Model No. WESY39523
Serial No.
USER'S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if parts are
missing, we will guarantee com-
plete satisfaction through assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our cus-
tomer hot line will provide imme-
diate assistance, free of charge.
CUSTOMER HOT LINE:
Patent Pending
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight system.
1. Read all instructions in this manual and in
the accompanying literature before using the
weight system.
13. Always disconnect the lat bar from the
weight system when performing an exercise
that does not use the lat bar.
2. It is the responsibility of the owner to ensure
that all users of the weight system are ade-
quately informed of all precautions.
14. Make sure that the cables remain on the pul-
leys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
3. The weight system is intended for home use
only. Do not use the weight system in any
commercial, rental, or institutional setting.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
4. Use the weight system only on a level sur-
face. Cover the floor beneath the weight sys-
tem to protect the floor.
16. The decals shown below have been placed
on the weight system in the locations shown
on page 4. If a decal is missing or illegible,
call our toll-free Customer Hot Line at
5. Make sure that all parts are properly tight-
ened each time the weight system is used.
Replace any worn parts immediately.
1-800-999-3756 and order a free replacement
decal. Apply the decal in the location shown.
6. Keep children under 12 and pets away from
the weight system at all times.
Keep hands and
fingers clear of
this area.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protection.
Decal 2
9. The weight system is designed to support a
a maximum user weight of 300 pounds.
10. The weight system should not be used by
more than one person at a time.
11. Always stand on the foot plate when per-
forming an exercise that could cause the
weight system to tip.
Decal 1
12. Never release the butterfly arms, leg lever,
squat arm, lat bar, row bar, or handle while
weights are raised; the weights will fall with
great force.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
3650 weight system. The WEIDER® PRO 3650 weight
system offers an impressive array of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength, or improve your
cardiovascular system, the PRO 3650 weight system
will help you to achieve the specific results you want.
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WESY39523. The
serial number can be found on a decal attached to the
weight system (see the front cover of this manual for
the location of the decal).
For your benefit, read this manual carefully before
using the weight system. If you have additional
questions, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
WARNING
DECAL 1
ASSEMBLED
DIMENSIONS:
Height: 81 in.
Width: 96 in.
Length: 57 in.
Lat Bar
High Pulley Station
Swivel Carriage
WARNING DECAL 2
(one on each side)
Butterfly Arm/Press Arm
Adjustment Handle
Squat Arm
Backrest
Backrest
Low Pulley Station
Adjustment Knob
Seat
Adjustment Handle
WARNING
DECAL 2
Leg Lever
Squat Knee Rest
Weight Stack
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Make sure that you have the following tools:
• Two adjustable wrenches
• One standard screwdriver
• One phillips screwdriver
Make Assembly Easier
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by anyone.
Before beginning assembly, make sure to
read the information on this page. This
brief introduction will save you much more
time than it takes to read it.
• One rubber mallet
• You will also need grease or petroleum jelly, a
small amount of soapy water, and masking tape.
Note: Assembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Assembly Requires Two Persons
For your convenience and safety, assemble the
weight system with the help of another person.
How to Identify Parts
Set Aside Enough Time
To help you identify the small parts used in assembly,
a PART IDENTIFICATION CHART is included in the
center of this manual. Lay the chart on the floor and
use it to easily identify parts during each assembly
step. Note: Some small parts may have been pre-
attached. If a part is not in the parts bag, check
to see if it has been pre-attached.
Due to the many features of the weight system, the
assembly process will require several hours. By
setting aside plenty of time and by deciding to
make the task enjoyable, assembly will go smoothly.
Select a Location for the Weight System
Because of its weight and size, the weight system
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.
How to Orient Parts
As you assemble the weight system, make sure that
all parts are oriented exactly as shown in the draw-
ings.
How to Unpack the Box
Tightening Parts
To make assembly easier, we have divided the
assembly process into four stages. The small hard-
ware needed for each stage is packaged in sepa-
rate bags. Important: Wait until you begin each
stage to open the parts bag(s) for that stage.
Place all parts of the weight system in a cleared
area and remove the packing materials. Do not dis-
pose of the packing materials until assembly is com-
pleted.
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Questions?
If you have questions after reading the assembly
instructions, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time.
The Four Stages of the Assembly Process
Frame Assembly—You will begin by assembling
the base and the uprights that form the skeleton of
the weight system.
Cable Assembly—During this stage, you will
attach the cables and pulleys that connect the
weight stations to the weight stacks.
Arm Assembly—During this stage, you will
Seat Assembly—During the final stage, you will
assemble the arms and the leg lever.
assemble the seat and the backrests.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
FRAME ASSEMBLY
2
24
1.
Make sure that you understand all of the
information on page 5 before you begin
assembling the weight system.
120
14
Locate and open the parts bags labeled “FRAME
ASSEMBLY 1” and “FRAME ASSEMBLY 2.”
71
85
101
See the inset drawing. Attach the Base Cap (24)
to the Short Base (2) with two M4 x 20mm Self-tap-
ping Screws (14) and two M4 Washers (120).
110
2
87
Press a 50mm Square Inner Cap (105) into the
open end of the Long Base (101).
87
110
Insert eight M10 x 65mm Carriage Bolts (110) up
through the Long Base (101) and the Short Base
(2) as shown. Note: It may be helpful to place
tape over the heads of the Carriage Bolts to
hold them in place.
110
110
105
Attach the Short Base (2) to the Long Base (101)
with two M10 x 70mm Bolts (85), the Long Frame
Plate (71), and two M10 Nylon Locknuts (87).
2. Press two 50mm x 75mm Inner Caps (58) into the
Foot Plate (53). Attach the Foot Plate to the Long
Base (101) with two M10 x 65mm Carriage Bolts
(110) and two M10 Nylon Locknuts (87).
2
110
53
58
87
101
58
87
3. Attach the tether on the Long Pin w/Tether (112) to
the Long Base (101) with an M4 x 20mm Self-tap-
ping Screw (14).
3
Attach the four Knee Rest Bumpers (108) to the
Squat Knee Rest (41) with four M4 x 20mm Self-
tapping Screws (14). Attach the Squat Knee Rest to
the Long Base (101) with an M10 x 85mm Bolt (96)
and an M10 Nylon Locknut (87). Do not overtight-
en the Locknut; the Squat Knee Rest must be
able to pivot.
112
14
41
96
108
14
101
87
108
108
14
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press a 38mm Square Inner Cap (67) into the
Upright Extension (12).
4
Attach the Upright Extension (12) to the Butterfly
Upright (3) with two M10 x 95mm Bolts (92), two
M10 Washers (91), and two M10 Nylon Locknuts
(87). Make sure the warning decals on each side
of the Extension are right-side up.
92
12
87
91
67
92
Warning
Decal
Slide the Butterfly Upright (3) onto the two indicated
M10 x 65mm Carriage Bolts (110) in the Short Base
(2). Finger tighten an M10 Nylon Locknut (87) onto
each Carriage Bolt. Do not tighten the Locknuts
yet.
3
65
Tighten an Adjustment Handle (65) into the Butterfly
Upright (3).
87
87
2
110
5. Press a 50mm x 75mm Inner Cap (58) into the top
of the Seat Upright (9). Attach the Leg Lever
Bumper (77) to the Seat Upright with an M4 x
20mm Self-tapping Screw (14) and an M4 Washer
(120).
5
58
9
77
Slide the Seat Upright (9) onto the two indicated
M10 x 65mm Carriage Bolts (110) in the Short Base
(2). Finger tighten an M10 Nylon Locknut (87) onto
each Carriage Bolt. Do not tighten the Locknuts
yet.
14
87
2
120
87
110
6. Hold the Seat Frame (8) between the Seat Upright
(9) and the Butterfly Upright (3). Attach the Seat
Frame to the Seat Upright with two M10 x 95mm
Bolts (92), two M10 Washers (91), and two M10
Nylon Locknuts (87). Do not tighten the Locknuts
yet.
6
87
8
91
92
87
65
3
Attach the Seat Frame (8) to the Butterfly Upright
(3) with two M10 x 95mm Bolts (92), two M10
Washers (91), and two M10 Nylon Locknuts (87).
Do not tighten the Locknuts yet.
91
91
9
Tighten an Adjustment Handle (65) into the Seat
Frame (8).
92
91
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press a 50mm x 75mm Inner Cap (58) into the top
of the Squat Upright (4). Press two 25mm Round
Outer Cap (121) onto the Upright. Slide the Squat
Upright onto the two indicated M10 x 65mm
7
58
Carriage Bolts (110) in the Long Base (101). Finger
tighten an M10 Nylon Locknut (87) onto each
Carriage Bolt. Do not tighten the Locknuts yet.
58
5
Press a 50mm x 75mm Inner Cap (58) into the top
of the Swivel Upright (5). Slide the Swivel Upright
onto the two indicated M10 x 65mm Carriage Bolts
(110) in the Long Base (101). Finger tighten an M10
Nylon Locknut (87) onto each Carriage Bolt. Do not
tighten the Locknuts yet.
4
87
121
87
121
110
101
110
8. Press two Swivel Bushings (66) into the Swivel
Carriage (46).
8
66
Tighten an Adjustment Handle (65) into the Swivel
Carriage (46). Orient the Swivel Carriage as shown.
Slide the Carriage onto the Swivel Upright (5) and
engage the Adjustment Handle into an adjustment
hole in the Swivel Upright.
65
46
66
5
Adjustment
Hole
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Attach a Roller (39) between the indicated set of
holes in the Squat Slider (38) with an M8 x 85mm
Bolt (94) and an M8 Nylon Locknut (34). Do not
overtighten the Locknut; the Roller must be able
to roll easily.
9
39
38
39
34
Assemble the other three Rollers (39) to the
Squat Slider (38) in the same manner.
94
39
10. Orient the Squat Slider (38) as shown, and slide it
down onto the Squat Upright (4).
10
38
4
11. Insert the ends of two Weight Guides (42) without
holes into the indicated bracket on the Long Base
(101). Slide two Weight Bumpers (49) onto the
Weight Guides. Next, slide ten Weights (44) onto the
Weight Guides. Make sure that the Weights are
turned so the grooved sides of the Weights are
facing downward.
11
42
42
45
Press a Weight Tube Bumper (48) into the lower
end of a Weight Tube (43). Insert the Weight Tube
into the centers of the Weights (44). Make sure
that the Weight Tube is turned as shown.
Lubricate
“10” Decal
Groove
43
48
Lubricate the two outer holes in a Top Weight (45).
Slide the Top Weight onto the Weight Guides (42).
Make sure that the Top Weight is turned so the
grooved side is facing downward.
44
Apply a number “10” decal to the Top Weight (45) in
the location shown. Apply decals with the numbers
20 through 110 to the ten Weights (44).
“20” Decal
Assemble the other weight stack in the same
way.
“110” Decal
49
101
9
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Attach the Top Frame (6) between the Squat Upright
(4) and the Swivel Upright (5) with four M10 x 95mm
Bolts (92), the two Short Frame Plates (52), and two
M10 Nylon Locknuts (87) as shown. Do not tighten
the Bolts and Locknuts yet.
12
6
52
92
87
87
Attach the four Weight Guides (42) to the Top Frame
(6) with two M10 x 165mm Bolts (30) and two M10
Nylon Locknuts (87).
87
5
42
30
87
52
30
92
4
13. Press two 50mm x 75mm Inner Caps (58) into the
Top Frame (6) and the Butterfly Top Frame (7).
92
13
91
Attach the Butterfly Top Frame (7) to the Top Frame
(6) with two M10 x 70mm Bolts (85), two M10
Washers (91), and two M10 Nylon Locknuts (87).
Do not tighten the Locknuts yet.
58
7
6
91
87
91
85
Attach the Butterfly Top Frame (7) to the Butterfly
Upright (3) with two M10 x 95mm Bolts (92), two
M10 Washers (91), and two M10 Nylon Locknuts
(87).
58
14
Tighten all of the M10 Nylon Locknuts (87) used
in steps 4–13.
87
3
ARM ASSEMBLY
87
9
21
14. Open the parts bag labeled “ARM ASSEMBLY.”
Lubricate
18
10
Press three 40mm x 50mm Inner Caps (21) into the
Leg Lever (10).
21
Tab
Lubricate an M10 x 65mm Bolt (18) with grease.
Turn the Leg Lever (10) so that the welded tab is
on the indicated side, and attach the Leg Lever to
the Seat Upright (9) with the Bolt and an M10 Nylon
Locknut (87). Do not overtighten the Locknut;
the Leg Lever must be able to pivot easily.
21
15
7
15. Press a 50mm x 70mm Inner Cap (95) into the
Butterfly Frame (47). Attach the tethers on the two
“L”-pins w/Tether (60) to the Butterfly Frame with an
M4 x 20mm Self-tapping Screw (14).
95
87
107—Lubricate
14
Lubricate an M10 x 80mm Bolt (107) with grease.
Attach the Butterfly Frame (47) to the Butterfly Top
Frame (7) with the Bolt and an M10 Nylon Locknut
(87). Do not overtighten the Nylon Locknut; the
Butterfly Frame must be able to pivot easily.
60
60
47
10
Download from Www.Somanuals.com. All Manuals Search And Download.
16. Press a 40mm x 50mm Inner Cap (21) into the Right
Butterfly Arm (26). Wet the lower end of the Arm and
a Long Pad (54) with soapy water. Slide the Pad onto
the Arm.
16
Lubricate
100
70
26
87
Attach a Press Handle (27) to the Right Butterfly
Arm (26) with two M8 x 20mm Button Head Screws
(51). Slide the Long Pad (54) down so that the bot-
tom is flush with the lower end of the Arm. Wet the
Press Handle with soapy water. Slide a Long
Handgrip (28) onto the Press Handle. Press a
25mm Round Inner Cap (29) into the Press Handle.
21
29
51
25
54
28
Lubricate an M10 x 50mm Bolt (100) with grease.
Attach a Pivot Bracket (70) to the Right Butterfly
Arm (26) with the Bolt and an M10 Nylon Locknut
(87). Do not overtighten the Nylon Locknut; the
Pivot Bracket must be able to pivot easily.
Repeat this step with the Left Butterfly Arm (25).
27
56
17
17. Lubricate an M10 x 80mm Button Head Bolt (104)
and both sides of two Plastic Washers (56) with
grease. Attach the Right Butterfly Arm (26) to the
Butterfly Frame (47) with the Bolt, the two Plastic
Washers, two Butterfly Caps (57), two M10 Washers
(91), and an M10 Nylon Locknut (87) as shown.
Make sure that the recessed sides of the Plastic
Washers are fitted over the welded bushing in the
Butterfly Arm. Do not overtighten the Locknut;
the Butterfly Arm must be able to pivot easily.
104
26
91
57
47
57
91
25
87
Repeat this step with the Left Butterfly Arm (25).
CABLE ASSEMBLY
18.
IMPORTANT: Refer to the Cable Identification
18
Chart on page 26 for help identifying the
cables. Do not overtighten the bolts and
nuts attaching the pulleys. The pulleys must
be able to turn freely.
78
74
30
87
Locate and open the parts bags labeled “CABLE
ASSEMBLY” and “PULLEYS.”
Lubricate the M10 x 165mm Bolt (30) with grease.
Attach the Swivel Cage (76) to the Swivel Carriage
(46) with the Bolt and an M10 Nylon Locknut (87).
78
93
76
87
Locate the Swivel High Cable (74), which is
3213mm long and has a ball on one end and a
threaded bolt on the other end. Wrap the Cable
around a 90mm Pulley (78). Attach two Pulleys to
the Swivel Cage (76) with two M10 x 45mm Bolts
(93) and two M10 Nylon Locknuts (87).
46
11
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Route the Swivel High Cable (74) through the Swivel
Upright (5) and over a 115mm Pulley (119). Attach
the Pulley inside the Upright with an M10 x 65mm
Bolt (18), two M10 Washers (91), two 12mm
19
18
91
5
18
91
91
Spacers (89), and an M10 Nylon Locknut (87).
87
91
89
Attach an M10 x 65mm Bolt (18), two M10 Washers
(91), and an M10 Nylon Locknut (87) to the Swivel
Upright (5).
74
89
87
119
20. Remove the preattached 90mm Pulleys (78)
20
21
22
from the Small Pulley Plates (31).
74
Wrap the Swivel High Cable (74) over a 90mm
Pulley (78). Attach the Pulley and a Cable Trap (68)
to the second set of holes from the top of the Small
Pulley Plates (31) with an M10 x 50mm Bolt (100)
and an M10 Nylon Locknut (87). Make sure the
Cable Trap is turned to hold the Cable in the
groove of the Pulley.
87
100
31
68
78
31
21. Wrap the Swivel High Cable (74) over a 115mm
Pulley (119). Attach the Pulley inside of the indicat-
ed bracket on the Top Frame (6) with M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
6
93
87
74
119
22. Lift the Weight Tube (43) and the Top Weight (45)
closest to the Swivel Upright (5). Make sure that the
small pin on the Weight Tube is inside of the groove
under the Top Weight.
74
5
118
1
45
Insert a Weight Pin (50) into the stack of Weights
(44). Place a 50mm Washer (1) on top of the Weight
Tube (43). Tighten an M12 Nut (118) halfway onto
the end of the Swivel High Cable (74). Screw the
end of the Cable two full turns into the Weight Tube.
Then, tighten the M12 Nut against the Washer.
50
43
44
23
23. Locate the Swivel Cable (17), which is 2930mm
long and has an eyelet on each end. Attach the
Cable inside the Top Frame (6) with an M10 x
65mm Bolt (18), two M10 Washers (91), and an
M10 Nylon Locknut (87).
18
87
91
17
6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
24. Remove the preattached 90mm Pulleys (78)
24
from the Offset Double “U”-bracket (61).
Wrap the Swivel Cable (17) around a 90mm Pulley
(78). Attach the Pulley to the Offset Double “U”-
bracket (61) with an M10 x 45mm Bolt (93) and an
M10 Nylon Locknut (87).
17
78
93
61
87
25. Wrap the Swivel Cable (17) around a 90mm Pulley
(78). Attach the Pulley and a Cable Trap (68) to the
next to bottom hole in the Small Pulley Plates (31)
with an M10 x 50mm Bolt (100) and an M10 Nylon
Locknut (87). Make sure the Cable Trap is turned
to hold the Cable in the groove of the Pulley.
25
31
87
100
78
17
68
26. Wrap the Swivel Cable (17) around a 90mm Pulley
(78). Attach the Pulley and a Long Cable Trap (102)
to the bracket on the Swivel Upright (5) with an
M10 x 50mm Bolt (100) and an M10 Nylon Locknut
(87). Make sure the Cable Trap is turned to hold
the Cable in the groove of the Pulley.
26
100
5
102
87
17
78
27. Attach the end of the Swivel Cable (17) to the
bracket on the Swivel Carriage (46) with an M10 x
20mm Bolt (86) and an M10 Nylon Locknut (87).
27
46
86
17
87
28. Locate the Lat Cable (88), which is 2263mm long
and has a ball on one end and an eyelet on the
other. Route the eyelet end of the Cable up through
the Butterfly Top Frame (7) and around a 90mm
Pulley (78). Attach the Pulley inside of the Butterfly
Top Frame with an M10 x 65mm Bolt (101), two M10
Washers (91), two 12mm Spacers (89), and an M10
Nylon Locknut (87).
28
78
87
91
89
89
91
7
18
88
13
Download from Www.Somanuals.com. All Manuals Search And Download.
29. Wrap the Lat Cable (88) around a 90mm Pulley
(78). Attach the Pulley and a Long Cable Trap (102)
to the Top Frame (6) with an M10 x 50mm Bolt
(100) and an M10 Nylon Locknut (87). Make sure
the Cable Trap is turned to hold the Cable in the
groove of the Pulley.
29
88
78
87
102
100
6
30. Remove the preattached 90mm Pulleys (78)
30
from the Pulley Plates (63).
100
68
Wrap the Lat Cable (88) around a 90mm Pulley
(78). Attach the Pulley and a Cable Trap (68) to the
second set of holes from the top of the Pulley
Plates (63) with an M10 x 50mm Bolt (100) and an
M10 Nylon Locknut (87). Make sure the Cable
Trap is turned to hold the Cable in the groove of
the Pulley.
78
87
88
63
31. Attach the end of the Lat Cable (88) inside of the
Butterfly Top Frame (7) with an M10 x 65mm Bolt
(18), two M10 Washers (91), and an M10 Nylon
Locknut (87).
87
31
91
91
18
7
88
32. Locate the Butterfly Cable (69), which is the
shortest Cable. Attach the Cable to the Pivot
Bracket (70) on the Left Butterfly Arm (25) with an
M8 x 20mm Shoulder Bolt (103) and an M8 Nylon
Locknut (34).
32
34
69
103
70
25
33. Wrap the Butterfly Cable (69) over a “V”-pulley (55).
Attach the Pulley and a Long Cable Trap (102) to
the indicated bracket on the Butterfly Upright (3)
with an M10 x 60mm Bolt (59) and an M10 Nylon
Locknut (87). Make sure that the Long Cable
Trap is turned to hold the Cable in the groove of
the Pulley.
33
3
87
55
102
59
69
14
Download from Www.Somanuals.com. All Manuals Search And Download.
34. Remove the preattached 90mm Pulleys (78)
34
from the Double “U”-bracket (62).
69
93
Wrap the Butterfly Cable (69) under a 90mm Pulley
(78). Attach the Pulley to the Double “U”-bracket
(62) with an M10 x 45mm Bolt (93) and an M10
Nylon Locknut (87).
78
87
62
35. Wrap the Butterfly Cable (69) over a “V”-pulley (55).
Attach the Pulley and a Long Cable Trap (102) to
the other side of the bracket on the Butterfly Upright
(3) with an M10 x 60mm Bolt (59) and an M10
Nylon Locknut (87). Make sure that the Long
Cable Trap is turned to hold the Cable in the
groove of the Pulley.
35
59
102
69
3
55
87
36. Attach the Butterfly Cable (69) to the Pivot Bracket
(70) on the Right Butterfly Arm (26) with an M8 x
20mm Shoulder Bolt (103) and an M8 Nylon
Locknut (34).
36
103
70
69
34
26
37. Locate the Leg Lever Cable (75), which is
2505mm long and has an eyelet on one end and
a threaded pin on the other end. Route the eyelet
end of the Cable through the Seat Upright (9) and
attach it to the tab on the Leg Lever (10) with an
M8 x 20mm Shoulder Bolt (103) and an M8 Nylon
Locknut (34).
37
34
75
9
10
103
38. Attach a 90mm Pulley (78) inside of the Seat
Upright (9) with an M10 x 65mm Bolt (18), two M10
Washers (91), two 12mm Spacers (89), and an M10
Nylon Locknut (87), as shown.
38
9
91
89
75
78
87
91
18
89
15
Download from Www.Somanuals.com. All Manuals Search And Download.
39. Route the Leg Lever Cable (75) under a 115mm
Pulley (119). Attach the Pulley and a Large Cable
Trap (113) to the indicated side of the Butterfly
Upright (3) with an M10 x 95mm Bolt (92), an M10
Washer (91), and an M10 Nylon Locknut (87).
Make sure that the Large Cable Trap is turned to
hold the Cable in the groove of the Pulley.
39
119
92
113
3
75
87
91
40. Wrap the Leg Lever Cable (75) over a 90mm Pulley
(78). Attach the Pulley to the Double “U”-bracket
(62) with an M10 x 45mm Bolt (93) and an M10
Nylon Locknut (87).
40
93
62
87
75
78
41. Remove the preattached 90mm Pulley (not
41
shown) from the “U”-bracket (64).
75
90
34
75
64
Attach the end of the Leg Lever Cable (75) to the
“U”-bracket (64) with an M8 Washer (90) and an M8
Nylon Locknut (34). Note: Do not completely
tighten the Locknut; it should be threaded only
two turns onto the end of the Cable, as shown
in the inset drawing.
34
42. Locate the Swivel Low Cable (72), which is the
only remaining cable that has an eyelet on one
end and a ball on the other end. Route the eyelet
end of the Cable through the cage on the Long
Base (101) and through the Swivel Upright (5), as
shown. Make sure the Cable is over the short bar
inside the cage.
42
78
72
Cage
87
Attach a 90mm Pulley (78) to the indicated bracket
on the Long Base (101) with an M10 x 45mm Bolt
(93) and an M10 Nylon Locknut (87). Make sure
the Cable is in the groove of the Pulley.
101
5
93
43
43. Wrap the Swivel Low Cable (72) under a 90mm
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (101) with an M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
72
78
101
93
87
16
Download from Www.Somanuals.com. All Manuals Search And Download.
44. Wrap the Swivel Low Cable (72) over a 90mm
Pulley (78). Attach the Pulley to the Offset Double
“U”-bracket (61) with an M10 x 45mm Bolt (93) and
an M10 Nylon Locknut (87).
44
87
93
61
78
72
45. Wrap the Swivel Low Cable (72) under a 90mm
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (101) with an M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
45
72
78
87
101
93
78
46. Route the Swivel Low Cable (72) under the indicat-
ed stack of Weights (44).
46
72
87
Wrap the Swivel Low Cable (72) under a 90mm
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (101) with an M10 x 45mm
Bolt (93) and an M10 Nylon Locknut (87).
44
101
93
47. Wrap the Swivel Low Cable (72) over a 90mm
Pulley (78). Attach the Pulley and a Cable Trap (68)
between the indicated holes in the Pulley Plates
(63) with an M10 x 50mm Bolt (100) and an M10
Nylon Locknut (87). Make sure that the Cable
Trap is turned to hold the Cable in the groove of
the Pulley.
47
63
87
100
68
78
72
48. Wrap the Swivel Low Cable (72) under a 90mm
Pulley (78). Attach the Pulley to the indicated brack-
et on the Short Base (2) with an M10 x 45mm Bolt
(93) and an M10 Nylon Locknut (87).
48
78
72
93
87
2
17
Download from Www.Somanuals.com. All Manuals Search And Download.
49. Wrap the Swivel Low Cable (72) over a 90mm
Pulley (78). Attach the Pulley and a Cable Trap (68)
between the lower set of holes in the “U”-bracket
(64) with an M10 x 50mm Bolt (100) and an M10
Nylon Locknut (87). Make sure that the Cable
Trap is turned to hold the Cable in the groove of
the Pulley.
49
100
64
87
68
72
78
50. Attach the end of the Swivel Low Cable (72) inside
of the Short Base (2) with an M10 x 65mm Bolt
(18), two M10 Washers (91), and an M10 Nylon
Locknut (87).
50
87
91
2
72
91
18
51. Locate the Squat Cable (73), which is the only
remaining cable. Attach the eyelet end of the
Cable inside of the Long Base (101) with an M10 x
65mm Bolt (18), two M10 Washers (91), and an
M10 Nylon Locknut (87).
51
73
87
91
101
91
18
52. Wrap the Squat Cable (73) over a 90mm Pulley
(78). Attach the Pulley, a Cable Trap (68), and two
19mm Spacers (98) between the indicated brackets
on the Squat Slider (38) with an M10 x 85mm Bolt
(96) and an M10 Nylon Locknut (87). Make sure
that the Cable Trap is turned to hold the Cable
in the groove of the Pulley.
52
68
98
78
98
87
38
96
73
18
Download from Www.Somanuals.com. All Manuals Search And Download.
53. Wrap the Squat Cable (73) under a 90mm Pulley
(78). Attach the Pulley and a Cable Trap (68) to the
second set of holes from the top in the indicated
bracket on the Long Base (101) with an M10 x
50mm Bolt (100) and an M10 Nylon Locknut (87).
Make sure that the Cable Trap is turned to hold
the Cable in the groove of the Pulley.
53
73
68
78
87
100
101
54. Wrap the Squat Cable (73) over a 115mm Pulley
(119). Attach the Pulley to the indicated bracket on
the Top Frame (6) with an M10 x 45mm Bolt (93)
and an M10 Nylon Locknut (87).
54
6
87
93
119
73
55. Place a 50mm Washer (1) on top of the Weight Tube
(43) closest to the Squat Upright (4). Thread a M12
Nut (118) halfway onto the end of the Squat Cable
(73).
55
4
73
Lift the Weight Tube (43) and the Top Weight (45)
and make sure that the small pin on the Weight
Tube is inside of the groove under the Top Weight.
118
1
45
Hold the Weight Tube (43) and the Top Weight (45)
a few inches over the weight stack and insert the
Weight Pin (50). Screw the end of the Squat Cable
(73) two full turns into the Weight Tube. Then, tighten
the M12 Nut (118) against the 50mm Washer (1).
Remove the Weight Pin and set the Top Weight
back on the weight stack. Replace the Pin.
43
50
56
19
SEAT ASSEMBLY
23
109
56. Locate and open the parts bag labeled “SEAT
9
19
ASSEMBLY.”
Insert the Pad Tube (23) into the square hole in the
Seat Upright (9). Wet the Pad Tube with soapy
water. Slide the two Knee Pads (19) onto the Pad
Tube as shown. Press the two Knee Pad Caps
(109) into the ends of the Pad Tube.
20
10
109
Slide two Short Pads (20) onto the Leg Lever (10).
20
19
Download from Www.Somanuals.com. All Manuals Search And Download.
57. Press two 20mm x 40mm Inner Caps (116) and a
25mm x 40mm Square Inner Cap (117) into the
Seat Bracket (11).
57
16
Attach the Seat (16) to the Seat Bracket (11) with
two M6 x 16mm Screws (114), an M6 x 35mm
Screw (99), and an M6 Washer (97).
116
97
11
Turn the indicated Adjustment Handle (65) counter-
clockwise several turns to loosen it. Next, pull the
Handle and insert the Seat Bracket (11) into the
Seat Frame (8). Engage the Handle into one of the
holes in the Seat Bracket, and then turn the Handle
clockwise until it is tight.
99
116
114
117
8
65
116
58. Press two 20mm x 40mm Inner Caps (116) and a
25mm x 40mm Square Inner Cap (117) into the
Backrest Bracket (13).
58
3
114
15
Attach the Butterfly Backrest (15) to the Backrest
Bracket (13) with four M6 x 16mm Screws (114).
65
117
114
Turn the indicated Adjustment Handle (65) counter-
clockwise several turns to loosen it. Next, pull the
Handle and insert the Backrest Bracket (13) into the
Butterfly Upright (3). Engage the Handle into one of
the holes in the Backrest Bracket, and then turn the
Handle clockwise until it is tight.
13
116
59. Wet one end of the Squat Arm (32) with soapy
water. Slide a Short Pad (20) onto the Squat Arm
as shown.
59
20
20
32
Attach a Squat Handle (33) to the Squat Arm (32)
with two M8 x 20mm Button Head Screws (51).
Slide an Outer Cap w/Hole (111) onto the Squat
Handle and press it onto the end of the Squat Arm.
Wet the Squat Handle with soapy water. Slide an
200mm Handgrip (84) onto the Squat Handle.
51
51
33
Repeat this step with the other end of the Squat
Arm (32).
111
84
60. Attach the Squat Arm (32) to the Squat Bracket (37)
with two M10 x 65mm Carriage Bolts (110) and two
M10 Nylon Locknuts (87). Do not tighten the
Locknuts yet.
87
60
91
32
91
87
Finish attaching the Squat Arm (32) to the Squat
Bracket (37) with two M10 x 70mm Carriage Bolts
(106), two M10 Washers (91), and two M10 Nylon
Locknuts (87).
110
Tighten all of the M10 Nylon Locknuts (87) used
in this step.
106
37
20
Download from Www.Somanuals.com. All Manuals Search And Download.
61. Turn the Squat Backrest (35) so that the four screw
holes are closer to the bottom of the Squat
Backrest than the top. Attach the Squat Backrest to
the Squat Bracket (37) with four M6 x 16mm
Screws (114).
61
37
114
114
Fully tighten the Adjustment Knob (115) into the
Squat Bracket (37). Turn the knob on the
Adjustment Knob counterclockwise several times to
loosen it. Next, pull the Knob and slide the Squat
Bracket (37) down onto the Squat Slider (38).
Engage the Knob into one of the holes in the Squat
Slider, and then turn the Knob clockwise until it is
tight.
35
115
38
62. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENTS, beginning on the following page.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If
the cables are not properly installed, they may be damaged when heavy weight is used. See the
CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in
the cables, you will need to remove the slack by tightening the cables. See TROUBLESHOOTING on
page 25.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise
guide accompanying this manual to see how the weight system should be set up for various exercises. IMPOR-
TANT: When attaching the lat bar, row bar, or handle, make sure that the accessories are in the correct
starting position for the exercise to be performed. If there is any slack in the cables or chain as an exer-
cise is performed, the effectiveness of the exercise will be reduced.
CHANGING THE WEIGHT SETTING
To change the weight setting of either weight stack,
insert a Weight Pin (50) under the desired Weight
(44) until the bent end of the Weight Pin is touching
the Weights. Turn the bent end downward. The
weight setting of each weight stack can be changed
from 10 pounds to 110 pounds, in 10-pound incre-
ments. Note: Due to the cables and pulleys, the
amount of resistance at each exercise station may
vary from the weight setting. Use the WEIGHT
RESISTANCE CHART on page 24 to find the
approximate amount of resistance at each weight
station.
50
44
ATTACHING THE ACCESSORIES TO THE HIGH
PULLEY STATION OR THE LOW PULLEY STATION
Attach the Lat Bar (79) to the Lat Cable (88) with a
Cable Clip (83). For some exercises, the Chain (81)
should be attached between the Lat Bar and the Lat
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Lat Cable so the
Lat Bar is in the correct starting position for the
exercise to be performed.
88
83
81
83
The Lat Bar (79) can be attached to the Swivel Low
Cable (not shown) in the same way.
79
The Row Bar (not shown), the Handle (not shown), or
Ab Strap (not shown) can be attached to the Lat Cable
(88) or the Swivel Low Cable (not shown) in the same
way.
CONVERTING THE BUTTERFLY ARMS
To use the Butterfly Arms (25, 26) as butterfly arms,
insert the “L”-pins w/Tethers (60) into the butterfly holes
in the Butterfly Upright (3).
60
Butterfly
Holes
To use the Butterfly Arms (25, 26) as press arms, insert
the “L”-pins w/Tethers (60) into the press holes in the
Butterfly Frame (47).
3
26
47
Make sure that both “L”-pins w/Tethers (60) are fully
inserted into the same set of holes before perform-
ing any exercise.
Press
Holes
25
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE SQUAT ARM, SEAT, OR
BUTTERFLY BACKREST
32
To adjust the height of the Squat Arm (32), first turn
the Adjustment Knob (115) on the Squat Bracket (37)
counterclockwise several turns to loosen it. Next, pull
the Handle and slide the Squat Bracket up or down to
the desired position. Engage the Handle into one of
the holes in the Squat Slider (not shown), and then
turn the Handle clockwise until it is tight.
15
16
65
37
The height of the Seat (16), the position of the
Butterfly Backrest (15), and the Swivel Carriage (not
shown) can be adjusted in the same way using the
three Adjustment Handles (65).
115
65
ADJUSTING THE SQUAT KNEE REST
To use the Squat Knee Rest (41), pivot it down to the
position shown and insert the Pin w/Tether (112) into
the holes in the Squat Knee Rest and the Long Base
(101).
112
101
41
When the Squat Knee Rest (41) is not in use, pivot it
up to a vertical position and then insert the Pin
w/Tether (112) into the hole in the Long Base (101).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WEIGHT RESISTANCE CHART
The chart below shows the approximate weight resistance at each weight station. “Top” refers to the 10-pound
top weight. The other numbers refer to the 10-pound weight plates. The butterfly arm resistance listed is the
resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differ-
ences in individual weight plates as well as friction between the cables, pulleys, and weight guides.
WEIGHT
HIGH
PULLEY
(lbs.)
LOW
PULLEY
(lbs.)
LEG
LEVER
(lbs.)
BUTTERFLY
ARM
PRESS
ARM
(lbs.)
SQUAT
STATION
(lbs.)
SWIVEL
STATION
(lbs.)
(lbs.)
Top
1
14
25
14
25
22
35
17
26
24
39
59
16
26
87
2
38
36
53
36
55
116
136
170
192
203
223
239
254
270
39
3
48
44
67
45
70
52
4
61
60
91
54
89
59
5
68
70
111
122
148
160
184
190
63
104
118
136
154
167
187
74
6
80
80
71
84
7
96
91
80
90
8
101
112
122
104
111
122
91
104
116
122
9
100
108
10
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-
ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is
slack in the cables before resistance is felt, the cables should be tightened. To tighten the cables, first insert the
weight pins into the centers of the weight stacks. Slack can be removed from the cables in several ways:
See drawing 1. To tighten the Squat Cable (73) or the Swivel
High Cable (not shown), first loosen the M12 Nut (118) on
1
the end of the Cable, away from the 50mm Washer (1).
Screw the end of the Cable farther into the Weight Tube (43).
Then, retighten the Nut against the Washer.
73
118
1
43
See drawing 2. To further tighten the Squat Cable (73), first
remove the M10 Nylon Locknut (87), the M10 x 50mm Bolt
(100), Cable Trap (68), and 90mm Pulley (78) from the indi-
cated bracket on the Long Base (101). Reattach the Pulley
and Cable Trap between a lower set of holes with the Bolt
and Nylon Locknut.
2
68
87
73
78
101
100
See drawing 3. To tighten the other five cables, first remove
the upper or lower M10 Nylon Locknut (87), M10 x 50mm
Bolt (100), 90mm Pulley (78), and Cable Trap (68) from the
Pulley Plates (63) or Small Pulley Plates (not shown).
Reattach the Pulley and the Cable Trap between a set of
holes closer to the center of the Pulley Plates with the Bolt
and Locknut.
3
63
100
68
See drawing 4. To remove additional slack, first remove the
M10 Nylon Locknut (87), M10 x 50mm Bolt (100), 90mm
Pulley (78), and Cable Trap (68) from the “U”-bracket (64).
Reattach the Pulley and the Cable Trap between the higher
set of holes in the “U”-bracket with the Bolt and Locknut.
87
78
4
Slack can also be removed from the cables by tightening the
M8 Nylon Locknut (34) at the end of the Leg Lever Cable
(75). To do this you may need to remove the 90mm Pulley
(78) from the “U”-Bracket (64).
75
100
34
64
87
68
78
Do not overtighten the cables. If the cables are overtight-
ened, the top weights will be lifted off the weight stacks.
If a cable slips off the pulleys repeatedly, it may have
become twisted. Remove the cable and re-install it. If the
cables need to be replaced, see ORDERING REPLACE-
MENT PARTS on the back cover of this manual.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE DIAGRAMS
The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-
grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams
show the routes of the cables. Use the diagrams to make sure that the cables have been assembled correctly.
IMPORTANT: If the cables have not been correctly routed, the weight system will not function properly
and damage may occur.
Cable Identification Chart
Butterfly Cable (69)—1475mm
Swivel Low Cable (72)—5207mm
Squat Cable (73)—4425mm
Swivel High Cable (74)—3213mm
Leg Lever Cable (75)—2505mm
Lat Cable (88)—2267mm
Swivel Cable (17)—2930mm
Swivel High Cable (74)
Lat Cable (88)
4
2
4
Squat Cable (73)
2
4
1
1
5
3
2
4
3
1
Butterfly
Cable (69)
3
5
5
2
3
1
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Leg Lever
Cable (75)
Swivel Low
Cable (72)
3
6
3
8
4
1
2
5
4
2
7
1
9
Swivel Cable (17)
1
3
5
2
4
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
• The MODEL NUMBER of the product (WESY39523)
• The NAME of the product (WEIDER® PRO 3650 weight system)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 194012 R0103A
Printed in China © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part from the PART LIST in the center of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts
bags, check to see if it has been pre-assembled.
Note: Assembly is divided into four stages: 1) frame assembly, 2) arm
assembly, 3) cable assembly, and 4) seat assembly. The hardware for
each stage is packaged in separate bags. WAIT UNTIL YOU BEGIN EACH
ASSEMBLY STAGE TO OPEN THE PARTS BAG LABELED FOR THAT
ASSEMBLY STAGE.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART—Model No. WESY39523
R0103A
12mm Spacer (89)
19mm Spacer (98)
50mm Washer (1)
Cable Clip (83)
M10 Washer (91)
M8 Washer (90)
115mm Pulley (119)
(Not shown to scale)
M6 Washer (97)
M4 Washer (120)
"V"-pulley (55)
(Not shown to scale)
M12 Nut (118)
90mm Pulley (78)
M10 Nylon Locknut (87)
(Not shown to scale)
M8 Nylon Locknut (34)
Download from Www.Somanuals.com. All Manuals Search And Download.
M10 x 50mm Bolt (100)
M10 x 60mm Bolt (59)
M10 x 65mm Bolt (18)
M10 x 45mm Bolt (93)
M6 x 35mm Bolt (99)
M10 x 65mm Carriage Bolt (110)
M10 x 70mm Bolt (85)
M10 x 20mm Bolt (86)
M8 x 20mm
Shoulder Bolt (103)
M10 x 70mm Carriage Bolt (106)
M10 x 80mm Button Head Bolt (104)
M8 x 20mm Button
Head Screw (51)
M4 x 20mm Self-
M10 x 80mm Bolt (107)
M8 x 85mm Bolt (94)
tapping Screw (14)
M6 x 16mm Screw (114)
M10 x 85mm Bolt (96)
M10 x 95mm Bolt (92)
M10 x 165mm Bolt (30)
Download from Www.Somanuals.com. All Manuals Search And Download.
40mm x 50mm Inner Cap (21)
50mm x 75mm Inner Cap (58)
38mm Square Inner Cap (67)
50mm x 70mm Inner Cap (95)
25mm Round Inner Cap (29)
50mm Square Inner Cap (105)
20mm x 40mm Inner Cap (116)
25mm x 40mm Inner Cap (117)
25mm Round Outer Cap (121)
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART LIST/EXPLODED DRAWING
FROM THE MANUAL.
SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WESY39523
R0103A
Key
Key
Key
No. Qty.
Description
No. Qty.
Description
No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
1
1
1
1
1
1
1
1
1
1
1
1
9
50mm Washer
Short Base
Butterfly Upright
Squat Upright
Swivel Upright
Top Frame
Butterfly Top Frame
Seat Frame
Seat Upright
Leg Lever
Seat Bracket
Upright Extension
Backrest Bracket
M4 x 20mm Self-
tapping Screw
Butterfly Backrest
Seat
Swivel Cable
M10 x 65mm Bolt
Knee Pad
45
46
47
48
49
50
51
2
1
1
2
4
2
8
Top Weight
88
89
90
91
92
93
94
95
1
6
1
33
13
13
4
Lat Cable
Swivel Carriage
Butterfly Frame
Weight Tube Bumper
Weight Bumper
Weight Pin
M8 x 20mm Button
Head Screw
Short Frame Plate
Foot Plate
12mm Spacer
M8 Washer
M10 Washer
M10 x 95mm Bolt
M10 x 45mm Bolt
M8 x 85mm Bolt
50mm x 70mm Inner
Cap
M10 x 85mm Bolt
M6 Washer
19mm Spacer
M6 x 35mm Screw
M10 x 50mm Bolt
Long Base
Long Cable Trap
M8 x 20mm Shoulder
Bolt
M10 x 80mm Button
Head Bolt
50mm Square Inner
Cap
M10 x 70mm
1
52
53
54
55
56
57
58
2
1
2
2
4
4
7
96
97
98
99
2
1
2
1
Long Pad
"V"-pulley
Plastic Washer
Butterfly Cap
50mm x 75mm Inner
Cap
M10 x 60mm Bolt
“L”-pin w/Tether
Offset Double
“U”-bracket
Double “U”-bracket
Pulley Plate
"U"-bracket
Adjustment Handle
Swivel Bushings
38mm Square Inner
Cap
100 10
101
102
103
1
4
3
15
16
17
18
19
20
21
1
1
1
9
2
4
5
59
60
61
2
2
1
104
105
106
2
1
2
Short Pad
40mm x 50mm Inner
Cap
Ab Strap
Pad Tube
62
63
64
65
66
67
1
2
1
3
2
1
22
23
24
25
26
27
28
29
1
1
1
1
1
2
2
2
Carriage Bolt
107
108
109
1
4
2
M10 x 80mm Bolt
Knee Rest Bumper
Knee Pad Cap
M10 x 65mm
Base Cap
Left Butterfly Arm
Right Butterfly Arm
Press Handle
Long Handgrip
25mm Round Inner
Cap
M10 x 165mm Bolt
Small Pulley Plate
Squat Arm
Squat Handle
M8 Nylon Locknut
Squat Backrest
135mm Handgrip
Squat Bracket
Squat Slider
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
7
1
2
1
1
1
1
1
1
1
22
1
1
1
1
3
2
4
Cable Trap
110 12
Butterfly Cable
Pivot Bracket
Long Frame Plate
Swivel Low Cable
Squat Cable
Swivel High Cable
Leg Lever Cable
Swivel Cage
Leg Lever Bumper
90mm Pulley
Lat Bar
Row Bar
Chain
Handle
Cable Clip
200mm Handgrip
M10 x 70mm Bolt
M10 x 20mm Bolt
M10 Nylon Locknut
Carriage Bolt
111
112
113
114 10
115
116
2
1
1
Outer Cap w/Hole
Long Pin w/Tether
Large Cable Trap
M6 x 16mm Screw
Adjustment Knob
20mm x 40mm Inner
Cap
25mm x 40mm Inner
Cap
M12 Nut
115mm Pulley
M4 Washer
25mm Round Outer
Cap
User’s Manual
Exercise Guide
Grease Package
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
3
2
1
2
8
1
4
1
1
4
8
1
4
2
20
1
4
117
2
118
119
120
121
2
4
3
2
Roller
Roller Bearing
Squat Knee Rest
Weight Guide
Weight Tube
Weight
#
#
#
1
1
2
1
72
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WESY39523
R0103A
Download from Www.Somanuals.com. All Manuals Search And Download.
|