USER’S GUIDE
FAX-1840C
MFC-3240C
Version A
THIS EQUIPMENT IS DESIGNED TO WORK WITH A TWO WIRE ANALOGUE PSTN LINE
FITTED WITH THE APPROPRIATE CONNECTOR.
APPROVAL INFORMATION
Brother advises that this product may not function correctly in a
country other than where it was originally purchased, and does not
offer any warranty in the event that this product is used on public
telecommunication lines in another country.
Compilation and Publication Notice
Under the supervision of Brother Industries Ltd., this manual has
been compiled and published, covering the latest product
descriptions and specifications.
The contents of this manual and the specifications of this product are
subject to change without notice.
Brother reserves the right to make changes without notice in the
specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
i
Safety precautions
To use the machine safely
Please refer to these instructions for later reference and before
attempting any maintenance.
WARNING
There are high voltage
Do not handle the plug with wet
hands. Doing this might cause
an electrical shock.
electrodes inside the machine.
Before you clean the machine,
make sure you have
unplugged the telephone line
cord first and then the power
cord from the electrical socket.
To prevent injuries, be careful
not to touch the area shaded in
the illustration.
When you move the machine,
grasp the side handholds as
shown in the illustration.
When you move the machine,
place a hand at each side of the
unit so you are supporting the
base when you lift it. (See the
illustration on the right.)
ii
■ Use caution when installing or modifying telephone lines. Never
touch telephone wires or terminals that are not insulated unless
the telephone line has been disconnected at the wall socket.
Never install telephone wiring during a lightning storm. Never
install a telephone wall socket in a wet location.
■ This product must be installed near an electrical socket that is
easily accessible. In case of emergencies, you must disconnect
the power cord from the electrical socket in order to shut off
power completely.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the
following:
1. Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink or washing machine, in a
wet basement or near a swimming pool.
2. Avoid using this product during an electrical storm. There
may be a remote risk of electric shock from lightning.
3. Do not use this product to report a gas leak in the vicinity
of the leak.
SAVE THESE INSTRUCTIONS
iii
Choosing a location
Place your machine on a flat, stable surface that is free of vibration
and shocks, such as a desk. Put the machine near a telephone
socket and a standard, grounded electrical socket. Choose a
location where the temperature remains between 10°-35°C.
Caution
■ Avoid placing your machine in a high-traffic area.
■ Avoid placing your machine on the carpet.
■ Do not place near heaters, air conditioners, water, chemicals, or
refrigerators.
■ Do not expose the machine to direct sunlight, excessive heat,
moisture, or dust.
■ Do not connect your machine to electrical sockets controlled by
wall switches or automatic timers.
■ Disruption of power can wipe out information in the machine’s
memory.
■ Do not connect your machine to electrical sockets on the same
circuit as large appliances or other equipment that might disrupt
the power supply.
■ Avoid interference sources, such as speakers or the base units
of cordless phones.
iv
Quick Reference Guide
Storing Speed-Dial numbers
Sending faxes
1
2
Press Menu/Set, 2, 3, 2.
Using the dial pad, enter a
two-digit Speed-Dial
location number, and then
press Menu/Set.
Enter a number (up to 20
digits), and then press
Menu/Set.
Enter a name up to 15
characters (or leave it
blank), and then press
Menu/Set.
Automatic Transmission
1
If it is not illuminated in
green, press
(Fax).
2
3
Load your document.
Enter the fax number using
One-Touch, Speed-Dial,
Search or the dial pad.
3
4
4
Press Mono Start or
Colour Start.
Storing numbers
Storing One-Touch Dial
numbers
5
Press Stop/Exit.
1
2
Press Menu/Set, 2, 3, 1.
Press the One-Touch key
where you want to store the
number.
To access a One-Touch
number that is shown in a
black square on the control
panel, hold down Shift as
you press the One-Touch
key.
3
4
Enter a number (up to 20
digits), and then press
Menu/Set.
Enter a name up to 15
characters (or leave it
blank), and then press
Menu/Set.
5
Press Stop/Exit.
v
Using Search
Dialling operations
One-Touch Dialling/
Speed-Dialling
1
If it is not illuminated in
green, press (Fax).
1
If it is not illuminated in
2
3
Load your document.
green, press
(Fax).
Press Search/Speed
Dial, and then enter the first
letter of the name you’re
looking for.
2
3
Load your document.
Press the One-Touch key of
the number you want to call.
4
5
Press
memory.
or to search the
To dial a One-Touch
number that is shown in a
black square on the control
panel, hold down Shift as
you press the One-Touch
key.
Press Mono Start or
Colour Start.
Making copies
1
Press
illuminate it in green.
(Copy) to
—OR—
Press Search/Speed
Dial, press #, and then
press the two-digit
2
3
Load your document.
Press Mono Start or
Colour Start.
Speed-Dial number.
4
Press Mono Start or
Colour Start.
vi
Table of Contents
Setting Tone or Pulse dialling mode
vii
Delayed Batch Transmission
Setup for Polled Transmit (Standard)
Setup for Polled Transmit with Secure Code
viii
Printing a reduced incoming fax
Reception into memory
(Not available for colour faxes) ........................................... 6-1
ix
Using the temporary Copy keys
®
International ENERGY STAR
x
Document is jammed inside the front of the
What is the Advantage of using Telstra®
The Caller ID Appears on the Display When Your
xi
How Will the Fax Machine Treat All Other
What is the Advantage of Using the FaxAbility
The Caller ID Appears on the Display When Your
Distinctive Ringing
Connecting an external telephone answering device
Recording outgoing message (OGM) on an
Multi-line connections (PBX)
If you are installing the machine to work with a
xii
Optional External Wireless Print/Scan Server
13
xiii
Introduction
1
Using this Guide
Thank you for buying a Brother fax machine or Multi-Function Center
(MFC). Your machine is simple to use, with LCD screen instructions
to guide you through programming it. You can make the most of your
machine by reading through this Guide.
Finding information
All the chapter headings and subheadings are listed in the Table of
Contents. You will be able to find information about a specific feature
or operation by checking the Index at the back of this Guide.
Symbols used in this Guide
Throughout this Guide you will see special symbols alerting you to
important warnings, notes and actions. To make things clearer and
to help you press the correct keys, we used special fonts and added
some of the messages that will appear in the LCD.
Bold
Bold typeface identifies specific keys on the
machine control panel.
Italics
Italicized typeface emphasizes an important point
or refers you to a related topic.
Courier New Courier New type face identifies the messages on
the LCD of the machine.
Warnings inform you what to do to avoid possible personal
injury.
Cautions specify procedures you must follow or avoid to
prevent possible damage to the machine.
Notes tell you how you should respond to a situation that may
arise or give tips about how the current operation works with
other features.
Improper Setup alerts you to devices and operations that are not
compatible with the machine.
INTRODUCTION 1 - 1
One-Touch keys
Fax and telephone keys
Hook (MFC-3240C only)
Press before dialling if you want to
make sure a fax machine will
answer, and then press Mono Start
or Colour Start.
1
4
These keys give you instant access
to previously stored Quick-Dial
numbers.
Shift
To access a One-Touch number in
a black square on the control panel,
hold down this key as you press the
One-Touch key.
Hook/Hold/Recall
(FAX-1840C only)
Use to swap the line between
handset and monitor speaker.
Ink Management
(MFC-3240C only)
Lets you clean the print head, check
the print quality, and check the
available ink volume.
2
—OR—
Lets you place calls on hold.
—OR—
Also, use this key pressing with
Shift key to gain access to an
outside line and/or to recall the
operator or transfer a call to another
extension when it is connected to a
PABX.
Ink Management/Reports
(FAX-1840C only)
Lets you clean the print head, check
the print quality, and check the
available ink volume.
—OR—
Redial/Pause
Lets you accessthe Reports menuif
pressed while holding it down with
the Shift key.
Redials the last number you called.
It also inserts a pause in quick-dial
numbers.
Copy keys
3
Fax Resolution
Options
You can quickly and easily select
temporary settings for copying.
Adjusts the resolution when you
send a fax.
Mode keys:
5
Quality
Fax
Use this key for temporary copy
settings.
Lets you access Fax mode.
Scan
(MFC-3240C only)
Lets you access Scan mode.
Copy
Lets you access Copy mode.
INTRODUCTION 1 - 3
Colour Start
Liquid Crystal Display (LCD)
6
7
0
A
Displays messageson the screen to
help you set up and use your
machine.
Lets you start sending faxes or
make copies in full colour.
Also for MFC-3240C, letsyoustart a
scanning operation (in colour or
mono, depending on the scanning
setting on your PC).
Dial Pad
Use these keys to dial telephone
and fax numbers and as a keyboard
for entering information into the
machine.
Mono Start
Lets you start sending faxes or
make copies in black and white.
The # key lets you temporarily
switch the dialling mode during a
telephone call from Pulse to Tone.
(Not available in New Zealand)
Also for MFC-3240C, letsyoustart a
scanning operation (in colour or
mono, depending on the scanning
setting on your PC).
Navigation keys:
8
Menu/Set
B
Stop/Exit
The same key is used for Menu and
Set operations. Lets you access the
Menu to program and store your
settings in the machine.
Stops an operation or exits from the
menu.
You can press these keys to adjust
the volume.
▲ Search/Speed Dial
Lets you look up numbers that are
stored in the dialling memory. It also
lets you dial stored numbers by
pressing # and a two-digit number.
Press to scroll backward to a menu
selection.
▲ or ▼
Press to scroll through the menus
and options.
Power Save
9
You can turn the machine to power
save condition.
1 - 4 INTRODUCTION
Turning the machine to Power Save condition
When the machine is idle, you can turn it to Power Save condition by
pressing the Power Save key. In Power Save mode, the machine will
receive telephone calls as normal. For further information on
receiving faxes in the power save condition, please see the table on
delayed faxes that have been set up will be sent. You can even
retrieve faxes using Remote Retrieval if you are away from your
machine. If you want to do other operations, you must turn the
machine back on.
Turning the machine to Power Save condition
Press and hold down the Power Save
key until the LCD shows:
Shutting Down
The LCD light will go off.
Turning the machine to Power Save condition off
Press and hold down the Power Save
key until the LCD shows:
Please Wait
The LCD will show the date and time (Fax mode).
Even if you have turned the machine off, it will periodically clean
the print head to preserve print quality.
If you unplug the AC power cord, no machine operations will be
available.
You can turn the machine Off by customizing the Power Save
key as shown next page. In this Off mode, no machine operation
The external telephone is always available.
INTRODUCTION 1 - 5
Power Save Setting
You can customise the machine’s Power Save key. The default
mode is Fax Receive:On, so your machine can receive faxes or
calls even when the machine is in Power Save mode. If you do not
want your machine to receive faxes or calls, turn this setting to
1
2
3
4
Press Menu/Set, 1, 6.
Press ▲ or ▼ to select Off(or On).
Press Menu/Set.
6.P.Save Setting
Press Stop/Exit.
On/Off Setting
Receive Mode Available Operations
Fax Receive:On Fax Only
Fax Receive (automatically), Fax
Detect, Delayed Fax*1, Remote Fax
Options*1, Remote Retrieval*1:
(default)
External TAD
■
(FAX-1840C only) You can receive
telephone calls by lifting the
handset.
Manual
Fax/Tel*2
Delayed Fax*1, Fax Detect:
■
(FAX-1840C only) You can receive
telephone calls by lifting the
handset.
Fax Receive:Off
—
No machine operations will be
available.
*1 Should be set before you switch off the machine.
*2 You can not receive a fax automatically even if you have set the receive mode to
Fax/Tel. (MFC-3240C only)
1 - 6 INTRODUCTION
Load documents
You can send a fax, make copies, and scan from the ADF (automatic
document feeder).
Using the automatic document feeder (ADF)
The ADF can hold up to 20 pages and feeds each sheet individually.
Use standard 80 gsm paper and always fan the pages before putting
them in the ADF.
Recommended environment
Temperature:
Humidity:
Paper:
20° - 30° C
50% - 70%
80 gsm A4
DO NOT use paper that is curled, wrinkled, folded, ripped,
stapled, paper clipped, pasted or taped.
DO NOT use cardboard, newspaper or fabric.
■ Make sure documents written with ink are completely dry.
■ Documents to be faxed must be from 8.9 to 21.6 cm wide and 12.7
to 35.6 cm long.
INTRODUCTION 1 - 7
1
2
Fan the pages well and stagger them at an angle.
Open the document tray (1) and pull out the extension (2) and
then open the document support (3).
3
4
Put the documents face down, top edge first in the ADF until
you feel them touch the feed roller (4).
Adjust the paper guides to fit the width of your documents (5).
Documents are
Face Down in the ADF.
Paper
Guides
DO NOT pull on the document while it is feeding.
1 - 8 INTRODUCTION
About paper
The print quality can be affected by the type of paper you use in the
machine.
To get the best print quality for the settings you’ve chosen, always
set the Paper Type to match the type of paper you load.
You can use plain paper, inkjet paper (coated paper), glossy paper,
transparencies and envelopes.
We recommend testing various paper types before purchasing large
quantities.
For best results, use the recommended paper.
■ When you print on inkjet paper (coated paper),
transparencies and glossy paper, be sure to select the
proper media in the “Basic” tab of the printer driver or in the
Paper Type setting of the menu (Menu/Set, 1, 2).
■ When you print on Brother glossy paper, load the instruction
sheet included with the glossy paper in the paper tray first,
and then place the glossy paper on the instruction sheet.
■ When you use transparencies or glossy paper, remove each
sheet immediately to prevent smudging or paper jams.
■ Avoid touching the printed surface of the paper immediately
after printing; the surface may not be completely dry and
may stain your fingers.
Recommended Paper
To get the best print quality, we suggest using Brother paper.
(See table below.)
If Brother paper is not available in your country, we recommend
testing various papers before purchasing large quantities.
We recommend using “3M Transparency Film” when you print on
transparencies.
Brother Paper
Paper Type
A4 Plain
Item
BP60PA
BP60GLA
BP60MA
A4 Glossy
A4 Inkjet (Photo Matte)
INTRODUCTION 1 - 9
Handling and using special paper
■ Store paper in its original packaging, and keep it sealed. Keep the
paper flat and away from moisture, direct sunlight and heat.
■ The coated side of glossy paper is shiny. Avoid touching the
shiny (coated) side. Load glossy paper with the shiny side facing
down.
■ Avoid touching either side of transparencies, because they
absorb water and perspiration easily, and this may cause
decreased output quality. Transparencies designed for laser
printers/copiers may stain your next document. Use only
transparencies recommended for inkjet printing.
Do not use paper:
■ that are damaged, curled, wrinkled, or irregularly shaped
2 mm or
longer
2 mm or
longer
■ that are extremely shiny or highly textured
■ that were previously printed by a printer
■ that cannot be arranged uniformly when stacked
■ that are made with a short grain
1 - 10 INTRODUCTION
Paper type and size for each operation
Paper Type
Paper Size
Usage
Fax
Copy
Printer
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Cut Paper
Letter
216 x 279 mm (8 1/2" x 11")
210 x 297 mm (8.3" x 11.7")
216 x 356 mm (8 1/2" x 14")
184 x 267 mm (7 1/4" x 10 1/2")
182 x 257 mm (7.2" x 10.1")
148 x 210 mm (5.8" x 8.3")
105 x 148 mm (4.1" x 5.8")
102 x 152 mm (4" x 6")
Yes
Yes
A4
Yes
Yes
Legal
Yes
Yes
Executive
JIS B5
A5
-
-
-
-
-
-
-
-
-
-
-
-
Yes
A6
-
Cards
Photo
Yes
Photo L
Photo 2L
Index Card
Post Card 1
89 x 127 mm (3 1/2" x 5")
127 x 178 mm (5" x 7")
-
-
-
-
-
127 x 203 mm (5" x 8")
100 x 148 mm (3.9" x 5.8")
148 x 200 mm (5.8" x 7.9")
Post Card 2
(Double)
Envelopes
C5 Envelope
DL Envelope
COM-10
Monarch
JE4 Envelope
Letter
162 x 229 mm (6.4" x 9")
-
-
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
110 x 220 mm (4.3" x 8.7")
105 x 241 mm (4 1/8" x 9 1/2")
98 x 191 mm (3 7/8" x 7 1/2")
105 x 235 mm (4.1" x 9.3")
216 x 279 mm (8 1/2" x 11")
210 x 297 mm (8.3" x 11.7")
-
-
-
-
Transparencies
Yes
Yes
A4
Paper weight, thickness and capacity
Paper Type
Weight
Thickness
No. of sheets
Cut Paper
Plain Paper
Inkjet Paper
Glossy Paper
Photo Card
Index Card
Post Card
64 to 120 gsm
(17 to 32 lb)
0.08 to 0.15 mm
(0.003" to 0.006")
100*
64 to 200 gsm
(17 to 53 lb)
0.08 to 0.25 mm
(0.003" to 0.01")
20
20
20
30
30
10
10
Up to 220 gsm
(Up to 58 lb)
Up to 0.25 mm
(Up to 0.01")
Cards
Up to 240 gsm
(Up to 64 lb)
Up to 0.28 mm
(Up to 0.01")
Up to 120 gsm
(Up to 32 lb)
Up to 0.15 mm
(Up to 0.006")
Up to 200 gsm
(Up to 53 lb)
Up to 0.23 mm
(Up to 0.01")
Envelopes
75 to 95 gsm
(20 to 25 lb)
Up to 0.52 mm
(Up to 0.02")
Transparencies
-
-
* Up to 50 sheets for Legal size paper (80 gsm).
* Up to 100 sheets of 80 gsm.
Paper capacity of the output paper tray
Output Paper
Tray
Up to 50 sheets of 80 gsm (A4)
■ Transparencies or glossy paper must be
picked up from the output paper tray one
page at a time to avoid smudging.
■ Legal paper cannot be stacked on the output
paper tray.
1 - 12 INTRODUCTION
Printable area
The printable area depends on the settings in the application you are
using. The figures below show the unprintable areas on cut sheet
paper and envelopes.
Cut Sheet Paper
Envelopes
3
4
3
4
1
1
2
■ unprintable area
2
1Top
2Bottom
3Left
4Right
Cut Sheet
Envelopes
3 mm
3 mm
3 mm
3 mm
(0 mm)*1
(0 mm)*1
(0 mm)*1
(0 mm)*1
12 mm
24 mm
3 mm
3 mm
*1 When you set the Borderless feature to On.
Printable area depends on the Printer driver settings.
The figures above are approximate and the printable area may
vary depending on the type of cut sheet paper you are using.
INTRODUCTION 1 - 13
How to load paper, envelopes and post cards
To load paper or other media
1
Pull the paper tray completely out of the machine and remove
the output paper tray.
2
Press and slide the paper side guide to fit the paper width.
Paper Side Guide
3
Pull out the paper support and unfold the paper support flap.
Paper Support
Paper Support Flap
Use the paper support flap for Letter, Legal and A4.
1 - 14 INTRODUCTION
4
5
Fan the stack of paper well to avoid paper jams and mis-feeds.
Gently insert the paper into the paper tray print side down and
the leading edge (top of the paper) in first.
Check that the paper is flat in the tray and below the maximum
paper mark.
Maximum Paper Mark
■ Make sure the paper side guides touch the sides of the
paper.
■ Be careful that you do not push the paper in too far; it may
lift at the back of the tray and cause feed problems.
6
Put the output paper tray back on and push the paper tray firmly
back into the machine.
INTRODUCTION 1 - 15
To load envelopes
■ Use envelopes that weigh from 75-95 gsm.
■ Some envelopes require margin settings in the application. Make
sure you do a test print first.
To prevent possible damage to the feeding mechanism, do not
use the types of envelopes shown below.
DO NOT USE ENVELOPES:
■ that are of a baggy construction
■ that are embossed (have raised writing on them)
■ that have clasps on them
■ that are not sharply creased
■ that are preprinted on the inside
■ Glue
■ Rounded
■ Double flap ■ Triangular
flap
flap
How to load envelopes
1
Before loading, press the corners and sides of the envelopes to
make them as flat as possible.
If the envelopes are ‘double-feeding,’ put one envelope in the
paper tray at a time.
1 - 16 INTRODUCTION
2
Insert the envelopes into the paper tray with the address side
down and the leading edge (top of the envelopes) in first. Slide
the paper side guide to fit the width of the envelopes.
If you have problems when printing on envelopes, try the
following suggestions:
1
2
Open the envelope flap.
Make sure the open flap is either to the side of the envelope or
to the back edge of the envelope when printing.
3
Adjust the size and margin in your application.
To load post cards
1
Raise the paper stop and insert the post cards into the paper
tray. Slide the paper side guide to fit the width of the post cards.
INTRODUCTION 1 - 17
About fax machines
Fax tones and handshake
When someone is sending a fax, the machine sends fax calling tones
(CNG tones). These are quiet, intermittent beeps every 4-seconds.
You’ll hear them after you dial and press Mono Start or
Colour Start and they will continue for about 60 seconds after
dialling. During that time, the sending machine must begin the
“handshake”, or connection, with the receiving machine.
Each time you use automatic procedures to send a fax, you are
sending CNG tones over the phone line. You will soon learn to listen
for these quiet beeps each time you answer a phone on your fax line,
so you will know if you are receiving a fax message.
The receiving fax responds with fax receiving tones, which are loud,
chirping sounds. A receiving fax chirps for about 40 seconds over the
phone line, and the LCD shows Receiving.
If your machine is set to the Fax Only mode, it will answer every call
automatically with fax receiving tones. If the other person hangs up,
your machine will continue to send the “chirps” for about 40 seconds,
and the LCD continues to show Receiving. To cancel receiving,
press Stop/Exit.
The fax ‘handshake’ is the time in which the sending machine’s CNG
tones and the receiving machine’s “chirps” overlap. This must be for
at least 2 to 4 seconds, so both machines can understand how each
is sending and receiving the fax. The handshake cannot begin until
the call is answered, and the CNG tones only last for about 60
seconds after the number is dialled. So it is important for the
receiving machine to answer the call in as few rings as possible.
When you have an external Telephone Answering Device (TAD)
on your fax line, your TAD will decide the number of rings before
the call is answered.
1 - 18 INTRODUCTION
ECM (Error Correction Mode)
The Error Correction Mode (ECM) is a way for the machine to check
a fax transmission while it is in progress. If the machine detects
errors during fax transmission, it resends the pages of the fax that
had an error. ECM transmissions are only possible between fax
machines that both have this feature. If they do, you may send and
receive fax messages that are continuously being checked by the
machine.Your machine must have enough memory for this feature to
work.
INTRODUCTION 1 - 19
Getting started
2
Initial Setup
Setting the Date and Time
When the machine is not in use it will display the date and time. If you
set up the Station ID the date and time displayed by your machine
will be printed on every fax you send. If there is a power failure, you
may have to reset the date and time. No other settings will be
affected.
1
2
Press Menu/Set, 0, 2.
Enter the last two digits of the year.
Press Menu/Set.
2.Date/Time
3
Enter two digits for the month.
Press Menu/Set.
(For example, enter 09 for September, or 10 for October.)
Enter two digits for the day.
4
5
6
Press Menu/Set. (For example, enter 06 for 6th.)
Enter the time in 24-Hour format.
Press Menu/Set. (For example, enter 15:25 for 3:25 P.M.)
Press Stop/Exit.
The LCD now shows the date and time whenever the machine
is in Fax mode.
Setting Tone or Pulse dialling mode
(Not available in New Zealand)
1
2
Press Menu/Set, 0, 4.
Press ▲ or ▼ to select Pulse(or
Tone).
4.Tone/Pulse
Press Menu/Set.
3
Press Stop/Exit.
2 - 1 GETTING STARTED
Setting the Station ID
You should store your name or company name and fax number so
they print on all fax pages you send.
It is important that you enter the fax number in the internationally
standardised format, i.e. in accordance with the following strict
sequence:
■ The “+” (plus) character (by pressing
key)
■ Your Country Code (e.g. “61” for Australia, “64” for New Zealand)
■ Your local area code minus any leading “0”
■ A space
■ Your number on the local exchange, using spaces to aid
readability as appropriate.
As an example, if the machine is installed in the United Kingdom and
the same line is to be used for both fax and voice calls, and your
national telephone number is 0161 444 5555, then you must set the
fax and telephone number parts of your station ID as:
+44 161 444 5555.
1
2
Press Menu/Set, 0, 3.
Enter your fax number
(up to 20 digits).
3.Station ID
Press Menu/Set.
You cannot enter a hyphen. To enter a space press
between numbers.
once
3
4
Use the dial pad to enter your name (up to 20 characters).
Press Menu/Set.
Press Stop/Exit.
If the Station ID has already been programmed, the LCD will ask
you to press 1 to make a change or 2 to exit without changing.
GETTING STARTED 2 - 2
Setting the Phone Line Type
If you are connecting the machine to a line that features a PABX
(PBX) or ADSL to send and receive faxes, it is also necessary to
change the Phone Line Type accordingly by completing the following
steps.
1
2
Press Menu/Set, 0, 5.
Press ▲ or ▼ to select PBX(For
Australia and New Zealand only), ADSL, ISDN(or Normal).
5.Phone Line Set
Press Menu/Set.
3
Press Stop/Exit.
PABX and TRANSFER
The machine is initially set to be connected with PSTN (Public
Switched Telephone Network) lines. However, many offices use a
central telephone system or Private Automatic Branch Exchange
(PABX). Your machine can be connected to most types of PABX.
The machine’s recall feature supports timed break recall only (TBR).
TBR will work with most PABX systems allowing you to gain access
to an outside line, or transfer calls to another extension. The feature
works when the Hook key is pressed.
■ You can program a Hook keypress as part of a number
stored in a One-Touch or Speed-Dial location. When
programming the One-Touch or Speed-Dial number
(Menu/Set 2-3-1 or 2-3-2) press Hook first (the screen
displays "!"), then enter the telephone number. If you do this,
you do not need to press Hook each time before you dial
■ For FAX-1840C, press Hook/Hold/Recall key while
holding down the Shift key.
2 - 3 GETTING STARTED
General Setup
Setting the Mode Timer (MFC-3240C only)
The machine has three temporary mode keys on the control panel:
Fax, Scan and Copy. You can change the number of seconds or
minutes the machine takes after the last Scan or Copy operation
before it returns to Fax mode. If you select Off, the machine stays
in the mode you used last.
1
2
Press Menu/Set, 1, 1.
Press ▲ or ▼ to select 0Sec,
30Secs, 1Min, 2Mins, 5Minsor Off.
1.Mode Timer
Press Menu/Set.
3
Press Stop/Exit.
GETTING STARTED 2 - 4
Setting the Mode Timer (FAX-1840C only)
The machine has two temporary mode keys on the control panel: Fax
and Copy. You can change the number of seconds or minutes the
machine takes after the last Copy operation before it returns to Fax
mode. If you select Off, the machine stays in the mode you used
last.
1
2
Press Menu/Set, 1, 1.
Press ▲ or ▼ to select 0Sec,
30Secs, 1Min, 2Mins, 5Minsor Off.
1.Mode Timer
3
4
Press Menu/Set.
Press Stop/Exit.
2 - 5 GETTING STARTED
Setting the Paper Type
To get the best print quality, set the machine for the type of paper you
are using.
1
2
Press Menu/Set, 1, 2.
Press ▲ or ▼ to select Plain,
Inkjet, Glossyor Transprncy.
2.Paper Type
Press Menu/Set.
3
Press Stop/Exit.
The machine ejects paper with printed surfaces face up onto the
paper tray in the front of the machine. When you use
transparencies or glossy paper, remove each sheet immediately
to prevent smudging or paper jams.
Setting the Paper Size
You can use five sizes of paper for printing copies: Letter, Legal, A4,
A5, and 10 x 15 cm and three sizes for printing faxes: Letter, Legal
and A4. When you change the type of paper you load in the machine,
you will need to change the setting for Paper Size at the same time
so your machine can fit an incoming fax on the page.
1
2
Press Menu/Set, 1, 3.
Press ▲ or ▼ to select Letter,
Legal, A4, A5or 10x15cm.
3.Paper Size
Press Menu/Set.
3
Press Stop/Exit.
GETTING STARTED 2 - 6
Setting the Ring Volume
You can turn the ring Ring Volume:Offor you can select the ring
volume level.
1
2
Press Menu/Set, 1, 4, 1.
Press ▲ or ▼ to select Low, Med,
Highor Off.
1.Ring
Press Menu/Set.
3
Press Stop/Exit.
—OR—
You can adjust the ring volume when your machine is idle (not being
used). In Fax mode , press or to adjust the volume
level. Every time you press these keys, the machine will ring so you
can hear the active setting as the LCD shows it. The volume changes
with each key press. The new setting will stay until you change it
again.
Setting the Beeper Volume
You can change the beeper volume. The default (factory) setting is
Beeper:Low. When the beeper is on, the machine will beep when
you press a key, make a mistake or after you send or receive a fax.
1
2
Press Menu/Set, 1, 4, 2.
Press ▲ or ▼ to select your option.
(Low, Med, Highor Off)
2.Beeper
Press Menu/Set.
3
Press Stop/Exit.
2 - 7 GETTING STARTED
Setting the Speaker Volume
You can select the speaker volume.
1
2
Press Menu/Set, 1, 4, 3.
Press ▲ or ▼ to select Low, Med,
Highor Off.
3.Speaker
Press Menu/Set.
3
Press Stop/Exit.
Turning on Automatic Daylight Savings Time
You can set the machine to change automatically for Daylight
Savings Time. It will reset itself forward one hour in the Spring and
backward one hour in the Autumn. Make sure you have set the
correct day and time in the Date/Timesetting.
1
2
Press Menu/Set, 1, 5.
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
5.Auto Daylight
3
Press Stop/Exit.
Setting the LCD Contrast
You can adjust the LCD contrast for a sharper and more vivid
display. If you are having difficulty reading the LCD from your
position, try changing the contrast setting for improved viewing.
1
2
Press Menu/Set, 1, 7.
Press ▲ or ▼ to select Lightor
Dark.
7.LCD Contrast
Press Menu/Set.
3
Press Stop/Exit.
GETTING STARTED 2 - 8
Setup Send
3
How to enter Fax mode
Before sending faxes, make sure
(Fax) is illuminated in
green. If not, press
setting is Fax.
(Fax) to enter Fax mode. The default
How to dial
You can dial in any of the following ways.
Manual dialling
Press all of the digits of the phone or fax number.
3 - 1 SETUP SEND
One-Touch dialling
Press the One-Touch Key of the location you want to call.
To dial One-Touch numbers in the black square, hold down Shift as
you press the One-Touch Key.
Speed-Dialling
Press Search/Speed Dial, #, and then the two digit Speed-Dial
two-digit number
If the LCD shows Not Registeredwhen you enter the
Speed-Dial number, a number has not been stored for it.
SETUP SEND 3 - 2
Search
You can search for names you have stored in the One-Touch and
Speed-Dial memories. Press Search/Speed Dial and the
To search numerically
or
To search alphabetically*
* To search alphabetically, you can use the dial pad to enter the first
letter of the name you are looking for.
Fax Redial
If you are sending a fax manually and the line is busy, press
Redial/Pause, and then press Mono Start or Colour Start to try
again. If you want to make a second call to the last number dialled,
you can save time by pressing Redial/Pause and Mono Start or
Colour Start.
Redial/Pause only works if you dialled from the control panel.
If you are sending a fax automatically and the line is busy, the
machine will automatically redial up to three times at five minute
intervals.
3 - 3 SETUP SEND
How to Fax (B&W and Colour)
Colour fax transmission
Your machine can send a colour fax to machines that support this
feature.
However, colour faxes cannot be stored in the memory. When you
send a colour fax, the machine will send it in real time (even if
Real Time TXis set to Off).
Faxing from the ADF
Put the document face down in the ADF. To cancel, press
Stop/Exit.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Dial the fax number.
Press Mono Start or Colour Start.
■ The machine starts scanning the document.
If the memory is full and you are faxing a single page, it will be
sent in real time.
Automatic transmission
This is the easiest way to send a fax.
1
2
3
If it is not illuminated in green, press
Load your document.
(Fax).
3-1.)
4
Press Mono Start or Colour Start.
SETUP SEND 3 - 4
Manual transmission
Manual transmission lets you hear the dialling, ringing and
fax-receiving tones while sending a fax.
1
2
3
If it is not illuminated in green, press
Load your document.
(Fax).
Pick up the handset of the machine (FAX-1840C)/external
phone (MFC-3240C) and listen for a dial tone.
4
5
Dial the fax number you want to call.
When you hear the fax tone, press Mono Start or
Colour Start.
6
If you picked up the handset replace it.
Sending a fax at the end of a conversation
At the end of a conversation you can send a fax to the other party
before you both hang up.
1
Ask the other party to wait for fax tones (beeps) and then to
press Start or Send key before hanging up.
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Mono Start or Colour Start.
3 - 5 SETUP SEND
Basic sending operations
Sending faxes using multiple settings
When you send a fax you can choose any combination of these
settings: contrast, resolution, overseas mode, delayed fax timer,
polling transmission or real time transmission.
1
If it is not illuminated in green, press
(Fax).
After each setting is accepted, the LCD will ask if you want to
enter more settings:
2
Press 1to select more settings. The
Next
LCD will return to the Setup Send
1.Yes 2.No
menu.
—OR—
Press 2 if you have finished choosing settings and go to the next
step.
Contrast
If your document is very light or very dark, you may want to change the
contrast.
Use Lightto send a light document.
Use Darkto send a dark document.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 1.
Press ▲ or ▼ to select Auto, Light
or Dark.
1.Contrast
Press Menu/Set.
SETUP SEND 3 - 6
Fax Resolution
You can use the Fax Resolution key to change the setting
temporarily (for this fax only). In Fax mode
, press
Fax Resolution and ▲ or ▼ to select the setting you want, and then
press Menu/Set.
—OR—
You can change the default setting:
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 2.
Press ▲ or ▼ to select the resolution
you want.
2.Fax Resolution
Press Menu/Set.
Standard
Fine
Suitable for most typed documents.
Good for small print and transmits a little
slower than Standard resolution.
S.Fine
Photo
Good for small print or artwork and transmits
slower than Fine resolution.
Use when the document has varying shades
of gray or is a photograph. This has the
slowest transmission time.
3 - 7 SETUP SEND
Dual Access (Not available for colour faxes)
You can dial a number, and begin scanning the fax into memory—
even when the machine is sending from memory or receiving faxes.
The LCD shows the new job number and available memory.
Your machine normally uses Dual Access. However, to send a
colour fax, the machine will send the document in real time
(even if Real Time TXis Off).
The number of pages you can scan into the memory will vary
depending on the data that is printed on them.
If you get an Out of Memorymessage while scanning the first
page of a fax, press Stop/Exit to cancel scanning. If you get an
Out of Memorymessage while scanning a subsequent page,
you can press Mono Start to send the pages scanned so far,
or press Stop/Exit to cancel the operation.
SETUP SEND 3 - 8
Real Time Transmission
When you are sending a fax, the machine will scan the documents
into the memory before sending. Then, as soon as the phone line is
free, the machine will start dialling and sending.
If the memory becomes full, the machine will send the document in
real time (even if Real Time TXis set to Off).
Sometimes, you may want to send an important document
immediately, without waiting for memory transmission. You can set
Real Time TXto Onfor all documents or for the next fax only.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 5.
To change the default setting, press
▲ or ▼ to select On(or Off).
5.Real Time TX
Press Menu/Set.
—OR—
For the next fax transmission only, press ▲ or ▼ to select
Next Fax Only.
Press Menu/Set and go to Step 5.
For the next fax only, press ▲ or ▼ to select On(or Off).
Press Menu/Set.
5
In Real Time Transmission, the redial feature does not work.
If you are sending a colour Fax, the machine will send it in real
time (even if Real Time TXis set to Off).
3 - 9 SETUP SEND
Checking job status
Check which jobs are still waiting in the memory to be sent. (If there
are no jobs, the LCD shows No Jobs Waiting.)
1
2
Press Menu/Set, 2, 6.
If you have more than one job
waiting, press ▲ or ▼ to scroll through the list.
6.Remaining Jobs
3
Press Stop/Exit.
Cancelling a fax in progress
If you want to cancel a fax, while the machine is scanning, dialling or
sending it, press Stop/Exit.
Cancelling a scheduled job
You can cancel a fax job that is stored and waiting in the memory.
1
Press Menu/Set, 2, 6.
Any jobs that are waiting will appear
on the LCD.
6.Remaining Jobs
2
If you have more than one job waiting, press ▲ or ▼ to select the
job you want to cancel.
Press Menu/Set.
—OR—
If you only have one job waiting, go to Step 3.
Press 1 to cancel.
To cancel another job go to Step 2.
—OR—
3
4
Press 2 to exit without cancelling.
Press Stop/Exit.
SETUP SEND 3 - 10
Advanced sending operations
Broadcasting (Not available for colour faxes)
Broadcasting is when the same fax message is automatically sent to
more than one fax number. You can include Groups, One-Touch,
Speed-Dial numbers and up to 50 manually dialled numbers in the
same broadcast.
Press Menu/Set between each of the numbers. Use
Search/Speed Dial to help you choose the numbers easily. (To set
page 5-4.)
After the broadcast is finished, a Broadcast Report will be printed to
let you know the results.
1
2
3
If it is not illuminated in green, press
Load your document.
(Fax).
Enter a number using One-Touch, Speed-Dial, a Group
number, Search or manual dialling using the dial pad.
(Example: Group number)
4
5
When the LCD displays the fax number or name of the other
party, press Menu/Set.
You will be asked to enter the next number.
Enter the next number.
(Example: Speed-Dial number)
6
7
8
When the LCD displays the fax number or name of the other
party, press Menu/Set.
After you have entered all the fax numbers, go to step 8 to start
the broadcast.
Press Mono Start.
3 - 11 SETUP SEND
■ If you did not use up any of the numbers for Groups, access
codes or credit card numbers, you can ‘broadcast’ faxes to
as many as 100 different numbers.
■ The available memory will vary depending on the types of
jobs in the memory and the number of locations used for
broadcasting. If you broadcast to the maximum numbers
available, you will not be able to use Dual Access and
Delayed fax.
■ Enter the long dialling sequence numbers as you would
normally, but remember that each One-Touch and
Speed-Dial number counts as one number, so the number of
locations you can store becomes limited.
■ If the memory is full, press Stop/Exit to stop the job or if
more than one page has been scanned, press Mono Start
to send the portion that is in the memory.
Overseas Mode
If you are having difficulty sending a fax overseas due to possible
interference on the phone line, we recommend that you turn on the
Overseas Mode. After you send a fax using this feature, the feature
will turn itself off.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 7.
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
7.Overseas Mode
SETUP SEND 3 - 12
Delayed Fax (Not available for colour faxes)
During the day you can store up to 50 faxes in the memory to be sent
within 24 hours. These faxes will be sent at the time of day you enter
in Step 4.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 3.
Press Menu/Set to accept the
displayed time.
3.Delayed Fax
—OR—
Enter the time you want the fax to be sent (in 24-hour format).
Press Menu/Set.
(For example, enter 19:45 for 7:45 PM.)
5
Press 1 to leave the documents
waiting in the ADF.
1.Doc 2.Memory
—OR—
Press 2 to scan the documents into the memory.
The number of pages you can scan into the memory depends
on the amount of data that is printed on each page.
3 - 13 SETUP SEND
Delayed Batch Transmission
(Not available for colour faxes)
Before sending the delayed faxes, your machine will help you
economize by sorting all the faxes in the memory by destination and
scheduled time. All delayed faxes that are scheduled to be sent at
the same time to the same fax number will be sent as one fax to save
transmission time.
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 2, 4.
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
(Fax).
4.Batch TX
4
Press Stop/Exit.
SETUP SEND 3 - 14
Setup for Polled Transmit (Standard)
(Not available for colour faxes)
Polled Transmit is when you set up the machine to wait with a
document so another fax machine can retrieve it.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 6.
Press ▲ or ▼ to select Standard.
Press Menu/Set.
6.Polled TX
5
Press 1 to leave documents in the
ADF. The document will remain in
1.Doc 2.Memory
the ADF until the machine is polled. If you need to use your
machine before the polled transmit occurs, you must first cancel
this job.
—OR—
Press 2 to scan the document into memory. The document will
be stored and can be retrieved from any other fax machine until
you delete the fax in memory by using the Cancelling a Job
menu setting.
3 - 15 SETUP SEND
Setup for Polled Transmit with Secure Code
(Not available for colour faxes)
When you choose Polling:Secure, anyone who polls the
machine must enter the polling secure code.
1
2
3
4
If it is not illuminated in green, press
Load your document.
(Fax).
Press Menu/Set, 2, 2, 6.
Press ▲ or ▼ to select Secure.
Press Menu/Set.
6.Polled TX
5
6
Enter a four-digit number.
Press Menu/Set.
Press 1 to leave documents in the
ADF. The document will remain in
1.Doc 2.Memory
the ADF until the machine is polled. If you need to use your
machine before the polled transmission occurs, you must first
cancel this job.
—OR—
Press 2 to scan the document into memory. The document will
be stored and can be retrieved from any other fax machine until
you delete the fax in memory by using the Cancelling a Job
You can use Secure Polling only with another Brother fax
machine.
SETUP SEND 3 - 16
TX Lock (Key Lock for some countries)
TX Lock lets you prevent unauthorized access to the machine.
While TX Lock is Onthe following operations are available:
■ Receiving faxes
■ Fax Forwarding (If Fax Forwarding was already On)
■ Remote Retrieval (If Fax Storage was already On)
While TX Lock is Onthe following operations are NOT available:
■ Sending faxes
■ Copy
■ PC printing (MFC-3240C only)
■ PC scanning (MFC-3240C only)
You will not be able to continue to schedule Delayed Faxes or
Polling jobs. However, any pre-scheduled Delayed Faxes will be
sent when you turn TX Lock On, so they won't be lost.
If you have selected Fax Forwarding or Fax Storage
(Menu/Set, 2, 5) before you turn TX Lock On, then Fax
Forwarding and Remote Retrieval will continue to work.
To print the faxes in memory, turn TX Lock Off.
3 - 17 SETUP SEND
Setting up the password
If you forget the TX Lock password, please contact your Brother
dealer or Brother for assistance.
1
2
Press Menu/Set, 2, 0, 1.
Enter a 4-digit number for the
password.
1.TX Lock
Press Menu/Set.
3
If the LCD shows Verify:, re-enter the password.
Press Menu/Set.
Changing the TX Lock password
1
2
Press Menu/Set, 2, 0, 1.
Press ▲ or ▼ to select Set
Password.
1.TX Lock
Press Menu/Set.
3
4
5
Enter a 4-digit number for the current password.
Press Menu/Set.
Enter a 4-digit number for a new password.
Press Menu/Set.
If the LCD shows Verify:, re-enter the password.
Press Menu/Set.
SETUP SEND 3 - 18
Turning TX Lock on
1
2
Press Menu/Set, 2, 0, 1.
Press ▲ or ▼ to select Set TX
Lock.
1.TX Lock
Press Menu/Set.
3
Enter the registered 4-digit password.
Press Menu/Set.
The machine goes offline and the LCD shows TX Lock Mode.
Turning TX Lock off
1
2
Press Menu/Set.
Enter the registered 4-digit password.
Press Menu/Set.
TX lock is automatically turned off.
If you enter the wrong Password, the LCD shows Wrong
Passwordand stays offline. The machine will stay in TX Lock
Mode until the registered password is entered.
3 - 19 SETUP SEND
Setup Receive
4
Basic receiving operations
Choosing the Receive Mode
There are four different Receive Modes for your machine. You can
choose the mode that best suits your needs.
LCD
How it works
When to use it
Fax Only
The machine
For dedicated fax lines.
automatically answers
every call as a fax.
(automatic receive)
Fax/Tel
The machine controlsthe Use this mode if you expect to receive lots of fax
line and automatically messages and few telephone calls. You cannot
(fax and telephone)
answers every call. If the have an answering machine on the same line, even
call is a fax it will receive if it is on a separate wall socket/phone socket on
the fax. If the call is not a the same line. You cannot use the telephone
(with an external or
extension telephone
for models without a
handset)
fax it will ring
company’s Voice Mail in this mode.
(pseudo/double ring) for
you to pick up the call.
External TAD
The external answering
machine (TAD)
automatically answers
every call.
Voice messages are
stored on the external
TAD. Fax messages are
printed.
Use this mode if you have connected an answering
machine to your machine.
The External TAD setting works only with an
external answering machine. Ring Delay does not
work in this setting.
(with an external
answering machine
only)
Manual
You control the phone
line and must answer
every call yourself.
Use this mode if you do not receive many fax
messages.
If you answer and hear fax tones, wait until the MFC
(manual receive)
(with an external or
extension telephone
for models without a
handset)
Note: If you use a computer modem on the same
line MFC Faxing will not operate correctly.
SETUP RECEIVE 4 - 1
To select or change your Receive Mode
1
2
Press Menu/Set, 0, 1.
Press ▲ or ▼ to select Fax Only,
Fax/Tel, External TADor Manual.
1.Receive Mode
Press Menu/Set.
3
Press Stop/Exit.
Current Receive Mode
Fax: Fax Only
F/T: Fax/Tel
TAD: External TAD
Mnl: Manual
Setting the Ring Delay
The Ring Delay sets the number of times the machine rings before it
answers in Fax Onlyor Fax/Telmode. If you have extension
phones on the same line as the machine, keep the Ring Delay setting
of 6.
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 1.
Press ▲ or ▼ to select how many
times the line rings before the machine answers (02 - 10 for
Australia, 01 - 10 for New Zealand, 00 - 10 for some countries).
(Fax).
1.Ring Delay
Press Menu/Set.
(If you select 00, the line won’t ring at all.)
4
Press Stop/Exit.
4 - 2 SETUP RECEIVE
Setting the F/T Ring Time (Fax/Tel mode only)
If you set the Receive Mode to Fax/Tel, you’ll need to decide how long
the machine will signal you with its special pseudo/double-ring when
you have a voice call. (If it’s a fax call, the machine prints the fax.)
This pseudo/double-ring happens after the initial ringing from the
phone company. Only the machine rings and no other phones on the
same line will ring with the special pseudo/double-ring. However, you
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 2.
Press ▲ or ▼ to select how long the
(Fax).
2.F/T Ring Time
machine will ring to alert you that you have a voice call (20, 30,
40 or 55 seconds for New Zealand and China).
Press Menu/Set.
4
Press Stop/Exit.
Even if the caller hangs up during the pseudo/double-ringing,
the machine will continue to ring for the set time.
SETUP RECEIVE 4 - 3
Fax Detect (MFC-3240C only)
When you use this feature, you don’t have to press Mono Start,
Colour Start, or the Fax Receive Code 51 ( 91 for New
Zealand) when you answer a fax call. Selecting Fax Detect:On
allows the machine to receive fax calls automatically, even if you lift
the handset of an extension or external phone. When you see
Receivingon the LCD or when you hear ‘chirps’ through the
handset of an extension phone connected to another wall
socket/phone socket, just replace the handset and your machine will
do the rest.
■ If this feature is set to On, but your machine does not connect
a fax call when you lift an extension or external phone
handset, press the Fax Receive Code 51 ( 91 for New
Zealand).
■ If you send faxes from a computer on the same phone line
and the machine intercepts them, set Fax Detect to Off.
■ Selecting Offmeans you’ll have to activate the machine
yourself by pressing Mono Start or Colour Start on the
machine
—OR—
Press 51 ( 91 for New Zealand) on the external or
extension phone if you are not at your machine.
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 3.
Use ▲ or ▼ to select On(or Off).
Press Menu/Set.
(Fax).
3.Fax Detect
4
Press Stop/Exit.
4 - 4 SETUP RECEIVE
Fax Detect (FAX-1840C only)
When you use this feature, you don’t have to press Mono Start or
Colour Start, or the Fax Receive Code 51 when you answer a
fax call. Selecting Fax Detect:Onallows the machine to receive
fax calls automatically, even if you lift the handset of an extension or
external phone. When you see Receivingon the LCD or when you
hear (chirps) through the handset of an extension phone connected
to another phone socket, just replace the handset and your machine
will do the rest. Selecting Semilets the machine receive the call only
if you’ve answered it at the machine.
■ If this feature is set to On, but your machine does not connect
a fax call when you lift an extension or external phone
handset, press the Fax Receive Code 51.
■ If you send faxes from a computer on the same phone line
and the machine intercepts them, set Fax Detect to Off.
■ Selecting Offmeans you’ll have to activate the machine
yourself by pressing Mono Start or Colour Start on the
machine
—OR—
Press 51on the external or extension phone if you are not
1
2
3
If it is not illuminated in green, press
(Fax).
Press Menu/Set, 2, 1, 3.
Use ▲ or ▼ to select On, Semior
Off.
3.Fax Detect
Press Menu/Set.
4
Press Stop/Exit.
SETUP RECEIVE 4 - 5
Printing a reduced incoming fax
(Auto Reduction)
If you choose Reduction:On, the machine automatically reduces
an incoming fax to fit on one page of A4, letter or legal size paper.
The machine calculates the reduction ratio by using the page size of
the document and your Paper Size setting (Menu/Set, 1, 3).
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 5.
Use ▲ or ▼ to select On(or Off).
Press Menu/Set.
(Fax).
5.Auto Reduction
4
Press Stop/Exit.
■ Turn on this setting if you receive faxes that are split on two
pages. However, if the document is too long, the machine
may print it on two pages.
■ If left and right margins are cut off, turn on this setting.
Receiving a fax at the end of a conversation
At the end of a conversation you can ask the other party to fax you
information before you both hang up.
1
2
3
Ask the other party to place the document in their machine and
to press Start or Send key.
When you hear the other machine’s CNG tones (beeps), press
Mono Start or Colour Start.
If you picked up the handset, replace it.
4 - 6 SETUP RECEIVE
Printing a fax from the memory
If you have selected Fax Forwarding or Fax Storage (Menu/Set, 2,
5, 1), you can still print a fax from the memory when you are at your
1
2
Press Menu/Set, 2, 5, 3.
Press Mono Start.
3.Print Document
Reception into memory
(Not available for colour fax reception)
As soon as the paper tray becomes empty during fax reception, the
screen will display No Paper Fed; please put some paper in the
If the Memory Receiveis Onat this time...
The current fax reception will continue, with the remaining page(s)
being stored in memory, subject to available memory. Subsequent
incoming faxes will also be stored into memory until the memory is
full, following this no further incoming fax calls will be automatically
answered. To print all data put fresh paper in the paper tray and
press Mono Start or Colour Start.
If the Memory Receiveis Offat this time...
The current fax reception will continue, with the remaining page(s)
being stored in memory, subject to available memory. Subsequent
incoming fax calls will not be automatically answered until fresh
paper is put in the paper tray. To print the last fax received, put paper
in the paper tray and press Mono Start or Colour Start.
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 6.
Use ▲ or ▼ to select On(or Off).
Press Menu/Set.
(Fax).
6.Memory Receive
4
Press Stop/Exit.
SETUP RECEIVE 4 - 7
Polling
Polling is the process of retrieving faxes from another fax machine.
You can use your machine to 'poll' other machines, or you can have
someone poll your machine.
Everyone who is involved in Polling needs to set up their fax
machines for Polling. When someone polls your machine to receive
a fax, they pay for the call. If you poll someone's fax machine to
receive a fax, you pay for the call.
Some fax machines do not respond to the Polling feature.
Secure Polling
Secure Polling is a way to keep your documents and others from
falling into the wrong hands while the machine is set up for polling.
You can use Secure Polling only with another Brother fax machine.
Anyone who polls to receive a fax must enter the polling secure code.
Setup for Polling Receive (Standard)
Polling Receive is when you call another fax machine to receive a fax
from it.
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 7.
Press ▲ or ▼ to select Standard.
(Fax).
7.Polling RX
Press Menu/Set.
4
Enter the fax number you are polling.
Press Mono Start or Colour Start.
4 - 8 SETUP RECEIVE
Setup for Polling Receive with Secure Code
You need to make sure you are using the same secure code as the
other party.
1
2
3
If it is not illuminated in green, press
(Fax).
Press Menu/Set, 2, 1, 7.
Press ▲ or ▼ to select
Polling:Secure.
7.Polling RX
Press Menu/Set.
4
Enter a four-digit secure code.
This is the same as the security code of the fax machine you are
polling.
Press Menu/Set.
5
6
Enter the fax number you are polling.
Press Mono Start or Colour Start.
Setup Delayed Polling Receive
You can set the machine to begin Polling Receive at a later time.
1
2
3
If it is not illuminated in green, press
(Fax).
Press Menu/Set, 2, 1, 7.
Press ▲ or ▼ to select
Polling:Timer.
7.Polling RX
Press Menu/Set.
4
5
Enter the time (in 24-hour format) you want to begin polling.
For example, enter 21:45 for 9:45 PM.
Press Menu/Set.
Enter the fax number you are polling.
Press Mono Start or Colour Start.
The machine makes the polling call at the time you entered.
You can set up only one Delayed Polling.
SETUP RECEIVE 4 - 9
Sequential Polling
The machine can request documents from several fax units in a
single operation. You just specify several destinations in Step 5.
Afterwards, a Sequential Polling Report will be printed.
1
2
3
If it is not illuminated in green, press
(Fax).
Press Menu/Set, 2, 1, 7.
Press ▲ or ▼ to choose Standard,
Secureor Timer.
7.Polling RX
Press Menu/Set when the screen displays the setting you
want.
4
If you selected Standard, go to Step 5.
■ If you selected Secure, enter a four-digit number and press
Menu/Set, and then go to Step 5.
■ If you selected Timer, enter the time (in 24-hour format) you
want to begin polling and press Menu/Set, and then go to
Step 5.
5
6
Specify the destination fax machines, which you wish to poll by
press Menu/Set between each location.
Press Mono Start or Colour Start.
The machine polls each number or group in turn for a document.
Press Stop/Exit while the machine is dialling to cancel the
polling process.
To cancel all sequential polling receive jobs, press Menu/Set,
4 - 10 SETUP RECEIVE
Quick-Dial numbers and
dialling options
5
Storing numbers for easy dialling
You can set up your machine to do following types of easy dialling:
One-Touch, Speed-Dial and Groups for Broadcasting faxes. When
you dial a quick-dial number, the LCD shows the name, if you stored
it, or the number.
If you lose electrical power, the quick-dial numbers that are in
the memory will not be lost.
Storing One-Touch Dial numbers
Your machine has One-Touch keys where you can
store fax or phone numbers for automatic dialling.
Two numbers can be stored on each One-Touch
key. To access the second number, which is shown
in a black square on the control panel, hold down
One-Touch keys are located on the left side of the
control panel.
1
2
Press Menu/Set, 2, 3, 1.
Press the One-Touch key where
you want to store a number.
Set Quick-Dial
1.One-Touch Dial
3
Enter the phone or fax number (up to 20 digits).
Press Menu/Set.
■ If you want to enter a pause in the dialling sequence (for
example, to access an outside line), press Redial/Pause
as you are entering the digits.
Each key press of Redial/Pause enters a 3.5 second
pause when the number is dialled, displayed by a dash on
the screen.
QUICK-DIAL NUMBERS AND DIALLING OPTIONS 5 - 1
4
5
Use the dial pad to enter the name (up to 15 characters).
Press Menu/Set.
—OR—
Press Menu/Set to store the number without a name.
Go to Step 2 to store another One-Touch number.
—OR—
Press Stop/Exit.
Storing Speed-Dial numbers
You can store Speed-Dial numbers, so that when you dial you will
only have to press a few keys (Search/Speed Dial, #, the two-digit
number, and Mono Start or Colour Start). The machine can store
40 Speed-Dial numbers.
1
2
Press Menu/Set, 2, 3, 2.
Use the dial pad to enter a two-digit
Speed-Dial location number (01-40).
2.Speed Dial
(For example, press 05.)
Press Menu/Set.
3
4
Enter the phone or fax number (up to 20 digits).
Press Menu/Set.
Use the dial pad to enter the name (up to 15 characters).
Press Menu/Set.
—OR—
Press Menu/Set to store the number without a name.
Go to Step 2 to store another Speed-Dial number.
—OR—
5
Press Stop/Exit.
5 - 2 QUICK-DIAL NUMBERS AND DIALLING OPTIONS
Changing One-Touch and Speed-Dial numbers
If you try to store a One-Touch or Speed-Dial number where a
number has already been stored, the LCD will show the name that
has been stored there (or number) and will ask you to do one of the
following:
1
Press 1 to change the stored
05:Mike
number.
1.Change 2.Exit
—OR—
Press 2 to exit without making a change.
How to change the stored number or name:
■ If you want to change a character, use
or
to position
the cursor under the character you want to change, and then
type over it.
■ If you want to erase the whole number or whole name, press
Stop/Exit when the cursor is under the first digit or letter.
The characters above and to the right of the cursor will be
deleted.
2
3
Enter a new number.
Press Menu/Set.
Follow the directions beginning at Step 4 in Storing One-Touch
Dial numbers and Storing Speed-Dial numbers. (See page 5-1
QUICK-DIAL NUMBERS AND DIALLING OPTIONS 5 - 3
Setting up Groups for Broadcasting
Groups, which can be stored on a One-Touch key or a Speed-Dial
location, allow you to send the same fax message to many fax
numbers by pressing only a One-Touch key and Mono Start or
Search/Speed Dial, #, the two-digit location and Mono Start.
First, you will need to store each fax number as a One-Touch or
Speed-Dial number. Then, you can combine them into a Group,
Each Group uses up a One-Touch key or a Speed-Dial location.
Finally, you can have up to six small Groups, or you can assign up to
49 numbers to one large Group.
1
2
Press Menu/Set, 2, 3, 3.
Decide where you wish to store the
Group.
3.Setup Groups
—AND—
Press a One-Touch key.
—OR—
Press Search/Speed Dial and enter the two-digit location,
and then press Menu/Set.
3
4
Use the dial pad to enter the Group number (1 to 6).
Press Menu/Set.
(For example, press 1 for Group 1.)
To include One-Touch or Speed-Dial numbers in the Group,
enter them as follows.
For example, for One-Touch key 2, press One-Touch key 2. For
a number in a black square, such as One-Touch key
, press
Shift and One-Touch key
.
For Speed-Dial location 09, press Search/Speed Dial, and
then press 09 on the dial pad. The LCD shows 02, #09(or
06, #09).
5 - 4 QUICK-DIAL NUMBERS AND DIALLING OPTIONS
5
6
Press Menu/Set to accept the numbers for this Group.
the Group.
Press Menu/Set.
(For example, NEW CLIENTS)
7
Press Stop/Exit.
You can print a list of all One-Touch and Speed-Dial numbers.
marked in the GROUP column.
QUICK-DIAL NUMBERS AND DIALLING OPTIONS 5 - 5
Dialling options
Access codes and credit card numbers
Sometimes you may want to choose from several long distance
carriers when you make a call. Rates may vary depending on the time
and destination. To take advantage of low rates, you can store the
access codes or long-distance carriers and credit card numbers as
One-Touch and Speed-Dial numbers. You can store these long
dialling sequences by dividing them and setting them up as separate
One-Touch and Speed-Dial numbers in any combination. You can
For example, perhaps you have stored ‘555’ on One-Touch key 1 and
‘7000’ on One-Touch key 2. If you press One-Touch key 1,
One-Touch key 2, and Mono Start or Colour Start, you will dial
‘555-7000’.
To temporarily change a number, you can substitute part of the
number with manual dialling using the dial pad.
For example, to change the number to 555-7001 you could press
One-Touch key 1 and then press 7001 using the dialling pad.
If you must wait for another dial tone or signal at any point in the
dialling sequence, store a pause there in the number by
pressing Redial/Pause. Each key press adds a 3.5-second
delay.
Pause
Press Redial/Pause to insert a 3.5-second pause between
numbers. If you are dialling overseas, you can press Redial/Pause
as many times as needed to increase the length of the pause.
5 - 6 QUICK-DIAL NUMBERS AND DIALLING OPTIONS
Tone or Pulse (Not available in New Zealand)
If you have a Pulse dialling service, but need to send Tone signals
(for example, for telephone banking), follow the instructions below. If
you have Touch Tone service, you will not need this feature to send
tone signals.
1
For FAX-1840C, lift the handset.
—OR—
For MFC-3240C, lift the handset of the external telephone.
2
Press # on the machine’s control panel. Any digits dialled after
this will send tone signals.
When you hang up, the machine will return to the Pulse dialling
service.
QUICK-DIAL NUMBERS AND DIALLING OPTIONS 5 - 7
Telephone (voice) operation
(FAX-1840C only)
You can use the machine to make voice telephone calls by dialling
manually or by using Search, One-Touch Dial or Speed-Dial
memory. You can use the handset to make and receive calls.
When you dial a Quick-Dial number, the LCD shows the name you’ve
stored, or if you haven’t stored a name, the fax number you’ve
stored.
How to dial
Making a telephone call
1
2
Pick up the handset.
When you hear a dial tone, dial the number using the dial pad,
One-Touch, Speed-Dial and Search.
3
To hang up, replace the handset.
Tel
This key is used to enter into a conversation after having picked up
the handset of an external telephone in F/T pseudo-ringing.
Also, if you press Hook/Hold/Recall when you are talking lifting the
external telephone’s handset with the other end, you can hear the
other end from the machine’s monitor speaker, but the other end
cannot hear you.
Mute (FAX-1840C only)
1
2
Press Hook/Hold/Recall to put a call on Hold.
You can replace the handset without disconnecting the call.
Pick up the machine handset to release the call from Hold.
Picking up an extension handset will not release the call from
Hold.
5 - 8 QUICK-DIAL NUMBERS AND DIALLING OPTIONS
Remote Fax Options
(Not available for colour faxes)
6
You can only use one remote fax option at a time:
Fax Forwarding—OR—Fax Storage—OR—Off.
You can change your selection at any time (Menu/Set, 2, 5, 1).
Setting up Fax Forwarding
When you select Fax Forward, your machine stores the received fax
in the memory. The machine will then dial the fax number you’ve
programmed and forwards the fax message.
1
2
Press Menu/Set, 2, 5, 1.
Press ▲ or ▼ to select
Fax Forward.
1.Fwd/Page/Store
Press Menu/Set.
The LCD will ask you to enter the fax number to which faxes will
be forwarded.
3
4
Enter the forwarding number (up to 20 digits).
Press Menu/Set.
Press ▲ or ▼ to select Onor Off.
Backup Print:On
Press Menu/Set.
If you select Backup Print:On, the machine will also print the
fax at your machine so you will have a copy if there is a power
failure before it is forwarded.
5
Press Stop/Exit.
REMOTE FAX OPTIONS 6 - 1
Setting Fax Storage
If you select Fax Storage, your machine stores the received fax in the
memory. You will be able to retrieve fax messages from another
location using the Remote Retrieval commands.
1
2
Press Menu/Set, 2, 5, 1.
Press ▲ or ▼ to select
Fax Storage.
1.Fwd/Page/Store
Press Menu/Set.
3
Press Stop/Exit.
If you have set Fax Storage, a backup copy of the received fax
will automatically be printed at the machine.
Turning off Remote Fax Options
If you set the Remote Fax Options to Offand there are faxes in your
machine’s memory, the LCD will give you two options.
■ If you press 1, all unprinted faxes will be printed and erased
before the setting turns off. If a backup copy has already been
printed it will not be printed again.
■ If you press 2, the memory will not be erased and the setting will
be unchanged.
6 - 2 REMOTE FAX OPTIONS
Setting your Remote Access Code
The remote access code lets you access the Remote Retrieval
features when you are away from your machine. Before you use the
remote access and retrieval features, you have to set up your own
code. The default code is inactive code (--- ).
1
2
Press Menu/Set, 2, 5, 2.
Enter a three-digit code using
2.Remote Access
numbers 0-9,
.
Press Menu/Set. (The preset ‘ ’ cannot be changed.)
Do not use the same code which is set in your Fax Receive
Code ( 51, 91 for New Zealand) or Telephone Answer
Code (#51, #91 for New Zealand).
3
Press Stop/Exit.
You can change your code at any time by entering a new one.
If you want to make your code inactive, press Stop/Exit in Step
2 to restore the inactive setting (--- ).
REMOTE FAX OPTIONS 6 - 3
Remote Retrieval
You can call your machine from any touch tone telephone or fax
machine, then use the Remote Access Code and remote commands
to retrieve fax messages.
Using your Remote Access Code
1
2
3
Dial your fax number from a telephone or another fax machine
using touch tone.
When your machine answers, immediately enter your Remote
Access Code (3 digits followed by ).
The machine signals if it has received messages:
1 long beep — Fax messages
No beeps — No messages
4
The machine gives two short beeps to tell you to enter a
command. The machine will hang up if you wait longer than 30
seconds to enter a command. The machine will beep three
times, if you enter an invalid command.
5
6
Press 90 to reset the machine when you’ve finished.
Hang up.
If your machine is set to Manualmode and you want to use the
remote retrieval features, you can access your machine by
waiting about 2 minutes after it starts ringing, and then entering
the Remote Access Code within 30 seconds.
6 - 4 REMOTE FAX OPTIONS
Remote commands
Follow the commands below to access features when you are away
from the machine. When you call the machine and enter your
Remote Access Code (3 digits followed by ), the system will give
two short beeps and you must enter a remote command.
Remote commands
Operation details
95 Change the Fax Forwarding
or Fax Storage settings
1 OFF
You can select Offafter you have retrieved
or erased all your messages.
2 Fax Forwarding
4 Fax Forwarding number
6 Fax Storage
If you hear one long beep, the change has
been accepted. If you hear three short beeps,
you cannot change it because the conditions
have not been met (for example, registering a
Fax Forwarding number). You can register
your Fax Forwarding number by entering 4.
on page 6-6.) Once you have registered the
number, Fax Forwarding will work.
96 Retrieve a fax
2 Retrieve all faxes
Enter the number of a remote fax machine to
receive stored fax message(s). (See page
6-6.)
3 Erase faxes from the
memory
If you hear one long beep, fax messages
have been erased from the memory.
97 Check the receiving status
You can check whether your machine has
received any faxes. If yes, you will hear one
long beep. If no, you will hear three short
beeps.
1 Document
98 Change the Receive Mode
1 External TAD
2 Fax/Tel
If you hear one long beep, your change has
been accepted.
3 Fax Only
90 Exit
Press 90 to exit Remote Retrieval. Wait for
the long beep, then replace the handset.
REMOTE FAX OPTIONS 6 - 5
Retrieving fax messages
You can call your machine from any touch tone phone and have your
fax messages sent to a fax machine.
1
2
Dial your fax number.
When your machine answers, immediately enter your Remote
Access Code (3 digits followed by ). If you hear one long
beep, you have messages.
3
4
As soon as you hear two short beeps, use the dial pad to press
962.
Wait for the long beep, and then use the dial pad to enter the
number of the remote fax machine where you want your fax
messages sent to followed by ## (up to 20 digits).
You cannot use
you want to store a pause.
and # as dial numbers. However, press # if
5
Hang up after you hear your machine beep. Your machine will
call the other machine, which will then print your fax messages.
Changing your Fax Forwarding number
You can change the default setting of your fax forwarding number
from another telephone or fax machine using touch tone.
1
2
Dial your fax number.
When your machine answers, immediately enter your Remote
Access Code (3 digits followed by ). If you hear one long
beep, you have messages.
3
4
When you hear two short beeps, use the dial pad to press 954.
Wait for the long beep, and then use the dial pad to enter the
new number of the remote fax machine where you want your fax
messages forwarded followed by ## (up to 20 digits).
You cannot use
you want to store a pause.
and # as dial numbers. However, press # if
5
Hang up after you hear your machine beep.
6 - 6 REMOTE FAX OPTIONS
Printing reports
7
Fax settings and activity
You need to set up the Transmission Verification Report and Journal
Period in the menu table.
Press Menu/Set, 2, 4, 1.
1.Transmission
—OR—
Press Menu/Set, 2, 4, 2.
2.Journal Period
Customizing the Transmission Verification
Report
You can use the Transmission Report as proof that you sent a fax.
This report lists the time and date of transmission and whether the
transmission was successful (OK). If you select Onor On+Image, the
report will print for every fax you send.
If you send a lot of faxes to the same place, you may need more than
the job numbers to know which faxes you must send again. Selecting
On+Imageor Off+Imagewill print a section of the fax’s first page
on the report to help you remember.
When the Verification Report is turned Offor
Trans:Off+Image, the Report will only print if there is a
transmission error, with NG in the RESULT column.
1
2
Press Menu/Set, 2, 4, 1.
Press ▲ or ▼ to select Off+Image,
On, On+Imageor Off.
1.Transmission
Press Menu/Set.
3
Press Stop/Exit.
PRINTING REPORTS 7 - 1
Setting the Journal Period
You can set the machine to print a journal at specific intervals (every
50 faxes, 6, 12 or 24 hours, 2 or 7 days). If you set the interval to Off,
you can print the report by following the steps on the next page.
The default setting is Every 50 Faxes.
1
2
Press Menu/Set, 2, 4, 2.
Press ▲ or ▼ to choose an interval.
Press Menu/Set.
2.Journal Period
(If you choose 7 days, the LCD will ask you to choose a day on
which to begin the 7-day countdown.)
3
4
Enter the time to begin printing in 24-hour format.
Press Menu/Set.
(For example: enter 19:45 for 7:45 PM.)
Press Stop/Exit.
If you select 6, 12, 24 hours, 2 or 7 days, the machine will print
the report at the selected time and then erase all jobs from its
memory. If the machine’s memory becomes full with 200 jobs
before the time you selected has passed, the machine will print
the Journal early and then erase all jobs from memory. If you
want an extra report before it is due to print, you can print it
without erasing the jobs from memory.
If you select Every 50 Faxes, the machine will print the
Journal when the machine has stored 50 jobs.
7 - 2 PRINTING REPORTS
Printing reports
Following reports are available:
Prints the Help List so you can see at-a-glance
how to quickly program your machine.
1.Help List
2.Quick-Dial
Lists names and numbers stored in the
One-Touch and Speed-Dial memory, in numerical
order.
Lists information about the last incoming and
outgoing faxes.
3.Fax Journal
(TX means Transmit.) (RX means Receive.)
Prints a Transmission Verification Report for your
last transmission.
4.XMIT Verify
How to print a report
1
For MFC-3240C, press Menu/Set, 4.
—OR—
For FAX-1840C, press Ink Management/Reports while
holding down the Shift key.
2
Press ▲ or ▼ to select the report you want.
Press Menu/Set.
—OR—
Enter the number of the report you want to print.
For example, press 1 to print the Help List.
Press Mono Start.
3
PRINTING REPORTS 7 - 3
Making copies
8
Using the machine as a copier
You can use your machine as a copier, making up to 99 copies at a
time.
Enter Copy mode
Before making copies, make sure that
(Copy) is illuminated
in green. If it is not, press (Copy) to enter Copy mode. The
default setting is Fax. You can change the number of seconds or
The LCD shows the default copy setting
Copy Ratio
Quality
No of Copies
8 - 1 MAKING COPIES
Making a single copy
1
2
Press
(Copy) to illuminate it in green.
Load your document.
Press Mono Start or Colour Start.
3
To stop copying, press Stop/Exit.
Making multiple copies
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
Press Mono Start or Colour Start.
Stop copying
To stop copying, press Stop/Exit.
MAKING COPIES 8 - 2
Using the temporary Copy keys
(Temporary settings)
When you want to quickly change the copy settings temporarily for
the next copy, use the temporary Copy keys. You can use different
combinations.
Temporary Copy Keys
These settings are temporary, and the machine returns to its
default settings 60 seconds after it finishes copying. However if
you have set the Mode Timer to 0 or 30 seconds, the machine
returns to the default settings after the number of seconds that
You can save the copy settings you use most often by setting
8 - 3 MAKING COPIES
Increasing copy speed or quality
You can select the copy quality. The default setting is Normal.
Press Quality Normal
Recommended mode for ordinary
printouts. Good copy quality with
adequate copy speed.
Fast
Fast copy speed and lowest ink
consumption. Use Fastto save
time (document to be proof-read,
large documents or many copies).
and
or
Best
Use this mode to copy precise
images such as photographs. Best
uses the highest resolution and
slowest speed.
1
2
Press
(Copy) to illuminate it in green.
Load your document.
3
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Quality.
Press ▲ or ▼ to choose the copy quality (Fast, Normalor
Best).
Press Menu/Set.
6
Press Mono Start or Colour Start.
MAKING COPIES 8 - 4
Changing the temporary copy settings
Use the Options key to quickly set the following copy settings
temporarily for the next copy.
Press
Options
Menu Selections
Options
Factory
Setting
Page
select
select
Enlarge/Reduce
50%/69%/78%/83%/
93%/97%/100%/
104%/142%/186%/
198%/200%/
100%
8-6
Custom(25-400%)
Paper Type
Paper Size
Plain/Inkjet/
Glossy/Transparen
cy
Plain
A4
8-8
8-8
Letter/Legal/
A4/A5/
10(W) x 15(H)cm
Brightness
Contrast
-
-
+
+
-
-
+
+
Page Layout
Off(1 in 1)/
2 in 1 (P)/
2 in 1 (L)/
4 in 1 (P)/
4 in 1 (L)
Off(1in 8-12
1)
No. of Copies
No. of Copies:01 01
(01-99)
After you choose your settings by pressing Menu/Set, the LCD
shows Set temporarily.
Press Mono Start or Colour Start if you’re finished choosing
settings.
—OR—
Press ▲ or ▼ to select more settings.
8 - 5 MAKING COPIES
Enlarging or reducing the image copied
You can select the following enlargement or reduction ratios.
Custom(25-400%)allows you to enter a ratio from 25% to 400%.
Press Options
Custom(25-400%)
200%
198% 10x15cm→A4
186%10x15cm→LTR
142% A5→A4
104% EXE→LTR
100%
and
Enlarge/Reduce
or
to select
97% LTR→A4
93% A4→LTR
83% LGL→A4
78% LGL→LTR
69% A4→A5
50%
MAKING COPIES 8 - 6
1
2
3
Press
Load your document.
(Copy) to illuminate it in green.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Enlarge/Reduce.
Press Menu/Set.
Press ▲ or ▼ to select the enlargement or reduction ratio you
want.
Press Menu/Set.
—OR—
You can select Custom(25-400%)and press Menu/Set.
Use the dial pad to enter an enlargement or reduction ratio from
25%to 400%.
Press Menu/Set.
(For example, press 5 3 to enter 53%.)
Press Mono Start or Colour Start.
6
Special Copy Options 2 in1 (P), 2 in 1 (L), 4 in 1 (P) or 4 in 1 (L)
are not available with Enlarge/Reduce.
8 - 7 MAKING COPIES
Setting paper type
If you are copying on special paper, be sure to select the type of
paper you are using so you will get the best print quality.
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Paper Type.
Press Menu/Set.
Press ▲ or ▼ to select the type of paper you are using (Plain,
Inkjet, Glossyor Transparency).
Press Menu/Set.
6
Press Mono Start or Colour Start.
You can change the default Paper Type setting at any time.
Setting paper size
If copying on paper other than A4 size, you will need to change the
paper size setting.
You can copy on Letter, Legal, A4, A5 or Photo Card (10(W) x
15(H) cm) paper.
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Paper Size.
Press Menu/Set.
Press ▲ or ▼ to select the size of paper you are using (Letter,
Legal, A4, A5or 10(W) x 15(H)cm).
Press Menu/Set.
6
Press Mono Start or Colour Start.
MAKING COPIES 8 - 8
Adjusting brightness
You can adjust the copy brightness to make copies darker or lighter.
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Brightness.
Press Menu/Set.
Press ▲ to make a lighter copy.
—OR—
Press ▼ to make a darker copy.
Press Menu/Set.
6
Press Mono Start or Colour Start.
Adjusting contrast
You can adjust the copy contrast to help an image look sharper and
more vivid.
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Contrast.
Press Menu/Set.
Press ▲ to increase the contrast.
—OR—
Press ▼ to decrease the contrast.
Press Menu/Set.
6
Press Mono Start or Colour Start.
8 - 9 MAKING COPIES
Making N in 1 copies (Page Layout)
You can reduce the amount of copies by using the N in 1 copy
feature. This allows you to copy two or four pages onto one page,
which allows you to save paper.
■ Please make sure Paper Size is set to A4or Letter.
■ You can use N in 1 copy feature with 100% copy size only.
■ (P) means Portrait and (L) means Landscape.
1
2
3
Press
(Copy) to illuminate it in green.
Load your document.
Use the dial pad to enter the number of copies you want
(up to 99).
4
5
Press Options and ▲ or ▼ to select Page Layout.
Press Menu/Set.
Press ▲ or ▼ to select 2 in 1 (P), 2 in 1 (L), 4 in 1 (P),
4 in 1 (L)or Off(1 in 1).
Press Menu/Set.
6
7
Press Mono Start or Colour Start to scan the document.
The machine scans document and starts printing.
If Glossyhas been selected in the Paper Type setting for N in
1 copies, the machine will print the images as if Plain paper had
been selected.
■ If you are producing multiple colour copies, N in 1 copies are
not available.
■ N in 1 colour copies are not available for FAX-1840C and
MFC-3240C.
MAKING COPIES 8 - 10
Place document face down in the direction shown below.
2 in 1 (P)
2 in 1 (L)
4 in 1 (P)
4 in 1 (L)
8 - 11 MAKING COPIES
Changing the default copy settings
You can save the copy settings you use most often by setting them
as default. These settings will remain until you change them again.
Increasing copy speed or quality
1
2
Press Menu/Set, 3, 1.
Press ▲ or ▼ to select Normal,
Bestor Fast.
1.Quality
Press Menu/Set.
3
Press Stop/Exit.
Adjusting brightness
1
2
Press Menu/Set, 3, 2.
Press ▲ to make a lighter copy.
—OR—
2.Brightness
Press ▼ to make a darker copy.
Press Menu/Set.
3
Press Stop/Exit.
MAKING COPIES 8 - 12
Adjusting contrast
You can change the contrast to help an image look sharper and more
vivid.
1
2
Press Menu/Set, 3, 3.
Press ▲ to increase the contrast.
—OR—
3.Contrast
Press ▼ to decrease the contrast.
Press Menu/Set.
3
Press Stop/Exit.
Adjusting colour saturation
1
2
Press Menu/Set, 3, 4.
Press ▲ or ▼ to select Red, Green
or Blue.
4.Color Adjust
Press Menu/Set.
3
4
Press ▲ to increase the colour saturation.
—OR—
Press ▼ to decrease the colour saturation.
Press Menu/Set.
Return to Step 2 to select the next colour.
—OR—
Press Stop/Exit.
8 - 13 MAKING COPIES
Legal limitations
Colour reproductions of certain documents are illegal and may result
in either criminal or civil liability. This memorandum is intended to be
a guide rather than a complete listing of every possible prohibition. In
case of doubt, we suggest that you check with relevant authorities as
to any particular questionable documents.
The following are examples of documents which should not be
copied:
■ Money
■ Bonds or other certificates of debt
■ Certificates of Deposit
■ Service or Draft papers of the Armed Forces
■ Passports
■ Postage Stamps (cancelled or uncancelled)
■ Immigration Papers
■ Welfare documents
■ Cheques or Drafts drawn by Governmental Agencies
■ Documents, badges or insignias of identification
■ Licences and Certificates of Title to motor vehicles
Works subject to Copyright cannot be copied. Sections of works
subject to Copyright can be copied for ‘fair use’. Multiple copies
would indicate improper use.
Works of art should be considered as works subject to Copyright.
MAKING COPIES 8 - 14
Important information
9
Important Information for Australia
IMPORTANT-For Your Safety.
To ensure safe operation the three-pin plug supplied must be
inserted only into a standard three-pin power point which is
effectively grounded through the normal household wiring.
Extension cords used with the equipment must be three-conductor
and be correctly wired to provide connection to ground. Incorrectly
wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply
that the power is grounded and that the installation is completely
safe. For your safety, if in any doubt about the effective grounding of
the power, consult a qualified electrician.
Disconnect device
This machine must be installed near a power outlet, which is easily
accessible. In case of emergencies, you must disconnect the power
cord from the power outlet in order to shut off power completely.
9 - 1 IMPORTANT INFORMATION
International ENERGY STAR® Compliance Statement
®
The purpose of the International ENERGY STAR Program is to
promote the development and popularization of energy-efficient
office equipment.
®
As an ENERGY STAR Partner, Brother Industries, Ltd. has determined
®
that this product meets the ENERGY STAR guidelines for energy
efficiency.
Important safety instructions
1
2
3
4
Read all of these instructions.
Save them for later reference.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall socket before cleaning. Do not
use liquid or aerosol cleaners. Use a damp cloth for cleaning.
5
6
Do not use this product near water.
Do not place this product on an unstable cart, stand, or table.
The product may fall, causing serious damage to the product.
7
Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the
product and to protect it from overheating, these openings must
not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or
over a radiator or heater. This product should never be placed
in a built-in installation unless proper ventilation is provided.
8
This product should be operated from the type of power source
indicated on the label. If you are not sure of the type of power
available, call your dealer or local power company.
IMPORTANT INFORMATION 9 - 2
9
This product is equipped with a 3-wire grounded plug, a plug
having a third (grounded) pin. This plug will only fit into a
grounded power outlet. This is a safety feature. If you are unable
to insert the plug into the outlet, call your electrician to replace
your obsolete outlet. Do not defeat the purpose of the grounded
plug.
10 Do not allow anything to rest on the power cord. Do not place
this product where people can walk on the cord.
11 Do not place anything in front of the machine that will block
received faxes. Do not place anything in the path of received
faxes.
12 Do not touch a document during printing.
13 Never push objects of any kind into this product through cabinet
slots, since they may touch dangerous voltage points or short
out parts resulting in a risk of fire or electric shock. Never spill
liquid of any kind on the product.
14 Do not attempt to service this product yourself, because
opening or removing covers may expose you to dangerous
voltage points and/or other risks. Refer all servicing to service
personnel.
15 Wait until pages have exited the machine before picking them
up.
16 Unplug this product from the wall outlet and refer servicing to
Authorized Service Personnel under the following conditions:
■ When the power cord is damaged or frayed.
■ If liquid has been spilled into the product.
■ If the product has been exposed to rain or water.
■ If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the
product to normal operation.
■ If the product has been dropped or the cabinet has been
damaged.
■ If the product exhibits a distinct change in performance,
indicating a need for service.
9 - 3 IMPORTANT INFORMATION
Important Information for New Zealand
Important Safety Instructions
1
2
3
4
Read all of these instructions.
Save them for later reference.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not
use liquid or aerosol cleaners. Use a damp cloth for cleaning.
5
The grant of a Telepermit for any item of terminal equipment
indicates only that Telecom has accepted that the item complies
with minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does
it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with
another item of Telepermitted equipment of a different make or
model, nor does it imply that any product is compatible with all
of Telecom’s network services.
6
7
This equipment does not fully meet Telecom’s impedance
requirements. Performance limitations may occur when used in
conjunction with some parts of the network. Telecom will accept
no responsibility should difficulties arise in such circumstances.
If a charge for local calls is acceptable, the “Dial Button” should
not be used for local calls. Only the 7-digits of the local number
should be dialled from your telephone. Do not dial the area code
digit or the “0” prefix.
8
9
This equipment shall not be set to make automatic calls to the
Telecom ‘111’ Emergency Service.
This equipment should not be used under any circumstances
which may constitute a nuisance to other Telecom customers.
10 Not all telephones will respond to incoming ringing when
connected to the extension socket.
11 The answer delay setting of this equipment shall not be set to
less than the default setting as this will destroy Caller ID
information.
IMPORTANT INFORMATION 9 - 4
12 All persons using this device for recording telephone
conversations shall comply with New Zealand law. This requires
that at least one party to the conversation is to be aware that it
is being recorded. In addition, the Principles enumerated in the
Privacy Act 1993 shall be complied with in respect to the nature
of the personal information collected, the purpose for its
collection, how it is to be used and what it disclosed to any other
party.
13 Do not place this product on an unstable surface, stand, or table.
The product may fall, causing serious damage to the product.
14 Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the
product and to protect it from overheating, these openings must
not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or
over a radiator or heater. This product should not be placed in a
built-in installation unless proper ventilation is provided.
15 This product should be operated from the type of power source
indicated on the label. If you are not sure of the type of power
available, consult with your dealer or local power company.
16 This product is equipped with a 3-wire earthed plug. This plug
will fit into only an earthed socket. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete socket. Do not defeat the
purpose of an earthed plug.
17 Do not allow anything to rest on the power cord. Do not locate
this product where people can walk on the cord.
18 Do not place anything in front of the machine that will block
received faxes. Do not place anything in the path of received
faxes.
19 Do not touch a document during printing.
20 Never push objects of any kind into this product through cabinet
slots, since they may touch dangerous voltage points or short
out parts resulting in a risk of fire or electric shock. Never spill
liquid of any kind on the product.
9 - 5 IMPORTANT INFORMATION
21 Do not attempt to service this product yourself, because
opening or removing covers may expose you to dangerous
voltage points and/or other risks. Refer all servicing to service
personnel.
22 Unplug this product from the mains power and telephone line
sockets, and refer servicing to qualified Service Personnel
under the following conditions:
■ If the power cord is damaged or frayed.
■ If liquid has been spilled into the product.
■ If the product has been exposed to rain or water.
■ If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the
product to normal operation.
■ If the product has been dropped or the cabinet has been
damaged.
■ If the product exhibits a distinct change in performance,
indicating a need for service.
23 This unit will only work in conjunction with a tone signalling
(DTMF) telephone, but some telephones are not compatible.
Since noise or speech from the telephone can upset dialling
from this unit, errors may result if the devices are used together
in other than quiet conditions.
24 Where it is necessary to dial prefix digits, such as a Caller
Display override code (“0196” or “0197”), this unit will have to be
used in conjunction with an associated tone signalling (DTMF)
telephone.
25 Note that some telephones are not compatible with this unit and
dialling errors may result if the two devices are used together in
other than quiet conditions. The Telecom Faults Service is not
to be called should such problems arise. In such cases, it is
recommended that the prefix and wanted number are dialled
manually.
26 This equipment may not provide for the effective hand-over of a
call to another device connected to the same line.
IMPORTANT INFORMATION 9 - 6
IMPORTANT-For Your Safety
To ensure safe operation the three-pin plug supplied must be
inserted only into a standard three-pin power point which is
effectively grounded through the normal household wiring.
Extension cords used with the equipment must be three-conductor
and be correctly wired to provide connection to ground. Incorrectly
wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply
that the power is grounded and that the installation is completely
safe. For your safety, if in any doubt about the effective grounding of
the power, consult a qualified electrician.
Disconnect device
This machine must be installed near a power outlet, which is easily
accessible. In case of emergencies, you must disconnect the power
cord from the power outlet in order to shut off power completely.
IMPORTANT NOTICE
Under power failure conditions, this telephone may not operate.
Please ensure that a separate telephone, not dependent on local
power, is available for emergency use in emergencies.
9 - 7 IMPORTANT INFORMATION
Important Information for Some
Countries
Important Safety Instructions
1
2
3
4
Read all of these instructions.
Save them for later reference.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not
use liquid or aerosol cleaners. Use a damp cloth for cleaning.
5
6
Do not place this product near water.
Do not place this product on an unstable cart, stand, or table.
The product may drop, causing serious damage to the product.
7
Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the
product and to protect it from overheating, these openings must
not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or on
a radiator or heater. This product should never be placed in a
built-in installation unless proper ventilation is provided.
8
9
This product should be operated from the type of power source
indicated on the label. If you are not sure of the type of power
available, consult with your dealer or local power company.
This product is equipped with a 2-wire grounding type plug or a
3-wire grounding type plug (Only for Singapore, Malaysia, Hong
Kong and India), a plug having two or three pins. This plug will
only fit into only a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not
defeat the purpose of the grounding-type plug.
10 Do not allow anything to rest on the power cord. Do not place
this product where people can walk on the cord.
IMPORTANT INFORMATION 9 - 8
11 If an extension cord is used with this product, make sure that the
total ampere ratings on the products plugged into the extension
cord do not exceed the extension cord ampere rating.
12 Do not place anything in front of the machine that will block
received faxes. Do not place nything in the path of received
faxes.
13 Do not touch a document during printing.
14 Never push objects of any kind into this product through cabinet
slots, since they may touch dangerous voltage points or short
out parts resulting in the risk of fire or electric shock. Never spill
liquid of any kind on the product.
15 Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage points
and/or other risks, and may void your warranty. Please refer all
servicing to our Authorized Service Personnel. A list of
Authorized Service Centres has been included for your
convenience, or you may contact the Brother Dealer for Service.
16 Unplug this product from the wall outlet and refer servicing to
Authorized Service Personnel under the following conditions:
■ If the power cord is damaged or frayed.
■ If the product has been spilled by liquid.
■ If the product has been exposed to rain or water.
■ If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the
product to normal operation.
■ If the product has been dropped or the cabinet has been
damaged.
■ If the product exhibits a distinct change in performance,
indicating a need for service.
9 - 9 IMPORTANT INFORMATION
17 To protect your product against power surges, we recommend
the use of a power protection device (Surge Protector).
For protection against the risk of electrical shock, always
disconnect all cables from the wall outlet before servicing,
modifying or installing the equipment.
This equipment may not be used on coin service lines provided
by the telephone company or connected to party lines.
Brother cannot accept any financial or other responsibilities
that may be the result of your use of this information, including
direct, special or consequential damages. There are no
warranties extended or granted by this document.
IMPORTANT INFORMATION 9 - 10
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International
Corporation.
© 2004 Brother Industries, Ltd. All rights reserved.
Windows and Microsoft are registered trademarks of Microsoft in the
U.S. and other countries.
Macintosh and TrueType are registered trademarks of Apple
Computer, Inc.
PaperPort and OmniPage OCR are registered trademarks of
ScanSoft, Inc.
Presto! PageManager is a registered trademark of NewSoft
Technology Corporation.
Microdrive is a trademark of International Business Machine
Corporation.
SmartMedia is a registered trademark of Toshiba Corporation.
CompactFlash is a registered trademark of SanDisk Corporation.
Memory Stick is a registered trademark of Sony Corporation.
SecureDigital is a trademark of Matsushita Electric Industrial Co. Ltd.,
SanDisk Corporation and Toshiba Corporation.
SanDisk is a licensee of the SD and miniSD trademarks.
xD-Picture Card is a trademark of Fujifilm Co. Ltd., Toshiba
Corporation and Olympus Optical Co. Ltd.
Memory Stick Duo and MagicGate are trademarks of Sony
Corporation.
Each company whose software title is mentioned in this manual has
a Software License Agreement specific to its proprietary programs.
All other brand and product names mentioned in this User’s
Guide, the Software User’s Guide (MFC-3240C) are registered
trademarks of their respective companies.
9 - 11 IMPORTANT INFORMATION
Troubleshootingandroutine
maintenance
10
Troubleshooting
Error messages
As with any sophisticated office product, errors may occur. If this
happens, your machine identifies the problem and displays an error
message. The most common error messages are shown below.
You can correct most problems by yourself. If you need additional
help, the Brother Solutions Center offers latest FAQs and
troubleshooting tips.
ERROR MESSAGES
ERROR
CAUSE
ACTION
MESSAGE
Comm.Error
Poor phone line quality caused a
communication error.
Try the call again. If the problem continues, call
the telephone company and ask them to check
your phone line.
Connection
Fail
You tried to poll a fax machine that Check the other fax machine’s polling setup.
is not in Polled Waiting mode.
Cover is Open Top cover is not closed
Open, then close the top cover.
completely.
Data
Remaining
Print data remains in the
machine’s memory.
Re-start printing from your computer.
Print data remains in the
machine’s memory. The USB
cable was unplugged while the
computer was sending the data to
the machine.
Press Stop/Exit. The machine will cancel the
job and eject the page that is being printed.
Disconnected
Document Jam
The otherperson or other person’s Try to send or receive again.
fax machine stopped the call.
was longer than about 90 cm.
The document is jammed in the
machine.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 1
ERROR MESSAGES
ERROR
CAUSE
ACTION
MESSAGE
High
Temperature
The print head is too warm.
Allow the machine to cool down.
Ink Empty
One or more of the ink cartridges
Replace the ink cartridges.
available, black and white faxes
will be received into memory. If a
sending machine has a colour fax,
the machine’s ‘handshake’ will
request that the fax be sent as
black and white. If the sending
machine has the ability to convert
it, the colour fax will be received
into memory as a black and white
fax.
Low
Temperature
The print head is too cold.
Allow the machine to warm up.
Order a new ink cartridge.
Near Empty
One or more of the ink cartridges
machine has a colour fax, the
machine’s ‘handshake’ will
request that the fax be sent as
black and white. If the sending
machine has the ability to convert
it, the colour fax will be received
into memory as a black and white
fax.
10-23.)
No Cartridge
No Paper Fed
An ink cartridge is not properly
installed.
Take out the ink cartridge and put it in again
seating it properly.
10-23.)
The machine is out of paper.
Add paper, and then press Mono Start or
Colour Start.
The paper is jammed in the
machine.
No
The number you dialled does not
Verify the number and try again.
Response/Busy answer or is busy.
Not
Registered
You tried to access a One-Touch
or Speed-Dial number that is not
programmed.
Set up the One-Touch or Speed-Dial number.
5-2.)
10 - 2 TROUBLESHOOTING AND ROUTINE MAINTENANCE
ERROR MESSAGES
ERROR
CAUSE
ACTION
MESSAGE
Out of Memory The machine’s memory is full.
(Fax sending or copy operation in process)
Press Stop/Exit and wait until the other
operations in progress finish and then try again.
—OR—
Clear the data in the memory. To gain extra
memory, you can turn off Fax Storage. (See
—OR—
Print the faxes that are in the memory.
(Printing operation in process)
Reduce print resolution.
Paper Jam
Paper is jammed in the machine.
Unable to
Change
The machine has a mechanical
problem.
—OR—
A foreign obstacle, such as a clip
or ripped paper, is in the machine.
Close the document support and the document
tray. Open the top cover and remove any
foreign obstacles from inside the machine. If
the error message continues, please follow the
steps below before disconnecting the machine
so you will not lose any important messages.
Then, disconnect the machine from the power
source for several minutes (which will erase all
faxes), and then reconnect it.
Unable to
Clean
Unable to
Init.
Check whether the machine has faxes in the
memory
1. Press Menu/Set, 9, 0, 1.
Unable to
Print
2. If the machine has no faxes, disconnect the
machine from the power source for several
minutes, and then reconnect it.
Unable to
Scan
—OR—
If faxes are present, you can transfer them to
another fax machine. Go to Step 3.
Transfer faxes to another fax machine
If you have not set up your Station ID, you
cannot enter fax transfer mode.
3. Enter the fax number to which faxes will be
forwarded.
4. Press Mono Start.
5. After the faxes are transferred, disconnect
the machine from the power source for
several minutes, and then reconnect it.
You can transfer the Fax Journal report to
another fax machine by pressing Menu/Set,
9, 0, 2 in Step1.
Wrong Paper
Size
Paper is not the correct size.
Reload the correct size of paper (Letter, Legal
or A4), and then press Mono Start or
Colour Start.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 3
Paper is jammed inside the machine
1
Remove the jam clear cover. Pull the jammed paper out of the
machine.
Jam Clear Cover
2
3
Re-insert the jam clear cover.
If you can not pull out the jammed paper, close the document
support and the document tray and lift the open cover to the
open position until it locks securely into place.
4
Remove the jammed paper.
Top Cover
If the paper is jammed underneath the print head, disconnect
the machine from the power source so you can move the print
head to take out the paper.
10 - 6 TROUBLESHOOTING AND ROUTINE MAINTENANCE
5
Close the top cover.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 7
If you are having difficulty with your machine
If you think there is a problem with your machine, check the chart
below and follow the troubleshooting tips.
The Brother Solutions Center offers the latest FAQs and
troubleshooting tips.
DIFFICULTY
Printing
SUGGESTIONS
No printout
Check the interface cable connection on both the machine and your
computer.
Check the machine is plugged in and not in the Power Save condition.
Poor quality print.
Make sure the Printer Driver or Paper Type setting in the menu matches
the type of paper you are using. (See Media Type on page 1-8 in
Make sure your ink cartridges are fresh. Cartridges remain fresh for up
to two years if kept in their original packaging, after that the ink may
become clogged. Cartridge expiration dates are printed on the package.
1-9.)
The recommended environment for your machine is between 20°C to
33°C.
White horizontal lines appear
in text or graphics.
1-9.)
If horizontal bands appear when using plain paper, use the 'Enhanced
Normal Printing' mode to help avoid banding on some types of plain
paper. In the printer driver 'Basic' tab, click 'Settings', and check
'Enhanced Normal Printing'.
If you continue to have horizontal bands, change the Media Type
selection to 'Slow Drying Paper' in the printer driver 'Basic' tab to help
enhance the print quality.
The machine prints blank
pages.
Characters and lines are
stacked.
Printed text or images are
skewed.
Make sure the paper is loaded properly in the paper tray and the paper
10 - 8 TROUBLESHOOTING AND ROUTINE MAINTENANCE
DIFFICULTY
SUGGESTIONS
Printing (Continued)
Smudged stain at the top
center of the printed page.
Printing appears dirty or ink
seems to run.
on page 1-9.) Don’t handle the paper until the ink is dry.
Stains appear on the reverse
side or at the bottom of the
page.
There are some dense lines.
The printouts are wrinkled.
Check ‘Reverse Order’ in the Basic tab of the printer driver.
In the printer driver ‘Basic’ tab, click the ‘Settings’, and uncheck the
‘Bi-Directional Printing’.
Cannot perform ‘2 in 1 or 4 in 1’ Check that the paper size setting in the application and in the printer
printing.
driver are the same.
Print speed is too slow.
Changing the printer driver setting may improve the print speed.
Highest resolution needs longer data processing, transfer and printing
time. Try the other settings of quality in the printer driver ‘Basic’ tab.
Also, click the ‘Settings’ tab, and make sure you uncheck the Colour
Enhancement.
Borderless printing is slower than normal printing. If you want to print
more quickly, set the Borderless feature off. (See Media Type on page
1-8 in Software User’s Guide on the CD-ROM.)
Colour Enhancement is not
working properly.
If the image data is not full colour in your application (Such as 256
colour), Colour Enhancement will not work. Please use at least 24 bit
colour data with the Colour Enhancement feature.
Check that more than two types of paper are not loaded in the paper tray
at any one time.
neatly.
Machine does not print from
Paint Brush.
Try setting the Display setting to ‘256 colours.’
Machine does not print from
Adobe Illustrator.
Try to reduce the print resolution.
Printing Received Faxes
Condensed print and white
This can be caused by static or interference on the telephone line. You
streaks across the page or the can make a copy using the Mono Start key to see if the same problem
top and bottom of sentences
are cut off.
occurs. If the copy looks good then the problem is probably the phone
line and not your machine.
Vertical black lines when
receiving.
The sender’s scanner may be dirty. Ask the sender to make a copy to
see if the problem is with the sending machine. Try receiving from
another fax machine.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 9
DIFFICULTY
SUGGESTIONS
Printing Received Faxes (Continued)
Received colour fax prints only Replace the colour ink cartridges that are empty or nearly empty, and
in black and white.
off or a single page is printed
on two pages.
Phone Line or Connections
Dialling does not work.
(No dial tone)
Check the machine is plugged in.
Check for a dial tone. If possible, call your machine to hear it answer. If
there is still no answer, check the telephone line cord connection and
make sure all telephone connections are secured. If there is no ringing
when you call your machine, ask your telephone company to check the
line.
Receiving Faxes
Cannot receive a fax
Make sure the machine is in the correct receiving mode for your setup.
If you frequently encounter interference on the phone line, try changing
10-12.)
If you connect your machine to PBX, PABX or ADSL, set the menu
Sending Faxes
Cannot send a fax
Make sure that the Fax
Ask the other party to check that receiving machine has paper.
Print the Transmission Verification Report and check for an error.
Transmission Verification
Report says ‘Result:NG’ or
‘Result:ERROR’.
There is probably temporary noise or static on the line. Try sending the
fax again. If you send a PC FAX message and get ‘Result:NG’ on the
Transmission Verification Report, your machine may be out of memory.
If you frequently get transmission error with possible interference on the
phone line, try to change the menu setting of Compatibility to Basic.
If you connect your machine to PBX, PABX or ADSL, set the menu
Poor sending quality.
Try changing your resolution to Fineor S.Fine. Make a copy to check
your machine’s scanner operation.
Vertical black lines when
sending.
If the copy you made shows the same problem, your scanner is dirty.
10 - 10 TROUBLESHOOTING AND ROUTINE MAINTENANCE
DIFFICULTY
SUGGESTIONS
Handling Incoming Calls
The machine ‘Hears’ Voice as If your machine is set to Fax Detect ON, it is more sensitive to sounds.
CNG Tone.
Your machine may mistakenly interpret certain voices or music on the
line as a calling fax machine and respond with fax receiving tones.
Deactivate the fax by pressing Stop/Exit. Try avoiding this problem by
Transferring a Fax Call to the
machine.
If you answered at the machine, press Mono Start and hang up
immediately. If you answered on an external or extension phone, press
your Fax Receive Code (default setting is ( 51). When your machine
answers, hang up.
Custom features on a single
line.
If you have Call Waiting, Call Waiting/Caller ID, an alarm system or any
other custom feature on a single phone line with your machine, it may
create a problem sending or receiving faxes.
For example: If you are sending or receiving a fax message while a
custom feature signal comes through on the line, the signal can
temporarily interrupt or disrupt the faxes. Brother’s ECM feature should
help overcome this problem. This condition is related to the telephone
system industry and is common to all devices that send and receive data
on a single, shared line with custom features. If avoiding a slight
interruption is crucial to your business, we recommend a separate
phone line with no custom features.
Copying Difficulties
Cannot make a copy
Make sure that the Copy
Vertical streaks appear in
copies
Sometimes you may see vertical streaks on copies. Clean the scanner.
Scanning Difficulties (MFC-3240C only)
TWAIN/WIA errors appear
while scanning.
Make sure the Brother TWAIN/WIA driver is selected as the primary
source. In PaperPort®, click Scan in the File menu and select the
Brother TWAIN/WIA driver.
Software Difficulties (MFC-3240C only)
Cannot install software or print Run the MFL-Pro Suite Repair and Install program on the CD-ROM.
This program will repair and reinstall the software.
‘Device Busy’
Make sure the machine is not showing an error message on the LCD.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 11
Compatibility
If you are having difficulty sending or receiving a fax due to possible
interference on the phone line, we recommend that you adjust the
Equalization for compatibility. The machine adjusts the modem
speed for fax operations.
1
2
Press Menu/Set, 2, 0, 2.
Press ▲ or ▼ to select Basic, (or
Normal).
2.Compatibility
For MFC-3240C, you can select Highto return to 33600 bps.
Press Menu/Set.
3
Press Stop/Exit.
■ Basicreduces the modem speed to 9600 bps. Unless there
is a lot of interference on your phone line, you may prefer to
use it only when needed.
■ Normalsets the modem speed at 14400 bps.
10 - 12 TROUBLESHOOTING AND ROUTINE MAINTENANCE
How to improve print quality
Cleaning the print head
To ensure good print quality, the machine will regularly clean the
print head. You can start the cleaning process manually if needed.
Clean the print head and ink cartridges if you get a horizontal line in
the text or graphics on your printed pages. You can clean Black only
or three colours at a time (Cyan/Yellow/Magenta), or all four colours
at once.
Cleaning the print head consumes ink. Cleaning too often uses ink
unnecessarily.
Caution
Do NOT touch the print head. Touching the print head may cause
permanent damage and may void the print head’s warranty.
1
2
Press Ink Management.
Press ▲ or ▼ to select Cleaning.
Press Menu/Set.
3
Press ▲ or ▼ to select Black, Coloror All.
Press Menu/Set.
The machine will clean the print head. When cleaning is
finished, the machine will go back to standby mode
automatically.
■ If you clean the print head at least five times and the print
has not improved, call your Brother dealer for service.
■ The print head controls the flow of ink using tiny pumps to
produce characters or images onto the page.
■ We recommend having the machine powered up at all times.
The periodical cleaning is performed to prevent the drying up
of the ink in the head nozzles and is achieved by purging ink
from the print head. This process is performed automatically,
on average, every two days dependant on room
temperature. The machine is set so that this process occurs
in the early hours of the morning.
■ When the cleaning process is finished, the machine will
automatically return to its previous state.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 13
Checking the print quality
If faded or streaked colours and text appears on your output, some
of the nozzles may be clogged. You can check this by printing the
Print Quality Check Sheet and looking at the nozzle check pattern.
1
2
Press Ink Management.
Press ▲ or ▼ to select Test Print.
Press Menu/Set.
3
4
5
Press ▲ or ▼ to select Print Quality.
Press Menu/Set.
Press Colour Start.
The machine begins printing the Print Quality Check Sheet.
Check the sheet to see if the quality is OK by following these
steps:
Colour block quality check
The LCD shows:
Is Quality OK?
1.Yes 2.No
6
7
Check the quality of the four colour blocks on the sheet.
If all lines are clear and visible, press 1 (Yes), and go to Step 10.
—OR—
If you can see missing short lines as shown below, press 2 (No).
OK
Poor
The LCD will ask you if the print
quality is OK for black and three
colours.
Black OK?
1.Yes 2.No
10 - 14 TROUBLESHOOTING AND ROUTINE MAINTENANCE
8
9
Press 2 (No) for black or three
Start Cleaning?
1.Yes 2.No
colours with a problem.
The LCD shows:
Press 1 (Yes).
The machine will start cleaning the print head.
After cleaning is finished, press Colour Start. The machine will
start printing the Print Quality Check Sheet again and then
return to step 5.
10 Press Stop/Exit.
If you still see missing ink in this Print Quality Check Sheet, repeat
the cleaning and test print procedures at least five times. If ink is still
missing after the fifth cleaning and test print, replace the ink cartridge
for the clogged colour. (Perhaps the ink cartridge was in your
machine over six months or the expiration date written on the
cartridge package has passed. Or, the ink may not have been stored
properly before use.)
After replacing the ink cartridge, check it by printing another Print
Quality Check Sheet. If the problem still exists, repeat the cleaning
and test print procedures at least five times for the new ink cartridge.
If ink is still missing, call your Brother dealer.
Caution
Do NOT touch the print head. Touching the print head may cause
permanent damage and may void the print head’s warranty.
When a print head nozzle is
clogged the printed sample
looks like this.
After the print head nozzle is
cleaned, the horizontal lines
are gone.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 15
Checking the printing alignment
You should rarely need to adjust the printing alignment however, if
after transporting the machine your printed text becomes blurred or
images become faded then adjustment may need to be made.
1
2
Press Ink Management.
Press ▲ or ▼ to select Test Print.
Press Menu/Set.
3
4
Press ▲ or ▼ to select Alignment.
Press Menu/Set.
Press Mono Start or Colour Start.
The machine begins printing the Alignment Check Sheet.
The LCD shows:
Is Alignment OK?
1.Yes 2.No
5
Check the 600 dpi and 1200 dpi test prints to see if number 5
most closely matches number 0. If the number 5 sample of both
the 600 dpi and 1200 dpi are the best matches, press 1 (Yes) to
finish Alignment Check, and go to Step 8.
—OR—
If another test print number is a better match for either 600 dpi
or 1200 dpi, press 2 (No) to select it.
6
7
For 600 dpi, press the number of the
test print that most closely matches
the number 0 sample (1-8).
600dpi Adjust
Select Best # 5
For 1200 dpi, press the number of
the test print that most closely
matches the number 0 sample
1200dpi Adjust
Select Best # 5
(1-8).
8
Press Stop/Exit.
10 - 16 TROUBLESHOOTING AND ROUTINE MAINTENANCE
Checking the ink volume
You can check the ink that is left in the cartridge.
1
2
Press Ink Management.
Press ▲ or ▼ to select Ink Volume.
Press Menu/Set.
3
4
Press ▲ or ▼ to select the colour you
want to check.
Ink Volume
Bk:-
+
The LCD shows the ink volume.
Press Stop/Exit.
(MFC-3240C only) You can check the ink volume from your
computer. (See MFC Remote Setup (not available for
DCP-110C, DCP-310CN and MFC-210C) on page 4-1 in
Software User’s Guide on the CD-ROM or MFC Remote Setup
(Mac OS® X 10.2.4 or greater) (not available for DCP-110C,
DCP-310CN and MFC-210C) on page 8-43 in Software User’s
Guide on the CD-ROM.)
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 17
Packing and shipping the machine
Whenever you transport the machine, use the packing materials that
came with your machine. If you do not pack the machine properly,
you could void your warranty.
Caution
It is important to allow the machine to ‘park’ the print head after a
print job. Listen carefully to the machine before disconnecting it from
the power source to ensure that all mechanical noise has stopped.
Not allowing the machine to complete this parking process may lead
to print problems and possible damage to the print head.
1
2
Close the document support and the document tray.
Lift the top cover to the open position until it locks securely into
place.
3
Remove all the ink cartridges and attach the protective parts.
When attaching the protective parts, make sure it
clips into place as shown in the diagram.
Caution
If you are not able to find the protective parts, do NOT remove the ink
cartridges before shipping. It is essential that the machine be
shipped with either the protective parts or the ink cartridges in
position. Shipping without them will cause damage to your machine
and may void your warranty.
10 - 18 TROUBLESHOOTING AND ROUTINE MAINTENANCE
4
5
Close the top cover.
Unplug the machine from the telephone wall socket and remove
the telephone line cord from machine.
6
7
Unplug the machine from the electrical socket.
Unplug the USB cable or LAN cable from the machine, if it is
connected.
8
9
If your machine has a handset, remove it and the handset curled
cord.
Wrap the machine in the bag and place it in the original carton
with the original packing material.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 19
10 Pack the printed materials in the original carton as shown below.
Do not pack the used ink cartridges in the carton.
(FAX-1840C only)
(MFC-3240C only)
11 Close the carton.
10 - 20 TROUBLESHOOTING AND ROUTINE MAINTENANCE
Routine maintenance
Cleaning the Scanner
Unplug the machine, close the document support and the document
tray and then open the top cover. Clean the flat white plate and the
glass strip below the bar with isopropyl alcohol on a lint-free cloth.
White Plate
Glass Strip
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 21
Cleaning the machine Printer Platen
WARNING
■ Be sure to unplug the machine from the AC power outlet before
cleaning the printer platen.
■ Be careful not to touch the paper feed star wheels and encoder
film.
■ When you want to clean your machine printer platen, wipe it with
a lint free cloth that is dry.
■ If ink is scattered on or around the printer platen be sure to wipe
it off with a soft, dry, lint-free cloth.
Encoder Film
Paper Feed Star Wheel
Do NOT Touch!
Do NOT Touch!
Clean Here
10 - 22 TROUBLESHOOTING AND ROUTINE MAINTENANCE
Replacing the ink cartridges
Your machine is equipped with an ink dot counter. The ink dot
counter automatically monitors the level of ink in each of the 4
cartridges. When the machine detects an ink cartridge is running out
of ink, the machine will notify you with a message on the LCD.
The LCD will inform you which ink cartridge is low or needs replacing.
Be sure to follow the LCD prompts to replace the ink cartridges in the
correct order.
Even though the machine informs you that an ink cartridge is empty,
there will be a small amount of ink remaining in the ink cartridge. It is
necessary to keep some ink in the ink cartridge to prevent air from
drying out and damaging the print head assembly.
1
2
Close the document support and the document tray.
Lift the top cover to the open position until it locks securely into
place.
If one or more ink cartridges are empty, for example Black, the
LCD shows Ink Empty Blackand Open Cover.
3
Pull the ink cartridge hook toward you and remove the ink
cartridge for the colour shown on the LCD.
Ink Cartridge Hook
4
Open the new ink cartridge bag for the colour shown on the
LCD, and then take out the ink cartridge.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 23
5
Remove the cartridge covers.
Cartridge Cover
DO NOT TOUCH
Do not touch the area shown in the illustration above.
If the cartridge cover comes off when you open the bag the
cartridge will not be damaged.
6
Each colour has its own correct position. Keep the ink cartridge
in an upright position when you insert it into slot. Press down on
the ink cartridge until the hook snaps over it.
New Ink Cartridge
Ink Cartridge Hook
10 - 24 TROUBLESHOOTING AND ROUTINE MAINTENANCE
7
If you replaced an ink cartridge while Near Emptywas
displayed on the LCD, the LCD may ask you to verify that it was
a brand new one. Example: Did You ChangeBlck? 1.Yes
2.No. For each new cartridge you installed, press 1 on the dial
pad to automatically reset the ink dot counter for that colour. If
the ink cartridge you installed is not a brand new one, please be
sure to select 2.
If you wait until Ink Emptymessage is displayed on the LCD,
the machine will automatically reset the ink dot counter.
If the Installmessage is on the display after you have
installed ink cartridges, check that the ink cartridges are
installed properly.
WARNING
If ink gets in your eyes, irrigate them with water immediately and call
a doctor if you are concerned.
TROUBLESHOOTING AND ROUTINE MAINTENANCE 10 - 25
Caution
■ Do not remove ink cartridges if you do not need to replace them.
If you do so, it may reduce the ink quantity and the machine will
not know the quantity of ink left in the cartridge.
■ Do not touch the cartridge insertion slots. If you do so, the ink
may stain your skin.
■ If ink stains your skin or clothing, wash with soap or detergent
immediately.
■ If you install an ink cartridge in the wrong colour position, you
must clean the print head several times before you start printing
(after correcting the cartridge installation) because the colours
were mixed.
■ Once you open an ink cartridge, install it in the machine and use
it up within six months of installation. Use unopened ink
cartridges by the expiration date written on the cartridge
package.
■ Do not dismantle or tamper with the ink cartridge, this can cause
the ink to leak out of the cartridge.
■ Brother multifunction machines are designed to work with ink of
a particular specification and work to a level of optimum
performance when used with genuine Brother ink cartridges.
Brother cannot guarantee this optimum performance if ink or ink
cartridges of other specifications are used. Brother does not
therefore recommend the use of cartridges other than genuine
Brother cartridges with this machine or the refilling of empty
cartridges with ink from other sources. If damage is caused to the
print head or other parts of this machine as a result of the use of
ink or ink cartridges other than genuine Brother products due to
the incompatibility or lack of suitability of those products with this
machine, any repairs required as a result will not be covered by
the warranty.
10 - 26 TROUBLESHOOTING AND ROUTINE MAINTENANCE
Appendix A
A
Telephone Service for Australia
Telstra® FaxStream® Duet® (Distinctive Ringing)
Telstra® FaxStream® Duet® is an enhanced Public Switched
Telephone Service (PSTS) offered by Telstra® that allows you to
have an additional number on one phone line, with its own distinctive
ring pattern. Telstra® FaxStream® Duet® is a call handling feature
that helps users distinguish voice and facsimile calls. With
FaxStream® Duet®, incoming calls to a fax number are announced
by a different, distinctive ring signal. Only one call can be answered
(or made) at any one time and while this call is in progress, incoming
calls to either number will be presented with a busy tone.
Your MFC has a Distinctive Ringing function, allowing you to
dedicate one phone number just for receiving faxes.
After you have set the Distinctive Ring feature to On, the receive
mode is set to Manualautomatically. Unless you have a TAD or
Voice Mail set up on the Distinctive Ring number, Manualmode
means you must answer all the calls yourself. You can not
change the receive mode to the other mode while the Distinctive
Ring is set to on.
What is the Advantage of using Telstra® FaxStream® Duet®
Function?
Using Telstra® FaxStream® Duet® is the most efficient way to receive
both fax and telephone calls on the same line. When the voice call
comes in, all phones (extension and external) and the fax machine
will ring to alert you to pick it up. If a fax call comes in, the fax
machine will answer automatically without ringing, whereas the
extension and external phones will ring with a distinctive ring pattern.
It is also a more efficient way of operating a Fax machine with an
extension phone as you do not have to use the remote activation
codes. It gives you two independent numbers without the higher cost
of a second line.
APPENDIX A A - 1
How does Telstra® FaxStream® Duet® Work?
Incoming calls to the voice number, will have the standard ring
pattern of long, long tone, followed by a pause, repeated, while the
new fax number will have a different ring pattern of three short bursts
of ring, repeated at regular intervals.
When FaxStream® Duet® is Onand you receive a voice call all
extension and external phones will ring with a standard ring pattern.
The fax machine will ring on the third ring with a standard ring
pattern. All external and the extension phones will continue to ring.
Either you or a telephone answering device can answer the voice
number.
When FaxStream® Duet® is Onand you receive a fax call on the
Duet® number the Fax machine will answer and automatically
receive the fax message without ringing. On the other hand, all
extension and external phones will ring with a distinctive ring pattern.
Do not answer the phone as you are receiving a fax message.
Flowchart Sequence of Incoming call
Incoming Call
(either Voice or Fax)
All extension phones ring,
fax machine is silent.
Registered
Main number (Voice Number)
Duet (Fax) Number
Fax machine automatically
receives and prints fax
message without ringing.
Fax machine begins
ringing on third ring.
Telephone Answering
Device (TAD)
answers the call.
You answer the call
at an external phone
or an extension
phone.
A - 2 APPENDIX A
Set the Distinctive Ringing to ON
1
Disconnect the fax machine from any TAD or telephone
company voice mail.
2
Press Menu/Set, 2, 0, 3.
The screen displays the current
setting of this feature.
3.Distinctive
3
4
5
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
Press Stop/Exit.
Caller ID (Caller IDentification)
Caller ID is a telephone service that allows the subscriber to see a
display of the caller’s phone number or name as the telephone rings.
It is a fast way to screen your calls. You can respond quickly to calls
you missed, because Caller IDs are received and stored in your MFC
memory.
To get the Caller ID Service: apply for the Caller ID service at
your local telephone company, if available.
Advantages of Caller ID
For Business
All businesses profit from a quicker response to customer calls.
Businesses that provide mail order services, money-lending services
or provide confidential information, can protect themselves from
false orders or acceptance of false identification.
At Home
Residential customers can protect themselves from unwanted calls.
APPENDIX A A - 3
How Does the Caller ID Work?
The Caller ID Appears on the Display When Your
Telephone Rings
As your telephone rings, the display shows you the caller’s phone
number or name if the name has stored in the One-Touch and
Speed-Dial. Once you pick up the handset, the caller’s ID
disappears. You will see up to the first 16 characters of the number
on the display.
■ If Out of Areaappears on the display, it means that the
call came from outside your caller ID service area or a public
phone. *
■ If Private Callappears on the display, it means the caller
intentionally blocked the transmission of his/her ID. *
* Depends on network Function.
The Caller ID is Stored in Your MFC Memory
The MFC can store a maximum of the last 30 incoming caller IDs in
the memory, along with the time and date of reception. The 31st call
will cause the oldest ID to be erased.
The Caller ID information stored in the memory can be used for the
following.
■ Printing the Caller ID List.
You can review calls you received by checking the Caller IDs in
memory. This report will list the Date, Time, Phone Number
(Caller ID) name, and type of Call (Comment) if available.
A - 4 APPENDIX A
Viewing Caller ID List
Caller ID memory stores information for up to thirty calls; when the
thirty-first call comes in, information about the first call is erased. You
can scroll through Caller ID information to review those calls made to
your MFC.
1
2
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Display#
and press Menu/Set.
4.Caller ID
If the name was not received, it will not be displayed.
3
Press ▲ or ▼ to scroll through the Caller ID memory to select the
Caller ID you want to view and press Menu/Set.
The next screen shows the caller’s telephone number and the
date and time of the call.
4
Press Stop/Exit to exit.
Printing Caller ID List
1
2
3
4
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Print Report.
Press Menu/Set.
Press Start.
APPENDIX A A - 5
Telephone Service for New Zealand
FaxAbility
FaxAbility is a service offered by Telecom that allows you to have an
additional number on one phone line, with its own distinctive ring
pattern. This way, when you get an incoming call, you can identify the
number being called by its ring.
How Will the Fax Machine Treat All Other Numbers?
FaxAbility mode ensures that the machine will answer calls to the
FaxAbility (secondary) number. When a call comes in to your main
number, all the phones will ring. You can set an external answering
device (TAD) to answer calls on the other number(s). (See the chart
in the following page.)
What is the Advantage of Using the FaxAbility Function?
Using FaxAbility is the most efficient way to receive both fax and
telephone calls on the same line. It is much easier for your callers
who dial manually. The fax machine will answer with receiving tones
so they will not have to press an activation code. And the people who
call to talk on your main number will not have to talk to your fax
machine. Basically, it gives you two independent numbers without
the higher cost of a second line.
A - 6 APPENDIX A
How Does FaxAbility Work?
Your telephone number will have the standard ring pattern of long,
long tone, while the new number will have a ring pattern of long,
silence, long, etc. When FaxAbility is On, you will not hear the first
ring of all incoming calls on the fax machine. Extension phones will
ring as usual. If the fax machine recognizes the ring pattern, all
ringing will stop and the fax machine will answer and automatically
receive the fax message. Otherwise, you will hear the extension
phones and the fax machine continue to ring. The fax machine
always listens to the ring pattern before it answers, so do not pick up
the phone during that time. You will quickly learn to recognize the
ring pattern for faxes, so you will not be tempted to answer that
number. Either you or a telephone answering device can answer the
main number(s).
Flowchart Sequence of Incoming call
Incoming Call
(either Voice or Fax)
All extension phones ring,
fax machine is silent.
Registered
Main number (Voice Number)
Duet (Fax) Number
Fax machine automatically
receives and prints fax
message without ringing.
Fax machine begins
ringing on third ring.
Telephone Answering
Device (TAD)
answers the call.
You answer the call
at an external phone
or an extension
phone.
After you have set the FaxAbility feature to On, the receive mode
is set to Manualautomatically. Unless you have a TAD or Voice
Mail set up on the FaxAbility number, Manual mode means you
must answer all the call yourself. You can not change the
receive mode to the other mode while the FaxAbility is set to on.
APPENDIX A A - 7
How to Turn FaxAbility OFF or ON
The FaxAbility function is designed to accommodate the FaxAbility
service provided by Telecom. To change the setting, repeat Steps
1-3; Step 2 is where you can select either Onor Off.
Call Waiting beeps caused by incoming calls on your main number
can affect fax transmissions. If you have FaxAbility Service but don’t
have Call Waiting, you need do nothing at this stage. If you do have
Call Waiting as well as FaxAbility, set the Call Waiting menu option
to On. See below.
1
Press Menu/Set, 2, 0, 3.
The screen displays
3.Faxability
2
Press ▲ or ▼ to set FaxAbility to Onor Off.
If you have FaxAbility service, select On.
Press Menu/Set.
Press ▲ or ▼ to set Call Waiting to Onor Off. If you have Call
Waiting service, select Onto avoid the trouble caused by Call
Waiting.
3
4
5
6
Press Menu/Set.
Press Stop/Exit.
A - 8 APPENDIX A
Caller ID (Caller IDentification)
Caller ID is a telephone service that allows the subscriber to see a
display of the caller’s phone number and name if available as the
telephone rings. It is a fast way to screen your calls. You can respond
quickly to calls you missed, because Caller IDs are received and
stored in your MFC memory.
To get the Caller ID Service: apply for the Caller ID service at
your local telephone company, if available.
Advantages of Caller ID
For Business
All businesses profit from a quicker response to customer calls.
Businesses that provide mail order services, money-lending services
or provide confidential information, can protect themselves from
false orders or acceptance of false identification.
At Home
Residential customers can protect themselves from unwanted calls.
How Does the Caller ID Work?
The Caller ID Appears on the Display When Your
Telephone Rings
As your telephone rings, the display shows you the caller’s phone
number and name if available. Once you pick up the handset, the
caller’s ID disappears. You will see up to the first 16 characters of the
number and name if available on the display.
■ If Out of Areaappears on the display, it means that the
call came from outside your caller ID service area. *
■ If Private Callappears on the display, it means the caller
intentionally blocked the transmission of his/her ID. *
* Depends on network Function.
APPENDIX A A - 9
Viewing Caller ID List
Caller ID memory stores information for up to thirty calls; when the
thirty-first call comes in, information about the first call is erased. You
can scroll through Caller ID information to review those calls made to
your MFC.
1
2
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Display#
and press Menu/Set.
4.Caller ID
If the name was not received, it will not be displayed.
3
Press ▲ or ▼ to scroll through the Caller ID memory to select the
Caller ID you want to view and press Menu/Set.
The next screen shows the caller’s telephone number and the
date and time of the call.
4
Press Stop/Exit.
Printing Caller ID List
1
2
3
4
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Print Report.
Press Menu/Set.
Press Start.
If you use the Caller ID for Dial back…
■ Please be sure that you use appropriate dialling procedures
for local and national call.
■ Please be sure that you make sure of the details of the exact
number to be called back, and the need to insert prefix(es)
for manual dialling.
■ Please understand that your MFC may not display precisely
the digits to be called.
A - 10 APPENDIX A
Telephone Service for Some Countries
Distinctive Ringing
(For Singapore and Hong Kong)
This MFC feature lets you use the Distinctive Ringing subscriber
service offered by some telephone companies, which allows you to
have several telephone numbers on one phone line. Each phone
number has its own Distinctive Ringing pattern, so you will know
which phone number is ringing. This is one way you can have a
separate phone number for your MFC.
Your MFC has a Distinctive Ringing function, allowing you to
dedicate one phone number just for receiving faxes. You will need to
set Distinctive Ringing to On.
You can switch it off temporarily, then turn it back on. When you
get a new fax number, make sure you reset this function.
■ The MFC will answer only calls to the Distinctive Ringing
number.
After you have set the Distinctive Ring feature to On, the receive
mode is set to Manualautomatically. Unless you have a TAD or
Voice Mail set up on the Distinctive Ring number, Manualmode
means you must answer all the call yourself. You can not
change the receive mode to the other mode while the Distinctive
Ring is set to on.
Setting the Distinctive Ringing
1
2
3
4
Press Menu/Set, 2, 0, 3.
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
3.Distinctive
Press Stop/Exit.
APPENDIX A A - 11
Caller ID (For Singapore and Hong Kong)
The Caller ID feature of this MFC lets you use the Caller ID
subscriber service offered by many local phone companies. This
service provides you, by means of the screen display, the telephone
After a few rings, the screen displays the telephone number of your
caller (or name, if available). Once you pick up the handset, the
Caller ID information disappears from the screen, but the call
information remains stored in the Caller ID memory.
■ You will see the first 16 characters of the number or name.
■ Out of Areadisplay means call originates outside your Caller
ID service area.
■ Private Calldisplay means the caller has intentionally
blocked transmission of information.
You can print a list of Caller ID information received by your
MFC.
Caller ID service varies with different carriers. Call your local
phone company to determine the kind of service available in
your area.
A - 12 APPENDIX A
Viewing Caller ID List
Caller ID memory stores information for up to thirty calls; when the
thirty-first call comes in, information about the first call is erased. You
can scroll through Caller ID information to review those calls made to
your machine.
1
2
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Display#
and press Menu/Set.
4.Caller ID
If the name was not received, it will not be displayed.
3
Press ▲ or ▼ to scroll through the Caller ID memory to select the
Caller ID you want to view and press Menu/Set.
The next screen shows the caller’s telephone number and the
date and time of the call.
4
Press Stop/Exit.
Printing Caller ID List
1
2
3
Press Menu/Set, 2, 0, 4.
Press ▲ or ▼ to select Print Reportand press Menu/Set.
Press Start.
APPENDIX A A - 13
Advanced receiving operations
Operation from extension telephones
If you answer a fax call on an extension telephone, or an external
telephone into the correct socket on the machine, you can make your
machine take the call by using the Fax Receive Code. When you
press the Fax Receive Code 51 ( 91 for New Zealand), the
If the machine answers a voice call and pseudo/double-rings for you
to take over, use the Telephone Answer Code #51 (#91 for New
If you answer a call and no one is on the line, you should assume that
you’re receiving a manual fax.
■ Press 51 ( 91 for New Zealand) and wait for the chirp or until
the machine’s LCD displays Receiving, and then hang up.
Your caller will have to press Start to send the fax.
A - 14 APPENDIX A
Fax/Tel mode
When the machine is in Fax/Tel mode, it will use the F/T Ring Time
(pseudo/double-ringing) to alert you to pick up a voice call.
If you are at an extension phone, you’ll need to lift the handset during
the F/T Ring Time and then press #51 (#91 for New Zealand)
between the pseudo/double rings. If no one is on the line, or if
someone wants to send you a fax, send the call back to the machine
by pressing 51 ( 91 for New Zealand).
Fax/Tel mode in the Power Save condition
For FAX-1840C:
When the machine is in Fax/Tel mode and pseudo/double-rings to
alert you to pick up a voice call, you can only answer by picking up
the machine’s handset.
If you answer before the machine answers with
pseudo/double-ringing, you can pick up the call at an external or
extension phone.
For MFC-3240C:
Fax/Tel mode does not work in the power save condition. The
machine will not answer telephone or fax calls and will keep ringing.
If you are at an external or extension phone, lift the handset of the
extension phone and talk. If you hear fax tones, hold the handset
until Fax Detect activates your machine. If the other party says they
want to send you a fax, activate the machine by pressing 51 ( 91
for New Zealand).
APPENDIX A A - 15
Using a cordless external handset
If the base unit of your cordless telephone is connected (see page
A-17) and you typically carry the cordless handset elsewhere, it is
easier to answer calls during the Ring Delay.
Not all brands of cordless phones are compatible for use with
your MFC.
Changing the remote codes
Remote Codes might not work with some telephone systems. The
preset Fax Receive Code is 51 ( 91 for New Zealand). The
preset Telephone Answer Code is #51 (#91 for New Zealand).
If you are always disconnected when accessing your external
TAD remotely, try changing the Fax Receive Code and
Telephone Answer Code to another three-digit code (such as
### and 999).
1
2
3
If it is not illuminated in green, press
Press Menu/Set, 2, 1, 4.
Press ▲ or ▼ to select On(or Off).
Press Menu/Set.
(Fax).
4.Remote Code
4
5
6
Enter the new Fax Receive Code.
Press Menu/Set.
Enter the new Telephone Answer Code.
Press Menu/Set.
Press Stop/Exit.
A - 16 APPENDIX A
Connecting an external device to your
machine
Connecting an external telephone
You can connect a separate telephone as shown in the diagram
below.
Extension
Telephone
External
Telephone
When you are using external or extension telephone, the LCD shows
Telephone(MFC-3240C only) or Ext. Tel in Use(FAX-1840C
only).
APPENDIX A A - 17
Connecting an external telephone answering
device (TAD)
Sequence
You may choose to connect an additional answering device.
However, when you have an external TAD on the same telephone
line as the machine, the TAD answers all calls and the machine
“listens” for fax calling (CNG) tones. If it hears them, the machine
takes over the call and receives the fax. If it does not hear CNG
tones, the machine lets the TAD continue playing your outgoing
message so your caller can leave you a voice message.
The TAD must answer within four rings (the recommended setting is
two rings). The machine cannot hear CNG tones until the TAD has
answered the call, and with four rings there are only 8 to 10 seconds
of CNG tones left for the fax “handshake”. Make sure you carefully
follow the instructions in this guide for recording your outgoing
message. We do not recommend using the toll saver feature on your
external answering machine if it exceeds five rings.
If you do not receive all your faxes, reduce the Ring Delay
setting on your external TAD to one or two rings.
A - 18 APPENDIX A
Do not connect a TAD elsewhere on the same phone line.
TAD
TAD
When you are using a TAD, the LCD shows Telephone
(MFC-3240C only) or Ext. Tel in Use(FAX-1840C only).
Connections
The external TAD must be connected as shown above.
1
Set your external TAD to one or two rings. (The machine’s Ring
Delay setting does not apply.)
2
3
4
Record the outgoing message on your external TAD.
Set the TAD to answer calls.
Set the Receive Mode to External TAD.
APPENDIX A A - 19
Recording outgoing message (OGM) on an external TAD
Timing is important in recording this message. The message sets up
the ways to handle both manual and automatic fax reception.
1
Record 5 seconds of silence at the beginning of your message.
(This allows your machine time to listen for the fax CNG tones
of automatic transmissions before they stop.)
2
Limit your speaking to 20 seconds.
We recommend beginning your OGM with an initial 5-second
silence because the machine cannot hear fax tones over a
resonant or loud voice. You may try omitting this pause, but if your
machine has trouble receiving, then you must re-record the OGM
to include it.
A - 20 APPENDIX A
Multi-line connections (PBX)
(For Australia and New Zealand only)
Most offices use a central telephone system. While it is often
relatively simple to connect the machine to a key system or a PBX
(Private Branch Exchange), we suggest that you contact the
company that installed your telephone system and ask them to
connect the machine for you. It is advisable to have a separate line
for the machine.
If the machine is to be connected to a multi-line system, ask your
installer to connect the unit to the last line on the system. This
prevents the unit from being activated each time a telephone call is
received.
If you are installing the machine to work with a PBX
1
It is not guaranteed that the unit will operate properly under all
circumstances with a PBX. Any cases of difficulty should be
reported first to the company that handles your PBX.
2
If all incoming calls will be answered by a switchboard operator,
it is recommended that the Receive Mode be set to Manual. All
incoming calls should initially be regarded as telephone calls.
Custom features on your phone line
If you have Voice Mail, Call Waiting, Call Waiting/Caller ID,
RingMaster, an answering service, an alarm system EFTPOS,
PC/FAX modem or other custom feature on one phone line it may
APPENDIX A A - 21
Appendix B
B
On-screen programming
Your machine is designed to be easy to use with LCD on-screen
programming using the navigation keys. User-friendly programming
helps you take full advantage of all the menu selections your
machine has to offer.
Since your programming is done on the LCD, we have created
step-by-step on-screen instructions to help you program your
machine. All you need to do is follow the instructions as they guide
you through the menu selections and programming options.
Menu table
You can probably program your machine without the User’s Guide if
help you understand the menu selections and options that are found
in the machine’s programs.
You can program your machine by pressing Menu/Set,
followed by the menu numbers.
For example to set Fax Resolutionto Fine:
Press Menu/Set, 2, 2, 2 and ▲ or ▼ to select Fine.
Press Menu/Set.
Memory storage
If there is a power failure, you will not lose your menu settings
because they are stored permanently. Temporary settings (such as
Contrast, Overseas Mode, and so on) will be lost. You may also have
to reset the date and time.
B - 1 APPENDIX B
Navigation keys
Access the menu
Go to the next menu level
Accept an option
Scroll through the current
menu level
Go back to the previous
menu level
Exit the menu
You can access the menu mode by pressing Menu/Set.
When you enter the menu, the LCD scrolls.
Press 1 for General Setup menu
1.General Setup
—OR—
Press 2 for Fax menu
—OR—
2.Fax
Press 3 for Copy menu
3.Copy
Press 0 for Initial Setup
0.Initial Setup
You can scroll more quickly through each menu level by pressing the
arrow for the direction you want: ▲ or ▼.
Select an option by pressing Menu/Set when that option appears on
the LCD.
The LCD will then show the next menu level.
Press ▲ or ▼ to scroll to your next menu selection.
Press Menu/Set.
When you finish setting an option, the LCD shows Accepted.
APPENDIX B B - 2
to
to
accept
exit
Select & Set
Select & Set
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Sets the time to
Page
1.General
1.Mode Timer
—
5 Mins
2-4
Setup
return to Fax mode.
2 Mins
1 Min
30 Secs
(Default for
MFC-3240C)
0 Sec
(Default for
FAX-1840C)
Off
2.Paper Type
—
—
Plain
Inkjet
Sets the type of
paper in the paper
tray.
2-6
2-6
Glossy
Transprncy
3.Paper Size
Letter
Legal
A4
Sets the size of the
paper in the paper
tray.
A5
10x15cm
4.Volume
1.Ring
2.Beeper
3.Speaker
—
High
Med
Low
Off
Adjusts the ring
volume.
2-7
2-7
2-8
High
Med
Low
Off
Adjusts the volume
level of the beeper.
High
Med
Low
Off
Adjusts the speaker
volume.
5.Auto
Daylight
On
Changes for Daylight 2-8
Savings Time
Off
automatically.
The factory settings are shown in Bold.
B - 3 APPENDIX B
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Page
1.General
Setup
6.P.Save
Setting
—
On
Off
Customizes the
Power Save key not
to receive fax in
power save
1-6
(Continued)
condition.
7.LCD
Contrast
—
Light
Adjust the contrast of 2-8
the LCD.
Dark
2.Fax
1.Setup
Receive
1.Ring Delay 02-10(02)
(Example for
Sets the number of
rings before the
machine answers in
Fax Only or Fax/Tel
mode.
4-2
(In Fax mode
only)
Australia)
2.F/T Ring
70 Sec
Sets the
4-3
Time
pseudo/double-ring
time in Fax/Tel
mode.
40 Sec
30 Sec
20 Sec
(Example for
Australia)
3.Fax Detect On
Semi
Receives fax
messages without
pressing the
Mono Start or
Colour Start key.
4-4
(FAX-1840C
only)
Off
4.Remote
Code
On
You can answer all
calls at an extension
or external phone
and use codesto turn
the machine on or off.
You can personalize
these codes.
A-16
(
(
51, #51)
91, #91 for
New Zealand)
Off
5.Auto
Reduction
On
Off
Reduces the size of
incoming faxes.
4-6
4-7
6.Memory
Receive
On
Off
Automatically stores
any incoming faxes
in its memory if it runs
out of paper.
7.Polling RX Standard
Secure
Sets up your
machine to poll
another fax machine.
4-8
Timer
The factory settings are shown in Bold.
APPENDIX B B - 4
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Page
2.Fax
(Continued)
2.Setup Send 1.Contrast
(In Fax mode
only)
Auto
Light
Dark
Changes the
lightness or darkness
of faxes you send.
3-6
2.Fax
Resolution
Standard
Fine
Sets the default
resolution for
3-7
outgoing faxes.
S.Fine
Photo
3.Delayed
Fax
—
Set the time of day in 3-13
24 hour format that
the delayed faxes will
be sent.
4.Batch TX
On
Combines delayed
faxes to the same fax
number at the same
time of day into one
transmission.
3-14
Off
5.Real Time
TX
Off
You can send a fax
without using the
memory.
3-9
On
Next Fax
Only
6.Polled TX
Standard
Secure
Setsup thedocument 3-15
on your machine to
be retrieved by
another fax machine.
7.Overseas
Mode
On
If you are having
difficultly sending
faxes overseas, set
this to On.
3-12
5-1
5-2
5-4
Off
3.Set
Quick-Dial
1.One-Touch
Dial
Stores One-Touch
Dial numbers, so you
can dial by pressing
one key (and Start).
2.Speed-Dial
—
—
Stores Speed-Dial
numbers, so you can
dialbypressingonlya
few keys (and Start).
3.Setup
Groups
Sets up a Group
number for
Broadcasting.
The factory settings are shown in Bold.
B - 5 APPENDIX B
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Page
2.Fax
(Continued)
4.Report
Setting
1.Transmission On
On+Image
Initial setup for
Transmission
Verification Report
and Journal Report.
7-1
Off
Off+Image
2.Journal
Every 7 Days
7-2
Period
Every 2 Days
Every 24
Hours
Every 12
Hours
Every 6
Hours
Every 50
Faxes
Off
5.RemoteFax 1.Forward/
Off
Sets the machine to
forward fax messages,
to store incoming faxes
in the memory (so you
can retrieve themwhile
youareawayfromyour
machine).
6-2
6-3
Opt
Store
Fax Forward
Fax Storage
2.Remote
Access
---
You must set your
own code for Remote
Retrieval.
3.Print
Document
—
—
stored in the memory.
6.Remaining
Jobs
—
Checkswhich jobs arein 3-10
the memoryand lets you
cancel selected jobs.
0.Miscellaneous 1.TX Lock
(1.Key Lock)
—
Prohibitsmostfunctions 3-17
except receiving faxes.
2.Compatibility High
(MFC-3240C only)
Adjust the
10-12
Equalization for
transmission
problems.
Normal
Basic
3
.Distinctive On
distincive ringing service
toregistertheringpattern
with the machine.
(Notavailablein Off
New Zealand)
A-11
3
.
Faxability On
If you have FaxAbility
from Telecom, you can
use this function to
storetheringingpattern
of your fax number.
A-6
(For New
Zealand Only)
Off
And if you set in to ON,
you should use the
registerednumber only.
4.Caller ID
Display#
Print Report
View or print a list of
the last 30 Caller IDs
stored in memory.
The factory settings are shown in Bold.
APPENDIX B B - 6
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Page
3.Copy
1.Quality
—
Best
Selects the Copy
resolution for your
type of document.
8-12
Normal
Fast
2.Brightness
—
-
-
-
-
-
+
+
+
+
+
Adjusts the
brightness.
8-12
8-13
8-13
3.Contrast
—
-
-
-
-
-
+
+
+
+
+
Adjusts the contrast
for copies.
4.Color
Adjust
1.Red
2.Green
3.Blue
R:-
R:-
R:-
R:-
R:-
+
Adjusts the amount
of Red in copies.
+
+
+
+
G:-
G:-
G:-
G:-
G:-
+
+
+
+
+
Adjusts the amount
of Green in copies.
B:-
B:-
B:-
B:-
B:-
+
+
+
+
+
Adjusts the amount
of Blue in copies.
4.Print
Reports
(MFC-3240C
only)
1.Help List
—
—
—
—
—
—
You can print these
lists and reports.
7-3
2.Quick-Dial
3.Fax
Journal
4.XMIT
—
—
Verify
The factory settings are shown in Bold.
B - 7 APPENDIX B
Main Menu
Submenu
Menu
Selections
Options
Descriptions
Page
0.Initial
Setup
1.Receive
Mode
—
Fax Only
Fax/Tel
You can choose the
receive mode that
best suits your
needs.
4-2
External
TAD
Manual
2.Date/Time
—
—
—
Puts the date and
time on the LCD and
in headings of faxes
you send.
2-1
2-2
2-1
3.Station ID
Fax:
Program your name
and fax number to
appear on each page
you fax.
Name:
4.Tone/Pulse
(Not available in
New Zealand)
—
—
Tone
Pulse
Selects the dialling
mode.
5.Phone Line
Set
PBX
Select the phone line 2-3
type.
(For Australia
and New
Zealand only)
ADSL
Normal
The factory settings are shown in Bold.
APPENDIX B B - 8
Entering Text
When you are setting certain menu selections, such as the Station
ID, you may need to type text into the machine. Most number keys
have three or four letters printed above them. The keys for 0, # and
do not have printed letters because they are used for special
characters.
By pressing the appropriate number key repeatedly, you can access
the character you want.
Press Key
one time
two times
three times
four times
2
3
4
5
6
7
8
9
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
L
M
P
T
O
R
V
Y
W
Inserting spaces
To enter a space in the fax number, press
numbers. To enter a space in the name, press
characters.
once between
twice between
Making corrections
If you entered a letter incorrectly and want to change it, press
move the cursor under the incorrect character. Then press
Stop/Exit. All letters above and to the right of the cursor will be
to
deleted. Re-enter the correct character. You can also back up and
type over incorrect letters.
Repeating letters
If you need to enter a character that is on the same key as the
previous character, press
you press the key again.
to move the cursor to the right before
B - 9 APPENDIX B
Glossary
G
ADF (automatic document feeder) Documents can be placed in
the ADF and scanned one page at a time automatically.
Auto Reduction Reduces the size of incoming faxes.
Automatic fax transmission (MFC-3240C only) Sending a fax
without picking up the handset of an external phone.
Automatic fax transmission (FAX-1840C only) Sending a fax
without picking up the handset of the machine.
Automatic Redial A feature that enables your machine to redial the
last fax number after five minutes if the fax did not go through
because the line was busy.
Backup Print Your machine prints a copy of every fax that is
received and stored in memory.This is a safety feature so you will
not lose messages during a power failure.
Batch Transmission (Black and white faxes only) As a cost saving
feature, all delayed faxes to the same fax number will be sent as
one transmission.
Beeper Volume Volume setting for the beep when you press a key
or make an error.
Brightness Changing the Brightness makes the whole image
lighter or darker.
Broadcasting The ability to send the same fax message to more
than one location.
Cancel Job Cancels a programmed job, like Delayed Fax or Polling.
CNG tones The special tones (beeps) sent by fax machines during
automatic transmission to tell the receiving machine that a fax
machine is calling.
Coding method Method of coding the information contained in the
document. All fax machines must use a minimum standard of
Modified Huffman (MH). Your machine is capable of greater
compression methods, Modified Read (MR), Modified Modified
Read (MMR) and JPEG, if the receiving machine has the same
capability.
G - 1 GLOSSARY
Communication error (or Comm. Error) An error during fax
sending or receiving, usually caused by line noise or static.
Compatibility group The ability of one fax unit to communicate
with another. Compatibility is assured between ITU-T Groups.
Contrast Setting to compensate for dark or light documents, by
making faxes or copies of dark documents lighter and light
documents darker.
Delayed Fax Sends your fax at a specified later time that day.
Distinctive Ring A subscriber service purchased from the
telephone company that gives you another phone number on an
existing phone line. The Brother machine uses the new number to
simulate a dedicated fax line.
Dual Access Your machine can scan outgoing faxes or scheduled
jobs into memory at the same time it is sending a fax or receiving
or printing an incoming fax.
ECM (Error Correction Mode) Detects errors during fax
transmission and resends the pages of the fax that had an error.
Extension phone A telephone on the fax number that is plugged
into a separate wall socket.
External phone A TAD (telephone answering device) or telephone
that is connected to your machine.
F/T Ring Time The length of time that the Brother machine rings
(when the Receive Mode setting is Fax/Tel) to notify you to pick
up a voice call that it answered.
Fax Detect Enables your machine to respond to CNG tones if you
interrupt a fax call by answering it.
Fax Forwarding Sends a fax received into the memory to another
pre-programmed fax number.
Fax Journal Lists information about the last 200 incoming and
outgoing faxes. TX means Transmit. RX means Receive.
Fax Receive Code Press this code ( 51,
91 for New Zealand)
when you answer a fax call on an extension or external phone.
Fax Storage You can store faxes in memory.
GLOSSARY G - 2
Fax tones The signals sent by sending and receiving fax machines
while communicating information.
Fax/Tel You can receive faxes and telephone calls. Do not use this
mode if you are using a telephone answering device (TAD).
Fine resolution Resolution is 203 x 196 dpi. It is used for small print
and graphs.
Gray scale The shades of gray available for copying and faxing
photographs.
Group number A combination of One-Touch and Speed-Dial
numbers that are stored on a One-Touch key or in a Speed-Dial
location for Broadcasting.
Help list A printout of the complete Menu table that you can use to
program your machine when you do not have the User’s Guide
with you.
Journal Period The pre-programmed time period between
automatically printed Fax Journal Reports. You can print the Fax
Journal on demand without interrupting the cycle.
LCD (liquid crystal display) The display screen on the machine
that shows interactive messages during On-Screen Programming
and shows the date and time when the machine is idle.
Manual fax When you lift the handset of the machine (FAX-1840C
only) or external telephone so you can hear the receiving fax
machine answer before you press Mono Start or Colour Start
to begin transmission.
Menu mode Programming mode for changing your machine’s
settings.
OCR (optical character recognition) (MFC-3240C only) The
bundled ScanSoft® OmniPage® software application converts an
image of text to text you can edit.
One-Touch Keys on the machine’s control panel where you can
store numbers for easy dialling. You can store a second number
on each key if you press Shift and the One-Touch Key together.
Out of Paper Reception Receives faxes into the machine’s
memory when the machine is out of paper.
G - 3 GLOSSARY
Overseas Mode Makes temporary changes to the fax tones to
accommodate noise and static on overseas phone lines.
Pause Allows you to place a 3.5 second delay in the dialling
sequence stored on One-Touch keys and Speed-Dial numbers.
Press Redial/Pause as many times as needed for longer
pauses.
Photo resolution A resolution setting that uses varying shades of
gray for the best representation of photographs.
Polling The process of a fax machine calling another fax machine
to retrieve waiting fax messages.
Pulse A form of rotary dialling on a telephone line.
Quick Dial List A listing of names and numbers stored in
One-Touch and Speed-Dial memory, in numerical order.
Real Time Transmission When memory is full, you can send faxes
in real time.
Remaining jobs You can check which jobs are waiting in memory
and cancel jobs individually.
Remote Access Code Your own four-digit code (--- ) that allows
you to call and access your machine from a remote location.
Remote Retrieval Access The ability to access your machine
remotely from a touch tone phone.
Resolution The number of vertical and horizontal lines per inch.
See: Standard, Fine, Super Fine and Photo.
Ring Delay The number of rings before the machine answers in
Fax Onlyand Fax/Telmode.
Ring Volume Volume setting for the machine’s ring.
Scanning (MFC-3240C only) The process of sending an electronic
image of a paper document into your computer.
Search An electronic, alphabetical listing of stored One-Touch,
Speed-Dial and Group numbers.
Speed-Dial A pre-programmed number for easy dialling. You must
press the Search/Speed Dial, #, and the two digit code, and
Mono Start or Colour Start to start the dialling process.
GLOSSARY G - 4
Standard resolution 203 x 97 dpi. It is used for regular size text
and quickest transmission.
Station ID The stored information that appears on the top of faxed
pages. It includes the sender’s name and fax number.
Super Fine resolution 392 x 203 dpi. Best for very small print and
line art.
TAD (telephone answering device) You can connect an external
TAD to your machine.
Temporary settings You can select certain options for each fax
transmission and copy without changing the default settings.
Tone A form of dialling on the telephone line used for Touch Tone
telephones.
Transmission The process of sending faxes over the phone lines
from your machine to the receiving fax machine.
User Settings A printed report that shows the current settings of the
machine.
Xmit Report (Transmission Verification Report) A listing for
each transmission, that shows its date, time and number.
G - 5 GLOSSARY
Specifications
S
Product description
General
Memory Capacity
8 MB
Automatic Document
Feeder (ADF)
Up to 20 pages
Temperature: 20°C - 30°C
Humidity: 50% - 70%
Paper: 80 gsm A4 size
Paper Tray
100 Sheets 80 gsm
Ink Jet
Printer Type
Print Method
Piezo with 74 × 5 nozzles
16 characters × 1 line
LCD (Liquid Crystal
Display)
Power Source
220 - 240V 50/60Hz
Power Save
Power Consumption
Mode:
Average 4 W
Average 8 W
Average 23 W
Standby:
Operating:
SPECIFICATIONS S - 1
Dimensions
388 mm
277 mm
191 mm
361 mm
373 mm
551 mm
402 mm
364 mm
322 mm
364 mm
Weight
Noise
5 kg
Operating:
42.5 to 51 dB*
* It depends on printing conditions
Temperature
Humidity
Operating:
105 - 35°C
Best Print
Quality:
20 - 33°C
Operating:
20 to 80% (without condensation)
Best Print
Quality:
20 to 80% (without condensation)
S - 2 SPECIFICATIONS
Print media
Paper Input
Paper Tray
■
Paper type:
Plain paper, inkjet paper (coated paper), glossy
paper*2, transparencies*1*2 and envelopes
■
Paper size:
Letter, Legal*3, Executive, A4, A5, A6, JIS_B5,
envelopes (commercial No.10, DL, C5,
Monarch, JE4), Photo card, Index card and
Post card.
■
Maximum paper tray capacity: Approx. 100
sheets of 80 gsm plain paper
Paper Output
Up to 50 sheets of Letter (A4) plain paper (Face up
print delivery to the output paper tray)*2
*1 Use only transparencies recommended for inkjet printing.
2
*
For glossy paper or transparencies, we recommend removing
printed pages from the output paper tray immediately after they
exit the machine to avoid smudging.
3
*
Legal paper cannot be stacked on the output paper tray.
Copy
Colour/Mono
Colour/Black
Document Size
ADF Width: 89 mm to 216 mm
ADF Height: 127 mm to 356 mm
Copy Speed
Mono
Up to 17 pages/minute (Letter/A4 paper)*
Colour
Up to 11 pages/minute (Letter/A4 paper)*
* Does not include the time it takes to feed the paper.
Based on Brother standard pattern. (Fast mode/Stack Copy)
Copy speeds vary with the complexity of the document.
Multiple Copies
Enlarge/Reduce
Resolution
Stacks up to 99 pages
25% to 400% (in increments of 1%)
Up to 600 x 1200 dpi copy resolution for plain, inkjet
or glossy paper and up to 1200 x 1200 dpi for
OHP/transparency
SPECIFICATIONS S - 3
Fax
Compatibility
Coding System
Modem Speed
ITU-T Group 3
MH/MR/MMR/JPEG
Automatic Fallback
14400 bps (FAX-1840C)
33600 bps (MFC-3240C)
Document Size
ADF Width: 89 mm to 216 mm
ADF Height: 127 mm to 356 mm
Scanning Width
Printing Width
Gray Scale
208 mm
204 mm
256 levels
Polling Types
Contrast Control
Standard, Secure, Timer Sequential: (B&W only)
Automatic/Light/Dark
(manual setting)
Resolution
• Horizontal 203 dot/inch (8 dot/mm)
• Vertical Standard -
98 line/inch (3.85 line/mm) (Mono)
196 line/inch (7.7 line/mm) (Colour)
Fine - 196 line/inch (7.7 line/mm) (Mono/Colour)
Photo - 196 line/inch (7.7 line/mm) (Mono)
Superfine - 392 line/inch (15.4 line/mm) (Mono)
One-Touch Dial
Speed-Dial
10 (5 x 2)
40 stations
Broadcasting
Automatic Redial
Auto Answer
100 stations
3 times at 5 minute intervals
2, 3, 4, 5, 6, 7, 8, 9 or 10 rings (for Australia)
1, 2, 3, 4, 5, 6, 7, 8, 9 or 10 rings (for New Zealand)
0, 1, 2, 3, 4, 5, 6, 7, 8, 9 or 10 rings
(for some countries)
S - 4 SPECIFICATIONS
Communication Source
Memory Transmission
Public Switched Telephone Network.
Up to 300*1/250*2 pages (FAX-1840C)
Up to 200*1/170*2 pages (MFC-3240C)
Out of Paper Reception
Up to 300*1/250*2 pages (FAX-1840C)
Up to 200*1/170*2 pages (MFC-3240C)
*1
*2
“Pages” refers to the “Brother Standard Chart No. 1” (a typical business letter, Standard resolution,
MMR code). Specifications and printed materials are subject to change without prior notice.
"Pages" refers to the "ITU-T Test Chart #1" (a typical business letter, Standard resolution, MMR code).
Specifications and printed materials are subject to change without prior notice.
Scanner (MFC-3240C only)
Colour/Monochrome
Colour/Monochrome
TWAIN Compliant
Yes (Windows® 98/98SE/Me/2000 Professional/XP)
Mac OS® 8.6-9.2/Mac OS® X 10.2.4 or greater
WIA Compliant
Colour Depth
Yes (Windows® XP)
36 bit colour (Input)
24 bit colour (Output)
Resolution
Up to 2400 × 2400 dpi (interpolated)*
Up to 600 × 1200 dpi (optical)
* Maximum 1200 x 1200 dpi scanning with Windows® XP
(resolution up to 2400 x 2400 dpi can be selected by using the
Brother scanner utility)
Scanning Speed
Document Size
Colour: up to 8.89 sec.
Mono: up to 3.99 sec.
(A4 size in 100 × 100 dpi)
ADF Width: 89 mm to 216 mm
ADF Height: 127 mm to 356 mm
Scanning Width
Gray Scale
210 mm
256 levels
Mac OS® X scanning is supported in Mac OS® X 10.2.4 or greater.
SPECIFICATIONS S - 5
Printer
For FAX-1840C, you can download the Brother Printer Driver
from the Brother Solutions Center. Visit us at:
Printer Driver
Resolution
Windows® 98/98SE/Me/2000 Professional and XP
driver supporting Brother Native Compression
mode and bi-directional capability
Apple® Macintosh® QuickDraw® Driver
For Mac OS® 8.6-9.2/Mac OS® X 10.2.4 or greater
Up to 1200 x 6000 dots per inch (dpi)*
1200 x 1200 dots per inch (dpi)
600 x 600 dots per inch (dpi)
600 x 150 dots per inch (dpi)
* Output image quality varies based upon many factors including
but not limited to input image resolution and quality and print
media.
Print Speed
up to 20 pages/minute (Mono)*
up to 15 pages/minute (Colour)*
* Based on Brother standard pattern.
A4 size in draft mode.
Does not include the time it takes to feed the paper.
Printing Width
204 mm (216 mm*)
* When you set the Borderless feature to On.
Disk-Based Fonts
Borderless
35 TrueType
Letter, A4, A6, Photo Card, Index Card, Post Card
S - 6 SPECIFICATIONS
Interfaces
USB
A Full-Speed USB 2.0 cable that is no longer than
2.0 m*
* Your machine has a Full-Speed USB 2.0 interface. This
interface is compatible with Hi-Speed USB 2.0; however, the
maximum data transfer rate will be 12 Mbits/s. The machine can
also be connected to a computer that has a USB 1.1 interface.
Computer requirements
Minimum System Requirements
Computer Platform & Operating System
Version
Processor
Minimum
Speed
Minimum
RAM
Recommended
RAM
Available Hard
Disk Space for
Drivers
1
Windows®
*
98, 98SE
Pentium II or
equivalent
32 MB
64 MB
90 MB
Operating System
Me
2000 Professional
XP*2
64 MB
128 MB
256 MB
64 MB
128 MB
150 MB
80 MB
Apple® Macintosh®
Operating System
Mac OS® 8.6
All base models meet
minimum Requirements
(Printing and PC-FAX
Send*4 Only)
Mac OS® 9.X
(Printing and PC-FAX
Send*3 Only)
Mac OS® X 10.2.4 or
greater
128 MB
160 MB
NOTE: All registered trademarks referenced herein are the property of their respective companies.
*1 Microsoft® Internet Explorer 5 or greater.
*2 Maximum 1200 x 1200 dpi scanning with Windows® XP. (Resolutions up to 2400 x 2400 dpi can be
selected using the Brother Utility.)
*3 PC Fax supports black and white faxing only.
SPECIFICATIONS S - 7
Consumable items
Ink
The machine uses individual Black, Yellow, Cyan
and Magenta ink cartridges that are separate from
the print head assembly.
Service Life of Ink
Cartridge
Standard Black - Approximately 500 pages at 5%
coverage
High Yield Black - Approximately 900 pages at 5%
coverage
Yellow, Cyan and Magenta - Approximately 400
pages at 5% coverage
The above figures are based upon the following
assumptions:
• Continuous printing at a resolution of 600 x 600
dpi in normal mode after installing new ink
cartridge;
• The printing frequency;
• The number of pages printed;
• Periodic, automatic, print head assembly cleaning
(Your machine will clean the print head assembly
periodically. This process will use a small amount
of ink); and,
• Ink remaining in cartridge identified as “empty” (It
is necessary to leave a small amount of ink in the
ink cartridge to prevent air from drying out and
damaging the print head assembly).
Replacement
Consumables
<Standard Black> LC47BK
<High Yield Black> LC47HYBK
<Cyan> LC47C
<Magenta> LC47M
<Yellow> LC47Y
S - 8 SPECIFICATIONS
Optional External Wireless Print/Scan
Server (NC-2200w) (MFC-3240C only)
NC-2200w External
Wireless Print/Scan
Server (Optional)
Connecting the optional External Wireless
Print/Scan Server (NC-2200w) to your machine will
allow you to print and scan over a wireless network.
Network types
Support for
IEEE 802.11b wireless LAN
Windows® 98/98SE/Me/2000/XP
Mac OS® X 10.2.4 or greater
Protocols
TCP/IP
ARP, RARP, BOOTP, DHCP, APIPA (Auto IP),
WINS/NetBIOS, DNS, LPR/LPD, Port9100,
SMB Print, IPP, RawPort, mDNS, TELNET, SNMP,
HTTP
You can assign the scan key to one networked
computer only.
SPECIFICATIONS S - 9
retrieving from a remote
cancelling from memory
from memory
Real Time Transmission
E
ECM
Extension telephone,
External telephone,
Fax/Tel mode
answering at extension
double-ringing
Telephone Answer Code
F
Fax codes
Telephone Answer Code
Fax Forwarding
Fax, stand-alone
G
INDEX I - 2
Multi-line connections (PBX)
H
HELP
O
One-Touch numbers
Options key (copying)
I
Ink cartridges
P
Paging
programming your pager
J
Phone line
Jacks
EXT
TAD (answering machine)
L
Print
Programming your MFC
LCD (liquid crystal display)
M
Manual
Mode, entering
I - 3 INDEX
Resolution
Q
Access codes and credit
setting up .......................5-6
Group dial
setting up Groups for
One-Touch dial
fax (Standard, Fine,
Speed-Dial
S
Setup
Station ID (fax header)
Speed-Dial
R
Reducing
T
INDEX I - 4
if you are having difficulty with
Printing Received
V
I - 5 INDEX
Remote Retrieval Access card
If you plan to receive fax messages while away from your machine,
carrying the Remote Retrieval Access Card printed below will serve
as a convenient reminder of the retrieval procedures. Simply cut out
the card and fold it to fit your wallet or organizer. Keeping it handy will
help you derive the full benefit of your machine’s Paging, Fax
Forwarding, and Remote Retrieval features.
ADR
C
CSE
A
TIREVAL
R
MTOE
1
2
4
5
6
3
R
Fold
Fold
REMOTE RETRIEVAL ACCESS CARD R - 1
4
3
2
1
Fold
Fold
R - 2
Visit us on the World Wide Web
This machine is approved for use in the country of purchase only, local
Brother companies or their dealers will only support machines purchased in
their own countries.
ARL/ASA/NZ
LF75370011
|