Instruction
booklet
Gas hob
ZGF 642
ZGF 692 C
ZGF 692 CT
GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Information .........................................................4
Description of the Hobs.........................................................................6
Instructions for the User.................................................................7
Operation ..............................................................................................8
Maintenance and Cleaning .................................................................10
Something Not Working? ....................................................................12
Guarantee/Customer Service .............................................................28
European Guarantee ..........................................................................30
Instructions for the Installer ........................................................ 13
Engineer technical data.......................................................................13
Important safety requirements............................................................15
Installation............................................................................................16
Gas Connection...................................................................................17
Location...............................................................................................18
Fitting the Hob into the Worktop......................................................... 19
Building In............................................................................................20
Building over a cupboard or drawer ..................................................20
Building over a kitchen unit with door .................................................20
Electrical Connections.........................................................................21
Wiring diagram ...................................................................................22
Fault Finding ........................................................................................23
Commissioning....................................................................................26
Conversion from Natural Gas to LPG .................................................27
Guide to Use the instructions
The following symbols will be found in the text to guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
!
Hints and Tips
Environmental information
"
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.P.A.
Viale Bologna, 298 - 47100 Forlì - Italy
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
You MUST read these warnings carefully before installing or
using the hob. If you need assistance, contact our Customer
Care Department on 08705 727 727.
Installation
#
This appliance must be installed and serviced by a competent person as
stated in the Gas Safety (Installation and Use) Regulations Current Editions
and the IEE Wiring Regulations.
#
For appliances installed in the Republic of Ireland please refer to NSAI-
Domestic Gas Installations I.S.813 Current Editions and the ETCI Rules for
Electrical Installations.
#
#
Remove all packaging before using the hob.
Ensure that the gas and electrical supply complies with the type stated on
the rating plate, located near the gas supply pipe.
#
Do not attempt to modify the hob in any way.
Child Safety
#
This hob is designed to be operated by adults. Do not allow children to play
near or with the hob.
#
This appliance is not intended for use by children or other persons whose
physical, sensory or mental capabilities or lack of experience and knowledge
prevents them from using the appliance safely without supervision or instruction
by a responsible person to ensure that they can use the appliance safely.
#
#
The hob gets hot when it is in use. Children should be kept away until it has
cooled.
Children can also injure themselves by pulling pans or pots off the hob.
During Use
#
This hob is intended for domestic cooking only. It is not designed for
commercial or industrial purposes.
#
This appliance is not connected to a combustion products evacuation device.
It must be installed and connected in accordance with current installation
regulations. Particular attention shall be given to the relevant requirements
regarding ventilation.
#
#
When in use a gas cooking hob will produce heat and moisture in the room
in which it has been installed. Ensure there is a continuous air supply, keeping
air vents in good condition or installing a cooker hood with a venting hose.
Ensure a good ventilation around the appliance. A poor air supply could cause
lack of oxygen.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
#
#
When using the hob for a long period time, the ventilation should be
improved, by opening a window or increasing the extractor speed.
Do not use this hob if it is in contact with water. Do not operate the hob with
wet hands.
#
#
Ensure the control knobs are in the ‘OFF’ position when not in use.
When using other electrical appliances, ensure the cable does not come
into contact with the hot surfaces of the cooking appliance.
#
Unstable or misshapen pans should not be used on the hob as unstable
pans can cause an accident by tipping or spillage.
#
#
#
Never leave the hob unattended when cooking with oil and fats.
Never use plastic or aluminium foil dishes on the hob.
Perishable food, plastic items and areosols may be affected by heat and
should not be stored above or below the hob unit.
#
This appliance cannot be cleaned with steam or with a steam cleaning
machine.
Service
#
This hob should only be repaired or serviced by an authorised Service
Engineer and only genuine approved spare parts should be used.
Environmental Information
After installation, please dispose of the packaging with due regard to
safety and the environment.
"
#
#
When disposing of an old appliance, make it unusable, by cutting off the
cable.
#
The symbol
on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the
product.
These instructions are only valid for countries whose identification symbols
are shown on the cover of this instruction booklet and on the appliance itself.
Keep this instruction book for future reference and ensure it is
passed on to any new owner.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the Hobs
Model ZGF 642
3
2
3
1
4
6
Model ZGF 692 C-
ZGF 692 CT
3
2
3
1
5
6
1. Hob Top
2. Auxiliary Burner
3. Semi-rapid Burner
4. Rapid Burner
5. Triple crown Burner
6. Control knobs
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for the User
INSTALLATION
Any gas installation must be carried out by a registered
competent person, and in accordance with existing rules and
regulations.
The relevant instructions are to be found in the second section of this
manual.
Please, ensure that, once the hob is installed, it is easily accessible for
the engineer in the event of a breakdown.
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important to remove any protective
materials, which were put on in the factory.
The manufacturer will not accept liability, should the above instructions or
any of the other safety instructions incorporated in this book be ignored.
Operation
Lighting the burners
For easier lighting, proceed before putting
a pan on the pan support.
To light a burner:
turn the relevant knob anti-clockwise to maximum
!
#
position (
burner.
), then push it down to ignite the
Triple crown burner
(mod. ZGF 692 C/CT)
Only for model ZGF 692 CT
#
Upon ignition, keep the knob pushed down
about 5 seconds. This will allow the
"thermocouple" (Fig. 1 - letter D) to be heated
and the safety device to be switched off,
otherwise the gas supply would be interrupted.
A
B
#
Then adjust the flame as required.
D
C
If the burner does not ignite, turn the control knob
to zero, and try again.
A - Burner cap
B - Burner crown
If you cannot light the flame even after
severalattempts, check the "cap" (Fig. - lett. A)
and the"crown" (Fig. - lett. B) are in the correct
position.
C - Ignition electrode
D - Thermocouple (only in
model ZGF 692 CT)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
When switching on the mains, after installation or a power cut, it is quite
normal for the spark generator to be activated automatically.
In the absence of electricity, ignition can occur without the electrical
device; in this case, approach the burner with a flame, push the relevant
knob down and turn it anti-clockwise until it reaches the maximum position.
If the control knobs become difficult to turn, please contact your local
Service Force Centre.
Using the Wok Stand (only for
model ZGF 692 C, ZGF 692 CT)
A wok stand is provided to enable you to use a
round bottomed wok on the hob. The wok stand
must only be used on the triple crown burner,
and should not be used with any other type of
wok or pan. When fitting the wok stand, ensure
the recesses in the frame fit securely onto the bars
of the pan supports, as shown in the picture.
Using the hob correctly
To ensure maximum burner efficiency, it is strongly recommended that you
use only pots and pans with a flat bottom fitting the size of the burner used,
so that flame will not spread beyond the bottom of the vessel (see the table
below).
Burner
minimum
diameter
maximum
diameter
Triple crown
Large (rapid)
Medium (semi-rapid) 120 mm
Small (auxiliary) 80 mm
180 mm
180 mm
260 mm
260 mm
220 mm
160 mm
8
Download from Www.Somanuals.com. All Manuals Search And Download.
As soon as a liquid starts boiling, turn down
the flame so that it will barely keep the
liquid simmering.
Use only pans or pots with flat
bottom.
If you use a saucepan which is smaller
than the recommended size, the
flame will spread beyond the bottom
of the vessel, causing the handle to
overheat.
Carefully supervise cooking with fat or oil,
since these types of foodstuff can result in
a fire, if over-heated.
The stainless steel can become tarnished if excessively
heated. Therefore prolonged cooking with potstones,
earthenware pans or cast-iron plates is inadvisable. Also,
do not use aluminium foil to protect the top during use.
Make sure pots do not protrude over the edges of the cooktop
and that they are centrally positioned on the rings in order to
obtain lower gas consumption.
Do not place unstable or deformed pots on the rings: they
could tip over or spill their contents, causing accidents.
Pots must not enter the control zone.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Before any maintenance or cleaning can be carried out, you
must DISCONNECT the hob from the electricity supply.
The hob is best cleaned whilst it is still warm, as spillage can
be removed more easily than if it is left to cool.
This appliance cannot be cleaned with steam or with a steam
cleaning machine.
The Hob Top
Regularly wipe over the hob top using a soft cloth well wrung out in warm water to
which a little wasing up liquid has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, the following products are
recommended:
- For stainless steel hobs use a proprietary
stainless steel cleaner.
- For other hobs use Hob Brite or Bar Keepers
Friend.
Do not leave acid or alkaline
substances (e.g. vinegar, salt,
lemon juice, etc.) on the cooktop.
Pan Supports
To keep the pan supports in the correct
Fig. 1
position, they are hooked into hinges at the
back of the hob.
Model ZGF 642: The pan supports can
be lifted for easier cleaning, as shown in Fig.
1.
YES
To remove the pan supports completely,
proceed as shown in Fig. 2.
Model ZGF 692 C, ZGF 692 CT: The
hob has two cast iron pan supports.
Fig. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Take care when removing them.
They are heavy and could
damage the hob or your kitchen
furniture if you let them fall.
NO
Never turn the cast iron pan supports
on the hinges, this could damage
them.
To remove the cast iron pan supports
completely, proceed as shown in Fig.
2.
Wash the pan supports using hot soapy
water. If necessary, a paste cleaner or a
soap impregnated steel wool pad can be
used with caution.
Fig. 3
After cleaning, be sure to wipe dry with a soft cloth and make sure that the
pan supports are correctly positioned.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burners caps and crowns using hot soapy water, and remove
marks with a mild paste cleaner. A well moistened soap impregnated steel
wool pad can be used with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
The Ignition electrode
The electric ignition is obtained through a ceramic electrode which contains
a metal electrode. Keep these components very clean, to avoid difficult
lighting, and check that the burner crown holes are not obstructed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working?
If the hob is not working correctly, please carry out the following checks
before contacting your local Service Force Centre.
SYMPTOM
SOLUTION
$
There is no spark when
lighting the gas.
%
Check that the unit is plugged
in and the electrical supply is
switched on.
%
%
%
Check that the RCCB has not
tripped (if fitted).
Check the mains fuse has not
blown.
Check the burner cap and
crown have been replaced
correctly, e.g. after cleaning.
$
The gas ring burns unevenly.
%
%
Check the main jet is not
blocked and the burner crown
is clear of food particles.
Check the burner cap and
crown have been replaced
correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate correctly, contact
your local Service Force Centre.
Please note that it will be necessary to provide proof of purchase for any in-
guarantee service calls.
In-guarantee customers should ensure that the above checks have been
made as the engineer will make a charge if the fault is not a mechanical or
electrical breakdown.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for the Installer
Engineer technical data
OVERALL DIMENSIONS
Width:
Depth:
580 mm
510 mm
CUT OUT DIMENSIONS
Width:
Depth:
560 mm
480 mm
Thickness: 30 mm
SUPPLY CONNECTIONS
Gas:
R 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
230 V~ 50 Hz supply, 3 core flexible cable with
non rewireable plug fitted with a 3 amp cartridge fuse
HEAT INPUT
Rear Left Burner
(semi-rapid)
2.0 kW (6826 BTU/HR)
Front Right Burner
(Mod. ZGF 642)
(rapid)
3.0 kW Natural Gas (10239 BTU/HR)
2.8 kW L.P.G. (9556 BTU/HR)
Front Right Burner
(Mod. ZGF 692 C, ZGF 692 CT)
(triple crown)
4.0 kW Natural Gas (13652 BTU/HR)
Rear Right Burner
(semi-rapid)
2.0 kW (6826 BTU/HR)
Front Left Burner
(auxiliary)
1.0 kW (3413 BTU/HR)
APPLIANCE CLASS
APPLIANCE CATEGORY
GAS SUPPLY
3
II2H3+
Natural gas G20 (2H) / 20 mbar
This appliance is manufactured according to the following EEC
directives:
2006/95 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current
edition.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BURNER
POSITION
RAPID
SEMI-RAPID A U X I L I A R Y TRIPLECROWN
TYPE OF GAS
MAX MIN MAX MIN MAX MIN
MAX
MIN
NOMINALTHERMAL
POWER
kW
3.0
0.65
2.0
0.45
1.0
0.33
4.0
1.2
NATURAL GAS
20 mbar
NOMINALFLOW
RATE
m3/h 0.286 0.057 0.190 0.038 0.095 0.028
119 Adjust. 96 Adjust. 70 Adjust.
0.381
146
0.114
VALUE =
37.78 MJ/m3
Ws - 50.7 MJ/ m3
NOZZLEREFERENCE
1/100mm
Adjust.
NOMINALTHERMAL
POWER
kW
2.8
0.65
2.0
0.45
1.0
0.33
4.0
1.2
LPG GAS
28-30/37 mbar
VALUE =
NOMINALFLOW
RATE
g/h
202 43.5
86 40
144
71
29
32
72
50
21,5
28
291
98
87
56
49.92 MJ/Kg
NOZZLEREFERENCE
1/100mm
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety requirements
This hob must be installed in accordance with the Gas Safety (Installation and Use)
Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).
For appliances installed in the Republic of Ireland please refer to NSAI- Domestic
Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
Provision for Ventilation
Detailed recommendations are contained in the following British Standards Codes Of
Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.
The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
If it is installed in a room of volume less than 5 m3 an air vent of effective area of 100
cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent
of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is
required.
However, if the room has a door which opens directly to the outside no air vent is
required even if the volume is between 5 m3 and 11 m3.
If there are other fuel burning appliances in the same room, B.S. 5440 Part 2 Current
Edition, should be consulted to determine the requisite air vent requirements.
For appliances installed in the Republic of Ireland please refer to the NSAI- Domestic
Gas Installation I.S. 813 Current Editions Table Four.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
IMPORTANT
This hob must be installed by a competent person to the
relevant Gas Standards.
Any gas installation must be carried out by a registered
competent person.
Please, ensure that, once the hob is installed, it is easily accessible for the
engineer in the event of a breakdown.
The manufacturer will not accept liability, should the above instructions or
any of the other safety instructions incorporated in this instruction booklet
be ignored.
On the end of the shaft, which includes the G 1/2" threaded elbow,
adjustment is fixed so that the washer is fitted between the components
as shown in the diagram. Screw the parts together without using excessive
force.
A) End of shaft with nut
B) Washer
C) Elbow
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Connection
Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel
or copper.
The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread).
When the final connection has been made, it is essential that a thorough leak test is
carried out on the hob and installation.
Ensure that the main connection pipe does not exert any strain on the hob.
It is important to install the elbow corr
e
c
t
l
y,
w
i
t
h
t
h
e
s
h
o
u
l
d
e
r
o
n
the end of the thread, fitted to the hob connecting pipe.
Failure to ensure the correct assembly will cause leakage of gas.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Location
The hob may be located in a kitchen, a
kitchen/diner or bed sitting room, but not
in a bathroom, shower room or garage.
Ensure that there is a minimum distance
of 55 mm between the rear cut out edge
and the wall.
6
0
0
M
IN
.
A minimum distance of 100 mm must be
left between the side edges of the cut out
and any adjacent cabinets or walls.
The minimum distance combustible
material can be fitted above the hob in
line with the edges of the hob is 400 mm.
If it is fitted below 400 mm a space of 50
mm must be allowed from the edges of
the hob.
The minimum distance combustible
material or a cooker hooh can be fitted
above the hob is 650 mm.
For appliances installed in the Republic
of Ireland please refer to NSAI- Domestic
Gas Installation I.S 813 Current Edition
Section 7- Permitted Locations of
Appliance.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting the Hob into the
Worktop
Carry out the building in of the hob as
follows:
1. place the seals supplied with
the hob on the side edges of the
cut out and at 8 mm. from the
front and rear edges, as shown
in the diagram, taking care that
the seals meet without
overlapping;
2. place the hob in the cut out,
taking care that it is centred;
3. fix the hob with the relevant
fixing clamps and screws, as
shown in the diagram. When the
screws have been tightened,
the excess seal can be
removed.
Seal
The edge of the hob forms a double seal
which prevents the ingress of liquids.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Building In
Building over a cupboard or drawer
If the hob is to be installed above a cupboard or drawer it will be necessary to fit a
heat resistant board below the base of the hob on the underside of the work surface.
It is also recommended to carry out the electrical connection to the hob as shown
in diagrams 1 and 2.
1
Building over a kitchen unit
with door
Proper arrangements must be taken in designing
the furniture unit, in order to avoid any contact
with the bottom of the hob which can be heated
when it is operated. The recommended solution
is shown in diagram 3.
The panel fitted under the hob ("a") should be
easily removable to allow easy access if
technical assistance is needed. The space
behind the kitchen unit ("b") can be used for
connections.
Dimensions are given in mm.
2
3
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Any electrical work required to install this hob should be
carried out by a qualified electrician or competent person,
in accordance with the current regulations.
THIS HOB MUST BE EARTHED.
Electrical Requirements
Any permanent electrical installation must comply with the latest I.E.E.
Regulations and local Electricity Board regulations. For your own safety
this should be undertaken by a qualified electrician, e.g. your local Electricity
Board, or a contractor who is on the roll of the National Inspection Council
for Electrical Installation Contracting (NICEIC).
The manufacturer declines any liability should these safety
measures not be observed.
This hob is designed to be connected to a 230 V 50 Hz AC electrical supply.
Before switching on, make sure the electricity supply voltage is the same
as that indicated on the hob rating plate. The rating plate is located on the
bottom of the hob. A copy is attached on
the back cover of this book.
The hob is supplied with a 3 core flexible
supply cord incorporating a 3 amp plug
fitted. In the event of having to change the
fuse, a 3 amp ASTA approved (BS 1362)
fuse must be used.
Should the plug need to be replaced for
any reason, the wires in the mains lead are
coloured in accordance with the following
code:
FO 0390
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
1) Connect the green and yellow (earth) wire to the terminal in the
plug which is marked with the letter 'E' or the earth symbol
or coloured green and yellow.
!
2) Connect the blue (neutral) wire to the terminal in the plug which
is marked with the letter 'N' or coloured black.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Connect the brown (live) wire to the terminal in the plug which
is marked with the letter 'L' or coloured red.
Upon completion there must be no cut, or stray strands of wire present
and the cord clamp must be secure over the outer sheath.
A cut off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut off plug is disposed
of safely.
The replacement of electric cable must be carried out ex-
clusively by the service force centre or by personnel with
similar competencies, in accordance with the current regu-
lations.
Permanent Connection
In the case of a permanent connection, it is necessary that you install a
double pole switch between the hob and the electricity supply (mains),
with a minimum gap of 3 mm between the switch contacts and of a type
suitable for the required load in compliance with the current electric
regulations.
The switch must not break the yellow and green earth cable at any point.
Ensure that the hob supply cord does not come into contact
with surfaces with temperatures higher than 50 deg. C.
Wiring diagram
1
2
1. TAPS IGNITOR SWITCHES
2. IGNITOR UNIT
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Finding
Preliminary Electrical Systems Check
Blue
Brown
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
Blue
Green
Yellow
Brown
YES
NO
Carry out:
C: Polarity check.
Carry out:
D: Resistance to
Earth check.
Has inlet fuse blown?
NO
Electricity supply
should now be
satisfactory.
YES
PLUG (with cover removed)
Earth Wire
SOCKET
(face view)
Inlet wiring
faulty.
Rectify any
fault.
Green/Yellow
( )
( )
E
Neutral Wire
Blue
N
L
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
A. EARTH CONTINUITY CHECK
Appliance must be electrically disconnected - meter set on W (Ohms)
x 1 scale and adjust zero if necessary.
— Test leads from any appliance earth point to earth pin on plug.
Resistance should be less than 0.1 W (Ohm), check all earth wires
for continuity and all contacts clean and tight.
B. INSULATION CHECK
Appliance electrically disconnected, all switches ON.
a) meter set on W (Ohms) x 1 scale.
Test leads from L to N in appliance terminal block. If meter reads
«0» then there is a short circuit.
b) meter set on W (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads less than ×
(infinity) there is a fault.
NOTE - Should it be found that the fuse has failed but no fault is indicated
- a detailed continuity check (i.e. by disconnecting and checking each
component) is required to trace the faulty component.
It is possible that a fault could occur as a result of local burning/arcing but
no fault could be found under test. However a detailed visual inspection
should reveal evidence of burning around the fault.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Ignition System / Gas Ignition
YES
Check gas supply at
burner
Ignitor does not spark
NO
Check plug top fuse and
replace if necessary
Light burner manually
Check polarity and
earth continuity of
supply point
Check by pass simmer
adjusted
Check fitting
of burners
Check position of the
electrode
Check earth continuity
of appliance
Check continuity from the tip of
each electrode to the terminals
1 to 4 on the ignitor unit
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check for breaks in the
insulation of the HT leads
Check continuity from ignition
switches connector to ignitor unit
Change the ignitor unit
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Commissioning
When the hob has been fully installed it will be necessary to check the
minimum flame setting. To do this, follow the procedure below.
1) Turn the gas tap to the MAX position and ignite.
!
2) Set the gas tap to the MIN flame position then turn the control
knob from MIN to MAX several times. If the flame is unstable or is
extinguished follow the procedure below.
Procedure:
1) Re-ignite the burner and set
!
to MIN.
2) Remove the control knob.
3) To adjust, use a thin bladed
screwdriver and turn the
adjustment screw (see
diagram) until the flame is
steady and does not
Minimum adjustment
extinguish, when the knob is
screw
turned from MIN to MAX.
Repeat this procedure for all
burners.
Pressure Testing
The pressure testing must be carried out on the burners.
Proceed as follows:
!
1) Remove the pan supports and the burner caps and crowns.
2) Fit manometer tube over the injector.
3) Turn on the burner gas supply and ignite another burner supply.
The pressure reading should be nominally 20 mbar and must be
between 17 mbar and 25 mbar.
4) Turn off the burner supplies.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion from Natural Gas to LPG
IMPORTANT
The replacement/conversion from natural gas to LPG should only
be undertaken by a competent person.
It is important to note that this model is designed for use with natural gas but can be
converted for use with butane or propane gas providing the correct injectors are
fitted. The gas rate is adjusted to suit.
Method
1) Ensure that the gas taps are in the 'OFF' position
!
2) Isolate the hob from the electricity supply
3) Remove all pan supports, burner caps, rings, crowns and control knobs.
4) With the aid of a 7mm box spanner the burner injectors can then be
unscrewed and replaced by the appropriate LPG injectors.
TO ADJUST THE GAS RATE
With the aid of a thin bladed screwdriver completely tighten down the by
pass adjustment screw. Upon completion stick the replacement rating plate
on the under side of the hob.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee/Customer Service
Standard guarantee conditions
We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase
this Zanussi-Electrolux appliance or any part thereof is proved to be defective by
reason only of faulty workmanship or materials, we will, at our option repair or replace
the same FREE OF CHARGE for labour, materials or carriage on condition that:
· The appliance has been correctly installed and used only on the electricity supply
stated on the rating plate.
· The appliance has been used for normal domestic purposes only, and in accord-
ance with the manufacturer’s instructions.
· The appliance has not been serviced, maintained, repaired, taken apart or tam-
pered with by any person not authorised by us.
· Electrolux Service Force Centre must undertake all service work under this guaran-
tee.
· Any appliance or defective part replaced shall become the Company’s property.
· This guarantee is in addition to your statutory and other legal rights.
Exclusions
· Damage or calls resulting from transportation, improper use or neglect, the re-
placement of any light bulbs or removable parts of glass or plastic.
· Costs incurred for calls to put right an appliance which is improperly installed or
calls to appliances outside the United Kingdom.
· Appliances found to be in use within a commercial environment, plus those which
are subject to rental agreements.
· Products of Electrolux manufacturer that are not marketed by Electrolux.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare
parts, please contact your local Service Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre covering
your postcode area.
For the address of your local Service Force Centre and further information about Service
Force, please visit the website at
Before calling out an engineer, please ensure you have read the details under the
heading “Something not working”
When you contact the Service Force Centre you will need to give the following details:
1.Your name, address and postcode.
2.Your telephone number.
3. Clear concise details of the fault.
4. The model and Serial number of the appliance (found on the rating plate).
5.The purchase date.
Please note a valid purchase receipt or guarantee documentation is required for in
guarantee service calls.
Customer Care
For general enquiries concerning your Electrolux appliance, or for further information
on Electrolux products please contact our Customer Care Department by letter or
Customer Care Department
Electrolux Major Appliances
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 727 727 (*)
(*) Calls may be recorded for training purposes
29
Download from Www.Somanuals.com. All Manuals Search And Download.
European Guarantee
This appliance is guaranteed by Electrolux in each of the countries listed
at the back of this user manual, for the period specified in the appliance
guarantee or otherwise by law. If you move from one of these countries to
another of the countries listed below the appliance guarantee will move
with you subject to the following qualifications:
• The appliance guarantee starts from the date you first purchased the
appliance which will be evidenced by production of a valid purchase
document issued by the seller of the appliance.
• The appliance guarantee is for the same period and to the same extent
for labour and parts as exists in your new country of residence for this
particular model or range of appliances.
• The appliance guarantee is personal to the original purchaser of the
appliance and cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions
issued by Electrolux and is only used within the home, i.e. is not used
for commercial purposes.
• The appliance is installed in accordance with all relevant regulations in
force within your new country of residence.
The provisions of this European Guarantee do not affect any of the rights
granted to you by law.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
35670-9509
04/07 R.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|