P3PC-6112-03EN
fi-760PRB Imprinter
Operator’s Guide
Introduction
Thank you for your purchase of the fi-760PRB Imprinter.
The fi-760PRB Imprinter is an optional unit to be used
with the fi-7600 image scanner.
This manual explains installation and connection, basic
operations, and regular maintenance of the fi-760PRB
Imprinter. Use the product correctly according to this
manual.
For how to use the fi-7600 image scanner, refer to
"fi-7600/fi-7700/fi-7700S Image Scanner Operator's
Guide" contained in the setup DVD-ROM included in the
package.
We hope that this manual helps you make the most of
the imprinter.
Abbreviations Used in This Manual
The operating systems and products in this manual are
indicated as follows.
Name
Indication
®
Windows
Server 2008
R2 (*1)
Windows Server 2008 R2 Standard
(64-bit)
®
Windows 7
(*1)
Windows 7 Professional (32-bit/64-
bit)
®
Windows 7 Enterprise (32-bit/64-bit)
®
February 2022
Windows
Server 2012
(*1)
Windows Server 2012 Standard
(64-bit)
Safety Information
®
Windows
Server 2012
R2 (*1)
Windows Server 2012 R2 Standard
(64-bit)
The "Safety Precautions" manual that is supplied with
the scanner contains important information about the
safety and the correct way of using this product. Make
sure that you read and understand it before using this
product.
®
Windows 8.1
(*1)
Windows 8.1 (32-bit/64-bit)
®
Windows 8.1 Pro (32-bit/64-bit)
®
Windows 8.1 Enterprise (32-bit/64-bit)
®
Windows 10
(*1)
Windows 10 Home (32-bit/64-bit)
Manufacturer
®
Windows 10 Pro (32-bit/64-bit)
PFU Limited
®
YOKOHAMA i-MARK PLACE, 4-5 Minatomirai
4-chome, Nishi-ku, Yokohama-shi, Kanagawa 220-8567
Japan.
Windows 10 Enterprise (32-bit/64-bit)
®
Windows 10 Education (32-bit/64-bit)
®
Windows
Server 2016
(*1)
Windows Server 2016 Standard
© PFU Limited 2017-2022
(64-bit)
Trademarks
®
Windows
Server 2019
(*1)
Windows Server 2019 Standard
(64-bit)
PaperStream is a registered trademark of PFU Limited
in Japan.
Other company names and product names are the
registered trademarks or trademarks of the respective
companies.
®
Windows
Server 2022
(*1)
Windows Server 2022 Standard
(64-bit)
®
Windows 11
(*1)
Windows 11 Home (64-bit)
®
Windows 11 Pro (64-bit)
®
Windows 11 Enterprise (64-bit)
®
Windows 11 Education (64-bit)
PaperStream IP (TWAIN)
PaperStream IP (TWAIN ×64)
PaperStream IP (ISIS) Bundle
PaperStream
IP driver
fi-760PRB Imprinter
imprinter
scanner
fi-7600 image scanner
fi-7600/fi-7700/fi-7700S Image
Scanner Operator's Guide
Operator's
Guide
*1: Where there is no distinction between the different
versions of the above operating system, the general
term "Windows" is used.
2
Arrow Symbols in This Manual
Right-arrow symbols () are used to separate icons or
menu options you should select in succession.
Click [Start] menu [Control Panel].
Screen Examples in This Manual
Microsoft product screenshots are reprinted with
permission from Microsoft Corporation.
The screen examples in this manual are subject to
change without notice in the interest of product
development.
If the actual displayed screen differs from the screen
examples in this manual, operate by following the actual
displayed screen while referring to the user's manual of
the scanner application that you are using.
The screenshots used in this manual are of Windows 7
or Windows 10. The actual windows and operations may
differ depending on the operating system. Also note that
with some scanner models, the screens and operations
may differ from this manual when you update the
software. In that case, refer to the manual provided upon
updating the software.
3
Chapter 1 Preparations
■ Imprinter with Scanner
1.1 Checking the Package Contents
Front
Check the package contents list that is included in the
imprinter package box to make sure that all items are
included in the package.
ADF Paper Chute
(Feeder)
ADF (Automatic
Document Feeder)
If anything is missing or damaged, contact your
FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Stacker
Use this product and accessories carefully.
1.2 Names of Component Parts
■ Imprinter Unit
Front
Print Cartridge
Cover
When the operator panel
is fitted into the side of
the scanner
Operator Panel
The scanner has an operator panel on each side.
LCD
[Menu] Button
Print Section
[] Button/[] Button
[Stop/Clear] Button
[Scan/Enter] Button
[Power] Button
Back
Back
Lock
Lock
EXT Cable
■ Attachment Guide
4
■ Inside
Paper Guide
Print Cartridge Holder
Print Cartridge Cover
5
Chapter 2 Installation
2
Look into the scanner from below to check the
position of the bar.
2.1 Installing the Imprinter
Install the imprinter as follows:
Bar
ADF
ATTENTION
Do not move the scanner with the imprinter
installed. The imprinter may be damaged.
1
2
Turn off the scanner power and disconnect the
power cable.
3
Align the attachment guide with the bar.
Remove the stacker from the scanner.
1
Check that the stacker is placed in the lower position.
You can lower the position of the stacker by tilting it
upwards a little.
1
2
Hold the center (
) of the stacker and slightly
2
bend it to remove the right side (
) of the stacker
Bar
from the slot in the direction of the arrow.
1
Attachment Guide
4
Lift the attachment guide from underneath to attach
it.
2
ATTENTION
You must remove the stacker before installing the
imprinter.
Do not pull forcibly, since this might damage the
stacker.
3
Attach the attachment guide to the scanner.
1
Make sure that the direction of the attachment guide
is the same as direction shown in the following figure.
Attachment Guide
ADF
6
ATTENTION
Confirm the following after attaching the attachment guide.
The attachment guide is not tilted.
The attachment guide is fitted in the scanner, and not
overhanging.
Good: The attachment guide is properly attached.
Bad: The attachment guide is tilted.
After
Installation
Bad: The attachment guide is overhanging.
ATTENTION
Be careful not to get your fingers caught.
5
Raise the locks (two locks on the back side).
HINT
Removing the Attachment Guide
To remove the attachment guide, press your fingers
against the attachment guide and slide it
downward.
4
Attach the scanner onto the imprinter.
Hold the scanner above the rear of the imprinter
and gently lower it onto the base of the imprinter
until it fits in place.
7
6
7
Turn the locks inside (two locks on the back side).
2.2 Loading the Print Cartridge
Load the print cartridge as follows:
ATTENTION
When installing the print cartridge, install it
properly.
When you do not use the imprinter for a long time,
remove the print cartridge from the imprinter. Ink
will be consumed every time the scanner is
powered-on even if printing is not done.
Connect the EXT cable to the connector on the
back of the scanner.
1
2
Turn off the scanner.
Place your hand in the middle part of the print
cartridge and open it as shown below.
ATTENTION
The imprinter will not work if the EXT cable is not
connected to the scanner. Scanning when the EXT
cable is not connected can cause documents to
jam inside the imprinter.
3
4
Remove the tape that holds the print cartridge
holder and the paper guides.
Lift the print cartridge holder by pinching the lever
with your fingers as shown below.
8
Install the stacker removed from the scanner (in
procedure 2) to the imprinter.
Insert the protrusion on the right side of the stacker
into the slot 1 and then push the left side of the
stacker along the slot 2 in the direction of the
arrow.
2
1
5
Take out the print cartridge from the bag.
9
Connect the power cable to the scanner.
8
6
Remove the protection tape on the print cartridge.
9
Move the print cartridge to an appropriate printing
position.
The print cartridge should be positioned within the
section where the document will pass through.
ATTENTION
Do not touch the metal part of the print cartridge nor put the
tape back again.
10 Close the print cartridge cover.
7
With the tab on the print cartridge facing right, put
the print cartridge into the holder.
ATTENTION
Be careful not to let the print cartridge catch the
print circuit film to avoid damaging the film.
Print Circuit
Film
8
Bring down the arm of the print cartridge holder
down gently until it locks in and set the print
cartridge in place.
Make sure that the catches (both sides) on the arm
latch onto the print cartridge firmly.
Catches
9
5
6
Select [1: Single Sheet Only] or [2: Multiple Sheets]
2.3 Test Print
by pressing the [] button or the [] button, and
then confirm the selection by pressing the [Scan/
Enter] button.
After loading the print cartridge, check if the printing
operation works normally.
When [2: Multiple Sheets] is selected, printing is
performed for all sheets set in the scanner.
HINT
For details about the operator panel, refer to the
Operator's Guide provided with the scanner.
The [Print Pattern] screen is shown on the LCD.
Select a print pattern by pressing the [] button or
the [] button, and then confirm the selection by
pressing the [Scan/Enter] button.
1
Push the [Power] button of the operator panel of the
scanner.
The [Ready] screen is shown on the LCD.
HINT
Below are the print test patterns:
2
Load a blank document in the scanner.
Test Pattern 1 (Horizontal):
HINT
ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_`0000
0000
Test Pattern 2 (Horizontal):
Use A3 or Double Letter size blank paper. If the
paper size is smaller, printing may not be
completed successfully.
abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
Test Pattern 3 (Horizontal):
Confirm that the print cartridge is positioned within
the document width.
!"#$%&'()*+,-./0123456789:;<=>?@00000000
Test Pattern 4 (Vertical):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_`0000
0000
Test Pattern 5 (Vertical):
abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
Test Pattern 6 (Vertical):
!"#$%&'()*+,-./0123456789:;<=>?@00000000
The numbering section "00000000" increases in
increments of one, starting from 0 (zero).
6
5
4
3
3
Press the [Menu] button.
Menu
Stop/Clear
Scan/Enter
Check
Power
2
1
The [Settings Menu] screen is shown on the
5 mm
LCD.
4
Select [3: Test Print] by pressing the [] button or
the [] button, and confirm the selection by
pressing the [Scan/Enter] button.
The [No. of Sheets Scanned] screen is shown
Test Pattern Print Sample
on the LCD.
The [Test Print] screen is shown on the LCD.
ATTENTION
If the Imprinter is disconnected or not connected
properly, [Cannot use this function because the
Imprinter is not connected.] is shown on the LCD.
10
7
8
Select [1: Yes] by pressing the [] button or the
[] button, and then confirm the selection by
pressing the [Scan/Enter] button.
The blank sheet is fed into the scanner, and the
imprinter will print out a print test pattern leaving
a 5 mm gap (with an allowance of 4 mm inwards
or outwards) from the edge of the document.
To finish the print test, press the [Power] button on
the operator panel of the scanner to turn off the
power of the scanner.
ATTENTION
Do not move the imprinter or give it a jolt while
printing. Printing may be out of order.
11
Chapter 3 Basic Operation
3.1 Setting the Print Position
3.2 Using the Paper Guides
Set the print position in the following steps:
When documents have curled edges like below, use the
paper guides to prevent paper jams.
1
2
Open the print cartridge cover.
Move the print cartridge to an appropriate printing
position.
Hold the print cartridge as below, and slide it to the
left or right within the document width to set it at a
suitable print starting position.
Document Feed
Direction
Move the paper guides to the positions where the edges
of documents pass through in the following steps:
1
2
3
Load documents in the scanner.
Open the print cartridge cover.
Slide the paper guides and align them with the
edges of the document.
HINT
The triangle-shaped protrusion on the print
cartridge holder indicates the print head. Use the
protrusion as a guide for the print position.
You can find the document size markings on the
imprinter above the print cartridge. Use the
markings as a guide for the document width.
Load the actual document in the scanner and
make sure that the print cartridge is positioned
within the width of document.
Paper Guides
ATTENTION
Be careful not to let the paper guides come into
contact with the print circuit film to avoid damaging
the film.
Print Circuit
Film
3
Close the print cartridge cover.
12
2
Push the head of the paper guide until it fits in well.
HINT
When you want to perform a print on the left or right
margin of a wide document, the paper guide may
get in the way. In this case, remove the paper guide
and attach it to a place near the center where
1
space is available (
). After that, move the print
cartridge to the left or right margin ( 2 ).
When the print position is on the right margin
2
Paper Guide
&ꢁꢁꢂꢃ$
%/$&.
1
When the print position is on the left margin
2
& ꢁ ꢁ ꢂ ꢃ $
%
1
■ Removing the Paper Guides
To remove the paper guides, pinch the paper guide with
your fingers and pull it out as shown below.
Paper Guide
■ Attaching the Paper Guides
1
Place the paper guide as shown in the figure below.
Make sure that the paper guide is under the metal
wheel.
Paper Guide
Metal Wheel
13
3.3 Print Setup
3.4 Replacing the Print Cartridge
You can configure settings for the imprinter by using the
scanner driver's setup window.
The print cartridge is a consumable.
Replace the print cartridge as follows:
ATTENTION
HINT
When the following message appears, replace the
print cartridge as soon as possible. If you continue
to print without replacing the cartridge, your print
output will be faded.
How to run the scanner driver differs depending on
the application.
For details, refer to the manual or help of the
application being used.
HINT
The following items can be specified. For details,
refer to the help of the PaperStream IP driver.
Imprinter status (on or off)
Whether or not the setup dialog box is displayed
Whether the PaperStream IP driver is
synchronized with the Digital Endorser
Printing settings (such as font type, direction, the
print starting position, character strings to be
printed, and initial, increased and decreased
values for the counter)
When replacing the print cartridge, make sure it is
installed properly.
1
2
Turn off the scanner.
Place your hand in the middle part of the print
cartridge and open it as shown below.
3
Lift the print cartridge holder by pinching the lever
with your fingers as shown below.
14
4
5
Remove the old print cartridge.
7
Bring down the arm of the print cartridge holder
down gently until it locks in and set the print
cartridge in place.
Make sure that the catches (both sides) on the arm
latch onto the print cartridge firmly.
Catches
Remove the protection tape on the new print
cartridge.
8
Move the print cartridge to an appropriate printing
position.
The print cartridge should be positioned within the
section where the document will pass through.
ATTENTION
Do not touch the metal part of the print cartridge nor
put the tape back again.
6
With the tab on the print cartridge facing right, put
the print cartridge into the holder.
ATTENTION
Depending on the position of the print cartridge,
printing may not fit within the document when
printing close to the document edge.
9
Close the print cartridge cover.
ATTENTION
Be careful not to let the print cartridge catch the
print circuit film to avoid damaging the film.
Print Circuit
Film
10 Turn on the scanner.
15
11 Reset the ink counter in the following procedure.
3.5 Removing Jammed Documents
If a document jams, remove the jammed document as
follows:
ATTENTION
Be sure to reset the ink counter after replacing the
print cartridge.
ATTENTION
Open the ADF and the print section to remove the
jammed document. Do not pull out the document
forcefully.
1
Display the [Software Operation Panel] window.
Windows Server 2008 R2/Windows 7
Click [Start] menu [All Programs] [fi Series]
[Software Operation Panel].
Windows Server 2012
1
2
Remove the documents from the ADF paper chute
(feeder).
Right-click the Start screen, and select [All apps] on
the app bar [Software Operation Panel] under [fi
Series].
Hold the middle part of the print section, and open it
as shown in the figure.
Windows Server 2012 R2/Windows 8.1
Click [] on the lower left side of the Start screen and
select [Software Operation Panel] under [fi Series].
To display [], move the mouse cursor.
Windows 10/Windows Server 2016/Windows
Server 2019/Windows Server 2022
Click [Start] menu [fi Series] [Software
Operation Panel].
Windows 11
Click [Start] menu [All apps] [fi Series]
[Software Operation Panel].
2
Click [Device Setting] from the list on the left, and
then click the [Clear] button of [Remaining Ink].
ATTENTION
When you open the ADF, be sure to open the print
section beforehand.
3
Open the ADF.
ADF
Print
Section
The value of the counter is set to 100.
3
4
Click the [OK] button on the [Software Operation
Panel] window.
A message appears. Click the [OK] button.
The [Software Operation Panel] window closes,
and the ink counter is cleared.
4
Remove the jammed document.
16
5
Close the ADF.
ADF
Print
Section
6
Hold the middle part of the print section, and close it
as shown in the figure.
ATTENTION
Make sure that the ADF is closed before you close
the print section.
Be careful not to get your fingers caught.
17
Chapter 4 Daily Care
4.1 Cleaning the Print Cartridge
4.2 Cleaning the Imprinter
Ink stains stuck to the nozzle plate of the print cartridge
or leaving the imprinter unused for a while may cause
poor print quality due to a clogged nozzle. If your
imprinter has these types of trouble, clean the nozzle
While you use the imprinter frequently, ink sticks to the
print cartridge holder base which makes the paper dirty.
As a part of daily maintenance, clean the print cartridge
holder base by following the procedure below.
plate of the print cartridge.
ATTENTION
When cleaning, use an absorbent cloth or a waste
cloth, and gently wipe off the ink.
If the ink is dried, gently wipe it with a moistened
cloth. (Since the ink is water soluble, it can be
cleaned with water.)
ATTENTION
For cleaning, use a dry lint-free cloth, and gently
wipe off the excess ink from the surface of the
nozzle plate. (Do not use a tissue.)
HINT
1
2
Turn off the scanner.
If the nozzle is still clogged after cleaning the print
cartridge, replace it with a new cartridge.
Remove the print cartridge.
14).)
1
2
Turn off the scanner.
3
4
Open the print section.
Remove the print cartridge.
Clean the print cartridge holder base by pressing a
cloth or a waste cloth gently on it to wipe off the ink.
14).)
Nozzle Plate
Contact Part
ATTENTION
Be careful not to touch the nozzle plate or the
contact part with your hand as this may cause poor
print quality or contact errors.
3
Wipe off the excess ink on the nozzle plate gently.
ATTENTION
When cleaning, be careful not to touch the metal
wheels located at the print section.
4
Make sure that the excess ink is removed and then
reinstall the print cartridge.
14).)
5
Confirm that the ink is removed and then close the
print section.
ATTENTION
When installing the print cartridge, install it
properly.
6
Reinstall the print cartridge.
14).)
18
3
Clean the plastic rollers.
4.3 Cleaning the Rollers
Clean the two plastic rollers (black) at the print
section.
When ink or paper dust is stuck on the imprinter feed
roller surfaces, documents may not feed smoothly.
To prevent feed problems, clean the roller surfaces
regularly.
Plastic Rollers
ATTENTION
It may take a long time to dry if an excessive
amount of Cleaner F1 is used. Use it in small
quantity. Wipe off the cleaner completely to leave
no residue on the cleaned parts.
HINT
The recommended cleaning cycle is every 5,000
sheets. The actual cleaning cycle may be shorter
depending on how often the imprinter is used and
the documents.
Print Section
Rotate the rollers manually while gently wiping the
dirt and dust off the surface of the rollers with a
cloth moistened with Cleaner F1.
4
Confirm that the dirt is removed and then close the
print section.
1
2
Open the print section.
Clean the rubber rollers.
4.4 Cleaning Materials
Clean the rubber rollers (eight in total) under the
feeding section.
Name
Cleaner F1
Part No.
Notes
Rubber Rollers
PA03950-
0352
Volume: 100 ml
Cleaning Wipe
PA03950-
0419
24 packets
(*1)
Print Section
Gently wipe the dirt and dust off the surface of the
rollers with a cloth moistened with Cleaner F1.
Clean the entire surface of the rubber rollers as you
rotate them manually.
*1: Pre-moistened with Cleaner F1. It can be used
instead of moistening a cloth with Cleaner F1.
ATTENTION
ATTENTION
In order to use the cleaning materials correctly and
safely, read the precautions on each product
thoroughly.
When cleaning, be careful not to touch the metal
wheels located at the print section.
For information about the cleaning materials, contact
your FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
19
Chapter 5 Error Messages
This chapter explains the imprinter error messages.
Error codes and error messages are displayed on the LCD. Refer to the error codes and the error messages that are
displayed for troubleshooting.
HINT
For details on the error messages and other errors, refer to the Operator's Guide provided with the scanner.
Error Code
J1:5A
Error Details
Paper jam (Imprinter)
Action
Try the following:
1. Remove the jammed document from the imprinter.
2. Make sure that the document is an appropriate one for scanning
with the imprinter.
3. Clean the rollers.
Imprinter Cover Open
Close the print section of the imprinter, and load the document again.
U5:4A (*1)
U6:B4
Print cartridge not installed
No print cartridge is installed.
Check if the print cartridge is installed correctly.
Imprinting area error
Adjust the imprinting start position and the imprinter strings to fit the
imprinting area in the document.
U7:B9
Imprinter error (communication timeout) An error occurred in the imprinter.
A1:B3
A3:B6
A4:B8
Try the following:
Imprinter error (EEPROM)
1. Confirm that the EXT cable of the imprinter is connected properly
to the EXT connector on the back of the scanner.
Imprinter error (ROM)
2. Check if the print cartridge is installed correctly.
3. Turn the scanner off then back on.
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Imprinter error (print head)
An error occurred in the imprinter.
Try the following:
A2:B5
1. Confirm that the EXT cable of the imprinter is connected properly
to the EXT connector on the back of the scanner.
2. Check if the print cartridge is installed correctly.
3. If you have a new print cartridge, replace the old print cartridge with
the new one.
4. Turn the scanner off then back on.
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Imprinter system error
An error occurred in the imprinter.
Turn the scanner off then back on.
H6:B1
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
*1: When you open the imprinter print section while the scanner is in standby, only an error message will appear without
an error code. Also, note that buttons on the operator panel are disabled while the imprinter print section is open.
20
Chapter 6 Specifications
Item
Specification
Thermal inkjet printing
Printing Method
Post printing, back surface printing
Print Timing
Alphabet:
Numeric characters: 0, 1 to 9
A to Z, a to z
Printing Characters
Symbols:
! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ ¥ ] ^ _ ` { | } ¯
Maximum of 43 digits
Maximum Number
of Characters per
Line
Normal, Bold:
Narrow:
0°, 180° (horizontal), 90°, 270° (vertical)
0°, 180° (horizontal)
Print Orientation
Character Size
Normal, Bold:
Height 2.91 × width 2.82 mm/0.1146 × 0.1110 in. (horizontal orientation),
Height 2.82 × width 2.91 mm/0.1110 × 0.1146 in. (vertical orientation)
Height 2.91 × width 2.12 mm/0.1146 × 0.0835 in. (horizontal orientation)
Narrow:
3.53 mm/0.1390 in. (Normal, Bold), 2.54 mm/0.10 in. (Narrow)
Character Pitch
Font Style
Regular, Bold
Normal, Bold, Narrow
Character Width
Documents that can be scanned with the scanner
For details, refer to the Operator's Guide provided with the scanner.
Note that the paper size and weight are as follows:
Maximum size (width × length)
Document That Can
Be Scanned
304.8 mm × 431.8 mm/12.0 in. × 17.0 in.
Minimum size (width × length)
50.8 mm × 69 mm/2.00 in. × 2.72 in.
Paper weight
2
52 to 128 g/m (14 to 34 lb)
ATTENTION
Documents with glossy surface such as thermal paper, thermal transfer paper, coated
paper, and art paper take longer time for the ink to dry and may cause poor print quality.
The imprinter must be cleaned more frequently if you use these types of papers.
Thick plastic documents such as credit cards and a Carrier Sheet cannot be scanned
when the imprinter is installed.
Printing Area
D
A = 5 mm
B = 5 mm
C = 5 mm
D = 5 mm
(0.20 in.)
ATTENTION
Do not print within 5 mm from the edge of the
document.
Printing
Area
(Back)
C
A
B
±4 mm/0.16 in. from the starting point for feed direction
Accuracy of Printing
Position
21
Item
Dimension
Specification
Without scanner: 360 (W) × 435 (D) × 228 (H) (mm)/14.17 (W) × 17.13 Excluding the interface cable,
(D) × 8.98 (H) (in.)
ADF paper chute (feeder) and
With scanner: 360 (W) × 435 (D) × 264 (H) (mm)/14.17 (W) × 17.13 (D) stacker
× 10.39 (H) (in.)
4.2 kg (9.26 lb)
Weight
Temperature: 10 to 35°C (50 to 95 °F), Humidity: 20 to 80%
Ambient Condition
Consumable
Print cartridge (PART No.: CA00050-0262) (See "Contact for Purchasing Consumables or Cleaning
The printable number of characters: 4,000,000 characters (The printable number of characters differs
depending on the characters to be printed.)
Replacement cycle: 4,000,000 characters or six months after opening (A print cartridge has a specific
expiration date, and the expiration period differs whether the package is opened or
not. Start using the print cartridge before the expiration date that is written on the
package.)
22
Contact for Inquiries
Refer to the contact list on the following web page:
Image Scanner fi Series
For other inquiries regarding the scanner, refer to
the following web page:
If the solution to your problem cannot be found on
the above web page, refer to the contact
information for your Fujitsu office on the following
web page:
Contact for Purchasing Consumables or
Cleaning Materials
23
fi-760PRB Imprinter
Operator's Guide
P3PC-6112-03EN
Issue date: February 2022
Issued by: PFU Limited
The contents of this manual are subject to change without notice.
PFU Limited assumes no liability for incidental or consequential damages arising
from the use of this product, and any claims by a third party.
Copying of the contents of this manual, in whole or in part, as well as the scanner
applications is prohibited under the copyright law.
|