MAKING MODERN LIVING POSSIBLE
TS715Si
Electronic Single Channel Timeswitch
with Service Interval Timer
Danfoss Heating
Installation Guide
TS715Si
Electronic Single Channel Timeswitch
with Service Interval Timer
GB
Index
1.0 Installation Overview..............................................................................4
2.0 Product Specification..............................................................................4
3.0 Installation
3.1 Wiring.....................................................................................................5
3.2 DIL Switch Settings ...........................................................................6
4.0 Advanced Programming Options .....................................................6
5.0 Copy Functions Explained ....................................................................7
6.0 Service Interval Timer.............................................................................9
7.0 Wiring Conversions .........................................................................10-13
Danfoss Heating
3
1.0 Installation Overview
Please Note:
This product should only be installed by a qualified electrician or
competent heating installer and should be in accordance with the
current edition of the IEEE wiring regulations.
GB
2.0 Product Specification
Specification
230V model
24V model
230 Vac,
15%,
24 Vac,
15%,
Power supply
50/60 Hz
50/60 Hz
Switching action
1 x SPDT voltage free, Type 1B
24-230 Vac, 3(1)A
24 hours minimum
1 minute
Switch rating
Battery back-up
Setting/Running Accuracy
Dimensions, mm (W, H, D)
Design standard
135 x 88 x 32
EN 60730-2-7
Degree 2
Control Pollution Situation
Rated Impulse Voltage
Ball Pressure Test
2.5 kV
75°C
3.0 Installation
• Remove wallplate from unit by unscrewing the two screws on the
bottom edge of the unit.
• From the top left hand corner of the wallplate, there must be
clearances of at least 140 mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-on
module.
4
TS715SI
• The wallplate must be securely mounted either directly to the
wall using suitable wood screws or to a flush mounted 1-gang
electrical accessory box using M3.5 screws.
• Cable access can either be from behind for concealed cabling, or
from below for surface cabling. If surface cable is used, cut out
cable access slot on plug-on module prior to mounting.
GB
• For wiring connections refer to diagram below.
TS715 Si models are double insulated and do not require an
earth connection, however a parking terminal is provided on the
wallplate. This is clearly marked with an Earth symbol.
• Prior to mounting the plug-on module, DIL switches on the rear
of the plug-on module must be set. See diagram on page 6 for
available options.
• Mount plug-on module to wallplate by locating tabs on top of
wallplate in apertures on rear of module, hinge down and press
firmly to wallplate before tightening securing screws on bottom
of wallplate.
3.1 Wiring
For wiring conversion tables please see pages 10-13).
Please Note:
Link terminals L and 1 for
standard mains voltage
operated systems.
On 24 volt models power
supply must be wired to
A & B on wallplate.
COM
OFF
ON
230 V
fused 3A
Please Note:
Always switch off mains first and never fit programmer to a live
wallplate.
Danfoss Heating
5
3.2 DIL Switch Settings
Before mounting the unit, ensure the 4 DIL switches on the rear have
been moved to the required settings.
Sw.1
Sw.2
Sw.3
Sw.4
Not Used
Not Used
5/2 Day
7 Day
Not Used
GB
Not Used
7 Day or 24 Hour
24 Hour
Tick the INSTALLER SETTING box on the inside flap label to notify user
in which mode their unit is set (24hr, 5/2 day or 7 day).
INSTALLER SETTING
24 Hour
5+2 Day
7 Day
4.0 Advanced Programming Options
To enter advanced programming press PROG, + and DAY/HOL
together and hold for 5 seconds.
Option 1 - (3 or 2 On/Offs per day)
Use + or - to change between 3 or 2 on/offs each day.
2
3
3 on/offs each day (Factory setting)
2 on/offs each day
Option 2 - (Disable or enable auto time change)
Press NEXT, then use + or - to change between auto time change
enabled to auto time change disabled.
Auto time change enabled (Factory setting)
Auto time change disabled
6
TS715SI
Option 8 - (Advanced Copy Functions)
Press NEXT, then + or - to change between the following copy
options:
(0) Standard copy in 7 day and 5+2 day.
(1) Enhanced copy in 7 day, standard copy in 5+2 day.
(2) Enhanced copy in 7 day and AB copy in 5+2 day.
For an explanation of the copy features and how to use them please
see below.
GB
Press PROG to return to RUN.
5.0 Copy Functions Explained
There are 3 possible copy functions available. These are; Standard
Copy, Enhanced Copy, and AB copy. Copy functions are enabled/
disabled in the Advanced Programming Options (page 6).
Standard Copy: Pressing copy will copy the previous days events
into the displayed day. The unit will then display the 1st event for the
new day. This copy function is present only if the unit is set to run in
5+2 or 7 day mode.
Enhanced Copy: The enhanced copy function is available in 7 day
mode only. This allows any day to be copied to any other day, or days.
To use the enhanced copy function go into the event programming
using the PROG button, then:
1. Use the DAY button to find the day to be copied from.
2. Press the COPY button to select the day to be copied from. When
selected, the day should begin to flash.
3. Use the DAY button to find the day to be copied to.
4. Press COPY button to copy the selected day.
5. Repeat steps 3 and 4 to select and copy other days.
6. To stop copying, use the DAY button to go back to the flashing
day and press the COPY button. The previously flashing day will
stop flashing to indicate it has been de-selected.
NOTE: When a day has been copied to, it will remain visible and not
flashing when the DAY button is used to select other days.
Danfoss Heating
7
AB Copy: The AB copy function is available in 5+2 mode only and
only if activated in the Advanced Programming setting.
A and B days, when selected, can be any group of days e.g. 5+2,
4+3 etc. The days do not have to run in sequence. For example, to
operate in a 5+2 day mode the days can be set as follows:
GB
A Days
B Days
Mon Tues Thurs Fri Sat
Wed Sun
To use the AB copy function – press the PROG button:
1. This will show the “A”days, with all the days selected.
2. Use the DAY button to highlight a day.
3. Subsequent presses of the DAY button will increment through
the days.
4. Press the + button to select a specific day as an “A” day, or press
the – button to specify a day as a “B”day.
5. Once the day has been selected as an“A”or“B”day the programme
will automatically jump to the next day.
6. When the last day of the week is active, pressing +, -, or DAY will
move back to the “A” days displayed with no selected (flashing)
days (see image below).
7. Repeat 2 to 6 until all selections have been made.
8. When selections are completed, press the PROG button to move
to event programming.
Event Programming in AB mode
1. Programme “A” day events using the + (time advance), - (time
decrease), and NEXT (next period) buttons.
2. Press the DAY button to change to programme the “B”days.
3. Programme “B” day events using the + (time advance), - (time
decrease), and NEXT (next period) buttons.
8
TS715SI
6.0 Service Interval Timer
The TS715 Si is fitted with an installer setback service interval timer.
If this feature is required please contact our technical department.
Setting instructions for this gas safety feature are only available to
bona fide heating installers.
GB
Danfoss Heating
9
7.0 Wiring Conversions
(Applies only to 230 volt models)
Wiring conversions for other timeswitches which can be replaced
with the Danfoss TS715-Si, refer to the second part of the table. If in
any doubt, please contact our Technical Services Department before
proceeding with the replacement.
GB
MAINS
DANFOSS RANDALL
TS715-Si
N
L
L
N
The existing wallplate may be used when replacing the following, but the wiring m
link between L & COM terminals of wallplate.
ACL LS111, LS711, LP111 & LP711
DRAYTON TEMPUS ONE & TEMPUS TWO
LANDIS & GYR RWB3
N
N
N
N
L
L
L
L
LANDIS & GYR RWB30
The TS75/TS15 wallplate must be used to replace the existing wallplate when repla
mains voltage systems, fit wire link between terminal 1 & L of wallplate.
GRASSLIN 45, 45A, 45E
2
N
N
3
1
L
L
4
L
L
6
6
L
2
L
L
HONEYWELL ST6100
HORSTMANN 423 PEARL, EMERALD & TOPAZ
HORSTMANN KMK2A YMK2
HORSTMANN 425 CORONET
DANFOSS RANDALL 911
N
N
5
DANFOSS RANDALL 103, 103E, 103E5 & 103E7
RANDALL 3020
1,7
N
3
DANFOSS RANDALL SET1
RANDALL TSR2
PEGLER SUNVIC SP20 & SP25/30
POTTERTON MYSON EP4001
N
N
10
TS715SI
GB
An additional terminal block may be
required where these disconnected
leads (or pairs of leads) should be
terminated
LOAD
SPARE
COM
1
OFF
2
ON
4
3
A
B
C
D
must be reconnected as shown below. In addition, in mains voltage systems, fit wire
1
1
-
2
3
3
3
4
4
1
1
3
2
4
4
2
2
acing the following timeswitches. Wiring details are shown below. In addition, in
3
1
3
1
5
5
3
-
-
2
-
4
4
4
2
4
6
1
4
4
5
5
4
3
1
-
-
2
5
6
-
6
4
-
1
2
2
2
2
4
S
2
3
-
3
6
A
5
7
B
5
1
3
5
6
-
4
2
C
D
Danfoss Heating
11
MAINS
DANFOSS RANDALL
TS715-Si
N
L
L
N
The TS75/TS15 wallplate must be used to replace the existing wallplate when repla
mains voltage systems, fit wire link between terminal 1 & L of wallplate.
GB
SANGAMO M6
4,5
4,5
6
3
SANGAMO 410 FORM 8
SANGAMO S254 FORM 2, S408 FORM 5,
S251 FORM 2
N
L
SANGAMO S610 FORM 2, S611 FORM 2,
S612 FORM 2, S408 FORM 4, S408 FORM 6,
S253 FORM 2, S255 FORM 2
MOTOR
LIVE
N
SANGAMO S409 FORM 8
3,N
N
3,L
L
SANGAMO S263 FORM 2
SANGAMO S264 FORM 2
SMITHS IND. MKI, MKII
N
1
L
2
2
L
1
L
3
SMITHS IND. CENTROLLER 30
SMITHS IND. CENTROLLER 40
SWITCHMASTER
1
N
2
TOWERCHRON TC
VENNER VENNERETTE MKIIA
VENNER VENNERETTE MKIVA
N
2
VENNER VENOTIME
(WITH NEON INDICATING CIRCUIT ON)
N
L
VENNER VENOTIME
(WITH NEON INDICATING POWER ON)
N
3
L
2
VENNER VENNERON, VENNERON P
12
TS715SI
An additional terminal block may be
required where these disconnected
leadss (or pairs of leads) should be
terminated
LOAD
SPARE
COM
1
OFF
2
ON
4
3
A
B
C
D
acing the following timeswitches. Wiring details are shown below. In addition, in
GB
3
-
2
2
7
6
1
1
8
7
8
-
-
LOAD
SWITCH
LIVE
-
LOAD
6
-
-
1
2
OFF
ON
P2
-
-
-
-
-
-
-
P1
3
P3
4,5
4,5
1
-
6
-
4
3
2
3
8
4
3
7
9
10
11
LINE
4
LOAD
1
-
1
2
3
2
1
1
-
3
4
Danfoss Heating
13
GB
14
TS715SI
GB
Danfoss Heating
15
Danfoss Ltd.
Ampthill Road
Bedford MK42 9ER
Tel: 01234 364621
Fax: 01234 219705
Email: [email protected]
Part No. 38163v01s7-06 01/11
|