GB
User manual
2
Washing Machine
ZWS 5883
Download from Www.Somanuals.com. All Manuals Search And Download.
• All packing and transit bolts must be removed • Never pull the power supply cable to remove
before use. Serious damage can occur to the
product and to property if this is not adhered
to. See relevant section in the user manual.
the plug from the socket; always take hold of
the plug itself.
• Never use the appliance if the power supply
cable, the control panel, the working surface
or the base are damaged so that the inside of
the washing machine is accessible.
• After having installed the appliance, check that
it is not standing on the inlet and drain hose
and the worktop is not pressing the electrical
supply cable against the wall.
Child safety
• If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely under the appliance.
• This appliance is not intended for use by per-
son (including children) with reduced physical
sensory or mental capabilities or lack of expe-
rience and knowledge unless they have been
givensupervisionorinstructionconcerninguse
of the appliance by a person responsible for
their safety.
• Always be sure, that there is no water leakage
from hoses and their connections after the in-
stallation.
• If the appliance is installed in a location subject
to frost, please read the “dangers of freezing”
chapter.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of chil-
dren’s reach
• Any plumbing work required to install this ap-
pliance should be carried out by a qualified
plumber or competent person.
• Keep all detergents in a safe place out of chil-
dren’s reach.
• Any electrical work required to install this ap-
pliance should be carried out by a qualified
electrician or competent person.
• Make sure that children or pets do not climb
into the drum. To prevent children and pets
becoming trapped inside the drum this ma-
chine incorporates a special feature.
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than
those for which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
• Do not overload the appliance. See the Wash-
ing Programme Table.
• Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and treat
stains such as paint, ink, rust, and grass before
washing. Underwired bras must NOT be ma-
chine washed.
To activate this de-
vice, rotate the button and restore the possi-
(without pressing it) bility of closing the
inside the door clock- door, rotate the but-
wise until the grooveis ton anti-clockwise un-
horizontal. If necessa- til the groove is verti-
To disable this device
• Garments which have been in contact with
volatile petroleum products should not be ma-
chine washed. If volatile cleaning fluids are
used, care should be taken to ensure that the
fluidisremoved fromthegarmentbeforeplac-
ing in the machine.
ry use a coin.
cal.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product description
1
Detergent dispenser drawer
1
2
2 Control panel
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for pre-
wash and soak phase or for stain remover used
during the stain action phase (if available). The
prewash and soak detergent is added at the be-
ginning of the wash programme. The stain re-
mover is added during the stain action phase.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent pour
it just before starting the programme.
Compartment for liquid additives (fabric soft-
ener, starch).
Follow the product manufacturer’s recommen-
dations on quantities to use and do not exceed
the «MAX» mark in the detergent dispenser
drawer. Any fabric softenerorstarching additives
must be poured into the compartment before
starting the wash programme.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
Belowisapictureofthecontrolpanel. Itshowstheprogrammeselectordialaswellasthebuttons,
pilot lights and the display. These are presented by relevant numbers on the following pages.
1
2
3
4
5
6
7
1
Programme selector dial
5 EXTRA RINSE button
6 START/PAUSE button
7 Indicator Pilot Light
2 Temperature selector dial
3 SPIN reduction button
4 OPTION button
Table of symbols
Wool
Super Quick
Extra Rinse
Start/Pause
Washing
Cotton
Spin
Handwash
Hygene Plus
5 Shirts
Rinses
Prewash
Economy
Synthetics
Delicates
Cold
Rinse Hold
Options
End
Easy Iron
Drain
Programme and temperature selector dials, spin speed button and available
options
Programme Selector Dial
It allows you to switch the appliance on/off and/
or to select a programme.
By selecting the position
wash with cold water.
the machine will
Available options:
Spin Reduction
By pressing this button you can change the spin
speed of the selected programme.
Temperature selector dial
This dial allows you to select the temperature
more suitable to the laundry to be washed.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
quantity of water (extra rinse), select this option.
Some additional rinses will be performed. This
option is recommended for people who are al-
lergic to detergents, and in areas where the water
is very soft.
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will be
necessary to empty out the water. To empty out
the water, please read the paragraph «At the end
of the programme».
Start Pause
This button allows you to start or to interrupt the
selected programme.
Easy Iron
By selecting this option the laundry is gently
washedandspuntoavoidanycreasing. Inthisway
ironing is easier. Furthermore the machine will
perform some additional rinses in some pro-
grammes. On cotton programmes the maximum
spin speed is reduced automatically.
Indicator pilot light (7)
The light 7.1 illumi-
nates after pressing
button 6 .
The light7.2 ison when
the machine is rinsing
or spinning phase.
The light 7.3 illumi-
nates at the end of the
washing cycle.
Super Quick
Short cycle for lightly soiled items or for laundry
which needs only freshening up. We recommend
you to reduce the fabrics loading.
Extra Rinse
This appliance is designed for saving energy. If it
necessary to rinse the laundry using an extra
First use
to activate the ECO valve. Then run a cotton
cycle at the highest temperature without any
laundry in the machine, to remove any manu-
facturing residue from the drum and tub. Pour
1/2 a measure of detergent into the main wash
compartment and start the machine.
• Ensure that the electrical and water con-
nections comply with the installation in-
structions.
• Remove the polystyrene block and any mate-
rial from the drum.
• Pour 2 liters of water into the main wash com-
partment
of the detergent drawer in order
Daily use
Load the laundry
Measure out the detergent and the fabric
softener
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in
the drum, one item at
a time, shaking them
out as much as possi-
ble. Close the door.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
rect option is selected, the integrated red pilot
light of the button 6 flashes for 3 times.
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent re-
quired, pour it into the main wash compart-
For the compatibility among the washing
programmes and the options see chapter
«Washing Programmes».
ment
or in the appropriate compartment if
the selected programme/option it requires
(see more details in "Detergent dispenser draw-
er").
Start the programme by pressing button 6
To start the selected programme, press the but-
ton 6 , the corresponding green pilot light stops
blinking. The appliance starts operating and the
only pilot light corresponding to the running
phase stays on.
If required, pour fabric softener into the com-
partment marked
(the amount used must
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
To interrupt a programme which is running, press
the button 6 : the corresponding green pilot light
starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 6
again .
Select the required programme by turning
the programme selector dial (1)
Turn the programme selector dial to the required
programme. The washing machine will automat-
ically select the maximum spin value provided for
theprogrammeyouhavechosen. Youcanchange
this value by pressing the corresponding button.
The green pilot light of the button 6 starts to
flash.
The selector dial can be turned either clockwise
or counterclockwise. Turn to position « O » to
reset programme/Switching the machine off.
At the end of the programme the selector dial
must be turned to position O, to switch the ma-
chine off.
If an incorrect option is selected, the red pilot
light of the button 6 blinks 3 times.
Altering an option or a running programme
It is possible to change some options before the
programme carries them out.
Before you make any change, you must PAUSE
the appliance by pressing the button 6 .
Changing a running programme is possible only
by resetting it. Turn the programme selector dial
to O and then to the new programme position.
Start the new programme by pressing the button
6 again. The washing water in the tub will be not
emptied out.
Caution! If you turn the programme
selector dial to another programme when
the machine is working, the red pilot light of
button 6 will blink 3 times to indicate a wrong
selection. The machine will not perform the new
selected programme.
Interrupting a programme
Press the button 6 to interrupt a programme
which is running, the corresponding green pilot
light starts blinking.
Select the required temperature by turning
the temperature selector dial (2)
Press the button again to restart the programme.
Turn clockwise this dial to select the more con-
venient to your laundry washing temperature.
Cancelling a programme
Turn the selector dial to « O » to cancel a pro-
gramme which is running. Now you can select a
new programme.
Select the available options by pressing
buttons 3, 4 and 5
Depending on the programme, different func-
tions can be combined. These must be selected
after choosing the desired programme and be-
fore starting the programme.
When these buttons are pressed, the corre-
sponding pilot lights illuminate. When they are
pressed again, the pilot lights go out. If an incor-
Opening the door
After the programme has started the door is
locked. If, for any reason, you need to open it, set
firstly the machine to PAUSE by pressing the but-
ton 6 . After a few minutes it will be possible to
open the door.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If the door remains locked, this means that the
luminates but the door remains locked to indi-
machine is already heating or that the water level cate that the water must be emptied out before
is too high. In any case, do not try to force the
door!
opening the door.
Follow the below instructions to empty out the
water:
If you cannot open the door but you need to
open it you have to switch the machine off by
turningtheselectordialtoO. Afterafewminutes
the door can be opened (pay attention to the
water level and temperature!) .
After closing the door, it is necessary to select
the programme and options again and to press
button 6 .
1. Turn the programme selector dial to O .
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by pressing
the relevant button.
4. Press button 6 .
At the end of the programme, the door can be
now opened. Turn the programme selector dial
to O to switch the machine off.
At the end of the programme
The machine stops automatically. The pilot light
of button 6 and the pilot light corresponding to
the just finished washing phase go off. The light
7.3 illuminates.
If a programme or an option that ends with water
left in the tub has been selected, the light 7.3 il-
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not in-
tend to carry out another wash, close the water
tap. Leave the door open to prevent the forma-
tion of mildew and unpleasant smells.
Helpful hints and tips
Blood: treat freshstainswithcoldwater. Fordried
stains, soak overnight in water with a special de-
tergent then rub in the soap and water.
Oil based paint: moisten with benzine stain re-
mover, lay the garment on a soft cloth and dab
the stain; treat several times.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain
with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damagedand the
fabric tends to hole.
Sorting out the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instruc-
tions. Sort the laundry as follows: whites, colour-
eds, synthetics, delicates, woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special deter-
gent or detergent paste.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
Grass: soap lightly and treat with bleach (whites
and fast coloureds only).
Treat curtains with special care. Remove hooks or
tie them up in a bag or net.
1)
Ball point pen and glue: moisten with acetone ,
lay the garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any re-
sidual marks with bleach.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat
any residual marks with bleach.
Removing stains
Stubborn stains may not be removed by just wa-
ter and detergent. It is therefore advisable to
treat them prior to washing.
1) do not use acetone on artificial silk
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ink: depending on the type of ink, moisten the
fabric first with acetone , then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methy-
lated spirits or benzine, then rub with detergent
paste.
Your appliance incorporates a recirculation sys-
tem which allows an optimal use of the concen-
trated detergent.
Follow the product manufacturer’s recommen-
dations on quantities to use and do not exceed
the«MAX»markinthedetergentdispenserdraw-
er .
1)
Quantity of detergent to be used
Detergents and additives
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Follow the product manufacturers’ instructions
on quantities to use.
Good washing results also depend on the choice
of detergent and use of the correct quantities to
avoid waste and protect the environment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset
the delicate balance of nature.
Use less detergent if:
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of soil-
ing.
All commonly available washing machine deter-
gents may be used in this appliance:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness isclassifiedinso-called“degrees”
of hardness. Information on hardness of the wa-
terinyourarea can be obtainedfrom therelevant
water supply company, or from your local au-
thority. If the water hardness degree is medium
or high we suggest you to add a water softener
following always the manufacturer’s instructions.
When the degree of hardness is soft, readjust the
quantity of the detergent.
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C
max) and woollens
• liquid detergents, preferably for low temper-
ature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent and any additives must be placed
in the appropriate compartments of the dispens-
er drawer before starting the wash programme.
If using liquid detergents, a programme without
prewash must be selected.
Washing Programmes
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
COTTON
90°-Cold
Main wash - Rinses
Maximum spin speed 800 rpm
Max. load 6 kg - Reduced load 3 kg
SPIN, RINSE HOLD,
EASY IRON , SUPER
QUICK, EXTRA RINSE
2)
1)
White and coloured cotton (normally soiled items).
3)
COTTON + PREWASH
90°-Cold
Prewash - Main wash - Rinses
Maximum spin speed 800 rpm
SPIN, RINSE HOLD,
EASY IRON , SUPER
QUICK, EXTRA RINSE
2)
1)
Max. load 6 kg - Reduced load 3 kg
White and coloured cotton (heavy soiled items).
4)
SPIN, RINSE HOLD,
EASY IRON , EXTRA
COTTON + ECO
90°-40°
2)
Main wash - Rinses
RINSE
Maximum spin speed 800 rpm
Max. load 6 kg
White and coloured cotton. This programme can be
selected for slightly or normally soiled cotton items.
The temperature will decrease and the washing time
will be extended. This allows to obtain a good washing
efficiency by saving energy.
4)
3)
SPIN, RINSE HOLD,
EASY IRON , EXTRA
COTTON + ECO + PREWASH
90°-40°
2)
Prewash - Main wash - Rinses
RINSE
Maximum spin speed 800 rpm
Max. load 6 kg
White and coloured cotton. This programme can be
selected for normally soiled cotton items. The tem-
perature will decrease and the washing time will be
extended. This allows to obtain a good washing effi-
ciency by saving energy.
SYNTHETICS
60°-Cold
Main wash - Rinses
Maximum spin speed 800 rpm for
Max. load 3 kg - Reduced load 1,5 kg
SPIN, RINSE HOLD,
EASY IRON , SUPER
QUICK, EXTRA RINSE
2)
1)
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
SYNTHETICS + PREWASH
60°-Cold
Prewash - Main wash - Rinses
Maximum spin speed 800 rpm
SPIN, RINSE HOLD,
EASY IRON , SUPER
QUICK, EXTRA RINSE
2)
1)
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
DELICATES
40°-Cold
Main wash - Rinses
Maximum spin speed 600 rpm
Max. load kg 3 - Reduced load 1,5 kg
SPIN, RINSE HOLD,
SUPER QUICK, EXTRA
RINSE
1)
Delicate fabrics: acrylics, viscose, polyester.
WOOL
SPIN, RINSE HOLD
40°-Cold
Main wash - Rinses
Maximum spin speed 800 rpm
Max. load 2 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fab-
rics. Note: A single orbulky item may causeimbalance.
If the appliance doesn’t perform the final spin phase,
add more items, redistribute the load manually and
then select the spinning programme.
HANDWASH
SPIN, RINSE HOLD
30°-Cold
Main wash - Rinses
Maximum spin speed 800 rpm
Max. load 2 kg
Special programme for delicate fabrics with «hand
washing» care symbol.
5 SHIRTS
SPIN
30°
Main wash - Rinses
Maximum spin speed 800 rpm
Max. load 1 kg
This programme is suitable for 5 - 6 lightly soiled shirts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
3)
HYGENE PLUS
90°-40°
Main wash - Rinses
Maximum spin speed 800 rpm
Max. load 6 kg
SPIN, RINSE HOLD,
EASY IRON , EXTRA
2)
RINSE
Hygiene plus cycle to sanitize cotton and synthetic
items. This programme eliminates the micro-organ-
isms thanks to the intensive washing and an additional
rinse. This action will be more efficient pouring into
the Prewash compartment a special sanitizing addi-
tive.
RINSES
Rinses
SPIN, RINSE HOLD,
EASY IRON , EXTRA
2)
Maximum spin speed 800 rpm
Max. load 6 kg
RINSE
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs 3 rinses, followed by a final long
spin. The spin speed can be reduced.
DRAIN
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in pro-
grammes with the Rinse Hold option selected.
SPIN
SPIN
Drain and long spin
Maximum spin speed 800 rpm
Max. load 6 kg
Separate spin for hand washed garments and after
programmes with the Rinse Hold option selected. You
can choose the spin speed by pressing the relevant
button to adapt it to the fabrics to be spun.
O = OFF
For cancelling the programme which is running or to switch the machine off .
1) If you select the Super Quick option by pressing button 4 , we recommend that you reduce the maximum load
as indicated. Full loading is possible however with somewhat reduced cleaning results.
2) Max. load with Easy iron option 1 kg
3) If using liquid detergents, a programme without PREWASH must be selected.
4) This programme is not active at a temperature lower than 40°C.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do if…
Certain problems are due to lack of simple main- Once the problem has been eliminated, press the
tenance or oversights, which can be solved easily button 6 to restart the programme. If after all
without calling out an engineer. Before contact- checks, the problem persists, contact your local
ing your local Service Centre, please carry out the Service Centre.
checks listed below.
During machine operation it is possible that the
red pilot light of button 6 blinks to indicate that
the machine is not working.
Problem
Possible cause/Solution
The door has not been closed (the button 6 red light blinks).
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The washing machine does not The main fuse has blown.
start:
• Replace the fuse.
The programme selector dial is not correctly positioned and the
button 6 has not been pressed.
• Please turn the selector dial and press the button 6 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay
start.
The water tap is closed (the button 6 red light blinks).
• Open the water tap.
The inlet hose is squashed or kinked (the button 6 red light blinks).
• Check the inlet hose connection.
The filter in the inlet hose is blocked (the button 6 red light blinks).
The machine does not fill:
• Clean the water inlet hose filter.
The door is not properly closed (the button 6 red light blinks).
• Close the door firmly.
The drain hose is squashed or kinked (the button 6 red light blinks).
• Check the drain hose connection.
The drain filter is clogged (the button 6 red light blinks).
• Clean the drain filter.
An option or a programme that ends with the water still in the tub
or a that eliminates all the spinning phases has been selected.
The machine does not empty
and/or does not spin:
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
There is water on the floor:
• Replace it with a new one.
The emergency emptying cap has not been replaced into the filter
cover or the filter has not been properly screwed in after cleaning
action.
• Refit the emergency emptying cap into the filter cover or screw
the filter fully in.
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Unsatisfactory washing results:
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
The door will not open:
• Wait a few minutes before opening the door.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
The machine vibrates is noisy:
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause/Solution
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not evenly distrib-
uted inthedrum, the machine will notspin. Inthiscase, redistribute
the load manually and select the spin programme.
Spinning starts late or the ma-
chine does not spin:
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
If you are unableto identifyorsolvetheproblem,
contact our service centre. Before telephoning,
make a note of the model, serial number and
purchase date of your machine: the Service Cen-
tre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
44 cm
Electrical connection
Information on the electrical connection is given on the rating
Voltage - Overall power - Fuse plate, on the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
6 kg
Maximum
800 rpm
Consumption values
Programme
Energy consumption Water consumption (li- Programme duration
(KWh)
tres)
(Minutes)
White Cottons 90°
Cottons 60°
2.1
62
140
1.3
59
130
1)
1.02
52
155
Cotton ECO 60°
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme
Cottons 40°
Energy consumption Water consumption (li- Programme duration
(KWh)
0.75
0.5
tres)
(Minutes)
59
125
80
70
60
Synthetics 40°
45
Delicates 40°
0.55
0.3
55
Wool/ Handwash 30°
50
1) «Cottons Eco» at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label,
in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary
depending on the quantity and type of laundry, on the inlet water temperature and on the
ambient temperature.
Care and cleaning
Warning! You must DISCONNECT the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
Remove the drawer by To aid cleaning, the
any laundry washing, and according to the soft-
pressing the catch
downwards and by
pulling it out. Flush it should be removed.
out under a tap, to re-
top part of the addi-
tive compartment
ening powder manufacturer's instructions. This
will help to prevent the formation of lime de-
posits.
External cleaning
move any traces of ac-
cumulated powder.
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the drawer recess
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Having removed the
drawer, use a small
brush to clean the re-
cess, ensuring that all
washing powder resi-
due is removed from
the upper and lower
part of the recess.
Replace the drawer and run the rinse pro-
gramme without any clothes in the drum.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Drain pump
The pump should be inspected regularly and par-
ticularly if:
Remove any objects
from the pump impel-
ler by rotating it.
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
Proceed as follows:
• disconnect the appliance.
• if necessary wait until the water has cooled
down.
Open the pump door
levering on the groove
with a coin (or with the
suitable tool, that you
can find in the bag
1
Replace the filter into the pump paying atten-
tion to insert it properly. When done, screw it
firmly.
containing the instruc-
tion booklet, depend-
ing on the model).
2
Replace the emergen-
cy emptying cap into
the filter cover and fix
it firmly.
Place a bowl with a
smalledgeclosetothe
pump to collect any
spillage.
Close the pump door.
Pull out the emergen-
cy emptying cap from
the filter cover, using a
pliers.
Warning! When the appliance is in use and
depending on the programme selected
When no more water
comes out, unscrew
the pump cover, using
a pliers, and remove
the filter. Always keep
a rag nearby to dry up
spillage of water when
removing the cover.
there can be hot water in the pump. Never
remove the pump cover during a wash cycle,
always wait until the appliance has finished the
cycle, and is empty. When replacing the cover,
ensure it is securely re-tightened so as to stop
leaks and young children being able to remove it.
2
1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the water inlet filter
Emergency emptying out
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged. It is therefore a good idea to clean it
from time to time.
If the water is not discharged, proceed as follows
to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled
down;
Turn off the water tap.
Unscrew the water in-
let hose. Clean the fil-
ter using a hard bristle
brush. Tighten up the
inlet hose.
• open the pump door;
• place a bowl on the floor. Remove the emer-
gency emptying cap from the filter. The water
should drain by gravity into the bowl. When
the bowl is full, refit the emergency emptying
cap into the filter. Empty the bowl. Repeat the
procedure until water stops flowing out;
Frost precaution
If the machine is exposed to temperatures below
0°C, certain precautions should be taken.
• clean the pump if necessary as previously de-
scribed;
• screw the pump cover again and close the
door.
• Turn off the water tap.
• Unscrew the inlet hose.
Important! Every time you drain the water
through the emergency emptying hose you must
pour 2 litres of water into the main wash
compartment of the detergent drawer and then
run the drain programme. This will activate the
ECO Valve device avoiding that part of the
detergent remains unused at next washing.
• Place the end of the inlet hose in a bowl placed
on the floor, open the emergency emptying
cap of the filter and let water drain out.
• Refit the emergency emptying cap into the fil-
ter and screw the water inlet hose back.
• Whenyouintendtostartthemachineupagain,
make sure that the room temperature is above
0°C.
Installation
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
After removing all the Remove the power
packaging, carefully
lay machine on it's
back to remove the
supply cable and the
hoses from the hose
holders on the rear of
polystyrene base from the appliance.
the bottom.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
If necessary, check the
setting with a spirit
level.
Unscrew the three
bolts.
Slide out the relevant
plastic spacers.
Water inlet
Warning! This appliance must be connected
to a cold water supply
Caution! Before connecting up the
appliance to new pipework or to pipework
that has not been used for some time, run off a
reasonable amount of water to flush out any
debris that may have collected
Caution! Do not use the hose from your
previous appliance to connect to water
supply.
Fill the smaller upper hole and the two large
ones with the corresponding plastic plug caps
supplied in the bag containing the instruction
booklet.
Connect the hose to a
tap with a 3/4” thread.
Always use the hose
supplied with the ap-
pliance.
Positioning
Install the machine on a flat hard floor. Make sure
that air circulation around the machine is not im-
peded by carpets, rugs etc. Check that the ma-
chine does not touch the wall or other kitchen
units. Level the washing machine by raising or
lowering the feet. The feet may be tight to adjust
as they incorporate a self locking nut, but the
machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
35°
45°
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar materials
under the machine to compensate for any un-
evenness in the floor.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The other end of the inlet hose which connects
to the appliance can be turned as showed in the
picture.
Do not place the inlet hose downwards. Angle
the hose to the left or right depending on the
position of your water tap. Set the hose cor-
rectly by loosening the ring nut. After position-
ing the inlet hose, be sure to tighten the ring
nut again to prevent leaks.
In this case, make sure the end cannot come
unhooked when the machine is emptying. This
could be done by tying it to the tap with a piece
of string or attaching it to the wall.
Caution! The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to purchase
anew, longerhosespeciallydesignedforthistype
of use.
In a sink drain pipe branch . This branch must be
above the trap so that the bend is at least 60
cm above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm. The end
of the drain hose must always be ventilated ,
i.e. the inside diameter of the drain pipe must
be larger than the outside diameter of the drain
hose. The drain hose must not be kinked.
Water drainage
The end of the drain hose can be positioned in
three ways:
Hooked over the edge
of a sink using the plas-
tic hose guide sup-
plied with the ma-
chine.
Electrical connection
Information on the electrical connection is given
on the rating plate on the inner edge of the ap-
pliance door.
any responsibility for damage or injury through
failure to comply with the above safety
precaution.
Check that your domestic electrical installation
can take the maximum load required, also taking
into account any other appliances in use.
Caution! The power supply cable must be
easily accessible after installing themachine.
Caution! Should the appliance power
supply cable need to be replaced, this must
be carried out by a Service Centre.
Caution! Connect the machine to an
earthed socket.
Caution! The manufacturer does not accept
Environment concerns
taken to the appropriate collection point for the
recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly,
The symbol
on the product or on its
packaging indicates that this product may not be
treated as household waste. Instead it should be
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Ecological hints
you will help prevent potential negative
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product. For
more detailed informationabout recycling of this
product, please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
• Normally soiled laundry may be washed with-
out prewashing in order to save detergent, wa-
ter and time (the environment is protected
too!).
• The machine works more economically if it is
fully loaded.
Packaging materials
The materials marked with the symbol
cyclable.
>PE<=polyethylene
>PS<=polystyrene
are re-
• With adequate pre-treatment, stains and limi-
ted soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water
hardness, the degree of soiling and the quan-
tity of laundry being washed.
>PP<=polypropylene
Thismeansthatthey canberecycled by disposing
of them properly in appropriate collection con-
tainers.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
web portal 1
web portal 2
Download from Www.Somanuals.com. All Manuals Search And Download.
|