User Guide
15060-0NE4R000
E14752
Side and rear features
Microphone
Audio jack
Camera flash
Rear cameras
Fingerprint sensor
Volume
key
Power
key
Eject hole
Nano SIM1, Nano SIM2, Micro SD card slot
Speaker
Microphone
Micro USB port
Charging your ASUS Phone
To charge your ASUS Phone:
1. Connect the USB connector into the power
adapter’s USB port.
2. Connect the other end of the USB cable to your
ASUS Phone.
3. Plug the power adapter into a wall socket.
3
2
1
IMPORTANT!
•
•
•
When using your ASUS Phone while it is plugged to
a power outlet, the grounded power outlet must be
near to the unit and easily accessible.
When charging your ASUS Phone through your
computer, ensure that you plug the USB cable to
your computer’s USB port.
Avoid charging your ASUS Phone in an environment
with ambient temperature of above 35oC (95oF).
NOTES:
•
For safety purposes, use ONLY the bundled power
adapter and cable to avoid damaging your device
and prevent the risk of injury.
•
•
For safety purposes, use ONLY the bundled power
adapter and cable to charge your ASUS Phone.
The input voltage range between the wall outlet
and this adapter is AC 100V - 240V. The output
voltage of the USB cable is +5V 2A, 10W.
Installing a Nano SIM/ microSD card
To install a Nano SIM/ microSD card:
1. Push the bundled eject pin into the hole on the
card slot to eject the tray out.
2. Insert the Nano SIM or microSD card into the
appropriate slot.
3. Push the tray to close it.
NOTES:
•
Both Nano SIM card slots support GSM/GPRS/ EDGE,
WCDMA/HSPA+/DC-HSPA+, FDD-LTE, and TD-LTE
DSDV network bands. Both Nano SIM cards can
connect to VoLTE 4G calling service. But only one
can connect to FDD-LTE, and TD-LTE data service at a
time.
•
•
ASUS phone 2G/3G/4G/LTE band compatibility
varies by region. Check compatibility with your local
carriers.
The microSD card slot supports microSD and
microSDXC card formats.
CAUTION!
•
Do not use sharp tools or solvent on your device to
avoid scratches on it.
•
Use only a standard Nano SIM card on your ASUS
Phone.
Federal Communications
Commission Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user‘s authority to operate the equipment.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment
and receiver.
-
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-
Consult the dealer or an experienced radio/TV
technician for help.
The antenna(s) used for this transmitter must not be
co-located or operated in conjunction with any other
antenna or transmitter.
The country code selection is for non-US models
only and is not available to all US models. Per FCC
regulation, all WiFi products that are marketed in US
must be fixed to US-operated channels only.
The responsible party within the USA per 47 CFR Part
2.1077(a)(3):
ASUS COMPUTER INTERNATIONAL (America)
Address: 48720 Kato Rd., Fremont, CA 94538, USA
Telephone: +1-510-739-3777
RF Exposure Information (SAR)
This device has been tested and meets applicable
limits for Radio Frequency (RF) exposure.
Specific Absorption Rate (SAR) refers to the rate at
which the body absorbs RF energy. SAR limits are
1.6 Watts per kilogram (over a volume containing
a mass of 1 gram of tissue) in countries that follow
the United States FCC limit and 2.0 W/kg (averaged
over 10 grams of tissue) in countries that follow the
Council of the European Union limit. Tests for SAR are
conducted using standard operating positions with
the device transmitting at its highest certified power
level in all tested frequency bands.
To reduce exposure to RF energy, use a hands-free
accessory or other similar option to keep this device
away from your head and body. Carry this device
at least 10 mm away from your body to ensure
exposure levels remain at or below the as-tested
levels. Choose the belt clips, holsters, or other
similar body-worn accessories which do not contain
metallic components to support operation in this
manner. Cases with metal parts may change the RF
performance of the device, including its compliance
with RF exposure guidelines, in a manner that has
not been tested or certified, and use such accessories
should be avoided.
The highest FCC SAR values for the device are as
follows:
•
•
1.04 W/Kg @1g(Head)
0.99 W/Kg @1g(Body)
The FCC has granted an Equipment Authorization for
this device with all reported SAR levels evaluated as
in compliance with the FCC RF exposure guidelines.
SAR information on this device is on file with the FCC
and can be found under the Display Grant section
ID: MSQX01AD.
FCC Statement (HAC)
This phone has been tested and rated for use with
hearing aids for some of the wireless technologies
that it uses. However, there may be some newer
wireless technologies used in this phone that have
not been tested yet for use with hearing aids. It is
important to try the different features of this phone
thoroughly and in different locations, using your
hearing aid or cochlear implant, to determine if
you hear any interfering noise. Consult your service
provider or the manufacturer of this phone for
information on hearing aid compatibility. If you have
questions about return or exchange policies, consult
your service provider or phone retailer.
The Federal Communications Commission has
implemented rules and a rating system designed
to enable people who wear hearing aids to more
effectively use these wireless telecommunications
devices. The standard for compatibility of digital
wireless phones with hearing aids is set forth in
American National Standard Institute (ANSI) standard
C63.19-2011. There are two sets of ANSI standards
with ratings from one to four (four being the best
rating): an “M”rating for reduced interference
making it easier to hear conversations
on the phone when using the hearing aid
microphone, and a“T”rating that enables the phone
to be used with hearing aids operating in the telecoil
mode thus reducing unwanted background noise.
The Hearing Aid Compatibility rating is displayed on
the wireless phone box.
A phone is considered Hearing Aid Compatible
for acoustic coupling (microphone mode) if it has
an “M3”or “M4”rating. A digital wireless phone is
considered Hearing Aid Compatible for inductive
coupling (telecoil mode) if it has a“T3”or“T4”rating.
The tested M-Rating and T-Rating for this device are
M3 and T3.
You’ll want to try a number of wireless phones so
that you can decide which works the best with your
hearing aids. You may also want to talk with your
hearing aid professional about the extent to which
your hearing aids are immune to interference, if they
have wireless phone shielding, and whether your
hearing aid has a HAC rating.
Canada, Industry Canada (IC)
Notices
This device complies with Industry Canada’s licence-
exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux normes CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence. Son utilisation est sujette aux
deux conditions suivantes :
(1) Cet appareil ne doit pas créer d’interférences
nuisibles, et
(2) Cet appareil doit tolérer tout type
d’interférences, y compris celles susceptibles de
provoquer un fonctionnement non souhaité de
l’appareil.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device
is below the Industry Canada (IC) radio frequency
exposure limits. The Wireless Device should be used
in such a manner such that the potential for human
contact during normal operation is minimized. This
device has been evaluated for and shown compliant
with the IC Specific Absorption Rate (“SAR”) limits
when installed in specific host products operated in
portable exposure conditions.
Canada’s REL (Radio Equipment List) can be found at
sitt/reltel/srch/nwRdSrch.do?lang=eng.
Additional Canadian information on RF exposure
also can be found at the following web address:
sf08792.html.
This equipment should be installed and operated
with minimum distance 10 mm between the radiator
and your body.
Informations concernant l’exposition aux
fréquences radio (RF)
La puissance de sortie émise par cet appareil sans fil
est inférieure à la limite d’exposition aux fréquences
radio d’Industrie Canada (IC). Utilisez l’appareil sans
fil de façon à minimiser les contacts humains lors
d’un fonctionnement normal.
Cet appareil été évalué et démontré conforme
aux limites de DAS (Débit d’absorption spécifique)
d’IC lorsqu’il est installé dans des produits hôtes
particuliers qui fonctionnent dans des conditions
d’exposition à des appareils portables.
Ce périphérique est homologué pour l’utilisation
au Canada. Pour consulter l’entrée correspondant
à l’appareil dans la liste d’équipement radio (REL
- Radio Equipment List) d’Industrie Canada rendez-
vous sur :
do?lang=eng.
Pour des informations supplémentaires concernant
l’exposition aux ondes radio au Canada, rendez-vous
sur :
sf08792.html.
Cet appareil doit être installé et utilisé avec un
minimum de 10 mm de distance entre la source de
rayonnement et votre corps.
CAN ICES-3(B)/NMB-3(B)
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
This device and its antenna(s) must not be co-
located or operated in conjunction with any other
antenna or transmitter, except tested built-in radios.
The County Code Selection feature is disabled for
products that are marketed in the US/ Canada.
Cet appareil et son ou ses antenne(s) ne doivent pas
être situés près de ou utilisés conjointement avec
une autre antenne ou un autre émetteur, exception
faite des radios intégrées qui ont été testées.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux
États-Unis et au Canada.
The IC ID for this device is 3568A-X01AD.
L’identifiant Industrie Canada de cet appareil est:
3568A-X01AD.
Using GPS (Global Positioning
System) on your ASUS Phone
To use the GPS positioning feature on your ASUS
Phone:
•
•
•
Ensure that your device is connected to the
Internet before using Google Map or any
GPS-enabled apps.
For first-time use of a GPS-enabled app on
your device, ensure that you are outdoors to
get the best positioning data.
When using a GPS-enabled app on your
device inside a vehicle, the metallic
component of the car window and other
electronic devices might affect the GPS
performance.
Safety information
CAUTION! Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
ASUS Phone care
•
Use your ASUS Phone in an environment with
ambient temperatures between 0 °C (32 °F) and
35 °C (95 °F).
The battery
WARNING: Disassembling the battery by yourself
will void its warranty and may cause serious harm.
Your ASUS Phone is equipped with a high
performance non-detachable Li-polymer battery.
Observe the maintenance guidelines for a longer
battery life.
•
Do not remove the non-detachable li-polymer
battery as this will void the warranty.
•
Avoid charging in extremely high or low
temperature. The battery performs optimally in
an ambient temperature of +5 °C to +35 °C.
•
•
Do not remove and replace the battery with a
non-approved battery.
Use only ASUS battery. Using a different battery
may cause physical harm/injury and may
damage your device.
•
•
Do not remove and soak the battery in water or
any other liquid.
Never try to open the battery as it contains
substances that might be harmful if swallowed
or allowed to come into contact with
unprotected skin.
•
•
•
Do not remove and short-circuit the battery, as
it may overheat and cause a fire. Keep it away
from jewelry or metal objects.
Do not remove and dispose of the battery
in fire. It could explode and release harmful
substances into the environment.
Do not remove and dispose of the battery
with your regular household waste. Take it to a
hazardous material collection point.
•
•
Do not touch the battery terminals.
To avoid fire or burns, do not disassemble,
bend, crush, or puncture the battery.
NOTES:
•
Risk of explosion if battery is replaced by an
incorrect type.
•
Dispose of used battery according to the
instructions.
The charger
•
Use only the charger supplied with your ASUS
Phone.
•
Never pull the charger cord to disconnect it
from the power socket. Pull the charger itself.
Caution
Your ASUS Phone is a high quality piece of
equipment. Before operating, read all instructions
and cautionary markings on the (1) AC Adapter.
•
•
•
Do not use the ASUS Phone in an extreme
environment where high temperature or high
humidity exists. The ASUS Phone performs
optimally in an ambient temperature between
0 °C (32°F) and 35 °C (95 °F).
Do not disassemble the ASUS Phone or its
accessories. If service or repair is required,
return the unit to an authorized service center.
If the unit is disassembled, a risk of electric
shock or fire may result.
Do not short-circuit the battery terminals with
metal items.
Operator access with a tool
If a TOOL is necessary to gain access to an OPERATOR
ACCESS AREA, either all other compartments within
that area containing a hazard shall be inaccessible
to the OPERATOR by the use of the same TOOL, or
such compartments shall be marked to discourage
OPERATOR access.
Regional notice for Singapore
This ASUS Phone complies
with IMDA Standards.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come
from our commitment to the highest standards for
protecting our environment. We believe in providing
solutions for you to be able to responsibly recycle
our products, batteries, other components as well as
com/english/Takeback.htm for detailed recycling
information in different regions.
Proper disposal
Risk of explosion if battery is replaced
by an incorrect type. Dispose of used
batteries according to the instructions.
DO NOT throw the battery in municipal
waste. The symbol of the crossed out
wheeled bin indicates that the battery
should not be placed in municipal waste.
DO NOT throw this product in municipal
waste. This product has been designed
to enable proper reuse of parts and
recycling. The symbol of the crossed out
wheeled bin indicates that the product
(electrical, electronic equipment and
mercury-containing button cell battery)
should not be placed in municipal waste.
Check local regulations for disposal of
electronic products.
DO NOT throw this product in fire. DO
NOT short circuit the contacts. DO NOT
disassemble this product.
WARNING
Cancer and Reproductive Harm-
NOTE: For more legal and e-labelling information,
check on your device from Settings > About >
Legal information.
ASUS
Address: 4F, No.150 Li-Te Rd., Peitou, Taipei,
Taiwan
Tel: 886228943447
Fax: 886228907698
Declaration
We declare that the IMEI codes for this product, ASUS
Phone, are unique to each unit and only assigned to
this model. The IMEI of each unit is factory set and
cannot be altered by the user and that it complies
with the relevant IMEI integrity related requirements
expressed in the GSM standards.
Should you have any questions or comments regarding
this matter, please contact us.
Sincerely yours,
ASUSTeK COMPUTER INC.
Tel: 886228943447
Fax: 886228907698
Copyright © 2018 ASUSTeK COMPUTER INC.
All Rights Reserved.
You acknowledge that all rights of this Manual remain with ASUS.
Any and all rights, including without limitation, in the Manual or
website, and shall remain the exclusive property of ASUS and/or its
licensors. Nothing in this Manual intends to transfer any such rights,
or to vest any such rights to you.
ASUS PROVIDES THIS MANUAL“AS IS”WITHOUT WARRANTY OF
ANY KIND. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS
MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE
SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD
NOT BE CONSTRUED AS A COMMITMENT BY ASUS.
ZenTalk Fans Forum
(http://www.asus.com/zentalk/global_forward.php)
|