DV7210EL
DV1010EL
DV1410EL
DV1810EL
G
H
I
J
K
3
(Original instructions)
ENGLISH
Intended use
u
Never pull the charger lead to discon-
nect the charger from the socket. Keep
the charger lead away from heat, oil
and sharp edges.
Your Black & Decker Dustbuster® handheld vacuum cleaner
has been designed for light dry vacuum cleaning purposes.
This appliance is intended for household use only.
Safety instructions
u
This appliance can be used by chil-
dren aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge if
they have been given supervision or
instruction concerning use of the appli-
ance in a safe way and understand the
hazards involved. Children shall not
play with the appliance. Cleaning and
user maintenance shall not be made
by children without supervision.
Warning! Read all safety
@
warnings and all in-
structions. Failure to follow
the warnings and instructions
listed below may result in electric
shock, fire and/or serious injury.
Warning!When using battery-
powered appliances, basic safety
precautions, including the follow-
ing, should always be followed to
reduce the risk of fire, leaking bat-
teries, personal injury and material
damage.
@
InBsepfoercetuisoen, cahencdk threepapapilriasnce for
u
u
u
Read all of this manual carefully be-
fore using the appliance.
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may af-
fect its operation.
The intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
u
u
Do not use the appliance if any part is
damaged or defective.
Have any damaged or defective parts
repaired or replaced by an authorized
repair agent.
u
Retain this manual for future refer-
ence.
u
u
Regularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
Never attempt to remove or replace
any parts other than those specified in
this manual.
Using your appliance
u
Do not use the appliance to pick up
liquids or any materials that could
catch fire.
u
u
Do not use the appliance near water.
Do not immerse the appliance in
water.
4
(Original instructions)
ENGLISH
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Additional safety instructions
After use
u Unplug the charger before cleaning the charger or charg-
ing base.
u When not in use, the appliance should be stored in a dry
place.
u Children should not have access to stored appliances.
Chargers
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
u Use your Black & Decker charger only to charge the bat-
tery in the appliance/tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge nonrechargeable batteries.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u The appliance/tool/battery must be placed in a well venti-
lated area when charging.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Electrical safety
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the charger unit with
a regular mains plug.
Batteries and chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
Symbols on the charger
u Do not expose the battery to heat.
u Do not store in locations where the temperature may
exceed 40°C.
u Charge only at ambient temperatures between 10°C and
40°C.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
#
u Charge only using the charger provided with the appli-
ance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u Do not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and fire.
u Do not charge damaged batteries.
The charging base is intended for indoor use only.
$
u Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
u In case of skin or eye contact, follow the instructions
below.
5
(Original instructions)
ENGLISH
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
Features
This tool includes some or all of the following features.
1. On/off switch
The charge is complete when the charging indicator (3) lights
continuously. The charger and the battery can be left connect-
ed indefinitely with the LED illuminated. The LED will change
to flashing (charging) state as the charger occasionally tops
off the battery charge. The charging indicator (3) will be lit as
long as the battery is connected to the plugged-in charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
2. Bowl release button
3. Charging indicator
4. Dust bowl
5. Dust collector
6. Charger
7. Charging base
Assembly
Accessories (fig. A, B & C)
These models may be supplied with some of the following
accessories:
u A brush tool (8) for furniture and stairs.
u An Integrated brush tool (9) for furniture and stairs.
u An Integrated crevice tool (10) for confined spaces.
Battery diagnostics
If the appliance detects a weak battery, the charging indica-
tor (3) will flash at a fast rate when the power button (1) is
activated. Proceed as follows:
u Place the appliance on the charging base (7)
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge.
Fitting the brush tool (Fig. A). (DV7210EL Only)
u Insert the accessory into the front of the appliance. Make
sure that the accessory is pushed fully in.
The integrated brush tool (Fig. B). (DV1010EL, DV1410EL
and DV1810EL Only)
u Flip down the brush tool (9) at the end of the dust collec-
If the appliance detects a damaged battery, the charging
indicator (3) will flash at a fast rate when the appliance is on
the charger base. Proceed as follows:
tor.
u Take the appliance and the charger to be tested at an
authorised services centre.
The integrated crevice tool (Fig. C). (DV1010EL, DV1410EL
and DV1810EL Only)
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink, fast and slow, one
flash at each speed and repeat.
u Extend the crevice tool (10) by pulling the crevice tool (10)
until it locks into position.
u Retract the crevice tool (10) by pressing the area (11) and
pushing the crevice tool (10) back into the dust collector
(5).
Switching on and off (fig. E)
u To switch the appliance on, slide the on/off switch (1)
forward to position 1.
u To switch the appliance off, slide the on/off switch (1) back
to position 0.
Use
u Before first use, the battery must be charged.
u Place the appliance on the charging base whenever it is
not in use.
Rotating the dust collector (fig. F) (DV1010EL,
DV1410EL and DV1810EL only
The nozzle can be rotated for better access in tight spots.
u Press the rotation release catch (12).
u Rotate the nozzle to the left or right until it clicks into
place.
Charging the battery (Fig. D)
u Place the appliance on the charging base (7)
u Plug in the charger. Switch on at the mains. The charging
indicator (3) will flash continuously (slowly)
u Leave the appliance to charge.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
6
(Original instructions)
ENGLISH
Emptying and cleaning the product.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Emptying the dust bowl (fig. G).
u Press the release latch (13) and pull the dust collector (5)
straight off.
u Empty the contents of the bowl.
u To replace the dust collector, place it back onto the handle
until it “clicks” firmly into position.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
Removing the dust bowl and filters (fig. H, I, J & K).
Warning! The filters are re-usable and should be cleaned
regularly.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Press the release latch (2) and pull the dust bowl (4)
straight off.
u While holding the dust bowl over a bin or sink, pull out the
filter (14) to empty the contents of the bowl.
u To replace the dust bowl, place it back onto the handle
until it “clicks” firmly into position.
Warning! Never use the appliance without the filters. Opti-
mum dust collection will only be achieved with clean filters.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Pre-filter (fig. J) (DV7210EL and DV1010EL)
The Filter and pre-filter can be separated to allow better
cleaning.
Z
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
u Twist the pre-filter (16) in a clockwise direction and lift
from the filter (15).
Quick clean filter (fig. K) (DV1410EL and DV1810EL
u Lift the filter cleaning handle (19).
Separate collection of used products and packaging
u Whilst holding the quick clean filter housing (17) turn the
filter cleaning handle (18) to perform a quick clean of the
filter (18).
u Pull the filter (18) out of the quick clean filter housing (17)
for more thorough cleaning.
z
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Cleaning the dust bowls and filters
u The dust bowls and filters can be washed in warm soapy
water.
u Make sure that the filters and the dust bowl are dry before
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
re-fitting.
Replacing the filters
The filters should be replaced every 6 to 9 months and when-
ever worn or damaged.
Replacement filters are available from your Black & Decker
dealer:
For models: DV7210EL and DV1010EL use filter part number
VF110-XJ
For models: DV1410EL and DV1810EL use filter part number
VF110FC-XJ
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
7
(Original instructions)
ENGLISH
Battery
Technical data
DV7210EL
DV1010EL
If you want to dispose of the product yourself, the
battery must be removed as described below and
disposed of in accordance with local regulations.
(H1)
(H1)
Z
Voltage
Battery
Weight
Charger
Vdc
7.2
10.8
u Preferably discharge the battery by operating the appli-
ance until the motor stops.
u Press the release button (2) and remove the dust bowl (4).
u Remove the seven screws holding the body of the appli-
ance together.
u Lift the housing cover away from the assembly.
u Detach all lead connections from the battery pack.
u Remove battery pack.
u Place the battery in a suitable packaging to ensure that
the terminals cannot be short-circuited.
Type
kg
Li-Ion
Li-Ion
1.11
1.18
S010QB1400040
S010QB1400040
Input voltage
Output voltage
Current
Vac
Vdc
mA
h
100-240
100-240
14
400
4
14
400
4
u Take the battery to your service agent or to a local recy-
cling station.
Once removed, the battery cannot be refitted.
Approximate
charge time
Weight
kg
0.16
0.16
DV1410EL
DV1810EL
(H1)
(H1)
Voltage
Battery
Weight
Charger
Vdc
14.4
18
Type
kg
Li-Ion
Li-Ion
1.23
1.3
S010QB2300040
S010QB2300040
Input voltage
Output voltage
Current
Vac
Vdc
mA
h
100-240
100-240
23
400
4
23
400
4
Approximate
charge time
Weight
kg
0.18
0.18
8
(Original instructions)
ENGLISH
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
9
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Slough, Berkshire SL1 3YD
90614290 REV-0
07/2014
|