Zanussi Refrigerator ZBA7190A User Manual

EN  
User manual  
Refrigerator  
2
ZBA7190A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
or damaged power plug may overheat and cause  
a fire.  
Report possible damages immediately to the place you  
bought it. In that case retain packing.  
3. Make sure that you can come to the mains plug of • It is advisable to wait at least four hours before con-  
the appliance.  
4. Do not pull the mains cable.  
necting the appliance to allow the oil to flow back in  
the compressor.  
• Adequate air circulation should be around the appli-  
ance, lacking this leads to overheating. To achieve  
sufficient ventilation follow the instructions relevant to  
installation.  
• Wherever possible the back of the product should be  
against a wall to avoid touching or catching warm parts  
(compressor, condenser) to prevent possible burn.  
• The appliance must not be located close to radiators  
or cookers.  
• Make sure that the mains plug is accessible after the  
5. If the power plug socket is loose, do not insert the  
power plug. There is a risk of electric shock or fire.  
6. You must not operate the appliance without the  
1)  
lamp cover of interior lighting.  
• This appliance is heavy. Care should be taken when  
moving it.  
• Do not remove nor touch items from the freezer com-  
partment if your hands are damp/wet, as this could  
cause skin abrasions or frost/freezer burns.  
• Avoid prolonged exposure of the appliance to direct  
sunlight.  
installation of the appliance.  
2)  
Connect to potable water supply only.  
Daily use  
Service  
• Do not put hot pot on the plastic parts in the appliance.  
• Do not store flammable gas and liquid in the appliance,  
because they may explode.  
• Appliance's manufacturers storage recommendations  
should be strictly adhered to. Refer to relevant instruc-  
tions.  
• Any electrical work required to do the servicing of the  
appliance should be carried out by a qualified electri-  
cian or competent person.  
• ThisproductmustbeservicedbyanauthorizedService  
Centre, and only genuine spare parts must be used.  
Environment Protection  
Care and cleaning  
Thisappliancedoesnot containgasseswhichcould  
damage the ozone layer, in either its refrigerant cir-  
cuit or insulation materials. The appliance shall not be  
discarded together with the urban refuse and rubbish. The  
insulation foam contains flammable gases: the appliance  
shall be disposed according to the applicable regulations  
to obtain from your local authorities. Avoid damaging the  
cooling unit, especially at the rear near the heat exchang-  
er. The materials used on this appliance marked by the  
• Before maintenance, switch off the appliance and dis-  
connect the mains plug from the mains socket.  
• Do not clean the appliance with metal objects.  
• Regularly examine the drain in the refrigerator for de-  
frosted water. If necessary, clean the drain. If the drain  
is blocked, water will collect in the bottom of the ap-  
pliance.  
Installation  
symbol  
are recyclable.  
Important! For electrical connection carefully follow the  
instructions given in specific paragraphs.  
• Unpack the appliance and check if there are damages  
on it. Do not connect the appliance if it is damaged.  
Operation  
Turn the Temperature regulator clockwise to a medium  
setting.  
Switching on  
Insert the plug into the wall socket.  
1) If the lamp cover is foreseen  
2) If a water connection is foreseen  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
• room temperature  
Switching off  
• how often the door is opened  
• the quantity of food stored  
• the location of the appliance.  
To turn off the appliance, turn the Temperature regulator  
to the "O" position.  
Temperature regulation  
The temperature is automatically regulated.  
To operate the appliance, proceed as follows:  
• turn the Temperature regulator toward lower settings  
to obtain the minimum coldness.  
• turn the Temperature regulator toward higher settings  
to obtain the maximum coldness.  
Important! If the ambient temperature is high or the  
appliance is fully loaded, and the appliance is set to the  
lowest temperatures, it may run continuously causing  
frost to form on the rear wall. In this case the dial must be  
set to a higher temperature to allow automatic defrosting  
and therefore reduced energy consumption.  
A medium setting is generally the most suitable.  
However, the exact setting should be chosen keeping in  
mind that the temperature inside the appliance depends  
on:  
First use  
Cleaning the interior  
Important! Do not use detergents or abrasive powders,  
as these will damage the finish.  
Before using the appliance for the first time, wash the  
interior and all internal accessories with lukewarm water  
and some neutral soap so as to remove the typical smell  
of a brand-new product, then dry thoroughly.  
Daily use  
Movable shelves  
Positioning the door shelves  
The walls of the refrigera-  
tor are equipped with a  
series of runners so that  
the shelves can be posi-  
tioned as desired.  
To permit storage of food  
packages of various sizes,  
the door shelves can be  
placed at different heights.  
Gradually pull the shelf in  
the direction of the arrows  
until it comes free, then  
reposition as required.  
Helpful hints and tips  
• If the ambient temperature is high and the Temperature  
Regulator is set to low temperature and the appliance  
is fully loaded, the compressor may run continuously,  
causing frost or ice on the evaporator. If this happens,  
Hints for energy saving  
• Do not open the door frequently or leave it open longer  
than absolutely necessary.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
set the Temperature Regulator toward warmer settings For safety, store in this way only one or two days at the  
to allow automatic defrosting and so a saving in elec- most.  
tricity consumption.  
Cooked foods, cold dishes, etc..: these should be covered  
and may be placed on any shelf.  
Fruit and vegetables: these should be thoroughly cleaned  
and placed in the special drawer(s) provided.  
Butter and cheese: these should be placed in special air-  
tightcontainersorwrappedinaluminium foil orpolythene  
bags to exclude as much air as possible.  
Milkbottles:theseshouldhaveacapandshouldbestored  
in the bottle rack on the door.  
Bananas, potatoes, onions and garlic, if not packed, must  
not be kept in the refrigerator.  
Hints for fresh food refrigeration  
To obtain the best performance:  
• do not store warm food or evaporating liquids in the  
refrigerator  
• do cover or wrap the food, particularly if it has a strong  
flavour  
• position food so that air can circulate freely around it  
Hints for refrigeration  
Useful hints:  
Meat (all types) : wrap in polythene bags and place on the  
glass shelf above the vegetable drawer.  
Care and Cleaning  
casing of this appliance is only cleaned with warm water  
with a little washing-up liquid added.  
After cleaning, reconnect the equipment to the mains  
supply.  
Caution! Unplug the appliance before carrying out  
any maintenance operation.  
This appliance contains hydrocarbons in its cooling  
unit; maintenance and recharging must therefore  
only be carried out by authorized technicians.  
Defrosting of the refrigerator  
Frost is automatically eliminated from the evaporator of  
the refrigerator compartment every time the motor com-  
pressor stops, during normal use. The defrost water  
drains out through a trough into a special container at the  
back of the appliance, over the motor compressor, where  
it evaporates.  
It is important to periodically clean the defrost water drain  
holeinthemiddleoftherefrigeratorcompartmentchannel  
to prevent the water overflowing and dripping onto the  
food inside. Use the special cleaner provided, which you  
will find already inserted into the drain hole.  
Periodic cleaning  
The equipment has to be cleaned regularly:  
• clean the inside and accessories with lukewarm water  
and some neutral soap.  
• regularly check the door seals and wipe cleantoensure  
they are clean and free from debris.  
• rinse and dry thoroughly.  
Important! Do not pull, move or damage any pipes and/  
or cables inside the cabinet.  
Never use detergents, abrasive powders, highly perfumed  
cleaning products or wax polishes to clean the interior as  
this will damage the surface and leave a strong odour.  
Clean the condenser (black grill) and the compressor at  
thebackoftheappliancewithabrushoravacuumcleaner.  
This operation will improve the performance of the ap-  
pliance and save electricity consumption.  
Important! Take care of not to damage thecooling system.  
Periods of non-operation  
When the appliance is not in use for long periods, take  
the following precautions:  
Many proprietary kitchen surface cleaners contain chem-  
icals that can attack/damage the plastics used in this ap-  
pliance. For this reason it is recommended that the outer  
disconnect the appliance from electricity supply  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
• remove all food  
If the cabinet will be kept on, ask somebody to check it  
once in a while to prevent the food inside from spoiling  
in case of a power failure.  
3)  
defrost and clean the appliance and all accessories  
• leave the door/doors ajar to prevent unpleasant smells.  
What to do if…  
Warning! Before troubleshooting, disconnect the  
mains plug from the mains socket.  
Only a qualified electrician or competent person must do  
the troubleshooting that is not in this manual.  
Important! There are some sounds during normal use  
(compressor, refrigerant circulation).  
Problem  
Possible cause  
Solution  
The appliance does not operate. The appliance is switched off.  
The lamp does not operate.  
Switch on the appliance.  
The mains plug is not connected to the Connect the mains plug to the mains  
mains socket correctly. socket correctly.  
The appliance has no power. There is Connect a different electrical appliance  
no voltage in the mains socket.  
to the mains socket.  
Contact a qualified electrician.  
The lamp does not work.  
The lamp is in stand-by.  
The lamp is defective.  
Close and open the door.  
Refer to "Replacing the lamp".  
The compressor operates con- The temperature is not set correctly. Set a higher temperature.  
tinually.  
The door is not closed correctly.  
Refer to "Closing the door".  
The door has been opened too fre-  
quently.  
Do not keep the door open longer than  
necessary.  
The product temperature is too high. Let the product temperature decrease to  
room temperature before storage.  
The room temperature is too high.  
Water flows on the rear plate of During the automatic defrosting proc- This is correct.  
the refrigerator. ess, frost defrosts on the rear plate.  
Water flows into the refrigerator. The water outlet is clogged.  
Products prevent that water flows into Make sure that products do not touch  
the water collector. the rear plate.  
Decrease the room temperature.  
Clean the water outlet.  
Water flows on the ground.  
The melting water outlet does not flow Attach the melting water outlet to the  
in the evaporative tray above the com- evaporative tray.  
pressor.  
The temperature in the appliance The temperature regulator is not set  
is too low. correctly.  
Set a higher temperature.  
The temperature in the appliance The temperature regulator is not set  
Set a lower temperature.  
is too high.  
correctly.  
3) If foreseen.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Possible cause  
Solution  
The door is not closed correctly.  
Refer to "Closing the door".  
The product temperature is too high. Let the product temperature decrease to  
room temperature before storage.  
Many products are stored at the same Store less products at the same time.  
time.  
There is no cold air circulation in the Make sure that there is cold air circula-  
appliance.  
tion in the appliance.  
power (the maximum power is shown on the lamp  
cover).  
4. Install the lamp cover.  
5. Tighten the screw to the lamp cover.  
6. Connect the plug to the mains socket.  
7. Open the door. Make sure that the light comes on.  
Replacing the lamp  
Caution! Disconnect the plug from the mains  
socket.  
1. Remove the screw  
from the lamp cov-  
er.  
Closing the door  
1. Clean the door gaskets.  
2. If necessary, adjust the door. Refer to "Installation".  
2. Remove the lamp  
cover (refer to the  
illustration).  
3. Replace the used  
lamp with a new  
3. If necessary, replace the defective door gaskets. Con-  
tact the Service Center.  
lamp of the same  
Technical data  
Dimension of the recess  
Height  
Width  
Depth  
1030 mm  
560 mm  
550 mm  
The technical information are situated in the rating plate  
on the internal left side of the appliance and in the energy  
label.  
Installation  
Caution! Read the "Safety Information" carefully for  
your safety and correct operation of the appliance  
before installing the appliance.  
Positioning  
Install this appliance at a location where the ambient tem-  
perature corresponds to the climate class indicated on the  
rating plate of the appliance:  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
The appliance must be earthed. The power supply cable  
plug is provided with a contact for this purpose. If the  
domestic power supply socket is not earthed, connect the  
appliance to a separate earth in compliance with current  
regulations, consulting a qualified electrician.  
The manufacturer declines all responsibility if the above  
safety precautions are not observed.  
Climate  
class  
Ambient temperature  
+10°C to + 32°C  
SN  
N
+16°C to + 32°C  
+16°C to + 38°C  
+16°C to + 43°C  
ST  
T
This appliance complies with the E.E.C. Directives.  
Electrical connection  
Before plugging in, ensure that the voltage and frequency  
shown on the rating plate correspond to your domestic  
power supply.  
Door reversibility  
The door of the appliance  
opens to the right. If you  
want to open the door to the  
left, do these steps before  
you install the appliance:  
On the opposite side:  
• Install the lower pin.  
• Install the door.  
• Tighten the spacer and  
tighten the upper pin.  
• Loosen the upper pin  
and remove the spacer.  
• Remove the door.  
• Loosen the lower pin.  
• Remove the upper pin  
and the door.  
Ventilation requirements  
The airflow behind the ap-  
Installing the appliance  
Caution! Make sure that the mains cable can move  
freely.  
min.  
50 mm  
200 cm2  
pliance must be sufficient.  
Do the following steps:  
min.  
200 cm2  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
I
2
1
4mm  
44mm  
I
Install the appliance in the Adjust the appliance in the Attach the appliance to the Push the sealing strip be-  
niche.  
niche.  
niche with 4 screws.  
tween the appliance and the  
adjacent cabinet.  
Push the appliance in the The lower hinge cover (in  
direction of the arrows (1) the accessories bag)makes  
until the upper gap cover sure that the distance be-  
stops against the kitchen tween the appliance and the  
furniture. Make sure that  
the distance between the  
appliance and the cup-  
kitchen furniture is correct.  
Open the door. Put the low-  
er hinge cover in position.  
board front-edge is 44 mm.  
Push the appliance in the  
direction of the arrows (2)  
againstthecupboardonthe  
opposite side of the hinge.  
Make sure that the clear-  
ance between the appliance  
and the cupboard is 4 mm.  
ca. 50 mm  
90°  
Ha  
Hb  
C
D
21 mm  
90°  
E
Hc  
Hd  
E
ca. 50 mm  
21 mm  
Remove the correct part  
from the hinge cover (E). the lugs and the hinge  
Make sure to remove the holes.  
Attach the covers (C, D) to Disconnect the parts (Ha),  
(Hb), (Hc) and (Hd).  
Install the part (Ha) on the  
inner side of the kitchen  
furniture.  
part DX, in the case of right Attach the hinge covers (E)  
hinge, SX in opposite case. to the hinge.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 mm  
8 mm  
Hb  
Ha  
K
Ha  
Hc  
Ha  
Hb  
Push the part (Hc) on the Open the appliance door  
Remove the brackets and Place the small square on  
mark a distance of 8 mm the guide again and fix it  
from the outer edge of the with the screws supplied.  
part (Ha).  
and the kitchen furniture  
door at an angle of 90°.  
Insert the small square(Hb) door where the nail must be Align the kitchen furniture  
into guide (Ha).  
fitted (K).  
door and the appliance  
door by adjusting the part  
Hb.  
Put together the appliance  
door and the furniture door  
and mark the holes.  
Hb  
Hd  
Press the part (Hd) on the  
part (Hb).  
Do a final check to make sure that:  
• All screws are tightened.  
• The magnetic sealing strip is attached tightly to the  
cabinet.  
Important! If the ambient temperature is low (for example,  
in the Winter), the size of the gasket decreases. The size  
of the gasket increases when the ambient temperature  
increases.  
Environmental concerns  
negative consequences for the environment and human  
health, which could otherwise be caused by inappropriate  
waste handling of this product. For more detailed  
information about recycling of this product, please  
contactyourlocalcouncil,yourhouseholdwastedisposal  
service or the shop where you purchased the product.  
The symbol  
on the product or on its packaging  
indicates that this product may not be treated as  
household waste. Instead it should be taken to the  
appropriate collection point for the recycling of electrical  
and electronic equipment. By ensuring this product is  
disposed of correctly, you will help prevent potential  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weed Eater Trimmer 530087729 User Manual
Whirlpool Clothes Dryer 7MWGD9200 User Manual
Whirlpool Dishwasher DU018DWTB User Manual
Whirlpool Range 9762035A User Manual
Whirlpool Ventilation Hood RHH2600 User Manual
Williams Sound Stereo System PPA R35 8N User Manual
Windsor Vacuum Cleaner SRS12 User Manual
Wolf Oven RB36 User Manual
Woodstock Nail Gun W1777 User Manual
Xtant Speaker A212 User Manual