OWNER’S
MANUAL
SX525
SX570
SX650
models SX690
LIMITED TWO-YEAR CONSUMER WARRANTY
Directed Electronics, Inc. promises to the
original purchaser, to replace this product
should it prove to be defective in workman-
ship or material under normal use, for a
period of two years from the date of
purchase from the dealer as indicated by the
date code marking of the product PROVIDED
the product was installed by an authorized
Directed dealer. During this two-year period,
there will be no charge for this replacement
PROVIDED the unit is returned to DEI, ship-
ping pre-paid. If the unit is installed by
anyone other than an authorized Directed
dealer, the warranty period will be one year
from the date of purchase by the dealer as
indicated by the date code marking of the
product. This warranty is non-transferable
and does not apply to any unit that has been
modified or used in a manner contrary to its
intended purpose, and does not cover
damage to the unit caused by installation or
removal of the unit. During this one-year
period, there will be no charge for this
replacement PROVIDED the unit is returned
to DEI, shipping pre-paid. This warranty is
void if the product has been damaged by
accident or unreasonable use, neglect,
improper service or other causes not arising
out of defects in materials or construction.
Units which are found to be damaged by
abuse resulting in thermally damaged voice
coils are not covered by this warranty but
may be replaced at the absolute/sole discre-
tion of DEI. ALL WARRANTIES INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTIC-
ULAR PURPOSE, AND WARRANTY OF NON-
INFRINGEMENT OF INTELLECTUAL PROPERTY
ARE EXPRESSLY EXCLUDED TO THE
MAXIMUM EXTENT ALLOWED BY LAW, AND
DEI NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON TO ASSUME FOR IT ANY
LIABILITY IN CONNECTION WITH THE SALE
OF THE PRODUCT. DEI HAS ABSOLUTELY NO
LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING ITS AUTHORIZED
DEALERS OR INSTALLERS. Unit must be
returned to DEI, postage pre-paid, with bill of
sale or other dated proof of purchase bearing
the following information: consumer's name,
telephone number, and address, authorized
dealer's name and address, and product
description. Note: This warranty does not
cover labor costs for the removal and rein-
stallation of the unit. IN ORDER FOR THIS
WARRANTY TO BE VALID, YOUR UNIT MUST
BE SHIPPED WITH PROOF OF INSTALLATION
BY AN AUTHORIZED DEI DEALER. ALL UNITS
RECEIVED BY DEI FOR WARRANTY REPAIR
WITHOUT PROOF OF DEI DEALER INSTALLA-
TION WILL BE COVERED BY THE LIMITED 1
YEAR PARTS AND LABOR WARRANTY. Note:
This warranty does not cover labor costs for
the removal and reinstallation of the unit. BY
PURCHASING THIS PRODUCT, THE
CONSUMER AGREES AND CONSENTS THAT
ALL DISPUTES BETWEEN THE CONSUMER
AND Directed SHALL BE RESOLVED IN ACCOR-
DANCE WITH CALIFORNIA LAWS IN SAN
DIEGO COUNTY, CALIFORNIA.
3
© 2004 Directed Electronics, Inc
FEATURES
Woofer
Tweeter
„ Low resonate mineral-filled vacuum-
„ New hotter 19mm ferrofluid cooled
silk dome tweeter with neodymium
magnet (6x9 25mm).
formed polypropylene cone
„ Fiberglass-reinforced injection-molded
basket.
Crossover
„ High-grade neodymium motor
„ 6 dB/octave passive crossover with
structure for higher efficiency.
tweeter protection.
WARNING
High-powered car audio
systems may produce sound
pressure levels that exceed the
threshold at which hearing loss may
result.
They may also impair a driver’s ability to
hear traffic sounds or emergency vehi-
cles. Use common sense and practice
safe listening habits when listening to or
adjusting your audio system.
SOUND QUALITY
Obtaining the highest quality sound
reproduction in the mobile environment
requires installation techniques and
knowledge of vehicle interiors that go
far beyond simple replacement of stock
speakers. Speaker location, orientation,
phasing, and the vehicles interior mate-
rials are important considerations when
designing and installing an auto sound
system.
To achieve the best sound quality
possible from your Directed Audio loud-
speakers, Directed recommends the
installation be performed by an MECP
certified technician.
4
© 2004 Directed Electronics, Inc
INSTALLATION PRECAUTIONS
The Directed SX neodymium separates
are designed for installation into factory
speaker locations, custom mounting
enclosures or any flat mounting surface
inside the vehicle with sufficient rear
clearance. The following precautions and
instructions cover the basic and most
common types of installation.
distortion or shorting of the speaker
leads to the chassis ground. Over-
sized holes will not allow the
mounting screws to make sufficient
contact with the panel, allowing the
speaker to become loose.
„ Always protect the wires when
routing by avoiding sharp metal
edges, moving parts such as heater
or vent controls, clutch pedals, brake
pedals, steering columns, and power
window motors and gears.
„ Check behind panels for clearance of
metal brackets, hoses, and wire
harnesses before making any cuts.
„ When mounting speakers into doors,
roll the window up and down to
check clearance of the glass and
window regulator.
„ When routing wires through metal
panels and doorjambs always use
vinyl tubing and grommets for
protection and a professional-looking
installation.
„ Make sure the mounting holes are
the correct size for the speaker.
Undersized holes can cause speaker
5
© 2004 Directed Electronics, Inc
FIGURE 6—CONNECTION/ADJUSTMENT SINGLE AMPLIFIER
BREAK AWAY
RIM
The model SX570 speaker has a break
away rim to facilitate mounting as either
a 6 X 8 or a 5 X 7 speaker. The
mounting size required varies depending
on the vehicle manufacturer.
Break away the plastic using a pair of
pliers. Use care not to damage the
speaker cone or tweeter.
The excess flashing left after removal of
the rim may require clean-up.
6
© 2004 Directed Electronics, Inc
SPECIFICATIONS
Model
System
SX525
SX570
SX650
SX690
60Hz–21kHz
60 watts
120 watts
4 Ohms
Frequency response
Power handling RMS
Power handling peak
Impedance
Magnet weight
Vas
80Hz–21kHz 80Hz–21kHz 75Hz–21kHz
40 watts
80 watts
4 Ohms
30.2 g
3.4L
40 watts
80 watts
4 Ohms
30.2 g
5.4L
50 watts
100 watts
4 Ohms
30.2 g
7.3L
40.5 g
16.6L
Fs
Qts
80 Hz
0.53
80 Hz
0.64
75 Hz
0.63
60 Hz
0.66
89dB
2.5”
8-7/8”x6”
Efficiency (1W/1M)
Mounting depth
Mounting hole diameter
88dB
1.75”
5”
88dB
2”
5”x7”
89dB
1.8”
5.66”
Common Driver Specifications
Magnet type
Magnet diameter
Voice coil former
Voice coil diameter
Voice coil layers
Tweeter
Neodymium Neodymium Neodymium Neodymium
25mm (1”) 25mm (1”) 25mm (1”) 31mm (1.25”)
Kapton
1”
Kapton
1”
Kapton
1”
Kapton
1”
4
4
4
4
19mm (3/4”) 19mm (3/4”) 25mm (1”)
Size
Fs
19mm (3/4”)
1.9kHz
1.9kHz
91dB
1.9kHz
91dB
2.1kHz
92dB
Efficiency (1W/1M)
Crossover
91dB
6 dB/octave 6 dB/octave 6 dB/octave
with tweeter with tweeter with tweeter
6 dB/octave
with tweeter
protection
protection
protection
protection
7
© 2004 Directed Electronics, Inc
Quality Directed products are sold and serviced throughout North America and around the world
Call 800 274 0200 for more information about our products and services
© 2004 Directed Electronics, Inc.
-
All rights reserved
-
G34010.15.20.25 12-04
|