EN
User manual
Washing Machine
ZWG 5120 P
ZWG 5140 P
Download from Www.Somanuals.com. All Manuals Search And Download.
• Install the appliance on a flat hard floor.
wards for gelatinous detergents, with programmes in-
cluding prewash, with the delay start option. In all
these cases you can use metering balls or sachets
provided with the detergent, Take out the metering
aid at the end of the washing cycle.
• Garments which have been in contact with volatile pe-
troleum products should not be machine washed. If
volatile cleaning fluids are used, care should be tak-
en to ensure that the fluid is removed from the gar-
ment before placing in the appliance.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug itself.
• Never use the appliance if the power supply cable,
the control panel, the working surface or the base are
damaged so that the inside of the appliance is acces-
sible.
• Never place cardboard, wood or similar materials un-
der the appliance to compensate for any unevenness
in the floor.
• If the appliance is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely
under the appliance.
• Check that the appliance does not touch the wall or
other kitchen units.
• This appliance must be connected to a cold water sup-
ply.
• Do not use the hose from your previous appliance to
connect to water supply. Always use the hose sup-
plied with the appliance.
• The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially de-
signed for this type of use.
• Always be sure, that there is no water leakage from
hoses and their connections after the installation.
• If the appliance is installed in a location subject to
frost, please read the “Frost precaution” chapter. Man-
ufacturer decline any responsibility for freezing dam-
ages.
Child safety
• This appliance is not intended for use by persons (in-
cluding children) with reduced physical sensory or
mental capabilities or lack of experience and knowl-
edge unless they have been given supervision or in-
struction concerning use of the appliance by a per-
son responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• The packaging components (e.g. plastic film, poly-
styrene) can be dangerous to children - danger of suf-
focation! Keep them out of children’s reach.
• Any plumbing work required to install this appliance
should be carried out by a qualified plumber or com-
petent person.
• Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb inside
the drum. To prevent children and pets becoming trap-
ped inside the drum this appliance incorporates a spe-
cial feature.
Use
• This appliance is designed for domestic use. It must
not be used for purposes other than those for which
it was designed.
• Only wash fabrics which are designed to be machine
washed. Follow the instructionsoneachgarmentlabel.
• Do not overload the appliance. See the "Washing Pro-
gramme Chart".
• Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
• The detergent dispenser drawer is provided with an
insert for liquid detergent. Do not use the insert down-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate this device, ro- To disable this device
tate the button (without
pressing it) inside the
and restore the possibili-
ty of closing the door, ro-
door clockwise until the tate the button anti-clock-
groove is horizontal. If
necessary use a coin.
wise until the groove is
vertical.
Frost precaution
If the appliance is installed in a place where the temper-
ature could drop below 0°C, proceed as follows to re-
move any water remaining inside the appliance:
1. unplug the appliance;
2. turn off the water tap;
5. place a bowl on the floor;
6. let the drain hose run along the floor, place the ex-
ternal extremities of the drain and inlet hoses in the
bowl placed on the floor and let water drain out com-
pletely;
7. screw the water inlet hose to the tap and the drain
hose to the rear of the appliance again;
When you intend to start the appliance up again, make
sure that the room temperature is above 0°C.
3. unscrew the water inlet hose from the tap;
4. unscrew the drain hose from the rear support and
unhook it from sink or spigot;
Environment concerns
please contact your local council, your household waste
disposal service or the shop where you purchased the
product.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more
detailed information about recycling of this product,
Packaging materials
The materials marked with the symbol
>PE<=polyethylene
are recyclable.
>PS<=polystyrene
>PP<=polypropylene
4
Download from Www.Somanuals.com. All Manuals Search And Download.
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
• The machine works more economically if it is fully
loaded.
• With adequate pre-treatment, stains and limited soil-
ing can be removed; the laundry can then be washed
at a lower temperature.
• Measure out detergent according to the water hard-
ness, the degree of soiling and the quantity of laun-
dry being washed.
Ecological hints
To save water, energy and to help protect the environ-
ment, we recommend that you follow these tips:
• Normally soiled laundry may be washed without pre-
washing in order to save detergent, water and time
(the environment is protected too!).
Product description
7
1
2
3
11
8
9
9
4
5
9
10
12
6
1
2
3
4
5
6
7
8
9
10
11
12
Detergent dispenser drawer
Worktop
Control panel
Door opening handle
Rating plate (on the inner edge)
Front adjustable feet
Water drain hose
Drain hose support
Hose holders
Water inlet hose
Mains cable
Back feet
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
50 cm
Electrical connection
Information on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
6 kg
Maximum
1200 rpm (ZWG5120P)
1400 rpm (ZWG5140P)
Installation
Unpacking
Warning!
• Read carefully the "Safety information" chap-
ter before installing the appliance.
x 3
• Remove the cardboard top.
• Remove the polystyrene packaging materials.
A
B
x 3
x 1
• Spread the front piece
on the floor behind the
C
x 2
1
appliance and then lay
the appliance carefully
rear side down on it.
Make sure that no ho-
ses are crushed in the
process.
Warning! Remove and keep all transit devices
so that they can be refitted if the appliance ever
2
has to be transported again.
Necessary tools
• Remove the polystyrene base from the bottom.
• Return appliance to
it's upright position.
10 mm
30 mm
• Remove the external
film. Use a cutter, if
necessary.
• Open the door and re-
move the plastic hose
guide, the bag contain-
ing the instruction
booklet and the plastic
plug caps from the
drum.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• Remove the power supply cable and the draining
and inlet hose from the hose holders ( C ) on the
rear of the appliance.
• Plug the smaller upper hole and the two large ones
with the corresponding plastic plug caps.
Positioning and levelling
• Unscrew the three bolts ( A ) and remove the hose
holders ( C ).
• Slide out the relevant plastic spacers ( B ).
x 4
Level the appliance by raising or lowering the feet.
The appliance MUST be level and stable on a flat
hard floor. If necessary, check the setting with a spirit
level. Any necessary adjustment can be made with a
spanner.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Firstly form a hook in the end of the drain hose using
the plastic hose guide supplied with the appliance .
The end of the drain hose can be positioned in three
ways:
• Hooked over the edge of a sink using the plastic
hose guide.
Accurate levelling prevents vibration, noise and dis-
placement of the appliance during operation.
Repeat the levelling action, if the appliance is not lev-
el and stable.
Water inlet
Tie the plastic hose guide to the tap with a string to
prevent that the drain hose unhooks when the appli-
ance is emptying.
Connect the hose to a tap
with a 3/4” thread.
• Onto a sink outlet spigot.
35°
45°
Push the drain hose onto the spigot and secure with a
clip, ensure a loop is formed in the drain hose to pre-
vent waste from the sink entering the appliance.
Loosen the ring nut to angle the hose to the left or
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
right depending on the position of your water tap. Do
not place the inlet hose downwards. After positioning
the inlet hose, be sure to tighten the ring nut again to
prevent leaks.
• Directly into a drain pipe at a height of not less
than 60 cm and not more than 100 cm.
The end of the drain hose
must always be ventila-
ted , i.e. the inside diame-
ter of the drain pipe must
be larger than the outside
diameter of the drain
Water drainage
hose. The drain hose
must not be kinked.
• Directly to a built-in drain pipe in the room wall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The drain hose may be extended to a maximum of
4 metres. An additional drain hose and joining
piece is available from your Local Centre.
Connections overview
115 cm
140 cm
9 0 cm
115 cm
100 cm
150 cm
• Make sure that the mains plug and cable is not squash-
ed or damaged by the back of the appliance.
• Make sure that the mains plug is accessible after in-
stallation.
• Do not pull the mains cable to disconnect the appli-
ance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.
Electrical connection
• The appliance must be earthed.
• Make sure that the electrical information on the rat-
ing plate agree with your domestic power supply.
• Always use a correctly installed shockproof socket.
• Do not use multi-way plugs, connectors and exten-
sion cables. There is a risk of fire.
• Do not replace or modify the mains cable yourself.
Contact the After Sales Service.
First use
• Ensure that the electrical and water connec-
tions comply with the installation instructions.
machine, to remove any manufacturing residue
from the drum and tub. Pour 1/2 a measure of
detergent into the main wash compartment and
start the machine.
• Ensure that the drum is empty.
• Before the first wash, run a cotton cycle at the
highest temperature without any laundry in the
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Daily use
1)
Sort out the laundry
Ball point pen and glue : moisten with acetone , lay the
garment on a soft cloth and dab the stain.
Lipstick : moisten with acetone as above, then treat
stains with methylated spirits. Treat any residual marks
with bleach.
Red wine : soak in water and detergent, rinse and treat
with acetic or citric acid, then rinse. Treat any residual
marks with bleach.
Follow the wash code symbols on each garment label
and the manufacturer’s washing instructions. Sort the
laundry as follows: whites, coloureds, synthetics, deli-
cates, woollens.
Before Loading The Laundry
Important! Make sure that
no metal objects are left
in the laundry (e.g. hair
clips, safety pins, pins).
Button up pillowcases,
close zip fasteners, hooks
and poppers. Tie any
belts or long tapes. Re-
move any hooks (e.g cur-
tains).
Ink : depending on the type of ink, moisten the fabric
first with acetone , then with acetic acid; treat any resid-
ual marks on white fabrics with bleach and then rinse
thoroughly.
Tar stains : first treat with stain remover, methylated spi-
rits or benzine, then rub with detergent paste.
1)
Open the door by carefully pulling the door handle
outwards
Load the laundry
• Never wash whites and coloureds together. Whites
may lose their «whiteness» in the wash.
• New coloured items may run in the first wash; they
should therefore be washed separately the first time.
• Rub particularly soiled areas with a special detergent
or detergent paste.
Place the laundry in the
drum, one item at a time,
shaking them out as
much as possible.
• Treat curtains with special care.
• Wash the socks and the gloves inside the bag or a net.
Remove stubborn stains before washing:
Blood : treat fresh stains with cold water. For dried
stains, soak overnight in water with a special detergent
then rub in the soap and water.
Oil based paint : moisten with benzine stain remover,
lay the garment on a soft cloth and dab the stain; treat
several times.
Maximum Loads
Recommended loads are indicated in the «Wash-
ing Programmes».
General rules:
Dried grease stains : moisten with turpentine, lay the gar-
ment on a soft surface and dab the stain with the finger-
tips and a cotton cloth.
Rust : oxalic acid dissolved in hot water or a rust remov-
ing product used cold. Be careful with rust stains which
are not recent since the cellulose structure will already
have been damaged and the fabric tends to hole.
Mould stains : treat with bleach, rinse well (whites and
fast coloureds only).
• Cotton, linen : drum full but not too tightly packed;
• Synthetics : drum no more than half full;
• Delicate fabrics and woollens : drum no more than
one third full.
Grass : soap lightly and treat with bleach (whites and
fast coloureds only).
1) do not use acetone on artificial silk.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
If the water hardness degree is medium or high we sug-
gest you to add a water softener following always the
manufacturer’s instructions.
When the degree of hardness is soft, readjust the quan-
tity of the detergent.
Close the door gently
Warning! Make
sure that any fab-
rics were not trapped
when closing the door.
Open the detergent dispenser drawer
Compartment for
powder or liquid deter-
gent used for main
wash.
Compartment
Detergents and additives
for liquid additives (fabric
softener, starch).
Good washing results also depend on the choice of de-
tergent and use of the correct quantities to avoid waste
and protect the environment.
Although biodegradable, detergents contain substances
which, in large quantities, can upset the delicate bal-
ance of nature.
Warning! If you wish to carry out the prewash,
pour the detergent among washing items into the
The choice of detergent will depend on the type of fabric
(delicates, woollens, cottons, etc.), the colour, washing
temperature and degree of soiling.
All commonly available washing machine detergents
may be used in this appliance:
drum.
Warning! Depending on the type detergent you
use (powder of liquid), ensure that the flap, placed
in the main wash compartment, is in the desired position.
• powder detergents for all types of fabric,
Flap for powder or liquid detergent
• powder detergents for delicate fabrics (40°C max)
and woollens,
• liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of fabric,
or special for woollens only.
UP- Flap position if us-
ing POWDER detergent
DOWN - Flap position if
using LIQUID detergent
during main wash
Quantity of detergent to be used
The type and quantity of detergent will depend on the
type of fabric, load size, degree of soiling and hardness
of the water used.
For the quantity of detergent, refer always to what is writ-
ten on the product packing.
Use less detergent if:
• you are washing a small load,
If the flap is not in the desired position :
• the laundry is lightly soiled,
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in your
area can be obtained from the relevant water supply com-
pany, or from your local authority.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
• Remove the drawer. Push the drawer edge out-
wards where indicated by the arrow (PUSH) to fa-
cilitate drawer removal.
•
Pour the liquid detergent in the compartment
without exceeding the limit indicated in the flap.
The detergent must be placed in the appropriate
compartments of the dispenser drawer before start-
ing the wash programme.
The flap is down and you wish to use powder detergent:
• Rotate the flap up-
wards. Ensure to fit the
flap completely in.
• Carefully put the draw-
er back.
Warning! Do not use the flap in "DOWN" position
with:
• Gelatinous detergent or thick detergent.
• Powder detergent.
• With programmes with prewash.
• Do not use liquid detergent if the washing pro-
gramme doesn't start immediately.
• Measure out the deter-
gent.
• Pour the powder deter-
gent into the main
wash compart-
In all above listed cases, use the flap in "UP" posi-
tion .
Measure out the fabric softener
ment
.
Pour fabric softener or
any additives into the
compartment marked
(do not exceed the
«MAX» mark in the draw-
er). Any additives must
be placed in the appropri-
ate compartments of the
dispenser drawer just be-
fore starting the wash pro-
gramme.
The flap is up and you wish to use liquid detergent:
• Rotate the flap down-
wards.
• Carefully put the draw-
er back.
Close the detergent dispenser drawer
• Measure out the detergent.
For the quantity of detergent, refer always to
what is written on the product packing and en-
sure that the detergent can be poured in the drawer.
Set your washing programme
The control panel permits to select a washing programmes and different options.
When an option button is selected, the corresponding pilot light is on. Otherwise it is off.
For compatibility among washing programmes and options, see the "Washing Programme Chart". If an in-
correct option is selected, the integrated red pilot light of the button 6 flashes 3 times.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Speciaal
Spécial
Katoen
Coton
Temp.
Jeans
+Voorwas
+Prélavage
Mini 30
20°
1400
900
7.1
7.2
7.3
Hemden
Zuinig
Eco
Hoofdwas
Chemises
4H
8H
Lavage
Extra spoelen
Rinçage plus
700
Antikreuk
Repassage facile
Synthetisch
Synthétique
Einde
30°
Fin
90°
Start/Pauze
Départ/Pause
Supersnel
Startuitstel
Départ différé
Centrifugeren
Essorage
Centrifugeren
Essorage
Mix
Rapide
40°
Pompen
Vidange
Fijne was
Délicats
60°
Wol/Laine
Spoelen
Rinçage
Handwas
Lavage à la main
1
2
3
4
5
6
Turn the programme selector dial to the required programme. The selec-
tor dial can be turned either clockwise or counter-clockwise. The green
pilot light of the button 6 starts flashing: the appliance is now switched on.
Programme selector dial
If you turn the programme selector dial to another programme
when the appliance is working, the red pilot light of the button 6
will flash 3 times to indicate a wrong selection. The appliance will not
perform the new selected programme.
Speciaal
Spécial
Katoen
Coton
Jeans
+Voorwas
+Prélavage
Mini 30
Hemden
Zuinig
Eco
Chemises
1
Antikreuk
Repassage facile
Synthetisch
Synthétique
• To switch the appliance off , turn the programme selector dial to the
Centrifugeren
Mix
Essorage
Pompen
Vidange
Fijne was
Délicats
position
• To cancel or change a running programme, switch the appliance off
by turning the programme selector dial to the position . Select the
.
Wol/Laine
Spoelen
Rinçage
Handwas
Lavage
à
la main
new programme by turning the selector to the desired programme.
Start the new programme by pressing the button 6 again. The water in
the tub will be not emptied out.
Temperature knob
Temp.
20°
Turn clockwise this dial to select the most suitable temperature for wash-
2
ing your laundry .
30°
Cold : Cold wash.
90°
40°
60°
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Spin Reduction
By selecting a programme, the appliance proposes automatically the max-
imum spin speed provided for that programme.
Press this button repeatedly to change the spin speed, if you want your
laundry to be spun at a different speed. The relevant light illuminates.
Rinse Hold
By selecting this function the water of the last rinse is not emptied out to
prevent the fabrics from creasing. Before opening the door it will be nec-
essary to empty out the water.
1400
900
700
3
Centrifugeren
Essorage
To empty out the water, please read the paragraph «At the end of the pro-
gramme».
The start of the programme can be delayed by 8 or 4 hours by means of
this button. The relevant light illuminates.
You must select this option after you have set the programme and before
you start the programme.
Select a delayed start:
• select the programme and the required options;
• select the delay start by pressing the button 4 ;
• press the button 6 :
Delay Start
4H
– the appliance starts its hourly countdown.
– The programme will start after the selected delay has expired.
Cancelling the delayed start after having started the programme:
8H
4
Startuitstel
Départ différé
• set the appliance to PAUSE by pressing the button 6 ;
• press the button 4 once, the light relevant to the selected delay goes off;
• press the button 6 again to start the programme.
The DELAY START cannot be selected with the drain programme.
Important! The selected delay can be changed only after selecting the
washing programme again. The door will be locked throughout the delay
time. If you need to open the door, you must set the appliance to PAUSE
(by pressing the button 6 ) and then wait a few minutes. After you have
closed the door, press the button 6 again.
Super Quick
By pressing this button the corresponding pilot light illuminates.
Short cycle for lightly soiled items or for laundry which needs only fresh-
ening up.
Supersnel
5
Rapide
With this option, a reduced load of laundry is recommended:
• Cottons 3 Kg
• Synthetics and delicates 1,5 Kg
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Extra Rinse
This appliance is designed for saving water. However, for people with
very delicate skin (allergic to detergents) it may be necessary to rinse the
laundry using an extra quantity of water.
Supersnel
Rapide
Startuitstel
Départ différé
Press simultaneously the buttons 4 and 5 for some seconds: the pilot
light 7.2 comes on. This function stays permanently on. To remove it
press the same buttons again until the pilot light 7.2 goes off.
Start the programme by pressing the button 6
• To start the selected programme, press the button 6 , the correspond-
ing green pilot light stops flashing. The pilot light 7.1 illuminates to
indicate that the appliance starts operating and the door is locked. If
you have chosen a delayed start, the appliance will begin the countdown.
• To interrupt a programme which is running, press the button 6 : the
corresponding green pilot light starts flashing. It is possible
to change some options of a running programme before the pro-
gramme carries them out.
• To restart the programme from the point at which it was interrupted,
press the button 6 .
Start/Pause
Start/Pauze
Départ/Pause
6
• After the programme has started the door is locked. If, for any reason,
you need to open the door , set firstly the appliance to PAUSE by press-
ing the button 6 . After a few minutes it will be possible to open the door.
If the door remains locked, this means that the appliance is already
heating or that the water level is too high. In any case, do not try to
force the door!
If you cannot open the door but you need to open it you have to
switch the appliance off by turning the selector dial to
. After a few
minutes the door can be opened ( pay attention to the water level and
temperature! ). After closing the door, it is necessary to select the pro-
gramme and options again and to press the button 6 .
Indicator pilot lights
• When you start the programme by pressing the button 6 , the washing
phase pilot light ( 7.1 ) illuminates. This means that the appliance is
operating.
• The additional rinses pilot light ( 7.2 ) illuminates when the appliance
perform an extra rinse.
7.1
7.2
7.3
Hoofdwas
Lavage
Extra spoelen
Rinçage plus
Einde
Fin
• When the programme has finished the end cycle pilot light ( 7.3 )
comes on.
If a programme or an option that ends with water left in
the tub has been selected and the door remains locked
to indicate that the water must be emptied out before
opening the door.
At the end of the programme
The appliance stops automatically. The pilot light of the
button 6 and the pilot light corresponding to the just fin-
ished washing phase go off. The light 7.3 illuminates.
Follow the below instructions to empty out the water:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Turn the programme selector dial to
.
lector dial and any button are not touched, after a few
minutes the energy saving system is enabled. The pilot
lights go off. The green pilot light of the button 6 flash-
es with a low frequency. By pressing any button the ap-
pliance will come out of the energy saving status.
• Select the draining or spinning programme.
• Reduce the spin speed if needed, by pressing the rel-
evant button.
• Press the button 6 .
At the end of the programme, the door can be now
Door seal
opened. Turn the programme selector dial to
switch the appliance off.
to
At the end of every cycle,
check from the door seal
and remove objects that
could be trapped in the
fold.
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open
to prevent the formation of mildew and unpleasant smells.
Warning! If there are children or pets in the
house, activate the child safety device in the inner
side of the door frame (for more details read " Child safe-
ty" in the chapter "Safety Information").
Stand by : during programme setting up and once
the programme has finished, if the programme se-
Washing programmes
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Com-
partment
Options
COTTONS
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
SUPER QUICK ,
EXTRA RINSE
90°-
(Cold)
Main wash - Rinses - Maximum spin speed: 1200 rpm for
ZWG5120P and 1400 rpm for ZWG5140P
Max. load 6 kg - Reduced load 3 kg
1)
White, coloured cotton and linen . Normally soiled items.
COTTONS + PREWASH
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
SUPER QUICK ,
EXTRA RINSE
90° -
(Cold)
Prewash - Main wash - Rinses - Maximum spin speed: 1200
rpm for ZWG5120P and 1400 rpm for ZWG5140P
Max. load 6 kg - Reduced load 3 kg
1)
White, coloured cotton and linen . Heavy soiled items.
ECO
60° - 40°
Main wash - Rinses - Maximum spin speed: 1200 rpm for
ZWG5120P and 1400 rpm for ZWG5140P
Max. load 6 kg
White and coloured cotton . This programme can be selected for
slightly or normally soiled cotton items. The temperature will de-
crease and the washing time will be extended. This allows to ob-
tain a good washing efficiency by saving energy.
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
EXTRA RINSE
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Com-
partment
Options
SYNTHETICS
60° -
(Cold)
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
SUPER QUICK ,
EXTRA RINSE
Main wash - Rinses - Maximum spin speed: 1200 rpm for
ZWG5120P - 900 rpm forZWG5140P
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics : underwear, coloured garments, non-
shrink shirts, blouses . Normally soiled items.
1)
MIX
20°
Main wash - Rinses - Maximum spin speed: 1200 rpm for
ZWG5120P - 900 rpm for ZWG5140P
Max. load 3 kg
Highly energy efficient cold wash programme for lightly soiled
laundry. This programme requires a detergent which is active in
cold water.
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
EXTRA RINSE
DELICATES
40°-
(Cold)
RINSE HOLD ,
DELAY START ,
SUPER QUICK ,
EXTRA RINSE
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load kg 3 - Reduced load 1,5 kg
Delicate fabrics : acrylics, viscose, polyester . Normally soiled
items.
1)
WOOL -
40°- (Cold)
HANDWASH
Main wash - Rinses - Maximum spin speed at 1200 rpm for
ZWG5120P - 900 rpm for ZWG5140P
Max. load 2 kg
Machine washable wool, hand washable woollens and delicate
fabrics with «hand washing» care symbol . Note : A single or bul-
ky item may cause imbalance. If the appliance doesn’t perform
the final spin phase, add more items, redistribute the load man-
ually and then select the spinning programme.
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START
RINSE
Rinse - Short spin speed 700 rpm. If a spin speed higher than
700 rpm is selected, by pressing the relevant button, the appli-
ance performs a long spin. (Maximum spin speed: 1200 rpm for
ZWG5120P and 1400 rpm for ZWG5140P)
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
EXTRA RINSE
Max. load 6 kg
To rinse and spin cotton garments which have been washed by
hand. Select the EXTRA RINSE option to intensify the rinsing ac-
tion. The appliance adds additional rinses.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load -
Type of Laundry
Detergent Com-
partment
Options
DRAIN
Draining of water
For emptying out the water left in the drum.
SPIN
Drain and long spin at maximum spin speed: 1200 rpm for
ZWG5120P- 1400 rpm for ZWG5140P
Max. load 6 kg
For emptying out the water left in the drum in the programmes
with Rinse Hold option.
SPIN REDUCTION ,
DELAY START
If a spin speed at 700 rpm or lower is selected, by pressing the
relevant button, the appliance performs a short spin.
EASY IRON
40°-
(Cold)
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START ,
EXTRA RINSE
Main wash - Rinses - Maximum spin speed at 900 rpm
In order to obtain the best anti-creasing result, reduce the load of
synthetic items. (Recommended load 1 kg)
Synthetic or mixed fabrics. Gentle wash and spin to avoid any
creasing. The appliance performs additional rinses.
SHIRTS
30°
SPIN REDUCTION ,
DELAY START
Main wash - Rinses - Maximum spin speed at 900 rpm
Synthetics and mixed fabrics . Suitable for 5 - 6shirts lightly soiled.
MINI 30
30°
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load 3 kg
DELAY START
Synthetics and delicates. Lightly soiled items or which only
needs freshening up.
JEANS
60°-
(Cold)
SPIN REDUCTION ,
RINSE HOLD ,
DELAY START
Main wash - Rinses - Maximum spin speed:1200 rpm for
ZWG5120P - 900 rpm for ZWG5140P
Max. load 3 kg
Trousers, shirts or jackets in denim and jersey realized with hi-
tech materials. The Extra Rinse option is activated automatically.
1) If you select the SUPER QUICK option by pressing button 5 , we recommend that you reduce the maximum load as indicated.
Full loading is possible however with somewhat reduced cleaning results.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption values
Programme
Energy consumption
(KWh)
Water consumption (litres) Programme duration (Mi-
nutes)
White Cottons 90°
Cottons 60°
2.10
1.20
1.02
78
72
49
175
170
180
1)
Cotton ECO 60°
Cottons 40°
0.75
0.60
0.60
0.30
72
57
65
48
145
95
75
Synthetics 40°
Delicates 40°
Wool/ Handwash 30°
55
1) «Cottons Eco» at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label, in compliance
with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Care and cleaning
Warning! Switch the appliance off and remove
the mains plug from the socket before any clean-
ing action.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
To run a maintenance wash:
• Remove the drawer.
• To aid cleaning, the
top part of the additive
compartment should
be removed.
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must be a pow-
der with biological properties.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
• open the filter cover by
pressing the special
hook and by rotating
the cover upwards;
Warning! Keep the
filter cover open un-
til the filter removal.
• before removing the fil-
ter, remove any fluff or
small objects from
• Use a stiff brush to clean and remove all washing
powder residue.
• Clean all the removed parts of the dispenser draw-
er under a tap to remove any traces of accumulated
powder.
around the filter;
• Use the previous
brush to clean the re-
cess, ensuring that up-
per and lower part of it
is well cleaned.
After having cleaned the dispenser and the drawer re-
cess, replace it.
• remove the filter and clean it under the tap;
Cleaning the drain filter
The filter permits to hold fluff or foreign bodies left un-
awares in the laundry.
The pump must be cleaned regularly.
To clean the filter, proceed as follows:
• if necessary, place the
filter cover in the right
position again.
• open the filter cover
and insert the filter
again;
•
turn programme selector dial to position
;
• unplug the appliance;
• open the door;
• turn the drum and
align the filter cover
( FILTER ) with the ar-
row on the door seal;
20
Download from Www.Somanuals.com. All Manuals Search And Download.
the display (if available) shows the relevant alarm (see
chapter "What to do if..." for more details), check if the
water inlet filters are blocked .
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose
from the tap.
• Clean the filter in the
hose with a stiff brush.
• Screw the hose back onto the tap. Make sure the
connection is tight.
• Unscrew the hose
from the appliance.
Keepatowelnearbybe-
cause some water may
flow.
• Clean the filter in the
valve with a stiff brush
or with the piece of
cloth.
The filter is inserted correctly when the indicator on
its top is visible and blocked.
• close the filter cover;
• insert the mains plug
again.
• Screw the hose back to the appliance and make
sure the connection is tight.
• Turn on the water tap.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, it takes a long
time to fill with water, the starting button flashes red or
What to do if…
The appliance does not start or stops during operation.
Certain problems are due to lack of simple maintenance
or oversights, which can be solved with the help of the
indications described in the charts, without calling out
an engineer.
pilot lights illuminates to indicate that the appliance is
not working.
Before contacting your local Service Centre, please car-
ry out the checks listed below.
During appliance operation it is possible that the red pi-
lot light of the button 6 flashes and one of the indicator
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault code and malfunction
Possible cause / Solution
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
Hoofdwas
Lavage
Extra spoelen
Rinçage plus
Einde
Fin
Start/Pauze
Départ/Pause
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked.
• Clean the water inlet filters (read "Cleaning the water inlet filters" for more details).
The light of button 6 flashes
and the light 7.1 illuminates:
Problem with the water supply
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
If the appliance stops working without discharging the water , first carry out an
emergency drain:
•
turn the programme selector dial to
;
Hoofdwas
Lavage
Extra spoelen
Rinçage plus
• unplug the appliance;
• close the water tap;
• if necessary, wait until the water has cooled down;
Einde
Fin
Start/Pauze
Départ/Pause
• unscrew the drain hose from the rear support (see "Frost precaution") and un-
hook it from the sink or spigot;
• let it run along the floor;
The light of button 6 flashes
and the light 7.2 illuminates:
Problem with the water drain-
age
• place a bowl on the floor and place the end of the draining hose into the bowl.
The water should drain by gravity into the bowl. When the bowl is full, empty
it. Repeat the procedure until water stops flowing out ;
• screw the draining hose to the rear support and reposition it;
• open the door and remove the laundry;
• carry out the drain filter cleaning as described in "Cleaning the drain filter";
• at the end of cleaning action, close the door and insert the mains plug again;
• run a drain programme to check if the appliance works now.
The door has not been closed or is not closed properly.
• Close firmly the door.
Hoofdwas
Lavage
Extra spoelen
Rinçage plus
Einde
Fin
Start/Pauze
Départ/Pause
The light of button 6 flashes
and the light 7.3 illuminates:
Door open
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The appliance does not start or stops during operation
without any visible alarm.
Before contacting your local Service Centre, please car-
ry out the checks listed below.
Malfunction
Possible cause / Solution
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
The appliance does not start:
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 6 has not
been pressed.
• Please turn the selector dial and press the button 6 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The end of the drain hose is too low.
• Refer to paragraph in "Water drainage" in chapter "Installation".
The appliance fills then emp-
ties immediately:
An option or a programme that ends with the water still in the tub or a that elimi-
nates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
The appliance does not emp-
ty and/or does not spin:
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not al-
ways easy to see this as the water runs down the hose; check to see if it is damp.
There is water on the floor:
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door lock is released.
There is water in the drum.
The door will not open:
• Select drain or spin programme to empty out the water.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Malfunction
Possible cause / Solution
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The appliance is not levelled correctly.
The appliance vibrates noisi- • Adjust the feet.
ly:
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in because the laundry is not
evenly distributed in the drum. The laundry is redistributed by reverse rotation of
the drum. This may happen several times before the unbalance disappears and nor-
mal spinning can resume. If, after 10 minutes, the laundry is still not evenly dis-
tributed in the drum, the appliance will not spin. In this case, redistribute the load
manually and select the spin programme.
Spinning starts late or the ap-
pliance does not spin:
• Load more laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the spinning
programme.
No water is visible in the
drum:
Appliances based on modern technology operate very economically using very lit-
tle water without affecting performance.
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
Unsatisfactory washing re-
sults
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The appliance is fitted with a type of motor which makes an unusual noise com-
The appliance makes an un- pared with other traditional motors. This new motor ensures a softer start and
usual noise
more even distribution of the laundry in the drum when spinning, as well as in-
creased stability of the appliance.
After completing these checks, switch on the appliance
and press the button 6 to restart the programme.
If the malfunction shows again, contact your Service Cen-
tre.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The necessary data for the service centre is on the rat-
ing plate. We recommend that you write the data here:
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Model description
(MOD.)
...............................
Product number (PNC) ...............................
Serial number (S.N.) ...............................
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|