ENGLISH
CONTENTS
AUTOMATIC DEMONSTRATION
GETTING STARTED
DIGITAL VIDEO CAMERA
6
7 – 14
TAPE
RECORDING & PLAYBACK
15 – 24
GR-DVL867
GR-DVL865
GR-DVL767
GR-DVL765
GR-DVL567
GR-DVL367
GR-DVL365
GR-DVL167
GR-DVL160
TAPE RECORDING ........................ 16 – 20
TAPE PLAYBACK .......................... 21 – 24
MEMORY CARD
RECORDING & PLAYBACK
25 – 36
MEMORY CARD RECORDING ......... 26 – 27
MEMORY CARD PLAYBACK ............ 28 – 29
ADVANCED FEATURES .................... 30 – 36
ADVANCED FEATURES
37 – 66
FOR RECORDING ........................... 38 – 45
USING MENUS FOR
DETAILED ADJUSTMENT .............. 46 – 51
DUBBING ..................................... 52 – 53
USING THE REMOTE CONTROL UNIT... 54 – 64
SYSTEM CONNECTIONS.................. 65 – 66
REFERENCES
67 – Back Cover
DETAILS ............................................. 68
TROUBLESHOOTING ...................... 69 – 73
USER MAINTENANCE ............................ 74
CAUTIONS .................................... 75 – 77
SPECIFICATIONS ........................... 78 – 79
INDEX ......................................... 80 – 86
TERMS ............................... 87 – Back Cover
Please visit our Homepage on the World Wide Web and
answer our Consumer Survey (in English only):
For Accessories:
The camcorder illustrations
appearing in this instruction
manual are of the
GR-DVL867.
Memory card recording
features are available on
GR-DVL867, GR-DVL865,
GR-DVL767, GR-DVL765,
GR-DVL567, GR-DVL367
and GR-DVL365
INSTRUCTIONS
EN
LYT0909-001B
EN
3
CAUTIONS:
● This camcorder is designed to be used with PAL-type colour television signals. It cannot be used for
playback with a television of a different standard. However, live recording and LCD monitor/viewfinder
playback are possible anywhere.
●
Use the JVC BN-V408U/V416U/V428U battery packs and, to recharge them or to supply power to the
camcorder from an AC outlet, use the provided multi-voltage AC Adapter and Power Cord. (An appropriate
conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides
to allow for ventilation (10 cm or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
4
EN
SAFETY PRECAUTIONS
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to the camcorder and to the user.
When carrying, be sure to always securely attach and use the provided shoulder strap. Carrying or holding the
camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a malfunction.
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the camcorder, as
they are particularly susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving the unit on top of the TV is not
recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.
Ⅲ This camcorder is designed exclusively for the digital video cassette, SD Memory Card and
MultiMediaCard. Only cassettes marked “
” can be used with this unit.
” and memory cards* marked “
” or
“
Before recording an important scene . . .
.... make sure you only use cassettes with the Mini DV mark
.... make sure you only use memory cards* with the mark
.
or
.
.... remember that this camcorder is not compatible with other digital video formats.
.... remember that this camcorder is intended for private consumer use only. Any commercial use without
proper permission is prohibited. (Even if you record an event such as a show, performance or
exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
* Memory cards can be used with GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only.
EN
5
PROVIDED ACCESSORIES
or
AAA (R03) Battery
x 2 (for remote
control unit)
Power Cord
Battery Pack
BN-V408U
AC Adapter AP-V10EG,
AP-V11EG or AP-V12EG
or
Cable Adapter
Lens Cap
Shoulder Strap
CD-ROM
Remote
Control Unit
RM-V717U
(See below for
(GR-DVL867/DVL865/
DVL767/DVL765/
DVL567/DVL367/
DVL365/DVL167 only)
attachment)
PC Connection Cable
(GR-DVL167 only)
Memory Card 8 MB
(GR-DVL867/DVL865/
DVL767/DVL765/
DVL567/DVL367/DVL365
only) (Already inserted
in the camcorder)
Audio/Video Cable
(ø3.5 mini-plug to
RCA plug)
USB Cable (GR-DVL867/
DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only)
Editing Cable
GR-DVL167/DVL160:
One plug has 3 rings
around the pin, and the
other has 1 ring around
the pin.
Core Filter x 1
GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365:
Both plugs have 1 ring
around the pin.
(for PC Connection cable
provided with optional
HS-V16KITE software;
GR-DVL160 only ੬ pg. 6
for attachment)
Lens hood (Already
Core Filter x 1
attached to the camcorder;
GR-DVL867/DVL865/
DVL767/DVL765 only)
(for optional S-Video
cable ੬ pg. 6 for
attachment)
NOTE:
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more
core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.
How To Attach The Lens Cap
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
NOTE:
To confirm the lens cap is on correctly make sure the cap is flush to the camera.
1
2
3
For GR-DVL867/
DVL865/DVL767/
DVL765 Owners:
The lens cap can be
attached only when
the lens hood is
attached to the
camcorder.
6
EN
How To Attach The Core Filter
Attach the Core Filter(s) (if provided with your model ੬ pg. 5) to an optional cable(s). The Core Filter
reduces interference.
3 cm
Stopper
Wind once
Release the
stoppers on both
ends of the Core
Filter.
Run the cable through the Core Filter, leaving approx.
3 cm of cable between the cable plug and the Core Filter.
Wind the cable once around the outside of the Core Filter
as shown in the illustration.
Close the Core Filter until it
clicks shut.
• Wind the cable so that it is not slack.
NOTE:
Take care not to damage the cable.
Ⅲ When connecting cables, attach the end with the Core Filter to the camcorder.
AUTOMATIC DEMONSTRATION
Automatic Demonstration takes place when “DEMO
MODE” is set to “ON” (factory-preset).
MENU/BRIGHT Wheel
Ⅲ Automatic Demonstration starts when there is no operation for
AUTO
about 3 minutes after the Power Switch is set to “
” or
MANUAL
“
” and no cassette is in the camcorder.
Ⅲ Performing any operation during the demonstration stops the
demonstration temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will resume.
Ⅲ “DEMO MODE” remains “ON” even if the camcorder power is
turned off.
Ⅲ To cancel Automatic Demonstration:
1. Set the Power Switch to “
Power Switch
Lock Button
MANUAL
” while pressing down the
Lock Button located on the switch and press the MENU/
BRIGHT wheel in. The Menu Screen appears.
Sub Menu
2. Rotate the MENU/BRIGHT wheel to select “
and press it. The SYSTEM Menu appears.
SYSTEM”
DEMO MODE
–
OFF
ON
3. Rotate the MENU/BRIGHT wheel to select “DEMO MODE”
and press it. The Sub Menu appears.
4. Rotate the MENU/BRIGHT wheel to select “OFF” and press it.
5. Rotate the MENU/BRIGHT wheel to select “
and press it twice. The normal screen appears.
RETURN”,
NOTE:
GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365
only
If you do not detach the Lens Cap, you cannot see the actual changes of the
Automatic Demonstration activated on the LCD monitor or viewfinder.
EN
7
GETTING STARTED
GETTING STARTED
CONTENTS
Power.................................................. 8 – 9
Grip Adjustment ......................................... 10
Viewfinder Adjustment.................................. 10
Shoulder Strap Attachment ............................. 10
Tripod Mounting.......................................... 10
Date/Time Settings...................................... 11
Loading/Unloading A Cassette ......................... 12
Recording Mode Setting ................................. 13
Loading A Memory Card (GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365 only) .................... 14
Picture Quality/Image Size Setting
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only) ............................................... 14
8
EN
GETTING STARTED (cont.)
BATT. RELEASE Button
Power
This camcorder’s 2-way power supply system lets
you choose the most appropriate source of power. Do
not use provided power supply units with other
equipment.
1
CHARGING THE BATTERY PACK
3
2
1
Tilt the viewfinder upward 1. With the arrow on
the battery pack pointing downward, push the battery
pack slightly against the battery pack mount 2, then
slide down the battery pack until it locks in place 3.
Power Switch
2
Set the Power Switch to “OFF”. Connect the AC
Adapter to the camcorder 4, then connect the Power
Cord to the AC Adapter 5.
CHARGE Lamp
3
Plug the Power Cord into an AC outlet 6.
The CHARGE lamp on the camcorder blinks to
indicate charging has started.
4
When the CHARGE lamp stops blinking but stays
lit, charging is finished. Unplug the Power Cord from
the AC outlet. Disconnect the AC Adapter from the
camcorder.
To Detach The Battery Pack . . .
..... Press BATT. RELEASE and pull out the battery
pack.
NOTES:
● If the protective cap is attached to the battery pack,
remove it first.
Battery pack
● During charging, the camcorder cannot be operated.
● Charging is not possible if the wrong type of battery is
used.
● When charging the battery pack for the first time or
after a long storage period, the CHARGE lamp may not
light. In this case, remove the battery pack from the
camcorder, then try charging again.
AC Adapter
● If the battery operation time remains extremely short
even after having been fully charged, the battery is
worn out and needs to be replaced. Please purchase a
new one.
● Using the optional AA-V40EG AC Power Adapter/
Charger, you can charge the BN-V408U/V416U/V428U
battery pack without the camcorder. However, it cannot
be used as an AC adapter.
4
connector
5
To DC
To AC outlet
6
Battery pack
BN-V408U
Charging time
approx. 1 hr. 30 min.
approx. 3 hrs.
BN-V416U (optional)
BN-V428U (optional)
approx. 5 hrs.
For other notes, ੬ pg. 68
EN
9
ATTENTION
USING THE BATTERY PACK
Before detaching the power source, make sure that
the camcorder’s power is turned off. Failure to do so
can result in a camcorder malfunction.
Perform step 1 of “CHARGING THE BATTERY
PACK” (੬ pg. 8).
Approximate recording time
<GR-DVL567/DVL367/DVL365/DVL167/DVL160>
NOTES:
● Recording time is reduced significantly under the
following conditions:
Battery pack LCD monitor on
Viewfinder on
• Zoom or Record-Standby mode is engaged
repeatedly.
BN-V408U
1 hr.
1 hr. 15 min.
(40 min.)
(35 min.)
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
BN-V416U
(optional)
2 hrs.
(1 hr. 10 min.)
2 hrs. 30 min.
(1 hr. 20 min.)
BN-V428U
(optional)
3 hrs. 30 min.
(2 hrs.)
4 hrs. 20 min.
(2 hrs. 20 min.)
BN-V840U
(optional)
5 hrs.
6 hrs. 10 min.
(2 hrs. 50 min.)
(3 hrs. 20 min.)
INFORMATION
BN-V856U
(optional)
7 hrs.
(4 hrs.)
8 hrs. 40 min.
(4 hrs. 40 min.)
The extended-use battery pack kit is a set composed
of a battery pack and AC Power Adapter/Charger:
VU-V840 KIT: BN-V840U battery pack & AA-V15EG
AC Power Adapter/Charger
(
) : when the video light is on
VU-V856 KIT: BN-V856U battery pack & AA-V80EG
AC Power Adapter/Charger
Read the kit's instruction manual before using.
Also, by using the optional JVC VC-VBN856U DC
Cord, it will be possible to connect BN-V840U or BN-
V856U battery packs to the camcorder and supply
power directly to the camcorder.
Approximate recording time
<GR-DVL867/DVL865/DVL767/DVL765>
Battery pack LCD monitor on Viewfinder on
BN-V408U
55 min.
(35 min.)
1 hr. 10 min.
(45 min.)
BN-V416U
(optional)
1 hr. 55min.
(1 hr. 15 min.)
2 hrs. 25 min.
(1 hr. 30 min.)
BN-V428U
(optional)
3 hrs. 25 min.
(2 hrs. 15 min.)
4 hrs. 20 min.
(2 hrs. 40 min.)
BN-V840U
(optional)
4 hrs. 25 min.
(2 hrs. 55 min.)
5 hrs. 40 min.
(3 hrs. 30 min.)
BN-V856U
(optional)
6 hrs. 40 min.
(4 hrs. 15 min.)
8 hrs. 30 min.
(5 hrs. 5 min.)
(
) : when the video light is on
USING AC POWER
Use the AC Adapter (connect as shown in the
illustration).
NOTES:
● The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
● For other notes, ੬ pg. 68.
To AC outlet
AC Adapter
To DC connector
10EN
GETTING STARTED (cont.)
Grip Adjustment
1
2 Separate the Velcro strip.
Pass your right hand through the loop and grasp
Power
Zoom Lever
the grip.
Recording
Start/Stop button
3
Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button and
Power Switch and Power Zoom Lever. Be sure to
fasten the Velcro strip to your preference.
Power Switch
Viewfinder Adjustment
AUTO
MANUAL
1
Set the Power Switch to “
” or “
”
Dioptre
Adjustment Control
while pressing down the Lock Button located on the
switch.
2
Turn the Dioptre Adjustment Control until the
indications in the viewfinder are clearly focused.
PAUSE
Shoulder Strap Attachment
1
Make sure the battery pack is removed. Following
the illustration, thread the strap through the eyelet 1,
then fold it back and thread it through the buckle 2.
Repeat the procedure to attach the other end of the
strap to the other eyelet 3 located under the Grip
Strap. Confirm the strap is not twisted.
2
1
3
Tripod Mounting
CAUTION
When attaching the camcorder to a tripod, extend its
legs to stabilise the camcorder. It is not advised to
use small sized tripods. This may cause damage to
the unit by falling over.
1
To attach the camcorder to a tripod, align the
direction stud and screw to the mounting socket and
stud hole on the camcorder. Then tighten the screw
clockwise. Some tripods are not equipped with studs.
EN 11
MENU/BRIGHT Wheel
Power Lamp
Date/Time Settings
The date/time is recorded onto the tape at all times,
but its display can be turned on or off during playback
(੬ pg. 50, 51).
MANUAL
” while pressing
down the Lock Button located on the switch. The
power lamp lights and the camcorder is turned on.
1
Set the Power Switch to “
2
Press the MENU/BRIGHT wheel in to access the
Menu Screen.
3
Rotate the MENU/BRIGHT wheel to select
DISPLAY”. Press it and the DISPLAY Menu
appears.
“
Power Switch
4
Rotate the MENU/BRIGHT wheel to select
“CLOCK ADJ.”. Press it and “day” is highlighted.
Rotate the MENU/BRIGHT wheel to input the day.
Press it. Repeat to input the month, year, hour and
minute.
Lock Button
Display
Rotate the MENU/BRIGHT wheel to select
W I P E / FADER
OF
F
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
MANUAL
SYSTEM
D I SPLAY
DSC
“
RETURN”, and press it twice. The Menu Screen
closes.
NOTE:
Even if you select “CLOCK ADJ.”, if the parameter is not
highlighted the camcorder’s internal clock continues to
operate. Once you move the highlight bar to the first date/
time parameter (day), the clock stops. When you finish
setting the minute and press the MENU/BRIGHT wheel
in, the date and time begin operation from the date and
time you just set.
END
GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365 only
DISPLAY Menu
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF
2 5 . 12 . 02
17 : 3 0
ADJ .
RETURN
CLOCK
ADJ .
2 5 . 12 . 02
17 : 3 0
12EN
GETTING STARTED (cont.)
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or
eject a cassette.
Erase protection tab*
Make sure the
window side is
facing out.
1
Slide and hold OPEN/EJECT in the direction of
the arrow then pull the cassette holder cover open
until it locks. The cassette holder opens automatically.
• Do not touch internal components.
Cassette holder
2
Insert or remove a tape and press “PUSH HERE”
to close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
• When the battery’s charge is low, you may not be
able to close the cassette holder cover. Do not apply
force. Replace the battery with a fully charged one
before continuing.
OPEN/EJECT
Switch
3
Close the cassette holder cover firmly until it
locks into place.
Cassette holder cover
PUSH HERE
Approximate recording time
* To Protect Valuable Recordings . . .
.... slide the erase protection tab on the back of the
tape in the direction of “SAVE”. This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading it.
Recording mode
Tape
SP
LP
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
45 min.
90 min.
120 min.
Be sure to press only the section labeled “PUSH
HERE” to close the cassette holder; touching other
parts may cause your finger to get caught in the
cassette holder, resulting in injury or product damage.
NOTES:
● It takes a few seconds for the cassette holder to open. Do not apply force.
● If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the
cassette holder still does not open, turn the camcorder off then on again.
● If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later,
insert it again.
● When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the
cassette holder cover.
● Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.
● Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed
with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or
unloading.
● When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a
previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not.
See page 20 for information about recording from the middle of a tape.
● Loosen the Grip Strap if it appears to interfere with the cassette holder cover operation (੬ pg. 10).
EN 13
MENU/BRIGHT Wheel
Power Lamp
Recording Mode Setting
Set the tape recording mode depending on your
preference.
MANUAL
” while pressing
down the Lock Button located on the switch. The
power lamp lights and the camcorder is turned on.
1
Set the Power Switch to “
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select
CAMERA” and press it. The CAMERA Menu
appears.
“
Power Switch
Lock Button
4
Rotate the MENU/BRIGHT wheel to select “REC
MODE” and press it. The Sub Menu appears. Select
“SP” or “LP” by rotating the MENU/BRIGHT wheel
and press it. Rotate the MENU/BRIGHT wheel to
select “
RETURN”, and press it twice. The Menu
Screen closes.
Display
• Audio Dubbing (੬ pg. 63) and Insert Editing
(੬ pg. 64) are possible on tapes recorded in the
SP mode.
• “LP” (Long Play) is more economical, providing
1.5 times the recording time.
Menu Screen
Sub Menu
REC MODE
–
SP
LP
NOTES:
● If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
● It is recommended that tapes recorded in the LP mode
on this camcorder be played back on this camcorder.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there may be
momentary pauses in the sound.
GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365
only
14EN
GETTING STARTED (cont.)
MENU/BRIGHT Wheel
Power Switch
Display
QUAL I TY
I MAGE S I ZE
REC SELECT
–
–
–
F I NE
1024X768
Lock Button
Card Cover
Label
Clipped edge
Power Lamp
RETURN
Memory card
Loading A Memory Card
Picture Quality/Image Size Setting
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only)
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only)
The Picture Quality/Image Size can be selected to
best match your needs. Refer to the chart on page 27
for your selection.
The provided memory card is already inserted in the
camcorder when you receive the camcorder.
1
2 Make sure the camcorder’s power is off.
Press PUSH OPEN and open the LCD monitor,
then set the Power Switch to “
1
Set the VIDEO/MEMORY Switch to “MEMORY”,
MANUAL
” while pressing
down the Lock Button located on the switch. The
power lamp lights and the camcorder turns on.
then open the card cover (MEMORY CARD).
3
Insert the memory card clipped edge first.
• Do not touch the terminal on the reverse side of the
label.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select
DSC” and press it. The DSC Menu appears.
4
To close the card cover, push it until you hear a
click.
“
4
Rotate the MENU/BRIGHT wheel to select
To Unload A Memory Card . . .
“QUALITY” and press it. The Sub Menu appears.
Rotate the MENU/BRIGHT wheel to select the
desired mode and press it.
..... in step 3 push the memory card, which then
comes out of the camcorder automatically. Pull it
out and close the card cover.
5
Rotate the MENU/BRIGHT wheel to select
NOTES:
“IMAGE SIZE” and press it. The Sub Menu appears.
Rotate the MENU/BRIGHT wheel to select the
desired mode and press it.
● Be sure to use only SD Memory Cards marked
“
“
” or MultiMediaCards marked
”.
● Some brands of memory cards are not compatible with
this camcorder. Before purchasing a memory card ,
consult its manufacturer or dealer.
6
Rotate the MENU/BRIGHT wheel to select
“
RETURN”, and press it twice. The Menu Screen
closes.
● Before using a new memory card, it is necessary to
FORMAT the card. ੬ pg. 36.
ATTENTION
Do not insert/remove the memory card while the
camcorder is turned on, as this may cause the
memory card to be corrupted or cause the camcorder
to become unable to recognize whether or not the
card is installed.
EN 15
TAPE RECORDING & PLAYBACK
TAPE RECORDING
&
PLAYBACK
CONTENTS
TAPE RECORDING ......................... 16 – 20
Basic Recording..................................... 16
Journalistic Shooting ............................... 17
Self-Recording ...................................... 17
Operation Mode .................................... 17
Zooming ............................................ 18
Video Light ......................................... 19
Time Code ........................................... 20
TAPE PLAYBACK ........................... 21 – 24
Normal Playback ................................... 21
Still Playback ....................................... 21
Shuttle Search ...................................... 21
Frame-By-Frame Playback ........................ 21
Connections .................................. 22 – 23
Blank Search ........................................ 24
16EN
TAPE RECORDING
Basic Recording
Power lamp
NOTE:
Power Switch
You should already have performed the procedures
listed below. If not, do so before continuing.
● Power (੬ pg. 8)
● Grip Adjustment (੬ pg. 10)
● Viewfinder Adjustment (੬ pg. 10)
● Load A Cassette (੬ pg. 12)
● Recording Mode Setting (੬ pg. 13)
1
Remove the lens cap.
During
shooting
GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only: Press PUSH OPEN, open the
LCD monitor and set the VIDEO/MEMORY Switch to
“VIDEO”.
Lock Button
Recording Start/Stop Button
AUTO
MANUAL
2
Set the Power Switch to “
” or “
”
Display
while pressing down the Lock Button located on the
switch.
25min
Tape remaining time
indicator (Approximate)
Shooting while using the LCD monitor: Make sure
the LCD monitor is fully open. Tilt it upward/
downward for best viewability.
Shooting while using the viewfinder: Close the
LCD monitor.
min
3 min
90 min
0 min
89 min
• The power lamp lights and the camcorder enters the
Record-Standby mode. “PAUSE” is displayed.
(Now calculating)
1 min
(Blinking)
2 min
(Blinking)
3
Press the Recording Start/Stop Button. “
appears while recording is in progress.
”
(Blinking)
To Stop Recording . . .
..... press the Recording Start/Stop Button. The
camcorder re-enters the Record-Standby mode.
BR I GHT
To Adjust The Brightness Of The Display . . .
..... rotate the MENU/BRIGHT wheel until the bright
level indicator on the display moves and the
appropriate brightness is reached.
MENU/BRIGHT Wheel
180°
90°
NOTES:
● If the Record-Standby mode continues for 5 minutes,
the camcorder’s power shuts off automatically. To turn
the camcorder on again, set the Power Switch to
AUTO
MANUAL
”.
“OFF”, then back to “
” or “
● The image will not appear simultaneously on the LCD
monitor and the viewfinder. It will appear in the
viewfinder when the LCD monitor is in the lock position,
and it will appear on the LCD monitor when fully
extended.
● When a blank portion is left between recorded scenes
on the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
“Recording from the middle of a tape” (੬ pg. 20).
● To turn the tally lamp or beep sounds off, ੬ pg. 46,
48.
VIDEO/MEMORY Switch
(GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/
DVL365 only)
PUSH OPEN Button
Tally lamp
(lights while
recording is in
progress)
For other notes, ੬ pg. 68
EN 17
JOURNALISTIC SHOOTING
In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder in
the desired position and tilt the LCD monitor in the
most convenient direction. It can rotate 270° (90°
downward, 180° upward).
Self-
Recording
SELF-RECORDING
You can shoot yourself while viewing your own image
in the LCD monitor. Open the LCD monitor and tilt it
upward 180° so that it faces forward, then point the
lens toward yourself and start recording.
To turn on the camcorder, set the Power Switch to
any operation mode except “OFF”while pressing
down the Lock Button located on the switch.
Operation Mode
Choose the appropriate operation mode according to
your preference using the Power Switch and VIDEO/
MEMORY Switch (GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365 only).
Power Switch
Power lamp
MANUAL
AUTO
Power Switch Position
Lock Button
OFF
PLAY
MANUAL
:
Allows you to set various recording functions using
the Menus. If you want more creative capabilities than
Full Auto recording, try this mode.
AUTO
(Full Auto):
Allows you to record using NO special effects or
manual adjustments. Suitable for standard recording.
OFF:
Allows you to switch off the camcorder.
PLAY:
VIDEO/MEMORY Switch
• Allows you to play back a recording on the tape.
• Allows you to transfer a still image recorded on the
tape to a computer (GR-DVL167/DVL160 only).
• Allows you to access data stored on the memory
card or to transfer a still image stored on the
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only; open the
LCD monitor to access this switch.)
memory card to a computer (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/DVL367/DVL365 only).
VIDEO/MEMORY Switch Position
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only)
When the Power Switch is set to “ AUTO ”, “ ” appears.
MANUAL
When set to “
” or “PLAY”, there is no indication.
VIDEO:
• Allows you to record on a tape or play back a tape.
If “REC SELECT” is set to “
/
” in the
DSC Menu Screen, still images are recorded on the
memory card as well.
• Zoom magnification over 10X is available
(੬ pg. 18, 47).
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only)
1024
MEMORY:
Allows you to record on a memory card or access
data stored on a memory card.
When the Power Switch is set to “ AUTO ” or “
” and
MANUAL
the VIDEO/MEMORY Switch is set to “MEMORY”, the
currently selected image size appears.When set to
“VIDEO”, there is no indication.
18EN
TAPE RECORDING (cont.)
Zoom in (T:Telephoto)
FEATURE: Zooming
1x
W
T
PURPOSE:
To produce the zoom in/out effect, or an instanta-
neous change in image magnification.
10x
W
T
20x
W
T
40x
W
T
OPERATION:
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Zoom out (W:Wide angle)
Slide the Power Zoom Lever towards “W”.
Ⅲ The further you slide the Power Zoom Lever, the
quicker the zoom action.
Zoom display
NOTES:
10x
W
T
● Focusing may become unstable during Zooming. In
this case, set the zoom while in Record-Standby,
lock the focus by using the manual focus
(੬ pg. 43), then zoom in or out in Record mode.
● Zooming is possible to a maximum of 500X, or it
can be switched to 10X magnification using the
optical zoom (੬ pg. 47).
Digital zoom zone
10X (optical) zoom
zone
● Zoom magnification of over 10X is done through
Digital image processing, and is therefore called
Digital Zoom.
Approximate zoom ratio
● During Digital zoom, the quality of image may
suffer.
Power Zoom Lever
● Digital zoom cannot be used when the VIDEO/
MEMORY Switch is set to “MEMORY” (੬ pg. 17).
● Macro shooting (as close as approx. 5 cm to the
subject) is possible when the Power Zoom Lever is
set all the way to “W”. Also see “TELE MACRO” in
the Menu Screen on page 48.
EN 19
FEATURE: Video Light
PURPOSE:
To brighten the scene when natural lighting is too
dim.
OPERATION:
Set LIGHT OFF/AUTO/ON as required:
OFF : Turns off the light.
AUTO : Automatically turns on the light when the
camcorder senses insufficient lighting on
the subject.
LIGHT OFF/AUTO/ON Switch
(Open the LCD monitor to
access this switch.)
ON
: Always keeps the light on as long as the
camcorder is turned on.
Ⅲ The video light can only be used with the
camcorder’s power on.
Ⅲ It is recommended to set the white balance
DANGER
Ⅲ The video light can become extremely
hot. Do not touch it either while in
operation or soon after turning it off,
otherwise serious injury may result.
(੬ pg. 45) to
when you use the video light.
Ⅲ When not using the video light, turn it off to save
battery power.
NOTES:
● Even if the battery indicator (
) does not blink
due to low battery charge, the camcorder may turn
off automatically when you turn on the video light, or
when you start recording with the video light turned
on.
● When LIGHT OFF/AUTO/ON is set to “AUTO”:
• Depending on the lighting conditions, the video
light may keep turning on and off. In this case,
manually switch the light on or off using LIGHT
OFF/AUTO/ON.
• While the “SHUTTER” or “SPORTS” mode
(੬ pg. 39) is engaged, the light is likely to stay
on.
• While the “TWILIGHT” mode (੬ pg. 39) is
engaged, the light will not activate.
Ⅲ Do not place the camcorder into the carrying case
immediately after using the video light, since it remains
extremely hot for some time.
Ⅲ When operating, keep a distance of about 30 cm
between the video light and people or objects.
Ⅲ Do not use near flammable or explosive materials.
Ⅲ Do not place the camcorder in a cabinet or box while
the video light is in operation.
Ⅲ When using the video light, if you wish to install the
camcorder in a fixed position, attach it to a tripod, etc.
Do not affix it directly to a surface such as a table top.
Ⅲ It is recommended that you consult your nearest JVC
dealer for replacing the video light.
• While the “Night-Scope” mode (੬ pg. 38) is
engaged, the light will not activate.
20EN
TAPE RECORDING (cont.)
Time Code
During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code begins counting from “00:00:00”
(minute:second:frame). If recording starts from the end of a previously recorded scene, the time code
continues from the last time code number.
To perform Random Assemble Editing (੬ pg. 58 – 62), time code is necessary. If during recording a blank
portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time
code starts counting up again from “00:00:00”. This means the camcorder may record the same time codes
as those existing in a previously recorded scene. To prevent this, perform “Recording From The Middle of A
Tape” below in the following cases;
• When shooting again after playing back a
recorded tape.
• When power shuts off during shooting.
• When a tape is removed and re-inserted during
shooting.
Display
Frames are not displayed
during recording.
Minutes
• When shooting using a partially recorded tape.
• When shooting on a blank portion located
partway through the tape.
• When shooting again after shooting a scene
then opening/closing the cassette holder cover.
Seconds
Frames
(25 frames = 1 second)
12 : 34 : 24
Recording From The Middle Of A Tape
1. Play back a tape or use Blank Search (੬ pg. 24) to find the spot at which you want to start recording,
then engage the Still Playback mode (੬ pg. 21).
AUTO
MANUAL
” while pressing down the Lock Button located on the switch,
2. Set the Power Switch to “
then start recording.
” or “
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time code indication does not move smoothly.
● The time code is displayed only when “TIME CODE” is set to “ON” (੬ pg. 49, 50).
When a blank portion is recorded on a tape
Time code
00:00:00
Time code
05:43:21
Time code
00:00:00
Tape
Already recorded scene
Blank
Newly recorded scene
Shooting start point
Shooting stop point
Shooting start point
Proper recording
Time code
00:00:00
Time code
05:43:21
Time code
05:44:00
Tape
Already recorded scene
New scene
Latest scene
Shooting start point
Shooting start point
Shooting start point
EN 21
TAPE PLAYBACK
Stop Button (5)
Normal Playback
Rewind Button (2
)
1
2 Load a tape (੬ pg. 12).
Set the VIDEO/MEMORY Switch to “VIDEO”
Play/Pause Button (4/6)
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only), then set the Power Switch to
“PLAY” while pressing down the Lock Button located on
the switch.To start playback, press 4/6.
Fast-Forward Button (3
)
Power Zoom Lever (VOL.)
• To stop playback, press 5.
• Press
2
to rewind, or
3
to fast-forward the tape
VIDEO/MEMORY Switch
(GR-DVL867/DVL865/
DVL767/DVL765/
DVL567/DVL367/DVL365
only; open the LCD
monitor to access this
switch.)
during Stop mode.
To Control The Speaker Volume . . .
..... slide the Power Zoom Lever (VOL.) towards “+”
to turn up the volume, or towards “–” to turn down
the volume.
Speaker
NOTES:
● If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To
turn on again, set the Power Switch to “OFF”, then to “PLAY”.
● The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV (੬ pg. 22).
● You can also view the playback picture on the LCD monitor with it flipped over and pushed against the camera body.
● LCD monitor/viewfinder indications:
• When power is supplied from a battery: the “
When power is supplied from an AC outlet: “
” battery pack remaining power indicator is displayed.
” does not appear.
• During Stop mode, none of the indications are displayed.
● When a cable is connected to the AV connector, the sound is not heard from the speaker.
Still Playback: Pauses during playback.
1) Press 4/6 during playback.
2) To resume normal playback, press 4/6 again.
● If still playback continues for more than about 3 minutes, the camcorder’s Stop mode is automatically engaged.
After 5 minutes in the Stop mode, the camcorder’s power is automatically turned off.
● When 4/6 is pressed, the image may not pause immediately while the camcorder stabiliseds the still image.
Shuttle Search: Allows high-speed search in either direction.
1) Press
2) To resume normal playback, press 4/6.
● During playback, press and hold or 3. The search continues as long as you hold the button. Once you
release it, normal playback resumes.
3
for forward or
2
for reverse search during playback.
2
● A slight mosaic effect appears on screen during Shuttle Search. This is not a malfunction.
Frame-By-Frame Playback: Allows frame-by-frame search.
1) Engage Still Playback.
2) Rotate the MENU/BRIGHT wheel towards “+” for forward Frame-By-Frame Playback, or towards “–” for reverse
Frame-By-Frame Playback during Still Playback.
● To resume normal playback, press 4/6.
● You can also use the provided remote control for Frame-By-Frame Playback (੬ pg. 56).
Slow-Motion Playback/Playback Special Effects and Playback Zoom
Available only with the remote control (provided) (੬ pg. 56, 57).
ATTENTION
During Shuttle Search, parts of the picture may not be clearly visible, particularly on
the left side of the screen.
22EN
Connections
TAPE PLAYBACK (cont.)
Use the provided Audio/Video cable and optional S-Video cable.
To TV or VCR
To AV
When the S-Video
cable is not used.
Audio/Video cable
[mini-plug to RCA
plug] (provided)
Yellow to
VIDEO IN
TV
Connector cover*
White to
AUDIO L IN**
Red to
AUDIO R IN**
To S-VIDEO
VCR
S-Video cable
(optional)
To S-VIDEO IN
* When connecting the cables, open this cover.
** The Audio cable is not required for watching still images only.
If your TV/VCR has a 21-pin connector
Use the provided Cable Adapter.
When the S-Video
cable is not used.
Cable
Adapter
Yellow
Audio/Video cable
[mini-plug to RCA plug] (provided)
White to
AUDIO L*
Red to
AUDIO R*
TV or VCR
To AV
Camcorder
S-Video cable
(optional)
To S-VIDEO
To
-IN
“Y/C”/“CVBS”
Video Out
Select Switch
* The Audio cable is not required for watching still images only.
NOTE:
Set the video out select switch of the cable adapter as required:
Y/C
: When connecting to a TV or VCR which accepts Y/C signals and uses an S-Video cable.
CVBS : When connecting to a TV or VCR which does not accept Y/C signals and uses an audio/video cable.
EN 23
NOTES:
1
2 Make sure all units are turned off.
in the illustration (੬ pg. 22).
If using a VCR . . . go to step 3.
If not . . . go to step 4.
Connect the camcorder to a TV or VCR as shown
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● To monitor the picture and sound from the camcorder
without inserting a tape or memory card*, set the
AUTO
MANUAL
camcorder’s Power Switch to “
” or “
”,
then set your TV to the appropriate input mode.
* GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only
3
Connect the VCR output to the TV input, referring
to your VCR’s instruction manual.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound when
the camcorder is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the TV
as interference will occur in the camcorder playback
picture.
4
5 Turn on the camcorder, the VCR and the TV.
Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
To choose whether or not the following displays
appear on the connected TV . . .
• Date/Time
● While the Audio/Video cable is connected to the AV
connector, sound cannot be heard from the speaker.
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in the
Menu Screen (੬ pg. 50).
Or, press DISPLAY on the remote control
(provided) to turn on/off the date indication.
• Time Code
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 50).
• Playback Sound Mode, Tape Speed And Tape
Running Displays for tape playback
..... set “ON SCREEN” to “LCD” or “LCD/TV” in the
Menu Screen (੬ pg. 50).
24EN
TAPE PLAYBACK (cont.)
BLANK Button
Blank Search
Helps you find where you should start recording in
the middle of a tape to avoid time code interruption
(੬ pg. 20).
1
2 Load a tape (੬ pg. 12).
Set the VIDEO/MEMORY Switch to “VIDEO”
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only), then set the Power Switch to
“PLAY” while pressing down the Lock Button located
on the switch.
Power Switch
Lock Button
3
Press BLANK.
• “BLANK SEARCH” appears blinking and the
camcorder automatically starts reverse or forward
shuttle search, then stops at the spot which is about
3 seconds of tape before the beginning of the
detected blank portion.
Display
44
To cancel Blank Search midway . . .
..... press 5.
BLANK SEARCH
NOTES:
● In step 3, if the current position is at a blank portion the
camcorder searches in the reverse direction, and if the
current position is at a recorded portion the camcorder
searches in the forward direction.
● Blank Search does not work if “HEAD CLEANING
REQUIRED. USE CLEANING CASSETTE” has
appeared with the tape.
● If the beginning or end of the tape is reached during
Blank Search, the camcorder stops automatically.
● A blank portion which is shorter than 5 seconds of tape
may not be detected.
VIDEO/MEMORY Switch (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/DVL367/DVL365 only;
open the LCD monitor to access this switch.)
● The detected blank portion may be located between
recorded scenes. Before you start recording, make sure
there is no recorded scene after the blank portion.
Stop Button (5)
EN 25
MEMORY CARD RECORDING & PLAYBACK
MEMORY CARD
RECORDING
&
PLAYBACK
Memory Card recording features are
available on GR-DVL867,GR-DVL865,
GR-DVL767, GR-DVL765, GR-DVL567,
GR-DVL367 and GR-DVL365.
CONTENTS
MEMORY CARD RECORDING .........26 – 27
Basic Shooting (Snapshot) ............... 26 – 27
MEMORY CARD PLAYBACK ...........28 – 29
Normal Playback .................................. 28
Auto Playback ..................................... 28
Index Playback .................................... 29
Viewing File Information ......................... 29
Removing On-Screen Display .................... 29
ADVANCED FEATURES ....................30 – 36
Protecting Files .................................... 30
Deleting Files ...................................... 31
Dubbing Still Images Recorded On A Tape To A
Memory Card ....................................... 32
E-Mail Clip Recording ............................. 33
Setting Print Information
(DPOF Setting)............................. 34 – 35
Making A New Folder ............................ 36
Initialising A Memory Card ...................... 36
26EN
MEMORY CARD RECORDING
SNAPSHOT Button
Basic Shooting (Snapshot)
You can use your camcorder as a digital still camera
for taking snapshots.
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 8)
● Grip Adjustment (੬ pg. 10)
● Viewfinder Adjustment (੬ pg. 10)
● Loading A Memory Card (੬ pg. 14)
● Picture Quality/Image Size Setting (੬ pg. 14)
Power Switch
1
Set the VIDEO/MEMORY Switch to “MEMORY”,
AUTO
MANUAL
then set the Power Switch to “
” or “
”
Lock Button
while pressing down the Lock Button located on the
switch.
VIDEO/MEMORY Switch (Open the
LCD monitor to access this switch.)
2
Press SNAPSHOT. “PHOTO” appears while the
snapshot is being taken.
The image is recorded on the memory card.
• Still images are recorded in the snapshot mode with
no frame.
Image Size
Displays the image file size: 1280 (1280 x 960)*, 1024 (1024 x 768) or 640 (640 x 480)
(੬ pg. 14).
* GR-DVL867/DVL865/DVL767/DVL765 only.
Shooting icon
Appears and blinks during shooting.
Card icon
Appears during shooting and blinks when a memory card is not loaded:
(SD Memory Card) or
(MultiMediaCard).
1024
15
Remaining number of shots
Displays the remaining number of shots that can be stored.
The number increases or decreases depending on the Picture Quality/Image Size, etc.
Picture Quality
Displays the quality of image: F (Fine) or S (Standard) (in order of quality) (੬ pg. 14).
Display
EN 27
To Delete Unwanted Still Images . . .
FULL
..... when unwanted still images are stored in the
memory card or its memory is full, refer to “Deleting
Files” (੬ pg. 31) and delete unwanted still images.
Snapshot mode with no
frame
To Remove The Shutter Sound . . .
..... when you do not want to hear the shutter sound,
set “BEEP” to “OFF” in the Menu Screen
(੬ pg. 46, 48). The sound is no longer heard
from the speaker.
There is the sound of a shutter closing.
NOTES:
● Even if “DIS” is set to “ON” (੬ pg. 47), the Stabilisedr
will be disabled.
● If Snapshot recording is not possible, “PHOTO” blinks
To Protect Valuable Files (available only for SD
Memory Card) . . .
when SNAPSHOT is pressed.
● If Programme AE with special effects (੬ pg. 38) is
engaged, certain modes of Programme AE with special
effects are disabled during Snapshot recording. In such
a case, the icon blinks.
Write/erase protection tab
● If shooting is not performed for approx. 5 minutes when
AUTO
MANUAL
the Power Switch is set to “
” or “
” and
. . . slide the write/erase protection tab on the side
of the memory card in the direction of
power is supplied from the battery pack, the camcorder
shuts off automatically to save power. To perform
shooting again, set the Power Switch to “OFF”, then to
“LOCK”. This prevents the memory card from
being recorded over. To record on this
memory card, slide the tab back to the
AUTO
MANUAL
“
” or “
”.
● The Motor Drive mode (੬ pg. 42) is disabled when the
VIDEO/MEMORY Switch is set to “MEMORY”.
● Still images taken are compliant to DCF (Design rule for
Camera File system). They do not have any
compatibility with devices which are not compliant to
DCF.
position opposite to “LOCK” before loading it.
Approximate Number of Storable Images <GR-DVL567/DVL367/DVL365>
SD Memory Card
MultiMediaCard
Image Size/Picture
Quality
8MB
20
16MB
45
32MB
95
64MB
190
8MB
24
16MB
48
32MB
100
1024 x 768/FINE
1024 x 768/
STANDARD
320
215
645
65
45
145
95
310
205
605
405
75
55
160
105
640 x 480/FINE
640 x 480/
STANDARD
160
295
625
1215
190
320
Approximate Number of Storable Images <GR-DVL867/DVL865/DVL767/DVL765>
SD Memory Card
MultiMediaCard
Image Size/Picture
Quality
8MB
12
16MB
28
32MB
62
64MB
120
8MB
16
16MB
32
32MB
64
1280 x 960/FINE
1280 x 960/
STANDARD
44
20
98
46
205
98
405
190
50
25
100
50
200
100
1024 x 768/FINE
1024 x 768/
STANDARD
320
210
640
66
46
145
98
310
205
605
405
80
50
160
105
640 x 480/FINE
640 x 480/
STANDARD
150
295
625
1215
160
320
NOTE:
The number of storable images depends on the selected picture quality as well as the composition of the subjects in the
images and the type of memory card being used.
28EN
MEMORY CARD PLAYBACK
Normal Playback
Rewind Button (2
)
Play/Pause Button
4/6)
(
1
2 Load a memory card (੬ pg. 14).
then set the Power Switch to “PLAY” while pressing
down the Lock Button.
Set the VIDEO/MEMORY Switch to “MEMORY”,
Stop Button (5)
Fast-Forward Button
(
3
)
• The type of file played back last time is played.
If you want to select another type of file, go to
step 3. If not, go to step 4.
3
Press SELECT. The MEMORY SELECT Screen
appears. Rotate the MENU/BRIGHT wheel to select
the type of file: IMAGE or E-MAIL CLIP (੬ pg. 33).
Then press the MENU/BRIGHT wheel in. The
selected type of file is displayed.
SELECT Button
4
If you are viewing an IMAGE file . . .
Press to display the next image, or press
display the previous image.
MANUAL
AUTO
3
2
to
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
OFF
If you are viewing an E-MAIL CLIP file . . .
PLAY
Press 4/6 to play back the displayed video clip. To
stop video clip playback, press 5.
Lock Button
Power Switch
NOTES:
● Pressing INFO gives you details on the displayed
file (੬ pg. 29, “Viewing File Information”).
● You can also overview several files at a time
(੬ pg. 29, Index Playback).
● You can turn off the on-screen playback display
(੬ pg. 29, “Removing On-Screen Display”).
[For Normal Playback: IMAGE]
To display the
next image
To display the
previous image
Auto Playback
You can run through all the images stored on memory
automatically.
1
2 Perform steps 1 and 2 above.
Press 4/6.
• If you press
2
during Auto Playback, images are
displayed in descending order.
• If you press during Auto Playback, images are
displayed in ascending order.
3
3
To end Auto Playback, press 5.
Display
NOTES:
● Even if you shoot a new image after playing back a low-
numbered one, this will not overwrite an existing image,
because new images are automatically stored after the
last-recorded one.
[For Auto Playback: IMAGE]
● Images shot in a file size that is not compatible with this
camcorder will be displayed as reduced-size thumbnail
images. These thumbnail images cannot be transferred
to a PC.
Normal Playback:
E-MAIL CLIP
E-MAIL CLIP
● Images shot with devices (such as JVC GR-DVX7) that
are not compatible with DCF cannot be viewed with this
camcorder; “UNSUPPORTED FILES” will be displayed.
EN 29
MENU/BRIGHT Wheel
INFO Button
Index Playback
INDEX Button
You can view several different files stored on the
memory card at a time. This browsing capability
makes it easy to locate a particular file you want.
1
2 Perform steps 1 through 3 of “Normal Playback”.
3 Press INDEX. The Index Screen appears.
Rotate the MENU/BRIGHT wheel to move the
frame to the desired file.
• Pressing
3
displays the next page and
2
displays the previous page.
• Pressing INFO gives you details on the currently
selected file (੬ “Viewing File Information”).
SELECT Button
Selected image
Index number
4
Press the MENU/BRIGHT wheel in. The selected
file is displayed.
• Pressing INFO gives you details on the displayed
file (੬ “Viewing File Information”).
Index Screen
1
4
7
2
5
8
3
6
9
Viewing File Information
You can get the relevant file information by pressing
the INFO button during normal playback or Index
playback.
DCF
:Folder and file number
(IMAGE files only)
FOLDER :Folder name (੬ pg. 36)
Info Screen
FILE
DATE
SIZE
:File name (੬ pg. 36)
:Date the file was made
:Image size (੬ pg. 14)
DCF
: 1 0 0 - 0 0 1 0
: 1 0 0 JVCGR
: DVC0 0 0 1 0
: 2 7 . 3 . 0 2
FOLDER
F I LE
DATE
S I ZE
QUALITY :Picture quality
(IMAGE files only ੬ pg. 14)
:Playback time
: 1 0 2 4X7 6 8
QUAL I TY : F I NE
PROTECT : OFF
TIME
(E-MAIL CLIP files only ੬ pg. 33)
PROTECT :When set to ON, the file is protected
from accidental erasure (੬ pg. 30).
Operation mode indicator
• Press INFO again to close the Info Screen.
Battery indicator
Playback Screen
NOTE:
With images shot with another device or processed on a
PC, “QUALITY: – – –” will be displayed.
Removing On-Screen Display
1
Perform steps 1 and 2 of “Normal Playback”
(੬ pg. 28).
2
Make sure an IMAGE file is displayed
(੬ pg. 28); if not, press SELECT to access the
MEMORY SELECT Screen. Rotate the MENU/
BRIGHT wheel to select “IMAGE” and press it.
Menu Screen
MENU
3
Press the MENU/BRIGHT wheel in. The Menu
Screen appears. Rotate the MENU/BRIGHT wheel to
select “DISPLAY”, then press it.
D I SPLAY OFF
ON
4 Rotate the MENU/BRIGHT wheel to select “OFF”,
then press it. The operation mode indicator and
battery indicator ( ) disappear.
• To display the indicators again, select “ON” in step
4.
30EN
ADVANCED FEATURES
MENU/BRIGHT Wheel
Protecting Files
The Protect mode helps prevent the accidental
erasure of files.
1
2 Load a memory card (੬ pg. 14).
Set the VIDEO/MEMORY Switch to “MEMORY”,
then set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
• A stored file is displayed.
If you want to select another type of file, go to
step 3. If not, go to step 4.
Power Switch
Lock Button
3
Press SELECT. The MEMORY SELECT Screen
appears. Rotate the MENU/BRIGHT wheel to select
the type of file: IMAGE or E-MAIL CLIP (੬ pg. 33).
Then press the MENU/BRIGHT wheel in. The
selected type of file is displayed.
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
4
Press the MENU/BRIGHT wheel in. The Menu
Screen appears. Rotate the MENU/BRIGHT wheel to
select “PROTECT”, then press it.
5
Rotate the MENU/BRIGHT wheel to select the
desired mode.
CURRENT : Protects the currently displayed file.
PROT.ALL : Protects all files stored on the memory
card.
6
Press the MENU/BRIGHT wheel in. The
PROTECT Screen appears.
SELECT Button
Menu Screen
• If you selected “CURRENT” in step 5, press
2
or
3
to select the desired file.
Display
7
Rotate the MENU/BRIGHT wheel to select
MENU
“EXECUTE” and press it.
PROTECT
• To cancel protection, select “RETURN”.
DELETE
DPOF
NOTES:
NO . RESET
FORMAT
D I SPLAY
● If the “
” mark appears, the currently displayed file is
protected.
● When the memory is initialised or corrupted, even
protected files are deleted. If you do not want to lose
important files, transfer them to a PC and save them.
END
MENU
TO REMOVE PROTECTION
Before doing the following, perform steps 1 through 4
PROTECT
CURRENT
PROT . ALL
CANC . ALL
above.
RETURN
5
Rotate the MENU/BRIGHT wheel to select the
desired mode.
CURRENT : Removes protection from the currently
displayed file.
PROTECT Screen
CANC.ALL : Removes protection from all files stored
on the memory card.
PROTECT
6
Press the MENU/BRIGHT wheel in. The
PROTECT Screen appears.
• If you selected “CURRENT”, press
select the desired file.
PROTECTED
RETURN
2
or
3
to
7Rotate the MENU/BRIGHT wheel to select
“EXECUTE” and press it.
• To cancel selection, select “RETURN”.
EN 31
MENU/BRIGHT Wheel
Deleting Files
Previously stored files can be deleted either one at a
time or all at once.
1
2 Load a memory card (੬ pg. 14).
Set the VIDEO/MEMORY Switch to “MEMORY”,
then set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
• A stored file is displayed.
If you want to select another type of file, go to
step 3. If not, go to step 4.
Power Switch
Lock Button
3
Press SELECT. The MEMORY SELECT Screen
appears. Rotate the MENU/BRIGHT wheel to select
the type of file: IMAGE or E-MAIL CLIP (੬ pg. 33).
Then press the MENU/BRIGHT wheel in. The
selected type of file is displayed.
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
4
Press the MENU/BRIGHT wheel in. The Menu
Screen appears. Rotate the MENU/BRIGHT wheel to
select “DELETE”, then press it.
5
Rotate the MENU/BRIGHT wheel to select the
desired mode.
CURRENT : Deletes the currently displayed file.
ALL
: Deletes all files stored on the memory
card.
6
Press the MENU/BRIGHT wheel in. The DELETE
SELECT Button
Menu Screen
Screen appears.
• If you selected “CURRENT” in step 5, press
2
or
Display
3
to select the desired file.
7
Rotate the MENU/BRIGHT wheel to select
MENU
“EXECUTE” and press it.
DELETE
CURRENT
ALL
• If the “
” mark appears, the selected file is
protected and cannot be deleted
(੬ pg. 30).
• To cancel deletion, select “RETURN”.
RETURN
NOTES:
● Protected files (੬ pg. 30) cannot be deleted with the
above operation. To delete them, remove protection
first.
DELETE Screen
DELETE
● Once files are deleted, they cannot be restored. Check
files before deleting.
DELETE?
EXECUTE
RETURN
CAUTION
Do not remove the memory card or perform any other
operation (such as turning off the camcorder) during
deletion. Also, be sure to use the provided AC
Adapter, as the memory card may be corrupted if the
battery becomes exhausted during deletion. If the
memory card becomes corrupted, initialise it.
(੬ pg. 36)
32EN
ADVANCED FEATURES (cont.)
SNAPSHOT Button
Dubbing Still Images Recorded On A Tape
To A Memory Card
Still images can be dubbed from a tape to a memory
card.
1
Load a memory card (੬ pg. 14) and cassette
(੬ pg. 12).
2
Set the VIDEO/MEMORY Switch to “VIDEO”,
then set the Power Switch to “PLAY” while pressing
down the Lock Button.
3
Press the MENU/BRIGHT wheel in. The Menu
Power Switch
Lock Button
Display
Screen appears. Rotate it to select “
VIDEO” and
press it. The VIDEO Menu appears.
4
Rotate the MENU/BRIGHT wheel to select
COPY” and press it. The Sub Menu
“
appears. Rotate it to select “ON” and press it.
Selection is complete.
Menu Screen
5
Rotate the MENU/BRIGHT wheel to select “
RETURN” and press it twice. The normal playback
screen reappears.
COPY
–
OFF
ON
6
To select a video image to be dubbed, start
playback by pressing 4/6. At the moment you find
the image you wish to dub, press it again to engage
Still Playback.
6
SP
7
To start dubbing, press SNAPSHOT. The selected
image is stored on the memory card.
• “ ” blinks during dubbing.
NOTES:
● If SNAPSHOT is pressed in step 7 when a memory
card is not loaded, the message “COPYING FAILED” is
displayed.
● If an image recorded on the tape using the WIDE mode
(੬ pg. 48) is dubbed to a memory card, the WIDE
mode identifying signal is not dubbed with it.
● To use Playback Special Effects with a video image you
wish to dub, perform up to step 7 using the remote
control (provided) (੬ pg. 56).
Play/Pause Button (4/6)
Stop Button (5)
MENU/BRIGHT Wheel
● Images are dubbed in 640 x 480 pixels.
E-MAIL Button
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
EN 33
Display
E-Mail Clip Recording
160
E-
MAIL CLIP
35mi n
00 : 00
STANDBY
Remaining time
You can make video clips from real-time camera
image or recorded video footage and store them in a
memory card as files which can be conveniently sent
via e-mail.
TO MAKE VIDEO CLIPS FROM REAL-TIME
CAMERA IMAGE
Shooting starts when the
Recording Start/Stop
Button is pressed
1
Load a memory card (੬ pg. 14). Set the VIDEO/
160
E-MAIL CLIP
35mi n
00 : 15
REC
MEMORY Switch to “MEMORY”, then set the Power
e
AUTO
MANUAL
” while pressing down
Switch to “
” or “
the Lock button located on the switch.
2
Press E-MAIL. The camcorder enters the E-Mail
Clip Record-Standby mode.
3
Press the Recording Start/Stop Button to start
shooting.
Shooting stops when the
Recording Start/Stop
Button is pressed again
4
Press the Recording Start/Stop Button to stop
shooting. “COMPLETED” is displayed, then the
camcorder re-enters the E-Mail Clip Record-Standby
mode.
COMPLETED
5
Press E-MAIL to end E-Mail Clip Recording. The
normal screen reappears.
Recording is complete
To view video clips stored on a memory card . . .
..... ੬ pg. 28, 29.
TO MAKE VIDEO CLIPS FROM RECORDED
VIDEO FOOTAGE
1
Load a memory card (੬ pg. 14) and cassette
(੬ pg. 12). Set the VIDEO/MEMORY Switch to
“VIDEO”, then set the Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch.
NOTES:
● Video clips are stored in 160 x 120-pixel format.
● Playback operation cannot be performed during E-Mail
Clip Recording.
● If the end of the tape is reached in step 3, the E-Mail
Clip Record-Standby mode will be automatically
cancelled.
● The video clip files made with this camcorder are
MPEG4 compliant, however, some MPEG4 files made
with other devices may not be played back with this
camcorder.
● You can delete unwanted video clips (੬ pg. 31,
“Deleting Files”) or protect important ones from
accidental erasure (੬ pg. 30, “Protecting Files”).
● Video noise may appear while viewing video clips in the
LCD monitor or viewfinder, however, this noise is not
present in the actual video clips stored on the memory
card.
● You can also view video clips on your PC by using
Windows® Media Player. Refer to the instructions of the
PC and software.
2
4/6 to start tape playback.
3 Press
Press E-MAIL. “E-MAIL CLIP STANDBY”
appears and the camcorder enters the E-Mail Clip
Record-Standby mode.
4
Press the Recording Start/Stop Button to start E-
Mail Clip Recording.
5
Press the Recording Start/Stop Button to stop E-
Mail Clip Recording. “COMPLETED” is displayed,
then the camcorder re-enters the E-Mail Clip Record-
Standby mode.
6
Press E-MAIL to end E-Mail Clip Recording. The
normal screen reappears.
To cancel E-Mail Clip Recording . . .
..... after step 3, press E-MAIL again or press 5 to
stop tape playback.
To view video clips stored on a memory card . . .
..... ੬ pg. 28, 29.
34EN
ADVANCED FEATURES (cont.)
MENU/BRIGHT Wheel
Setting Print Information (DPOF Setting)
This camcorder is compatible with the DPOF (Digital
Print Order Format) standard in order to support
future systems such as automatic printing, which
records information about the still images you wish to
print (such as the number of prints to make). There
are 2 print information settings available: “To print all
still images (one print for each)” explained below and
“To print by selecting still images and no. of prints”
(੬ pg. 35).
TO PRINT ALL STILL IMAGES
(ONE PRINT FOR EACH)
Power Switch
Lock Button
1
Set the VIDEO/MEMORY switch to “MEMORY”,
then set the Power Switch to “PLAY”, while pressing
down the Lock Button located on the switch.
• A stored file is displayed.
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
2
Make sure an IMAGE file is displayed
(੬ pg. 28); if not, press SELECT to access the
MEMORY SELECT Screen. Rotate the MENU/
BRIGHT wheel to select “IMAGE” and press it.
3
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
4
Rotate the MENU/BRIGHT wheel to select
“DPOF” and press it. The Sub Menu appears.
5
Rotate the MENU/BRIGHT wheel to select “ALL
1” and press it. Selection is complete. The DPOF
Screen appears.
SELECT Button
Menu Screen
Display
6
Rotate the MENU/BRIGHT wheel to select
“EXECUTE” and press it. The normal playback
screen appears.
MENU
• To cancel selection, rotate the MENU/BRIGHT
wheel to select “RETURN” and press it.
DPOF
CURRENT
ALL
RESET
RETURN
1
To Reset The Setting . . .
..... select “RESET” in step 5. The setting is reset to 0
for all still images.
DPOF Screen
DPOF
ALL1?
EXECUTE
RETURN
EN 35
Fast-Forward (3) Button
TO PRINT BY SELECTING STILL IMAGES AND
NO. OF PRINTS
MENU/
Rewind Button (2
)
BRIGHT Wheel
1
2 Perform steps 1 through 4 on pg. 34.
Rotate the MENU/BRIGHT wheel to select
“CURRENT” and press it. Selection is complete. The
DPOF Screen appears.
3
Press
print appears.
2
or
3
so that the image you wish to
4
Rotate the MENU/BRIGHT wheel to move the
highlight bar to the SHEETS number indication and
press it.
SELECT Button
5
Select the number of prints by rotating the MENU/
BRIGHT wheel and press it.
Repeat steps 3 through 5 for the desired number of
VIDEO/MEMORY Switch (Open the
LCD monitor to access this switch.)
prints.
• The number of prints can be set up to 15.
• To correct the number of prints, select the image
again and change the number.
Display
6
Rotate the MENU/BRIGHT wheel to select
“RETURN” and press it. Selection is complete.
“SAVE?” appears.
DPOF Screen
DPOF
• If you did not change any settings in step 3 through
5, the Menu Screen reappears.
SHEETS
7
Rotate the MENU/BRIGHT wheel to select
“EXECUTE”, then press it to save the setting you
have just made.
0 0
RETURN
• To cancel selection, rotate the MENU/BRIGHT
wheel to select “CANCEL” and press it.
DPOF
To Reset The No. Of Prints . . .
..... select “RESET” in step 5 on pg. 34. The number
of prints is reset to 0 for all still images.
SHEETS
0 5
CAUTION
While performing the above, never disconnect power, as
this may cause the memory to be corrupted. For safety,
all buttons including the Power Switch are disabled in
step 6.
DPOF
NOTES:
● “BATTERY LOW” appears if the battery remaining
power is too low.
SAVE?
● If you load a memory card already set as shown above
in a printer compatible with DPOF, it will make prints of
the selected still images automatically.
● To print images recorded on a tape, first dub them to a
memory card (੬ pg. 32).
EXECUTE
CANCEL
36EN
ADVANCED FEATURES (cont.)
Making A New Folder
New still pictures you are going to take can be
separated from previously shot pictures by resetting
the file name to DVC00001; these new pictures will
be stored in a new folder.
Folder and File names
Each time shooting takes place, a file name is
made using a number which is larger by one than
the largest number of the file names which are in
use. Even if you delete an image file with a
number in the middle of range, the number will
not be used for a new shot; a gap will remain in
the numerical sequence. If the file name reaches
DVC09999, a new folder (such as “101JVCGR”)
will be made and the file name will start again
from DVC00001.
1
Set the VIDEO/MEMORY Switch to “MEMORY”,
then set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
• A stored file is displayed.
2
Make sure an IMAGE file is displayed
(੬ pg. 28); if not, press SELECT to access the
MEMORY SELECT Screen. Rotate the MENU/
BRIGHT wheel to select “IMAGE” and press it.
MENU/BRIGHT Wheel
3
Press the MENU/BRIGHT wheel in. The Menu
Screen appears. Rotate the MENU/BRIGHT wheel to
select “NO. RESET”, then press it. The NO. RESET
Screen appears.
VIDEO/MEMORY Switch (Open the
LCD monitor to access this switch.)
4
Rotate the MENU/BRIGHT wheel to select
“EXECUTE”, then press it. The new folder (such as
“101JVCGR”) will be made and the file name of the
next shot starts from DVC00001.
Initialising A Memory Card
You can initialise a memory card anytime.
After initialising, all files and data stored on the
memory card, including those which have been
protected, are cleared.
SELECT Button
1
2
Perform step 1 of “Making A New Folder” above.
MANUAL
AUTO
Lock Button
Press the MENU/BRIGHT wheel in. The Menu
OFF
Screen appears. Rotate the MENU/BRIGHT wheel to
select “FORMAT” and press it. The FORMAT Screen
appears.
PLAY
Power Switch
3
Rotate the MENU/BRIGHT wheel to select
Display
“EXECUTE” and press it. The memory card is
initialised. When initialisation is finished, “NO
IMAGES STORED” or “NO E-MAIL CLIP STORED”
appears.
FORMAT
Menu Screen
ERASE ALL
EX I ST I NG DATA?
• To cancel initialisation, rotate the MENU/BRIGHT
wheel to select “RETURN” and press it.
EXECUTE
RETURN
CAUTION
Do not perform any other operation (such as turning
off the camcorder) during initialisation. Also, be sure
to use the provided AC Adapter, as the memory card
may be corrupted if the battery becomes exhausted
during initialisation. If the memory card becomes
corrupted initialise it.
EN 37
ADVANCED FEATURES
ADVANCED FEATURES
CONTENTS
FOR RECORDING ........................................... 38 – 45
Night-Scope............................................................ 38
Programme AE With Special Effects ..........................38 – 39
Fade/Wipe Effects .............................................40 – 41
Snapshot (For Tape Recording)....................................... 42
Auto Focus/Manual Focus ............................................ 43
Exposure Control ...................................................... 44
Iris Lock ................................................................ 44
White Balance Adjustment ........................................... 45
Manual White Balance Operation.................................... 45
USING MENUS FOR DETAILED ADJUSTMENT............. 46 – 51
For Recording Menu............................................46 – 49
For Playback Menu ............................................50 – 51
DUBBING .................................................... 52 – 53
Dubbing To A VCR..................................................... 52
Dubbing To Or From A Video Unit Equipped With A DV Connector .... 53
USING THE REMOTE CONTROL UNIT ..................... 54 – 64
Installing The Batteries ............................................... 54
Slow-Motion Playback ............................................... 56
Frame-By-Frame Playback ........................................... 56
Playback Special Effects .............................................. 56
Playback Zoom ........................................................ 57
Random Assemble Editing .....................................58 – 62
For More Accurate Editing ............................................ 62
Audio Dubbing ......................................................... 63
Insert Editing .......................................................... 64
SYSTEM CONNECTIONS .................................... 65 – 66
Connection To A Personal Computer ................................. 65
Using The Camcorder As A WebCam
(GR-DVL867/DVL865 only) ............................................... 66
38EN
FOR RECORDING
NOTES:
Night-Scope
● During Night-Scope, the following functions or settings
cannot be activated and its indicator blinks or goes out:
• Some modes of “Programme AE With Special Effects”
(੬ pg. 38, 39).
• “GAIN UP” in the CAMERA Menu (੬ pg. 47).
• “DIS” in the MANUAL Menu (੬ pg.47).
• “Video light” when LIGHT OFF/AUTO/ON is set to
“AUTO” (੬ pg. 19).
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is
strobing due to the slow shutter speed.
MANUAL
” while pressing
1
Set the Power Switch to “
down the Lock Button located on the switch.
● During Night-Scope, it may be difficult to bring the
camcorder into focus. To prevent this, use of manual
focus and/or a tripod is recommended.
2
Press NIGHT so that the Night-Scope indicator
”appears.
• The shutter speed is automatically adjusted to
“
provide up to 30 times sensitivity.
• “A” appears beside “
” while the shutter speed is
being automatically adjusted.
To Deactivate Night-Scope . . .
..... press NIGHT again so that the Night-Scope
indicator disappears.
MENU/BRIGHT Wheel
Programme AE With Special Effects
MANUAL
” while pressing
down the Lock Button located on the switch.
Lock Button
1
Set the Power Switch to “
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
Rotate the MENU/BRIGHT wheel to select “
Power Switch
NIGHT Button
3
PROGRAMME AE”, then press it.
4
Rotate the MENU/BRIGHT wheel to select the
desired mode (੬ pg. 39), then press it. Selection is
complete. Press the MENU/BRIGHT wheel in again.
The Menu Screen closes.
• The PROGRAMME AE Menu disappears and the
selected mode is activated. The selected mode
indicator appears.
To Deactivate The Selected Mode . . .
..... select “OFF” in step 4.
NOTES:
● Programme AE with special effects can be changed
during recording or during Record-Standby.
● Some modes of Programme AE special effects cannot
be used during Night-Scope.
Display
ᮡ
SNO
W
SPOTL I GHT
TW
I L I GHT
SEP I A
MONOTONE
CLASS I C F I LM
STROBE
IMPORTANT
Some modes of Programme AE with special effects
cannot be used with certain Fade/Wipe Effects
(੬ pg. 40, 41). If an unusable mode is selected, its
indicator blinks or goes out.
SLO
SLO
W
4
X
W
10
X
ᮢ
GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only
EN 39
SEPIA
SHUTTER
Recorded scenes have a brownish tint like old
photos. Combine this with the Cinema mode for a
classic look.
1/50–The shutter speed is fixed at 1/50th of a
second. Black bands that usually appear when
shooting a TV screen become narrower.
1/120–The shutter speed is fixed at 1/120th of a
second. The flickering that occurs when shooting
under a fluorescent light or mercury-vapour lamp is
reduced.
MONOTONE
Like black and white films, your footage is shot in
B/W. Used together with the Cinema mode, it
enhances the “classic film” effect.
SPORTS
(Variable
Shutter Speed:
1/250 – 1/4000)
CLASSIC FILM*
Gives recorded scenes a strobe effect.
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable slow-
motion playback. The faster the shutter speed, the
darker the picture becomes. Use the shutter
function under good lighting conditions.
SNOW
Compensates for subjects that may otherwise
appear too dark when shooting in extremely bright
surroundings such as in the snow.
STROBE*
Your recording looks like a series of consecutive
snapshots.
SPOTLIGHT
Compensates for subjects that may otherwise
appear too bright when shooting under extremely
strong direct lighting such as spotlights.
SLOW (Slow Shutter) (GR-DVL567/DVL367/
DVL365/DVL167/DVL160 only)
Lights dark subjects or areas even brighter than
they would be under good natural lighting. Use
“SLOW” only in dark areas.
NOTE:
“SPOTLIGHT” has the same effect as –3 with the
exposure control (੬ pg. 44).
SLOW 4X
Slow Shutter raises light sensitivity to allow
shooting in dark environments.
SLOW 10X
Slow Shutter raises light sensitivity further to allow
shooting in even darker environments.
NOTES:
● When using “SLOW”, the image takes on a strobe-
like effect.
TWILIGHT
● When using “SLOW”, it may be difficult to bring the
camcorder into focus. To prevent this, use of manual
focus and/or a tripod is recommended.
Makes evening scenes look more natural.
White Balance (੬ pg. 45) is initially set to
can be changed to your desired setting. When
, but
Twilight is chosen, the camcorder automatically
adjusts the focus from approx. 10 m to infinity.
From less than 10 m, adjust the focus manually.
* For GR-DVL867/DVL865/DVL767/DVL765 Owners:
Available when the VIDEO/MEMORY Switch is set to
“VIDEO”.
40 EN
FOR RECORDING (cont.)
Fade/Wipe Effects
These effects let you make pro-style scene transi-
tions. Use them to spice up the transition from one
scene to the next.
IMPORTANT
Some Fade/Wipe Effects cannot be used with certain
modes of Programme AE with special effects
(੬ pg. 38, 39). If an unusable Fade/Wipe Effect is
selected, its indicator blinks or goes out.
Fade or Wipe works when tape recording is started
or when you stop recording.
1
Set the VIDEO/MEMORY Switch to “VIDEO”
Lock Button
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 only), then set the Power Switch to
MANUAL
MENU/BRIGHT Wheel
“
” while pressing down the Lock Button
located on the switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
Rotate the MENU/BRIGHT wheel to select “
3
WIPE/FADER”, then press it.
4
Rotate the MENU/BRIGHT wheel to select the
desired function, then press it. Selection is complete.
Press the MENU/BRIGHT wheel in again.
• The WIPE/FADER Menu disappears and the effect
is reserved. The indicator representing the selected
effect appears.
Power Switch
Recording Start/Stop Button
5
Press the Recording Start/Stop Button to activate
the Fade-in/out or Wipe-in/out.
VIDEO/MEMORY Switch
To Deactivate The Selected Effect . . .
..... select “OFF” in step 4.
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only; open the
LCD monitor to access this switch.)
NOTE:
You can extend the length of a Fade or Wipe by pressing
and holding the Recording Start/Stop Button.
EN 41
Fader And Wipe Menu
Menu
Effect
Fade in or out with a white screen.
FADER — WHITE
Fade in or out with a black screen.
FADER — BLACK
FADER — B.W
Fade in to a colour screen from a black and white screen, or fade out
from colour to black and white.
Wipe in on a black screen from the upper right to the lower left corner,
or wipe out from lower left to upper right, leaving a black screen.
WIPE — CORNER
WIPE — WINDOW
WIPE — SLIDE
The scene starts in the centre of a black screen and wipes in toward
the corners, or comes in from the corners, gradually wiping out to the
centre.
Wipe in from right to left, or wipe out from left to right.
Wipe in as the two halves of a black screen open to the left and right,
revealing the scene, or wipe out and the black screen reappears from
left and right to cover the scene.
WIPE — DOOR
The scene wipes in from the bottom to the top of a black screen, or
wipes out from top to bottom, leaving a black screen.
WIPE — SCROLL
WIPE — SHUTTER
Wipe in from the centre of a black screen toward the top and bottom,
or wipe out from the top and bottom toward the centre leaving a black
screen.
42 EN
FOR RECORDING (cont.)
SNAPSHOT Button
Snapshot (For Tape Recording)
This feature lets you record still images that look like
photographs onto a tape.
Power Switch
SNAPSHOT MODE SELECTION
1
Set the VIDEO/MEMORY Switch to “VIDEO” (GR-
DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
MANUAL
DVL365 only), then set the Power Switch to “
”
while pressing down the Lock Button located on the
switch.
Lock Button
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select “
CAMERA”. Press it and the CAMERA Menu appears.
VIDEO/MEMORY Switch
(GR-DVL867/DVL865/
DVL767/DVL765/
4
Rotate the MENU/BRIGHT wheel to select
“SNAP MODE”, then press it.
DVL567/DVL367/
DVL365 only; open the
LCD monitor to access
this switch.)
5
Rotate the MENU/BRIGHT wheel to select the
desired Snapshot mode, then press it.
Rotate the MENU/BRIGHT wheel to select
“
RETURN” and press it twice. The Menu Screen
closes.
SNAPSHOT RECORDING
Display
Menu Screen
1
Press SNAPSHOT. “PHOTO” appears while the
snapshot is being taken.
If you press during Record-Standby . . .
...... “PHOTO” appears and a still image will be recorded for
approx. 6 seconds, then the camcorder re-enters the
Record-Standby mode.
SNAP MODE
–
FULL
P I N–UP
FRAME
GR-DVL867/DVL865/
DVL767/DVL765/
DVL567/DVL367/
DVL365 only
If you press during Recording . . .
...... “PHOTO” appears and a still image will be recorded for
approx. 6 seconds, then the normal recording resumes.
AUTO
• Regardless of the Power Switch position (“
” or
MANUAL
“
”), Snapshot recording takes place using the
FULL
selected Snapshot mode.
Snapshot mode
with no frame
Motor Drive Mode
Keeping SNAPSHOT pressed provides an effect similar to
serial photography. (Interval between still images: approx.
1 second)
NOTES:
● To remove the shutter sound, ੬ “BEEP” on pg. 46, 48.
● If Snapshot recording is not possible, “PHOTO” blinks when
SNAPSHOT is pressed.
● If Programme AE with special effects (੬ pg. 38) is
engaged, certain modes of Programme AE with special
effects are disabled during Snapshot recording. In such a
case, the icon blinks.
PIN-UP
Pin-Up mode
● If SNAPSHOT is pressed when “DIS” is set to “ON”
(੬ pg. 47), the Stabiliser will be disabled.
● The Motor Drive mode is disabled when “REC SELECT” is
set to “
/
” in the Menu Screen (੬ pg. 49).
● If “REC SELECT” is set to “
/
” in the DSC
FRAME
Snapshot mode
with frame
Menu Screen, still images are recorded on the memory card
as well (640 X 480 pixels).
● During tape playback as well, all snapshot modes are
available when “
COPY” is set to “OFF” in the
Menu Screen (੬ pg. 50). However, the shutter sound is
not heard.
● During Snapshot recording, the image displayed in the
viewfinder may be partially missing. However, there is no
effect in the recorded image.
● When a cable is connected to the AV connector, the shutter
sound is not heard from the speaker, however it is recorded
onto the tape.
There is the sound effect of a shutter closing.
EN 43
Focus detection zone
While focusing on a further
subject
While focusing on a nearer
subject
FEATURE: Auto Focus
PURPOSE:
The camcorder’s Full Range AF system offers continuous shooting ability from close-up (as close as approx.
5 cm to the subject) to infinity.
However, correct focus may not be obtainable in the situations listed below (in these cases use manual
focusing):
• When two subjects overlap in the same scene.
• When illumination is low.*
• When the subject has no contrast (difference in brightness and darkness), such as a flat, one-colour wall, or
a clear, blue sky.*
• When a dark object is barely visible in the viewfinder.*
• When the scene contains minute patterns or identical patterns that are regularly repeated.
• When the scene is affected by sunbeams or light reflecting off the surface of a body of water.
• When shooting a scene with a high-contrast background.
* The following low-contrast warnings appear blinking:
,
,
and
NOTES:
● If the lens is smeared or blurred, accurate focusing is not possible. Keep the lens clean, wiping with a piece of soft
cloth if it gets dirty. When condensation occurs, wipe with a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom out first (੬ pg. 18). If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out depending on the distance between the camcorder and the subject. This
will not occur when “TELE MACRO” (੬ pg. 48) is activated.
FEATURE: Manual Focus
PURPOSE:
To obtain correct focus.
OPERATION:
1) If you are using the viewfinder, you should already have made the necessary viewfinder adjustments
(੬ pg. 10).
2) Set the Power Switch to “
MANUAL
” while pressing down the Lock Button located on the switch, then press
FOCUS (੬ pgs. 80 and 81, # FOCUS Button). The manual focus indicator appears.
3) To focus on a farther subject, rotate the MENU/BRIGHT wheel towards “+”. “ ” appears and blinks.
To focus on a nearer subject, rotate the MENU/BRIGHT wheel towards “–”. “ ” appears and blinks.
4) Press the MENU/BRIGHT wheel in. Focus adjustment is complete.
AUTO
To reset to Auto Focus, press FOCUS twice or set the Power Switch to “
”.
If FOCUS is pressed once, the camcorder will enter the focus adjustment mode again.
NOTES:
● Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode. If you focus in
on a subject in the wide-angle position, sharply focused images cannot be obtained when zoomed up because the
depth-of-field is reduced at longer focal lengths.
● When the focus level cannot be adjusted any further or closer, “ ” or “ ” will blink.
44 EN
FOR RECORDING (cont.)
Exposure Control
Iris Lock
Manual exposure adjustment is recommended in the
following situations:
Use this function in the following situations:
• When shooting a moving subject.
• When shooting using reverse lighting or when the
background is too bright.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When the background is overly dark or the subject
light.
• When the distance to the subject changes (so its
size in the LCD monitor or the viewfinder changes),
such as when the subject is backing away.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When shooting objects under a spotlight.
• When zooming.
When the subject is close, keep the iris locked. Even
when the subject moves away from you, the image
will not darken or brighten.
MANUAL
” while pressing
down the Lock Button located on the switch.
1
Set the Power Switch to “
2
Press the MENU/BRIGHT wheel in. The Menu
Before the following steps, perform steps 1
through 4 of “Exposure Control”.
Screen appears.
Rotate the MENU/BRIGHT wheel to select “
3
5
Adjust zoom so that the subject fills the LCD
EXPOSURE”, then press it.
monitor or the viewfinder, then press and hold the
MENU/BRIGHT wheel for over 2 seconds. The
exposure control indicator and “ ” appear.
4
Rotate the MENU/BRIGHT wheel to select
“MANUAL”, then press it. The Menu Screen disap-
pears. The exposure control indicator appears.
Press the MENU/BRIGHT wheel in. “ ” changes to
“
” and the iris is locked.
5
Rotate the MENU/BRIGHT wheel towards “+” to
brighten the image, or towards “–” to darken the
image. (maximum 6)
Iris lock indicator
6
Press the MENU/BRIGHT wheel in. Exposure
adjustment is complete.
3
MENU/BRIGHT
Wheel
To Return To Automatic Exposure Control . . .
..... select “AUTO” in step 4. Or, set the Power Switch
AUTO
to “
”.
BACKLIGHT Button (5)
To Brighten The Subject Quickly . . .
..... press BACKLIGHT.
is displayed and the
subject is brightened. If pressed again,
disappears and the brightness returns to the
previous level.
• +3 exposure has the same effect as the
BACKLIGHT Button.
• Using BACKLIGHT may cause the light around the
subject to become too bright and the subject to
become white.
Power Switch
• Backlight compensations is also available when the
AUTO
Power Switch is set to “
”.
To Return To Automatic Iris Control . . .
..... rotate MENU/BRIGHT to display “AUTO” then
press it in step 4. The exposure control indicator
and “ ” disappear. Or, set the Power switch to
AUTO
NOTE:
You cannot use the manual exposure control at the same
time with backlight, spotlight (੬ pg. 39) compensation
and “SNOW” (੬ pg. 39).
“
”.
To Lock The Exposure Control And The Iris . . .
..... after step 4 of “Exposure Control”, adjust the
exposure rotating the MENU/BRIGHT wheel.
Then lock the iris in step 5 of “Iris Lock”. For
automatic locking, rotate the MENU/BRIGHT
wheel to select “AUTO”, then press it in step 4.
The iris becomes automatic after about 2
seconds.
Iris
Like the pupil of the human eye, it contracts in well-lit
environments to keep too much light from entering,
and dilates in dim environments to allow in more light.
EN 45
White Balance Adjustment
Manual White Balance Operation
A term that refers to the correctness of colour
reproduction under various lighting. If the white
balance is correct, all other colours will be accurately
reproduced.
Perform Manual White Balance when shooting under
various types of lighting.
1
Follow steps 1 through 4 of the white balance
adjustment, and select “ MWB”.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators
control this function manually to achieve a more
professional colour/tint reproduction.
2
Hold a sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so that the
white paper fills the screen.
MANUAL
” while pressing
down the Lock Button located on the switch.
1
Set the Power Switch to “
3
Press the MENU/BRIGHT wheel in until
begins blinking rapidly.
When the setting is completed,
blinking.
resumes normal
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
4 Press the MENU/BRIGHT wheel in twice. The
Menu Screen closes and the Manual White Balance
indicator is displayed.
3
Rotate the MENU/BRIGHT wheel to select
W.BALANCE”, then press it. The W.BALANCE
Menu appears.
“
4
Rotate the MENU/BRIGHT wheel to select the
desired mode.
“AUTO” ................. White balance is adjusted
automatically (factory preset).
MENU/BRIGHT Wheel
“
“
“
“
MWB” ............ White balance is set manually.
FINE” ............. Outdoors on a sunny day.
CLOUD” ........ Outdoors on a cloudy day.
HALOGEN” ... A video light or similar type of
lighting is used.
White paper
5
Press the MENU/BRIGHT wheel in. Selection is
complete. Press the MENU/BRIGHT wheel in again.
The Menu Screen closes and the selected mode
indicator except “AUTO” appears.
Power Switch
To Return To Automatic White Balance . . .
..... select “AUTO” in step 4. Or, set the Power Switch
AUTO
to “
”.
NOTE:
White balance cannot be used when Sepia or Monotone
NOTES:
(੬ pg. 39) is activated.
● In step 2, it may be difficult to focus on the white paper.
In such a case, adjust focus manually (੬ pg. 43).
● A subject can be shot under various types of lighting
conditions indoors (natural, flourescent, candlelight,
etc.). Because the colour temperature is different
depending on the light source, the subject tint will differ
depending on the white balance settings. Use this
function for a more natural result.
● Once you adjust white balance manually, the setting is
retained even if the power is turned off or the battery
removed.
46 EN
USING MENUS FOR DETAILED ADJUSTMENT
MENU/BRIGHT Wheel
For Recording Menu
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the
more detailed camcorder settings (੬ pg. 47 – 49).
Lock Button
MANUAL
” while pressing
1
Set the Power Switch to “
down the Lock Button located on the switch.
Power Switch
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select the
desired function menu, and press it. The selected
function menu appears.
Display
W I P E / FADER
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
OF
F
Menu Screen
4
Function menu setting depends on the function.
If you have selected “
WIPE/FADER”,
EXPOSURE” or
MANUAL
REC MODE
SOUND MODE
ZOOM
SNAP MODE
GA I N UP
–
–
–
–
–
SP
SYSTEM
“
“
PROGRAM AE”, “
12B I T
D I SPLAY
DSC
40
FULL
AGC
X
W. BALANCE” . . .
END
..... see pg. 47.
If you have selected “
CAMERA”, “
RETURN
MANUAL”, “
SYSTEM”, “
DISPLAY” or
“
DSC” (GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) . . .
..... go to step 5.
Sub Menu
D I S
–
OFF
ON
5
Rotate the MENU/BRIGHT wheel to select the
desired function and press it. The Sub Menu appears.
Then, rotate the MENU/BRIGHT wheel to select the
parameter, and press it. Selection is complete.
6
Rotate the MENU/BRIGHT wheel to select
“
RETURN” and press it twice. The Menu Screen
closes.
BEEP
–
–
–
–
–
MELODY
ON
• The
icon represents “END”.
TALLY
I D NUMBER
DEMO MODE
S I DE LED
CAM RESET
0 6
ON
ON
NOTE:
When the Menu Screen is left on for a couple of
minutes, a residual image may be left on the screen
and it may take several seconds for the residual
image to disappear. This is not due to any defect of
the unit.
RETURN
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF
2 5 . 12 . 02
17 : 3 0
ADJ .
RETURN
QUAL I TY
I MAGE S I ZE
REC SELECT
–
–
–
F I NE
1024X768
W I P E / FADER
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
RETURN
MANUAL
SYSTEM
D I SPLAY
DSC
END
Normal Screen
* Actual menus differ by model and may appear
differently from these illustrations. Some menu items
may be unavailable on your model.
EN 47
Menu Screen Explanations
WIPE/FADER
PROGRAM AE
EXPOSURE
Refer to “Fade/Wipe Effects” (੬ pg. 40, 41).
Refer to “Programme AE With Special Effects” (੬ pg. 38, 39).
Refer to “Exposure Control” and “Iris Lock” (੬ pg. 44).
W.BALANCE
Refer to “White Balance Adjustment” and “Manual White Balance Operation”
(੬ pg. 45).
REC MODE
Allows you to set the tape recording mode (SP or LP) depending on your
preference (੬ pg. 13).
SOUND
MODE
12BIT
Enables tape recording of stereo sound on four separate channels, and is
recommended for use when performing audio dubbing. (Equivalent to the
32 kHz mode of previous models)
16BIT
10X
Enables tape recording of stereo sound on two separate channels. (Equivalent
to the 48 kHz mode of previous models)
ZOOM
When set to “10X” while using digital zoom, the zoom magnification will reset to
10X since digital zoom will be disengaged.
40X
Allows you to use the Digital Zoom. By digitally processing and magnifying
images, zooming is possible from 10X (the optical zoom limit), to a maximum
of 40X digital magnification.
500X
Allows you to use the Digital Zoom. By digitally processing and magnifying
images, zooming is possible from 10X (the optical zoom limit), to a maximum
of 500X digital magnification.
SNAP MODE
GAIN UP OFF
AGC
Refer to “Snapshot (For Tape Recording)” (੬ pg. 42).
Allows you to shoot dark scenes with no picture brightness adjustment.
The overall appearance may be grainy, but the image is bright.
AUTO
The shutter speed is automatically adjusted (1/25 — 1/200 sec.). Shooting a
subject in low or poor lighting at 1/25 sec. shutter speed provides a brighter
image than in the AGC mode, but the subject’s movements are not smooth or
natural. The overall appearance may be grainy. While the shutter speed is
being automatically adjusted, “
” is displayed.
DIS
OFF
ON
To compensate for unstable images caused by camera-shake, particularly at
high magnification.
NOTES:
● Accurate stabilisation may not be possible if hand shake is excessive, or
under the following conditions:
• When shooting subjects with vertical or horizontal stripes.
• When shooting dark or dim subjects.
• When shooting subjects with excessive backlighting.
• When shooting scenes with movement in various directions.
• When shooting scenes with low-contrast backgrounds.
● Switch off this mode when recording with the camcorder on a tripod.
● The “
” indicator blinks or goes out if the Stabiliser cannot be used.
: Factory-preset
NOTES:
MANUAL
”.
AUTO
● Settings made in the “
CAMERA” Menu remain effective whether the Power Switch is set to “
” or “
MANUAL
However, the menu settings can be changed only when the Power Switch is set to “
● The “
”.
MANUAL
”.
MANUAL” settings are effective only when the Power Switch is set to “
CONTINUED ON NEXT PAGE
48 EN
USING MENUS FOR DETAILED ADJUSTMENT (cont.)
Menu Screen Explanations (cont.)
TELE
MACRO
OFF
Usually the distance to a subject where the lens is in focus depends on the
zoom magnification. Unless there is a distance more than 1m to the subject,
the lens is out of focus at the maximum telephoto setting. When set to “ON”,
you can shoot a subject as large as possible at a distance of approx. 60 cm.
• Depending on the zoom position, the lens may go out of focus.
ON
WIDE
MODE
OFF
Records with no change in the screen ratio. For playback on a TV with a
normal screen ratio.
CINEMA
Inserts black bands at the top and bottom of the screen. During playback on
wide-screen TVs, the black bands at the top and bottom of the screen are cut
and the screen ratio becomes 16:9.
appears. When using this mode, refer
to your wide-screen TV’s instruction manual. During playback/recording on 4:3
TVs/LCD monitor/viewfinder, black bands are inserted at the top and bottom of
the screen and the image appears like a letterboxed 16:9 movie.
• The “CINEMA” mode is effective only when the VIDEO/MEMORY Switch is
set to “VIDEO” (GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only).
SQUEEZE For playback on TVs with an aspect ratio of 16:9. Naturally expands the image
to fit the screen without distortion. appears. When using this mode, refer to
your wide-screen TV’s instruction manual. During playback/recording on 4:3
TVs/LCD monitor/viewfinder, the image is elongated vertically.
• The “SQUEEZE” mode is effective only when the VIDEO/MEMORY Switch is
set to “VIDEO” (GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only).
S.WIDE
“
” appears. The zoom range is extended beyond the maximum optical zoom
wide angle range. This mode’s wide angle setting is equivalent to using a 0.9X
wide conversion lens. Zooming is possible from 0.9X to 10X. This mode is
suitable for shooting in a small room.
(GR-DVL867/
DVL865/
DVL767/
• “S.WIDE” mode is effective only when the VIDEO/MEMORY Switch is set to
DVL765 only)
“VIDEO”.
WIND
CUT
OFF
ON
Disengages the function which cuts down on noise created by wind.
Helps cut down on noise created by wind. “
” appears. The quality of the
sound will change. This is normal.
BEEP
OFF
Even though not heard while shooting, shutter sound is recorded on the tape.
BEEP
The beep sounds when the power is turned on or off, and at the beginning and
end of recording. Also to activate the shutter sound effect (੬ pg. 26, 42).
MELODY
Instead of a beep, a melody sounds when any operation is performed. It also
activates the shutter sound effect (੬ pg. 26, 42).
TALLY
OFF
ON
The tally lamp remains off at all times.
The tally lamp comes on to signal the start of recording.
ID NUMBER
This number is necessary when connecting the camcorder to a device such as
a computer using the J terminal (JLIP) or PC connector. The numbers range
from 01 to 99. Factory setting is 06.
(GR-DVL167/DVL160 only)
: Factory-preset
NOTES:
MANUAL
”.
● The “
MANUAL” settings are effective only when the Power Switch is set to “
SYSTEM” functions which are set when the Power Switch is set to “ MANUAL ” are also applied when the Power
● “
Switch is set to “PLAY” (੬ pg. 50).
EN 49
DEMO
MODE
OFF
ON
Automatic demonstration will not take place.
Demonstrates certain functions such as Programme AE with special effects,
etc., and can be used to confirm how these functions operate.
Demonstration starts in the following cases:
• When the Menu Screen is closed after “DEMO MODE” is turned “ON”.
• With “DEMO MODE” set to “ON”, if there is no operation for about 3 minutes
AUTO
MANUAL
” .
after the Power Switch is set to “
” or “
Performing any operation during the demonstration stops the demonstration
temporarily. If no operation is performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
● If a tape is in the camcorder, the demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the camcorder power is turned off.
● If “DEMO MODE” remains “ON”, some functions will not be available. After
viewing demo, set to “OFF”.
SIDE LED
(GR-DVL867/
DVL865/DVL767/
DVL765 only)
ON
The Side LED indicator (੬ p. 80, 81) lights on the camcorder when the Power
AUTO
MANU
AL
”.
Switch is set to “
” or “
OFF
Does not reset all settings to the factory-preset.
Resets all settings to the factory-preset.
CAM
CANCEL
EXECUTE
LCD
RESET
Keeps the camcorder’s display (except the date, time and time code) from
appearing on the connected TV screen.
ON
SCREEN
Makes the camcorder’s display appear on screen when the camcorder is
connected to a TV.
LCD/TV
The date/time does not appear.
DATE/
TIME
OFF
Displays the date/time for approx. 5 seconds in the following cases:
AUTO
MANUAL
”.
AUTO
• When the Power Switch is set from “OFF” to “
” or “
• When tape playback starts. The camcorder displays the date/time when
scenes are recorded.
• When the date is changed during tape playback.
The date/time is always displayed.
Time code is not displayed.
ON
TIME
CODE
OFF
ON
Time code is displayed on the camcorder and on the connected TV. Frame
numbers are not displayed during recording.
Allows you to set the current date and time (੬ pg. 11).
CLOCK ADJ.
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only)
QUALITY
Refer to “Picture Quality/Image Size Setting” (੬ pg. 14).
IMAGE SIZE
REC
SELECT
When Snapshot recording is performed with the VIDEO/MEMORY Switch set
to “VIDEO”, still images are recorded only onto the tape.
When Snapshot recording is performed with the VIDEO/MEMORY Switch set
to “VIDEO”, still images are recorded not only onto the tape but also on the
memory card (640 x 480 pixels). In this mode, the “SNAP MODE” selection in
the CAMERA Menu is also applicable to memory card recording.
/
: Factory-preset
NOTES:
MANUAL
” are also applied
●
“
SYSTEM” and “
DISPLAY” functions which are set when the Power Switch is set to “
when the Power Switch is set to “PLAY” (
੬
pg. 50). “CLOCK ADJ.” only appears when the Power Switch is set to
MANUAL
“
”.
AUTO
”. However,
● Settings made in the “
the menu settings can be changed only when the Power Switch is set to “
DISPLAY” Menu remain effective even when the Power Switch is set to “
MANUAL
”.
● The date indication can also be turned on/off by pressing the DISPLAY Button on the remote control (provided)
(੬ pg. 23, 52, 59).
50 EN
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only; open the
LCD monitor to access this switch.)
USING MENUS FOR DETAILED ADJUSTMENT (cont.)
VIDEO/MEMORY Switch
For Playback Menu
The following procedure applies to all except Synchro
Comp (੬ pg. 62).
Power Switch
1
Set the VIDEO/MEMORY Switch to “VIDEO” (GR-
MENU/BRIGHT Wheel
DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only), then set the Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select the
desired function menu, and press it. The selected
function menu appears.
Display
4
Rotate the MENU/BRIGHT wheel to select the
V I DEO
SYSTEM
D I SPLAY
SOUND MODE
12B I T MODE
SYNCHRO
REC MODE
COPY
Lock Button
desired function, and press it to display the Sub Menu.
5
Rotate the MENU/BRIGHT wheel to select the
Recording
Start/Stop Button
desired parameter and press it. Selection is complete.
6
Rotate the MENU/BRIGHT wheel to select “
RETURN” and press it twice to close the Menu Screen.
END
Menu Screen Explanations
SOUND MODE ੬ pg. 51.
SOUND MODE
–
–
–
–
–
STEREO
SOUND
O . O
12BIT MODE
SYNCHRO
REC MODE
੬ pg. 51.
12B I T MODE
SYNCHRO
REC MODE
COPY
1
੬ pg. 62.
SP
OFF
Allows you to set the tape
recording mode (SP or LP)
depending on your preference
(੬ pg. 13). It is recommended
you use “REC MODE” in the
RETURN
“
VIDEO” Menu when using
this camcorder as a recorder
during dubbing (GR-DVL867/
DVL767/DVL567/DVL367/
DVL167 only ੬ pg. 53).
BEEP
–
–
–
–
–
MELODY
ON
TALLY
I D NUMBER
DEMO MODE
S I DE LED
CAM RESET
06
ON
ON
COPY ON: Enables dubbing of images
(GR-DVL867/ recorded on a tape to a memory
DVL865/DVL767/ card (੬ pg. 32).
DVL765/DVL567/ OFF: Enables snapshots to be
DVL367/DVL365 taken during tape playback.
only)
RETURN
ON SCREEN
DATE / T I ME
T I ME CODE
–
–
–
LCD / TV
AUTO
OFF
Each setting is linked with “
DISPLAY” or “
SYSTEM”, which
appears when the Power Switch is
MANUAL
set to “
” (੬ pg. 48, 49).
The parameters are the same as in
the description on pg. 48, 49.
RETURN
* Actual menus differ by model and may appear
differently from these illustrations. Some menu items
may be unavailable on your model.
NOTES:
● The date indication can also be turned on/off by
pressing DISPLAY on the remote control (provided).
● “REC MODE” can be set when the Power Switch is set
MANUAL
to “PLAY” or “
” (੬ pg. 13, 47).
EN 51
Playback Sound
During tape playback, the camcorder detects the sound mode in which the recording was made, and plays the
sound back. Select the type of sound to accompany your playback picture. According to the menu access
explanation on pg. 50, select “SOUND MODE” or “12BIT MODE” from the Menu Screen and set it to the desired
parameter.
STEREO
SOUND MODE SOUND L
SOUND R
Sound is output on both “L” and “R” channels in stereo.
Sound from the “L” channel is output in stereo.
Sound from the “R” channel is output in stereo.
MIX
Original and dubbed sounds are combined and output in stereo on both
“L” and “R” channels in stereo.
12BIT MODE
SOUND 1
Original sound is output on both “L” and “R” channels in stereo.
SOUND 2
Dubbed sound is output on both “L” and “R” channels in stereo.
: Factory-preset
NOTES:
● The “SOUND MODE” setting is available for both 12-bit and 16-bit sound. (In previous models’ functions, “12-bit” is
called “32 kHz” and “16-bit” is called “48 kHz”.)
● The camcorder cannot detect the sound mode in which the recording was made during fast-forward or rewind. During
playback the sound mode is displayed in the upper left corner.
Display
ON SCREEN setting:
For playback sound, tape
speed and tape running.
DATE/TIME setting:
For date/time.
TIME CODE setting:
For time code.
4
12B I T / SOUND
L
1
SP
6
2 5 . 12 . 02
17 : 3 0
12 : 34 : 24
Frames*
Seconds
Minutes
*25 frames = 1 second
52 EN
DUBBING
Connector cover*
Dubbing To A VCR
Power Switch
1
Following the illustration, connect the camcorder
and the VCR. Also refer to pg. 22 and 23.
To AV
2
Set the VIDEO/MEMORY Switch to “VIDEO” (GR-
DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/
DVL365 only), then set the camcorder’s Power Switch
to “PLAY” while pressing down the Lock Button
located on the switch, turn on the VCR’s power, and
insert the appropriate cassettes in the camcorder and
the VCR.
To
S-VIDEO
3
4 Engage the VCR’s AUX and Record-Pause modes.
Engage the camcorder’s Play mode to find a spot
Audio/Video cable
[mini-plug to RCA plug]
(provided)
just before the edit-in point. Once it is reached, press
4/6 on the camcorder.
5
Press 4/6 on the camcorder and engage the
VCR’s Record mode.
S-Video cable
(optional)
6
Engage the VCR’s Record-Pause mode and
press 4/6 on the camcorder.
7
NOTES:
Repeat steps 4 through 6 for additional editing,
then stop the VCR and camcorder when finished.
To AUDIO, VIDEO**
and
-IN
connectors
● As the camcorder starts to play your footage it will
appear on your TV. This will confirm the connections
and the AUX channel for dubbing purposes.
● Before you start dubbing, make sure that the indications
do not appear on the connected TV. If they do, they are
being recorded onto the new tape.
“Y/C”/“CVBS”
video out
select switch
Cable Adapter (provided)
If your VCR has a SCART
connector, use the
provided cable adapter.
● Set the video out select switch of the cable adapter as
required:
Y/C : When connecting to a TV or VCR which
accepts Y/C signals and uses an S-Video
cable.
VCR
TV
CVBS : When connecting to a TV or VCR which does
not accept Y/C signals and uses an audio/video
cable.
To choose whether or not the following displays
appear on the connectedTV . . .
• Date/Time
* When connecting the cables, open this cover.
** Connect when an S-Video cable is not used.
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in
the Menu Screen (੬ pg. 50).
Or, press DISPLAY on the remote control
(provided) to turn on/off the date indication.
• Time Code
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 50).
• Playback Sound Mode, Tape Speed And Tape
Running Displays
..... set “ON SCREEN” to “LCD” or “LCD/TV” in the
Menu Screen (੬ pg. 50).
EN 53
Dubbing To Or From A Video Unit Equipped
With A DV Connector (Digital Dubbing)
It is also possible to copy recorded scenes from this
camcorder onto another video unit equipped with a
DV connector. Since a digital signal is sent, there is
little if any image or sound deterioration.
VIDEO/MEMORY Switch
(GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365 only)
[To use this camcorder as a player]
1
Make sure all units are turned off. Connect this
camcorder to a video unit equipped with a DV input
connector using a DV cable as shown in the
illustration.
To DV
Lock Button
2
Set this camcorder’s VIDEO/MEMORY Switch to
“VIDEO” (GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only), then the Power
Switch to “PLAY” while pressing down the Lock
Button located on the switch, turn on the video unit’s
power, and insert the appropriate cassettes in this
camcorder and the video unit.
MANUAL
AUTO
Core filter
OFF
PLAY
DV cable
(optional)
Power Switch
3
4
to play back the source tape.
4 Press
While watching the playback on the monitor,
engage the DV connector-equipped video unit’s
record mode from the spot on the source tape you
want to begin recording.
Core filter
To DV
IN/OUT
NOTES:
Video unit equipped
with DV connector
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● If the remote control is used when both the player and
recorder are JVC video units, both units will perform the
same operation. To prevent this from happening, press
the buttons on both units.
● If a blank portion or disturbed image is played back on
the player during dubbing, the dubbing may stop so that
an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 4. If this
occurs, turn off the power and make connections again.
● If “Playback Zoom” (੬ pg. 57), “Playback Special
Effects” (੬ pg. 56) or “Snapshot” is attempted during
playback, only the original playback image recorded on
the tape is output from the DV connector.
● When using a DV cable, be sure to use the optional
JVC VC-VDV204U DV cable.
For GR-DVL867/DVL767/DVL567/DVL367/DVL167 Owners:
[To Use This Camcorder As A Recorder]
1. Set this camcorder’s VIDEO/MEMORY Switch to “VIDEO” (GR-DVL867/DVL767/DVL567/DVL367 only),
then the Power Switch to “PLAY” while pressing down the Lock Button located on the switch.
2. Set “REC MODE” to “SP” or “LP” in the Menu Screen (੬ pg. 50).
3. Connect the DV cable as shown in the illustration and load a cassette to record on.
4. Press the Recording Start/Stop button to engage the Record-Pause mode. “
” appears on the screen.
DV. IN
5. Press the Recording Start/Stop button to start recording.
rotates.
6. Press the Recording Start/Stop button again to engage the Record-Pause mode.
stops rotating.
NOTES:
● Digital Dubbing is performed in the sound mode recorded on the original tape, regardless of the current “SOUND
MODE” setting (੬ pg. 47).
● During Digital Dubbing, no signals are output from the video or audio connectors.
54 EN
USING THE REMOTE CONTROL UNIT
The Full-Function Remote Control Unit can operate
this camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward and
Rewind) of your VCR. It also makes additional
playback functions possible.
1
3
Tab
Installing The Batteries
The remote control uses two “AAA (R03)” size
batteries. See “General Battery Precautions”
(੬ pg. 75).
2
+
1Remove the battery compartment cover while
–
–
pushing up the tab as illustrated.
+
2
Insert two ”AAA (R03)” size batteries in the
correct direction.
3
Re-attach the battery compartment cover.
Remote sensor
When using the remote control, be sure to point it at the remote
sensor. The transmitted beam’s approximate effective distance for
indoor use is 5m.
The transmitted beam may not be effective or may cause incorrect
operation outdoors or when the remote sensor is directly exposed
to sunlight or powerful lighting.
EN 55
Functions
With the camcorder’s Power
With the camcorder’s Power Switch
set to “PLAY”.
Buttons
Switch set to the camera
AUTO
MANUAL
”).
position (“
” or “
Infrared beam transmitting window Transmits the beam signal.
Zoom (T/W) Buttons
DISPLAY Button
SHIFT Button
Zoom in/out (੬ pg. 18)
Zoom in/out (੬ pg. 57)
੬ pg. 23, 50, 59
੬ pg. 57, 58
—
—
SLOW Rewind/Forward Buttons
Left/Right Buttons
—
—
੬ pg. 56
੬ pg. 57
REW Button
—
•Rewind/Reverse Shuttle Search on the
tape (੬ pg. 21)
•Displays previous page/file on the
memory card* (੬ pg. 28)
FADE/WIPE Button
EFFECT ON/OFF Button
EFFECT Button
—
—
—
—
੬ pg. 60
੬ pg. 56
੬ pg. 56
੬ pg. 59
PAUSE IN Connector
START/STOP Button
MBR SET Button
Functions the same as the Recording Start/Stop Button on the camcorder.
੬ pg. 58
Functions the same as SNAPSHOT on the camcorder.
—
SNAPSHOT Button
Up Button
INSERT Button
—
—
੬ pg. 57
੬ pg. 64
Down Button
A. DUB Button
—
—
੬ pg. 57
੬ pg. 63
PLAY Button
—
•Starts Playback of the tape (੬ pg. 21)
•Starts Auto Playback of the memory
card* (੬ pg. 28)
FF Button
—
•Forward/Forward Shuttle Search on the
tape (੬ pg. 21)
•Displays next page/file on the memory
card* (੬ pg. 28)
STOP Button
—
•Stops the tape (੬ pg. 21)
•Stops Auto Playback* (੬ pg. 28)
PAUSE Button
—
—
Pauses the tape (੬ pg. 56)
R.A.EDIT Buttons
੬ pg. 58 – 62
* GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only.
56 EN
USING THE REMOTE CONTROL UNIT (cont.)
Remote sensor
FEATURE: Slow-Motion Playback
PURPOSE:
To allow slow-speed search in either direction
during tape playback.
OPERATION:
1) To change from normal to Slow-Motion
Playback, press SLOW (9 or 0) more than
approx. 2 seconds. After approx. 1 minute in
Slow Rewind or approx. 2 minutes in Slow
Forward, normal playback resumes.
Ⅲ To stop Slow-Motion Playback, press PLAY (4).
NOTES:
● You can also engage Slow-Motion Playback from
Still Playback by pressing SLOW more than approx.
2 seconds.
● During Slow-Motion Playback, due to digital image
processing, the picture may take on a mosaic effect.
● After SLOW (9 or 0) is pressed and held, the still
image may be displayed for a few seconds, followed
by a blue screen for a few seconds. This is not a
malfunction.
SLOW
SLOW
Rewind Button
Forward Button
PLAY
● There may be a small margin between the slow-
motion playback start point you chose and the
actual start point for Slow-Motion Playback.
● During Slow-Motion Playback, there will be
disturbances in video and the picture may seem
unstable, especially with steady images. This is not
a malfunction.
EFFECT
ON/OFF
PAUSE
EFFECT
● During Slow-Motion Playback, press PAUSE (6) to
pause playback.
PLAYBACK EFFECT
OFF
PLAYBACK EFFECT
Select Menu
FEATURE: Frame-By-Frame Playback
PURPOSE:
To allow frame-by-frame search during tape
playback.
1
2
3
4
CLASS I C F I LM
MONOTONE
SEP I A
STROBE
OPERATION:
1) To change from normal to Frame-By-Frame
Playback, press SLOW (0) repeatedly for forward
or SLOW (9) repeatedly for reverse. Each time it
is pressed, the frame is played back.
NOTE:
You can also engage Frame-By-Frame Playback from
Still Playback by pressing SLOW (9 or 0) repeatedly.
FEATURE: Playback Special Effects
PURPOSE:
To allow you to add creative effects to the playback image.
OPERATION:
1) To start playback, press PLAY (4).
2) Point the remote control at the camcorder's remote sensor and press EFFECT. The PLAYBACK EFFECT
Select Menu appears.
3) Move the highlight bar to the desired effect by pressing EFFECT. The selected function is activated and
after 2 seconds the menu disappears.
Ⅲ To deactivate the selected effect, press EFFECT ON/OFF on the remote control. Pressing it again re-
activates the selected effect.
Ⅲ To change the selected effect, repeat from step 2 above.
NOTE:
The effects that can be used during playback are Classic Film, Monotone, Sepia and Strobe. The effects work the
same in playback as they did in recording. Refer to page 39 for more information.
EN 57
Remote sensor
FEATURE: Playback Zoom
PURPOSE:
To magnify the recorded image up to 50X at any
time during playback.
OPERATION:
1) Press PLAY (4) to find the scene of interest.
2) Press the Zoom Buttons (T/W) on the remote
control. Make sure the remote control is pointed
at the camcorder's remote sensor. Pressing T
zooms in.
3) You can move the image on screen around to
find a particular portion of the picture. While
holding down SHIFT, press
(Left),
(Right), (Up) and (Down).
Ⅲ To end zoom, press and hold W until magnifica-
tion returns to normal. Or, press STOP (5) and
then press PLAY (4).
Zoom Buttons
Up Button
SHIFT
NOTES:
Left Button
Down Button
● Zoom can also be used during slow-motion and still
playback.
● Due to ditital image processing, the quality of the
PLAY
STOP
Right Button
image may suffer.
Normal playback
To move image, press
(Right) while keeping
SHIFT held down.
Press T
58 EN
USING THE REMOTE CONTROL UNIT (cont.)
Random Assemble Editing [R.A.Edit]
Create edited videos easily using your camcorder as
the source player.You can select up to 8 “cuts” for
automatic editing, in any order you like. R.A.Edit is
more easily performed when the MBR (Multi-Brand
Remote) is set to operate with your brand of VCR
(see VCR CODE LIST), but can also be performed by
operating the VCR manually.
VCR (Recording deck)
Before operation, make sure the batteries are
installed in the remote control (੬ pg. 54).
SET REMOTE/VCR CODE
SHIFT
MBR SET
1
Turn off the power to the VCR and point the
remote towards the VCR’s infrared sensor. Then,
referring to the VCR CODE LIST, press and hold
MBR SET, and enter the brand code.
The code is automatically set once you release MBR
SET, and the VCR’s power comes on.
2
Make sure the VCR’s power is on. Then, while
holding SHIFT, press the button on the remote for the
desired function.The functions the remote can control
are PLAY, STOP, PAUSE, FF, REW and VCR REC
STBY (you do not need to press SHIFT for this one).
You are now ready to try Random Assemble
Editing.
VCR CODE LIST
VCR BRAND
NAME
BRAND
CODE
VCR BRAND
NAME
BRAND
CODE
IMPORTANT
Although the MBR is compatible with JVC VCRs
and those of many other makers, it may not work
with yours or may offer limited functions.
AKAI
PHILIPS
BLAUPUNKT
DAEWOO
NOTES:
● If the VCR’s power does not come on in step 1, try
another code from the VCR CODE LIST.
● Some brands of VCR do not come on automatically. In
this case, turn the power on manually and try step 2.
● If the remote control is not able to control the VCR, use
the controls on the VCR.
FERGUSON
SAMSUNG
SANYO
GRUNDIG
HITACHI
● When the remote control’s batteries run out, the VCR
brand you have set will be erased.
In that case, replace the old battery with a new one to
reset the VCR brand.
SELECO,
REX
JVC
A
B
C
SHARP
SONY
LG/GOLDSTAR
MITSUBISHI
THOMSON,
TELEFUNKEN,
SABA,
NEC
PANASONIC
NORDMENDE
TOSHIBA
EN 59
Connector cover**
MAKE CONNECTIONS
Also refer to pg. 22 and 23.
1
A JVC VCR equipped with a remote
pause connector . . .
..... connect the editing cable to the Remote PAUSE
connector.
A JVC VCR not equipped with a remote
pause connector but equipped with an
R.A.EDIT connector . . .
..... connect the editing cable to the R.A.EDIT
connector.
To JLIP***
or EDIT***
To S-VIDEO
To AV
A VCR other than above . . .
..... connect the editing cable to the remote control’s
2 PAUSE IN connector.
Insert a recorded tape into the camcorder. Set the
Audio/Video cable
(provided)
S-Video cable
(optional)
VIDEO/MEMORY Switch to “VIDEO” (GR-DVL867/
DVL865/DVL767/DVL765/DVL567/DVL367/DVL365
only), then set the Power Switch to “PLAY” while
pressing down the Lock Button located on the switch.
Editing cable
(provided)
To AUDIO,
VIDEO*
3
Turn the VCR power on, insert a recordable tape
and
-IN
and engage the AUX mode (refer to the VCR’s
connectors
instructions).
If your VCR has the
SCART connector,
use the provided
cable adapter.
NOTES:
● Before Random Assemble Editing, make sure the
indications do not appear on the TV monitor. If they do,
they will be recorded onto the new tape.
“Y/C”/“CVBS”
video out
select switch
To choose whether or not the following displays
appear on the connected TV . . .
• Date/Time
To Remote
PAUSE or R.A.EDIT
VCR
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in the
Menu Screen (੬ pg. 50).
Or, press DISPLAY on the remote control
(provided) to turn on/off the date indication.
• Time Code
To PAUSE IN
DISPLAY
TV
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 50).
• Playback Sound Mode, Tape Speed And Tape Running
Displays
..... set “ON SCREEN” to “LCD” or “LCD/TV” in the Menu
Screen (੬ pg. 50).
● Set the video out select switch of the cable adapter as
required:
Y/C : When connecting to a TV or VCR which
accepts Y/C signals and uses an S-Video
cable.
CVBS : When connecting to a TV or VCR which does
not accept Y/C signals and uses an audio/video
cable.
*
Connect when an S-Video cable is not used.
** When connecting cables, open this cover.
*** JLIP : GR-DVL167/DVL160
EDIT : GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365
● When editing on a VCR equipped with a DV input
connector, an optional DV cable can be connected
instead of an S-Video cable and audio/video cable.
For GR-DVL167/DVL160 Owners:
ATTENTION FOR EDITING CABLE
Make sure you connect the end with the core
filter (plug which has 3 rings around the pin) to
the camcorder.
60EN
USING THE REMOTE CONTROL UNIT (cont.)
SELECT SCENES
Programme
4
Point the remote control at the camcorder’s
I N
OUT
MODE
Random Assemble
Editing Menu
1
2
3
4
5
6
7
8
– –
– – : – –
~
~
~
~
~
~
~
~
remote sensor. Press PLAY (4) and then press
R.A.EDIT ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
5
If using a Fade/Wipe at the beginning of the
scene, press FADE/WIPE on the remote control.
• Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
T I ME CODE
TOTAL
– –
:
– –
00 : 00
6
At the beginning of the scene, press EDIT IN/
OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
Remote sensor
7
At the end of the scene, press EDIT IN/OUT. The
Edit-Out position appears in the Random Assemble
Editing Menu.
8
If using a Fade/Wipe at the end of the scene,
press FADE/WIPE.
• Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
• If you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
• When you use Fade/Wipe effects, that time is
included in the total time.
9
If using Playback Special Effects, press EFFECT
(੬ pg. 56).
10 Repeat steps 6 through 9 to register additional
• To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
REW
PLAY
FF
scenes.
FADE/WIPE
EFFECT
R.A.EDIT
ON/OFF
EDIT IN/OUT
• If you are not using Fade/Wipe or Programme AE
with special effects, repeat steps 6 and 7 only.
CANCEL
NOTES:
● When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between them.
● If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be cancelled and
editing will not take place.
● If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in the edited
version.
● Since time codes register time only as accurately as seconds, the time code total time may not match the total
programme time exactly.
● Turning off the camcorder’s power erases all registered Edit-In and Edit-Out points.
● If you select Sepia or Monotone mode from Programme AE with special effects, you cannot use the Black & White
Fader. In this case the Black & White indicator begins blinking. Once the next Edit-In point is registered, the effect is
turned off. To combine these effects, use Sepia or Monotone during recording, then use the Black & White Fader
during Random Assemble Editing.
● It is not possible to use Fade/Wipe effects and Programme AE with special effects during Random Assemble Editing
using a DV cable.
EN 61
AUTOMATIC EDITING TO VCR
11 Rewind the tape in the camcorder to the
beginning of the scene you want to edit and press
PAUSE (6).
12 Point the remote control towards the VCR’s
remote sensor and press VCR REC STBY (q6), or
manually engage the VCR’s Record-Pause mode.
13 Press the Recording Start/Stop Button on the
camcorder. Editing proceeds as programmed, right
through to the end of the last registered scene.
• When dubbing is complete, the camcorder enters
the Pause mode, and the VCR enters its Record-
Pause mode.
• If you do not register an Edit-Out point, the tape will
be dubbed all the way to the end automatically.
• If you operate the camcorder during automatic
editing, the VCR will enter its Record-Pause mode
and automatic editing will stop.
Recording Start/Stop Button
I N
OUT
MODE
Random Assemble
Editing Menu
1
2
3
4
5
6
7
8
00 : 25
07 : 18
03 : 33
09 : 30
15 : 55
~
~
~
~
~
~
~
~
02 : 05 – – – –
08 : 31 – – – –
05 : 53
– –
– –
13 : 15
16 : 29 – – – –
– –
– – – –
:
T I ME CODE
TOTAL
1 6
:
3 0
14 Engage the Stop modes for the camcorder and
9 : 39
the VCR.
To make the R.A.Edit counter display disappear,
press R.A.EDIT ON/OFF on the remote control.
Remote Sensor
NOTES:
● Pressing R.A.EDIT ON/OFF on the remote control
clears all settings registered during Random Assemble
Editing.
● When the editing cable is connected to the remote
control’s Pause In connector during dubbing, make sure
the remote control is pointed at the VCR’s sensor, and
the path between the two is unobstructed.
● Random Assemble Editing may not function properly
when using a tape including several duplicated time
codes (੬ pg. 20).
CONTINUED ON NEXT PAGE
PAUSE
R.A.EDIT
ON/OFF
VCR REC STBY
62EN
USING THE REMOTE CONTROL UNIT (cont.)
Programme 1
For More Accurate Editing
Some VCRs make the transition from Record-Pause
to Record mode faster than others. Even if you begin
editing for the camcorder and the VCR at exactly the
same time, you may lose scenes you wanted, or find
that you have recorded scenes you did not want. For
a cleanly edited tape, confirm and adjust the timing of
the camcorder against your VCR.
I N
OUT
MODE
Random Assemble
Editing Menu
1
2
3
4
5
6
7
8
– –
– – : – –
~
~
~
~
~
~
~
~
T I ME CODE
TOTAL
– –
:
– –
00 : 00
DIAGNOSING VCR/CAMCORDER TIMING
VIDEO Menu
1
Play back the tape in the camcorder, then point
the remote control at the camcorder’s remote sensor
and press R.A.EDIT ON/OFF.
SYNCHRO
–
O . 1
The Random Assemble Editing Menu appears.
2
Perform Random Assemble Editing on Pro-
gramme 1 only. In order to check VCR and
camcorder timing, select the beginning of a scene
transition as your Edit-In point.
3
Play back the dubbed scene.
Remote sensor
• If any images from the scene prior to the transition
you chose for your Edit-In point were recorded, that
means your VCR moves too quickly from Record-
Pause to Record mode.
• If the scene you tried to dub starts in progress, the
VCR is slow to start recording.
ADJUSTMENT OF VCR/CAMCORDER TIMING
4
Point the remote control at the camcorder’s
remote sensor and press R.A.EDIT ON/OFF to make
the Random Assemble Editing menu disappear, then
press the MENU/BRIGHT wheel in. The Menu
Screen appears.
5
Rotate the MENU/BRIGHT wheel to select “
VIDEO” and press it. The VIDEO Menu appears.
Then, rotate it to “SYNCHRO” and press it. The value
for “SYNCHRO” is highlighted.
6
Based on the diagnostics performed, you can
now advance the VCR’s record timing by rotating the
MENU/BRIGHT wheel towards “+”.You can also
delay the VCR’s record timing by rotating the MENU/
BRIGHT wheel towards “–”. The adjustment range is
from –1.3 to +1.3 seconds, in 0.1-second increments.
Press the MENU/BRIGHT wheel in to finish the
setting.
R.A.EDIT
ON/OFF
7
Rotate the MENU/BRIGHT wheel to select
RETURN” and press it twice.
Now perform Random Assemble Editing beginning
“
with step 4 on page 60.
NOTES:
● Before performing actual Random Assemble Editing, do
a few Random Assemble Editing trial runs to check
whether the value you have input is appropriate or not,
and make adjustments accordingly.
● Depending on the recorder, there may be situations
where the timing difference cannot be fully corrected.
EN 63
Display
Audio Dubbing
6e
Audio Dub
Standby mode
The audio track can be customized only when
recorded in the 12-bit mode (੬ pg. 47).
NOTES:
● Audio Dubbing is not possible on a tape recorded in 16-
bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
● To perform Audio Dubbing while watching on the
television, make connections (੬ pg. 22).
Power Switch
1
Play back the tape to locate the point where
editing will start, then press PAUSE (6).
2
While holding A.DUB (e) on the remote control,
press PAUSE (6). “6e” appears.
3
Press PLAY (4) , then begin “narrating”.
Speak into the microphone.
• To pause dubbing, press PAUSE (6).
4
To end Audio Dubbing, press PAUSE (6), then
STOP (5).
Speaker
To hear the dubbed sound during playback . . .
..... set “12BIT MODE” to “SOUND 2” or “MIX” in the
Menu Screen (੬ pg. 50, 51).
Remote sensor
NOTES:
● Sound is not heard from the speaker during Audio
Dubbing.
● When editing onto a tape that was recorded at 12-bit,
the old and new soundtracks are recorded separately.
● If you dub onto a blank space on the tape, the sound
may be disrupted. Make sure you only edit recorded
areas.
● If feedback or howling occurs during TV playback, move
the camcorder’s microphone away from the TV, or turn
down the TV’s volume.
● If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
● During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit
audio or a blank portion, Audio Dubbing stops
(੬ pg. 85).
MIC (external
Stereo
microphone
microphone input)
connector (GR-DVL867/
DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365
only)
For GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 Owners:
● Audio dubbing is also possible using an optional
microphone connected to the MIC connector.
● While an optional microphone is connected, the built-in
microphone is disabled.
A.DUB
PLAY
PAUSE
STOP
64EN
USING THE REMOTE CONTROL UNIT (cont.)
Insert Editing
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in and
outpoints. The original audio remains unchanged.
NOTES:
● Before performing the following steps, make sure that
“TIME CODE” is set to “ON” in the Menu Screen
(੬ pg. 49, 51).
● Insert Editing is not possible on a tape recorded in the
LP mode or on a blank portion of a tape.
● To perform Insert Editing while watching in the
television, make connections (੬ pg. 22).
Power Switch
Lock Button
1
Play back the tape, locate the Edit-Out point and
press PAUSE (6). Confirm the time code at this point
(੬ pg. 49, 51).
Display
2
Press REW (2) until the Edit-In point is located,
then press PAUSE (6).
w
6
3
Press and hold INSERT (w) on the remote
control, then press PAUSE (6). “6w” and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
12 : 34
4
Press START/STOP to begin editing.
• Confirm the insert at the time code you checked in
step 1.
Remote sensor
• To pause editing, press START/STOP. Press it again
to resume editing.
5
To end Insert Editing, press START/STOP, then
STOP (5).
NOTES:
● Programme AE with special effects (੬ pg. 38, 39) can
be used to spice up the scenes being edited during
Insert Editing.
● During Insert Editing, the date and time information
changes.
● If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
● During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert
Edting stops (੬ pg. 86).
START/STOP
INSERT
PLAY
PAUSE
REW
STOP
EN 65
SYSTEM CONNECTIONS
[A] Using USB or PC connection cable
GR-DVL167/DVL160 only
PC connection cable
(provided with
GR-DVL167 only)
To
RS-232C
To PC
USB cable
(provided)
To USB
To USB
connector
PC
GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only
[B] Using DV cable
OR
Power Switch
Core filter
Core filter
To DV
To DV
DV cable (optional)
connector
PC with DV
connector
VIDEO/MEMORY
Switch (GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only;
open the LCD monitor to access this switch.)
NOTES:
Connection To A Personal Computer
● Refer to “SOFTWARE INSTALLATION AND USB (or
PC) CONNECTION GUIDE” for the installation of the
bundled software and drivers.
[A] Using USB or PC connection cable
This camcorder can transfer still images to a PC by
using the software (GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365/DVL167:
provided, GR-DVL160: optional software HS-
V16KITE).
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● Never connect the USB or PC connection cable and
the DV cable simultaneously to the camcorder.
Connect only the cable you wish to use to the
camcorder.
● If the PC connected to the camcorder via the USB
cable is not powered, the camcorder does not enter the
USB mode.
[B] Using DV cable
It is also possible to transfer still images to a PC with
a DV connector by using software equipped with the
PC or commercially available software.
● The date/time information cannot be captured into the
PC.
● Refer to the instruction manuals of the PC and
1
2 Make sure the camcorder and PC are turned off.
Connect the camcorder to your PC using the
Software.
appropriate cable as shown in the illustration.
● The still images can also be transferred to a PC with a
DV connector-equipped capture board.
● When using a DV cable, be sure to use the optional
JVC VC-VDV206U or VC-VDV204U DV cable
depending on the type of DV connector (4 or 6 pins)
on the PC, or use the DV cable provided with the
capture board.
3
For GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 Owners:
If you are using the USB connection, set the VIDEO/
MEMORY switch to “MEMORY”.
4
Turn the camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch and turn on the PC.
● The system may not work properly depending on the
PC or capture board you are using.
• Refer to the instruction manual of the software on
how to transfer a still image to the PC.
For GR-DVL867/DVL865/DVL767/DVL765/DVL567/
DVL367/DVL365 Owners:
5
When finished, turn off the PC first, then the
camcorder.
“ACCESSING FILES” appears on the LCD monitor
while the PC is accessing data in the camcorder or
the camcorder is transferring a file to the PC.
NEVER disconnect the USB cable while “AC-
CESSING FILES” is displayed on the LCD monitor
since this can result in product damage.
66EN
SYSTEM CONNECTIONS (cont.)
VIDEO/MEMORY Switch
(Open the LCD monitor
to access this switch.)
Using The Camcorder As A WebCam
(GR-DVL867/DVL865 only)
Power Switch
This camcorder can be used as a WebCam via USB
connection.
1
Make sure all necessary software (provided) are
installed in your PC and all units are turned off.
2
Connect the camcorder to your PC using the USB
cable.
3
Set the VIDEO/MEMORY Switch to “MEMORY”
and set the Power Switch to “
then turn on the PC.
AUTO
MANUAL
”,
” or “
• “Web CAMERA” appears on the screen.
• If the PC is not powered on, the camcorder does not
To USB
enter the Web Camera mode.
4
When finished, turn off the PC first, then the
camcorder. Disconnect the USB cable from the
camcorder and PC.
USB cable
(provided)
NOTES:
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● Use the provided software PIXELA ImageMixer to
capture video in real-time.
● You can also use the camcorder for webconference by
using Windows® Microsoft Netmeeting and signing up
for Microsoft Hotmail.
To USB
connector
● In the Web Camera mode, the following buttons cannot
be operated: E-MAIL, SNAPSHOT, the Recording
Start/Stop button.
Refer to the instruction manuals of the PC and
provided Software.
USB-equipped PC
Display
PC
Web CAMERA
EN 67
REFERENCES
REFERENCES
CONTENTS
DETAILS ............................................ 68
TROUBLESHOOTING ....................... 69 – 73
USER MAINTENANCE ............................. 74
CAUTIONS .................................. 75 – 77
SPECIFICATIONS ........................... 78 – 79
INDEX ....................................... 80 – 86
Controls, Connectors And Indicators ....... 80 – 81
Indications ................................... 82 – 86
TERMS ........................ 87 – Back Cover
68 EN
DETAILS
I T E M S
N O T E S
❍ Perform charging where the temperature is between 10°C and 35°C. 20°C to
25°C is the ideal temperature range for charging. If the environment is too
cold, charging may be incomplete.
➪ Power
(੬ pg. 8)
❍ Charging times are for a fully discharged battery pack.
❍ Charging time varies according to the ambient temperature and the status of
the battery pack.
❍ To avoid interference with reception, do not use the AC Adapter near a radio.
❍ Since the AC Adapter processes electricity internally, it becomes warm
during use. Be sure to use it only in well-ventilated areas.
❍ The following operation stops charging:
• Set the Power Switch to “PLAY”, “
AUTO
MANUAL
”.
” or “
• Disconnect the AC adapter from the camcorder.
• Unplug the AC adapter’s power cord from the AC outlet.
• Detach the battery from the camcorder.
❍ When you use the LCD monitor outdoors in direct sunlight, the LCD monitor
may be difficult to see. If this happens, use the viewfinder instead.
➪ TAPE
RECORDING
(੬ pg. 16, 17)
❍ The cassette holder cannot be opened unless a power supply is attached.
❍ There may be a delay after you open the cassette holder cover until the
cassette holder opens. Do not use force.
❍ Once the cassette holder is closed, it recedes automatically. Wait until it
recedes completely before closing the cassette holder cover.
❍ When the Recording Start/Stop button is pressed, it may take a few seconds
before actual recording starts. “
” starts rotating when the camcorder
actually starts recording.
❍ The time required to calculate and display the remaining tape length, and the
accuracy of the calculation, may vary according to the type of tape used.
❍ “TAPE END” appears when the tape reaches its end, and the power goes off
automatically if left in this condition for 5 minutes. “TAPE END” also appears
when a cassette at its end is loaded.
About Batteries
DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause
a fire or explosion.
WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short
circuit and possibly start a fire.
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a large power capacity. However, when one is exposed to cold
temperatures (below 10°C), its usage time becomes shorter and it may cease to function. If this happens, place
the battery pack in your pocket or other warm, protected place for a short time, then re-attach it to the camcorder.
As long as the battery pack itself is not cold, it should not affect performance.
(If you’re using a heating pad, make sure the battery pack does not come in direct contact with it.)
Lithium-ion is vulnerable in colder temperatures.
EN 69
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the
beginning.
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
No power is supplied.
• The power is not connected
properly.
• The battery is dead.
• Connect the AC Adapter securely
(੬ pg. 9).
• Replace the dead battery with a
fully charged one (੬ pg. 8, 9).
“SET DATE/TIME!” appears. • The date/time is not set.
• The built-in clock battery has run
• Set the date/time (੬ pg. 11).
• Consult your nearest JVC dealer
for replacement.
out and the previously set date/time
has been erased.
Recording cannot be
performed.
— For Tape Recording —
• The tape’s erase protection tab is
set to “SAVE”.
• The Power Switch is set to “PLAY”
or “OFF”.
• Set the tape’s erase protection tab
to “REC” (੬ pg. 12).
AUTO
• Set the Power Switch to “
” or
MANUAL
” (੬ pg. 17).
“
• Set the VIDEO/MEMORY Switch to
• The VIDEO/MEMORY Switch is set
“VIDEO”.
• Replace with new cassette
(੬ pg. 12).
to “MEMORY”.
• “TAPE END” appears.
• The cassette holder cover is open.
— For Memory Card Recording —
• The VIDEO/MEMORY Switch is set
to “VIDEO”.
• Close the cassette holder cover.
• Set the VIDEO/MEMORY Switch to
“MEMORY”.
There is no picture.
• The camcorder is not getting power, • Turn the camcorder’s power off and
or some other malfunction exists.
on again (੬ pg. 17).
The focus does not adjust
automatically.
• Focus is set to the Manual mode.
• The recording was done in a dark
place, or the contrast was low.
• The lens is dirty or covered with
condensation.
• Set Focus to the Auto mode
(੬ pg. 43).
• Clean the lens and check the focus
again (੬ pg. 74).
CONTINUED ON NEXT PAGE
70 EN
TROUBLESHOOTING (cont.)
CORRECTIVE ACTION
SYMPTOM
POSSIBLE CAUSES
The cassette will not load
properly.
• The cassette is in the wrong
position.
• The battery’s charge is low.
• Set it in the right position
(੬ pg. 12).
• Install a fully charged battery
(੬ pg. 8, 9).
The memory card will not
load properly.
• The memory card is in the wrong
position.
• Set it in the right position
(੬ pg. 14).
Snapshot mode cannot be
used.
• The Squeeze mode is selected.
• Disengage the Squeeze mode
(੬ pg. 48).
The colour of Snapshot
looks strange.
• The light source or the subject does • Find a white subject and compose
not include white. Or there are
various different light sources
behind the subject.
your shot so that it also appears in
the frame (੬ pg. 26, 42).
• Turn off Sepia and Monotone
(੬ pg. 38, 39).
• The Sepia or Monotone mode is
activated.
The image taken using
Snapshot is too dark.
• Shooting was performed under
backlit conditions.
• Press the BACKLIGHT Button
(੬ pg. 44).
The image taken using
Snapshot is too bright.
• The subject is too bright.
• Set “PROGRAMME AE” to
“SPOTLIGHT” in the Menu Screen
(੬ pg. 38).
Digital Zoom does not work. • 10X optical zoom is selected.
• The VIDEO/MEMORY Switch is set
to “MEMORY”.
• Set “ZOOM” to “40X” or “500X” in
the Menu Screen (੬ pg. 47).
• Set the VIDEO/MEMORY Switch to
“VIDEO” (੬ pg. 17, 18).
The Black & White Fader
does not work.
• The Sepia or Monotone mode is
activated.
• Turn off Sepia and Monotone
(੬ pg. 38, 40).
Even when Slow Shutter is
not selected, the image
looks like it is activated.
• When shooting in the dark, the unit • If you want the lighting to look
becomes highly sensitive to light
and the image takes on an effect
similar to Slow Shutter.
more natural, set GAIN UP to
“AGC” or “OFF” in the Menu
Screen (੬ pg. 47).
EN 71
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
White Balance cannot be
activated.
• The Sepia or Monotone mode is
activated.
• Turn off Sepia or Monotone before
setting White Balance (੬ pg. 39,
45).
When shooting a subject
illuminated by bright light,
vertical lines appear.
• This is a result of exceedingly high
contrast, and is not a malfunction.
————
When the screen is under
direct sunlight during
shooting, the screen
becomes red or black for an
instant.
• This is not a malfunction.
————
During recording, the date/
time does not appear.
• “DATE/TIME” is set to “OFF” in the
Menu Screen.
• Set “DATE/TIME” to “ON” in the
Menu Screen (੬ pg. 49).
Files stored on the memory • Files stored on the memory card
card cannot be deleted. are protected.
• Remove protection from the files
stored on the memory card and
delete them (੬ pg. 30, 31).
Time code does not appear. • “TIME CODE” is set to “OFF” in the • Set “TIME CODE” to “ON” in the
Menu Screen.
Menu Screen (੬ pg. 49, 50).
Images on the LCD monitor • In places subject to low tempera-
• Adjust the brightness and angle of
the LCD monitor (੬ pg. 16, 17).
appear dark or whitish.
ture, images become dark due to
the characteristics of the LCD
monitor. When this happens, the
displayed colours differ from those
that are actually recorded.This is
not a defect of the camcorder.
• When the LCD monitor's fluores-
cent light reaches the end of its
service life, images on the LCD
monitor become dark. Consult your
nearest JVC dealer.
CONTINUED ON NEXT PAGE
72 EN
TROUBLESHOOTING (cont.)
CORRECTIVE ACTION
SYMPTOM
POSSIBLE CAUSES
The rear of the LCD monitor • The light used to illuminate the LCD • Close the LCD monitor to turn it off
is hot.
monitor causes it to become hot.
or set the Power Switch to “OFF”,
and let the unit cool down.
The indicators and the
image colour on the LCD
monitor are not clear.
• This may occur when the surface or
the edge of the LCD monitor is
pressed.
————
The LCD monitor or
viewfinder indications blink.
• Certain Fade/Wipe effects, certain
modes of Programme AE with
special effects, “DIS” and other
functions that cannot be used
together are selected at the same
time.
• Re-read the sections covering
Fade/Wipe effects, Programme AE
with special effects and “DIS”
(੬ pg. 38 – 41, 47).
Coloured bright spots
appear all over the LCD
monitor or the viewfinder.
• The LCD monitor and the view-
finder are made with high-precision
technology. However, black spots or
bright spots of light (red, green or
blue) may appear constantly on the
LCD monitor or the viewfinder.
These spots are not recorded on
the tape. This is not due to any
defect of the unit. (Effective dots:
more than 99.99 %)
————
————
During recording, sound
cannot be heard.
• This is normal.
AUTO
Play, Rewind and Fast-
Forward functions do not
work.
• The Power Switch is set to “
”
”
• Set the Power Switch to “PLAY”
(੬ pg. 21).
MANUAL
or “
”.
AUTO
A memory card cannot be
played back.
• The Power Switch is set to “
• Set the Power Switch to “PLAY”
(੬ pg. 28).
MANUAL
or “
”.
• The VIDEO/MEMORY Switch is set • Set the VIDEO/MEMORY
to “VIDEO”.
Switch to “MEMORY”.
The LCD monitor image is
distorted.
• During playback of the unrecorded
portion, High-speed Search and still
playback, LCD monitor indications
appear distorted. This is not a
defect.
————
Images on the LCD monitor • The speaker volume is too great.
are jittery.
• Turn the speaker volume down
(੬ pg. 21).
Blocks of noise appear
during playback, or there is
no playback picture and the
screen becomes blue.
• Clean the video heads with an
optional cleaning cassette
(੬ pg. 76).
————
EN 73
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
The LCD monitor, the
viewfinder and the lens
have become dirty (ex.
fingerprints).
• Wipe them gently with soft cloth.
Wiping strongly can cause damage
(੬ pg. 74).
————
An unusual mark appears.
• Check the section of the manual
that explains LCD monitor/
viewfinder indications
————
(੬ pg. 82 – 86).
An error indication
(E01, E02 or E06) appears.
• A malfunction of some kind has
occurred. In this case the
camcorder’s functions become
unusable.
• Remove the power supply (battery
pack, etc.) and wait a few minutes
for the indication to clear. When it
does, you can resume using the
camcorder. If the indication
remains even though you repeat
the above two or three times,
please consult your nearest JVC
dealer. Do not eject the cassette.
This will cause damage to the tape.
An error indication
(E03 or E04) appears.
• A malfunction of some kind has
occurred. In this case the
camcorder’s functions become
unusable.
• Eject the cassette once and re-
insert it, then check if the indication
clears. When it does, you can
resume using the camcorder. If the
indication remains even though
you repeat the above two or three
times, please consult your nearest
JVC dealer.
The charger indicator on
the camcorder does not
light.
• The temperature of the battery is
extremely high/low.
• Charging is difficult in places
subject to extremely high/low
temperatures.
• To protect the battery, it is
recommended to charge it in
places with a temperature of 10°C
to 35°C (੬ pg. 75).
When the image is printed
from the printer, a black bar
appears at the bottom of
the screen.
• This is not a malfunction.
• By recording with “DIS” activated
(੬ pg. 47) this can be avoided.
When the camcorder is
connected via the DV
connector, the camcorder
does not operate.
• The DV cable was plugged/
unplugged with power turned on.
• Turn the camcorder’s power off
and on again, then operate it.
The memory card cannot
be removed from the
camcorder.
• Push in the memory card a few
more times (੬ pg. 14).
————
74 EN
After Use
USER MAINTENANCE
Cleaning The Camcorder
1
1
To clean the exterior, wipe gently with a soft cloth.
Put the cloth in diluted mild soap and wring it well to
wipe off heavy dirt. Then wipe again with a dry cloth.
2 Turn off the camcorder.
Slide and hold OPEN/EJECT in the direction of
the arrow, then pull the cassette holder cover open
until it locks. The cassette holder opens automatically.
Remove the cassette.
2
Press PUSH OPEN and open the LCD monitor.
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
3
Press “PUSH HERE” to close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
3
To clean the lens, blow it with a blower brush,
then wipe gently with lens cleaning paper.
4 To clean the viewfinder, raise it to the vertical
position. Open the viewfinder cleaning hatch in the
direction of the arrow
4
Tilt the viewfinder upward 1. Press BATT.
RELEASE 2 and remove the battery pack 3 .
.
5
Insert a lens blower or soft cloth into the gap at
the bottom of the viewfinder and clean the interior of
the viewfinder with it
.
6
Close the hatch. Tilt the viewfinder back to the
horizontal position.
NOTES:
● Avoid using strong cleaning agents such as benzine or
alcohol.
Remove.
● Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.
Cassette holder
● Mould may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth refer
to the cautions of each product.
OPEN/EJECT
Switch
Cassette holder cover
PUSH HERE
BATT. RELEASE Button
1
Hatch
Lens blower
3
2
EN 75
CAUTIONS
Video Light
Battery Packs
The supplied battery pack is a
DANGER
lithium-ion battery. Before using
the supplied battery pack or an
optional battery pack, be sure to
read the following cautions:
Ⅲ The video light can become extremely
hot. Do not touch it either while in
operation or soon after turning it off,
otherwise serious injury may result.
1. To avoid hazards . . .
... do not burn.
... do not short-circuit the terminals. When
transporting, make sure the provided battery cap
is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
Ⅲ Do not place the camcorder into the
Terminals
carrying case immediately after using the video
light, since it remains extremely hot for some time.
Ⅲ When operating, keep a distance of about 30 cm
between the video light and people or objects.
Ⅲ Do not use near flammable or explosive materials.
Ⅲ Do not place the camcorder in a cabinet or box
while the video light is in operation.
... do not expose the battery to temperatures
exceeding 60°C, as this may cause the battery
to overheat, explode or catch fire.
Ⅲ When using the video light, if you wish to install the
camcorder in a fixed position, attach it to a tripod,
etc. Do not affix it directly to a surface such as a
table top.
Ⅲ It is recommended that you consult your nearest
JVC dealer for replacing the video light.
... use only specified chargers.
2. To prevent damage and prolong service life . . .
... do not subject to unnecessary shock.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type battery—
cooler temperatures impede chemical reaction,
while warmer temperatures can prevent
complete charging.
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life.
... fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
General Battery Precautions
If the remote control is not functioning even if it is
being operated correctly, the batteries are exhausted.
Replace them with fresh ones.
Use only the following batteries: AAA (R03) size x 2
Please make note of the following rules for battery
use. When misused, the batteries can leak or
explode.
... remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
1. When replacing batteries, refer to page 54.
2. Do not use any different size of batteries from
those specified.
3. Be sure to install batteries in the correct direction.
4. Do not use rechargeable batteries.
5. Do not expose the batteries to excessive heat as
they can leak or explode.
NOTES:
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging ................ 10°C to 35°C
Operation ............... 0°C to 40°C
Storage .................. –10°C to 30°C
● Recharging time is based on room temperature of
20°C.
6. Do not dispose of the batteries in a fire.
7. Remove the batteries from the unit if it is to be
stored for an extended period to avoid battery
leakage which can cause malfunctions.
8. Do not recharge the provided batteries.
● The lower the temperature, the longer recharging takes.
Cassettes
To properly use and store your cassettes, be sure to
read the following cautions:
1. During use . . .
... make sure the cassette bears the Mini DV mark.
... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
76 EN
CAUTIONS (cont.)
2. Avoid using the unit . . .
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
... in places subject to extremely high (over 40°C)
extremely low (under 0°C) temperatures.
2. Store cassettes . . .
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
... vertically, in their original cases.
Memory Cards
3. DO NOT leave the unit . . .
... in places of over 50°C.
... in places where humidity is extremely low (below
35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
4. To protect the unit, DO NOT . . .
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright
objects for long periods.
... expose the lens to direct sunlight.
... carry it by holding the LCD monitor or the
viewfinder.
... swing it excessively when using the shoulder
strap or the grip.
To properly use and store your memory cards, be
sure to read the following cautions:
1. During use . . .
... make sure the memory card bears the SD or
MultiMediaCard mark.
... make sure the memory card is positioned
properly when inserting.
2. While the memory card is being accessed
(during recording, playback, deletion, initializa-
tion, etc.) . . .
... never unload the memory card and never turn
off the camcorder.
3. Store memory cards . . .
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
5. Dirty heads can cause the following problems:
LCD Monitor
1. To prevent damage to the LCD monitor,
DO NOT . . .
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on
the bottom.
2. To prolong service life . . .
• No picture during playback.
... avoid rubbing it with coarse cloth.
• Blocks of noise appear during playback.
• During recording or playback, the Head Clog
Warning indicator “ ” appears.
3. Be aware of the following phenomena for LCD
monitor use.
These are not malfunctions:
• While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
• If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
• Recording cannot be performed properly.
In such cases, use an optional cleaning cassette.
Insert it and play back. If the cassette is used more
than once consecutively, damage to the video
heads may result. After the camcorder plays back
for about 20 seconds, it stops automatically. Also
refer to the cleaning cassette’s instructions.
If, after using the cleaning cassette, the problems
still exist, consult your nearest JVC dealer.
Mechanical moving parts used to move the video
heads and video tape tend to become dirty and
worn out over time. In order to maintain a clear
picture at all times, periodic check-ups are
recommended after using the unit for about 1,000
hours. For periodic check-ups please consult your
nearest JVC dealer.
Main Unit
1. For safety, DO NOT . . .
... open the camcorder’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
... allow inflammables, water or metallic objects to
enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
EN 77
Serious malfunctioning
How to handle a CD-ROM
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
• Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or back
surface. If the CD-ROM gets dirty, gently wipe it with
a soft cloth outward from the centre hole using a
circular motion.
• Do not use conventional disc cleaners or cleaning
spray.
• Do not bend the CD-ROM or touch its mirror
surface.
The camcorder is a microcomputer-controlled
device. External noise and interference (from a
TV, a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Adapter, etc.) and
wait a few minutes and then re-connect it and
proceed as usual from the beginning.
• Do not store your CD-ROM in a dusty, hot or humid
environment. Keep it away from direct sunlight.
About moisture condensation . . .
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form
on the glass‘ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
78 EN
SPECIFICATIONS
Camcorder
General
Power supply
: DC 11.0 V
DC 7.2 V
(Using AC Adapter)
(Using battery pack)
Power consumption
LCD monitor off, viewfinder on
: Approx. 4.5 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 4.3 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
LCD monitor on, viewfinder off
Video light
: Approx. 5.7 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 5.3 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
: Approx. 2.8 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 3.5 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Dimensions (W x H x D)
: 79 mm x 89 mm x 184 mm
(GR-DVL867/DVL865/DVL767/DVL765)
79 mm x 89 mm x 167 mm
(GR-DVL567/DVL367/DVL365/DVL167/DVL160)
(with the LCD monitor closed and the viewfinder pushed down)
Weight
: Approx. 580 g
(GR-DVL867/DVL865)
Approx. 570 g
(GR-DVL767/DVL765/DVL567)
Approx. 560 g
(GR-DVL367/DVL365)
Approx. 550 g
(GR-DVL167/DVL160)
Operating temperature
Operating humidity
Storage temperature
Pickup
: 0°C to 40°C
: 35% to 80%
: –20°C to 50°C
: 1/3.8" CCD (GR-DVL867/DVL865/DVL767/DVL765)
1/4" CCD (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Lens
: F 1.8, f = 3.8 mm to 38 mm, 10:1 power zoom lens
(GR-DVL867/DVL865/DVL767/DVL765)
F 1.8, f = 3.6 mm to 36 mm, 10:1 power zoom lens
(GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Filter diameter
LCD monitor
: ø37 mm
: 3.5" diagonally measured, LCD panel/TFT active matrix system
(GR-DVL867/DVL865/DVL567)
2.5" diagonally measured, LCD panel/TFT active matrix system
(GR-DVL767/DVL765/DVL367/DVL365/DVL167/DVL160)
: Electronic viewfinder with 0.24" black/white LCD
: Monaural
Viewfinder
Speaker
Digital Video Camera
Format
Signal format
: DV format (SD mode)
: PAL standard
Recording/Playback format
: Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
(using 80 min. cassette)
: SP: 80 min.
LP: 120 min.
EN 79
Digital Still Camera Function (GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only)
Storage media
: SD Memory Card/MultiMediaCard
Compression system
: Still image : JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
Picture quality
: 3 modes (1280 X 960 pixels*, 1024 x 768 pixels, 640 x 480 pixels)
: 2 modes (FINE/STANDARD)
Approximate number of
storable images
: ੬ pg. 27.
* GR-DVL867/DVL865/DVL767/DVL765 only.
Connectors
S-Video
Output
: Y:1 V (p-p), 75 Ω, analogue
C:0.29 V (p-p), 75 Ω, analogue
AV
Video output
Audio output
DV
: 1 V (p-p), 75 Ω, analogue
: 300 mV (rms), 1 kΩ, analogue, stereo
Output
: 4-pin, IEEE 1394 compliant
: 4-pin, IEEE 1394 compliant
Input (GR-DVL867/DVL767/
DVL567/DVL367/DVL167 only)
USB (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365 only)
: 5-pin
PC (GR-DVL167/DVL160 only)
: ø2.5 mm, 3-pole
EDIT (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365 only)
: ø3.5 mm, 2-pole
JLIP (GR-DVL167/DVL160 only)
: ø3.5 mm, 4-pole
AC Adapter
: AC 110 V to 240 V`, 50 Hz/60 Hz
Power requirement
Output
: DC 11 V
, 1 A
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications
subject to change without notice.
80 EN
INDEX Controls, Connectors And Indicators
1
3
0
2 3 4 5
6
9
0 ! @ #
7
MANUAL
AUTO
8
9
OFF
PLAY
$
%
^ & *
( ) q
EN 81
• J Terminal [JLIP (Joint Level Interface Protocol)]
(GR-DVL167/DVL160 only) ................. ੬ pg. 59
You can also connect to a JLIP-compatible
camcorder or VCR to control it from the
computer using the optional Software
HS-V16KITE.
Controls
1 OPEN/EJECT Switch ............................ ੬ pg. 12
2 • Stop Button [5] .................................... ੬ pg. 21
• BACKLIGHT Button ............................. ੬ pg. 44
• Edit Connector [EDIT]
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ........... ੬ pg. 59
3 • Rewind Button [2] ............................. ੬ pg. 21
• NIGHT Button ...................................... ੬ pg. 38
4 Play/Pause Button [4/6] ....................... ੬ pg. 21
5 Fast-Forward Button [3] ..................... ੬ pg. 21
6 Monitor Open Button [PUSH OPEN] ..... ੬ pg. 16
7 Dioptre Adjustment Control.................... ੬ pg. 10
DC Input Connector ............................. ੬ pg. 8, 9
Digital Video Connector
[DV IN/OUT: GR-DVL867/DVL767/DVL567/
DVL367/DVL167, DV OUT: GR-DVL865/DVL765/
DVL365/DVL160] (i.Link*) ............... ੬ pg. 53, 65
* i.Link refers to the IEEE1394-1995 industry
specification and extensions thereof. The logo
is used for products compliant with the i.Link
standard.
8 Battery Release Button
[BATT. RELEASE] ................................... ੬ pg. 8
9 Recording Start/Stop Button .................. ੬ pg. 16
0 • MENU Wheel [+, –, PUSH] .................. ੬ pg. 46
• LCD Monitor BRIGHT (Brightness)
S-Video Output Connector
[S-VIDEO] .................................. ੬ pg. 22, 52, 59
Control [+, –] ........................................ ੬ pg. 16
! Snapshot Button
• PC Connector
[SNAPSHOT] ....................... ੬ pg. 26, 27, 32, 42
(GR-DVL167/DVL160 only) ................. ੬ pg. 65
• USB (Universal Serial Bus) Connector
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ..... ੬ pg. 65, 66
@ • Power Zoom Lever [T/W]..................... ੬ pg. 18
• Speaker Volume Control [VOL.] .......... ੬ pg. 21
# • FOCUS Button..................................... ੬ pg. 43
• BLANK Button ..................................... ੬ pg. 24
Indicators
$ Lock Button............................................ ੬ pg. 17
% Power Switch
0
Tally Lamp ....................................... ੬ pg. 16, 48
AUTO
MANUAL
, PLAY, OFF] ................. ੬ pg. 17
[
,
CHARGE Lamp ....................................... ੬ pg. 8
Side LED Indicator (GR-DVL867/DVL865/
DVL767/DVL765 only) ........................... ੬ pg. 49
^ INDEX Button
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 29
3
2
Power Lamp .................................... ੬ pg. 16, 17
& INFO Button
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 29
Other Parts
* VIDEO/MEMORY Switch [VIDEO, MEMORY]
(GR-DVL867/DVL865/DVL767/DVL765/
• Remote Sensor.................................... ੬ pg. 54
• Camera Sensor
Be careful not to cover this area, a sensor
necessary for shooting is built-in here.
DVL567/DVL367/DVL365 only) ............. ੬ pg. 17
( E-MAIL Button
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 33
Viewfinder .............................................. ੬ pg. 10
Video Light............................................. ੬ pg. 19
Stereo Microphone ................................ ੬ pg. 63
Viewfinder Cleaning Hatch .................... ੬ pg. 74
Shoulder Strap Eyelets .......................... ੬ pg. 10
Grip Strap .............................................. ੬ pg. 10
LCD Monitor .................................... ੬ pg. 16, 17
Speaker ................................................. ੬ pg. 21
Battery Pack Mount ................................. ੬ pg. 8
Stud Hole ............................................... ੬ pg. 10
Tripod Mounting Socket ......................... ੬ pg. 10
) SELECT Button
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 28
q Video Light Switch
[LIGHT OFF/AUTO/ON]......................... ੬ pg. 19
Connectors
The connectors
to
are located beneath a cover.
Audio/Video Output Connector
[AV] ............................................ ੬ pg. 22, 52, 59
External Stereo Microphone Input Connector
[MIC] (GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 63
MEMORY CARD Cover
(GR-DVL867/DVL865/DVL767/DVL765/
DVL567/DVL367/DVL365 only) ............. ੬ pg. 14
82 EN
INDEX Indications
LCD Monitor/Viewfinder Indications During Tape Recording Only
1 Displays the selected Fade/Wipe effect.
(੬ pg. 40, 41)
1
2
3 4 5 6
2 Appears when in the Squeeze or Cinema mode.
(੬ pg. 48)
3 Rotates while the tape is running.
4 Displays the recording mode (SP or LP).
(੬ pg. 13)
(੬ pg. 16)
(੬ pg. 16)
LP 50min
REC
5 Displays the tape remaining time.
w
6
6 • “REC” appears during recording.
• “PAUSE” appears during Record-Standby
mode.
(੬ pg. 16)
7 Appears when the wind cut mode is engaged to
SOUND 12B I T
15 : 55
cut down on noise created by wind. (੬ pg. 48)
8 Appears when the Insert Editing (w) or Insert
Editing Pause (6w) mode is engaged.(੬ pg. 64)
9 Displays the sound mode for approx. 5 seconds
after turning on the camcorder.
(੬ pg. 47)
0
9
8 7
0 Displays the Time Code.
(੬ pg. 20, 49)
LCD Monitor/Viewfinder Indications During Memory Card Recording Only
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only)
1 Displays the image size.
(੬ pg. 14)
2 Appears and blinks during shooting. (੬ pg. 26)
3 • Appears during shooting.
• Blinks when a memory card is not loaded.
(੬ pg. 26)
1
2 3 4 5
1024
4 Displays the picture quality.
15
There are 2 modes available: F (Fine) and
S (Standard) (in order of quality).
5 Displays the remaining number of shots that can
be stored. (੬ pg. 26)
(੬ pg. 14)
EN 83
LCD Monitor/Viewfinder Indications During Both Tape And Memory Card
Recording
8 9
1
40x W
T
PHOTO
0
!
2
3
4
5
3
6
BR I GHT
1 0 . 01 . 02
10 : 0 0
7
#
@
AUTO
1 Appears when the Power Switch is set to “
”.
6 Appears when the iris is locked.
(੬ pg. 44)
(੬ pg. 17)
7 Appears when Digital Image Stabiliser (“DIS”) is
2 •
: Appears when Night-Scope is engaged.
(੬ pg. 38)
: Appears when “GAIN UP” is set to
“AUTO” and the shutter speed is being
engaged. (੬ pg. 47)
8 Approximate zoom ratio: Appears during
•
zooming.
(੬ pg. 18)
9 Appears during zooming.
automatically adjusted.
3 Appears when the white balance is adjusted.
(੬ pg. 45)
(੬ pg. 47)
Zoom level indicator
(੬ pg. 18)
0 Appears when taking a Snapshot. (੬ pg. 26, 42)
! Displays the brightness of the LCD monitor.
4 • “ؓ” : Appears when the exposure is adjusted.
(੬ pg. 16)
(੬ pg. 44)
•
: Appears when backlight compensation is
@ Displays the date/time.
# Appears when the focus is adjusted manually.
(੬ pg. 43)
(੬ pg. 11)
used.
5 Displays the selected Programme AE with special
effects. (੬ pg. 38)
(੬ pg. 44)
84 EN
INDEX Indications (cont.)
LCD Monitor/Viewfinder Indications During Tape Playback
1 Displays the sound mode.
2 Displays the Blank Search mode.
3 Displays the tape speed.
(੬ pg. 50, 51)
(੬ pg. 24)
1
2
3
4
(੬ pg. 13)
4 Appears while a tape is running.
12B I T
L
/
SOUND
1
SP
4
6
4
: Playback
3
2
6
: Fast-Forward/Shuttle search
: Rewind/Shuttle search
: Pause
6
1
e
4
: Forward slow-motion
: Reverse slow-motion
: Audio Dubbing
BLANK SEARCH
VOLUME
6
6e : Audio Dubbing Pause
5 Displays the date/time.
(੬ pg. 50, 51)
2 5 . 12 . 02
10 : 0 0
6 • BRIGHT : Displays the brightness of the LCD
monitor. (੬ pg. 16)
• VOLUME : Displays the speaker volume.
(੬ pg. 21)
116 : 21 : 25
7
6
5
The level indicator moves.
7 Displays the time code.
(੬ pg. 50, 51)
LCD Monitor/Viewfinder Indications During Memory Card Playback
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only)
1 Displays the operation mode.
(੬ pg. 29)
2 Displays the brightness of the LCD monitor.
1
(੬ pg. 16)
The level indicator moves.
BR I GHT
2
EN 85
Warning Indications
Indications
Function
Displays the battery remaining power.
Remaining power level: high
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator
blinks.
When the battery power is exhausted, power turns off automatically.
Appears when no tape is loaded.
(੬ pg. 12)
Appears when the erase protection tab is set to “SAVE” while the Power Switch is
CHECK TAPE’S ERASE
PROTECTION TAB
MANUAL
AUTO
set to “
” or “
” and the VIDEO/MEMORY Switch (GR-DVL867/DVL865/
pg. 12)
DVL767/DVL765/DVL567/DVL367/DVL365 only) is set to “VIDEO”.
(੬
Appears if dirt is detected on the heads during recording or playback.
Use an optional cleaning cassette. (੬ pg. 76)
HEAD CLEANING
REQUIRED USE
CLEANING CASSETTE
Appears if condensation occurs. When this indication is displayed, wait more
than 1 hour until condensation disappears.
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
Appears if a tape is not loaded when the Recording Start/Stop Button or
AUTO
SNAPSHOT Button is pressed while the Power Switch is set to “
“
” or
TAPE!
MANUAL
” and the VIDEO/MEMORY Switch (GR-DVL867/DVL865/DVL767/
DVL765/DVL567/DVL367/DVL365 only) is set to “VIDEO”.
TAPE END
Appears when the tape ends during recording or playback.
(੬ pg. 68)
Appears if a tape in another format is loaded when the VIDEO/MEMORY Switch
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only) is set to “VIDEO”.
DIFFERENT
FORMATTED TAPE
● Appears when the date/time is not set.
● Appears when the built-in clock battery runs out and the previously set
(੬ pg. 11)
SET DATE/TIME!
date/time is erased. Consult your nearest JVC dealer for replacement.
LENS CAP
or
LENS COVER
Appears for 5 seconds after power is turned on if the lens cap is attached.
Appears if Audio Dubbing is attempted on a blank portion of a tape.
A. DUB ERROR!
(੬ pg. 63)
● Appears if Audio Dubbing is attempted on a tape recorded in the LP mode.
(੬ pg. 63)
A. DUB ERROR!
<CANNOT DUB
ON A LP RECORDED TAPE>
<CANNOT DUB
ON A 16BIT
RECORDING>
<CHECK TAPE’S ERASE
PROTECTION TAB>
● Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio.
(੬ pg. 63)
● Appears if A. DUB (e) on the remote control is pressed when the erase
protection tab is set to “SAVE”.
(੬ pg. 63)
CONTINUED ON NEXT PAGE
86 EN
INDEX Indications (cont.)
Indications
Function
Appears if Insert Editing is attempted on a blank portion of a tape.
(੬ pg. 64)
INSERT ERROR!
● Appears if Insert Editing is attempted on a tape recorded in the LP mode.
(੬ pg. 64)
INSERT ERROR!
<CANNOT EDIT
ON A LP RECORDED TAPE>
<CHECK TAPE’S ERASE
PROTECTION TAB>
● Appears if INSERT (w) on the remote control is pressed when the erase
protection tab is set to “SAVE”.
(੬ pg. 64)
Appears when the memory card’s memory is full and shooting is not
possible.
MEMORY IS FULL
COPYING FAILED
● Appears if dubbing of copyguarded signals is attempted while this
camcorder is being used as a recorder.
● Appears in the following cases when dubbing from a tape to a memory
card:
– when no memory card is loaded.
– when the memory card's memory is full.
– when the memory card is not formatted.
(੬ pg. 32, 33)
MEMORY CARD!
or
PLEASE INSERT CARD
Appears if there is no memory card loaded when you attempt to record on a
memory card or access data on a memory card.
Appears when there is a problem with a memory card and its memory is
corrupt, or it has not been initialised. Initialise the memory card. (੬ pg. 36)
PLEASE
FORMAT
Appears if there are no image files stored on the memory card when you
attempt memory card playback.
NO IMAGES STORED
Appears if there are no E-Mail Clip files stored on the memory card when you
NO E-MAIL CLIP STORED
attempt memory card playback.
(੬ pg. 33)
Appears when the camcorder does not recognize the loaded memory card.
Remove the memory card once and insert it again. Repeat these procedures
until no indication appears. If the indication still appears, the memory card is
corrupted.
CARD ERROR!
UNSUPPORTED FILES
Appears if a file in another format is selected.
● Appears when you attempt to record on a copy-protected SD Memory Card.
● Appears when you attempt Memory Card menu operation with a copy-
protected SD Memory Card loaded.
CHECK CARD’S WRITE
PROTECTION SWITCH
The error indications (E01, E02 or E06) show what type of malfunction has
occured. When an error indication appears, the camcorder turns off automati-
cally. Remove the power supply (battery, etc.) and wait a few minutes for the
indication to clear.When it does, you can resume using the camcorder. If the
indication remains, consult your nearest JVC dealer.
E01, E02 or E06
UNIT IN SAFEGUARD
MODE REMOVE AND
REATTACH BATTERY
The error indications (E03 or E04) show what type of malfunction has
occured.When an error indication appears, the camcorder turns off
automatically. Eject the cassette once and re-insert it, then check if the
indication clears. When it does, you can resume using the camcorder. If the
indication remains, consult your nearest JVC dealer.
E03 or E04
UNIT IN SAFEGUARD
MODE EJECT AND
REINSERT TAPE
EN 87
Terms
A
I
AC Adapter................................................ ੬ pg. 8, 9
Audio Dubbing ............................................ ੬ pg. 63
Auto Date .................................................... ੬ pg. 49
Auto Focus .................................................. ੬ pg. 43
Auto Playback ............................................. ੬ pg. 28
Auto Shut off ................................... ੬ pg. 16, 21, 27
Icons ................................................... ੬ pg. 47 – 49
Index Playback............................................ ੬ pg. 29
Index Screen ............................................... ੬ pg. 29
Initialise A Memory Card ............................. ੬ pg. 36
Insert Editing ............................................... ੬ pg. 64
Iris ............................................................... ੬ pg. 44
Iris Lock ....................................................... ੬ pg. 44
B
J
Backlight Compensation ............................. ੬ pg. 44
Battery Low ................................................. ੬ pg. 85
Battery Pack ........................................ ੬ pg. 8, 9, 75
Beep............................................................ ੬ pg. 48
Blank Search............................................... ੬ pg. 24
Brighten The LCD Monitor .......................... ੬ pg. 16
Journalistic Shooting ................................... ੬ pg. 17
L
LCD monitor/Viewfinder Indications .... ੬ pg. 82 – 86
Load A Tape ................................................ ੬ pg. 12
M
C
Manual Focus ............................................. ੬ pg. 43
Memory Card ........................................ ੬ pg. 14, 76
Menu Screen, CAMERA ............................. ੬ pg. 47
Menu Screen, DISPLAY ........................ ੬ pg. 49, 50
Menu Screen, DSC ............................... ੬ pg. 14, 49
Menu Screen, MANUAL........................ ੬ pg. 47, 48
Menu Screen, SYSTEM ...................... ੬ pg. 48 – 50
Menu Screen, VIDEO ................................. ੬ pg. 50
Monotone .................................................... ੬ pg. 39
Motor Drive Mode ....................................... ੬ pg. 42
MultiMediaCard ..................................... ੬ pg. 14, 76
Channels (Left/Right) .................................. ੬ pg. 51
Charge The Battery Pack .............................. ੬ pg. 8
Cinema ........................................................ ੬ pg. 48
Classic Film................................................. ੬ pg. 39
Clean The Camcorder ................................. ੬ pg. 74
Connections .......... ੬ pg. 8, 9, 22, 23, 52, 59, 65, 66
D
Darken The LCD Monitor ............................ ੬ pg. 16
Date/Time Display ............................... ੬ pg. 49 – 51
Date/Time Settings...................................... ੬ pg. 11
Deleting Files .............................................. ੬ pg. 31
Demonstration Mode ............................... ੬ pg. 6, 49
Digital Zoom .......................................... ੬ pg. 18, 47
DIS (Digital Image Stabiliser) ...................... ੬ pg. 47
Dioptre Adjustment...................................... ੬ pg. 10
DPOF (Digital Print Order Format) .............. ੬ pg. 34
Dubbing................................................. ੬ pg. 52, 53
N
Night-Scope ................................................ ੬ pg. 38
P
Picture Quality/Image Size.......................... ੬ pg. 14
Playback Special Effects ............................. ੬ pg. 56
Playback Zoom ........................................... ੬ pg. 57
Power Switch Position ................................ ੬ pg. 17
Programme AE With Special Effects ..... ੬ pg. 38, 39
Protecting Files ........................................... ੬ pg. 30
Provided Accessories .................................... ੬ pg. 5
E
E-Mail Clip Recording ................................. ੬ pg. 33
Erase Protection ......................................... ੬ pg. 12
Exposure Control ........................................ ੬ pg. 44
R
F
Random Assemble Editing .................. ੬ pg. 58 – 62
Record-Standby .......................................... ੬ pg. 16
Recording Mode.......................................... ੬ pg. 13
Remote Control ........................................... ੬ pg. 54
Reset........................................................... ੬ pg. 49
Rewind The Tape ........................................ ੬ pg. 21
Fade-In/Out ........................................... ੬ pg. 40, 41
Fast-Forward The Tape ............................... ੬ pg. 21
Frame-By-Frame Playback ................... ੬ pg. 21, 56
G
Gain Up ....................................................... ੬ pg. 47
Grip Adjustment .......................................... ੬ pg. 10
CONTINUED ON NEXT PAGE
S
T
SD Memory Card .................................. ੬ pg. 14, 76
Self-Recording ............................................ ੬ pg. 17
Sepia ........................................................... ੬ pg. 39
Set Remote Control/VCR Code .................. ੬ pg. 58
Shuttle Search ............................................ ੬ pg. 21
Shutter Speed ............................................. ੬ pg. 39
Slow-Motion Playback........................... ੬ pg. 21, 56
Slow Shutter ................................................ ੬ pg. 39
Snapshot ............................................... ੬ pg. 26, 42
Snapshot Mode ........................................... ੬ pg. 42
Snow ........................................................... ੬ pg. 39
Sound Mode .................................... ੬ pg. 47, 50, 51
Speaker Volume .......................................... ੬ pg. 21
Specifications ........................................ ੬ pg. 78, 79
Sports .......................................................... ੬ pg. 39
Spotlight ...................................................... ੬ pg. 39
Squeeze ...................................................... ੬ pg. 48
Still Playback............................................... ੬ pg. 21
Strobe ......................................................... ੬ pg. 39
Tally ............................................................. ੬ pg. 48
Tele Macro .................................................. ੬ pg. 48
Time Code..................................... ੬ pg. 20, 49 – 51
Tripod Mounting .......................................... ੬ pg. 10
Twilight ........................................................ ੬ pg. 39
U
Unload A Tape ............................................. ੬ pg. 12
V
VIDEO/MEMORY Switch Position .............. ੬ pg. 17
Video Light .................................................. ੬ pg. 19
W
WebCam ..................................................... ੬ pg. 66
White Balance ............................................. ੬ pg. 45
Wide Mode .................................................. ੬ pg. 48
Wind Cut ..................................................... ੬ pg. 48
Wipe In/Out ........................................... ੬ pg. 40, 41
Z
Zooming ...................................................... ੬ pg. 18
See previous page as well.
VICTOR COMPANY OF JAPAN, LIMITED
1P2ri0n1teHdOinV*JaUpNan*VP
EG
COPYRIGHT© 2002 VICTOR COMPANY OF JAPAN, LTD.
|