Toshiba B Ep800 Chg Qm R User Manual

Before using the unit, please read this manual thoroughly and retain it for future

reference.

TOSHIBA Battery Charger

B-EP800-CHG-QM-R

Owner's Manual

This symbol is intended to alert the user to the presence of

uninsulated “Dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

NOTE:

No user-serviceable parts inside. Refer servicing to qualified service personnel.

< For EU Only >

by TOSHIBA TEC CORPORATION

570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

TOSHIBA TEC Europe Retail Information Systems S.A.

Rue de la Célidée 33 BE-1080 Brussels

PRINTED IN JAPAN

EO1-33080

7FM03284000

CAUTION!

UWAGA!

1. The B-EP800-CHG-QM-R battery charger is designed and manufactured for use with the B-EP802-BT-QM-R/B-EP804-BT-QM-R

lithium-ion battery packs. There is a risk of explosion if the battery is replaced by an incorrect type.

1. Ładowarka baterii B-EP800-CHG-QM-R jest zaprojektowana i wyprodukowana do użytku z zestawami baterii litowo-jonowych B-

EP802-BT-QM-R / B-EP804-BT-QM-R. Zastosowanie nieprawidłowego typu baterii powoduje ryzyko wybuchu.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. Use only the supplied AC adapter (Model: 0225A1950) for powering this battery charger.

2. Należy używać wyłącznie dostarczonego zasilacza AC (model: 0225A1950) do zasilania tej ładowarki baterii

<Franaçis>

<한국어>

PRÉCAUTIONS!

주의!

1. 당사제품 배터리 팩 B-EP802-BT-QM-R / B-EP804-BT-QM-R 이외는 충전 하지 말아 주십시오. 다른 배터리를 사용하면 폭발의

위험이 있습니다.

1. Le chargeur de batteries B-EP800-CHG-QM-R est conçu et fabriqué pour être utilisé avec le pack batteries Lithium-ion B-EP802-

BT-QM-R/ B-EP804-BT-QM-R. Il y a un risque d’explosion si la batterie est remplacée par un modèle non adapté.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. N’utilisez que l’adaptateur secteur (Modèle: 0225A1950) pour alimenter le chargeur de batteries.

2. 본 충전기에는, 부속의 AC 어댑터 (Model: 0225A1950)이외는 접속 하지 말아 주십시오.

Achtung!

<中文（繁體字）>

注意!

1. Das Akkuladegerät B-EP800-CHG-QM-R ist speziell für die Lithium-Ionen Akku

B-EP802-BT- QM-R und B-EP804-BT-QM-R bestimmt.

Bei Verwendung eines anderen Akkus besteht die Gefahr einer Explosion.

1. 本充電器只適用与本公司所製造套装充電池B-EP802-BT-QM-R / B-EP804-BT-QM-R。更換不適當形式的電池時，持有爆發的危険

性。

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. 本充電器只適用与本機付属的電源供應器（Model: 0225A1950）。

2. Benutzen Sie nur das mitgelieferte Ladegerät (Model: 0225A1950) um den Akku zu laden.

<Español>

ATENCIÓN!

1. El cargador de baterías B-EP800-CHG-QM-R se ha diseñado y fabricado para usar junto con las baterías de Litio-Ión B-EP802-

BT-QM-R / B-EP804-BT-QM-R. Existe riesgo de explosión si se usa un tipo de batería incorrecto.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. Utilice solo el adaptador AC suministrado (Modelo: 0225A1950) para alimentar este cargador de baterías.

WAARSCHUWING!

1. De B-EP800-CHG-QM-R batterijlader is uitsluitend geschikt voor de B-EP802-BT-QM-R/ B-EP804-BT-QM-R lithium-ion

batterijeenheid. Vervanging door een verkeerd type batterij kan een ontploffing veroorzaken.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. Gebruik uitsluitend de bijgeleverde wisselstroomadapter (Model: 0225A1950) om de batterijlader te voeden.

ATTENZIONE!

1. Il caricabatterie del modello B-EP800-CHG-QM-R e esclusivamente per il modello B-EP802-BT-QM-R/ B-EP804-BT-QM-R pacco

batterie Ioni di Litio. Esiste il rischio di esplosine se utilizzate le batterie sbagliate.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. Utilizzate solo l’adattatore per corrente alternate (Modello: 0225A1950) per alimentare il caricabatterie.

<Português>

ATENÇÃO!

1. O carregador de bateria B-EP800-CHG-QM-R foi desenhado e fabricado para uso com as baterias de Lithium-ion B-EP802-BT-

QM-R/ B-EP804-BT-QM-R. Existe o risco de explosão se a bateria for substituída por um tipo de bateria incorrecto.

B-EP2DL-GH20-QM-R

B-EP2DL-GH30-QM-R

B-EP2DL-GH40-QM-R

B-EP4DL-GH20-QM-R

B-EP4DL-GH30-QM-R

B-EP4DL-GH40-QM-R

B-EP802-BT-QM-R

B-EP804-BT-QM-R

2. Utilize apenas o adaptador AC fornecido (Modelo: 0225A1950) para ligar este carregador de bateria à corrente eléctrica.

5. Insert the battery pack into the slot in the

orientation shown below.

The CHARGE lamp will light up and charging

will begin.

Battery Pack

To Charge the Battery Pack

WARNING!

1. The B-EP800-CHG-QM-R battery charger is designed for charging the B-EP802-

BT-QM-R/ B-EP804-BT-QM-R lithium-ion battery packs. DO NOT charge any

other battery packs, or explosion, combustion, or overheating may result.

2. If the battery charger gives out smoke, a bad smell, or extraordinary heat,

immediately unplug the power cord from the AC outlet. Failure to do this may

cause fire or electric shock.

CHARGE Lamp

Partition

NOTE:

Insert an appropriate size of the battery pack

according to the partition’s orientation.

Failure to do this may damage the battery

pack or affect charging operation.

Please use the following procedure to charge a battery pack (B-EP802-BT-QM-R/B-

EP804-BT-QM-R).

The CHARGE lamp indicates a charging status.

1. Fit the partition into the slot. The orientation of the partition differs depending on

the battery pack size (B-EP802-BT-QM-R or B-EP804-BT-QM-R) to be charged.

CHARGE lamp

OFF

Red

Green

Blinking red

State

Unconnected.

Charged.

Completed.

Abnormal state

NOTE:

When charging B-EP802-BT-

QM-R battery pack

Tab

When charging B-EP804-BT-QM-R

battery pack

Tab

The green light does not go off until the

battery pack is removed from the slot.

6. After charging is completed, remove the battery pack from the battery charger.

7. Disconnect the power cord from the AC outlet.

Charging time

To charge an empty battery pack:

NOTE:

• Fit the partition in the correct position and orientation and make sure the tabs

Battery pack

B-EP802-BT-QM-R

Charging time

are fit into the holes.

about 3 hours

• Be careful not to lose the partition.

• Care must be taken not to mistake the orientation, as the partition cannot be

removed once it is fitted.

(Until the min. of 85% of the nominal capacity is charged.)

B-EP804-BT-QM-R

about 3 hours

(Until the min. of 85% of the nominal capacity is charged.)

2. Connect the AC adapter to the battery

charger.

•Charging time may differ depending on the condition of the battery pack or the

operating temperature.

•After the CHARGE lamp turns from red to green, the battery charger may

continue to charge the battery pack for up to one more hour until the full charge

level (95% or more).

Battery Charger

3. Connect the power cord to the AC

adapter.

4. Connect the power cord to an AC

outlet.

Power Cord

AC Adapter

NOTES:

1. Battery packs should be charged on condition that both ambient temperature and

battery temperature fall within a range of 0 °C to 40°C.

2. The battery charger will get warmer during charging (room temperature + about

30°C). This is not abnormal.

3. If the over discharge protector has been operated on a battery pack, the

CHARGE lamp may not light for a while. Leave the battery charger and the battery

pack alone for a few minutes. Stop using the battery pack if the CHARGE lamp

does not light at all as the battery pack may be faulty.

4. The battery pack can be removed from the battery charger while charging is in

progress. However, the battery lasting time depends on the charging time.

5. After the charging is completed, do not leave the battery pack in the charger too

long. The battery pack gradually discharges.

TROUBLESHOOTING

If you have any problems while using this product, please check the following point

first.

If a problem cannot be solved by taking actions described below, unplug the battery

charger and contact the dealer or an authorised TOSHIBA TEC service

representative for assistance.

Symptom

Cause and resolution

A battery pack is loaded in • The power cord is not connected properly.

the battery charger, but

the CHARGE lamp does

not light up in red.

⇒Firmly connect the power cord to the AC

adapter and the AC outlet.

• The terminals of the battery charger or the battery

electrodes are stained.

⇒Wipe clean those portions with a soft dry cloth.

• You are attempting to charge a battery pack with the

over discharge protection activated (The CHARGE

lamp may not light up immediately after loading a

battery.)

6. Periodically clean the charger terminals with a soft dry cloth.

⇒Leave the battery charger and the battery pack

alone for a few minutes. If the CHARGE lamp does

not light after all, stop using the battery pack, as the

battery pack may be faulty.

• The partition is not fitted.

⇒Fit the partition in the correct orientation.

The CHARGE lamp blinks • A battery pack failure is detected.

in red.

⇒It could be the end of battery life. Replace the

battery pack with a new one.

Charging time overruns

the approximate specified

time.

• Charging time varies depending on the condition of

the battery pack, ambient temperature, etc.

⇒If the battery charger continues charging even

after the specified time has passed, stop

charging and replace the battery pack with a

new one.

Battery pack does not last • It could be the end of battery life.

long time though the

⇒Replace the battery pack with a new one.

battery is fully charged.

The battery pack cannot

be inserted into the slot.

• The partition is not set completely.

⇒Fit the partition completely.

Specifications

When purchasing the power cord:

Item

Battery charger

AC Adapter(Accessory)

Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following

standard from your authorized TOSHIBA TEC representative.

(As of August 2008)

Model

B-EP800-CHG-QM-R

0225A1950(B-EP800-AC-

QM-R)

Certification

Country

Agency

SAA

Country

Agency Certification mark

VDE

Country

Agency

Certification mark

mark

Power requirements

DC +19V, 2.63A (Supplied by 100 to 240V AC, 50/60 Hz

the AC adapter)

Australia

Germany

Sweden

SEMKKO

Output voltage

Application

---

TOSHIBA TEC battery pack

B-EP802-BT-QM-R

B-EP804-BT-QM-R

1 slot

DC+19V, 2.63A

Austria

Belgium

Canada

OVE

CEBEC

CSA

Ireland

Italy

NSAI

IMQ

Switzerland

SEV

ASTA

BSI

TOSHIBA Battery Charger

B-EP800-CHG-QM-R

Japan

METI

KEMA

Number of slots

---

The battery pack model is

automatically sensed.

Denmark

DEMKO

Netherlands

U.S.A.

Operating temperature

Operating humidity

Storage temperature

Storage humidity

Dimensions

0°C to 40°C (32°F to 104°F)

Finland

France

FEI

Norway

Spain

NEMKO

AEE

Europe

China

HAR

CCC

20 to 80% (no condensation)

-20°C to 60°C (-4°F to 140°F)

10 to 85% (no condensation)

UTE

Power Cord Instruction

85 x 67 x 77 mm (w/h/d)

(3.35” x 2.64” x 3.03”)

42 x 29.2 x 98 mm (w/h/d)

(1.65” x 1.15” x 3.86”)

1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A.

2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V.

3. Please select a power cord with the length of 2m or less.

4. The power cord plug connected to the AC adapter must be able to be inserted to an ICE-320-C6 inlet. Refer to

the following figure for the shape.

excluding the projecting parts excluding the projecting

parts

Weight

Approx. 195 g (6.9 oz)

(Excluding the accessories)

Approx. 250 g (8.8 oz)

United

Country/Region

North America

Europe

250V

Australia

China

250V

Accessories

AC adapter x 1, Partition x 1, Owners Manual x 1

Kingdom

Power Cord

Rated (Min.)

Type

125V, 10A

SVT

250V

H05VV-F

250V

NOTE: Design and specifications are subject to change without notice.

H05VV-F

AS3191 approved,

Light or Ordinary Duty type

3 x 0.75 mm²

GB5023

Conductor size

(Min.)

No. 3/18AWG

3 x 0.75 mm²

Plug Configuration

(locally approved

type)

Rated (Min.)

125V, 10A

250V, 10A

250V, *1

*1: At least, 125% of the rated current of the product.

Siemens Gigaset Sx205 User Manual
Sharp Ar 810 User Manual
Samsung As12hpbn User Manual
NEC NP ME301W User Manual
NEC MULTISYNC P462 02 User Manual
MAKITA HP2071 User Manual
KENWOOD IM200 User Manual
FUJITSU TWAIN 32 02 User Manual
CRAFTSMAN 580.761800 User Manual
BROTHER FAX 275 User Manual