Test Products International 505 User Manual

505  
TM  
The Value Leader  
PHOTO / CONTACT  
TACHOMETER  
Instruction Manual  
505 Instruction Manual  
Test Products International, Inc.  
9615 SW Allen Blvd  
Beaverton, OR 97005-4814 USA  
Ph: 503-520-9197 Fax: 503-520-1225  
Test Product International Ltd.  
342 Bronte Street South, Unit 9  
Milton, Ontario L9T 5B7  
Ph: 905-693-8558 Fax: 905-693-0888  
Test Products International UK Ltd.  
Longley House, East Park  
Crawley, West Sussex RH10 6AP  
Ph: +44 (0) 1293 561212 Fax: +44 (0) 1293 813465  
copyright © 2006, Test Products International, Inc  
PHOTO TACH OPERATION  
Measurement Procedure:  
BATTERY REPLACEMENT  
Measurement Procedure:  
1. Unscrew contact collar from optical end of  
505 (if attached).  
1. Remove the screw holding the battery compart-  
ment cover in place on the back of the 505.  
2. Slide the cover off of the unit.  
3. Remove the 2 each “AA” alkaline batteries and  
replace with the same type.  
2. Attach a piece of reflectIive tape on the rotating  
object to be measured.  
3. Depress and hold the START button and then  
press the Photo button (lower right) on the  
505.  
4. Replace the cover and screw.  
4. With the start button depressed, point the  
optical end at the rotating surface so the  
relective tape passes the lens every rotation.  
5. Read the RPM on the LCD display.  
STANDARD ACCESSORIES  
Memory Recall  
Reflective Tape . . . . . . . . . . . . . . . . . . . . . . .A501  
Contact RPM Adapter (screw on) . . . . . . . . .A502  
RPM Adapter (Cone Type) . . . . . . . . . . . . . .A503  
RPM Adapter (Funnel Type) . . . . . . . . . . . . .A504  
Surface Speed Test Wheel . . . . . . . . . . . . . .A505  
(O.D. 48.7 mm exactly)  
Note: The memory resets itself once the START  
button is depressed and stable measurements  
are displayed for 10 seconds or 12 revolutions  
(whichever is longer). The values are stored  
when the START button is released.  
Carrying case . . . . . . . . . . . . . . . . . . . . . . . .A915  
1. When you are finished taking measurements,  
release the START button.  
2. Depress the MEMORY button once, the LAST  
reading will be displayed  
3. Press the MEMORY button twice, the MAX  
reading will be displayed.  
4. Press the MEMORY button three times, the MIN  
reading will be displayed.  
Unit will auto power off after 5 seconds.  
6
3
SURFACE SPEED OPERATION  
Measurement Procedure:  
CONTACT TACH OPERATION  
Measurement Procedure:  
1. Screw the shaft assembly to the optical end of  
the 505.  
1. Screw the shaft assembly to the optical end of  
the 505.  
2. Insert the cone or concave wheel that more  
closely matches the end of the component to  
be measured on the shaft assembly.  
3. Press and hold the START button and then  
press the Contact button (lower left) on the  
505.  
4. While pressing the START button, hold the  
wheel against the end of the rotating shaft..  
5. Read the RPM on the LCD.  
2. Insert the large wheel to the end of the shaft  
assembly.  
3. Press and hold the START button and then  
press the ft/min (feet per minute) or m/min  
(meters per minute) on the 505.  
4. While pressing the START button, hold the  
wheel against the moving surface.  
5. Read the speed on the LCD.  
Memory Recall  
Memory Recall  
Note: The memory resets itself once the START  
button is depressed and stable measurements  
are displayed for 10 seconds or 12 revolutions  
(whichever is longer). The values are stored  
when the START button is released.  
Note: The memory resets itself once the START  
button is depressed and stable measurements  
are displayed for 10 seconds or 12 revolutions  
(whichever is longer). The values are stored  
when the START button is released.  
1. When you are finished taking measurements,  
release the START button.  
2. Depress the MEMORY button once, the LAST  
reading will be displayed  
3. Press the MEMORY button twice, the MAX  
reading will be displayed.  
4. Press the MEMORY button three times, the MIN  
reading will be displayed.  
1. When you are finished taking measurements,  
release the START button.  
2. Depress the MEMORY button once, the LAST  
reading will be displayed  
3. Press the MEMORY button twice, the MAX  
reading will be displayed.  
4. Press the MEMORY button three times, the MIN  
reading will be displayed.  
Unit will power off after 5 seconds.  
Unit will power off after 5 seconds.  
4
5

Schumacher Sf 1250 User Manual
Schumacher Sc 200a User Manual
Sanyo Sap91kc User Manual
Mitsubishi Motors Automobile Parts 13a 0 1 User Manual
HARPER GAMING TANGO GKB P100 User Manual
D LINK AV500 DHP W310AV User Manual
DELL WYSE 5000 W11B User Manual
Cub Cadet 221 Lhp Engine Operator's User Manual
CRAFTSMAN CMXEVBE176120 User Manual
CANON POWERSHOT G1 X User Manual