ELECTRONIC CASH REGISTER
TE-2200
TE-2400
DEALER'S MANUAL
Version 1.0 August 2005
Eu
CI
Di
U.K.
Canada
System configuration ........................................................................................11
Hardware configuration .............................................................................................. 11
General configuration ...................................................................................................................... 11
Hardware diagram ...........................................................................................................................12
Display .............................................................................................................................................13
Input/output connectors ...................................................................................................................13
Online configuration.................................................................................................... 14
Peripheral ports and their connectable devices...............................................................................14
IPL (Initial program loading)..............................................................................15
Memory map of the terminal....................................................................................... 15
System configuration and procedure ........................................................................ 15
Via COM1 port (to receive IPL data from PC)..................................................................................15
Via CF card (to send the IPL data to CF card).................................................................................16
Via CF card (to send the IPL data to register) .................................................................................16
Initialization ........................................................................................................17
Machine initialization procedure ................................................................................ 17
Flag clear operation..................................................................................................... 19
Init 2 operation ............................................................................................................. 19
Entering diag mode ..................................................................................................... 20
Password ...................................................................................................................... 20
Programming (General explanation) ................................................................21
Program sub mode (P1 thru P7 mode) ...................................................................... 21
Entering the program sub mode ......................................................................................................21
File allocation (Program 5) ................................................................................23
File allocation program ............................................................................................... 23
Programming procedure ..................................................................................................................23
Issuing program reading report of program 5 mode................................................ 27
Issuing procedure ............................................................................................................................27
Report sample .................................................................................................................................27
Key allocation (Program 4)................................................................................29
Key allocation program ............................................................................................... 29
Programming procedure ..................................................................................................................29
Configuration of the physical key layout................................................................... 30
Issuing program reading report of program 4 mode................................................ 32
Issuing procedure ............................................................................................................................32
Report sample .................................................................................................................................32
Key function/machine feature (Program 3) ......................................................33
General control program............................................................................................. 33
Programming procedure ..................................................................................................................33
Program data (by address code) .....................................................................................................33
Address code 01 (date order/password)................................................................................................... 33
Address code 02 (password) .................................................................................................................... 33
Address code 03 (consecutive number) ................................................................................................... 33
Address code 04 (tax system, rounding, etc.) .......................................................................................... 34
Address code 05 (print control for receipt)................................................................................................ 35
Address code 06 (calculation & operation control) ................................................................................... 36
Address code 07 (menu & price shift)....................................................................................................... 37
Address code 08 (print control for fixed total report)................................................................................. 38
Address code 09 (print control for fixed total report)................................................................................. 39
Address code 10 (print control for taxable amount, till timer) ................................................................... 40
Address code 13 (online control) .............................................................................................................. 40
Address code 14 (currency exchange control) ......................................................................................... 41
Address code 15 (print control for reports) ............................................................................................... 42
Address code 16 (print control for grand total) ......................................................................................... 43
TE-2200/2400 Dealer's Manual
3
Introduction & Contents
Address code 17 (print control)................................................................................................................. 44
Address code 18 (print control for guest receipt and slip) ........................................................................ 45
Address code 19 (order control) ............................................................................................................... 45
Address code 21 (message control) ......................................................................................................... 46
Address code 25 (condiment etc.) ............................................................................................................ 47
Address code 26 (check tracking) ............................................................................................................ 47
Address code 27 (clerk control) ................................................................................................................ 47
Address code 28 (Euro) ............................................................................................................................ 48
Address code 29 (Euro) ............................................................................................................................ 48
Address code 30 (Internal thermal printer control) ................................................................................... 49
Address code 32 (direct maintenance PLU) ............................................................................................. 49
Address code 31 (scanning) ..................................................................................................................... 49
Address code 33 (batch PLU maintenance) ............................................................................................. 50
Address code 34 (backlight control) ......................................................................................................... 50
Address code 36 (store/recall/auto new check number)........................................................................... 51
Address code 37 (check number) ............................................................................................................. 51
Department key/flat-PLU key/PLU program (Batch feature programming)............ 52
Programming procedure ..................................................................................................................52
Program data ...................................................................................................................................52
Department key/flat-PLU key/PLU program (Individual feature programming) ..... 54
Programming procedure ..................................................................................................................54
Program data (by address code) .....................................................................................................54
Transaction key program ............................................................................................ 57
Programming procedure ..................................................................................................................57
Program data ...................................................................................................................................57
Clerk program .............................................................................................................. 80
Secret number, drawer, check number programming......................................................................80
Clerk detail link programming ..........................................................................................................80
Clerk other programming .................................................................................................................81
Other programs............................................................................................................ 83
Time range programming ................................................................................................................83
Table range programming................................................................................................................83
Tax table programming ....................................................................................................................84
Set menu programming ...................................................................................................................89
Batch X/Z report programming ........................................................................................................89
Arrangement programming..............................................................................................................90
Check print control programming.....................................................................................................90
Mix & match programming...............................................................................................................91
Employee number programming .....................................................................................................92
Scheduler programming ..................................................................................................................93
Bottle link table programming ..........................................................................................................95
I/O parameter table programming....................................................................................................96
Printer connection table programming.............................................................................................97
Non PLU table programming ...........................................................................................................98
Scanning PLU maintenance programming ............................................................... 99
Batch maintenance PLU programming............................................................................................99
Activation of batch maintenance PLU..............................................................................................99
Scanning PLU direct maintenance programming ..........................................................................100
Scanning PLU individual programming..........................................................................................101
One touch NLU programming........................................................................................................103
Issuing program reading report of program 3 mode.............................................. 104
Issuing procedure ..........................................................................................................................104
Report sample ...............................................................................................................................104
Character (Program 2) .....................................................................................105
Programming descriptors ......................................................................................... 105
Programming procedure ................................................................................................................105
Programming data .........................................................................................................................105
4
Programming item/key descriptors.......................................................................... 114
Programming procedure ................................................................................................................ 114
Programming data ......................................................................................................................... 114
Programming item/clerk descriptors by range ....................................................... 116
Programming procedure ................................................................................................................ 116
Program data ................................................................................................................................. 116
Entering characters ................................................................................................... 117
By character keyboard................................................................................................................... 117
By character code.......................................................................................................................... 119
Character code list......................................................................................................................... 119
Editing characters ..................................................................................................... 120
Correcting a character just entered ...............................................................................................120
Correcting and adding a PLU descriptor already set .....................................................................120
Correcting a key descriptor already set .........................................................................................120
Correcting a message descriptor already set ................................................................................120
Issuing program reading report of program 2 mode.............................................. 121
Issuing procedure ..........................................................................................................................121
Report sample ...............................................................................................................................121
Unit price/rate (Program 1) ..............................................................................123
Date/time setting........................................................................................................ 123
Date setting....................................................................................................................................123
Time setting ...................................................................................................................................123
Unit price program..................................................................................................... 123
Programming procedure ................................................................................................................123
Rate program ............................................................................................................. 125
<Currency exchange> ...................................................................................................................125
<Check>, <New balance>, <Premium (%+)>, <Discount (%–)>, <Rate tax>................................125
Amount program........................................................................................................ 125
<Cash>, <Check>, <New balance>, <Plus (+)>, <Minus (–)>, <Coupon> ....................................125
Scanning PLU direct maintenance programming ..........................................................................125
Issuing program reading report of program 1 mode.............................................. 126
Issuing procedure ..........................................................................................................................126
Report sample ...............................................................................................................................126
Program reading (Program 6) .........................................................................127
Issuing program reading report ............................................................................... 127
Issuing procedure ..........................................................................................................................127
Report code ...................................................................................................................................127
Report sample............................................................................................................ 128
Fixed totalizer ................................................................................................................................128
Transaction key .............................................................................................................................128
PLU................................................................................................................................................129
Department ....................................................................................................................................130
Group.............................................................................................................................................130
Clerk ..............................................................................................................................................131
Hourly sales ...................................................................................................................................131
Scanning PLU................................................................................................................................131
Table analysis ................................................................................................................................132
Grand total .....................................................................................................................................132
General control ..............................................................................................................................132
Special character ...........................................................................................................................132
Report header................................................................................................................................133
Tax table ........................................................................................................................................133
Set menu table...............................................................................................................................133
Batch X/Z .......................................................................................................................................133
TE-2200/2400 Dealer's Manual
5
Introduction & Contents
Clerk detail link ..............................................................................................................................134
Receipt message ...........................................................................................................................134
Check endorsement.......................................................................................................................134
Slip/external printer message ........................................................................................................135
Arrangement table .........................................................................................................................135
Character recall .............................................................................................................................135
Non-PLU table ...............................................................................................................................135
Check print control........................................................................................................................135
Mix & match ...................................................................................................................................136
Employee.......................................................................................................................................136
Scheduler.......................................................................................................................................136
Bottle link table ..............................................................................................................................136
One touch NLU ..............................................................................................................................137
Help message................................................................................................................................137
Terminal connection table ..............................................................................................................137
Printer connection table .................................................................................................................137
AT command..................................................................................................................................138
Online password ............................................................................................................................138
I/O parameter table........................................................................................................................138
Miscellaneous message ................................................................................................................138
Printing guidance message ...........................................................................................................138
Error message ...............................................................................................................................139
Registration guidance message ....................................................................................................139
X/Z guidance message ..................................................................................................................139
Program guidance message..........................................................................................................139
Auto-program & system utilities (Program 7)...............................................141
Auto-programming .................................................................................................... 141
Auto-programming functions..........................................................................................................141
Auto-programming operation .........................................................................................................144
Other utilities..................................................................................................................................145
Manager operation ...........................................................................................149
Manager control mode (X1 mode)............................................................................ 149
Entering the manager control mode ..............................................................................................149
Assign drawers for each clerk........................................................................................................149
Stock quantity maintenance (PLU/flat PLU/scanning PLU)................................... 150
To add to the actual stock quantity of a PLU/flat PLU/scanning PLU ............................................150
To subtract from the actual stock quantity of a PLU/flat PLU/scanning PLU .................................150
To input the new stock quantity of a PLU/flat PLU .........................................................................151
Clerk assignment....................................................................................................... 151
To link clerk button/key to interrupt buffers ....................................................................................151
To link clerk secret numbers to interrupt buffers ............................................................................151
To link clerk numbers to clerk number keys ...................................................................................151
Programming for the Euro ........................................................................................ 152
Programming for the Australian GST ...................................................................... 154
Programming of items in the program 1 mode ....................................................... 154
To enter the program 1 mode ........................................................................................................154
To exit the program 1 mode ...........................................................................................................154
Read/reset report issuance .............................................................................155
Preparation for issuing report .................................................................................. 155
Money declaration .........................................................................................................................155
Password (X2/Z2 mode) ................................................................................................................155
Issuing read/reset report .......................................................................................... 155
Programmability .............................................................................................................................156
Issuing procedure ..........................................................................................................................156
6
Report sample ...............................................................................................................................160
Financial report ..............................................................................................................................160
Individual item/key report ...............................................................................................................160
Fixed total report............................................................................................................................161
Transaction key report ...................................................................................................................162
PLU report .....................................................................................................................................163
PLU stock report ............................................................................................................................164
Department report..........................................................................................................................165
Group report ..................................................................................................................................166
Clerk report ....................................................................................................................................167
Hourly sales report.........................................................................................................................168
Monthly report................................................................................................................................168
Table analysis report ......................................................................................................................169
Open check report .........................................................................................................................169
Scanning PLU report .....................................................................................................................170
Scanning PLU stock report ............................................................................................................172
Mix & match report.........................................................................................................................172
Time & attendance report ..............................................................................................................173
File reset ........................................................................................................................................173
Application systems ........................................................................................175
Scanning PLU ............................................................................................................ 175
System configuration of the scanning PLU system .......................................................................175
Setup .............................................................................................................................................175
Barcode system .............................................................................................................................175
PLU maintenance ..........................................................................................................................176
Scanning PLU registration .............................................................................................................177
Mix & match discount.....................................................................................................................179
Check tracking system.............................................................................................. 180
System configuration .....................................................................................................................180
Printing on the external printers .............................................................................. 181
System configuration of the external printer system......................................................................181
Backup system ..............................................................................................................................181
Printing control options for order....................................................................................................182
Time and attendance ................................................................................................. 182
Tips ....................................................................................................................183
Future order ............................................................................................................... 183
Usage ............................................................................................................................................183
Preparation ....................................................................................................................................183
Eat-in/takeout ............................................................................................................. 183
Automatic execution of Euro switchover by arrangement and scheduler ........... 184
Appendix: Calculation method .......................................................................185
Fixed total file............................................................................................................. 185
Appendix: Font code tables ............................................................................187
Standard font set (default) ........................................................................................ 187
Multilingual + Euro (Windows code page 858) ..............................................................................187
Special font set .......................................................................................................... 188
Slavic (Windows code page 852) ..................................................................................................188
Greek .............................................................................................................................................188
Cyrillic (Windows code page 866) .................................................................................................189
Baltic ..............................................................................................................................................189
Arabic.............................................................................................................................................190
TE-2200/2400 Dealer's Manual
7
Introduction & Contents
Appendix: Peripheral device configuration ...................................................191
UP-360......................................................................................................................... 191
SP-1300....................................................................................................................... 191
Quick scan 6000......................................................................................................... 192
Appendix: File record format ..........................................................................193
Fixed totalizer file ...................................................................................................... 193
Fixed totalizer (daily)......................................................................................................................193
Fixed totalizer (periodic/consolidation) ..........................................................................................193
Transaction key file ................................................................................................... 194
Transaction key (daily)...................................................................................................................194
Transaction key (periodic/consolidation) .......................................................................................194
PLU file ....................................................................................................................... 194
PLU (daily) .....................................................................................................................................194
PLU (periodic/consolidation)..........................................................................................................194
Department file .......................................................................................................... 195
Department (daily) .........................................................................................................................195
Department (periodic/consolidation) ..............................................................................................195
Group file.................................................................................................................... 195
Group (daily) ..................................................................................................................................195
Group (periodic/consolidation).......................................................................................................195
Clerk file...................................................................................................................... 196
Clerk (programming) ......................................................................................................................196
Clerk detail (daily, periodic/consolidation)......................................................................................196
Clerk detail link (program)..............................................................................................................196
Hourly sales file ......................................................................................................... 197
Hourly sales (daily) ........................................................................................................................197
Hourly sales (periodic/consolidation) ............................................................................................197
Monthly sales file....................................................................................................... 197
Monthly sales (daily, periodic/consolidation)..................................................................................197
Scanning PLU files .................................................................................................... 198
Scanning PLU file (daily) ...............................................................................................................198
Non PLU table file (program) .........................................................................................................198
Batch maintenance PLU file (program)..........................................................................................198
Direct maintenance PLU file (program) .........................................................................................198
One touch NLU table file................................................................................................................199
Mix & match table file ................................................................................................ 199
Mix & match table file (daily)..........................................................................................................199
Mix & match table file (periodic/consolidation)...............................................................................199
Bottle link table file.................................................................................................... 199
Bottle link table file (program) ........................................................................................................199
Table analysis file ...................................................................................................... 200
Table analysis (daily) .....................................................................................................................200
Table analysis (periodic/consolidation) ..........................................................................................200
Time and attendance file........................................................................................... 200
Time and attendance (daily) ..........................................................................................................200
Employee file .................................................................................................................................200
Grand total file ........................................................................................................... 201
Grand total (daily) ..........................................................................................................................201
Grand total (consolidation).............................................................................................................201
General control file .................................................................................................... 201
General control ..............................................................................................................................201
Special character file................................................................................................. 202
Special character ...........................................................................................................................202
8
Report header file ...................................................................................................... 202
Report header................................................................................................................................202
Tax table file ............................................................................................................... 202
Tax table ........................................................................................................................................202
Set menu table file ..................................................................................................... 202
Set menu table...............................................................................................................................202
Batch X/Z file .............................................................................................................. 203
Batch X/Z .......................................................................................................................................203
Receipt message file ................................................................................................. 203
Receipt message ...........................................................................................................................203
Check endorsement message file ............................................................................ 203
Check endorsement message .......................................................................................................203
Slip/external printer message file ............................................................................ 203
Slip/external printer message ........................................................................................................203
Arrangement file ........................................................................................................ 204
Arrangement file ............................................................................................................................204
Character recall file ................................................................................................... 204
Character recall .............................................................................................................................204
Check print file........................................................................................................... 204
Check print.....................................................................................................................................204
Scheduler file ............................................................................................................. 204
Scheduler.......................................................................................................................................204
System files................................................................................................................ 205
Character key table file ..................................................................................................................205
Key table file ..................................................................................................................................206
Terminal connection table file ........................................................................................................207
Printer connection table .................................................................................................................207
Operation start date file .................................................................................................................207
Initialize code file ...........................................................................................................................207
AT command file ............................................................................................................................208
Online password file ......................................................................................................................208
I/O parameter table file ..................................................................................................................208
System error log file .......................................................................................................................208
Graphic image files.................................................................................................... 208
Graphic logo file.............................................................................................................................208
Graphic logo file (for external printer) ............................................................................................208
Watermark print file........................................................................................................................208
Guidance message files............................................................................................ 209
Error message file..........................................................................................................................209
Miscellaneous message file...........................................................................................................213
Printing guidance message file......................................................................................................214
X/Z guidance message file ............................................................................................................216
Program guidance message file ....................................................................................................218
Registration guidance message file...............................................................................................221
Help message file ..........................................................................................................................222
Appendix: Compulsory....................................................................................227
Appendix: Error code.......................................................................................229
Index ..................................................................................................................233
TE-2200/2400 Dealer's Manual
9
Introduction & Contents
10
System configuration
Hardware configuration
General configuration
1Operator display
2Customer display (Popup display)
3Stroke keyboard (TE-2200)
4Touch keyboard (TE-2400)
5CF card slot cover
6Printer cover
7Mode switch
Sys
8Connector cover (opposite side)
2
6
2
6
1
1
8
8
7
7
3
5
4
5
TE-2200/2400 Dealer's Manual
11
System configuration
CF card
drawer
Hardware diagram
external printer
slip printer
multi drawer
scanner
Main Display
HHS-15
UP-360
SP-1300
Popup
display
Journal printer
Receipt printer
Power
supply
Flash
Memory
RAM
CPU
Popup
disp.
i/f
RS-
232C
COM1
RS-
232C
COM2
Drawer
Drawer
1
i/f
2
i/f
CF card
MODEM
or
Drawer
PC
Slip
External
printer
UP-360
printer
Drawer
Scanner
HHS-15
SP-1300
Power
supply
Power
supply
31AD-U/E
Note: Shadowed device and dot line indicate option devices.
12
Display
Contrast control (Except for U.S. model)
DATE/
TIME
RECEIPT
ON/OFF
HELP
LIGHT DARK
CONTRAST
Input/output connectors
Input /output connectors
Sys
COM ports are located in the leftside connector cover.
SCANNER
COM2
PC/MODEM
COM1
TE-2200/2400 Dealer's Manual
13
System configuration
Online configuration
Peripheral ports and their connectable devices
COM port
Drawer
port
Model
Device
COM1
COM2
MODEM/PC
✔
✔
External printer
(Max. 2 printers)
✔
✔
✔
TE-2200
TE-2400
Slip printer
Scanner
Drawer
1 (Max 2)
✔: can connect
Available device/cable list
External printer:
Printer cable:
Slip printer:
UP-360
PRT-CB-8A(3m) or PRT-CB-8B(5m)
SP-1300
Printer cable:
Power supply:
Scanner (Hand-held):
Scanner (LASER):
Scanner (Fixed)
MODEM:
PRT-CB-8C
AD31U or AD31E
HHS-15
PSC Quick Scan 6000
PSC HS1250
US Robotics 56K V.92 External Faxmodem/56K Faxmodem (U.S. only)
PRL-CB-2
PC cable:
Steps to define COM port/peripheral devices
After connecting peripheral devices, programming of I/O parameter table, printer connection table are necessary.
START
No
No
Connect a slip printer?
Connect Modem or PC?
Yes
Yes
Connect it to free COM1 or COM2 port.
Connect it to COM1 port.
No
No
Connect external printer(s)?
Connect a scanner?
Yes
Yes
Connect it (them) to free COM port(s).
Connect it to COM2 port.
END
14
IPL (Initial program loading)
IPL should be made before initializing when the application program has been modified.
Memory map of the terminal
The application programs are downloaded from PC (via COM port)/other terminal (via inline or COM port)/CF card to the
internal flash memory.
I
CF card
backup data
program data
RAM
totalizer/counter,
work area
Flash memory
Application program
Application program
5
ROM
IPL
bios, program loader
some diagnosis
System configuration and procedure
Via COM1 port (to receive IPL data from PC)
Operation
1. Set the mode switch to OFF position.
2. While holding down the <JOURNAL FEED>, turn the mode switch to PGM position.
3. Release <JOURNAL FEED> after the register shows “INIT”.
4. Enter “44449999” and press <SUBTOTAL>.
5. Enter “0” (communication speed: 38400 bps) and press <SUBTOTAL>.
6. Start the IPL program of the PC.
PC
COM1 port
TE-2200/2400 Dealer's Manual
15
IPL (Initial Program Loading)
Via CF card (to send the IPL data to CF card)
Operation
1. Set the mode switch to OFF position.
2. Open the CF card slot cover and insert the CF card securely.
(Please check that the CF card is vacant. Refer to the “System utility section in PGM7”.)
3. Turn the mode switch to PGM position.
4. Enter “7” and press <SUBTOTAL>.
5. Enter “170” and press <SUBTOTAL>.
6. Enter “49” and press <CASH>.
(In case of quitting, press <SUBTOTAL> instead of <CASH>.)
7. Turn OFF the register and pull out the CF card.
Via CF card (to send the IPL data to register)
Operation
CF card
1. Set the mode switch to OFF position.
2. Open the CF card slot door and insert the CF card securely.
3. While holding down the <JOURNAL FEED>, turn the mode switch to PGM position.
4. Release <JOURNAL FEED> after the register shows “INIT”.
5. Enter “44449999” and press <SUBTOTAL>.
6. Enter “20” and press <SUBTOTAL>.
Never plug/unplug the CF card during IPL.
16
Initialization
Machine initialization procedure
1. Plug the power cord into an AC outlet.
RECEIPT
FEED
2. Hold down <JOURNAL FEED>.
REG2 X1
I
REG1
OFF
RF
Z1
X2/Z2
3. Turn the mode switch to PGM position.
4. Release <JOURNAL FEED>.
PGM
You should see “0000000000” on the display.
If 10 zeros are not shown or another character are shown,
immediately set the mode switch to OFF and restart from
RECEIPT
FEED
JOURNAL
FEED
the beginning of this procedure.
5. Enter 11-digit program code from the worksheet.
D11D10D9D8 ~ D3D2D1 s
refer to Worksheet (Initialize)
6. Press <SUBTOTAL> to register the program code.
(Wait until beep twice.)
7. Press <SUBTOTAL> to register the program code.
TE-2200/2400 Dealer's Manual
17
Initialization
Worksheet (Initialize)
Description
Choice
Program code
Yes = 0
No = 4
:
Print password of PGM mode, when flag clear operation is performed.
D11
Significant
numbers
: : : :
Password in PGM3 ~ 7 mode
D10 D9 D8 D7
Significant
number
Messages and descriptors are written in
English = 0, French = 1, Spanish = 2, German = 4
:
D6
Model for
Significant
number
U.S. or Canada (Date order: month/day/year)
Other area (~00, Date order: day/month/year) = 1,
Other area (0, Date order: day/month/year)
= 2,
:
D5
= 3
Fixed value:
TE-2200: 25
TE-2400: 04
Significant
numbers
: :
D4 D3
Use
1= 0
2= 1
a
1clerk switch (clerk push switch)/
2Clerk secret number key *
:
(a+b)
D2
1= 0
2= 2
Initialization pattern:
1For scanning/2For check tracking
b
No = 0
Yes = 1
:
Use Euro only.
D1
* When you select this option “Use clerk secret code key”, and your register doesn’t have this key on the default keyboard,
be sure to allocate <CLERK-#> (clerk secret number key) just after the initialization.
(Do NOT turn to OFF before allocating this key.)
Note:
Please check the receipt after initialization operation (machine initialization, flag clear operation and init2) that the machine
number is printed properly.
If error codes are printed on it, check the hardware and retry the operation.
P01 03-04-2004 11:58
C01 MC#01 000001
— Mode symbol/date/time
— Clerk descriptor/Mc-No./consecutive No.
INIT
— INIT symbol
— Copyright
(C) 2005 by CASIO
COMPUTER CO.,LTD.
All rights reserved.
TE-2200/2400 STD
— Model name
VER. :nnnn
LABEL :nnnnnn
— ROM version
— ROM label
VER. :nnnn
LABEL :nnnnnn
— ROM version
— ROM label
INIT. :nnnnnnnnnnnnnn
0002-98
— Initialization code
2000
— I/O parameter table record No./error code
:
18
Flag clear operation
1. Plug the power cord into an AC outlet.
JOURNAL
FEED
2. Hold down <RECEIPT FEED>.
REG2 X1
REG1
OFF
RF
Z1
X2/Z2
3. Turn the mode switch to PGM position.
4. Release <RECEIPT FEED>.
I
PGM
You should see “FFFFFFFFFF” on the display.
If 10 Fs are not shown or another character are shown,
immediately set the mode switch to OFF and restart from
RECEIPT
FEED
JOURNAL
FEED
the beginning of this procedure.
5. Press <SUBTOTAL> to complete.
After completion of flag clear, receipt is issued.
Note: After flag clear, clerk 1 is assigned automatically. So do not program clerk 1 as not assignable or
not operable in PGM mode.
Init 2 operation
1. Plug the power cord into an AC outlet.
JOURNAL
FEED
2. Hold down <RECEIPT FEED>.
REG2 X1
REG1
OFF
RF
Z1
X2/Z2
3. Turn the mode switch to PGM position.
4. Release <RECEIPT FEED>.
PGM
You should see “FFFFFFFFFF” on the display.
If 10 Fs are not shown or another character are shown,
immediately set the mode switch to OFF and restart from
RECEIPT
FEED
JOURNAL
FEED
the beginning of this procedure.
5. Enter “8888888888” and press <CHECK TEND> to complete.
After completion, receipt is issued.
TE-2200/2400 Dealer's Manual
19
Initialization
Entering diag mode
1. Plug the power cord into an AC outlet.
RECEIPT
FEED
2. Hold down <JOURNAL FEED>.
REG2 X1
REG1
OFF
RF
Z1
X2/Z2
3. Turn the mode switch to PGM position.
4. Release <JOURNAL FEED>.
PGM
5. Enter “99990000” and press <SUBTOTAL> to enter the diagnosis.
RECEIPT
FEED
JOURNAL
FEED
Password
During initialize operation, you can program the password for PGM 3 ~ 7. If it is set, every time you enter PGM 3 ~ 7
mode, you must input this password by the following procedure.
1. Press <#-1> (normally <CASH/AMT TEND>).
2. Enter password.
3. Press <#-2> (normally <SUBTOTAL>).
Otherwise, you can do nothing in the PGM 3 ~ 7 mode.
20
Programming (General explanation)
Program sub mode (P1 thru P7 mode)
Program mode contains seven sub modes listed below. When you change the mode switch to PGM mode, the register is
always in the PGM 1 mode. In case of using other mode, enter the sub mode number (2 ~ 7) and press <SUBTOTAL>.
• PGM1: unit price, rate, date, time, scanning PLU unit price maintenance
• PGM2: descriptor, name, message
• PGM3: machine feature (general function, clerk, etc.), key feature (department, transaction), scanning PLU maintenance
• PGM4: key allocation
• PGM5: file allocation
• PGM6: program reading
• PGM7: auto-program, system utility
Entering the program sub mode
Procedure (for PGM 1, 2 mode)
P
661s
6
6
a
a
: : : :
password (4-digit)
6
6
s
s
6
6
PGM
Mode switch
PGM1
PGM2
6
2s
: : : :
password (4-digit)
1. Enter password for PGM 1, 2 mode. If the register has no password for the PGM1 and 2 mode, you need not to enter it.
2. Press <SUBTOTAL>. An error occurs if you try to enter the PGM1 or 2 mode without inputting a password (when one is
programmed), or if the password you input does not match the one programmed for the register.
To avoid repetition, the above operation is abbreviated to the following for all of the other procedure in this manual.
This password is defined by the address code 02 of the general function program.
Procedure (for PGM 3 ~ 7 mode)
6
3
7s
6
a
: : : :
6
s
6
PGM 3 ~ 7
PGM
Mode switch
password (4-digit)
1. Enter password for PGM 3 ~ 7 mode. If the register has no password for the PGM 3 ~ 7 mode, you need not to enter it.
2. Press <SUBTOTAL>. An error occurs if you try to enter the PGM 3 ~ 7 mode without inputting a password (when one is
programmed), or if the password you input does not match the one programmed for the register.
To avoid repetition, the above operation is abbreviated to the following for all of the other procedure in this manual.
This password is defined during initialization operation.
TE-2200/2400 Dealer's Manual
21
Programming (General explanation)
22
File allocation (Program 5)
File allocation program
Programming procedure
6 5s 6 : : : s 6 : : a 6 s
PGM
Mode switch
File record number (see next pages.)
File number (see next pages.)
File attribution code (see below.)
Consolidation file
Daily sales Periodic 1
File attribu-
tion code
daily sales
Periodic 1 Periodic 2
Periodic 2
0
1
2
3
4
5
✔
✔
✔
✔
✔
✔
P
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
TE-2200/2400 Dealer's Manual
23
File allocation programming (P5)
File number list
File
No.
Record
Max No.
Attribu- Allocat- Default
File description
Description
length of records
tion
able
Rec. No.
System files
088
089
091
093
094
095
096
097
098
099
Auto-program work
6
6
1
1
Work
Work
No
No
1
1
Consecutive number work
Terminal connection table
Printer connection table
Start date
12
5
1
Program
Program
Buffer
Yes
Yes
No
32
3
7
4
1
1
Initialize code
7
1
Program
Program
Program
Program
Buffer
No
1
AT command
62
8
2
Yes
Yes
No
2
Online password
I/O parameter table
System error log
1
1
4
2
4
11
99
Yes
99
Function and total files
001
---
---
---
---
---
002
---
---
---
---
---
004
---
---
---
---
---
005
---
---
---
---
---
006
---
---
---
---
---
009
---
---
---
---
---
Fixed totalizer
22
10
10
10
10
10
35
10
10
10
10
10
73
30
30
30
30
30
59
25
25
25
25
25
22
10
10
10
10
10
24
20
20
20
20
20
99
99
Pgm/Sale
Sales
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
99
99
0
(periodic total 1)
(periodic total 2)
99
Sales
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Transaction key
99
Sales
0
99
Sales
0
99
Sales
0
999
999
999
999
999
999
*A
*A
*A
*A
*A
*A
99
Pgm/Sale
Sales
30
30
0
(periodic total 1)
(periodic total 2)
Sales
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
PLU
Sales
0
Sales
0
Sales
0
Pgm/Sale
Sales
216
0
(periodic total 1)
(periodic total 2)
Sales
0
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Department
Sales
0
Sales
0
Sales
0
Pgm/Sale
Sales
30
30
0
(periodic total 1)
99
(periodic total 2)
99
Sales
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Group
99
Sales
0
99
Sales
0
99
Sales
0
99
Pgm/Sale
Sales
10
0
(periodic total 1)
99
(periodic total 2)
99
Sales
0
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Hourly sales
99
Sales
0
99
Sales
0
99
Sales
0
99
Pgm/Sale
Sales
24
0
(periodic total 1)
99
(periodic total 2)
99
Sales
0
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
99
Sales
0
99
Sales
0
99
Sales
0
*A: Depend on the model
24
File
No.
Record
Max No.
Attribu- Allocat- Default
File description
Description
length of records
tion
able
Rec. No.
010
---
Monthly sales
20
20
20
20
20
20
28
10
10
10
10
10
20
8
31
31
31
31
31
31
99
99
99
99
99
99
3
Pgm/Sale
Sales
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
31
0
0
0
0
0
0
0
0
0
0
0
3
3
(periodic total 1)
---
(periodic total 2)
Sales
---
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Table analysis
Sales
---
Sales
---
Sales
018
---
Pgm/Sale
Sales
(periodic total 1)
---
(periodic total 2)
Sales
---
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Grand total
Sales
---
Sales
---
Sales
020
---
Pgm/Sale
Sales
(daily consolidation)
3
Check files
P
015
056
060
Check index
255
100
100
200
1500
9999
Buffer
Buffer
Buffer
Yes
Yes
Yes
(60)*B
(80)*B
(900)*B
Separate check buffer
Check detail
Clerk files
007
030
011
---
Clerk
38
9
99
Program
Program
Sales
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
15
10
150
150
0
Clerk detail link
200
Clerk detail
10
10
10
10
10
10
99 × 99
99 × 99
99 × 99
99 × 99
99 × 99
99 × 99
(periodic total 1)
Sales
---
(periodic total 2)
Sales
---
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Sales
0
---
Sales
0
---
Sales
0
Time and attendance files
019
061
Time and attendance
Employee
16
17
999
99
Sales
Yes
Yes
0
Program
10
Scanning PLU files
016
040
051
---
Scanning PLU
58
8
*A
100
Pgm/Sale
Program
Pgm/Sale
Sales
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(<-)*C
Non PLU table
(10)*C
Mix & match table
(periodic total 1)
30
10
10
10
10
10
42
42
2
99
0
99
0
---
(periodic total 2)
99
Sales
0
---
(daily consolidation)
(periodic 1 consolidation)
(periodic 2 consolidation)
Batch maintenance PLU
Direct maintenance PLU
Scanning PLU index
One touch NLU table
99
Sales
0
0
---
99
Sales
---
99
Sales
0
070
071
076
077
1000
1000
S-PLU + 2
999
Program
Program
Buffer
(100)*C
(50)*C
Automatic (5002)*C
7
Program
Yes
Yes
(10)*C
0
Arrangement file
038
Arrangement table
11
9999
Program
*A: Depend on the model.
*B: Allocate if you select “check tracking pattern” initialization, (refer to page 24 of this manual).
*C: Allocate if you select “scanning pattern” initialization, (refer to page 24 of this manual).
TE-2200/2400 Dealer's Manual
25
File allocation programming (P5)
File
No.
Record
Max No.
Attribu- Allocat- Default
File description
Description
length of records
tion
able
Rec. No.
Program / message / buffer files
022
023
024
025
028
029
032
033
034
036
039
041
046
047
049
062
065
067
068
073
074
078
079
080
081
082
083
085
086
General control
5
16
12
74
60
24
24
40
40
100
40
3
37
42
Program
Program
Program
Program
Program
Program
Program
Program
Program
Buffer
No
No
37
Special character
Report header
42
25
No
26
Tax table
10
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
4
Set menu table
999
10
(10)*B
Batch X/Z
4
4
Receipt message
42
Check endorse message
Slip/external printer message
Registration buffer
Character recall
4
0
42
0
1200
999
9
80
10
0
Program
Program
Program
Program
Buffer
Check print
Character key table
Graphic logo
6
*E
168
600
99
*E
168
0
48
50
22
12
48
48
4
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Print buffer (for external printer)
Scheduler
Program
Program
Program
Program
Program
Program
Program
Program
Program
Program
Program
Program
Program
Buffer
0
Order character
99
0
Graphic logo (for external printer)
Watermark print
168
168
999
*F
0
0
Bottle link table
0
Key table
24
16
24
16
16
16
16
24
40
150
0
Miscellaneous message
Printing guidance message
Error message
52
*D
*D
*D
*D
*D
*D
*D
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
68
0
191
11
0
Registration guidance message
X/Z guidance message
Program guidance message
Help message
0
38
0
92
0
199
500
0
Slip print buffer
0
*A: Depend on the model.
*B: Allocate if you select “check tracking pattern” initialization, (refer to page 24 of this manual).
*C: Allocate if you select “scanning pattern” initialization, (refer to page 24 of this manual).
*D: Allocate these files if you want to change the default message.
*E: 67 for TE-2200, 77 for TE-2400Eu, 70 for TE-2400US.
*F: 84 for TE-2200, 112 for TE-2400.
26
Issuing program reading report of program 5 mode
Issuing procedure
6 5s 6 s
PGM
Mode switch
Report sample
— Program read symbol
P05....................
— File name
FILE0001
— Sales file record length/No. of records of daily sales/periodic sales 1/periodic sales 2
— Consolidation file record length/No. of records of daily sales/periodic sales 1/periodic sales 2
22bytes 99 99 99
10bytes 99 99 99
FILE0002
— Hyphen means no record.
— Remaining RAM capacity
20,234
35bytes 100 -- --
10bytes 100 -- --
P
RAM
TE-2200/2400 Dealer's Manual
27
File allocation programming (P5)
28
Key allocation (Program 4)
Key allocation program
Programming procedure
By pressing the appropriate key
See Menu sheet No. section
6 4s6 :000s6
PGM
Mode switch
Menu sheet number
This step can be
skipped for
transaction key.
to other key
Set the same function
~
6 : : 6 : : : 6
6 s
#-nn
Appropriate key
(white key on the next page)
• Function code
P
• Record No. (department/transaction)
• Random code or record No. (flat-PLU)
By entering physical key code
See Menu sheet No. section
6 4s 6 : 6 : : :s 6
PGM
Mode switch
Physical key code
(see the next page.)
Menu sheet number
This step can be
skipped for
transaction key.
to other key
6 :~ : 6 : : : 6 a 6 s
• Function code
• Record No. (department/transaction)
• Random code or record No. (flat-PLU)
Menu sheet number
Description
(for transaction key)
Description
(for Dept/flat-PLU)
Menu sheet
number
0 or skip entering Set a function to the 1st ~ 6th menu sheets. Set a function to the programmed menu sheet.
1
2
3
4
5
6
Set a function to the 1st menu sheet.
Set a function to the 2nd menu sheet.
Set a function to the 3rd menu sheet.
Set a function to the 4th menu sheet.
Set a function to the 5th menu sheet.
Set a function to the 6th menu sheet.
Set a function to the 1st menu sheet.
Set a function to the 2nd menu sheet.
Set a function to the 3rd menu sheet.
Set a function to the 4th menu sheet.
Set a function to the 5th menu sheet.
Set a function to the 6th menu sheet.
TE-2200/2400 Dealer's Manual
29
Key allocation programming (P4)
Configuration of the physical key layout
TE-2200
RECEIPT
FEED
JOURNAL
FEED
071
070
069
068
067
066
C
065
7
064
063
8
062
061
9
060
059
058
057
056
055
054
053
052
051
050
049
048
047
046
045
044
043
042
041
040
039
038
037
036
035
034
033
032
031
030
029
028
027
026
025
024
023
022
014
020
019
018
017
015
016
021
013
081
080
079
078
077
076
075
074
073
072
4
5
6
1
2
3
0
011
012
TE-2400 for Eu
RECEIPT JOURNAL
038
037
036
035
034
033
032
045
044
043
042
041
040
039
052
051
050
049
048
047
046
059
066
065
064
063
062
061
060
073
080
079
078
077
076
075
074
087
094
093
092
091
090
089
088
101
108
107
106
105
104
103
102
031
029
028
027
026
025
024
FEED
FEED
058
057
056
055
054
053
072
071
070
069
068
067
086
085
084
083
082
081
100
099
098
097
096
095
030
023
019
022
021
020
014
018
017
015
016
C
7
4
1
0
8
5
9
6
2
3
011
012
013
TE-2400 for US
RECEIPT JOURNAL
045
044
043
042
041
040
039
052
051
050
049
048
047
046
059
058
057
056
055
054
053
066
065
064
063
062
061
060
073
072
071
070
069
068
067
080
079
078
077
076
075
074
087
086
085
084
083
082
081
094
093
092
091
090
089
088
101
100
099
098
097
096
095
108
107
106
105
104
103
102
038
037
036
035
027
033
032
031
030
029
028
027
026
025
024
FEED
FEED
023
019
022
021
020
014
018
017
015
016
C
7
4
1
0
8
5
9
6
2
3
011
012
013
The shadowed key cannot be programmed with any other functions.
<00>, <000>, and <.> functions are only allocated to <#011> or <#012> keys.
30
Function code list
Function
Add check
Arrangement
Birth date
Bill copy
Bottle return
Cancel
Code
094 ADD CHK
044 ARG
Initial character
Function
Normal receipt
OBR
Old check
One touch NLU
Open
Code
016 NRMRCT
103 OBR
092 OLD CHK
138 NLU
067 OPEN
068 OPEN2
117 OPEN CHK
073 OPE X/Z
021 PD
022 P.UP
029 +
048 PLU#
026 PB
079 PBST
030 %+
049 PRC
104 PRC CHG
008 PRCINQ
069 PRICE SHIFT
083 QT
031 TAX
131 RECALL
038 RCT
076 RCT ON/OFF
020 RC
060 RED
Initial character
047 BILL
053 BR
236 CANCEL
001 CASH
002 CHARGE
039 CK.E
012 CHKP
003 CHECK
072 CLK#
Open2
Cash amount tendered
Charge
Open check
Operator read/reset
Paid out
Pick up
Plus
Check endorsement
Check print
Check tender
Clerk number
Clock-in/out
Coupon
Coupon 2
Credit
Cube
Currency exchange
Customer number
Date/Time
Decimal point
Declaration
Department
Deposit
Discount
Eat-in
EBT tender
Enter
Error correct
Flat PLU *
Food stamp status shift
Food stamp subtotal
Food stamp tender
Help
Ketten Bon
Loan
Lock out unused key
Manual tax
Media change
Menu shift
Merchandise subtotal
Minus
PLU
108 CLOCK-IN/OUT Previous balance
023 COUPON
036 CPN2
004 CREDIT
090 XXX
045 CE
043 CT
101 DATE/TIME
098 .
061 DECLA
nn051 DEPTnn
025 DEPOSIT
028 %–
128 EAT-IN
007 EBTTD
105 ENT
Previous balance subtotal
Premium
Price
Price change
Price inquiry
Price shift
Quantity/for
Rate tax
Recall
Receipt
Receipt on/off
Received on account
Red price
Refund
Review
Separate check
Slip back feed/release
Slip feed/release
Slip print
Square
Stock inquiry
Store
Subtotal
Table number
Takeout
Tax exempt
Tax status shift
Taxable amount subtotal
Text print
P
033 RF
071 REVIEW
095 SEP CHK
054 SB/R
056 SF/R
055 SLIP
084 XX
009 STKINQ
130 STORE
075 SUBTOTAL
058 TBL#
129 TAKE-OUT
062 EXEMPT
057 T/S
034 CORR
nnnn063 PLUnnnn
059 F/S
081 FSST
005 FSTD
141 HELP
113 X/KETTEN
019 LOAN
000
032 TAX
118 MEDIA CHG
064 MENU
080 MDST
027 -
077 TAST
011 PRT
Multiplication/Date/Time
Multiplication
New balance
New check
New/old check
No sale
082 X
100 X
006 NB
091 NEW CHK
093 NEW/OLD
042 NS
Text recall
Three zero
Tip
Tray total
Two zero
010 CHAR
097 000
015 TIP
074 TRAY TL
096 00
037 VLD
Validation
VAT
Non-add
040 #
046 VAT
Non-add/No sale
041 #/NS
Void
035 VOID
* These functions cannot be allocated on TE-2200.
TE-2200/2400 Dealer's Manual
31
Key allocation programming (P4)
Issuing program reading report of program 4 mode
Issuing procedure
64s 6 s
PGM
Mode switch
Report sample
—
Program read symbol
P04....................
1-----------------------
—
—
Function character/rec-#/file-#
Hard key code/function code
00
0015-02
011-096
0009-02
012-098
0004-02
013-001
.
CASH
32
Key function/machine feature (Program 3)
General control program
Programming procedure
6 3s6 : : 22s6 : : ~ :: a 6 s
PGM
Mode switch
Program data
Address code
(2 digits)
(Max. 10 digits)
Program data (by address code)
Address code 01 (date order/password)
Description
Choice
Program code
Initial value
Date order
Significant
number (0 ~ 3)
:
Dependent upon
initialization code
Year/Month/Day = 0, 1
Day/Month/Year = 2, Month/Day/Year = 3
D10
Dependent upon
initialization code
Monetary mode
0 = 0, ~0 = 1, ~00 = 2, ~000 = 3
Significant
number (0 ~ 3)
:
D9
: : : : ; ; ; ;
Password in Manager mode
Password in X2/Z2 mode
D8 D7 D6 D5
D8 D7 D6 D5
P
: : : : ; ; ; ;
D4 D3 D2 D1
D4 D3 D2 D1
Address code 02 (password)
Description
Choice
Program code
Initial value
Significant
numbers
: : : : ; ; ; ;
Password in PGM1/PGM2 mode
D10 D9 D8 D7
D10 D9 D8 D7
; ;
; ;
Always “00”
D6 D5
D6 D5
; ; ; ; ; ; ; ;
Always “0000”
D4 D3 D2 D1
D4 D3 D2 D1
Address code 03 (consecutive number)
Description
Choice
Program code
Initial value
Yes = 1
No = 0
:
;
Reset consecutive number after daily fixed total reset report is issued.
D8
D8
;
;
Always “0”
D7
D7
Consecutive number set value.
It starts “set value + 1.”
:::::: ;;;;;;
D6 D5 D4 D3 D2 D1 D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
33
Key function/machine feature (P3)
Address code 04 (tax system, rounding, etc.)
Description
Choice
Program code
Initial value
Apply rounding for registration.
No rounding = 0, IF1 = 1, IF2 = 2, Danish = 3, Norwegian = 4,
Singaporean = 5, Finnish = 6, Australian = 7, South Africa = 8
:
;
Significant
number (0 ~ 8)
D10
D10
; or A
(EX-U.S.) (U.S.)
D9
Tax system
Significant
number (0 ~ 3)
:
Single tax system (1 ~ 10) = 0, U.S. tax system = 1
Canadian tax system = 2, Singaporean tax system = 3
D9
Receipt issuance:
Controlled by receipt on/off switch/key = 0
Always on (issue) = 1, Always off (not issue) = 2
Significant
number (0 ~ 2)
:
;
D8
D8
Yes = 0
No = 2
Allow amount tender in RF/REG– mode operation.
a
;
:
(a+b)
D7
(a+b)
D7
Cash drawer opening:
1Immediately when the transaction is finalized.
2After validation compulsory is released.
1= 0
2= 4
b
Significant
number (0 ~ 2)
Food stamp system (in case of D9 = 1)
Payable = 0, Illinois rule = 1, New Jersey rule = 2
;
:
D6
Significant
number (0 ~ 9)
D6
Tax exempt quantity of donuts tax. (in case of D9 = 2)
0 ~ 9 (“0” means “No donuts tax”.)
Round off = 0
Cut off = 1
Rounding of results produced by departments, PLUs and scanning PLUs
programmed with package prices and package quantities
:
;
Round up = 2
D5
D5
Maximum value
(0 ~ 9)
High amount limit specification for cash in drawer amount.
(Sentinel function)
: :
; ;
D4 D3
D4 D3
Number of zeros
(0 ~ 9)
; ;
; ;
Always “00”
D2 D1
D2 D1
Rounding
Australian rounding
IF 1 rounding
Last 1 digit of subtotal
Result
Last 1 digit of
Result
subtotal/cash change
0 ~ 2
3 ~ 7
8 ~ 9
0
5
0 ~ 2
3 ~ 7
8 ~ 9
0
5
10
10
IF 2 rounding
Norwegian rounding
Last 1 digit of subtotal
Result
Last 1 digit of
subtotal
0 ~ 4
5 ~ 9
0
Result
10
00 ~ 24
25 ~ 74
75 ~ 99
0
Singaporean rounding
50
Last 1 digit of
item, %+, %- registration
100
Result
Finnish rounding
0 ~ 2
3 ~ 7
8 ~ 9
0
5
Last 1 digit of
subtotal/cash change
Result
10
0 ~ 2
3 ~ 7
8 ~ 9
0
5
Danish rounding
Last 1 digit of
subtotal/change
10
Result
South Africa rounding
00 ~ 12
13 ~ 37
38 ~ 62
63 ~ 87
88 ~ 99
00
25
Last 1 digit of subtotal
Result
0 ~ 4
5 ~ 9
0
5
50
75
100
34
Address code 05 (print control for receipt)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
a
b
c
a
b
a
b
Print total line during finalization.
1= 0
2= 2
;
:
Time system:
124 hour system, 212 hour system
(a+b+c)
D10
(a+b+c)
D10
No = 0
Yes = 4
Feed one line after issuing receipt.
Print consecutive number by double sized letter (up to 3 digits).
Buffered receipt print *1
No = 0
Yes = 1
;
:
(a+b)
D9
(a+b)
D9
No = 0
Yes = 2
No = 0
Yes = 1
Skip item lines on journal. (journal skip)
Breakdown set menu printing on receipt, post receipt, guest receipt.
Always “000”
;
:
(a+b)
D8
(a+b)
D8
No = 0
Yes = 4
;;;
; ; ;
D7 D6 D6
D7 D6 D5
No = 0
Yes = 1
Print number of item sold.
a
S or ;
:
(EX-U.S.) (U.S.)
(a+b)
D4
(a+b)
D4
Yes = 0
No = 2
Print tax symbols.
b
Yes = 0
No = 1
:
;
Ignore receipt/journal paper end (not effective for external printer).
Print multiplication or item consolidation in one line.
Print C operation.
P
D3
D3
Yes = 0
No = 4
:
;
D2
D2
No = 0
Yes = 1
a
b
c
:
;
Yes = 0
No = 2
Print number of customers on header.
Print PLU number on receipt.
(a+b+c)
D1
(a+b+c)
D1
No = 0
Yes = 4
*1: Select “Yes” if you want to print receipts with watermarks.
TE-2200/2400 Dealer's Manual
35
Key function/machine feature (P3)
Address code 06 (calculation & operation control)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
Follow the taxable status and commission status of previous item when +/-
operation is performed.
a
b
c
a
b
c
a
b
a
b
a
b
c
a
b
c
a
b
c
a
b
c
a
b
a
b
;
:
No = 0
Yes = 2
Force to register rate tax before finalization.
(a+b+c)
D10
(a+b+c)
D10
No = 0
Yes = 4
Force a money declaration by b, n, N before read/reset operation.
Force to press s before finalization
No = 0
Yes = 1
:
;
Yes = 0
No = 2
Allow credit balance while finalization.
(a+b+c)
D9
(a+b+c)
D9
Yes = 0
No = 4
Allow multiple refund/register minus operation.
Affect the result of +/-, %+/%-, mix & match to the item. (Net totalling)
Include add-on/add-in tax in net total
No = 0
Yes = 1
:
;
(a+b)
D8
(a+b)
D8
Yes = 0
No = 2
Yes = 0
No = 2
Include commission in net total.
:
;
Treatment of department key numeric inputs:
1Treat as amount override
2Treat as quantity extensions
1= 0
2= 4
(a+b)
D7
(a+b)
D7
No = 0
Yes = 1
Clear the key buffer when a receipt is issued. (REG1/2 only)
Sounds key catch tone.
:
;
Yes = 0
No = 2
(a+b+c)
D6
(a+b+c)
D6
No = 0
Yes = 4
Allow to issue post receipt, even if the original one is issued.
No = 0
Yes = 1
Allow program 1 programming in the manager control mode
(X1 mode).
;
:
No = 0
Yes = 2
Display “seconds” during time display.
(a+b+c)
D5
(a+b+c)
D5
No = 0
Yes = 4
Connect slit drawer.
RF = 0
REG– = 1
RF mode status
:
;
No = 0
Yes = 2
Prohibit registration when the stock quantity becomes negative.
Alert when the stock quantity becomes under minimum stock quantity.
Affect to stock quantity even if the refund operation.
(a+b+c)
D4
(a+b+c)
D4
No = 0
Yes = 4
No = 0
Yes = 1
Treatment of flat-PLU/One touch NLU key numeric inputs:
1Treat as amount override (effective for flat-PLU only)
2Treat as quantity extensions
1= 0
2= 2
:
;
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
Allow one registration of +/-, %+/%- per one transaction.
No = 0
Yes = 1
Rounding on the least significant digit of %+/%- registration:
0 ~ 2 → 0, 3 ~ 7 → 5, 8 ~ 9 → 10
:
;
Yes = 0
No = 2
(a+b)
D2
(a+b)
D2
Display separator.
Yes = 0
No = 2
Allow numeric entry while compulsory drawer opening.
PLU numbering: 1By memory No. (sequential), 2By random code
;
:
1= 0
2= 4
(a+b)
D1
(a+b)
D1
36
Address code 07 (menu & price shift)
Description
Choice
Program code
Initial value
Maintenance of last menu shift:
1Do not maintain
1= 0
2= 1
3= 2
:
;
2Until next menu shift specification
3Within this transaction
D8
D8
Maintenance of last price shift:
1Do not maintain
2Until next price shift specification
3Within this transaction
1= 0
2= 1
3= 2
:
;
D7
D7
;
;
Always “0”
D6
D6
Significant
:
;
Sheet number of the parent menu sheet
Summed up menu sheet 1 to parent menu sheet.
Summed up menu sheet 2 to parent menu sheet.
Summed up menu sheet 3 to parent menu sheet.
Summed up menu sheet 4 to parent menu sheet.
Summed up menu sheet 5 to parent menu sheet.
Summed up menu sheet 6 to parent menu sheet.
Always “0”
number (1 ~ 6)
D5
D5
No = 0
Yes = 1
a
b
c
a
b
c
No = 0
Yes = 2
:
;
(a+b+c)
D4
(a+b+c)
D4
No = 0
Yes = 4
No = 0
Yes = 1
No = 0
Yes = 2
:
;
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
P
;
;
D2
D2
Yes = 0
No = 1
:
;
Reset child menu sheets with parent menu sheet together.
This program is not effective for TE-2200.
D1
D1
TE-2200/2400 Dealer's Manual
37
Key function/machine feature (P3)
Address code 08 (print control for fixed total report)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
a
b
c
a
Print gross sales total on fixed total report (GROSS)
;
Yes = 0
No = 2
:
Print net sales total on fixed total report (NET)
(a+b+c)
D10
(a+b+c)
D10
Yes = 0
No = 4
Print cash in drawer total on fixed total report (CAID)
Yes = 0
No = 1
Print difference between money declaration and cash in drawer total on fixed
total report (CATL, CA+, CA-) (Skip these lines, if “CAID” is set to skip.)
G
:
Yes = 0
No = 2
Print charge in drawer total on fixed total report (CHID)
b
(a+b+c)
D9
(a+b+c)
D9
Print difference between money declaration and charge in drawer total on
fixed total report (CHTL, CH+, CH-) (Skip these lines, if “CHID” is set to
skip.)
Yes = 0
No = 4
c
a
b
c
Yes = 0
No = 1
Print check in drawer total on fixed total report (CKID)
Print difference between money declaration and check in drawer total on
fixed total report (CKTL, CK+, CK-) (Skip these lines, if “CKID” is set to
skip.)
Yes = 0
No = 2
S
:
(a+b+c)
D8
(a+b+c)
D8
Yes = 0
No = 4
Print credit in drawer total on fixed total report (CRID(1)~ (4))
Print difference between money declaration and credit in drawer total on
fixed total report (CRTL, CR+, CR-) (Skip these lines, if “CRID” is set to
skip.)
Yes = 0
No = 1
a
b
c
a
b
c
a
b
a
b
c
a
b
c
J
:
Yes = 0
No = 2
Print food stamp in drawer total on fixed total report (FSID)
Print food stamp cash change total on fixed total report (FSCACG)
Print EBT in drawer total on fixed total report (EBTTL)
Print EBT cash change total on fixed total report (EBTCACG)
Print RF mode total on fixed total report (RF)
(a+b+c)
D7
(a+b+c)
D7
Yes = 0
No = 4
Yes = 0
No = 1
Yes = 0
No = 2
D
:
(a+b+c)
D6
(a+b+c)
D6
Yes = 0
No = 4
Yes = 0
No = 1
Print the net number of customers on fixed total report (CUST)
Print the average sales per customer on fixed total report (AVER)
Print check cashing handling fee total on fixed total report (FEE)
Print temporary finalize service charge total on fixed total report (+)
Not used
S
:
(a+b)
D5
(a+b)
D5
Yes = 0
No = 2
Yes = 0
No = 1
Yes = 0
No = 2
J
:
(a+b+c)
D4
(a+b+c)
D4
(Always “4”)
Yes = 0
No = 1
Print commission 1 total on fixed total report (C-1)
Print commission 2 total on fixed total report (C-2)
Yes = 0
No = 2
J
:
(a+b+c)
D3
(a+b+c)
D3
Print foreign currency cash in drawer and check in drawer totals on fixed
total report (CECA1~ 4, CECK1~ 4)
Yes = 0
No = 4
Print <MINUS>, <COUPON>, <%–> and mix & match operation net total
on fixed total report (DC)
Yes = 0
No = 1
a
J
:
Print <REFUND> and <VOID> operation net total on fixed total report
(REF)
Yes = 0
No = 2
b
(a+b+c)
D2
(a+b+c)
D2
Print total number of <CLEAR> operation net total on fixed total report
Yes = 0
No = 4
c
a
b
c
(CLEAR)
Yes = 0
No = 1
Print nontaxable totals on fixed total report (NON TAX)
Print rounding totals on fixed total report (ROUND)
Print cancellation total on fixed total report (CANCEL)
A (Australia)
:
Yes = 0
No = 2
or
(a+b+c)
D1
D (other area)
Yes = 0
No = 4
D1
38
Address code 09 (print control for fixed total report)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
Print taxable amount 1 total on fixed total report (TA1)
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
Yes = 0
No = 2
:
F
Print tax 1 total on fixed total report (TX1)
(a+b+c)
D10
(a+b+c)
D10
Yes = 0
No = 4
Print tax exempt 1 total on fixed total report (EX1)
Print taxable amount 2 total on fixed total report (TA2)
Print tax 2 total on fixed total report (TX2)
Yes = 0
No = 1
J (Australia)
or
Yes = 0
No = 2
:
(a+b+c)
D9
F (other area)
D9
Yes = 0
No = 4
Print tax exempt 2 total on fixed total report (EX2)
Print taxable amount 3 total on fixed total report (TA3)
Print tax 3 total on fixed total report (TX3)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D8
(a+b+c)
D8
Yes = 0
No = 4
Print tax exempt 3 total on fixed total report (EX3)
Print taxable amount 4 total on fixed total report (TA4)
Print tax 4 total on fixed total report (TX4)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D7
(a+b+c)
D7
Yes = 0
No = 4
Print tax exempt 4 total on fixed total report (EX4)
Print taxable amount 5 total on fixed total report (TA5)
Print tax 5 total on fixed total report (TX5)
Yes = 0
No = 1
P
Yes = 0
No = 2
:
J
(a+b+c)
D6
(a+b+c)
D6
Yes = 0
No = 4
Print tax exempt 5 total on fixed total report (EX5)
Print taxable amount 6 total on fixed total report (TA6)
Print tax 6 total on fixed total report (TX6)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D5
(a+b+c)
D5
Yes = 0
No = 4
Print tax exempt 6 total on fixed total report (EX6)
Print taxable amount 7 total on fixed total report (TA7)
Print tax 7 total on fixed total report (TX7)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D4
(a+b+c)
D4
Yes = 0
No = 4
Print tax exempt 7 total on fixed total report (EX7)
Print taxable amount 8 total on fixed total report (TA8)
Print tax 8 total on fixed total report (TX8)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D3
(a+b+c)
D3
Yes = 0
No = 4
Print tax exempt 8 total on fixed total report (EX8)
Print taxable amount 9 total on fixed total report (TA9)
Print tax 9 total on fixed total report (TX9)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D2
(a+b+c)
D2
Yes = 0
No = 4
Print tax exempt 9 total on fixed total report (EX9)
Print taxable amount 10 total on fixed total report (TA10)
Print tax 10 total on fixed total report (TX10)
Print tax exempt 10 total on fixed total report (EX10)
Yes = 0
No = 1
Yes = 0
No = 2
:
J
(a+b+c)
D1
(a+b+c)
D1
Yes = 0
No = 4
TE-2200/2400 Dealer's Manual
39
Key function/machine feature (P3)
Address code 10 (print control for taxable amount, till timer)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
a
b
c
a
b
c
a
b
c
Print taxable amount 1 on receipt/journal.
:
;
Yes = 0
No = 2
Print taxable amount 2 on receipt/journal.
Print taxable amount 3 on receipt/journal.
Print taxable amount 4 on receipt/journal.
Print taxable amount 5 on receipt/journal.
Print taxable amount 6 on receipt/journal.
Print taxable amount 7 on receipt/journal.
Print taxable amount 8 on receipt/journal.
Print taxable amount 9 on receipt/journal.
(a+b+c)
D10
(a+b+c)
D10
Yes = 0
No = 4
Yes = 0
No = 1
:
;
Yes = 0
No = 2
(a+b+c)
D9
(a+b+c)
D9
Yes = 0
No = 4
Yes = 0
No = 1
Yes = 0
No = 2
:
;
(a+b+c)
D8
(a+b+c)
D8
Yes = 0
No = 4
Yes = 0
No = 1
:
;
Print taxable amount 10 on receipt/journal.
Always “0”
D7
D7
;
;
D6
D6
1= 0
2= 1
Prohibit registrations,
1while all drawers are opened. 2while clerk’s own drawer is opened.
a
:
;
(a+b)
D5
(a+b)
D5
No = 0
Yes = 2
b
Ignore compulsory drawer sensor.
Till timer (00 ~ 59 minutes)
Significant
numbers
: :
; ;
D4 D3
D4 D3
Significant
numbers
: :
; ;
Till timer (00 ~ 59 seconds)
D2 D1
D2 D1
Address code 13 (online control)
Description
Choice
Program code
Initial value
Issue reset report at satellites during Z consolidation. *
(for in/online master/satellite)
No = 0
Yes = 2
a
:
;
(a+b)
D5
(a+b)
D5
Add daily total data to consolidation file when reset operation has been
performed. (for inline master/satellite)
Yes = 0
No = 4
b
No = 0
Yes = 1
:
;
Prohibit operation when data exists in the consolidation file.
D4
D4
; ; ;
; ; ;
Always “000”
D3 D2 D1
D3 D2 D1
* This option is effective, when consolidation is activated by job command.
40
Address code 14 (currency exchange control)
Description
Choice
Program code
Initial value
Significant
number (0 ~ 9)
;
:
Monetary mode of CECA1 and CECK1 in fixed total report:
D8
D8
1= 0
Decimal for CECA1 and CECK1 in fixed total report:
a
2= 1
;
1Period = 0, 2Comma = 1
:
(a+b)
D7
(a+b)
D7
1= 0
2= 4
Separator for CECA1 and CECK1 in fixed total report:
1Comma = 0, 2Period = 1
b
Significant
number (0 ~ 9)
;
:
Monetary mode of CECA2 and CECK2 in fixed total report:
D6
D6
1= 0
2= 1
Decimal for CECA2 and CECK2 in fixed total report:
1Period = 0, 2Comma = 1
a
;
:
(a+b)
D5
(a+b)
D5
1= 0
2= 4
Separator for CECA2 and CECK2 in fixed total report:
1Comma = 0, 2Period = 1
b
Significant
number (0 ~ 9)
;
:
Monetary mode of CECA3 and CECK3 in fixed total report:
D4
D4
1= 0
2= 1
Decimal for CECA3 and CECK3 in fixed total report:
1Period = 0, 2Comma = 1
a
;
:
(a+b)
D3
(a+b)
D3
1= 0
2= 4
Separator for CECA3 and CECK3 in fixed total report:
1Comma = 0, 2Period = 1
b
Significant
number (0 ~ 9)
;
:
Monetary mode of CECA4 and CECK4 in fixed total report:
D2
D2
1= 0
Decimal for CECA4 and CECK4 in fixed total report:
a
P
2= 1
1Period = 0, 2Comma = 1
;
:
(a+b)
D1
(a+b)
D1
1= 0
2= 4
Separator for CECA4 and CECK4 in fixed total report:
1Comma = 0, 2Period = 1
b
TE-2200/2400 Dealer's Manual
41
Key function/machine feature (P3)
Address code 15 (print control for reports)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
Zero skip department report.
Zero skip clerk report.
a
b
a
b
c
a
b
c
a
b
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
:
;
(a+b)
D10
(a+b)
D10
Yes = 0
No = 2
Yes = 0
No = 1
Zero skip transaction report.
Zero skip PLU report.
:
Yes = 0
No = 2
;
(a+b+c)
D9
(a+b+c)
D9
Yes = 0
No = 4
Zero skip hourly report.
Zero skip group report.
Yes = 0
No = 1
:
;
Yes = 0
No = 2
Zero skip monthly report.
Zero skip table analysis report.
(a+b+c)
D8
(a+b+c)
D8
Yes = 0
No = 4
Yes = 0
No = 2
Skip a not clocked out employee on the time & attendance report.
Zero skip mix & match report.
:
;
(a+b)
D7
(a+b)
D7
Yes = 0
No = 4
No = 0
Yes = 1
Prohibit issuing “OPEN CHECK Z” report.
:
;
No = 0
Yes = 2
Prohibit issuing “Daily Z” report, if opened check exists.
Skip the non-programmed record of scanning PLU saving data to CF card
Exclude the record No. field from scanning PLU saving data to CF card
Open cash drawer when the financial or fixed total report is issued.
Print PLU number on the PLU report.
(a+b)
D6
(a+b)
D6
Yes = 0
No = 4
Yes = 0
No = 1
Yes = 0
No = 2
:
;
(a+b)
D5
(a+b)
D5
No = 0
Yes = 4
No = 0
Yes = 1
Print sales ratio.
:
;
No = 0
Yes = 2
Issue double Z report.
(a+b+c)
D4
(a+b+c)
D4
No = 0
Yes = 4
Print the recalculate amount of taxable amount and tax amount of single tax.
Print average sales in the monthly report.
Yes = 0
No = 1
:
;
Contents of double Z report:
1: Fixed total report only, 2: Batch report *
* Fixed total should be included in this batch.
1= 0
2= 2
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
Reset actual stock quantity after PLU reset report issuance by batch X/Z.
Print reset counter.
Yes = 0
No = 1
:
;
No = 0
Yes = 2
Print item discount totalizer.
(a+b+c)
D2
(a+b+c)
D2
Print order of PLU report:
1Memory No. (sequential), 2= Random code
1= 0
2= 4
No = 0
Yes = 1
With character of X/Z data stored to CF card
With random code of X/Z data stored to CF card
With OBR code of X/Z data stored to CF card
:
;
No = 0
Yes = 2
(a+b+c)
D1
(a+b+c)
D1
No = 0
Yes = 4
42
Address code 16 (print control for grand total)
Description
Choice
Program code
Initial value
Contents of the periodic 1 total:
Significant
number (0 ~ 2)
• Normal registration only = 0
:
;
• Training registration only = 1
• Both normal registration and training registration = 2
D10
D10
Contents of the periodic 2 total:
Significant
number (0 ~ 2)
• Normal registration only = 0
:
;
• Training registration only = 1
• Both normal registration and training registration = 2
D9
D9
Yes = 0
No = 1
Journal printing of the periodic 1 report
a
:
;
(a+b)
D8
(a+b)
D8
Yes = 0
No = 2
Journal printing of the periodic 2 report
b
No = 0
Yes = 1
:
;
Print consecutive number range of the day on daily fixed total report.
Always “0000”
D7
D7
; ; ; ; ; ; ; ;
D6 D5 D4 D3
D6 D5 D4 D3
Yes = 0
No = 1
Print grand total 1 on periodic 1/periodic 2 reset report.
Print grand total 2 on periodic 1/periodic 2 reset report.
Print grand total 3 on periodic 1/periodic 2 reset report.
Print grand total 1 on daily sales reset report.
Print grand total 2 on daily sales reset report.
Print grand total 3 on daily sales reset report.
a
b
c
a
b
c
:
J
Yes = 0
No = 2
(a+b+c)
D2
(a+b+c)
D2
Yes = 0
No = 4
Yes = 0
No = 1
P
:
;
Yes = 0
No = 2
(a+b+c)
D1
(a+b+c)
D1
Yes = 0
No = 4
TE-2200/2400 Dealer's Manual
43
Key function/machine feature (P3)
Address code 17 (print control)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
Money declaration compulsory (cash) in REG/RF mode
a
b
c
:
;
No = 0
Yes = 2
Money declaration compulsory (charge) in REG/RF mode
Money declaration compulsory (check) in REG/RF mode
Money declaration compulsory (credit) in REG/RF mode
Always “0”
(a+b+c)
D10
(a+b+c)
D10
No = 0
Yes = 4
No = 0
Yes = 1
:
;
D9
D9
;
;
D8
D8
Commission:
1= 0
2= 1
a
1Taxable amount × commission rate
2(Taxable amount + VAT) × commission rate
:
;
(a+b)
D7
(a+b)
D7
Whenever pressing <PLUS>, <MINUS>, or <COUPON> the amount
registered is proportioned among all taxable amounts.
No = 0
Yes = 2
b
:
;
Rounding of commission:
Round off = 0, Cut off = 1, Round up = 2
Significant
number (0 ~ 2)
D6
D6
No = 0
Yes = 1
Append two zeros in unit price programming.
a
b
a
b
c
a
b
c
:
;
(a+b)
D5
(a+b)
D5
Print normal price and the difference between the normal price and the
reduced price on receipt.
No = 0
Yes = 2
Yes = 0
No = 1
Print date on receipt.
:
;
Yes = 0
No = 2
Print date on journal.
(a+b+c)
D4
(a+b+c)
D4
Yes = 0
No = 4
Print consecutive number on receipt/journal.
Print time on receipt.
Yes = 0
No = 1
:
;
Yes = 0
No = 2
Print time on journal.
(a+b+c)
D3
(a+b+c)
D3
Merge the same department/PLU/scanning PLU registration on buffered
receipt and post receipt. (Item consolidation)
No = 0
Yes = 4
; ;
; ;
Always “00”
D2 D1
D2 D1
44
Address code 18 (print control for guest receipt and slip)
Description
Choice
Program code
Initial value
Significant
numbers
: :
; ;
Maximum printing lines of slip (00 ~ 99)
D8 D7
D8 D7
Low = 0
High = 2
Slip printing speed:
a
“Maximum printing lines of slip” is necessary, if you select “High”.
:
;
(a+b)
D6
(a+b)
D6
No = 0
Yes = 4
b
Classify registered item by group on slip & guest receipt.
Always “0”
;
;
D5
D5
Yes = 0
No = 1
a
b
c
a
b
c
Print date on slip & guest receipt.
Print time on slip & guest receipt.
:
;
Yes = 0
No = 2
(a+b+c)
D4
(a+b+c)
D4
1= 0
2= 4
Print:
1Total only, 2Detail when D6 = 4 (item consolidated)
1= 0
2= 1
Slip print range:
1At the top of the transaction, 2This receipt
:
No = 0
Yes = 2
;
Enable slip auto line find.
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
Merge the same department/PLU/scanning PLU registration on slip & guest
receipt. (Item consolidation)
Significant
numbers
: :
; ;
Slip auto feed lines (00 ~ 99)
D2 D1
D2 D1
P
Address code 19 (order control)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
a
b
a
b
c
Print order with order character.
;
:
(a+b)
D9
(a+b)
D9
No = 0
Yes = 2
Print order with amount.
Yes = 0
No = 1
Alert when the order printer 1 goes down.
If “No”, backup processing is performed.)
;
:
Yes = 0
No = 2
Alert when the order printer 2 goes down.
(If “No”, backup processing is performed.)
(a+b+c)
D8
(a+b+c)
D8
No = 0
Yes = 4
Breakdown set menu printing on order.
No = 0
Yes = 1
Print double-height characters in UP-360/(internal R/J printer).
(not only for order, but also effective for receipt)
;
:
D7
D7
No = 0
Yes = 1
;
:
Show guidance for backup print of order. (when it is backed up from R/J)
D6
D6
;
;
Always “0”
D5
D5
No = 0
Yes = 2
a
b
a
b
Cut order.
;
:
(a+b)
D4
(a+b)
D4
No = 0
Yes = 4
Print dashed lines (hyphens).
Print orders even if training clerk is registered items.
No = 0
Yes = 2
;
:
(a+b)
D3
(a+b)
D3
No = 0
Yes = 4
Merge the same department/PLU/scanning PLU registration on order receipt.
(Item consolidation)
Significant
number
;
:
Number of feed lines before order printing (0 ~ 9)
Number of feed lines after order printing (0 ~ 9)
D2
D2
Significant
number
F
:
D1
D1
TE-2200/2400 Dealer's Manual
45
Key function/machine feature (P3)
Address code 21 (message control)
Description
Choice
Program code
Initial value
Print graphic type logo.
No = 0
Yes = 2
a
b
a
b
c
a
b
c
(If select “No”, character type logo is printed.)
:
;
(a+b)
D10
(a+b)
D10
No = 0
Yes = 4
Print watermark on receipt.
No = 0
Yes = 1
Print commercial message on slip/guest receipt.
Print bottom message on slip/guest receipt.
Print intermediate message on slip/guest receipt.
Print bill top message.
:
;
No = 0
Yes = 2
(a+b+c)
D9
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
Print bill copy message.
(a+b+c)
D8
(a+b+c)
D8
No = 0
Yes = 4
Print bill bottom message.
;
;
Always “0”
D7
D7
No = 0
Yes = 1
Print commercial message on receipts in REG/RF mode.
Print bottom message on receipts in REG/RF mode.
Print commercial message on journal in REG/RF mode.
Print bottom message on journal in REG/RF mode.
Print commercial message on receipts in X/Z mode.
Print bottom message on receipts in X/Z mode.
Print commercial message on journal in X/Z mode.
Print bottom message on journal in X/Z mode.
Print commercial message on receipt in PGM mode.
Print bottom message on receipt in PGM mode.
Print commercial message on journal in PGM mode.
Print bottom message on journal in PGM mode.
Print commercial message on FC or AUTO-PGM receipts.
Print bottom message on FC or AUTO-PGM receipts.
Print commercial message on FC or AUTO-PGM journal.
Print bottom message on FC or AUTO-PGM journal.
Print Australian GST MOF message.
a
b
c
a
b
c
a
b
c
a
b
c
a
b
c
a
b
:
;
No = 0
Yes = 2
(a+b+c)
D6
(a+b+c)
D6
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
(a+b+c)
D5
(a+b+c)
D5
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
(a+b+c)
D4
(a+b+c)
D4
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
(a+b+c)
D2
(a+b+c)
D2
No = 0
Yes = 4
No = 0
Yes = 1
:
;
(a+b)
D1
(a+b)
D1
No = 0
Yes = 4
46
Address code 25 (condiment etc.)
Description
Choice
Program code
Initial value
:
;
Yes = 0
No = 1
Enable to register a non-department link PLU.
D4
D4
Subtotal display:
1Both “rounded” and “not rounded” subtotal
2Only “not rounded” subtotal
A (Australia)
1= 1
2= 0
:
or
D3
; (other area)
(This option is effective for selecting Eu/Aus rounding specification only.)
D3
Previous item void:
1By using <VOID>; ordinary procedure
2By using <REVIEW>
:
1= 0
2= 1
A
D2
D2
No = 0
Yes = 1
Restrict (to 0 or 5) on the last one digit for amount tender.
Obey registration quantities of child PLU to its parent PLU.
a
b
c
F (Australia)
or
:
Yes = 0
No = 2
; (other area)
(a+b+c)
D1
D1
Restriction (to 0 or 5) on the last one digit for <CASH>, <RC>, <PD>,
money declaration amount (by <CASH> or <NON ADD>).
No = 0
Yes = 4
Address code 26 (check tracking)
Description
Choice
Program code
Initial value
Check tracking method:
1Check No., 2Table No.
1= 0
2= 1
a
:
;
P
(a+b)
D6
(a+b)
D6
Maximum digit of check number:
16-digit, 212-digit
(If you use “table analysis” or “table range”, select 1.)
1= 0
2= 4
b
Tax calculation by new balance
(Calculation result is not saved into totalizer.)
:
;
No = 0
Yes = 1
D5
D5
No = 0
Yes = 1
a
Enable to perform <NEW/OLD> during check tracking/clerk interrupt.
Print previous balance amount, when registration begins 0 with old check.
Always “000”
:
;
(a+b)
D4
(a+b)
D4
Yes = 0
No = 2
b
; ; ;
; ; ;
D3 D2 D1
D3 D2 D1
Address code 27 (clerk control)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
a
Enable clerk/cashier interrupt.
:
;
(a+b)
D10
(a+b)
D10
Print of clerk/cashier's name on receipt following sign back on at D10 = 1.
(enable clerk/cashier interrupt)
No = 0
Yes = 4
b
; ~ ;
; ~ ;
Always “0000000”
D9
~
D3
D9
~
D3
Significant
numbers
; ;
: :
Auto sign-off timer. (in second) (“00” means no auto sign-off.)
D2 D1
D2 D1
TE-2200/2400 Dealer's Manual
47
Key function/machine feature (P3)
Address code 28 (Euro)
Description
Choice
Program code
Initial value
Yes = 0
No = 1
;
:
Define Euro as the main currency.
Select rounding option:
D10
D10
Significant
number (0 ~ 2)
;
:
Round off = 0, Cut off = 1, Round up = 2
D9
D9
Significant
numbers
;;;;;;
D8 D7 D6 D5 D4 D3
::::::
D8 D7 D6 D5 D4 D3
Exchange rate (within 6-digits)
Decimal point position of exchange rate:
Integer only = 0
1st decimal place = 1, 2nd decimal place = 2, 3rd decimal place = 3,
4th decimal place = 4, 5th decimal place = 5, 6th decimal place = 6
Example: (D8 ~ D2)
Significant
number (0 ~ 6)
;
:
D2
D2
1 Euro = 1.977 DM; Set “0019773”
1 Euro = 1957.77319 Lit; Set “1957772”
;
;
Always “0”
D1
D1
Address code 29 (Euro)
Description
Choice
Program code
Initial value
Significant
number (0 ~ 3)
Monetary mode of sub currency:
0 = 0, ~0 = 1, ~00 = 2, ~000 = 3
:
S
D10
D10
Apply rounding for sub currency. *
No rounding = 0, IF1 = 1, IF2 = 2, Danish = 3, Norwegian = 4, Finnish = 6
Australia = 7, South Africa = 8
Significant
number (0 ~ 8)
:
;
D9
D9
Significant
number (0 ~ 2)
Cash drawer number of sub currency: 0 ~ 2
(“0” means main drawer.)
:
;
D8
D8
No = 0
Yes = 1
a
b
c
a
b
c
a
b
c
a
Print tendered amount in sub currency converted to main currency.
:
;
1= 0
2= 2
Selection of the currency of subtotal printout:
1Main currency only, 2Main and sub currency
(a+b+c)
D7
(a+b+c)
D7
No = 0
Yes = 4
Print total in sub currency by double sized letter.
1= 0
2= 1
Selection of the currency of change:
1Main currency, 2Sub currency
No = 0
Yes = 2
Print the cash in drawer of sub currency on fixed total reports.
(If the cash in drawer of main currency is skipped, this line is also skipped.)
:
;
(a+b+c)
D6
(a+b+c)
D6
1= 0
2= 4
Display symbol of sub currency:
1e(Euro), 2l(Local)
The currency to restrict (to 00, 25, 50, 75) on last two digits for amount
tendered: 1Main currency, 2Sub currency
(It is necessary to set this restriction to <CASH> key.)
1= 0
2= 1
No = 0
Yes = 2
:
;
Print rounding total of sub currency on fixed totalier report.
Last 1 digit for sub currency monetary amount entries to 0 or 5.
(a+b+c)
D5
(a+b+c)
D5
No = 0
Yes = 4
1= 0
2= 1
Selection of the change amount printout:
1Main and sub currency, 2Dependent upon D6 - a of this worksheet
:
;
Calculation method of change amount in sub currency:
1= 0
2= 2
1Convert the change amount in main currency into sub currency.
2Subtract the equivalent value of subtotal amount in sub currency from
the equivalent value of the tendered amount in sub currency.
(a+b)
D4
(a+b)
D4
b
; ; ;
; ; ;
Always “000”
D3 D2 D1
D3 D2 D1
* Refer to the Address code 04 programming.
48
Address code 30 (Internal thermal printer control)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
:
;
Journal compressed print (print by half height characters)
D4
D4
; ; ;
; ; ;
Always “000”
D3 D2 D1
D3 D2 D1
Address code 31 (scanning)
Description
Choice
Program code
Initial value
The oldest item is deleted if the scanning PLU file becomes full.
(If “No” is selected, alert only.)
:
;
Yes = 0
No = 1
D8
D8
No = 0
Yes = 1
a
b
a
b
c
Print consolidated scanning PLU reset report. (only for master) *
Print report before scanning PLU Z consolidation. *
Print scanning PLU code on receipt.
Print scanning PLU code on journal.
Print scanning PLU code on report.
:
;
(a+b)
D7
(a+b)
D7
No = 0
Yes = 4
No = 0
Yes = 1
:
H
No = 0
Yes = 2
(a+b+c)
D6
(a+b+c)
D6
No = 0
Yes = 4
P
; ;
; ;
Always “00”
D5 D4
D5 D4
Inactive days:
Significant
numbers
(000 ~ 999)
: : :
; ; ;
(If a scanning PLU did not move during these days period, this item will
be printed on the Inactive scanning PLU report.)
D3 D2 D1
D3 D2 D1
* These options are also effective, when consolidation is activated by job command.
Address code 32 (direct maintenance PLU)
Description
Choice
Program code
Initial value
Skip the unit price field programming of direct maintenance PLU file in
a
No = 0
Yes = 1
PGM 1 mode.
:
+
(a+b)
D9
(a+b)
D9
Skip the link field programming of direct maintenance PLU file in PGM 1
b
No = 0
Yes = 2
mode.
; ; ;
; ; ;
Always “000”
D8 D7 D6
D8 D7 D6
Skip the optimum stock field programming of direct maintenance PLU file
in PGM 3 mode.
No = 0
Yes = 4
:
;
D5
D5
Skip the unit price field programming of direct maintenance PLU file in
a
No = 0
Yes = 1
PGM 3 mode.
:
+
Skip the link field programming of direct maintenance PLU file in PGM 3
b
No = 0
Yes = 2
(a+b+c)
D4
(a+b+c)
D4
mode.
Skip the character field programming of direct maintenance PLU file in
c
No = 0
Yes = 4
PGM 3 mode.
Skip the status field programming of direct maintenance PLU file in PGM 3
a
No = 0
Yes = 1
mode.
:
+
Skip the bottle link field programming of direct maintenance PLU file in
b
No = 0
Yes = 2
(a+b+c)
D3
(a+b+c)
D3
PGM 3 mode.
Skip the mix & match field programming of direct maintenance PLU file in
c
No = 0
Yes = 4
PGM 3 mode.
; ;
; ;
Always “00”
D2 D1
D2 D1
TE-2200/2400 Dealer's Manual
49
Key function/machine feature (P3)
Address code 33 (batch PLU maintenance)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
Skip the record No. designation of batch maintenance PLU file.
a
b
a
b
c
a
b
c
:
;
(a+b)
D10
(a+b)
D10
No = 0
Yes = 4
Skip the optimum stock field programming of batch maintenance PLU file.
Skip the unit price field programming of batch maintenance PLU file.
Skip the link field programming of batch maintenance PLU file.
Skip the character field programming of batch maintenance PLU file.
Skip the status field programming of batch maintenance PLU file.
Skip the bottle link field programming of batch maintenance PLU file.
Skip the mix & match field programming of batch maintenance PLU file.
Always “000”
No = 0
Yes = 1
No = 0
Yes = 2
:
;
(a+b+c)
D9
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
;
No = 0
Yes = 2
(a+b+c)
D8
(a+b+c)
D8
No = 0
Yes = 4
; ; ;
; ; ;
D7 D6 D5
D7 D6 D5
; ;
; ;
Always “00”
D4 D3
D4 D3
; ;
; ;
Always “00”
D2 D1
D2 D1
Address code 34 (backlight control)
Description
Choice
Program code
Initial value
Available = 0
Not available = 1
:
;
Backlight
D4
D4
;
;
Always “0”
D3
D3
Significant
numbers
: :
; ;
Backlight off timer (01 ~ 59 min. “00” means always on.)
* This program is only effective for Eu.
D2 D1
D2 D1
50
Address code 36 (store/recall/auto new check number)
Description
Choice
Program code
Initial value
No = 0
Yes = 1
:
;
Reset the store/recall/auto new check starting number after open check reset report
D9
D9
Significant
numbers
; ; ; ;
: : : :
Store/recall/auto new check starting number (0000 = 0001) *
Store/recall/auto new check ending number (0000 = 9999) *
D8 D7 D6 D5
D8 D7 D6 D5
(0000 ~ 9999)
Significant
numbers
(0000 ~ 9999)
; ; ; ;
: : : :
D4 D3 D2 D1
D4 D3 D2 D1
* The starting number should be smaller than the ending number.
* If the starting number is bigger than the ending number, the E056 is occurred.
Address code 37 (check number)
Description
Choice
Program code
Initial value
Significant
numbers
(0000 ~ 9999)
; ; ; ;
: : : :
Auto check starting number (0000 = 0001) *
D8 D7 D6 D5
D8 D7 D6 D5
Significant
numbers
(0000 ~ 9999)
; ; ; ;
: : : :
Auto check ending number (0000 = 9999) *
D4 D3 D2 D1
D4 D3 D2 D1
* The starting number should be smaller than the ending number.
P
* If the starting number is bigger than the ending number, the E056 is occurred.
TE-2200/2400 Dealer's Manual
51
Key function/machine feature (P3)
Department key/flat-PLU key/PLU program (Batch feature programming)
Programming procedure
To another department/flat-PLU key
Department/flat-PLU key
Department
PGM
Mode switch
MENU
6 3s 6 B
6
:
~
:
6
6 s
SHIFT
Program data
Flat-PLU
(12 digits)
To a new (not sequential) PLU
PLU
Different program to the next PLU
PGM
Mode switch
6 3s 6
+6 : ~ : 6 a 6s
PLU No.
(Rec No. 4 digits)
Program data
(Random code 6 digits)
(12 digits)
Program data
Description
Choice
Program code
Initial value
;
Significant
number
:
Single item control:
Normal receipt = 0, Single item receipt = 3
D12
D12
Price change registration is enable.
No = 0
Yes = 1
a
b
c
(Only effective for scanning PLU linked to this department)
Multiplication registration is enable.
(Only effective for scanning PLU linked to this department)
No = 0
Yes = 2
;
:
(a+b+c)
D11
(a+b+c)
D11
Compulsory input unit price manually.
(Only effective for scanning PLU linked to this department)
No = 0
Yes = 4
Significant
number
;
Normal/condiment/preparation (Not for department)
Normal item = 0, Condiment = 1, Preparation = 2
:
D10
D10
No = 0
Yes = 1
a
Disable operation in RF/REG– mode.
Disable operation in REG 2 mode.
Disable operation in REG 1 mode.
No = 0
Yes = 2
b
;
:
(a+b+c)
D9
(a+b+c)
D9
No = 0
Yes = 4
c
Taxable status:
See the next page.
; ;
: :
D8 D7
D8 D7
No = 0
Yes = 1
Enable 0 unit price.
Enable negative price.
Hash
a
b
c
;
No = 0
Yes = 2
:
(a+b+c)
D6
(a+b+c)
D6
No = 0
Yes = 4
;
:
Always “0”
D5
D5
Significant
number
;
:
Low digit limitation (LDL) for manually entered unit price.
D4
D4
Multiple validation:
Yes = 0
No = 1
a
b
c
a
b
c
(If “No”, validation is allowed only one time.)
;
:
No = 0
Yes = 2
Print difference between the normal price and reduced price.
Open PLU (only for PLU)
(a+b+c)
D3
(a+b+c)
D3
No = 0
Yes = 4
No = 0
Yes = 1
Commission 1
No = 0
Yes = 2
;
:
Commission 2
(a+b+c)
D2
(a+b+c)
D2
Yes = 0
No = 4
Prepared tax status (Canadian tax)
Significant
number (0 ~ 8)
;
:
Compulsory number of condiment/preparation PLU input.
D1
D1
52
Taxable status
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D8
No = 0
Yes = 1
Taxable 1 status
a
b
c
:
No = 0
Yes = 2
Taxable 2 status
(a+b+c)
D7
No = 0
Yes = 4
Taxable 3 status
for Canada
No = 0
Yes = 1
:
Donuts status
D8
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
D7
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Significant
numbers
: :
D8 D7
P
TE-2200/2400 Dealer's Manual
53
Key function/machine feature (P3)
Department key/flat-PLU key/PLU program (Individual feature programming)
Programming procedure
Department/flat-PLU key
To another department/flat-PLU key
Same program
Department
PGM
Mode switch
~
6 3s6 : : 66s 6 : :
6
6 s
Flat-PLU
Program data
Address code
To a new (not sequential) PLU
PLU
Different program to the next PLU
Same program
PGM
Mode switch
PLU No.
6
3s
6
Address code
: :66s
6
+
6
: :
6
a
6
s
~
Program data
Range (Department/PLU/flat-PLU)
6
3s
6
990000 : :s
6
Address code
: : 66s6
PGM
Mode switch
Department
= 05
}
PLU/flat-PLU = 04
Ends “the last record”.
Starts “0001”.
6
: :
6
a
6
: :
6
a
6
: : a
6
~
~
~
s
Program data
Start rec-#
End rec-#
Program data (by address code)
Address code 11 (link)
Description
Choice
Program code
Significant
numbers
: :
Link group record number: (00 ~ 99)
D4 D3
Significant
numbers
Link department record number: (00 ~ 99)
(only for PLU)
: :
D2 D1
54
Address code 12 (random code)
Description
Choice
Program code
Significant
numbers
: : : : : :
PLU random code (only for PLU)
D6 D5 D4 D3 D2 D1
Address code 13 (set menu)
Description
Choice
Program code
Significant
numbers
: : : :
Set menu table/bottle link table record number (only for PLU)
D6 D5 D4 D3
Significant
numbers
Set menu table/bottle link table file number (only for PLU)
File number: set menu table = 28, bottle link table = 73
: :
D2 D1
Address code 14 (stock)
Description
Choice
Program code
Significant
numbers
Optimum stock quantity (0.001 ~ 99.999)
Enter without decimal point. (only for PLU)
: : : : :
D5 D4 D3 D2 D1
P
Address code 15 (high amount limit)
Description
Choice
Program code
Significant
numbers
: : : : : :
High amount limit for entering unit price manually.
D6 D5 D4 D3 D2 D1
Address code 16 (order control)
Description
Choice
Program code
: :
Significant
numbers
Order character record number (00 ~ 99)
D6 D5
Normal = 0
Reverse = 1
:
Printing color of order:
D4
No = 0
Yes = 1
a
b
c
Print order to “Order 1 (printer connection table)” printer.
Print order to “Order 2 (printer connection table)” printer.
Print order to “Order 3 (printer connection table)” printer.
Always “00”
:
No = 0
Yes = 2
(a+b+c)
D3
No = 0
Yes = 4
; ;
D2 D1
TE-2200/2400 Dealer's Manual
55
Key function/machine feature (P3)
Address code 17 (Bon receipt control)
Description
Choice
Program code
Significant
number
Number of Bon receipts (1 ~ 9)
(If “0”, no Bon is issued.)
:
D1
Other address code
Address
Description
code
Choice
Program code
Significant
number
Single item control:
Normal receipt = 0, Single item receipt = 3
18
:
No = 0
Yes = 1
Price change registration is enable.
a
b
c
(Only effective for scanning PLU linked to this department)
No = 0
Yes = 2
Multiplication registration is enable.
(Only effective for scanning PLU linked to this department)
:
19
(a+b+c)
No = 0
Yes = 4
Compulsory input unit price manually.
(Only effective for scanning PLU linked to this department)
Significant
number
Normal/condiment/preparation
Normal item = 0, Condiment = 1, Preparation = 2
01
:
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
No = 0
Yes = 2
:
02
Disable operation in REG 2 mode.
(a+b+c)
No = 0
Yes = 4
Disable operation in REG 1 mode.
Significant
numbers
Taxable status:
: :
03
05
See the status table of the batch feature programming section.
D2 D1
No = 0
Yes = 1
a
b
c
Enable 0 unit price.
Enable negative price.
Hash
No = 0
Yes = 2
:
(a+b+c)
No = 0
Yes = 4
Significant
number
Low digit limitation (LDL) for manually entered unit price.
07
04
:
Yes = 0
No = 1
Multiple validation:
(If “No”, validation is allowed only one time.)
a
b
c
a
b
c
No = 0
Yes = 2
Print difference between the normal price and reduced price.
Open PLU (Only for PLU)
:
(a+b+c)
No = 0
Yes = 4
No = 0
Yes = 1
Commission 1
No = 0
Yes = 2
Commission 2
09
10
:
(a+b+c)
Yes = 0
No = 4
Prepared tax status (Canadian tax)
Compulsory number of condiment/preparation PLU input.
Significant
number (0 ~ 8)
:
56
Transaction key program
Programming procedure
To another transaction key
PGM
Mode switch
Transaction
~
63s6 : :
6
6 s
key
Program data
Program data
<CASH>, <CHARGE>, <CHECK>
Description
Choice
Program code
No = 0
Yes = 1
Restriction (to 0, 5) on last digit for amount tendered.
(Only effective for <CHARGE> or <CHECK>)
:
D12
Significant number
(0 ~ 9)
:
Allowable number of validation printing (“0” means no limitation) *1 *2 *3 *4 *5
Force validation operation. *1 *2 *3 *4 *5
D11
No = 0
Yes = 1
a
b
a
b
c
a
b
c
a
b
c
a
b
c
:
(a+b)
D10
Restriction (to 00, 25, 50, 75) on last two digits for amount tendered
(Only for <CASH> in Danish rounding) *5
No = 0
Yes = 4
No = 0
Yes = 1
Disable operation in RF/REG– mode. *1 *4 *5
:
*1 *4 *5
No = 0
Yes = 2
Disable operation in REG2 mode.
(a+b+c)
D9
P
No = 0
Yes = 4
Disable operation in REG1 mode. *1 *4 *5
Force batch slip printing. *1 *2 *4
No = 0
Yes = 1
:
No = 0
Yes = 2
Force check endorsement printing (Only for <CHECK>). *3 *4 *5
Force check printing (Only for <CHECK>). *3 *4 *5
Prohibit entry of a partial payment
(a+b+c)
D8
No = 0
Yes = 4
No = 0
Yes = 1
:
No = 0
Yes = 2
Prohibit the entry of the amount tendered.
Force entry of the amount tendered.
(a+b+c)
D7
No = 0
Yes = 4
No = 0
Yes = 1
Print VAT breakdown. *1 *2 *4
Check cashing commission (Only for <CHECK>) *3
1Use an amount 2Use a rate
Validation amount *3 *4
1Print subtotal amount 2Print amount tendered
:
Amount = 0
Rate = 2
(a+b+c)
D6
Subtotal = 0
Tender = 4
No = 0
Yes = 4
:
Perform Finnish rounding.
D5
Maximum value
(0 ~ 9)
High amount limit specification for subtotal and tendering amounts. *3
: :
Number of zeros
(0 ~ 9)
D4 D3
Maximum value
(0 ~ 9)
High amount limit specification for change amount due.
: :
Number of zeros
(0 ~ 9)
D2 D1
*1 Those are valid options for Auto Cash as well.
*2 Those are valid options for Single item as well.
*3 Those are valid options for Cashing a check as well.
*4 Those are valid options for Currency exchange (include partial tender) as well.
*5 Those are valid options for Media change (include partial tender) as well.
TE-2200/2400 Dealer's Manual
57
Key function/machine feature (P3)
<CREDIT>
Description
Choice
Program code
No = 0
Yes = 1
:
Restriction (to 0, 5) on last digit for amount tendered.
D12
Significant number
(0 ~ 9)
:
Allowable number of validation printing (“0” means no limitation) *1
Force validation operation. *1
D11
No = 0
Yes = 1
:
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode. *1
Disable operation in REG2 mode. *1
Disable operation in REG1 mode. *1
Force batch slip printing.
a
b
c
No = 0
Yes = 2
:
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
D8
No = 0
Yes = 1
a
b
c
a
b
Prohibit entry of a partial payment
Prohibit the entry of the amount tendered.
Force entry of the amount tendered.
Print VAT breakdown.
:
No = 0
Yes = 2
(a+b+c)
D7
No = 0
Yes = 4
No = 0
Yes = 1
:
(a+b)
D6
Subtotal = 0
Tender = 4
Validation amount
1Print subtotal amount 2Print amount tendered
No = 0
Yes = 4
:
Perform Finnish rounding.
D5
Maximum value
(0 ~ 9)
High amount limit specification for subtotal and tendering amounts.
: :
Number of zeros
(0 ~ 9)
D4 D3
;
Always “0”
D2
Significant number
(0 ~ 4)
Specify credit in drawer total in the fixed totalizer. *1
:
D1
*1 Those are valid options for Media change (include partial tender) as well.
58
<FOOD STAMP TENDER>, <EBT>
Description
Choice
Program code
Significant number
(0 ~ 9)
:
Allowable number of validation printing (“0” means no limitation)
D11
No = 0
Yes = 1
:
Force validation operation.
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Force batch slip printing.
a
b
c
a
b
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
(a+b)
D8
No = 0
Yes = 4
Prohibit over tendering. (only for <EBT>)
;
Always “0”
D7
No = 0
Yes = 1
Print VAT breakdown.
a
:
(a+b)
D6
Subtotal = 0
Tender = 4
Validation amount
1Print subtotal amount 2Print amount tendered
b
;
Always “0”
D5
Maximum value
(0 ~ 9)
P
High amount limit specification for subtotal and tendering amounts.
: :
Number of zeros
(0 ~ 9)
D4 D3
; ;
Always “00”
D2 D1
<NEW BALANCE>
Description
Choice
Program code
Significant number
(0 ~ 9)
:
Allowable number of validation printing (“0” means no limitation)
D11
No = 0
Yes = 1
a
b
a
b
c
a
b
c
Force validation operation.
:
(a+b)
D10
No = 0
Yes = 4
Cancel the transaction if no item is registered.
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Force batch slip printing.
No = 0
Yes = 1
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
No = 0
Yes = 2
Open drawer when the key is pressed.
No receipt is issued.
(a+b)
D8
No = 0
Yes = 4
Significant
number
Function after normal (not in check tracking) registration:
Operation error = 0, Auto Cash = 1, New balance = 2
:
D7
No = 0
Yes = 1
Print VAT breakdown.
a
:
(a+b)
D6
Amount = 0
Rate = 2
Service charge
1Use an amount 2Use a rate
b
; ; ; ; ;
Always “00000”
D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
59
Key function/machine feature (P3)
<CHARACTER RECALL>, <CHARACTER PRINT>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
;
D8
No = 0
Yes = 1
Disable to change mode switch after registration.
(only effective for <character recall>)
a
:
(a+b)
D7
Yes = 0
No = 2
Print characters on receipt, guest receipt, or slip.
Always “0000”
b
; ; ; ;
D6 D5 D4 D3
; ;
Always “00”
D2 D1
<TIP>
Description
Choice
Program code
Yes = 0
No = 4
:
Multiple validation
(If “No”, only one validation printing is possible.)
D11
;
Always “0”
D10
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000”
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ;
D8 D7 D6 D5 D4
Significant
number
High digit limitation (HDL) for manually entered unit price
(“9” means NOT allow manual entry)
:
D3
; ;
Always “00”
D2 D1
60
<LOAN>, <PICK UP>
Description
Choice
Program code
:
No = 0
Yes = 1
Restriction (to 0, 5) on last digit for amount tendered.
Allowable number of validation printing (“0” means no limitation)
Force validation operation. (only effective after receipt issuance)
Disable operation in RF/REG– mode.
D12
Significant number
(0 ~ 9)
:
D11
No = 0
Yes = 1
:
D10
No = 0
Yes = 1
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
(a+b+c)
D9
No = 0
Yes = 4
Disable operation in REG1 mode.
; ; ; ;
Always “0000”
D8 D7 D6 D5
Maximum value
(0 ~ 9)
High amount limit specification for entering amounts
Always “00”
: :
Number of zeros
(0 ~ 9)
D4 D3
; ;
D2 D1
P
<RECEIVED ON ACCOUNT>, <PAID OUT>
Description
Choice
Program code
Significant number
(0 ~ 9)
:
Allowable number of validation printing (“0” means no limitation)
D11
No = 0
Yes = 1
:
Force validation operation.
D10
No = 0
Yes = 1
a
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0000”
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ;
D8 D7 D6 D5
Maximum value
(0 ~ 9)
High amount limit specification for entering amounts
: :
Number of zeros
(0 ~ 9)
D4 D3
; ;
Always “00”
D2 D1
These programmable options are not effective for the Euro function.
TE-2200/2400 Dealer's Manual
61
Key function/machine feature (P3)
<+ (PLUS)>, <- (MINUS)>, <COUPON>
Description
Choice
Program code
:
Yes = 0
No = 4
Multiple validation (If “No”, only one validation printing is possible.)
D11
;
Always “0”
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
: :
Taxable status:
See below.
D8 D7
No = 0
Yes = 1
:
Allow credit balance. (–, CPN only)
Always “0”
D6
;
D5
Yes = 0
No = 1
Allow key operation after <SUBTOTAL>.
Allow key operation after item registration.
a
:
(a+b)
D4
Yes = 0
No = 4
b
Significant
number
High digit limitation (HDL) for manually entered unit price
(“9” means NOT allow manual entry.)
:
D3
No = 0
Yes = 1
Commission 1
a
b
c
:
No = 0
Yes = 2
Commission 2
(a+b+c)
D2
Yes = 0
No = 4
Prepared tax status (Canadian tax)
Always “0”
;
D1
Taxable status
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D8
No = 0
Yes = 1
Taxable 1 status
Taxable 2 status
Taxable 3 status
a
:
No = 0
Yes = 2
(a+b+c)
D7
b
c
No = 0
Yes = 4
for Canada
No = 0
Yes = 1
:
Donuts status (D8D7=”99” means donuts and all taxable.)
D8
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
D7
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
All taxable = 99
Significant
numbers
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
: :
D8 D7
62
<DEPOSIT>
Description
Choice
Program code
:
No = 0
Yes = 1
Restriction (to 0, 5) on last digit for amount tendered.
D12
;
Always “0”
D11
No = 0
Yes = 1
Force validation operation.
a
b
a
b
c
(only effective after receipt issuance)
:
(a+b)
D10
No = 0
Yes = 4
Multiple validation (If “No,” only one validation is possible.)
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
No = 0
Yes = 1
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
;
D8
DEPO+ = 0
DEPO– = 1
:
Key attribution
D7
No = 0
Yes = 2
:
Open cash drawer.
D6
Media definition:
Cash = 0, Charge = 1, Check = 2,
Credit 1 = 3, Credit 2 = 4, Credit 3 = 5, Credit 4 = 6
Significant
number
:
P
D5
Maximum value
(0 ~ 9)
High amount limit specification for entering amounts
Always “00”
: :
Number of zeros
(0 ~ 9)
D4 D3
; ;
D2 D1
TE-2200/2400 Dealer's Manual
63
Key function/machine feature (P3)
<PREVIOUS BALANCE>
Description
Choice
Program code
:
Yes = 0
No = 4
Multiple validation (If “No”, only one validation printing is possible.)
D11
;
Always “0”
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
Taxable status:
See below.
: :
D8 D7
PB+ = 0
PB– = 1
Key attribution
a
:
(a+b)
D6
Yes = 0
No = 4
Print when registered.
Always “00”
b
; ;
D5 D4
Significant
number
:
High digit limitation (HDL) for manually entered unit price
(“9” means NOT allow manual entry.)
D3
Yes = 0
No = 4
:
Prepared tax status (Canadian tax)
Always “0”
D2
;
D1
Taxable status
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D8
No = 0
Yes = 1
Taxable 1 status
Taxable 2 status
Taxable 3 status
a
:
No = 0
Yes = 2
(a+b+c)
D7
b
c
No = 0
Yes = 4
for Canada
No = 0
Yes = 1
:
Donuts status (D8D7=”99” means donuts and all taxable.)
D8
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
:
Significant
number
Taxable 4 = 4
D7
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
All taxable = 99
Significant
numbers
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
: :
D8 D7
64
<PREMIUM (%+)>, <DISCOUNT (%-)>
Description
Choice
Program code
:
Yes = 0
No = 4
Multiple validation
(If “No”, only one validation printing is possible.)
D11
;
Always “0”
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
Taxable status:
See below.
: :
D8 D7
No = 0
Yes = 2
:
Prohibit manual rate override.
D6
Significant
number
Rounding:
Round off = 0, cut off = 1, round up = 2
:
D5
Yes = 0
No = 1
Allow key operation after <SUBTOTAL>.
Allow key operation after item registration.
Always “0”
a
:
(a+b)
D4
Yes = 0
No = 4
b
;
P
D3
No = 0
Yes = 1
Commission 1
a
b
c
No = 0
Yes = 2
:
Commission 2
(a+b+c)
D2
Yes = 0
No = 4
Prepared tax status (Canadian tax)
Always “0”
;
D1
Taxable status
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D8
No = 0
Yes = 1
Taxable 1 status
Taxable 2 status
Taxable 3 status
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D7
No = 0
Yes = 4
for Canada
No = 0
Yes = 1
:
Donuts status (D8D7=”99” means donuts and all taxable.)
D8
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
D7
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
All taxable = 99
Significant
numbers
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
: :
D8 D7
TE-2200/2400 Dealer's Manual
65
Key function/machine feature (P3)
<RATE TAX>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ;
D8 D7
No = 0
Yes = 2
:
Prohibit manual entry.
D6
Significant
number
Rounding:
Round off = 0, cut off = 1, round up = 2
:
D5
; ; ; ;
Always “0000”
D4 D3 D2 D1
<MANUAL TAX>
Description
Choice
Program code
Yes = 0
No = 4
:
Multiple validation
(If “No”, only one validation printing is possible.)
D11
;
Always “0”
D10
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000”
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ;
D8 D7 D6 D5 D4
Significant
number
High digit limitation (HDL) for manually entered unit price
(“9” means NOT allow manual entry.)
:
D3
; ;
Always “00”
D2 D1
<ERROR CORRECTION/CANCEL>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0000000”
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ; ; ;
D8 D7 D6 D5 D4 D3 D2
2= 0
1= 1
A range of cancellation:
1Complete cancellation/2Current receipt only
:
D1
These programmable options are not effective for error correction function.
66
<VOID>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0000000”
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ; ; ;
D8 D7 D6 D5 D4 D3 D2
A range of item correction:
1From the beginning of this transaction
2Current receipt only
2= 0
a
1= 1
:
(a+b)
D1
Yes = 0
No = 2
Affect stock quantity
b
<RECEIPT>
Description
Choice
Program code
:
Significant
number
Maximum number of post receipts (0 ~ 9)
(“0” means 1 post receipt.)
D12
P
; ;
Always “00”
D11 D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
a
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
;
D8
No = 0
Yes = 4
:
Print current time on guest receipt.
Clear finalized check.
D7
Yes = 0
No = 1
:
D6
;
Always “0”
D5
No = 0
Yes = 1
:
Print journal when receipt is issued by <RECEIPT>.
D4
Receipt is issued by:
Significant
number
•“Receipt 1 (printer connection table)” = 0
•“Receipt 2 (printer connection table)” = 1
•“Receipt 3 (printer connection table)” = 2
:
D3
Line number of guest bottom message (00 ~ 10):
(“00” means no bottom message.)
Significant
numbers
: :
D2 D1
TE-2200/2400 Dealer's Manual
67
Key function/machine feature (P3)
<CHECK ENDORSEMENT>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Significant
number
:
Line number of auto-back feed before printing (0 ~ 9)
Always “000000”
D7
; ; ; ; ; ;
D6 D5 D4 D3 D2 D1
<NON ADD (#)>, <NON ADD (#)/NO SALE>
Description
Choice
Program code
No = 0
Yes = 1
a
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
b
c
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Yes = 0
No = 1
Allow mode change or clerk change after non-add registration as first transaction.
(only for non-add function)
:
D7
; ; ; ;
Always “0000”
Always “00”
D6 D5 D4 D3
; ;
D2 D1
68
<CUSTOMER>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Significant
number
Input method:
:
Allow replacement = 0, Prohibit replacement = 1, Add enter value = 2
D7
; ; ; ; ; ;
Always “000000”
D6 D5 D4 D3 D2 D1
<ARRANGEMENT>
Description
Choice
Program code
P
: : : :
Significant
numbers
Secret code (0000 ~ 9999)
D14 D13 D12 D11
Yes = 0
No = 1
a
b
c
a
b
c
Enable operation in X1 mode.
Enable operation in Z1 mode.
Enable operation in X2/Z2 mode.
:
Yes = 0
No = 2
(a+b+c)
D10
Yes = 0
No = 4
Yes = 0
No = 1
Enable operation in RF/REG– mode.
Enable operation in REG2 mode.
Enable operation in REG1 mode.
Always “0”
:
Yes = 0
No = 2
(a+b+c)
D9
Yes = 0
No = 4
;
D8
No = 0
Yes = 1
:
Treat numeric entry as arrange table number
Arrangement table link number
D7
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
69
Key function/machine feature (P3)
<CURRENCY EXCHANGE>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Significant
number
:
Define amount symbol. (0, 1 ~ 4)
(“0” means local currency symbol.)
D7
Significant
number
Define foreign currency totalizer. (0, 1 ~ 4)
(“0” treats as “1”.)
:
D6
Significant
number
:
Rounding:
Round off = 0, cut off = 1, round up = 2
D5
;
Always “0”
D4
Significant
number
Monetary mode (0 ~ 9):
º00 = 2, º0 = 1, 0 = 0, º000 = 3
:
D3
Decimal = 0
Comma = 1
Monetary symbol for decimal
Monetary symbol for separator
a
:
(a+b)
D2
Comma = 0
Decimal = 4
b
Assigning drawer number: 0 ~ 2
(“0” means drawer 1.)
:
Significant
number (0 ~ 2)
D1
<BILL>
Description
Choice
Program code
No = 0
Yes = 1
a
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000”
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ;
D8 D7 D6 D5 D4
Receipt is issued by:
•“Receipt 1 (printer connection table)” = 0
•“Receipt 2 (printer connection table)” = 1
•“Receipt 3 (printer connection table)” = 2
Significant
number
:
D3
; ;
Always “00”
D2 D1
70
<SLIP>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
No = 0
Yes = 1
Force slip batch printing from the beginning of the transaction.
If “No”, controlled by general function.)
a
:
(a+b)
D7
No = 0
Yes = 4
Print issuing time
b
(only effective when slip is printed from the beginning of the transaction).
Yes = 0
No = 1
:
Clear finalized check.
Always “0”
D6
;
D5
No = 0
Yes = 1
:
Print journal when slip is printed.
Always “000”
D4
; ; ;
D3 D2 D1
P
<TAX SHIFT>, <TAXABLE SUBTOTAL>
Description
Choice
Program code
Maintain of tax shift:
1= 0
2= 1
:
1Do not maintain.
D7
2Until next tax shift specification.
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
a
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
Significant
numbers
Taxable status (00, 01 ~ 10)
(“00” means taxable 1.)
: :
D8 D7
; ; ; ; ; ;
Always “000000”
D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
71
Key function/machine feature (P3)
<EXEMPT>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
(a+b+c)
D9
No = 0
Yes = 4
Disable operation in REG1 mode.
• U.S., Singapore:
Yes = 0
No = 1
Exempt tax 1
a
b
c
;
D8
Yes = 0
No = 2
Exempt tax 2
:
(a+b+c)
D7
Yes = 0
No = 4
Exempt tax 3
• Canada:
Significant
number
Not exempt donuts tax = 0
Exempt donuts tax 1 = 1
:
D8
Exempt all (tax 1 ~ 4) = 0
Exempt tax 1 = 1,
Exempt tax 4 = 4,
Exempt tax 1 & 3 = 6,
Exempt tax 2 = 2,
Exempt tax 1 & 2 = 5,
Exempt tax 1 & 4 = 7
Exempt tax 3 = 3,
Significant
number
:
D7
• Other area
Exempt all (tax 1 ~ 10) = 00
Exempt tax 1 = 01,
Exempt tax 4 = 04,
Exempt tax 7 = 07,
Exempt tax 10 = 10
Exempt tax 2 = 02,
Exempt tax 3 = 03,
Exempt tax 6 = 06,
Exempt tax 9 = 09,
: :
Significant
numbers
Exempt tax 5 = 05,
Exempt tax 8 = 08,
D8 D7
No = 0
Yes = 1
:
Exempt add-in tax from subtotal amount.
Always “00000”
D6
; ; ; ; ;
D5 D4 D3 D2 D1
<MENU>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
a
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
;
Always “0”
D8
Significant
number
Define assigning menu sheet number. (0, 1 ~ 6)
(If you set “0”, menu sheets are assigned one by one.)
:
D7
; ; ; ; ; ;
Always “000000”
D6 D5 D4 D3 D2 D1
<OPEN>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
No = 0
Yes = 1
:
Release “High amount limit.”
Always “000000”
D7
; ; ; ; ; ;
D6 D5 D4 D3 D2 D1
72
<OPEN2>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Yes = 0
No = 1
a
b
c
a
b
c
a
b
c
a
b
Release customer number compulsory.
Release table number compulsory.
Release check number compulsory.
:
Yes = 0
No = 2
(a+b+c)
D7
Yes = 0
No = 4
Yes = 0
No = 1
Release credit balance error.
(If “Yes,” you can finalize the transaction even if the subtotal is negative.)
:
Yes = 0
No = 2
Release tax calculation compulsory before finalizing.
Release guest receipt compulsory.
(a+b+c)
D6
Yes = 0
No = 4
P
Yes = 0
No = 1
Release validation compulsory.
:
Yes = 0
No = 2
Release check endorsement compulsory.
Release check print compulsory.
(a+b+c)
D5
Yes = 0
No = 4
Yes = 0
No = 2
Release slip auto batch print compulsory. (programmed by clerk)
Release slip manual batch print compulsory. (programmed by finalize key)
Release condiment compulsory.
:
(a+b)
D4
Yes = 0
No = 4
Yes = 0
No = 1
:
D3
Yes = 0
No = 2
:
Release eat-in/takeout compulsory.
D2
;
Always “0”
D1
<PRICE SHIFT>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
b
c
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Significant
number
Define assigning price shift number. (0, 1 ~ 3)
(If you set “0”, price shift numbers are assigned one by one.)
:
D7
; ; ; ; ; ;
Always “000000”
D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
73
Key function/machine feature (P3)
<REVIEW>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
(a+b+c)
D9
No = 0
Yes = 4
The reviewed range of item:
1From the beginning of this transaction
2Current receipt only
2= 0
1= 1
:
(a+b)
D8
No = 0
Yes = 2
Display “Check number”, “Table number”, and “Customer number”.
Always “0000000”
; ; ; ; ; ; ;
D7 D6 D5 D4 D3 D2 D1
<CLERK NUMBER>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0000”
b
c
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ;
D8 D7 D6 D5
: : : :
Significant
numbers
Clerk secret number (0000 ~ 9999)
(“0000” means no secret number.)
D4 D3 D2 D1
<OPERATOR X/Z>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
;
D8
Standalone = 0
Consolidation = 1
:
Issue consolidation report./Issue stand-alone report.
Always “000000”
D7
; ; ; ; ; ;
D6 D5 D4 D3 D2 D1
74
<TRAY TOTAL>
Description
Choice
Program code
Allowable number of validation printing
(“0” means no limitation)
:
Significant number
(0 ~9)
D11
No = 0
Yes = 1
:
Force validation operation
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ;
D8 D7
Yes = 0
No = 1
Include add-on tax.
a
:
(a+b)
D6
No = 0
Yes = 4
Print tray total when <TRAY TOTAL> is pressed.
Always “00000”
b
; ; ; ; ;
D5 D4 D3 D2 D1
P
<SUBTOTAL>, <MERCHANDISE SUBTOTAL>
Description
Choice
Program code
Multiple validation
(If “No”, only one validation printing is possible.)
:
Yes = 0
No = 4
D11
:
Always “0”
D10
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ;
D8 D7
Yes = 0
No = 1
Include add-on tax. (<SUBTOTAL> only)
Print when key is pressed.
Always “00000”
a
:
(a+b)
D6
No = 0
Yes = 4
b
; ; ; ; ;
D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
75
Key function/machine feature (P3)
<MULTIPLICATION>, <QUANTITY/FOR>, <SQUARE>, <CUBE>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
; ;
D8 D7
1= 0
2= 1
Multiplication procedure: (<KETTEN BON> and <X> only)
1Quantity × Amount, 2Amount × Quantity
:
D6
Significant
number
Rounding:
Round off = 0, cut off = 1, round up = 2
:
D5
; ; ; ;
Always “0000”
D4 D3 D2 D1
<NEW CHECK>, <NEW/OLD CHECK>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0”
(a+b+c)
D9
No = 0
Yes = 4
;
D8
No = 0
Yes = 1
:
Enable auto check assignment
Always “000000”
D7
; ; ; ; ; ;
D6 D5 D4 D3 D2 D1
76
<PRICE CHANGE>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000”
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ;
D8 D7 D6 D5 D4
Significant
number
High digit limitation (HDL) for manually entered unit price
(“9” means NOT allow manual entry.)
:
D3
;
Always “0”
D2
No = 0
Yes = 1
a
Prohibit to change price greater than the preset price.
Prohibit to change price less than the preset price.
:
(a+b)
D1
No = 0
Yes = 2
b
P
<CLOCK-IN/OUT>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
(a+b+c)
D9
No = 0
Yes = 4
; ;
D8 D7
Significant
numbers
: :
High digit limitation (00 ~ 10), “00” means no limitation.
Always “00”
D6 D5
; ;
D4 D3
Usage:Both CLOCK-IN and CLOCK-OUT = 0,
CLOCK-IN only = 1, CLOCK-OUT only = 2
Significant
number
:
D2
Yes = 0
No = 1
:
Issue receipt during CLOCK-IN/OUT.
D1
TE-2200/2400 Dealer's Manual
77
Key function/machine feature (P3)
<EAT-IN>, <TAKEOUT>
Description
Choice
Program code
No = 0
Yes = 1
a
b
c
Disable operation in RF/REG– mode.
:
No = 0
Yes = 2
Disable operation in REG2 mode.
(a+b+c)
D9
No = 0
Yes = 4
Disable operation in REG1 mode.
• U.S., Singapore:
Yes = 0
No = 1
Exempt tax 1
a
b
c
;
D8
Yes = 0
No = 2
Exempt tax 2
:
(a+b+c)
D7
Yes = 0
No = 4
Exempt tax 3
• Canada:
Significant
number
Not exempt donuts tax = 0
Exempt donuts tax 1 = 1
:
D8
Exempt all (tax 1 ~ 4) = 0
Exempt tax 1 = 1,
Exempt tax 4 = 4,
Exempt tax 1 & 3 = 6,
Exempt tax 2 = 2,
Exempt tax 1 & 2 = 5,
Exempt tax 1 & 4 = 7
Exempt tax 3 = 3,
Significant
number
:
D7
• Other area
Exempt all (tax 1 ~ 10) = 00
Exempt tax 1 = 01,
Exempt tax 4 = 04,
Exempt tax 7 = 07,
Exempt tax 10 = 10
Exempt tax 2 = 02,
Exempt tax 3 = 03,
Exempt tax 6 = 06,
Exempt tax 9 = 09,
: :
Significant
numbers
Exempt tax 5 = 05,
Exempt tax 8 = 08,
D8 D7
No = 0
Yes = 1
Subtract add-in tax from subtotal amount.
(only subtracted when the tax is exempted.)
a
:
(a+b)
D6
No = 0
Yes = 4
Print when the key is pressed.
b
;
Always “0”
D5
Change tax status to: (only effective for VAT)
Significant
numbers
VAT 1 = 01, VAT 2 = 02, VAT 3 = 03, VAT 4 = 04, VAT 5 = 05,
VAT 6 = 06, VAT 7 = 07, VAT 8 = 08, VAT 9 = 09, VAT 10 = 10
(“00”: No change is made.)
: :
D4 D3
; ;
Always “00”
D2 D1
<ONE TOUCH NLU>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000”
b
c
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ;
D8 D7 D6 D5 D4
Significant
numbers
: : :
Linked one touch NLU record number (000 ~ 999)
D3 D2 D1
78
<CANCEL>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “0000000”
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ; ; ;
D8 D7 D6 D5 D4 D3 D2
A range of item correction:
1From the beginning of this transaction
2Current receipt only
2= 0
1= 1
:
D1
<VALIDATION>
Description
Choice
Program code
No = 0
Yes = 1
a
Disable operation in RF/REG– mode.
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00”
:
No = 0
Yes = 2
b
c
(a+b+c)
D9
No = 0
Yes = 4
P
; ;
D8 D7
Significant
number
Print total validation to:
Slip (paper is inserted in slip printer) or R/J = 0, Slip only = 1, R/J only = 2
:
D6
Significant
number
Number of copies by slip validation (0 ~ 9)
(“0” means 1 copy.)
:
D5
Significant
numbers
: :
Number of auto feed lines between slip validation printing (00 ~ 99)
Number of line feeds before slip validation (00 ~ 99)
D4 D3
Significant
numbers
: :
D2 D1
<PRICE INQUIRY>, <STOCK INQUIRY>, <CHECK PRINT>, <REFUND>, <COUPON2>,
<NO SALE>, <VAT>, <PLU>, <PRICE>, <BOTTLE RETURN>,
<SLIP BACKFEED/RELEASE>, <SLIP FEED/RELEASE>, <TABLE NUMBER>,
<FOOD STAMP SHIFT>, <RED PRICE>, <DECLARATION>, <RECEIPT ON/OFF>,
<PREVIOUS BALANCE SUBTOTAL>, <FOOD STAMP SUBTOTAL>, <OLD CHECK>,
<ADD CHECK>, <SEPARATE CHECK>, <OBR>, <OPEN CHECK>, <MEDIA CHANGE>, <STORE>,
<RECALL>
Description
Choice
Program code
No = 0
Yes = 1
Disable operation in RF/REG– mode.
a
b
c
:
No = 0
Yes = 2
Disable operation in REG2 mode.
Disable operation in REG1 mode.
Always “00000000”
(a+b+c)
D9
No = 0
Yes = 4
; ; ; ; ; ; ; ;
D8 D7 D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
79
Key function/machine feature (P3)
Clerk program
Secret number, drawer, check number programming
Programming procedure
To a new (not sequential) clerk
To the next clerk
63s 6 : : 07s6 : : : : 6 a 6 s
~
PGM
Mode switch
D12 D11 ~ D2 D1
Record No.
Data
Description
Choice
Program code
Significant
numbers
: : : : : :
Check number for clerk interrupt
D12 D11 D10 D9 D8 D7
Significant
numbers
Assigning drawer number: 00 ~ 02
("00" means drawer 1.)
: :
D6 D5
Significant
numbers
: : : :
Clerk secret number
D4 D3 D2 D1
To a new (not sequential) total
Clerk detail link programming
Programming procedure
aTo the next total
Department
PGM
MENU
Transaction
{ }
Flat-PLU
63s 6 : :30s 66 B
6 s
Mode
switch
Record No.
Scanning
*
File No.
OBR
B
Scanning code
PRICE
Fixed totalizer:
01
6 B 6
6
SHIFT
}
{
Transaction key: 02
PLU No.
+
PLU:
Department:
Group:
04
05
06
6
: : : : : : a 6
Record No.
* File No.
80
Clerk other programming
Programming procedure (individual)
To a new (not sequential) clerk
To the next clerk
6 3s 6 : : 07s6 : : s 6 : ~ : a 6 s
PGM
Mode switch
Record No.
Address code
Program data
Programming procedure (by range)
6
3s
6
99000007s
6
: : s6
PGM
Mode switch
Address code
Ends “the last record”.
Starts “0001”.
6
: :
6
a
6
:
:
6
a
6
:
: a
6
s
~
~
~
Start rec-#
Program data
End rec-#
Program data
Address code 67 (Clerk control)
P
Description
Choice
Program code
No = 0
Yes = 4
:
Check number compulsory
Table number compulsory
Number of customer compulsory
D10
No = 0
Yes = 1
a
b
c
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D9
No = 0
Yes = 4
Guest receipt compulsory (at finalization)
Guest receipt compulsory (at new balance)
Slip auto-batch print compulsory (at finalization)
Slip auto-batch print compulsory (at new balance)
No = 0
Yes = 1
:
No = 0
Yes = 2
(a+b+c)
D8
No = 0
Yes = 4
Significant
number
Clerk attribution:
Cashier = 0, Clerk = 1, Manager = 2
:
D7
No = 0
Yes = 1
Training clerk
a
b
a
b
c
:
(a+b)
D6
No = 0
Yes = 4
Affect stock quantity even if assigning a training clerk
Enable to open clerk created by other clerk
Disable to sign on
No = 0
Yes = 1
:
No = 0
Yes = 2
(a+b+c)
D5
No = 0
Yes = 4
Sign off at finalization (secret number only)
Always “0”
;
D4
No = 0
Yes = 2
:
Compulsory Eat-in/Takeout operation
Always “00”
D3
; ;
D2 D1
TE-2200/2400 Dealer's Manual
81
Key function/machine feature (P3)
Address code 68 (Commission rate)
Description
Choice
Program code
Significant
numbers
: :
Commission rate 1 (integer: 00 ~ 99)
D8 D7
Significant
numbers
: :
Commission rate 1 (decimal: 00 ~ 99)
Commission rate 2 (integer: 00 ~ 99)
Commission rate 2 (decimal: 00 ~ 99)
D6 D5
Significant
numbers
: :
D4 D3
Significant
numbers
: :
D2 D1
Address code 69 (Table number range)
Description
Choice
Program code
Minimum range for table range (1 ~ 999999)
(“0” means no programming.)
Significant
numbers
: : : : : :
D12 D11 D10 D9 D8 D7
Maximum range for table range (1 ~ 999999)
(“0” means no programming.)
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
Address code 70 (Mode control)
Description
Choice
No = 0
Yes = 1
Program code
a
b
c
a
b
c
Disable to operate in PGM mode.
No = 0
Yes = 2
No = 0
Yes = 4
No = 0
Yes = 1
No = 0
Yes = 2
:
Disable to operate in RF/REG– mode.
Disable to operate in REG1 mode.
Disable to operate in REG2 mode.
Disable to operate in X1 mode.
Disable to operate in Z1 mode.
(a+b+c)
D10
:
(a+b+c)
D9
No = 0
Yes = 4
No = 0
Yes = 1
:
Disable to operate in X2/Z2 mode.
Always “0”
D8
;
D7
Yes = 0
No = 1
Yes = 0
No = 2
Yes = 0
No = 1
Yes = 0
No = 4
Yes = 0
No = 1
Yes = 0
No = 2
Yes = 0
No = 4
a
b
a
b
a
b
c
Enable to finalize a transaction if the clerk is assigned by clerk key.
:
(a+b)
D6
Enable to finalize a transaction if the clerk is assigned by clerk code/switch.
Skip programming fields of batch/direct PLU maintenance file in
accordance with the general function program (address code 32, 33).
:
(a+b)
D5
Enable to issue individual key reset report.
Enable to issue read/reset report by file.
Enable to issue batch read/reset report.
Enable to issue operator reset report.
:
(a+b+c)
D4
Significant
number
:
Default menu sheet number (0 ~ 6) after signing on.
D3
Yes = 0
No = 1
Yes = 0
No = 2
Yes = 0
No = 4
Yes = 0
No = 1
Yes = 0
No = 2
Yes = 0
No = 4
Enable to use 1st menu sheet.
Enable to use 2nd menu sheet.
Enable to use 3rd menu sheet.
Enable to use 4th menu sheet.
Enable to use 5th menu sheet.
Enable to use 6th menu sheet.
a
b
c
a
b
c
:
(a+b+c)
D2
:
(a+b+c)
D1
82
Other programs
Time range programming
Programming procedure
To a new (not sequential) record
To the next record
6 3s 6 : : 09s6
:
~
:
6 a 6 s
PGM
Mode switch
Program data
Record No.
Program data
Description
Choice
Program code
Significant
numbers
: :
Start time (hour: 00 ~ 23)
D8 D7
Significant
numbers
: :
Start time (minute: 00 ~ 59)
End time (hour: 00 ~ 23)
End time (minute: 00 ~ 59)
D6 D5
Significant
numbers
: :
D4 D3
Significant
numbers
: :
og
D2 D1
P
Table range programming
Programming procedure
To a new (not sequential) record
To the next record
6 3s6 : : 18s6 :
~
: 6 a 6 s
PGM
Mode switch
Program data
Record No.
Program data
Description
Choice
Program code
Minimum check number (000000 ~ 999999)
(“0” means “000001.”)
Significant
numbers
: : : : : :
D12 D11 D10 D9 D8 D7
Maximum check number (000000 ~ 999999)
(“0” means no programming.)
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
TE-2200/2400 Dealer's Manual
83
Key function/machine feature (P3)
Tax table programming
Programming procedure
PGM
(for the U.S., Singapore)
Mode switch
Tax table 1 = 0125
Tax table 2 = 0225
Tax table 3 = 0325
8
3s
8
: : : :
8
{
(for other area)
(for Canada)
Tax table 1 = 0125
Tax table 2 = 0225
Tax table 1
Tax table 2
:
=
=
=
0125
0225
:
{
s
Tax table 3 = 0325
Tax table 4 = 0425
{
Tax table 10 = 1025
: :
^
: : : :
a
Tax rate (4-digit for integer + 4-digit for decimal)
Tax table maximum value (“0” means unlimited).
Rounding/tax table system code *1
8
: : : :
a
a
a
a
a
8
D
D
D
D
1
: : : :
4
3
2
8
: : : :
8
: : : :
8
Sum of a cyclic pattern
Number of values in each cyclic pattern
Sum of values in each non-cyclic pattern
: : : :
8
: : : :
8
Actual value of difference of the non-cyclic and cyclic values
You must enter these values in 4-digit block. If the last block
comes out to be only two digits, add two zeros.
a
Loop to input the next block.
s
Tax system code specification
D2 D1
Rounding
*1 Rounding/Tax system code
Rounding code specification
4
-- Singapore rounding
--
--
--
--
--
--
1
2
3
4
6
7
Tax table only
D4 D3
Rounding
U.S. tax table with tax rate or add-on tax only
Add-in tax rate
5
9
0
0
0
0
Rounding off two decimal places
Rounding up to two decimal places
Cut off two decimal places
Tax-on-tax (Canada, Singapore)
VAT-on-tax (Thailand)
VAT & VAT_2
Canadian tax system
For both add-on and add-in tax systems.
To program Tax-on-tax system, you must use the tax address “0225”, “0325” or “0425.”
To program Donuts tax system, you must use the tax address “0125” or “0225.”
84
Example 1:
Add-on rate tax
Tax rate (2-digit for integer + 4-digit for decimal) ............................... 8.25%
Tax table maximum value ("0" means unlimited). ............................... 0 (no limitation)
Rounding/tax table system code ........................................................... 5002 (Round off)
Sum of a cyclic pattern ......................................................................... 0
Number of values in each cyclic pattern ............................................... 0
Number of values in each non-cyclic pattern ....................................... 0
Actual value of difference of the non-cyclic and cyclic values ............ 0
No need to enter.
}
3s
PGM
Mode switch
8
Tax table No. (0125 ~ 1025)
: : : :
s
8
Tax rate (2-digit for integer + 4-digit for decimal)
Tax table maximum value (“0” means unlimited).
Rounding/tax table system code
8^25a
8
0a
8
og
5002a
P
8
s
TE-2200/2400 Dealer's Manual
85
Key function/machine feature (P3)
Example 2:
U.S. tax table without rate setting
Max. break point
Upper Lower
TAX
Price range
Difference
Pattern
Non cyclic
Cyclic
(6%) Min. break point Max. break point
10
24
–
–
–
–
–
–
–
0
10
24
41
58
74
91
=
=
=
=
=
=
=
=
=
10
14
17
17
16
17
17
16
17
17
$ .00
.01
.02
.03
.04
.05
.06
.07
.08
$ .01
.11
$ .10
.24
41
.25
.41
58
.42
.58
74
.59
.74
91
.75
.91
108
Cyclic
Cyclic
.92
1.08
1.24
1.41
124 – 108
141 – 124
1.09
1.25
Tax rate (2-digit for integer + 4-digit for decimal) ............................... 0 %(Table only)
Tax table maximum value (“0” means unlimited). ............................... (Table only)
0
Rounding/tax table system code ........................................................... 01 (Table only)
Sum of a cyclic pattern ......................................................................... 50 (17+17+16)
Number of values in each cyclic pattern ...............................................
3
Number of values in each non-cyclic pattern ....................................... 24 (10+14)
Actual value of difference of the non-cyclic and cyclic values ............ 10, 14, 17, 17, 16
3s
8
PGM
Mode switch
: : : :
s
Tax table No. (0125 ~ 0325)
8
0a
8
Tax rate (2-digit for integer + 4-digit for decimal)
Tax table maximum value (“0” means unlimited).
Rounding/tax table system code
0a
8
01a
8
50a
Sum of a cyclic pattern
8
3a
Number of values in each cyclic pattern
Sum of values in each non-cyclic pattern
8
24a
8
1014a
8
1717a
Actual value of difference of the non-cyclic and cyclic values.
8
1600a
8
You must enter these values in 4-digit block. If the last block
comes out to be only two digits, add two zeros.
s
86
Example 3:
U.S. tax table with rate setting
Max. break point
Upper Lower
TAX
Price range
Difference
Pattern
(7%) Min. break point Max. break point
7
21
–
–
–
–
–
–
–
–
0
7
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
7
14
14
14
15
14
14
15
14
14
14
15
14
14
15
Non-cyclic
$ .00
.01
.02
.03
.04
.05
.06
.07
.08
.09
.10
.11
.12
.13
.14
$ .01
.08
$ .07
.21
35
21
35
49
64
78
92
.22
.35
49
.36
.49
64
Cyclic
Cyclic
.50
.64
78
.65
.78
92
.79
.92
107
.93
1.07
1.21
1.35
1.49
1.64
1.78
1.92
2.07
121 – 107
135 – 121
149 – 135
164 – 149
178 – 164
192 – 178
207 – 192
1.08
1.22
1.36
1.50
1.65
1.79
1.93
1.40
19.93
20.07
One all sales above $20.07, compute the tax
at the rate of 7%.
Tax rate (2-digit for integer + 4-digit for decimal) ...............................
7 %
og
Tax table maximum value (“0” means unlimited). ............................... 2007
P
Rounding/tax table system code ........................................................... 0002 (Cut off & table + rate)
Sum of a cyclic pattern ......................................................................... 100 (14+14+14+15+14+14+15)
Number of values in each cyclic pattern ...............................................
Number of values in each non-cyclic pattern .......................................
7
7
Actual value of difference of the non-cyclic and cyclic values ............ 14, 14, 14, 15, 14, 14, 15
3s
8
PGM
Mode switch
Tax table No. (0125 ~ 0325)
: : : :
s
8
7a
8
Tax rate (2-digit for integer + 4-digit for decimal)
Tax table maximum value (“0” means unlimited).
Rounding/tax table system code
2007a
8
0002a
8
Sum of a cyclic pattern
100a
8
Number of values in each cyclic pattern
7a
8
7a
Sum of values in each non-cyclic pattern
8
0714a
8
1414a
Actual value of difference of the non-cyclic and cyclic values.
8
1514a
8
1415a
You must enter these values in 4-digit block. If the last block
comes out to be only two digits, add two zeros.
8
s
TE-2200/2400 Dealer's Manual
87
Key function/machine feature (P3)
Example 4:
Add-in rate tax
Tax rate (2-digit for integer + 4-digit for decimal) ............................... 10.00 %
Rounding/tax table system code. .......................................................... 0003 (Cut off)
3s
8
PGM
Mode switch
Tax table No. (0125 ~ 0325)
: : : :
s
8
Tax rate (2-digit for integer + 4-digit for decimal)
Always “0”
10a
8
0a
8
Rounding/tax table system code
0003a
8
s
Example 5:
Singapore tax
Tax table 1
Tax table 2
Tax table 3
Country tax .............................................................. 1%
Round off/tax on tax................................................ 5044
Service charge ......................................................... 10%
Round off/tax on tax................................................ 5044
PGM
Mode switch
GST .........................................................................
3%
Round off ................................................................ 5002
Tax table 1
Tax table 2
Tax table 3
3s
3s
3s
8
8
0225s
8
8
0125s
0325s
8
8
Tax rate
1a
10a
3a
(4-digit for integer + 4-digit for decimal)
8
8
0a
8
8
Always “0”
0a
0a
8
8
Rounding/tax table system code
5044a
5044a
5002a
8
8
8
s
s
s
88
Set menu programming
Programming procedure
To a new (not sequential) record
To the next record
a
Maximum 15 items can be set.
MENU
SHIFT
Flat-
B
6
B
PLU
63s6 : : 28s 6
6 s
PGM
Mode switch
{
}
: ~ : 6 +
PLU code
Record No.
Rec #: within 4 digits
Random code: within 6 digits
Batch X/Z report programming
Programming procedure
To a new (not sequential) record
To the next record
a
1st to 11th field
6 3s 6 : : 29s6 :
~
: 6 a 6 s
PGM
Mode switch
og
P
Program data
Record No.
Program data
Control flag (1st field)
Description
Choice
Program code
No = 0
Yes = 1
Save X data to CF card.
a
b
c
:
No = 0
Yes = 2
Save Z data to CF card.
(a+b+c)
D4
No = 0
Yes = 4
Issue report, in case of saving data to CF card.
;
Always “0”
D3
No = 0
Yes = 1
a
b
c
Disable operation in X1 mode.
Disable operation in Z1 mode.
:
No = 0
Yes = 2
(a+b+c)
D2
No = 0
Yes = 4
Disable operation in X2/Z2 mode.
Report contents in the X2/Z2 mode:
• Read report of periodic total 1 = 0
• Read report of periodic total 2 = 2
Significant
number
:
• Reset report of periodic total 1 = 1
• Reset report of periodic total 2 = 3
D1
Report code (2nd ~ 11th field)
Description
Choice
Program code
Report code:
Fixed totalizer = 11, Transaction key = 12, PLU = 14, PLU by group = 24,
Department = 15, Group = 16, Clerk = 17, Time zone = 19, Monthly = 20,
Scanning PLU = 26, Table analysis = 28, Employee = 29, Mix & match = 61,
PLU stock = 64, PLU stock by group = 34
Significant
numbers
: :
D2 D1
TE-2200/2400 Dealer's Manual
89
Key function/machine feature (P3)
Arrangement programming
Programming procedure
**
*
~
~
63s 6 : : 38s6 A6 : : a 6
PGM
Mode switch
Arrangement table No. (up to 6 digits)
Record No.
(up to 4 digits)
*
~
6
: : 6 A 6 s
Key operations
* The same A should be pressed.
** Vacant record search: If you want to set an arrangement program to a new record, “vacant record search”
is possible. (enter 0000 instead of entering a record No.)
Check print control programming
Programming procedure
To a new (not sequential) record
To the next record
~
6 3s 6 : : 41s6 : : 6a 6 s
PGM
Mode switch
Program data
Record No.
Program data
Description
Choice
Program code
Define printing data:
1: Printing amount, 2: Printing amount (double size),
Significant
number
:
3: Printing date, 4: Printing date (double size)
5: Check endorsement message 1st line, 6: Check endorsement message 2nd line,
7: Check endorsement message 3rd line, 8: Check endorsement message 4th line
D5
No = 0
Yes = 1
Feed before printing.
a
b
c
:
Normal = 0
Reverse = 2
Feed direction
(a+b+c)
D4
No = 0
Yes = 4
Feed one line after printing. *
No. of feed lines before printing (0 ~ 9)
Significant
number
:
D3
Significant
numbers
: :
Printing offset digits (00 ~ 39)
D2 D1
* If you set “0” to this option, one line back feed is made automatically.
90
Mix & match programming
Programming procedure
To a new (not sequential) record
To the next record a
6 3s6 : : 51s6
PGM
Mode switch
Record No.
6 :
~
: a 6 : : a 6 s
~
Program data
(1st field)
Program data
(2nd field)
Program data
Description
Choice
Program code
• Amount (1st field)
Discount amount
• Flag (2nd field)
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
og
: :
Taxable status (see below)
P
D6 D5
;
Always “0”
D4
Mix & match type*:
Discount 1 = 0: Discount every required quantity
Discount 2 = 1: Discount once
:
Significant
number
D3
Discount 3 = 2: Discount continuously
Significant
numbers
: :
Mix & match required quantity
D2 D1
* Example: (item unit price = $3.00, required quantity = 3, discount amount = $0.50)
• Discount 1: $3.00, $3.00, $2.50, $3.00, $3.00, $2.50, $3.00, $3.00, $2.50 ...
• Discount 2: $3.00, $3.00, $2.50, $3.00, $3.00, $3.00, $3.00, $3.00, $3.00 ...
• Discount 3: $3.00, $3.00, $2.50, $2.50, $2.50, $2.50, $2.50, $2.50, $2.50 ...
Taxable status
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D6
No = 0
Yes = 1
Taxable 1 status
Taxable 2 status
Taxable 3 status
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D5
No = 0
Yes = 4
for Canada
No = 0
Yes = 1
:
Donuts status (D8D7=”99” means donuts and all taxable.)
D6
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
D5
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
All taxable = 99
Significant
numbers
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
: :
D6 D5
TE-2200/2400 Dealer's Manual
91
Key function/machine feature (P3)
Employee number programming
Programming procedure
To a new (not sequential) record
To the next record
6 3s 6 : : 61s6 : : 6a 6 s
~
PGM
Mode switch
Program data
Record No.
Program data
Description
Choice
Program code
Significant
numbers
: : ~ : :
Employee number (0000000001 ~ 9999999999)
D10 D9
D2 D1
92
Scheduler programming
Programming procedure
6 3s6 : : 62s6 : ~ : 6 a 6
PGM
Mode switch
Record No.
Program data 1
To the next record
To new record
6
: ~ : 6 a 6
:
~
:
6a 6s
Program data 2
Program data 3
Program data 1
Description
Choice
Program code
Significant
numbers
Designate clerk by record number
(“00” means the first record.)
: :
D6 D5
Significant
number
Scheduler type 1:
Execute one time = 0, Execute every day = 1, Execute every week = 2
:
D4
Scheduler type 2:
Execute even if the cash register is in the OFF mode = 0,
Not execute if the cash register is in the OFF mode = 1
Significant
number
:
D3
Significant
number
Execute kind:
:
Switch menu shift/price shift = 0, Arrangement = 1, Job command = 2
D2
og
Yes = 0
No = 1
:
Wait until the drawer (compulsory drawer) is closed.
D1
P
Program data 2
Description
Choice
Program code
• Execute kind: Switch menu shift/price shift
Significant
number
:
Switch to: 1st menu sheet = 1, 2nd menu sheet = 2, 3rd menu sheet = 3,
4th menu sheet = 4, 5th menu sheet = 5, 6th menu sheet = 6, No change = 0
D2
Significant
number
Switch to:
:
1st price = 1, 2nd price = 2, 3rd price = 3, No change = 0
D1
• Execute kind: Arrangement
Arrangement table record No.
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
• Execute kind: Job command * Refer to the “Job command” table.
Job command No.
Significant
numbers
: : : : : :
D14 D13 D12 D11 D10 D9
; ;
Always “00”
D8 D7
;
Always “0”
D6
Significant
numbers
: : : : :
Job command parameter
D5 D4 D3 D2 D1
Program data 3
Description
Choice
Program code
Significant
numbers
: :
Execute year (00 ~ 99; means 2000 ~ 2099)
D10 D9
Significant
numbers
: :
Execute month (01 ~ 12, “00” means no programming)
D8 D7
Execute day or execute day of a week:
Significant
numbers
Day (01 ~ 31 “00” means no programming)
: :
(Day of a week; Sunday = 00, Monday = 01, Tuesday = 02, Wednesday = 03,
Thursday = 04, Friday = 05, Saturday = 06)
D6 D5
Significant
numbers
: :
Execute hour (00 ~ 23)
D4 D3
Significant
numbers
: :
Execute minute (00 ~ 59)
D2 D1
TE-2200/2400 Dealer's Manual
93
Key function/machine feature (P3)
Job command table
Description
Job No.
Group/terminal ID
Parameter
Default menu sheet number after signing on. (D3 of address code 70 of clerk programming)
030770
030771
200107
074070
070270
070070
070020
070030
00
0cddee
Disabled menu sheet number (D2D1 of address code 70 of clerk programming)
Switching to dual (Euro/local) currency system to Euro only system
Batch maintenance activation
00
00
00
00
00
00
00
fgddee
002002
000000
000000
Format CF card
000ppp
ppp:command code
Save programming data to CF card.
000ppp
ppp:command code
Load programming data from CF card.
Delete file in CF card.
000ppp
ppp:command code
c: Input default menu sheet number (0 ~ 6). (This automatically changes the D3 value of address 70 of clerk programming by job command.)
f: Program restrictive status of menu sheet 1 ~ 3. (This automatically changes the D2 value of address 70 of clerk programming by job command.)
g: Program restrictive status of menu sheet 4 ~ 6. (This automatically changes the D1 value of address 70 of clerk programming by job command.)
dd: Input the start record number of clerk.
ee: Input the end record number of clerk.
94
Bottle link table programming
Programming procedure
To a new (not sequential) total
To the next record
6 3s 6 : : 73s6
PGM
Mode switch
Record No.
Flat-
PLU
MENU
6 6
6
B
6
B
6 a 6 s
PLU No.
+ 6
6
: : : : 04a6
Record No. (4-digits)
Random code (6-digits)
og
P
TE-2200/2400 Dealer's Manual
95
Key function/machine feature (P3)
I/O parameter table programming
Programming procedure
To a new record
To the next record
~
63s 6 : : 98s6 : : 6 a6 s
PGM
Mode switch
Program data
Record No.
Note: Please perform the following procedure after this program.
1. Power off the register, and connect all peripheral devices to COM ports.
2. Power on all peripheral devices.
3. Flag clear the register.
Program data (Address 01: for COM 1 port)
Description
Choice
Program code
International character set number for external printer:
00: U.S.A., 01: France, 02: German, 03: U.K., 04: Denmark(1), 05: Sweden,
06: Italy, 07: Spain(1), 09: Norway, 10: Denmark(2)
Significant
numbers
: :
D16 D15
International character set page number for external printer:
0000: Multilingual + Euro, 0002: Multilingual, 0003: Portuguese,
0004: Canadian French, 0005: Nordic
Significant
numbers
: : : :
D14 D13 D12 D11
; ; ; ;
Always“0000”
D10 D9 D8 D7
Significant
numbers
External printer:
UP-360 = 00
: :
D6 D5
Connected device:
Significant
numbers
PC/ECR direct connection = 00, MODEM = 30,
External printer (as external printer 1 in printer connection table) = 80,
External printer (as external printer 2 in printer connection table) = 81
: :
D4 D3
Significant
number
Baud rate:
Refer to the baud rate/device table.
:
D2
;
Always“0”
D1
Program data (Address 02: for COM 2 port)
Description
Choice
Program code
International character set number for external/slip printer:
00: U.S.A., 01: France, 02: German, 03: U.K., 04: Denmark(1), 05: Sweden,
06: Italy, 07: Spain(1), 09: Norway, 10: Denmark(2)
Significant
numbers
: :
D16 D15
International character set page number for external/slip printer:
For SP-1300:
0000: Multilingual + Euro, 0002: Multilingual, 0003: Portuguese,
0004: Canadian French, 0005: Nordic, 0006: Slavic, 0007: Cyrillic,
0008: Turkish, 0009: Windows code page
Significant
numbers
: : : :
D14 D13 D12 D11
For UP-360:
0000: Multilingual + Euro, 0002: Multilingual, 0003: Portuguese,
0004: Canadian French, 0005: Nordic
; ; ; ;
Always“0000”
D10 D9 D8 D7
External printer/slip printer/scanner:
Significant
numbers
• External printer (D4D = 80, 81): UP-360 = 00
: :
• Slip printer (D D = 730): SP-1300 = 00
D6 D5
• Scanner (D4D34= 320): HHS-15 = 00, Quick Scan 6000 = 01
Connected device:
: :
Scanner = 20, Slip printer = 70,
Significant
numbers
External printer (as external printer 1 in printer connection table) = 80,
External printer (as external printer 2 in printer connection table) = 81
D4 D3
Significant
number
Baud rate:
Refer to the baud rate/device table.
:
D2
;
Always“0”
D1
96
Reference (Baud rate/device table)
Device
Default baud rate
Other selection
Scanner (HHS-15)
2400bps (D2 = 0)
9600bps (D2 = 2)
4800bps (D2 = 3)
2400bps (D2 = 4)
Scanner (Quick Scan 6000) 9600bps (D2 = 0)
4800bps (D2 = 3)
19200bps (D2 = 1)
None
External printer (UP-360)
Slip printer (SP-1300)
MODEM
9600bps (D2 = 0)
9600bps (D2 = 0)
19200bps (D2 = 0)
9600bps (D2 = 2)
None
4800bps (D2 = 3)
PC/ECR direct connection 19200bps (D2 = 0)
Printer connection table programming
Programming procedure
To a new record
To the next record
63s 6 : : 93s6 : ~ : 6 a6 s
PGM
Mode switch
og
Program data
Record No.
P
Program data
Description
Choice
Program code
Printout type:
Significant
numbers
: :
Receipt (1) = 00, Receipt (2) = 01, Receipt (3) = 02, Report = 10
Order (1) =20, Order (2) = 21, Order (3) = 22
D10 D9
; ;
Always “00”
D8 D7
Significant
numbers
Printout destination (Main):
R/J printer = 00, External printer 1 = 01, External printer 2 = 02
: :
D6 D5
; ;
Always “00”
D4 D3
Significant
numbers
Printout destination (Backup):
R/J printer = 00, External printer 1 = 01, External printer 2 = 02
: :
D2 D1
TE-2200/2400 Dealer's Manual
97
Key function/machine feature (P3)
Non PLU table programming
To a new record
Programming procedure
To the next record
~
63s 6 : : 40s6 : : 6 a6 s
PGM
Mode switch
Program data
Record No.
Program data
Description
Choice
Program code
Significant
number
:
Non PLU type: Short version = 0, Long version = 1
Price check digit is included in the price field.
Price × 10 n
D16
No = 0
Yes = 1
:
D15
Significant
number
:
D14
Significant
number
:
Number of digits for price
D13
; ; ; ; ; ; ;
Always “0000000”
D12 D11 D10 D9 D8 D7 D6
Significant
number
:
Number of digits for scanning PLU search code
D5
Flag code:
Number of digits for flag (1 ~ 3)
Significant
number
:
D4
Flag code:
Actual value
Significant
numbers
: : :
D3 D2 D1
Program sample
• Long version barcode (with price check digit)
F1
F2
I1
I2
I3
I4
I5
P/C P1
P2
P3
P4
P4 C/D
Flag
Item code
Price check digit
Price
Check digit
Program code: 1005000000072F1F20
• Long version barcode (without price check digit)
F1
F2
F3
I1
I2
I3
I4
P1
P2
P3
P5 C/D
Flag
Item code
Price
Check digit
Program code: 1105000000073F1F2F3
• Short version barcode
F1 F2 I1
Flag Item code
I2
P1
P2
P3 C/D
Price (x 10) Check digit
Program code: 0013000000042F1F20
98
Scanning PLU maintenance programming
Batch maintenance PLU programming
Programming procedure
A
Proceeds the next
vacant record.
~
63s 6 0070s 6 : : 6a 6
PGM
Mode switch
Record No. (001 ~ 999)
*1
Add/
Modify
OBR
Code
B
PRICE
~
6
:
6 a6B 6
Scanning
6
6
: : 6a6
SHIFT
{
}
NLU
B
Unit price/quantity
Action code
B
Delete
*1
og
P
Link-#
a
~
~
6
6
6
:
:
6 a 6 : : 6a 6
{
}
DEPT
B
Status
Character
*1
*1
*1
B
A
~
6
: : 6a 6
:
~
:
6a 6 : : 6 a 6 s
Bottle link
Mix & match
Optimum stock
*1
*1
*1
*1 Skip by general function programming address code 33.
Activation of batch maintenance PLU
Activation procedure
Activation
6 3s 6 4070s 6
a
s
PGM
Mode switch
Cancellation
TE-2200/2400 Dealer's Manual
99
Key function/machine feature (P3)
Scanning PLU direct maintenance programming
A
Programming procedure
63s 6 0071s 6
PGM
Mode switch
OBR
B
Scanning
Code
PRICE
6
:
6 a6B 6
6
6
: ~ : 6a6
SHIFT
}
{
NLU
B
Unit price/quantity
Action code
*1
Link-#
a
6
6
6
:
:
6 a 6 : ~ : 6a 6
~
}
{
B
DEPT
Status
Character
*1
*1
*1
A
6
: ~ : 6a 6 : ~ : 6 a 6 : : 6 a 6 s
Bottle link
Mix & match
Optimum stock
*1
*1
*1
*1 Skip by general function pro-
gramming address code 32.
100
Scanning PLU individual programming
Programming procedure
(Batch maintenance)
(PLU direct)
0170
63s6 0171 s6
PGM
Mode switch
B
OBR
B
Scanning
Code
PRICE
6
: : 666 s6 B6
6
6
SHIFT
}
{
NLU
B
Address code
B
Address code 22:
character programming
~
6
6
:
:
6 a6 s
Character
B
a
Link-#
Address code 11:
link programming
og
6
6 s
DEPT
B
}
{
P
B
Address code 13,20,21,23: 6 : :
6 a6 s
~
other programming
Program data
TE-2200/2400 Dealer's Manual
101
Key function/machine feature (P3)
Program data
Action code
Description
Choice
Program code
Action code:
Addition = 0
Significant
number
:
Modification = 1
D1
Deletion = 2 (Not effective for direct PLU maintenance)
Unit price/quantity (Address code 21 for individual feature programming)
Description
Choice
Program code
Integer part
(0000 ~ 9999)
: : : :
D12 D11 D10 D9
Unit quantity (0.01 ~ 9999.99)
Unit price (000000 ~ 999999)
Decimal part
(00 ~ 99)
: :
D8 D7
Significant
numbers
: : : : : :
D6 D5 D4 D3 D2 D1
Link-# (Address code 11 for individual feature programming)
Description
Choice
Program code
Significant
numbers
: :
Link group record No. (00 ~ 99)
D4 D3
Significant
numbers
: :
Link department record No. (00 ~ 99)
D2 D1
Bottle link (Address code 13 for individual feature programming)
Description
Choice
Program code
Significant
numbers
: : : :
Bottle link record No. (0000 ~ 9999)
D4 D3 D2 D1
Optimum stock (Address code 14 for individual feature programming)
Description
Choice
Program code
Significant
numbers
Optimum stock quantity (0.001 ~ 99.999)
Enter without decimal point.
: : : : :
D5 D4 D3 D2 D1
Mix & match (Address code 20 for individual feature programming)
Description
Choice
Program code
Significant
numbers
: :
Link mix & match record No. (00 ~ 99)
D2 D1
102
Status (Address code 23 for individual feature programming)
Description
Choice
Program code
Significant
numbers
Taxable status:
: :
See below. (In case of “00”, follow the linked department taxable status.)
D6 D5
;
Always “0”
Always “0”
D4
;
D3
No = 0
Yes = 1
Enable 0 unit price.
(Use this bit to change the status with that of the linked department.)
a
:
No = 0
Yes = 2
Enable negative price.
b
(a+b+c)
D2
(Use this bit to change the status with that of the linked department.)
No = 0
Yes = 4
Hash
c
(Use this bit to change the status with that of the linked department.)
No = 0
Yes = 1
Permit price change operation
a
(Use this bit to change the status with that of the linked department.)
:
No = 0
Yes = 2
Permit multiplication operation
b
(a+b+c)
D1
(Use this bit to change the status with that of the linked department.)
No = 0
Yes = 4
Price input compulsory
c
(Use this bit to change the status with that of the linked department.)
og
Taxable status
P
for the U.S./Singapore
No = 0
Yes = 1
:
Food stamp (for Singapore, always “0”)
D6
No = 0
Yes = 1
Taxable 1 status
Taxable 2 status
Taxable 3 status
a
b
c
:
No = 0
Yes = 2
(a+b+c)
D5
No = 0
Yes = 4
for Canada
No = 0
Yes = 1
:
Donuts status
D6
Non tax = 0
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
Taxable 1 & 3 = 6
Taxable 1 & 4 = 7
Significant
number
:
Taxable 4 = 4
D5
Taxable 1 & 2 = 5
for Other area
Non tax = 0
Taxable 4 = 4
Taxable 5 = 5
Taxable 6 = 6
Taxable 7 = 7
Taxable 8 = 8
Taxable 9 = 9
Taxable 10 = 10
Significant
numbers
Taxable 1 = 1
Taxable 2 = 2
Taxable 3 = 3
: :
D6 D5
One touch NLU programming
Programming procedure
To the next record
OBR
Code
B
NLU
63s6 : ~ : 77s6
6 B6 s
PGM
Mode switch
{
}
Scanning
Rec No. (up to 3 digits)
TE-2200/2400 Dealer's Manual
103
Key function/machine feature (P3)
Issuing program reading report of program 3 mode
Issuing procedure
63s6 s
PGM
Mode switch
Report sample
— Program read symbol
03....................
P
— Batch X/Z program
BATCH01
00
0001-29
11-12-17-15-00
00-00-00-00-00
0002-29
CHECK
CREDIT2
PD
0001-02
00000000000000
0002-02
— Transaction key program
— Key character/rec-#/file-#
— Key program
BATCH02
01
11-12-17-15-00
00-00-00-00-00
00000000000000
0003-02
00000000000000
— Clerk detail link program
0001-30
GROSS
0002-30
NET
Department program
— Key character/rec-#/file-#
— Key program
0001-01
0002-01
DEPT01
0001-05
00000000000000
000000
— Batch program 1166
— Batch program 1566
— Batch program 1666
— Batch program 1766
11-66
15-66
16-66
17-66
DEPT02
Arrangement program
— Rec-#/file-#/arrange no.
— Key descriptor/rec-#/file-#
@1.23
0001-38
REG1
1
000001
204-000
001-000
002-000
026-051
013-001
000000
00
0002-05
2
Clerk program
DEPT01
CASH
0002-38
— Clerk name/rec-#/file-#
— Clerk #/drw-#/secret-#
— Compulsory
C01
0001-07
000001000001
0000000000
00000000
67
— Commission rate
— Check # range
68
69
70
— Employee program
— Scheduler program
CSHR01
0001-061
0000000000
0002-061
000000000000
0000000000
0002-07
— Operation restriction
CSHR02
C02
0001-62
000000
00000000000000
0000000000
000000
— Time range program
— General control program
— Tax table
0001-09 00:00 -> 01:00
0002-09 01:00 -> 02:00
0003-09 02:00 -> 03:00
0002-62
MC#01
000000000000
0001-22
0002-22
0003-22
2200000000
0000000000
0000000000
0001-91
1001
— Terminal connection table
— Printer connection table
0001-93
0002-93
000000
100000
0001-25
TX1
10.25%
0000
TX1
— I/O parameter table
0001-98 00000000000000
0002-98 00000000000000
TX1
5003
104
Character (Program 2)
To other address code
To the next address code
Programming descriptors
Programming procedure
File No.
Rec No.
Character
~
62s6 : : : : s6
6 a6 s
PGM
Mode switch
✔ See “Entering characters” section.
Address code
Programming data
Fixed totalizer (up to 12 characters)
Address
Contents
code
Address
code
Initial character
Contents
Initial character
0101
0201
0301
0401
0501
0601
0701
0801
0901
1001
1101
1201
1301
1401
1501
1601
1701
1801
1901
2001
2101
2201
2301
2401
2501
2601
2701
2801
2901
3001
3101
3201
3301
3401
3501
3601
3701
3801
3901
4001
4101
4201
4301
4401
4501
4601
4701
4801
4901
5001
5101
Gross sales total
Net sales total
Cash in drawer
5201
5301
5401
5501
5601
5701
5801
5901
6001
6101
6201
6301
6401
6501
6601
6701
6801
6901
7001
7101
7201
7301
7401
7501
7601
7701
7801
7901
8001
8101
8201
8301
8401
8501
8601
8701
8801
8901
9001
9101
9201
9301
9401
9501
9601
9701
9801
9901
Clerk commission 2 total
Foreign currency cash in drawer 1
Foreign currency check in drawer 1
Foreign currency cash in drawer 2
Foreign currency check in drawer 2
Foreign currency cash in drawer 3
Foreign currency check in drawer 3
Foreign currency cash in drawer 4
Foreign currency check in drawer 4
Reduction
Coupon
Item return
Clear counter
Rounding 2 *
Rounding 1
Cancellation
Money declaration
Taxable amount
Tax 1
Tax exempt 1
Taxable amount 2
Tax 2
Tax exempt 2
Taxable amount 3
Tax 3
Tax exempt 3
Taxable amount 4
Tax 4
Tax exempt 4
Taxable amount 5
Tax 5
Tax exempt 5
Taxable amount 6
Tax 6
Tax exempt 6
Taxable amount 7
Tax 7
Tax exempt 7
Taxable amount 8
Tax 8
Tax exempt 8
Taxable amount 9
Tax 9
GROSS
NET
CAID
CATL
CA-
CA+
CHID
CHTL
CH-
CH+
CKID
CKTL
CK-
CK+
CRID(1)
CRID(2)
CRID(3)
CRID(4)
CRTL
C-2
CECA1
CECK1
CECA2
CECK2
CECA3
CECK3
CECA4
CECK4
DC
Cash declared amount
Declared short cash amount
Declared over cash amount
Charge in drawer
Charge declared amount
Declared short charge amount
Declared over charge amount
Check in drawer
Check declared amount
Declared short check amount
Declared over check amount
Credit 1 in drawer
COUPON
REF
P
CLEAR
ROUND
ROUND
CANCEL
DECLA
TA1
TX1
EX1
TA2
TX2
EX2
TA3
TX3
EX3
TA4
TX4
EX4
TA5
TX5
EX5
TA6
TX6
EX6
TA7
TX7
EX7
TA8
TX8
EX8
TA9
TX9
EX9
TA10
TX10
EX10
NON TAX
Credit 2 in drawer
Credit 3 in drawer
Credit 4 in drawer
Credit declared amount
Declared short credit amount
Declared over credit amount
Cash in drawer *
Cash declared amount *
Declared short cash amount *
Declared over cash amount *
Charge in drawer *
Charge declared amount *
Declared short charge amount *
Declared over charge amount *
Check in drawer *
Check declared amount *
Declared short check amount *
Declared over check amount *
Credit 1 in drawer *
Credit 2 in drawer *
Credit 3 in drawer *
Credit 4 in drawer *
Credit declared amount *
Declared short credit amount *
Declared over credit amount *
Food stamp in drawer
Food stamp cash change
EBT in drawer
CR-
CR+
CAID2
CATL2
CA- 2
CA+ 2
CHID2
CHTL2
CH- 2
CH+ 2
CKID2
CKTL2
CK- 2
CK+ 2
CRID2(1)
CRID2(2)
CRID2(3)
CRID2(4)
CRTL2
CR- 2
CR+ 2
FSID
FSCACG
EBTTL
EBTCACG
RF
CUST
AVRG
FEE
+
NB
C-1
EBT cash change
Refund mode total
Customer count
Average sales per customer
Check cashing service fee
New balance fee
(not used)
Clerk commission 1 total
Tax exempt 9
Taxable amount 10
Tax 10
Tax exempt 10
Nontaxable amount
* Totalizers for sub currency
TE-2200/2400 Dealer's Manual
105
Character programming (P2)
Group character
Up to 12 characters
Address
Contents
Initial character
code
0106
0206
0306
:
Group 01
Group 02
Group 03
:
GROUP01
GROUP02
GROUP03
:
9906
Group 99
GROUP99
Clerk character
Up to 12 characters
Address
code
Initial character
TE-2200/2400 (Eu) TE-2200/2400 (US)
Contents
C
C
C
01
02
03
C01
C02
C03
:
0107
0207
0307
:
Clerk 01
Clerk 02
Clerk 03
:
:
C
99
C99
9907
Clerk 99
Table analysis character
Up to 12 characters
Address
code
Contents
Initial character
0118
0218
0318
:
Table 01
Table 02
Table 03
:
TBL01
TBL02
TBL03
:
9918
Table 99
TBL99
Grand total character
Up to 12 characters
Address
code
Contents
Initial character
0120
0220
0320
Grand total 01
GT1
GT2
GT3
Grand total 02
Grand total 03
106
Special character
Address
code
Contents
Initial character
$@ No/ **
• @No/ ** ⁄
NoCT @LB *QT
NoCT@ LB *QT
BUSY
U.S.
main currency symbol (2), @ (2), No. (2), split pricing (2), not used (1)
training filler (1), training symbol (1), not used (1), sub currency symbol (2)
0123
0223
0323
Others
U.S.
No. of item sold (2), No. of customer (2), scalable item @ (2),
scale weight (2), new price (2), multiplication display (2)
Others
U.S.
multiplication (6) check in use (6)
X
BUSY
Others
0423
0523
0623
0723
0823
0923
1023
1123
1223
1323
1423
1523
1623
1723
1823
1923
2023
2123
2223
2323
2423
2523
2623
2723
2823
2923
3023
3123
3223
3323
3423
3523
3623
3723
3823
3923
4023
4123
4223
4323
4423
4523
4623
4723
4823
4923
taxable symbol 1 (3 each) for tax 1, tax 2, tax 3, tax 4, tax 5
taxable symbol 2 (3 each) for tax 6, tax 7, tax 8, tax 9, tax 10
taxable symbol 3 (3 each) for tax 1/2, tax 1/3, tax 1/4, not used, tax 2/3
taxable symbol 4 (3 each) for not used, not used, not used, nontax, all, F/S
foreign currency (2 each), character edit mode (INS/OVR) (4 each)
mode symbol 1 (4 each) REG1/2, RF, REG–
mode symbol 2 (4 each) PGM, Daily X, Daily Z, Periodic
mode symbol 3 (4 each) training, not used, PGM read
decimal: amount/q’ty, separator (main/sub) (1 each), not used (3), square (7)
A.M., P.M. (3 each), ST displayed on the dot display (2)
slip continued (12), page (2)
T1 T2 T3 T4 T5
T6 T7 T8 T9 T10
T12T13T14 T23
F
* * * *
*
REG
Pn
RFR-
X Z XZ
PGMX
TRG
..,.., X
AM PM ST
CONTINUED
P
(not used)
display subtotal symbol (ST key) (16)
subtotal symbol (16)
ST
ST
total symbol (16)
TL
change symbol (16)
CG
check cashing fee (16)
-
P
check cashing amount (16)
CACG
Bon message (12)
** STUB **
break (16)
**BREAK END**
CHECK No.
check No. (10)
service total (16)
SRVC TL
item discount total (16)
DISCOUNT
scale manual entry (12)
MANUAL ENTRY
(not used)
report total symbol (12)
TL
report old price symbol (16)
OLD PRC
RED PRC
FSCG
red price symbol (16)
food stamp change symbol (16)
table No. symbol (10)
TABLE No.
future order message (16)
**Future Order**
DECLA
declared amount (16)
entering child item in separate check or void item in previous item void operation
current stock (16)
Sub item ?
STK(NEW)
STK(OLD)
STK(ADD)
** REVIEW **
* END **
EURO money
RECORD
last stock (16)
added stock (16)
reviewing (16)
end of transaction (16)
designating sub currency (16)
Element title 1 of CF X/Z report (16)
Element title 2 of CF X/Z report (16)
Element title 3 of CF X/Z report (16)
Element title 4 of CF X/Z report (16)
Element title 5 of CF X/Z report (16)
Element title 6 of CF X/Z report (16)
Element title 7 of CF X/Z report (16)
DESCRIPTOR
QUANTITY/No
QUANTITY
No
AMOUNT
DISCOUNT
TE-2200/2400 Dealer's Manual
107
Character programming (P2)
Address
Contents
code
Initial character
5023
5123
5223
5323
5423
5523
5623
5723
5823
5923
6023
6123
6223
6323
6423
6523
6623
6723
6823
6923
7023
7123
7223
7323
7423
7523
7623
7723
7823
7923
8023
8123
8223
element title 8 of CF X/Z report (16)
element title 9 of CF X/Z report (16)
element title 10 of CF X/Z report (16)
element title 11 of CF X/Z report (16)
element title 12 of CF X/Z report (16)
element title 13 of CF X/Z report (16)
element title 14 of CF X/Z report (16)
element title 15 of CF X/Z report (16)
element title 16 of CF X/Z report (16)
element title 17 of CF X/Z report (16)
element title 18 of CF X/Z report (16)
element title 19 of CF X/Z report (16)
element title 20 of CF X/Z report (16)
element title 21 of CF X/Z report (16)
element title 22 of CF X/Z report (16)
element title 23 of CF X/Z report (16)
element title 24 of CF X/Z report (16)
element title 25 of CF X/Z report (16)
element title 26 of CF X/Z report (16)
element title 27 of CF X/Z report (16)
element title 28 of CF X/Z report (16)
element title 29 of CF X/Z report (16)
element title 30 of CF X/Z report (16)
model name 1 of CF X/Z report (16)
model name 2 of CF X/Z report (16)
header title 1 of CF X/Z report (16)
header title 2 of CF X/Z report (16)
header title 3 of CF X/Z report (16)
header title 4 of CF X/Z report (16)
header title 5 of CF X/Z report (16)
header title 6 of CF X/Z report (16)
header title 7 of CF X/Z report (16)
header title 8 of CF X/Z report (16)
OLD AMOUNT
RED AMOUNT
STOCK
CUSTOMER
GROSS AMOUNT
NET No
NET AMOUNT
GROSS QUANTITY
No of DISCOUNT
DISCOUNT AMOUNT
RANDOM CODE
OBR CODE
CLOCK IN DATE
CLOCK IN TIME
CLOCK OUT DATE
CLOCK OUT TIME
WORKING TIME
EMPLOYEE NAME
EMPLOYEE No
CLERK
START TIME
END TIME
PRICE SHIFT
TE-2200
TE-2400
MODEL
MACHINE
REPORT
FILE
MODE
Z COUNTER
DATE
TIME
108
Message
Up to 24 characters
Address
code
Contents
Initial character
Yours
YOUR RECEIPT
THANK YOU
CALL AGAIN
0132
0232
0332
0432
0532
0632
0732
0832
0932
1032
1132
1232
1332
1432
1532
1632
1732
1832
1932
2032
2132
2232
2332
2432
2532
2632
2732
2832
2932
3032
3132
3232
3332
3432
3532
3632
3732
3832
3932
4032
4132
4232
1st line of logo message
2nd line of logo message
3rd line of logo message
4th line of logo message
1st line of commercial message
2nd line of commercial message
3rd line of commercial message
4th line of commercial message
1st line of bottom message
2nd line of bottom message
3rd line of bottom message
4th line of bottom message
1st line of bill top message
2nd line of bill top message
3rd line of bill top message
4th line of bill top message
1st line of bill copy message
2nd line of bill copy message
3rd line of bill copy message
4th line of bill copy message
1st line of bill bottom message
2nd line of bill bottom message
3rd line of bill bottom message
4th line of bill bottom message
Post receipt message
P
DUPLICATE RECEIPT
1st line of guest intermediate message
2nd line of guest intermediate message
3rd line of guest intermediate message
4th line of guest intermediate message
1st line of guest bottom message
2nd line of guest bottom message
3rd line of guest bottom message
4th line of guest bottom message
5th line of guest bottom message
6th line of guest bottom message
7th line of guest bottom message
8th line of guest bottom message
9th line of guest bottom message
10th line of guest bottom message
1st line of Australian GST MOF message
2nd line of Australian GST MOF message
3rd line of Australian GST MOF message
TAX INVOICE
* INDICATES
TAXABLE SUPPLY
TE-2200/2400 Dealer's Manual
109
Character programming (P2)
Report header
Up to 12 characters
Address
Contents
Initial character
code
0124
0224
0324
0424
0524
0624
0724
0824
0924
1024
1124
1224
1324
1424
1524
1624
1724
1824
1924
2024
2124
2224
2324
2424
2524
2624
2724
Fixed totalizer report
FIX
Transaction key report
PLU report
TRANS
PLU
Department report
Group report
DEPT
GROUP
CASHIER
Cashier/clerk report
Not used
Hourly sales report
Monthly sales report
Not used
HOURLY
MONTHLY
SUB DEPT
ANALYSIS
OPEN CHK
SCAN PLU
HOURLY ITEM
PLU STOCK
FLASH
Table analysis report
Open check report
Scanning PLU
Hourly item
PLU stock report
Financial report
Mix & match
MIX&MATCH
PLU AMT
PLU by amount
PLU by quantity
Department by amount
Department by quantity
Scanning PLU best
Inactive scanning PLU
Individual item
PLU QTY
DEPT AMT
DEPT QTY
PLU BEST
NON ACTIVE
INDIVIDUAL
NFP
Not used
Time & attendance
Scanning PLU stock
ATTENDANCE
SCAN STOCK
Batch X/Z header
Up to 12 characters
Address
code
Contents
Initial character
0129
0229
0329
:
Batch 01
Batch 02
Batch 03
:
BATCH 01
BATCH 02
BATCH 03
:
1029
Batch 10
BATCH 10
Check endorsement message
Up to 40 characters
Address
Contents
Initial character
code
0133
0233
0333
0433
Check endorsement message 01
Check endorsement message 02
Check endorsement message 03
Check endorsement message 04
110
Slip/external printer message
Up to 40 characters (Contents are the same as file032.)
Address
Contents
code
Initial character
0134
0234
0334
:
Slip/external printer message 01
Slip/external printer message 02
Slip/external printer message 03
:
YOUR RECEIPT
THANK YOU
CALL AGAIN
:
4134
Slip/external printer message 41
* INDICATES TAXABLE SUPPLY
Recall character message
Up to 40 characters
Address
code
Contents
Initial character
0139
0239
0339
:
Recall character 01
Recall character 02
Recall character 03
:
99939
Recall character 999
Mix & match character
Up to 12 characters
Address
code
P
Contents
Initial character
0151
0251
0351
:
Mix & match 01
Mix & match 02
DISCOUNT01
DISCOUNT02
DISCOUNT03
:
Mix & match 03
:
9951
Mix & match 99
DISCOUNT99
Employee character
Up to 12 characters
Address
code
Contents
Initial character
0161
0261
0361
:
Employee 01
CSHR01
CSHR02
CSHR03
:
Employee 02
Employee 03
:
9961
Employee 99
CSHR99
Help message
Up to 24 characters
Address
code
Contents
Initial character
00185
00285
00385
:
Help message 001
Help message 002
Help message 003
:
ENTER NUMBER THEN
PRESS <HELP> KEY.
:
19985
Help message 199
TE-2200/2400 Dealer's Manual
111
Character programming (P2)
Terminal connection table
Up to 8 characters
Address
Contents
Initial character
code
0191
Physical No. 01
MC#01
AT command
Up to 62 characters
Address
code
Contents
Initial character
AT COMMAND****
ATA
***
0196
0296
Command set to MODEM
on hook, confirmation
ATI4
Error message
Up to 16 characters
Address
code
Contents
Error code
Initial character
0180
0280
0380
:
E001
Mode switch position changed before… Wrong mode
Error code
E002
:
:
23880
Flash memory format is illegal.
Illegal format
Miscellaneous message
Up to 16 characters
Address
code
Contents
Initial character
0178
0278
0378
:
Register total working time
Register start date message
RAM message in PGM5
:
GT TIME
START DATE
RAM
:
5878
Model name
Printing guidance message
Up to 24 characters
Address
Contents
Initial character
code
0179
0279
0379
:
not used
not used
not used
:
:
8579
Euro currency system setup
set.
112
X/Z guidance message
Up to 16 characters
Address
code
Contents
Initial character
0182
0282
0382
:
PLU range report message 1st line
Input start No. message 1st line
Input start No. message 2nd line
:
PLU by range
Input start No.
and press <#1>
:
4882
PLU reset message 1st line
PLU Z clear
Program guidance message
Up to 16 characters
Address
Contents
Initial character
code
0183
0283
0383
:
Range program message 1st line
Input start No. message 1st line
Input start No. message 2nd line
:
Range PGM
Input start No.
and press <#1>
:
9783
P
Registration guidance message
Up to 16 characters
Address
Contents
code
Initial character
0181
0281
0381
:
Guidance message of NFP 1st line
Guidance message of NFP 2nd line
Guidance message of NFP 3rd line
:
Not Found PLU
Input Unit Price
,and press DEPT
:
2281
Guidance message of price comp 4th line > key
Online password
Up to 8 characters
Address
code
Contents
Initial character
0197
Online password
TE-2200/2400 Dealer's Manual
113
Character programming (P2)
Programming item/key descriptors
Programming procedure
Department key/transaction key
To another department/transaction key
Department key
Transaction key
Characters
62s6
6
6 s
PGM
Mode switch
✔ See “Entering
characters” section.
PLU
To a new (not sequential) PLU
To the next PLU
6 2s6 PLU No. +6 a6 s
Characters
PGM
Mode switch
(Rec No,: 4 digits)
✔ See “Entering characters” section.
(Random code: 6 digits)
Flat-PLU key
To another flat-PLU key
MENU
Characters
Flat-PLU key
62s6
6 B6
6s
SHIFT
PGM
Mode switch
✔ See “Entering characters” section.
Programming data
Department
up to 16 characters
Contents
Initial character
DEPT01
DEPT02
DEPT03
:
Department 01
Department 02
Department 03
:
Department 99
DEPT99
PLU/flat-PLU
up to 16 characters
PLU No.
Contents
Initial character
PLU0001
PLU0002
PLU0003
:
0001
0002
0003
:
PLU 0001
PLU 0002
PLU 0003
:
Maximum No.: Depend on the model
114
Transaction key
Up to 12 characters
Function
Add check
Arrangement
Birth date
Bill copy
Bottle return
Cancel
Code
094 ADD CHK
044 ARG
Initial character
Function
Normal receipt
OBR
Old check
One touch NLU
Open
Code
016 NRMRCT
103 OBR
092 OLD CHK
138 NLU
067 OPEN
068 OPEN2
117 OPEN CHK
073 OPE X/Z
021 PD
022 P.UP
029 +
048 PLU#
026 PB
079 PBST
030 %+
049 PRC
104 PRC CHG
008 PRCINQ
069 PRICE SHIFT
083 QT
031 TAX
131 RECALL
038 RCT
076 RCT ON/OFF
020 RC
060 RED
Initial character
047 BILL
053 BR
236 CANCEL
001 CASH
002 CHARGE
039 CK.E
012 CHKP
003 CHECK
072 CLK#
Open2
Cash amount tendered
Charge
Open check
Operator read/reset
Paid out
Pick up
Plus
Check endorsement
Check print
Check tender
Clerk number
Clock-in/out
Coupon
Coupon 2
Credit
Cube
Currency exchange
Customer number
Date/Time
Decimal point
Declaration
Department
Deposit
Discount
Eat-in
EBT tender
Enter
Error correct
Flat PLU *
Food stamp status shift
Food stamp subtotal
Food stamp tender
Help
Ketten Bon
Loan
Lock out unused key
Manual tax
Media change
Menu shift
Merchandise subtotal
Minus
PLU
108 CLOCK-IN/OUT Previous balance
023 COUPON
036 CPN2
004 CREDIT
090 XXX
045 CE
043 CT
101 DATE/TIME
098 .
061 DECLA
nn051 DEPTnn
025 DEPOSIT
028 %–
128 EAT-IN
007 EBTTD
105 ENT
034 CORR
nnnn063 PLUnnnn
059 F/S
Previous balance subtotal
Premium
Price
Price change
Price inquiry
Price shift
Quantity/for
Rate tax
Recall
Receipt
Receipt on/off
Received on account
Red price
Refund
Review
Separate check
Slip back feed/release
Slip feed/release
Slip print
Square
Stock inquiry
Store
Subtotal
Table number
Takeout
Tax exempt
Tax status shift
Taxable amount subtotal
Text print
P
033 RF
071 REVIEW
095 SEP CHK
054 SB/R
056 SF/R
055 SLIP
084 XX
009 STKINQ
130 STORE
075 SUBTOTAL
058 TBL#
129 TAKE-OUT
062 EXEMPT
057 T/S
081 FSST
005 FSTD
141 HELP
113 X/KETTEN
019 LOAN
000
032 TAX
118 MEDIA CHG
064 MENU
080 MDST
027 -
077 TAST
011 PRT
Multiplication/Date/Time
Multiplication
New balance
New check
New/old check
No sale
082 X
100 X
006 NB
091 NEW CHK
093 NEW/OLD
042 NS
Text recall
Three zero
Tip
Tray total
Two zero
010 CHAR
097 000
015 TIP
074 TRAY TL
096 00
037 VLD
Validation
VAT
Non-add
040 #
046 VAT
Non-add/No sale
041 #/NS
Void
035 VOID
TE-2200/2400 Dealer's Manual
115
Character programming (P2)
Programming item/clerk descriptors by range
Programming procedure
PGM
Mode switch
6
2s
6
990000: : s
6
Department = 05
PLU/flat-PLU = 04
}
Ends “the last record”.
Starts “0001”.
s
6
:
:
6
a
6
: :
6
a
6
:
~
: a
6
~
~
Start rec-#
(Max. 4 digits)
End rec-#
(Max. 4 digits)
Program data
(character)
Program data
Department
up to 16 characters
Contents
Initial character
Department 01
DEPT01
DEPT02
DEPT03
:
Department 02
Department 03
:
:
Department 99
DEPT99
PLU/flat-PLU
up to 16 characters
PLU No.
0001
0002
0003
:
Contents
Initial character
PLU0001
PLU0002
PLU0003
:
PLU 0001
PLU 0002
PLU 0003
:
Maximum No.: Depend on the model.
116
Entering characters
By character keyboard
TE-2200 character keyboard
Example:
Input “
A
p
p
l
e
J
u
i
c
e
”,
enter “DBL”“A” “SHIFT”“p” “p” “l” “e” “SPACE” “CAP”“J” “SHIFT”“u” “i” “c” “e” -.
RECEIPT
FEED
JOURNAL
FEED
C
7
1 C
INS/
OVR
A
B
b
C
c
D
d
E
e
F
f
G
g
SHIFT
a
8
2 3
H
h
I 7
J 8
j
K 9
k
L
l
M
m
N
n
<—
—>
7
4
1
0
8
5
2
9
6
3
i
5
A
O
o
P 4
p
Q 5
q
R 6
r
S
s
#-2
#-1
B
T
t
U 1
u
V 2
v
W 3
w
X
x
4
DOUBLE
SIZE
9 0
00
Y
y
Z 0
z
•
P
TE-2200 Eu
RECEIPT
FEED
JOURNAL
FEED
C
7
1 C
INS/
OVR
A
a
B
b
C
c
D
d
E
e
F
f
G
g
SHIFT
8
2 3
H
h
I 7
i
J 8
j
K 9
k
L
l
M
m
N
n
<—
—>
7
4
1
0
8
5
2
9
6
3
5
A
O
o
P 4
p
Q 5
q
R 6
r
S
s
#-2
#-1
B
T
t
U 1
u
V 2
v
W 3
w
X
x
4
DOUBLE
SIZE
9 0
00
Y
y
Z 0
z
•
TE-2200 US
TE-2200/2400 Dealer's Manual
117
Character programming (P2)
TE-2400 character keyboard
Example:
Input “
A
p
p
l
e
J
u
i
c
e
”,
enter “DBL”“A” “SHIFT”“p” “p” “l” “e” “SPACE” “CAP”“J” “SHIFT”“u” “i” “c” “e” -.
RECEIPT JOURNAL
MENU
FEED
FEED
007
014
021
028
027
035
034
042
041
049
048
056
055
063
062
070
069
068
7;
-
2
/
.
,
•
'
:
+
?
006
013
020
2 3
C
1
3
4
R
F
V
5
6
7
8
I
9
O
L
0
!
@
#
$
%
^
&
(
)
*
005
012
019
026
025
024
033
040
047
054
061
8
Q
A
Z
W
S
X
E
D
C
T
G
B
Y
H
N
U
J
P
q
w
e
r
f
t
y
u
i
o
p
067
7
4
1
8
5
2
9
6
3
004
011
018
032
039
046
053
060
K
a
s
d
g
h
j
k
l
003
010
017
031
038
045
052
051
050
059
066
A
#-2
B
M
z
x
c
v
b
n
m
002
009
016
015
023
030
029
037
036
044
058
065
099
6 1 5
CAP
C 4
0 9000•
OVR
SHIFT
008
DBL
064
#-1
/INS
TE-2400 Eu
001
022
043
057
RECEIPT JOURNAL
MENU
FEED
FEED
007
014
021
028
035
042
049
056
063
062
070
069
7;
-
/
.
,
•
'
:
+
?
006
013
020
027
034
041
048
055
2 3
1
Q
A
Z
2
W
S
3
4
R
F
V
5
6
7
8
9
O
L
0
!
@
#
$
%
^
&
(
)
C
7
4
*
005
012
019
026
025
024
033
040
047
054
061
068
8
p
E
D
C
T
G
B
Y
H
N
U
J
I
P
q
w
e
r
f
t
y
u
i
o
8
5
2
9
6
3
004
011
018
032
039
046
053
060
067
K
a
s
d
g
h
j
k
l
059
003
010
017
031
038
045
052
051
050
066
065
A
#-2
B
X
M
z
x
c
v
b
n
m
1
002
009
016
023
030
037
044
058
099
0 9000•
6 1 5
SHIFT
C 4
OVR
CAP
DBL
#-1
/INS
TE-2400 US
001
008
015
022
029
036
043
057
064
1Shift key
7Alphabet keys
TE-2200:
Use those keys to enter characters.
Pressing this key shifts the character through the upper-
case letter, lower case letter and numerics.
TE-2400:
Pressing this key shifts the character from the uppercase
letter to lower case letter and vice versa.
8Numeric keys
Use those keys to enter program codes, memory number
and character codes.
9Character fixed key
Press this key to fix all entered characters before you assign
them to function keys, PLUs, department keys and so on.
2Left cursor key
Move the cursor to the left one by one to modify characters.
0Backspace/Character code fixed key
Registers one character with code (2 or 3 digit).
Clears the last entered character, much like a back space
key.
3Right cursor key
Move the cursor to the right one by one to modify charac-
ters.
4Double size letter key
AProgram end key
Specifies that the next character you enter a double size
character.
You must press this key before each double size character.
Terminates the character programming.
BCharacter enter key
Registers the programmed characters.
5Space key
CInsert/Override key
Set a space by depression.
Press this key to change the status “Insert” between the
original characters or “Override” the original characters.
6CAP key
Pressing this key shifts the character to the uppercase letter.
118
By character code
Every time you enter a character, choose character codes by the character code list (below) and press the ^
key to settle it. After you complete entering characters, press the -key to fix them.
Example:
Input “
A
p
p
l
e
J
u
i
c
e
”,
”
enter “ 255^65^112^112^108^101^32^74^117^105^99^101^-
Character code list
Chara Code Chara Code Chara Code Chara Code Chara Code Chara Code Chara Code
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Space
!
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
97
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
98
"
99
#
100
101
102
103
104
105
106
107
108
109
110
111
$
%
&
'
(
)
P
*
+
,
-
.
/
Chara Code Chara Code Chara Code Chara Code Chara Code Chara Code Chara Code
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
‹
ƒ
á
í
ó
ú
ñ
Ñ
ª
º
¿
®
Ó
ß
Ô
Ò
õ
Õ
µ
p
P
Ú
Û
Ù
y
Y
-
D
Ê
Ë
È
⁄
Í
Î
Ï
_
3
/
¶
§
÷
4
Á
Â
À
©
ã
Ã
_
¨
¬
•
1
1
/
2
1
3
2
/
4
¡
«
»
¢
¥
ı
|
Ì
Double
sized
¤
TE-2200/2400 Dealer's Manual
119
Character programming (P2)
Editing characters
Correcting a character just entered
OPERATION
DISPLAY (character)
“L” “E” “N” “O” “N”
1 Enter LENON, instead of LEMON.
LENON
LENON
LENON
LEMON
yyy
1 Press left arrow key three times.
1 Override mode
INS/
B
OVR
“M”
1 Enter “M”.
Correcting and adding a PLU descriptor already set
OPERATION
DISPLAY (character)
-
1 Enter “00”.
15+
1 Enter PLU No.
1 Enter “Soda” and “space”.
1 Override mode
1 Enter “L”.
lemon
“S”, “o”,“d”, “a”, “ ”
Soda lemon
Soda lemon
Soda Lemon
INS/
B
OVR
“L”
Correcting a key descriptor already set
OPERATION
DISPLAY (character)
-
!
1 Enter “00”.
LENON
LENON
LEMNON
LEMON
1 Designate an appropriate key
1 Press right arrow key two times.
1 Enter “M”.
uu
“M”
^
1 Delete “N”.
Correcting a message descriptor already set
OPERATION
DISPLAY (character)
0101s
1 Enter record and file number.
GRASS
GRASS
GROASS
uu
“O”
1 Press right arrow key two times.
1 Enter “O”.
^
1 Delete “A”.
GROSS
* Reverse or blinking digit indicates cursor position.
120
Issuing program reading report of program 2 mode
Issuing procedure
62s6 s
PGM
Mode switch
Report sample
— Program read symbol
— Fixed totalizer character
— Transaction key character
— Department character
— Group character
P
02....................
0001-32
YOUR RECEIPT
0002-32
THANK YOU
GROSS
NET
0001-01
0002-01
0003-01
0004-01
0005-01
0001-02
0002-02
0003-02
0004-02
0001-05
0002-05
0003-05
0004-05
0001-06
0002-06
0003-06
0004-06
0001-07
0002-07
0003-07
0004-07
0001-18
0002-18
0003-18
0004-18
0001-20
0002-20
0003-20
— Receipt message
CAID
CATL
0001-33
— Check endorsement message
***ENDORSE MESSAGE******
****************
0002-33
CHECK
CHARGE2
PD
AGE***********
0001-34
DEPT01
DEPT02
DEPT03
— Slip/external printer message
***SLIP MESSAGE*********
****************
0002-34
P
E**************
0001-39
GROUP01
GROUP02
GROUP03
— Recall character
CHARACTER RECALL *******
*****************
0002-39
C
01
02
03
L ************
— Clerk character
C
C
ORDER01
ORDER02
ORDER03
0001-65
0002-65
0003-65
0004-65
0001-91
— Order character
TBL01
TBL02
TBL03
— Table character
— Terminal connection table character
MC#01
0001-96
GT1
GT2
GT3
AT COMMAND**************
************************
*******
— AT command
• @No/ ** ™
NoCT@ LB *QT
0001-23
0002-23
0003-23
0002-96
— Special character
ATA
ATI4
X
BUSY
FIX
0001-24
0002-24
0003-24
0004-24
0001-29
0002-29
0003-29
0004-29
— Online password
0001-97
PASSWORD
— Report header character
— Batch X/Z character
TRANS
PLU
BATCH 01
BATCH 02
BATCH 03
TE-2200/2400 Dealer's Manual
121
Character programming (P2)
122
Unit price/rate (Program 1)
Date/time setting
Date setting
*
DATE/
B
TIME
61s6 :: :: ::6
6 C
or
PGM
Mode switch
x
Year
Month
Day
Range: 2000 ~ 2099
*
DATE/
B
TIME
6 1s620: : : : : : 6
6 C
or
PGM
Mode switch
x
Year
Month
Day
Range: 2000 ~ 2099
*
You can use <X>, <X/XX> or <X/KETTEN> instead of these keys.
Time setting
*
DATE/
B
TIME
61s6 : : : : 6
6 C
or
PGM
Mode switch
P
x
Hour
Minute
(00 ~ 23) (00 ~ 59)
*
DATE/
B
TIME
6 1s6 : : : : : 6
6C
or
PGM
Mode switch
x
Minute 10 second
Hour
(00 ~ 23) (00 ~ 59) (0 ~ 5)
*
You can use <X>, <X/XX> or <X/KETTEN> instead of these keys.
Unit price program
Programming procedure
Programming the 1st unit price and unit quantity (to department/flat-PLU key)
To another department/flat-PLU key
Department
PGM
Mode switch
MENU
~
6 1s6
6
: :
Program data
(12 digits)
6
6 s
B
SHIFT
Flat-PLU
TE-2200/2400 Dealer's Manual
123
Unit price/rate programming (P1)
Programming the unit price and unit quantity (to PLU)
To a new (not sequential) PLU
Different program to the next PLU
Same program
PGM
Mode switch
~
6 1s6 +6 : : 6 a6 s
PLU No.
Program data
(Rec No.: 4 digits)
(12 digits)
(Random code: 6 digits)
Program data
Description
Choice
Program code
D12 ~ D7 for non scalable item (unit quantity/2nd unit quantity)
Significant
numbers
: : : :
Unit quantity (integer)
D12 D11 D10 D9
Significant
numbers
: :
Unit quantity (decimal)
D8 D7
D12 ~ D7 for scalable item (unit quantity/2nd unit quantity)
Unit quantity (integer)
Significant
numbers
: :
D12 D11
Significant
numbers
: : :
Unit quantity (decimal)
Always “0”
D10 D9 D8
;
D7
::::::
D6 D5 D4 D3 D2 D1
Significant
numbers
Unit price
124
Rate program
<CURRENCY EXCHANGE>
^
61s6 : : : :
: : : : 6 E6 s
PGM
Mode switch
Integer
Decimal
(Max. 4-digits)
(Max. 4-digits)
Example:
Preset rate
$1.00 = ¥110.50 2 1^105
¥100 = $0.9050 2 0^905
<CHECK>, <NEW BALANCE>, <PREMIUM (%+)>, <DISCOUNT (%–)>, <RATE TAX>
Appropriate
^
61s6 : :
: : 6
6 s
key
PGM
Mode switch
Integer
Decimal
(Max. 2-digits) (Max. 2-digits)
Preset rate
Amount program
<CASH>, <CHECK>, <NEW BALANCE>, <PLUS (+)>, <MINUS (–)>, <COUPON>
Appropriate
61s6 : : : : : :
6
6 s
key
PGM
Mode switch
P |