Eclipse Fujitsu Ten CD5405 User Manual

OWNER'S MANUAL�

CUSTOMER NOTICE

Please retain this booklet and write in the serial number

of your CD5405 for identification.

The serial number is labeled or stamped on the chassis.

Serial No.

CD5405

ESN E5 High-Power CD Receiver

We appreciate your purchase of this receiver.

Please read through this manual for correct operation.

We suggest that after reading it you keep this manual

in a safe place for future reference.

FUJITSU TEN LIMITED

Contact:FUJITSU TEN CORP. OF AMERICA

19600 So. Vermont Avenue, Torrance, CA 90502

Call:800-233-ECLIPSE

"ECLIPSE" is a registered trademark of

FUJITSU TEN LIMITED in 48 countries

including the U.S. and Japan.

www.eclipse-web.com

(

)

090001-14660700 0411MT F.O

For your safety in using the

CD5405

Warnings and caution signs, illustrated below, are posted

throughout this manual as well as on the CD5405. They show safe

and correct ways to handle the product so as to prevent personal

injury to you, others and to avoid property damage.

Before reading through the manual, take time to read through and

learn the important information listed in this section.

This sign indicates a situation in which

incorrect handling or disregard of this sign

might result in death or serious personal injury.

Warning

This sign indicates a situation in which

incorrect handling or disregard of this sign

Caution

might result in personal injury or may result

solely in damage to property.

Warning

• Do not modify this system for use other than that specified

herein. Also, do not deviate from the installation procedures

described herein; Eclipse will not be held liable for damages

including, but not limited to serious injury, death or property

damage resulting from installations that enable unintended

operation.

• This equipment requires 12V DC and should only be installed in

a vehicle with a 12V negative ground electrical system. Any

other installation may cause a fire or other severe damage to

the equipment and the vehicle.

• Never install this equipment where it will interfere with safe

operation of the vehicle. Never block the driver's view. Do not

install equipment where it may interfere with operation of the

brakes, the steering or any safety equipment, including seat

belts and air bags.

• When installing equipment do not remove or alter existing

vehicle fasteners, including nuts, bolts, screws, clips, and

fittings. Never detach, move or alter existing vehicle wiring,

including electrical grounds and straps. Alteration of existing

vehicle components may make vehicle unsafe to operate.

Warning

• Before installation, remove the negative (-) battery terminal to

prevent shocks, electrical arcing, fires, and damage to vehicle

wiring and the equipment you are installing.

• Secure wiring with tape or plastic ties so that wires do not

interfere with vehicle operation, including brake pedal, gear

shifter and steering. Position wires so that they will not be

rubbed, abraded, or damaged by moving vehicle components,

including power seats.

• To avoid equipment and vehicle damage, including fire, never

supply power to installed equipment in a way which will

overload the capacity of an existing vehicle circuit. Never

leave a power supply wire or connection uninsulated. Always

install supplied fuses, circuit breakers, and relays.

• Air bags are vital safety equipment. Never install equipment in

a way which will alter air bag wiring or interfere with air bag

deployment. Air bags must function properly in the event of an

accident.

• For your protection, never use a power drill without safety

glasses or goggles. Debris or broken drill bits may cause

severe eye injuries, including blindness.

• Use electrical tape to insulate the ends of all wires, even if not

used. Proper insulation prevents arcs, shocks and fires.

• Some equipment uses batteries. Never install equipment

where young children can get access to batteries. If a battery

is swallowed, seek medical attention immediately.

• When vehicle is moving, never take your eyes off the road to

make adjustments to the equipment. You must pay attention to

the road to avoid accidents, do not let the operation or

adjustment of the equipment distract you from proper vehicle

operation.

• The driver should not look at the screen while driving.

Accidents may result if you are not paying attention to the

forward direction.

• Do not put foreign objects in the loading slot of disc. Fires or

shocks may result.

• Do not disassemble or alter this equipment. Accidents, fires or

shocks may result.

Warning

• Do not let water or foreign objects enter the internal parts of this

equipment. Smoke, fires or shocks may result.

• Pay attention to where the remote control is left. Traffic

accidents or problems with driving may result if the remote

control makes its way under the brake pedal etc. when the

vehicle is stopped or when it goes around a corner.

• Do not use when it is broken (the screen is not lit or no sound

comes out). Accidents, fires or shocks may result.

• Always replace fuses with fuses of identical capacity and

characteristics. Never use a heavier fuse than the original.

Using the wrong type of fuse may cause a fire or severe

damage.

• If foreign objects or water enters the equipment, smoke comes

out, or there is a strange odor, stop using it immediately, and

contact your dealer. Accidents, fires, or shocks may result if

you continue to use it in these conditions.

• The driver should not change the CD while driving. As

accidents may result if you are not paying attention to the

forward direction, first stop the car at a safe location and then

proceed.

• Plastic bags and wrappings may cause suffocation and death.

Keep away from babies and children. Never put bag over your

head or mouth.

Caution

•

Wiring and installing this equipment requires expertise and

experience. Professional installation is recommended. Consult

with your dealer or a professional installer. Incorrect wiring may

damage the equipment or interfere with safe vehicle operation.

Use only the accessory parts as specified. Using other parts may cause

damage to the equipment or cause parts to fall or fly off the equipment.

• Do not install the unit in places where it may get dew

condensation on (around the air conditioning hose, etc.), come

in contact with water, or in condition of high moisture, dust or

oily smoke. If water, moisture, dust or oily smoke enters this

unit, smoke, fires or malfunctions may result.

Caution

• Avoid installing in places where it cannot be fastened securely

or where there are strong vibrations. Also, if you installed the

unit with double-sided tape, first wipe away dirt and wax from

the installation area. Otherwise, the unit may come loose due

to vibration while driving, causing problems for driving and

resulting in traffic accidents or injuries.

•

Do not install in places with direct sunlight or where it will be hit

directly by hot air from the heater. This may increase the temperature

of the interior of this equipment, resulting in fires and malfunctions.

•

Do not block the fan, heat sink or vents for this unit. When fan, heat

sink or vent is blocked, the interior overheats, and fires may result.

• Connect as specified in the installation manual. If not

connected normally, fires or accidents may result.

• When installing in vehicles equipped with air bags, check the

manufacturer's cautions regarding operation before operating.

Airbags may not operate properly.

• Carry out the wiring such that cords are not pinched by

movable parts such as seat rails, and screw parts of the vehicle

body. Accidents, fires and shocks may result from

disconnection and electrical shorts.

• Carry out the wiring such that the cord does not make contact

with metal parts. The cord is may be damaged by contact with

metal parts, resulting in fire and shocks.

• Avoid hot surfaces when wiring equipment. High temperatures

may damage wiring, causing shorts, arcing and fires.

• When changing the installation location for this equipment,

please consult the dealer where you bought it for safety

reasons. Expertise is necessary for removal and installation.

• Keep volume to a reasonable level so that you can hear sounds

from outside the vehicle, including warning sounds, voices, and

sirens. Failure to do so may cause an accident.

• Do not put your hands or fingers into the loading slot of disc.

Injuries may result.

• Do not touch the heat dissipating part of the amp. Burns may

result from the heat of this part.

• Do not recharge dry batteries. Dry batteries may rupture,

resulting in injuries.

Caution

• Do not use batteries other than those specified. Also, do not

mix old and new batteries. Injuries or pollution to the

surroundings may result from battery ruptures and leakage.

• When inserting batteries into the equipment, be careful of the

polarity (positive/negative), and insert them as indicated. If the

battery polarities are incorrect, injuries and pollution to the

surroundings may result from battery ruptures and leakage.

• Replace used batteries as soon as possible; they may leak and

damage equipment. Battery leakage can burn your skin or

your eyes. Wash hands after handling.

•

If alkaline solution from alkaline dry batteries makes contact with your

skin or clothes, flush with clean water. If any of the solution gets in your

eyes, also flush clean with water and then seek medical attention.

•

When disposing of lithium dry batteries, affix insulating tape to

the positive and negative terminals, and after they are insulated,

dispose of them according to the "Local municipal directives".

Shorts, fires and ruptures may result from disposal together with

other electrically conductive objects such as metal parts, etc.

•

Do not short, disassemble or heat the batteries, or place them in fire or

water. Fire and injuries may result from battery rupture and leakage.

• Store the remote control in a place away from direct sunlight,

high temperatures, and high moisture levels. The case may

change shape, and the batteries may rupture and leak.

• Do not use this equipment except for in-vehicle use. Shocks or

injuries may result.

• Be careful of the position of the volume when turning the power

source ON. Hearing damage may result if very loud noise is

emitted when the power is turned ON.

• Do not operate under abnormal conditions such as when the

sound is broken or distorted. Fires may result.

• This equipment uses invisible laser light. Do not disassemble

or alter this equipment. If trouble occurs, contact the dealer

where you bought the equipment. Altering this equipment may

cause exposure to laser emissions (worsening eyesight), or

result in accidents, fires or shocks.

• If the equipment is dropped or the cabinet is broken, turn off

the power to the main unit and contact your dealer. If used in

this condition, fires or shocks may result.

Table of Contents

Operating precautions ............................................. 10

Notes on operation ..................................................................... 10

About compact discs .................................................................. 11

About cleaning a CD .................................................................. 13

Names of controls and parts .................................. 14

ESN security operating procedure ......................... 15

About ESN .................................................................................. 15

How to operate the ESN (Key CD) security ................................ 16

How to program the Key CD ................................................ 16

How to cancel the Key CD ................................................... 17

How to change the Key CD .................................................. 18

How to resume normal operation (ESN security lock out) ... 18

What happens if an incorrect CD is inserted? ...................... 19

How to turn the security indicator on/off ..................................... 20

How to read the Electronic Serial Number ................................. 20

Basic operation ........................................................ 21

Turning the power on and off ..................................................... 21

Listening to a CD ........................................................................ 22

Listening to the tuner .................................................................. 23

Adjusting audio volume .............................................................. 24

Switching audio control modes ................................................... 25

VOL (VOLUME) Mode ......................................................... 25

BASS Mode ......................................................................... 25

MID (MIDDLE) Mode ........................................................... 26

TREB (TREBLE) Mode ........................................................ 26

BAL (BALANCE) Mode ........................................................ 26

FAD (FADER) Mode ............................................................ 26

NON-F (NON-FADER) Mode ............................................... 26

NF-P (NON-PHASE) Mode .................................................. 27

LOUD Mode ......................................................................... 27

Storing user presets for the equalizer ........................................ 27

Changing the equalizer mode .................................................... 28

Making changes with Function Mode ......................................... 29

Disabling the guide tone feature (for button operation) ........ 29

Setting the time .................................................................... 30

Changing the LINE OUT mode ............................................ 31

How to operate the CD player ................................. 32

Listening to CDs ......................................................................... 32

Advancing to the next track or returning to the beginning of the

track being played ...................................................................... 33

Fast Forward/Rewind ................................................................. 33

Playing the beginning of tracks (SCAN) ..................................... 33

Repeating the same track (REPEAT) ......................................... 34

Playing tracks in random order (RANDOM) ............................... 34

Ejecting the disc ......................................................................... 35

Switching the display .................................................................. 35

How to operate the tuner ........................................ 36

Tuning to a station ...................................................................... 36

Entering stations into memory automatically

(The automatic preset mode: ASM) .......................................... 37

Manually setting stations into memory ....................................... 38

Preset station scan ..................................................................... 39

Switching the display .................................................................. 39

Changing the reception sensitivity for automatic scanning ........ 40

Changing the radio band location ............................................... 40

FM reception characteristics ...................................................... 41

FM reception differs from AM ............................................... 41

Fading out ............................................................................ 41

Reception area of FM broadcasts ........................................ 42

Multipath .............................................................................. 42

How to use an optional remote control ................. 43

Precautions in use of the remote control .................................... 43

Cleaning the remote control ....................................................... 43

Turning the power on/off ............................................................ 44

Adjusting the audio volume ........................................................ 44

Muting the volume ................................................................ 44

Switching playback modes ......................................................... 45

How to play the tuner ................................................................. 45

Selecting the FM/AM band ................................................... 45

Selecting a station (manually or automatically) .................... 46

Selecting preset stations ...................................................... 46

How to play CDs ......................................................................... 46

Switching disc mode ............................................................ 46

Advancing to the next track or returning to the beginning

of the track being played ...................................................... 47

Replacing the battery ................................................................. 48

If you have a question: ............................................ 49

Displayed information (for troubleshooting) ................................ 50

Specifications .......................................................... 53

Before installation ................................................... 54

Components ............................................................................... 54

Installation angle ........................................................................ 54

Mounting instruction ............................................... 55

Mounting the main unit ............................................................... 55

Names of lead wires and destinations ........................................ 58

System ....................................................................................... 59

How to contact customer service ............................62

Operating precautions

<Your CD5405 will perform well over a long period of time through correct

handling and care.>

Notes on operation

• For your safety, play only at volume levels that allow outside sounds to be

heard.

• We recommend using with this player a disc with

the logo shown to the left.

• You can play music CDs(CD-R/CD-RW) on this

player. Be sure to use discs that have been

properly processed.

Depending on the editing equipment used, some

discs may not play properly.

• CD-R and CD-RW discs recorded in the MP3 file

format are not playable.

• Do not insert anything other than a CD into the

disc slot.

Do not insert any foreign objects, such as coins or

credit cards, into the disc slot. Be especially

watchful of children’s mischief in this regard.

• Avoid severe mechanical shock.

When the player is subjected to severe vibration

while traveling over a rough surface, playback

may be intermittent. When a situation like this

occurs, resume playback after returning to a

smoother road.

• About dew condensation.

In cold or rainy weather, just as the interior glass

surface gets fogged, dew (water condensation)

may also settle on the deck. When this occurs,

disc playback may become intermittent or

impossible. Dehumidify the air in the vehicle for a

while before resuming playback.

• Cleaning the disc slot.

The disc slot tends to get dusty. Clean it

occasionally to prevent accumulated dust from

scratching the discs.

Operating precautions

About compact discs

• The signal recorded on a compact disc is read by a laser beam, so

nothing touches the disc surface. A scratch on the recorded surface or a

badly warped disc may cause deteriorated sound quality or intermittent

playback. Observe the following precautions to ensure high quality sound

performance:

• Do not leave an ejected disc in the disc slot

for very long; the disc may warp. Discs

should be stored in their cases and kept

away from high temperature and humidity.

• Do not stick a piece of paper or tape on, nor

write on or scratch either side of a disc.

• Discs spin at a high speed inside the deck.

Keep cracked or warped discs out of the

player to avoid damaging it.

• Avoid touching the recorded surface when

handling a disc; handle discs by their edges.

Operating precautions

About brand new CDs

About CD accessories

• You may notice that some brand

new discs are rough around the

center hole or outside edge.

Remove the rough edges with

the side of a ballpoint pen, etc.

Rough edges may prevent

proper loading in the deck.

Flakes from the rough edges

may also stick to the recorded

surface and interfere with

playback.

• Do not use accessories

(stabilizers, protective seals, laser

lens cleaners, etc.) sold for

“improving sound performance”

or “protecting CDs.” The changes

in CD thickness or outside

dimensions made by these

accessories may cause problems

in the player.

Rough Edges

Ballpoint

pen

• Please be sure NOT to attach any

ring-shape protector (or other

accessory) to your discs. Those

protectors are commercially

available and said to protect disc

and to improve sound quality

(and antivibration effect), but they

can do more harm than good in

regular uses. The most common

problems are disc insertion, disc

ejections, and won't play

problems due to the protector

ring that came off in the disc

mechanism.

Rough

Edges

Flakes

Recorded surface

Operating precautions

About borrowed CDs

About irregularly-shaped CDs

• Specially-shaped CDs, like

heart-shaped or octagonal CDs,

cannot be played. Do not

attempt to play them, even with

an adapter, since they may

damage the player.

• Do not use a CD with glue or

remnants of adhesive tape or

labels. They may cause the CD

to get stuck inside or damage

the deck.

How to remove CDs

• When removing the ejected disc,

pull it straight out along the slot.

Pressing downward in the

process may scratch the

recorded surface of the disc.

OKAY

About cleaning a CD

• Use a commercially available compact disc

cleaner to clean a CD, wiping lightly from the

center to the edge.

• Do not use benzine, thinner, LP record spray

or other cleaners on CDs. They may damage

a CD’s finish.

XXXX

Names of controls and parts

①

② ③

④

⑤⑥ ⑦ ⑧

⑭

⑨

⑬ ⑫

⑩ ⑧

⑪

Ejects compact disc.

[CD (EJECT) ] button

[DISC] button

Switches between disc modes.

Switches to radio mode and switches radio bands.

Inserts compact discs.

[FM AM] button

Disc slot

Switches screen display and turns function mode ON/OFF.

Sets the equalizer settings.

[DISP FUNC] button

[SOUND] button

[SEL] button

Selects radio stations and CD tracks.

Automatically finds radio reception or to fast forward/rewind.

Returns to previous screen.

[

] button

[RTN] button

Resets deck functions to default settings.

[RESET] button

Selects radio preset channels and performs disc mode

functions.

Buttons [1] to [6]

Adjusts volume and performs other functions.

Turns deck power ON/OFF.

[AUDIO CONTROL] button

[PWR] button

Mutes or cancels muting.

[MUTE] button

ESN security operating procedure

About ESN

This deck incorporates ESN (ECLIPSE Security Network). The ESN is

a security system which disables all deck functions when the power

is restored if the deck is stolen from the vehicle. Once the ESN is

activated, removing power to the deck or vehicle will activate the

security feature.

Setting or canceling of the security feature can be done with a "Key

CD". It is necessary to register a music CD as the "Key CD" in

advance.

ESN security operating procedure

Button [6]

[DISP FUNC] button

How to operate the ESN (Key CD) security

How to program the Key CD

Check that the the unit is in standby.

Press and hold button [6], then the [DISP FUNC]

button, and hold both for more than one second.

A [SEC] message appears, then in two seconds it will

change to [DISC].

The CD5405 is now ready to accept your Key CD in the

CD slot.

•If a CD has already been inserted, a [SEC] message appears,

ATTENTION

and then the CD is ejected.

•If a security is activated, programming the Key CD is not

available.

Insert the CD into the slot.

A [SEC] message appears, then the Key CD is ejected.

•If there is a problem with the inserted CD, an [ERR] message

will appear for two seconds and the CD will be ejected. Reinsert

the ejected CD.

ATTENTION

•If a CD causes the [ERR] message to appear twice in a row, a

[CHANGE] message will appear for two seconds. Try another

CD.

•Copy protected CD cannot be programmed for Key CD

security.

•The Security indicator will flash whenever the vehicle’s ignition

is switched off.

ESN security operating procedure

Button [6]

[DISP FUNC] button

How to cancel the Key CD

Check that the unit is in standby.

Press and hold button [6], then the [DISP FUNC]

button, and hold both for more than one second.

A [SEC] message appears, then in two seconds it will

change to [DISC].

The CD5405 is now ready to accept your Key CD in the

CD slot.

If a CD has already been inserted, a [SEC] message appears,

and then the CD is ejected.

ATTENTION

Insert your Key CD into the slot.

A [CANCEL] message appears, then the Key CD is

ejected.

The Key CD is canceled.

•This process cancels the protection for the ESN deck.

•If power to the ESN deck is disconnected, then reconnected, a

Key CD will not need to be inserted in order to return the unit to

normal operation.

ATTENTION

•Inserting a CD other than the Key CD will not cancel the

protection. Instead, the display [ERR] for two seconds, then the

normal CD playback mode will activate.

ESN security operating procedure

How to change the Key CD

First, cancel the existing Key CD.

Refer to “How to cancel the Key CD.”

Next, program a new Key CD.

Refer to “How to program the Key CD.”

How to resume normal operation (ESN security lock out)

If power is disconnected while ESN security is active (a Key

CD was programmed), operation is disabled until power is

restored and the unit unlocked. Follow this procedure to

resume normal operation.

When the power is turned on after disconnecting

the battery power, a [SEC] message will appear for

two seconds. Thereafter, the message changes to

[DISC] and the CD5405 is ready to accept your Key

CD into the slot.

Insert your Key CD into the slot.

If the correct CD is inserted, an [OK] message will

appear for two seconds and the CD will begin playing.

•If an incorrect CD is inserted, an [ERR_] ("ERR" and error

number) message will appear for two seconds, after which the

ATTENTION

CD will be ejected.

•If [ERR5] (the 5th time an error has occurred) appears, [HELP]

will appear, after which the CD will be ejected. When [HELP]

appears, carry out the operations for an ESN security lock out

by following the procedure in "What happens if an incorrect CD

is inserted?" (See next page).

•You must use the same CD used for Key CD programming; a

duplicate CD may not work properly.

ESN security operating procedure

Button [6]

[DISP FUNC] button

What happens if an incorrect CD is inserted?

After the 5th incorrect attempt, the display reads

[HELP] for five seconds.

[HELP] will appear for five seconds, after which the serial

number will appear.

Press button [6], then the [DISP FUNC] button, and

hold them for five seconds.

After the [SEC] message will appear for two seconds,

rolling code will appear.

Press the [DISP FUNC] button.

After the [SEC] message will appear for two seconds,

rolling code will appear.

Insert your Key CD into the slot.

If the correct CD is inserted, an [OK] message will

appear for two seconds and CD will be ejected.

•If an incorrect CD is inserted, an [ERR_] ("ERR" and error

number) message will appear for two seconds, after which the

ATTENTION

CD will be ejected.

•This process cancels the protection for the ESN deck.

G Note G

If after five tries the correct Key CD is not inserted, the display

reads [CALL800]; the unit must be returned to Eclipse to be

reset. In this case, please contact your Eclipse dealer for

assistance. For country-specific customer service information,

refer to "How to contact customer service" on page 62.

Your key CD can be easily forgotten. Write the

album name in a reminder note (See Page 67).

ESN security operating procedure

[DISP FUNC] button

Button [2]

Button [4]

How to turn the security indicator on/off

Once ESN security is activated, the indicator flashes whenever the

vehicle’s ignition is turned off, warning potential thieves that the unit

is protected. However, if you do not want this visible deterrent, it may

be turned off.

With the unit in standby, press button [2], then the [DISP

FUNC] button and hold both for more than one second.

[IND. FLASH] or [IND. -----] appears on the display.

[IND. FLASH] means the security indicator will flash when the

vehicle’s ignition is off, and [IND. -----] means it will not. Repeat

the above steps to reactivate the flash mode.

How to read the Electronic Serial Number

Check that the unit is in standby.

Press button [4], then the [DISP FUNC] button, and hold

both for more than one second.

[ESN] appears on the display, followed by an eight-digit

number; this number is your electronic serial number (ESN).

You may use this number to identify your Eclipse CD5405 in

the event it is recovered after being stolen.

Basic operation

[PWR] button

This section covers basic operating procedures. For additional

details, please refer to the sections on specific functions.

Turning the power on and off

Turning the power on and off.

When the power is turned on, the state used when the power was

turned off such as CD and tuner playback is restored.

When the vehicle has no ACC position on the ignition switch, care is

needed when turning off the deck. Follow Step 2 or Step 3 when

turning off the power.

When power is OFF, press the [PWR] button.

The power will come ON.

When the deck's power is turned on for the first time or if the

battery terminals have been disconnected because of a reason

ATTENTION

such as vehicle maintenance and the power is then turned back

on, the deck will start up in FM1 mode. After this, the broadcast

stations will be searched for automatically and stored in buttons

[1] to [6].

When power is ON, press the [PWR] button for less than

two seconds.

The power will go OFF and the deck will be in Standby.

If you press the [PWR] button again for more than one second,

the power will go completely off.

When power is ON, press the [PWR] button for more

than two seconds.

The power will go completely OFF.

If a car is not equipped with an ACC position (for example, a

European car), keep the [PWR] button depressed for more than

ATTENTION

two seconds.

Basic operation

[DISC] button

Listening to a CD

Insert a CD into the disc slot, label side up.

The CD will start playing.

When a CD is already loaded, press the [DISC] button to switch

to the CD mode.

ATTENTION

Basic operation

[FM AM] button

[

] button

[SEL]

button

[

] button

Buttons [1] to [6]

Listening to the tuner

Press the [FM AM] button.

This will turn the tuner on.

Press the [FM AM] button to switch to the desired FM or

AM bands.

Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in

order each time the button is pressed.

Turn the [SEL] button to the left or right to tune to a

station.

Turn to the right: Tunes to higher frequencies.

Turn to the left: Tunes to lower frequencies.

Press the [ ] or [ ] button to start the automatic station

search.

[

] button:

Starts searching toward higher frequencies.

Starts searching toward lower frequencies.

If stations have been stored in memory, pressing a button

from [1] to [6] will directly select a station. (Refer to the section

“Manually setting stations into memory” on page 38)

ATTENTION

Basic operation

[AUDIO CONTROL] button

[MUTE] button

Adjusting audio volume

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Increases the volume.

Turn to the left: Decreases the volume.

Press the [MUTE] button for less than one second to cut the

volume or restore it instantly.

ATTENTION

Warning

Do not adjust the volume or other controls while driving the

vehicle. Do so only while parked in a safe location.

Basic operation

[AUDIO CONTROL] button

Switching audio control modes

Various audio control modes may be fine-tuned using this

procedure.

Press the [AUDIO CONTROL] button for less than one

second to select the item to be adjusted.

Modes will switch in the order shown below each time the

button is pressed.

When the LINE OUT mode is REAR

VOL

BASS

MID

TREB

BAL

FAD LOUD

FAD

When the LINE OUT mode is NON-FEDER

VOL BASS MID TREB BAL

LOUD NF-P NON-F

VOL (VOLUME) Mode

Adjusts volume.

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Increases the volume.

Turn to the left: Decreases the volume.

BASS Mode

Adjusts bass level. Bass mode can be adjusted for each

source (CDP, FM and AM).

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Emphasizes low sounds.

Turn to the left: Softens low sounds.

Basic operation

[AUDIO CONTROL] button

MID (MIDDLE) Mode

Adjusts middle level. Mid mode can be adjusted for each

source (CDP, FM and AM).

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Emphasizes medium sounds.

Turn to the left: Softens medium sounds.

TREB (TREBLE) Mode

Adjusts treble level. Treble mode can be adjusted for each

source (CDP, FM and AM).

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Emphasizes high sounds.

Turn to the left: Softens high sounds.

BAL (BALANCE) Mode

Adjusts left/right speaker balance.

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Emphasizes right speakers.

Turn to the left: Emphasizes left speakers.

FAD (FADER) Mode

Adjusts front/rear speaker balance.

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Emphasizes front speakers.

Turn to the left: Emphasizes rear speakers.

NON-F (NON-FADER) Mode

Adjusts non-fader level (for connected sub-woofers, etc.).

Turn the [AUDIO CONTROL] button to the left or right.

Turn to the right: Increases level.

Turn to the left: Decreases level.

Basic operation

[AUDIO CONTROL] button

NF-P (NON-FADER PHASE) Mode

The merging of sound between the front and rear speakers and

the woofer can be improved by selecting the phase.

Switch the phase to a phase which lets the speakers combine

without any disharmony.

Turn the [AUDIO CONTROL] button to select NORMAL or

REVERSE.

NOR : Normal phase

REV : Reverse phase

LOUD Mode

The loudness control may be turned on to emphasize low and

high frequencies at low volume levels.

Loudness compensates for the apparent weakness of low and

high frequencies at low volume by boosting the bass and

treble levels.

Turn the [AUDIO CONTROL] button until the [LOUD ON]

display appears on the screen.

To disable the loudness feature, repeat the above procedure to

display the [LOUD OFF] indication.

ATTENTION

Storing user presets for the equalizer

The adjustment values for BASS, MIDDLE and TREBLE settings

made in the audio control mode can be stored. The stored

adjustment values can be called by changing the equalizer mode.

For detail, see "Changing the equalizer mode" on page 28.

Press the [AUDIO CONTROL] button for more than one

second.

The adjusted values are stored.

Basic operation

[SOUND] button

Changing the equalizer mode

EQ (equalizer) mode can be used to adjust the frequency of the

audio channels being played back in accordance with the genre and

instruments of the music being played. Apart from four equalizer

modes, this deck offers the audio adjustment mode in which you can

store set BASS, MIDDLE, and TREBLE adjustment values, and the

CUSTOM Mode in which and you can apply these adjustment

values.

Press the [SOUND] button for less than one second.

Each time the button is pressed, the equalizer mode changes

in the following order.

DEFEAT (equalizer OFF)

POWER (bass tones emphasized)

SHARP (high tones emphasized)

VOCAL (mid tones emphasized)

CUSTOM (stored user-preset values for the equalizer)

Basic operation

[DISP FUNC] button

[SEL] button

[RTN]

button

Making changes with Function Mode

A variety of settings can be changed.

Press the [DISP FUNC] button for more than one

second.

The function mode is activated.

Turn the [SEL] button in either direction to display setting

items for selection.

Setting items will be displayed in the following order when the

[SEL] button is turned to the right.

BEEP

CLOCK

LINE OUT

Disabling the guide tone feature (for button operation)

The receiver is set at the factory to emit a beep tone in

response to button operation. The guide tone feature may be

disabled in the following procedure:

Turn the [SEL] button to select BEEP.

Press the [SEL] button.

The Guide Tone Mode will be switched ON/OFF.

Turn the [SEL] button to select ON or OFF.

Press the [SEL] button to select current setting.

Press the [RTN] button.

At this time, other adjustments can also be made in

Function Mode.

Press the [DISP FUNC] or [RTN] button to exit

Function Mode.

Basic operation

[SEL] button

[RTN]

button

[DISP FUNC] button

Setting the time

This receiver uses the 12-hour display notation.

Turn the [SEL] button to select CLOCK.

Press the [SEL] button.

The clock adjustment mode is activated.

Press the [SEL] button to display the item to be

selected for adjustment.

Hours or minutes will be switched each time the button is

pressed.

Turn the [SEL] button to the left or right.

Turn to the right: Turns the time forward.

Turn to the left: Turns the time back.

Press the [RTN] button.

At this time, other adjustments can also be made in

Function Mode.

Press the [DISP FUNC] or [RTN] button to exit

Function Mode.

Basic operation

[SEL] button

[RTN]

button

[DISP FUNC] button

Changing the LINE OUT mode

When you select NON-F as the LINE OUT mode, you can make

the NON-F and NF-P settings in the audio control mode.

Turn the [SEL] button to select LINE OUT.

Press the [SEL] button.

Turn the [SEL] button to select REAR or NON-F.

Press the [SEL] button for more than five seconds.

Press the [RTN] button.

At this time, other adjustments can also be made in

Function Mode.

Press the [DISP FUNC] or [RTN] button to exit

Function Mode.

How to operate the CD player

[DISC] button

First press the [DISC] button to switch to the disc mode. It is

assumed here that a CD has already been loaded into the unit.

Listening to CDs

Press the [DISC] button.

This starts CD play.

Playback may be intermittent when there is a scratch on a CD or

when the recorded side is dirty.

Caution

How to operate the CD player

[SEL] button

[

] button

Button [4]

[

] button

Advancing to the next track or returning to

the beginning of the track being played

Turn the [SEL] button to the left or right.

Turn to the right: Advances to the next track.

Turn to the left: Returns to the beginning of the track being

played. (Repeat turning for previous tracks.)

Fast Forward/Rewind

Fast forward or rewind the song currently being played.

Press and hold the [ ] or [ ] button.

[

] button: Fast forward.

] button: Rewind.

Playing the beginning of tracks (SCAN)

Press button [4].

Pressing the button causes the player to move up to the next

track and play it for 10 seconds, then move up to the next track

and play it for 10 seconds, and so on until the button is

pressed again.

•To continue playing a desired track, press the button again to

stop scanning.

ATTENTION

•After the entire disc is scanned once, ordinary playback starts

from the point where scanning started.

How to operate the CD player

Buttons [5] and [6]

Repeating the same track (REPEAT)

Press button [5] to repeat the track being played.

To cancel, press button [5] again.

Playing tracks in random order (RANDOM)

Press button [6] to play the tracks in random order.

To cancel, press button [6] again.

•During random playback, press button [5] to repeat the track

ATTENTION

being played. To cancel repeat play (go back to random play),

press button [5] again.

During playback of a particular track: The track being played is

played repeatedly.

While searching: The following track is played repeatedly.

•Occasionally the same track happens to be played (selected)

two or more times in a row; this is normal operation and is not a

sign of a problem.

•When any of the functions - “Playing the beginning of tracks,”

“Repeating the same track” and “Playing tracks in random

order” - is selected, a message such as [SCAN], [REPEAT] or

[RANDOM] appears on the display to verify the current function.

How to operate the CD player

[DISP FUNC] button

[CD

(EJECT)] button

Ejecting the disc

Press the [CD

(EJECT)] button.

Disc is ejected.

Switching the display

Press the [DISP FUNC] button for less than one second.

Each time the button is pressed, the following will be displayed

in order.

Elapsed time ➔ Clock

How to operate the tuner

[SEL] button

] button

[FM AM] button

[

] button

First, press the [FM AM] button to start tuner operation.

There are automatic and manual methods for setting stations in

memory. The receiver will accept up to 24 stations in memory: 6 in

AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting)

Tuning to a station

Press the [FM AM] button to switch to the desired FM or

AM bands.

Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in

order each time the button is pressed.

Turn the [SEL] button to the left or right to tune to a

station.

Turn to the right: Tunes to higher frequencies.

Turn to the left: Tunes to lower frequencies.

Press the [ ] or [ ] button to start the automatic station

search.

[

] button:

Starts searching toward higher frequencies.

Starts searching toward lower frequencies.

At times, it may be difficult to maintain optimum reception

because the antenna affixed to your vehicle is in motion

constantly (relative to the broadcast antenna), encountering

continuous variation in the received radio signals’ strength. Other

factors affecting reception include interference from natural

obstacles, sign posts, etc.

ATTENTION

How to operate the tuner

[FM AM] button

[SEL]

button

Buttons [1] to [6]

Entering stations into memory automatically

(The automatic preset mode: ASM)

Press the [FM AM] button to switch to the desired FM or

AM bands.

Radio bands will switch from FM1 ➔ FM2 ➔ FM3 ➔ AM in

order each time the button is pressed.

Press the [SEL] button for more than two seconds until a

beep is heard.

The automatic preset mode starts.

The [ASM ON] indicator on the screen flashes, and stations are

automatically entered in memory under buttons [1] to [6].

These buttons are called preset buttons.

•Pressing the preset buttons ([1] to [6]) allows you to make one-

touch station selections. The frequency of the selected station

ATTENTION

is indicated on the display.

•When a new station is set in memory, the station previously set

in memory will be deleted.

•If there are fewer than six receivable stations, the stations set in

the remaining buttons will be retained.

If the vehicle’s battery is disconnected (for repairs to the vehicle

or for removing the receiver), all stations in memory will be lost.

Caution

In such a case, set stations in memory again.

How to operate the tuner

[FM AM] button

[SEL]

button

Buttons [1] to [6]

Manually setting stations into memory

This section covers the setting of stations in memory under the

numbered buttons.

Press the [FM AM] button to switch between FM and AM.

Turn the [SEL] button to the right or left to tune to the

station to be entered in memory.

Select any button, from [1] to [6], and press it for more

than two seconds.

The tuned station is now memorized and set in the button

selected. Repeat the procedure to set additional manually

tuned stations in memory, in turn, for buttons [1] to [6]. These

buttons are called the preset buttons.

•Pressing the preset buttons ([1] to [6]) allows you to make one-

touch station selections. The frequency of the selected station

ATTENTION

is indicated on the display.

•When a new station is set in memory, the station previously set

in memory will be deleted.

If the vehicle’s battery is disconnected (for repairs to the vehicle

or for removing the receiver), all stations in memory will be lost.

Caution

In such a case, set stations in memory again.

How to operate the tuner

[SEL]

button

[DISP FUNC] button

Buttons [1] to [6]

Preset station scan

This function enables reception of all the stations in the preset

buttons for five seconds each.

Press the [SEL] button for less than one second.

[P SCAN] will appear on the display, and stations stored under

preset buttons [1] through [6] will be played for five seconds

each.

To stop the preset scan mode at a desired station, press

the [SEL] button again.

The receiver will stay tuned to the desired station.

Switching the display

Press the [DISP FUNC] button for less than one second.

Each press of the button switches the display the clock and

current frequency.

How to operate the tuner

[FM AM] button

Buttons [1] and [3]

Changing the reception sensitivity for automatic scanning

The deck lets you select the reception sensitivity to be used for

automatic scanning of stations. The two sensitivity modes available

for this deck are AUTO mode and DX mode.

During automatic scanning, the reception sensitivity

switches automatically to one of two levels. Initially the

reception sensitivity is set to the low level so that only

stations with strong signals are received. If no stations

could be received, the reception sensitivity is increased

so that stations with weaker signals can also be

received.

AUTO Mode

DX Mode

Because the reception sensitivity for automatic scanning

is set to the high level from the start, even stations with

weaker signals can be received. (Signal crossover may

result in some stations being hard to hear.)

Check that the deck is in standby mode.

Press and hold the [FM AM] button, then button [1], and

hold both for more than three seconds.

The mode switches between AUTO mode and DX mode each

time the buttons are pressed.

Changing the radio band location

The location for the radio bands used between the North America

region and the Asia/Australia/Latin region can be switched. The

default setting is USA (North America).

Check that the deck is in standby mode.

Press and hold the [FM AM] button, then button [3], and

hold both for more than three seconds.

The radio band switches between USA, ASIA, AUS and LATIN

each time the buttons are pressed.

After changing the location, the power will turn on in FM1

mode. After this, the broadcast stations will be searched for

automatically and stored in buttons [1] to [6].

How to operate the tuner

FM reception characteristics

In general, FM has much better tonal quality than AM. However, FM

and FM stereo reception encounter several characteristic problems

not encountered with AM. FM is more difficult to receive than AM in a

moving vehicle. The following are explanatory notes on what to

expect from FM reception and on how to get satisfactory

performance.

FM reception differs from AM

A characteristic of transmitted signals is that lower frequencies

travel further. FM frequencies are much higher than AM’s

(similar to a ray of light): they won’t bend but they will reflect.

Often, they will be interrupted by tall buildings, mountains, etc.,

taking direct and indirect paths to your vehicle’s antenna. The

distance at which FM stations can be received satisfactorily is

usually not nearly as far as that which AM stations can be

received.

AM Radio Waves

Ionosphere

FM Radio Waves

Ionosphere

Fading out

In weak signal or “fringe” reception areas, FM stations may

fade out completely, or fade in and out. When driving in weak

signal areas, such as near hills, through valleys or tunnels,

among tall buildings, etc., you may encounter unusual noise

interference. THIS IS NOT A TUNER PROBLEM. In this case,

you can only wait until you are in a better reception area, tune

to a stronger station, or reduce the treble level.

How to operate the tuner

Reception area of FM broadcasts

A home receiver can catch weak FM stereo signals through the

use of a tall, directional or ultra-sensitive antenna. In a moving

vehicle, the area for good reception is limited because of

varying conditions encountered while driving, including the

types and heights of broadcast antenna structures, signal

strength, engine noise, etc. For best reception with manual

antenna, extend the antenna mast as far as possible.

Transmitting Antenna 100 Meters High

Effective Radiation Power 1kW

FM Stereo Auto Radio 12.4 miles

FM Monaural Auto Radio 31 miles

Home FM Stereo Receiver 62 miles

Reception quality varies depending on the power of the FM

station, natural and artificial barriers,weather conditions, etc.

Multipath

The reflection characteristics of FM waves cause another

problem called multipath–FM wave signals reflecting off of

buildings, mountains, etc. When the antenna receives direct

and reflected waves at the same time, distortion of sound in the

treble range often occurs, such as static or harsh-sounding

voices. THIS IS NOT A TUNER PROBLEM. Only moving to

another area with a clearer signal path can remedy the

situation.

DIRECT

WAVE

How to use an optional remote control

Precautions in use of the remote control

• Be careful when handling the remote control, especially

because it is small and light. Dropping or striking it hard may

damage it, wear out the battery or cause a malfunction.

• Keep the remote control free of moisture, dust and water. Do

not subject it to shock.

• Do not place the remote control unit where it will get hot, such

as on the dashboard or near a heater vent. Allowing the

remote control unit to overheat may warp its case or cause