GE 3504502P327 User Manual

Safety Instructions . . . . . . . . . . .2, 3  
Owner’s Manual  
and Installation  
Installation Instructions . . . . . . . .4  
Operating Instructions  
Automatic Humidity Control . . . . . .6  
Control Settings . . . . . . . . . . . . . .5, 6  
Locking the Controls . . . . . . . . . . . .6  
Care and Cleaning . . . . . . . . . .7–10  
Replacing the Light Bulb . . . . . . . . .8  
Reversing the Door . . . . . . . . . . .9, 10  
Troubleshooting Tips . . . . . . .11, 12  
Consumer Support  
Warranty . . . . . . . . . . . . . . . . . . . . .13  
Consumer Support . . . . . . . . . . . . .14  
Write the model and serial  
numbers here:  
Model # ____________________  
Serial # ____________________  
Find these numbers inside the  
wine chiller on the left side.  
Part No. – 3504502P327  
Cat. No. – WR6M460  
HOW TO CONNECT ELECTRICITY  
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.  
For personal safety, this appliance must be properly grounded.  
The power cord of this appliance is equipped  
with a 3-prong (grounding) plug which mates  
with a standard 3-prong (grounding) wall outlet  
to minimize the possibility of electric shock  
hazard from this appliance.  
This provides the best performance and also  
prevents overloading house wiring circuits which  
could cause a fire hazard from overheated wires.  
Never unplug your wine chiller by pulling on  
the power cord. Always grip plug firmly and  
pull straight out from the outlet.  
Have the wall outlet and circuit checked by a  
qualified electrician to make sure the outlet is  
properly grounded.  
Repair or replace immediately all power cords  
that have become frayed or otherwise damaged.  
Do not use a cord that shows cracks or abrasion  
damage along its length or at either end.  
If you have only a standard 2-prong wall outlet,  
it is your personal responsibility and obligation  
to have it replaced with a properly grounded  
3-prong wall outlet.  
When moving the wine chiller away from the  
wall, be careful not to roll over or damage the  
power cord.  
The wine chiller should always be plugged into  
its own individual electrical outlet which has  
a voltage rating that matches the rating plate.  
USE OF ADAPTER PLUGS  
Adapter plugs are not permitted in Canada.  
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.  
SAVE THESE INSTRUCTIONS  
3
Installing the wine chiller.  
Removing the Packaging  
Before using the wine chiller, be sure all packing materials and tape have been removed,  
including the protective film covering the control and any film protecting the cabinet.  
If you are discarding an old refrigeration product, remove the doors to reduce the danger  
of children being trapped inside.  
Installation Guidelines  
The wine chiller can be freestanding  
or can be installed under the counter,  
with proper clearances.  
Do not install the wine chiller where  
the temperature will go below 55°F  
(13°C) or above 90°F (32°C).  
Allow the following clearances for ease  
of installation, proper air circulation  
and electrical connections:  
Install it on a level floor.  
Do not install the wine chiller where it  
will be subject to direct sunlight, heat  
or moisture.  
Each side  
Top  
112(38 mm)  
2(51 mm)  
2(51 mm)  
Do not store or install this appliance  
outdoors.  
Back  
Leveling Legs  
Adjustable legs at the front corners of  
the wine chiller should be set so the  
wine chiller is firmly positioned on the  
floor, with a 1/8(3 mm) tilt to the back  
to help the door closure.  
To adjust the leveling legs, turn the legs  
clockwise to raise the wine chiller,  
counterclockwise to lower it.  
To raise the wine chiller  
4
About the control and settings.  
Control Settings  
Press the CUSTOM TEMP pad. This will convert  
the RED WINE and WHITE WINE pads into temp  
up and temp down pads. Short taps to these pads  
will change the temperature setting slowly. To  
change the temperature setting more quickly,  
press and hold the pad.  
The controls give you three setting options.  
RED WINE—Use for the storage of red wines.  
This setting will provide a storage temperature  
of 55°F (13°C), which is optimum for the  
storage of red wine.  
WHITE WINE—Use for the storage of white  
wines. This setting will provide a storage  
temperature of 45°F (7°C), which is optimum  
for the storage of white wine.  
When you make your selection (WHITE WINE,  
RED WINE or CUSTOM TEMP) you will see the set  
temperature show up in the display. However,  
shortly after the selection has been made, the  
display will show the actual temperature of the  
wine chiller. You will then see the temperature  
in the display change as the actual temperature  
of the wine chiller reaches the set temperature.  
CUSTOM TEMP—This setting allows you to  
customize the temperature when storing both  
red and white wines. The custom temperature  
can be set anywhere between 40° to 65°F  
(4° to 18°C). The recommended temperature  
when storing half red wine and half white  
wine is 50°F (10°C).  
NOTE: In the event of a power failure, when the  
power is restored, the controls automatically are  
set to the RED WINE setting. If needed, reset the  
controls to the desired setting.  
Loading the Wine  
As with any refrigeration product, there is  
a slight temperature variance at different  
locations within the cabinet. In this wine  
chiller, the lower shelves provide a slightly  
cooler temperature than the upper shelves.  
When storing both red and white wines,  
it is best to store the white wine on the  
lower shelves where the temperature is  
slightly cooler.  
Suggested bottle arrangement  
When the Wine Chiller is Plugged In  
After plugging in the wine chiller and making  
your selection (WHITE WINE, RED WINE or  
CUSTOM TEMP), allow the wine chiller to reach  
the set temperature before loading your wine.  
This may take up to 12 hours to completely  
stabilize.  
After loading the wine, you may notice the  
actual temperature rise. The adjustment of  
the actual temperature reaching the set  
temperature will be reflected in the display.  
This may take up to 12 hours to completely  
stabilize.  
5
About the controls and settings.  
Locking the Controls  
This feature allows you to lock the controls so  
the temperature settings cannot be changed. The  
interior light will still function.  
To unlock the controls, simply press and  
hold the RED WINE and INTERIOR LIGHT  
pads at the same time for 3 seconds.  
To lock the controls, press and hold the  
RED WINE and INTERIOR LIGHT pads at the  
same time for 3 seconds. The word LOC  
will appear in the display to indicate the  
lockout feature has been activated. The  
display will then go back to showing the  
actual temperature. Anytime a  
temperature pad is pressed while the  
lockout feature is activated, LOC will  
appear in the display.  
Key-Ejecting Lock  
The wine chiller can be locked using the  
As a safety feature, the key for the spring-  
spring-loaded lock located above the door. loaded lock is automatically ejected and  
will not remain in the lock in either the  
open or closed position.  
Wine Chiller Light  
Press the INTERIOR LIGHT pad to turn the  
interior light on or off.  
If you turn on the light and do not turn  
it off, it will automatically turn off after  
one hour.  
Automatic Humidity Control  
The inside of the wine chiller  
automatically maintains the necessary  
level of humidity to protect wine corks  
from drying out. As a result, frost may  
form on the inner surfaces. See Care and  
Cleaning for instructions on removing  
excessive frost buildup.  
6
Care and cleaning.  
Cleaning the Outside  
IMPORTANT: Unplug the wine chiller before  
cleaning.  
Stainless steel. Regularly clean and polish  
the stainless steel areas (on some models)  
with a commercially available stainless  
steel cleaner such as Gleem-it® to preserve  
and protect the fine finish. Gleem-it® is  
available at leading hardware stores. It is  
also available through our website,  
Keep the outside clean. The cabinet can  
be washed with mild soap and water.  
Rinse thoroughly with clear water.  
Never use abrasive scouring powders.  
Use a glass cleaner or mild soap and water  
and a soft cloth to clean the glass door.  
Do not use any abrasive powders.  
1.888.261.3055. Order part number  
WX10X15.  
Do not use appliance wax or polish on the  
stainless steel.  
Wipe the control panel with a damp cloth.  
Dry thoroughly. Do not use cleaning  
sprays, large amounts of soap and water,  
abrasives or sharp objects on the panel—  
they can damage it. Some paper towels  
can also scratch the control panel.  
Protect the paint finish. The finish on  
the outside of the wine chiller is a  
high-quality, baked-on paint finish.  
With proper care, it will stay new-looking  
and rust-free for years. Apply a coat of  
kitchen/appliance wax when the wine  
chiller is new, and then at least twice  
a year.  
Do not wipe the wine chiller with a soiled  
dishcloth or towel. These may leave a residue that  
can erode the paint. Do not use scouring pads,  
powdered cleaners, bleach or cleaners containing  
bleach because these products can scratch and  
weaken the paint finish.  
Cleaning the Inside  
IMPORTANT: Unplug the wine chiller before  
cleaning.  
Do not use detergents, scouring powders,  
spray cleaners or other harsh chemicals to  
clean the interior.  
To clean the inner liner and racks, use  
a warm water and baking soda solution—  
about one tablespoon (15 ml) of baking  
soda to a quart (1 liter) of water. This  
both cleans and neutralizes odors.  
Rinse and wipe dry.  
The vinyl door gasket may be cleaned  
with mild soap and water or a baking  
soda solution. Rinse well.  
Defrosting  
Defrost whenever frost on the inside surfaces  
of the storage area becomes 1/8(3 mm) thick.  
Never use a heater of any kind, scraper or  
sharp instrument to remove frost as it may  
damage the wine chiller.  
After defrosting, make sure inside surfaces  
are dry; then return the contents to the  
wine chiller and set the temperature  
control to the desired setting.  
To defrost, unplug the wine chiller.  
Remove the contents and wipe inside  
surfaces and racks with a clean towel.  
If frost does not come off easily,  
allow the frost to melt somewhat  
and wipe off.  
7
Care and cleaning.  
In the Event of a Power Failure  
If the power fails, open the door as  
infrequently as possible to maintain  
the temperature. A gradual rise in  
temperature should not have any  
adverse effect on the wine.  
When power is restored, the controls  
automatically are set to the RED WINE  
setting. If needed, reset the controls to  
the desired setting.  
If it is extremely hot, you may want to  
unload the wine from the wine chiller and  
move the wine to a cooler location until  
power is restored.  
Preparing to Move  
Unload the wine, then secure the racks by  
taping them in place to prevent damage.  
Be sure the wine chiller stays in an upright  
position during the move.  
Replacing the light bulb.  
Unplug the wine chiller.  
If the door is locked, unlock it.  
The light bulb is located behind a light shield in the ceiling of the  
wine chiller near the front. To remove the light shield, remove the  
two screws at the back corners of the shield.  
Bulb  
Housing  
Pull down on the back of the light shield to release the two  
front tabs.  
Remove the light bulb housing by removing the two screws that  
attach the housing to the ceiling of the wine chiller.  
Step 5:  
Remove two screws  
Pull the bulb out of the receptacle. Replace with a 5 watt, 12 volt  
bulb. This type of bulb is available at most automotive parts stores.  
WARNING:  
Using a bulb rated higher than 5 watts may damage  
the electronic controls on the wine chiller.  
Attach the light bulb housing to the ceiling of the wine chiller with  
the two screws. Make sure not to pinch or damage any of the wires  
attached to the housing.  
Line up the light shield with the indentation on the ceiling of the  
wine chiller, then push the front of the shield up until the front tabs  
clip into place. Replace the screws at the back of the shield.  
Plug the wine chiller back in.  
8
Reversing the Door.  
Top cover  
Unplug the wine chiller.  
Remove the two screws at the back of the top cover.  
Lift the back of the cover up about 2(5 cm) and then slide it  
forward slightly, but do not remove.  
Remove screws  
Back of wine chiller  
Tilt the top cover on its side. Locate the power connectors at the  
front of the cover. Disconnect each connector by pressing in on  
the locking tab on the side of the connector, then pulling out.  
Set cover aside.  
Top cover  
Disconnect power  
connectors  
Front of wine chiller  
Remove screws and  
move to other side  
Carefully lay the wine chiller on its back.  
Remove the screws on the top hinge (right side). Remove the hinge.  
Remove plug button and  
move to other side  
On the opposite side, remove the screws attaching the top plate to  
the cabinet, and install them in the holes left vacant by the top  
hinge screws.  
Remove the small plug button from the top left side of the door and  
install it in the hole on the right side.  
Insert the hinge pin from the top hinge into the hole on the top left  
side of the door. Attach the top hinge to the cabinet with the screws.  
Make sure the door is aligned with the wine chiller cabinet before  
tightening the screws.  
Top of wine chiller  
Remove screws and  
top hinge, and move  
to other side  
9
Reversing the Door.  
Remove the bottom hinge by removing the screws and leveling leg.  
Remove right door  
stop and screws.  
Install left door stop  
(packed separately)  
and screws on  
Remove the right door stop and install the left door stop  
(WR13X10274), packed separately, on the opposite side.  
Remove the leveling leg and spacer on the opposite side and install  
it on the right side.  
other side  
IMPORTANT: The left leg has a spacer that must be moved to the right side  
leveling leg when the door swing is reversed.  
Remove leveling leg  
and spacer and move  
to other side  
Install the bottom hinge, with the screws and leveling leg,  
on the left side.  
Bottom of  
wine chiller  
Remove leveling  
Stand the wine chiller upright.  
leg, screws, bottom  
hinge and washer, and  
move to other side  
Open and close the door, checking the alignment of the door to the  
cabinet. If necessary, loosen the screws attaching the top hinge to  
the cabinet, realign the door and retighten the screws.  
Place the top cover on the cabinet and reconnect the power  
connections.  
Slide the top cover back in place and replace the two screws.  
Plug in the wine chiller. Reset the controls to the desired setting.  
10  
Before you call for service…  
Troubleshooting Tips  
Save time and money! Review the charts on the following  
pages first and you may not need to call for service.  
Problem  
Possible Causes  
What To Do  
Wine chiller does not  
operate and the display  
is blank  
Wine chiller is unplugged.  
Push the plug completely into the outlet.  
The circuit breaker is tripped/ Replace fuse or reset the breaker.  
the fuse is blown.  
Vibration or rattling  
(slight vibration  
is normal)  
Wine chiller is on an  
uneven surface.  
See the Leveling Legs section.  
Motor operates for  
long periods or cycles  
Normal when wine chiller  
is first plugged in.  
Wait 12 hours for the wine chiller to completely  
cool down.  
Often occurs when large  
amounts of wine are placed  
in wine chiller.  
This is normal.  
Door left open.  
Door is not self-closing. Always make sure that the  
door is closed after opening.  
Check to see if a bottle is holding door open.  
Hot weather or frequent  
door openings.  
This is normal.  
Temperature control set  
at the coldest setting.  
See About the control and settings.  
Wine chiller is too close  
to the wall.  
See the Installation Guidelines section for the  
correct clearances.  
Wine chiller too warm  
Normal when wine chiller  
is first plugged in.  
Wait 12 hours for the wine chiller to completely  
cool down.  
Often occurs when large  
amounts of wine are placed  
in wine chiller.  
This is normal.  
Temperature control  
not set cold enough.  
See About the control and settings.  
Warm weather or frequent  
door openings.  
Set the temperature control one step colder.  
See About the control and settings.  
Wine chiller is too close  
to the wall.  
See the Installation Guidelines section for the  
correct clearances.  
Door left open.  
Door is not self-closing. Always make sure that the  
door is closed after opening.  
Check to see if a bottle is holding door open.  
If the temperature setting is  
not showing what you last  
selected, a power outage  
may have occurred.  
When the power came back on, the wine chiller  
returned to the default setting, which is RED WINE.  
Reset the control to the desired setting.  
11  
Before you call for service…  
Problem  
Possible Causes  
What To Do  
Wine chiller has odor  
Interior needs cleaning.  
See Care and cleaning.  
Wipe surface dry.  
Moisture forms on  
outside of wine chiller  
Not unusual during periods  
of high humidity.  
Moisture collects inside  
Too frequent or too long  
door openings.  
(in humid weather,  
air carries moisture  
into wine chiller when  
door is opened)  
Wine bottles touching  
the back wall.  
Reposition bottles.  
Frost forms on interior  
surfaces of wine chiller  
This is normal.  
Door left open.  
See the Defrosting section.  
Excessive frost may form if the door is left open.  
See the Defrosting section.  
Door is not self-closing. Always make sure that the  
door is closed after opening.  
Check to see if a bottle is holding door open.  
Wine chiller too cold  
Temperature control  
is set too cold.  
See About the control and settings.  
If the temperature setting is  
not showing what you last  
selected, a power outage  
may have occurred.  
When the power came back on, the wine chiller  
returned to the default setting, which is RED WINE.  
Reset the control to the desired setting.  
The room temperature where  
the wine chiller is located is  
too cold.  
For proper operation, the room temperature should  
be equal to or greater than the set temperature of the  
wine chiller.  
Temperature in the  
display is not the  
temperature that  
was just set.  
This is normal.  
After you set the temperature, the display will go  
back to showing the actual temperature.  
Temperature pads do  
not respond  
Temperature pads have  
been locked.  
To unlock, simply press and hold the RED WINE  
and the INTERIOR LIGHT pads at the same time  
for 3 seconds. LOC will appear in the display when the  
temperature pads have been locked.  
Condensation on front  
of door  
Wine chiller is located in a  
high humidity environment.  
Wipe off the condensation with a clean, dry cloth.  
Locate the wine chiller in a lower humidity  
environment.  
Water on floor behind  
wine chiller  
Door left open.  
Door is not self-closing. Always make sure that the  
door is closed after opening.  
Check to see if a bottle is holding door open.  
12  
Wine Chiller Warranty.  
All warranty service provided by our Factory Service Centers, or an authorized  
®
Customer Care technician. For service call 1-800-361-3400.  
Proof of the original purchase date is needed to obtain service under warranty.  
For The Period Of:  
Camco Will Replace:  
One Year  
From the date of the  
original purchase  
Any part of the wine chiller which fails due to a defect in materials or workmanship. During this  
limited one-year warranty, Camco will also provide, free of charge, all labour and service to replace  
the defective part.  
Five Years  
From the date of the  
original purchase  
The compressor if it fails due to a defect in materials or workmanship. This additional four-year  
limited warranty does not include service labour charges or service trips to your home.  
What Camco Will Not Cover:  
Service trips to your home to teach you how to use the  
Incidental or consequential damage to personal property  
product.  
caused by possible defects with this appliance.  
Improper installation.  
Please read your Use & Care Material:  
If you then have any questions about operating the  
product, please contact your dealer or our Consumer  
Affairs office at the address below, or call toll free:  
Camco Inc.  
Failure of the product if it is abused, misused, or used for  
other than the intended purpose or used commercially.  
Loss of wine due to spoilage.  
1-800-361-3400  
Consumer Information Service  
Replacement of house fuses or resetting of circuit  
breakers  
Damage to the product caused by accident, fire, floods  
or acts of God.  
This warranty is extended to the original purchaser and any succeeding owner for products purchased for use in Canada.  
Some provinces do not allow the exclusion or limitation of consequential damages, so the above limitation or exclusion may not  
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.  
To know what your legal rights are in your province, consult your local or provincial consumer affairs office.  
Warrantor Camco Inc.  
If further help is needed concerning this warranty, write;  
Consumer Relations Manager - Camco Inc.  
1 Factory Lane, Suite 310, Moncton NB E1C 9M3  
13  
Service Telephone Numbers.  
Problem Solver 1-800-361-3400  
For answers call Camco Inc.  
Repair Service 1-800-361-3400  
Expert Camco repair service is only a phone call away.  
Service Contracts 1-800-461-3636  
Now you can have trouble-free and suprise-free service for as long  
as you own your appliance. While your warranty is still in effect,  
you can purchase a CAMCO SERVICE CONTRACT. For one low  
fee...just pennies a day...Camco Customer Service will take care of  
the repairs your appliance needs - both parts and labour.  
Parts and Accessories 1-800-263-0686  
Individuals qualified to service their own appliances can have parts  
or accessories sent directly to their homes.  
Instructions contained in this manual cover procedures to be performed  
by any user. Other servicing generally should be referred to qualified  
service personnel. Caution must be exercised, since improper servicing  
may cause unsafe operation.  
Service Satisfaction  
If you are not satisfied with the service you receive from Camco,  
follow these steps. First, contact the people who serviced your  
appliance. Next, if you are still not pleased, write all the  
details — including your phone number — to:  
Manager, Consumer Relations,  
Camco Inc., Suite 310, 1 Factory Lane,  
Moncton NB E1C 9M3  
14  

Avid Technology Pro Tools HD 7 2 User Manual
Blaupunkt 2007 User Manual
Canon 2544A003 User Manual
Canon 93515 User Manual
Canon Optura S1 User Manual
FujiFilm Camera Lens YV3 3X15SA 2 User Manual
H2O Audio AMPHIBX WA1 5A1 User Manual
Hypertec N10938PHY User Manual
Hypertec TARS0501HY User Manual
Infinity Systems Inc Car Speaker BU 2 User Manual