofꢀaꢀdoorꢀorꢀaꢀkick-panelꢀprovideꢀ
theꢀgreatestꢀpathꢀlengthꢀdistancesꢀforꢀtheꢀsoundꢀ
emittedꢀbyꢀtheꢀspeakers.ꢀForꢀthisꢀreason,ꢀtheyꢀareꢀ
generallyꢀmoreꢀdesirableꢀthanꢀhigherꢀmountingꢀ
locations.ꢀHigherꢀmountingꢀlocationsꢀwillꢀusuallyꢀ
resultꢀinꢀextremeꢀnear-sideꢀsoundstageꢀbiasꢀwhichꢀ
compromisesꢀtheꢀstereoꢀlisteningꢀexperience.ꢀ
sPeaKer InsTallaTIon
Theꢀspeakerꢀshouldꢀbeꢀinstalledꢀinꢀoneꢀofꢀtheꢀ
followingꢀwaysꢀdependingꢀonꢀlocation:
ꢀ
Factory location:ꢀRunꢀspeakerꢀwireꢀtoꢀtheꢀdesiredꢀ
mountingꢀlocations.ꢀIfꢀyouꢀareꢀrunningꢀwiresꢀintoꢀ
aꢀdoor,ꢀuseꢀexistingꢀfactoryꢀwiringꢀbootsꢀwheneverꢀ
possible.ꢀIfꢀyouꢀareꢀdrillingꢀnewꢀholes,ꢀfileꢀtheirꢀedgesꢀ
andꢀinstallꢀrubberꢀgrommetsꢀintoꢀeachꢀhole.ꢀWiresꢀ
shouldꢀthenꢀbeꢀcoveredꢀwithꢀaꢀprotective,ꢀflexibleꢀ
PVCꢀsleeveꢀandꢀthenꢀrunꢀthroughꢀtheꢀdoorꢀjamb.ꢀ
Makeꢀsureꢀthatꢀtheꢀwiresꢀwillꢀclearꢀdoorꢀhingesꢀandꢀ
otherꢀstructuresꢀinꢀtheꢀdoor.ꢀIfꢀyouꢀareꢀunsureꢀaboutꢀ
anyꢀpartꢀofꢀthisꢀprocess,ꢀpleaseꢀcontactꢀyourꢀꢀ
JLꢀAudioꢀdealerꢀforꢀinstallationꢀhelp.ꢀ
Yourꢀnewꢀspeakersꢀhaveꢀbeenꢀdesignedꢀtoꢀinstall,ꢀ
withoutꢀmodifications,ꢀintoꢀmostꢀvehiclesꢀthatꢀacceptꢀ
aꢀ5.25-inchꢀ(130ꢀmm)ꢀspeaker.ꢀMostꢀfactoryꢀ5.25ꢀꢀꢀꢀ
-inchꢀspeakersꢀuseꢀfourꢀmountingꢀscrewsꢀwhichꢀwillꢀ
lineꢀupꢀwithꢀtheꢀmountingꢀholesꢀonꢀyourꢀwoofers.ꢀ
Itꢀisꢀabsolutelyꢀvitalꢀthatꢀtheꢀspeakerꢀframeꢀ
fitsꢀintoꢀtheꢀmountingꢀholeꢀcleanly.ꢀThisꢀmustꢀbeꢀ
checkedꢀpriorꢀtoꢀtighteningꢀtheꢀscrews.ꢀDoꢀnotꢀ
forceꢀtheꢀframeꢀintoꢀaꢀholeꢀthatꢀisꢀtooꢀsmall.ꢀDoꢀ
notꢀtightenꢀtheꢀspeakerꢀontoꢀanꢀunevenꢀsurface.ꢀ
Thisꢀwillꢀdamageꢀyourꢀspeakers.ꢀTheꢀspeakerꢀ
shouldꢀalsoꢀfitꢀsoꢀthatꢀairꢀdoesꢀnotꢀleakꢀaroundꢀ
theꢀmountingꢀflange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀ
degradationꢀinꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀ
withꢀanꢀautomotive-gradeꢀsealantꢀmaterial.
Connectꢀtheꢀspeakerꢀwiresꢀtoꢀbothꢀsetsꢀofꢀ
terminalsꢀonꢀeachꢀspeaker,ꢀobservingꢀcorrectꢀ
polarityꢀandꢀmakingꢀsureꢀthatꢀtheꢀtweeterꢀandꢀ
wooferꢀwiresꢀcorrespondꢀtoꢀtheꢀcorrectꢀterminalsꢀ
onꢀbothꢀtheꢀspeakerꢀandꢀtheꢀcrossover.ꢀ
Secureꢀtheꢀspeakerꢀandꢀgrilleꢀtrayꢀ(ifꢀdesired)ꢀ
toꢀtheꢀpanelꢀbyꢀevenlyꢀtighteningꢀbyꢀhandꢀ
mountingꢀscrews.ꢀUseꢀtheꢀsuppliedꢀmountingꢀ
clipsꢀandꢀtheꢀtheꢀprovidedꢀ#8ꢀxꢀ1.25ꢀinchꢀ(32ꢀ
mm)ꢀmountingꢀscrewsꢀunlessꢀtheꢀfactoryꢀ
holesꢀalreadyꢀfeatureꢀthreadedꢀinserts.ꢀ
6 | JL Audio - C5-525x Owner’s Manual
DIaGram D: FaCTory loCaTIon wooFer InsTallaTIon
WARNING
!!
Optional
Hand-tighten the screws evenly in a criss-cross
pattern to avoid bending the speaker frame or
stripping the mounting clips.
7
Custom location:ꢀRunꢀspeakerꢀwireꢀtoꢀtheꢀdesiredꢀ
mountingꢀlocations.ꢀIfꢀyouꢀareꢀrunningꢀwiresꢀintoꢀ
aꢀdoor,ꢀuseꢀexistingꢀfactoryꢀwiringꢀbootsꢀwheneverꢀ
possible.ꢀIfꢀyouꢀareꢀdrillingꢀnewꢀholes,ꢀfileꢀtheirꢀ
edgesꢀandꢀinstallꢀrubberꢀgrommetsꢀintoꢀeachꢀhole.ꢀ
Wiresꢀshouldꢀthenꢀbeꢀcoveredꢀwithꢀaꢀprotective,ꢀ
flexibleꢀPVCꢀsleeveꢀandꢀthenꢀrunꢀthroughꢀtheꢀdoorꢀ
jamb.ꢀMakeꢀsureꢀthatꢀtheꢀwiresꢀwillꢀclearꢀdoorꢀ
hingesꢀandꢀotherꢀstructuresꢀinꢀtheꢀdoor.ꢀIfꢀyouꢀ
areꢀunsureꢀaboutꢀanyꢀpartꢀofꢀthisꢀprocess,ꢀpleaseꢀ
contactꢀyourꢀJLꢀAudioꢀdealerꢀforꢀinstallationꢀhelp.ꢀ
Double check the clearance for both
Secureꢀtheꢀspeakerꢀandꢀgrilleꢀtrayꢀtoꢀtheꢀ
panelꢀbyꢀevenlyꢀtighteningꢀbyꢀhandꢀtheꢀprovidedꢀ
#8ꢀxꢀ1.25ꢀinchꢀ(32ꢀmm)ꢀmountingꢀscrews.ꢀ
Breakꢀoffꢀsmallꢀpiecesꢀofꢀtheꢀsuppliedꢀbutylꢀadhesiveꢀ
puttyꢀandꢀplaceꢀthemꢀonꢀtheꢀinsideꢀofꢀeachꢀgrilleꢀ
tray.ꢀThisꢀadhesiveꢀwillꢀholdꢀtheꢀgrilleꢀmeshꢀinsertꢀ
inꢀplaceꢀfirmlyꢀandꢀpreventꢀrattling.ꢀInsertꢀtheꢀgrilleꢀ
meshꢀinsertꢀintoꢀtheꢀgrilleꢀtray,ꢀsqueezingꢀgentlyꢀ
aroundꢀitsꢀedgeꢀuntilꢀitꢀseatsꢀfirmlyꢀintoꢀtheꢀtray.ꢀ
Finally,ꢀattachꢀtheꢀself-adhesiveꢀJLꢀAudioꢀlogoꢀ
badgeꢀtoꢀtheꢀgrilleꢀmeshꢀinsert.
speakers before proceeding.
Selectꢀanꢀevenꢀsurface.ꢀTighteningꢀaꢀspeakerꢀontoꢀ
anꢀunevenꢀsurfaceꢀcanꢀdamageꢀit.ꢀUseꢀtheꢀsuppliedꢀ
templateꢀtoꢀmarkꢀtheꢀdesiredꢀmountingꢀlocation.ꢀ
Markꢀtheꢀcenterꢀandꢀtheꢀoutlineꢀofꢀtheꢀmountingꢀ
holeꢀasꢀwellꢀasꢀtheꢀmountingꢀscrewꢀpositions.ꢀ
Beforeꢀdrillingꢀorꢀcuttingꢀonꢀyourꢀinteriorꢀpanels,ꢀ
useꢀaꢀutilityꢀknifeꢀtoꢀcutꢀanyꢀfabric,ꢀvinylꢀorꢀleatherꢀ
fromꢀholeꢀlocations.ꢀTheseꢀmaterialsꢀcanꢀeasilyꢀ
beꢀsnaggedꢀbyꢀaꢀdrillꢀorꢀaꢀsaw,ꢀcausingꢀdamageꢀtoꢀ
theꢀpanelꢀandꢀpossibleꢀbodilyꢀinjury.ꢀDrillꢀfourꢀ
1/8-inchꢀ(3ꢀmm)ꢀholesꢀforꢀtheꢀspeaker’sꢀmountingꢀ
screwsꢀatꢀtheꢀpositionsꢀyouꢀhaveꢀmarked.ꢀAlsoꢀdrillꢀ
aꢀpilotꢀholeꢀinꢀtheꢀcenterꢀofꢀtheꢀspeakerꢀmountingꢀ
holeꢀatꢀthisꢀtime.ꢀThen,ꢀusingꢀaꢀsaberꢀsaw,ꢀmakeꢀ
theꢀcircularꢀcutꢀoutꢀforꢀtheꢀspeaker.ꢀFileꢀanyꢀroughꢀ
edges.ꢀInsertꢀtheꢀmountingꢀclipsꢀwithꢀtheꢀflatꢀsideꢀ
towardsꢀtheꢀspeakerꢀasꢀshownꢀinꢀtheꢀDiagramꢀE.
Itꢀisꢀabsolutelyꢀvitalꢀthatꢀtheꢀspeakerꢀframeꢀ
fitsꢀintoꢀtheꢀmountingꢀholeꢀcleanly.ꢀThisꢀmustꢀbeꢀ
checkedꢀpriorꢀtoꢀtighteningꢀtheꢀscrews.ꢀDoꢀnotꢀ
tightenꢀtheꢀspeakerꢀontoꢀanꢀunevenꢀsurface!ꢀThisꢀ
willꢀdamageꢀyourꢀspeakers.ꢀTheꢀspeakerꢀshouldꢀ
alsoꢀfitꢀsoꢀthatꢀnoꢀairꢀleaksꢀaroundꢀtheꢀmountingꢀ
flange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀdegradationꢀ
inꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀwithꢀsilicone,ꢀ
ropeꢀcaulkꢀorꢀsimilarꢀsealantꢀmaterial.ꢀ
Connectꢀtheꢀspeakerꢀwiresꢀtoꢀbothꢀsetsꢀofꢀ
terminalsꢀonꢀeachꢀspeaker,ꢀobservingꢀcorrectꢀ
polarityꢀandꢀmakingꢀsureꢀthatꢀtheꢀtweeterꢀandꢀ
wooferꢀwiresꢀcorrespondꢀtoꢀtheꢀcorrectꢀterminalsꢀ
onꢀbothꢀtheꢀspeakerꢀandꢀtheꢀcrossover.ꢀ
8 | JL Audio - C5-525x Owner’s Manual
DIaGram e: CusTom loCaTIon wooFer InsTallaTIon
WARNING
!!
Hand-tighten the screws evenly in a criss-cross
pattern to avoid bending the speaker frame or
stripping the mounting clips.
9
noTes
10 | JL Audio - C5-525x Owner’s Manual
noTes
11
lImITeD warranTy - auTomoTIVe sPeaKer sysTems (usa)
JLꢀAUDIOꢀwarrantsꢀtheseꢀspeakersꢀ(andꢀcrossoverꢀnetworks,ꢀwhereꢀapplicable)ꢀtoꢀbeꢀfreeꢀofꢀdefectsꢀinꢀ
materialsꢀandꢀworkmanshipꢀforꢀaꢀperiodꢀofꢀone (1) year.
Thisꢀwarrantyꢀisꢀnotꢀtransferableꢀandꢀappliesꢀonlyꢀtoꢀtheꢀoriginalꢀpurchaserꢀfromꢀanꢀauthorizedꢀꢀ
JLꢀAUDIOꢀdealer.ꢀꢀShouldꢀserviceꢀbeꢀnecessaryꢀunderꢀthisꢀwarrantyꢀforꢀanyꢀreasonꢀdueꢀtoꢀmanufacturingꢀ
defectꢀorꢀmalfunction,ꢀJLꢀAUDIOꢀwillꢀ(atꢀitsꢀdiscretion),ꢀrepairꢀorꢀreplaceꢀtheꢀdefectiveꢀproductꢀwithꢀnewꢀorꢀ
remanufacturedꢀproductꢀatꢀnoꢀcharge.ꢀDamageꢀcausedꢀbyꢀtheꢀfollowingꢀisꢀnotꢀcoveredꢀunderꢀwarranty:ꢀaccident,ꢀ
misuse,ꢀabuse,ꢀproductꢀmodificationꢀorꢀneglect,ꢀfailureꢀtoꢀfollowꢀinstallationꢀinstructions,ꢀunauthorizedꢀrepairꢀ
attempts,ꢀmisrepresentationsꢀbyꢀtheꢀseller.ꢀꢀThisꢀwarrantyꢀdoesꢀnotꢀcoverꢀincidentalꢀorꢀconsequentialꢀdamagesꢀ
andꢀdoesꢀnotꢀcoverꢀtheꢀcostꢀofꢀremovingꢀorꢀreinstallingꢀtheꢀunit(s).ꢀꢀCosmeticꢀdamageꢀdueꢀtoꢀaccidentꢀorꢀnormalꢀ
wearꢀandꢀtearꢀisꢀnotꢀcoveredꢀunderꢀwarranty.
Anyꢀapplicableꢀimpliedꢀwarrantiesꢀareꢀlimitedꢀinꢀdurationꢀtoꢀtheꢀperiodꢀofꢀtheꢀexpressꢀwarrantyꢀasꢀprovidedꢀ
hereinꢀbeginningꢀwithꢀtheꢀdateꢀofꢀtheꢀoriginalꢀpurchaseꢀatꢀretail,ꢀandꢀnoꢀwarranties,ꢀwhetherꢀexpressꢀorꢀimplied,ꢀ
shallꢀapplyꢀtoꢀthisꢀproductꢀthereafter.ꢀꢀSomeꢀstatesꢀdoꢀnotꢀallowꢀlimitationsꢀonꢀimpliedꢀwarranties,ꢀthereforeꢀ
theseꢀexclusionsꢀmayꢀnotꢀapplyꢀtoꢀyou.ꢀꢀThisꢀwarrantyꢀgivesꢀyouꢀspecificꢀlegalꢀrights,ꢀandꢀyouꢀmayꢀalsoꢀhaveꢀotherꢀ
rightsꢀwhichꢀvaryꢀfromꢀstateꢀtoꢀstate.
ꢀ
If you need service on your Jl auDIo product:
AllꢀwarrantyꢀreturnsꢀshouldꢀbeꢀsentꢀtoꢀJLꢀAUDIOꢀfreightꢀprepaidꢀthroughꢀanꢀauthorizedꢀJLꢀAUDIOꢀ
dealerꢀandꢀmustꢀbeꢀaccompaniedꢀbyꢀproofꢀofꢀpurchaseꢀ(aꢀcopyꢀofꢀtheꢀoriginalꢀsalesꢀreceipt.)ꢀꢀDirectꢀ
returnsꢀfromꢀconsumersꢀorꢀnon-authorizedꢀdealersꢀwillꢀbeꢀrefusedꢀunlessꢀspecificallyꢀauthorizedꢀbyꢀ
JLꢀAUDIOꢀwithꢀaꢀvalidꢀreturnꢀauthorizationꢀnumber.ꢀꢀWarrantyꢀexpirationꢀonꢀproductsꢀreturnedꢀ
withoutꢀproofꢀofꢀpurchaseꢀwillꢀbeꢀdeterminedꢀfromꢀtheꢀmanufacturingꢀdateꢀcode.ꢀCoverageꢀmayꢀbeꢀ
invalidatedꢀasꢀthisꢀdateꢀisꢀpreviousꢀtoꢀpurchaseꢀdate.ꢀꢀReturnꢀonlyꢀdefectiveꢀcomponents.ꢀꢀIfꢀoneꢀspeakerꢀ
failsꢀinꢀaꢀsystem,ꢀreturnꢀonlyꢀthatꢀspeakerꢀcomponent,ꢀnotꢀtheꢀentireꢀsystem.ꢀNon-defectiveꢀitemsꢀ
receivedꢀwillꢀbeꢀreturnedꢀfreight-collect.ꢀꢀCustomerꢀisꢀresponsibleꢀforꢀshippingꢀchargesꢀandꢀinsuranceꢀ
inꢀsendingꢀtheꢀproductꢀtoꢀJLꢀAUDIO.ꢀꢀFreightꢀdamageꢀonꢀreturnsꢀisꢀnotꢀcoveredꢀunderꢀwarranty.ꢀ
For service Information in the u.s.a. please call
Jl audio Customer service: (954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Jl audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025
International warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
C5-525x-02082008
|