User Guide
15060-xxxxxxxx
E13955
Side features
Audio jack
Microphone
Nano SIM / Micro
SD card slot
Volume
key
Eject hole
Power
key
Microphone
Speaker
Micro USB port
Rear features
Rear camera
Flash
Fingerprint
sensor
Charging your ASUS Phone
To charge your ASUS Phone:
1. Connect the USB connector into the power
adapter’s USB port.
2. Connect the other end of the USB cable to your
ASUS Phone.
3. Plug the power adapter into a wall socket.
3
2
1
IMPORTANT!
•
When using your ASUS Phone while it is plugged to
a power outlet, the grounded power outlet must be
near to the unit and easily accessible.
•
•
When charging your ASUS Phone through your
computer, ensure that you plug the USB cable to
your computer’s USB port.
Avoid charging your ASUS Phone in an
environment with ambient temperature of above
35oC (95oF).
NOTES:
•
For safety purposes, use ONLY the bundled power
adapter and cable to avoid damaging your device
and prevent the risk of injury.
•
•
For safety purposes, use ONLY the bundled power
adapter and cable to charge your ASUS Phone.
The input voltage range between the wall outlet and
this adapter is AC 100V - 240V. The output voltage
of the USB cable is +5V 2A, 10W.
Installing a Nano SIM/ microSD
card
To install a Nano SIM/ microSD card:
1. Push the bundled eject pin into the hole on the
card slot to eject the tray out.
2. Insert the Nano SIM or microSD card into the
appropriate slot.
Nano-SIM
Micro SD
3. Push the tray to close it.
NOTES:
•
The Nano SIM card slots support GSM, WCDMA,
FDD-LTE, and TDD-LTE network bands.
•
The microSD card slot supports microSD and
microSDHC card formats.
CAUTION!
•
Do not use sharp tools or solvent on your device to
avoid scratches on it.
•
Use only a standard Nano SIM card on your ASUS
Phone.
Federal Communications
Commission Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user‘s authority to operate the equipment.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment
and receiver.
-
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-
Consult the dealer or an experienced radio/TV
technician for help.
The antenna(s) used for this transmitter must not be
co-located or operated in conjunction with any other
antenna or transmitter.
The country code selection is for non-US models
only and is not available to all US models. Per FCC
regulation, all WiFi products that are marketed in US
must be fixed to US-operated channels only.
The responsible party within the USA per 47 CFR
Part 2.1077(a)(3):
ASUS COMPUTER INTERNATIONAL (America)
Address: Corporate Way, Fremont, CA 94539, USA
Telephone: +1-510-739-3777
RF Exposure Information (SAR)
This device has been tested and meets applicable
limits for Radio Frequency (RF) exposure.
Specific Absorption Rate (SAR) refers to the rate at
which the body absorbs RF energy. SAR limits are
1.6 Watts per kilogram (over a volume containing
a mass of 1 gram of tissue) in countries that follow
the United States FCC limit and 2.0 W/kg (averaged
over XX grams of tissue) in countries that follow the
Council of the European Union limit. Tests for SAR
are conducted using standard operating positions
with the device transmitting at its highest certified
power level in all tested frequency bands.
To reduce exposure to RF energy, use a hands-free
accessory or other similar option to keep this device
away from your head and body. Carry this device
at least 10 mm away from your body to ensure
exposure levels remain at or below the as-tested
levels. Choose the belt clips, holsters, or other
similar body-worn accessories which do not contain
metallic components to support operation in this
manner. Cases with metal parts may change the RF
performance of the device, including its compliance
with RF exposure guidelines, in a manner that
has not been tested or certified, and use such
accessories should be avoided.
The highest FCC SAR values for the device are as
follows:
•
•
0.61 W/Kg @1g(Head)
1.09 W/Kg @1g(Body)
The FCC has granted an Equipment Authorization
for this device with all reported SAR levels evaluated
as in compliance with the FCC RF exposure
guidelines. SAR information on this device is on file
with the FCC and can be found under the Display
Grant section of www.fcc.gov/oet/ea/fccid after
searching on FCC ID: MSQX00PS.
FCC Statement (HAC)
This phone has been tested and rated for use with
hearing aids for some of the wireless technologies
that it uses. However, there may be some newer
wireless technologies used in this phone that have
not been tested yet for use with hearing aids. It is
important to try the different features of this phone
thoroughly and in different locations, using your
hearing aid or cochlear implant, to determine if you
hear any interfering noise. Consult your service
provider or the manufacturer of this phone for
information on hearing aid compatibility. If you have
questions about return or exchange policies, consult
your service provider or phone retailer.
The Federal Communications Commission has
implemented rules and a rating system designed
to enable people who wear hearing aids to more
effectively use these wireless telecommunications
devices. The standard for compatibility of digital
wireless phones with hearing aids is set forth
in American National Standard Institute (ANSI)
standard C63.19-2011. There are two sets of
ANSI standards with ratings from one to four (four
being the best rating): an “M” rating for reduced
interference making it easier to hear conversations
on the phone when using the hearing aid
microphone, and a “T” rating that enables the phone
to be used with hearing aids operating in the telecoil
mode thus reducing unwanted background noise.
The Hearing Aid Compatibility rating is displayed on
the wireless phone box.
A phone is considered Hearing Aid Compatible
for acoustic coupling (microphone mode) if it has
an “M3” or “M4” rating. A digital wireless phone is
considered Hearing Aid Compatible for inductive
coupling (telecoil mode) if it has a “T3” or “T4” rating.
The tested M-Rating and T-Rating for this device
are M4 and T3.
You’ll want to try a number of wireless phones so
that you can decide which works the best with your
hearing aids. You may also want to talk with your
hearing aid professional about the extent to which
your hearing aids are immune to interference, if they
have wireless phone shielding, and whether your
hearing aid has a HAC rating.
EU Radio Equipment Directive
Compliance
Simplified EU Declaration of Conformity
Hereby, ASUSTek Computer Inc. declares that the
radio equipment ASUS_X00PS is in compliance with
Directive 2014/53/EU. Full text of EU declaration
support/. (Search for ZB555KL)
RF Output Table
Items
Maximum Radio-Frequency Output Power Table
Bluetooth BR/EDR (2402~2480
MHz)
7.00(dBm)
Bluetooth
Bluetooth 4.0-LE (2402~2480 MHz) 2.00(dBm)
2.4GHz 802.11b (2412~2472 MHz) 15.50(dBm)
2.4GHz 802.11g (2412~2472 MHz) 14.00(dBm)
2.4GHz 802.11n HT20
(2412~2472MHz)
12.50(dBm)
12.50(dBm)
33.50(dBm)
30.00(dBm)
23.50(dBm)
23.50(dBm)
23.50(dBm)
23.50(dBm)
22.50(dBm)
WLAN
2.4GHz 802.11n HT40
(2422~2462MHz)
GSM 900 Burst (880~915 ;
925~960 MHz)
GSM
GSM 1800 Burst (1710~1785 ;
1805~1880 MHz)
WCDMA Band I (1920~1980 ;
2110~2170 MHz)
WCDMA
WCDMA Band VIII (880~915 ;
925~960 MHz)
LTE Band I (1920~1980 ;
2110~2170 MHz)
LTE Band III (1710~1785 ;
1805~1880 MHz)
LTE Band VII (2500~2570 ;
2620~2690 MHz)
LTE
LTE Band VIII (880~915 ; 925~960 23.00(dBm)
MHz)
LTE Band XX (832~862 ; 791~821
MHz)
23.50(dBm)
23.00(dBm)
LTE Band XL (2300~2400 MHz)
NOTE: This RF output power table is for EU
member states, the EEA States, the EFTA States
and Turkey only. The frequency range and the
RF output power may differ from other non-EU
countries.
RF Exposure Information
This ASUS product has been tested and meets
applicable European SAR limits. The SAR limit is
2.0 W/kg in countries that set the limit averaged
over 10 grams of tissue. The specific maximum SAR
values for this device are as follows:
ASUS_X00PS(ZB555KL)
•
•
Head: 0.397 W/Kg
Body: 1.130 W/Kg
When carrying this device or using it while worn on
the body, either use an approved accessory such
as a holster or otherwise maintain a distance of 0.5
cm from the body to ensure compliance with RF
exposure requirements.
This ASUS product has been tested and meets
applicable European SAR limits. The SAR limit is
2.0 W/kg in countries that set the limit averaged
over 1 grams of tissue. The specific maximum SAR
values for this device are as follows:
ASUS_X00PS(ZB555KL) for IN
•
•
Head: 0.821 W/Kg
Body: 1.180 W/Kg
When carrying this device or using it while worn on
the body, either use an approved accessory such
as a holster or otherwise maintain a distance of 1
cm from the body to ensure compliance with RF
exposure requirements.
CE Marking
Laser safety information
CLASS 1 LASER PRODUCT
Complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50,
dated June 24, 2007
Using GPS (Global Positioning
System) on your ASUS Phone
To use the GPS positioning feature on your ASUS
Phone:
•
•
•
Ensure that your device is connected to the
Internet before using Google Map or any
GPS-enabled apps.
For first-time use of a GPS-enabled app on
your device, ensure that you are outdoors to
get the best positioning data.
When using a GPS-enabled app on
your device inside a vehicle, the metallic
component of the car window and other
electronic devices might affect the GPS
performance.
Prevention of Hearing Loss
To prevent possible hearing damage, do not listen at
high volume levels for long periods.
Safety information
CAUTION! Use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
ASUS Phone care
•
Use your ASUS Phone in an environment with
ambient temperatures between 0 °C (32 °F)
and 35 °C (95 °F).
The battery
WARNING: Disassembling the battery by yourself
will void its warranty and may cause serious harm.
Your ASUS Phone is equipped with a high
performance non-detachable Li-polymer battery.
Observe the maintenance guidelines for a longer
battery life.
•
•
Do not remove the non-detachable li-polymer
battery as this will void the warranty.
Avoid charging in extremely high or low
temperature. The battery performs optimally in
an ambient temperature of +5 °C to +35 °C.
•
•
Do not remove and replace the battery with a
non-approved battery.
Use only ASUS battery. Using a different
battery may cause physical harm/injury and
may damage your device.
•
•
Do not remove and soak the battery in water or
any other liquid.
Never try to open the battery as it contains
substances that might be harmful if swallowed
or allowed to come into contact with
unprotected skin.
•
•
•
Do not remove and short-circuit the battery, as
it may overheat and cause a fire. Keep it away
from jewelry or metal objects.
Do not remove and dispose of the battery
in fire. It could explode and release harmful
substances into the environment.
Do not remove and dispose of the battery with
your regular household waste. Take it to a
hazardous material collection point.
•
•
Do not touch the battery terminals.
To avoid fire or burns, do not disassemble,
bend, crush, or puncture the battery.
NOTES:
•
Risk of explosion if battery is replaced by an
incorrect type.
•
Dispose of used battery according to the
instructions.
The charger
•
Use only the charger supplied with your ASUS
Phone.
•
Never pull the charger cord to disconnect it
from the power socket. Pull the charger itself.
Caution
Your ASUS Phone is a high quality piece of
equipment. Before operating, read all instructions
and cautionary markings on the (1) AC Adapter.
•
•
•
Do not use the ASUS Phone in an extreme
environment where high temperature or high
humidity exists. The ASUS Phone performs
optimally in an ambient temperature between 0
°C (32°F) and 35 °C (95 °F).
Do not disassemble the ASUS Phone or its
accessories. If service or repair is required,
return the unit to an authorized service center.
If the unit is disassembled, a risk of electric
shock or fire may result.
Do not short-circuit the battery terminals with
metal items.
Operator access with a tool
If a TOOL is necessary to gain access to an
OPERATOR ACCESS AREA, either all other
compartments within that area containing a hazard
shall be inaccessible to the OPERATOR by the use
of the same TOOL, or such compartments shall be
marked to discourage OPERATOR access.
General Usage (typical body-worn) (for
Japan)
This device (front & rear side) should be operated
under a seperation distance of 5 mm from the
human body.
* The other four sides are not in close proximity to
the human body at the general use as described
above.
India E-waste (Management and
handling) Rules 2016
This product complies with the “India E-Waste
(Management) Rules, 2016” and prohibits
use of lead, mercury, hexavalent chromium,
polybrominated biphenyls (PBBs) and
polybrominated diphenyl ethers (PBDEs) in
concentrations exceeding 0.1% by weight in
homogenous materials and 0.01 % by weight in
homogenous materials for cadmium, except for the
exemptions listed in Schedule II of the Rule.
India BIS - IS 16333 Notice
Language Input : Hindi, English, Tamil
Readability: Assamese, Bangla, Bodo(Boro),
Dogri, Gujarati, Hindi, Kannada, Kashmiri,
Konkani, Maithili, Malayalam, Manipuri(Bangla),
Manipuri(Meetei Mayek), Marathi, Nepali, Oriya,
Panjabi, Santhali, Sanskrit, Sindhi (Devanagari)
,Tamil, Telugu, Urdu and English
Regional notice for Singapore
This ASUS Phone
complies with IMDA
Standards.
ASUS Recycling/Takeback
Services
ASUS recycling and takeback programs come
from our commitment to the highest standards for
protecting our environment. We believe in providing
solutions for you to be able to responsibly recycle
our products, batteries, other components as well
as the packaging materials. Please go to http://
csr.asus.com/english/Takeback.htm for detailed
recycling information in different regions.
Proper disposal
Risk of explosion if battery is replaced
by an incorrect type. Dispose of used
batteries according to the instructions.
DO NOT throw the battery in municipal
waste. The symbol of the crossed out
wheeled bin indicates that the battery
should not be placed in municipal waste.
DO NOT throw this product in municipal
waste. This product has been designed
to enable proper reuse of parts and
recycling. The symbol of the crossed out
wheeled bin indicates that the product
(electrical, electronic equipment and
mercury-containing button cell battery)
should not be placed in municipal waste.
Check local regulations for disposal of
electronic products.
DO NOT throw this product in fire. DO
NOT short circuit the contacts. DO NOT
disassemble this product.
WARNING
Cancer and Reproductive Harm-
NOTE: For more legal and e-labelling information,
check on your device from Settings > About >
Legal information.
FCC COMPLIANCE INFROMATION
Per FCC Part 2 Section 2.1077
Responsible Party: Asus Computer International
Address:
800 Corporate Way, Fremont, CA 94539.
(510)739-3777/(510)608-4555
Phone/Fax No:
hereby declares that the product
Product Name :
Model Number :
Zenfone Max M1
ASUS_X00PS
compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Ver. 180125
ASUS
Address: 4F, No.150 Li-Te Rd., Peitou, Taipei,
Taiwan
Tel: 886228943447
Fax: 886228907698
Declaration
We declare that the IMEI codes for this product, ASUS
Phone, are unique to each unit and only assigned to
this model. The IMEI of each unit is factory set and
cannot be altered by the user and that it complies
with the relevant IMEI integrity related requirements
expressed in the GSM standards.
Should you have any questions or comments regarding
this matter, please contact us.
Sincerely yours,
ASUSTeK COMPUTER INC.
Tel: 886228943447
Fax: 886228907698
Copyright © 2018 ASUSTeK COMPUTER INC.
All Rights Reserved.
You acknowledge that all rights of this Manual remain with ASUS.
Any and all rights, including without limitation, in the Manual or
website, and shall remain the exclusive property of ASUS and/or its
licensors. Nothing in this Manual intends to transfer any such rights,
or to vest any such rights to you.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY
OF ANY KIND. SPECIFICATIONS AND INFORMATION
CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE
AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE
CONSTRUED AS A COMMITMENT BY ASUS.
ZenTalk Fans Forum
(http://www.asus.com/zentalk/global_forward.php)
|