UA
DVD / SA-CD CHANGER
LECTEUR DE DVD / SA-CD CHANGEUR
DV-C6760
OWNER’S MANUAL
MODE D’EMPLOI
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference
will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning
the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe
Ave. Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic
Industries Association's Consumer Electronics Group recommend you to avoid prolonged exposure from excessive
volume levels.
For Customer Use:
CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM
Read carefully the information located at the rear panel of
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING
UNDGÅ UDSÆTTELSE FOR STRÅLING
the player and enter below the Serial No. Retain this
information for future reference.
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL
ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
Model No.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE, ÄLÄ KATSO SÄTEESEEN
Serial No. __________________________
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN AVOID DIRECT EXPOSURE TO BEAM
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN
CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
This digital apparatus does not exceed the Class B limits for
T
E
L
S
T
L
C
S
L
L
L
S
I
K
P
radio noise emissions from digital apparatus as set out in the
Radio Interference Regulations of the Canadian Department
of Communications.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reason.
15 When not planning to use this unit for long
periods of time (i.e., vacation), disconnect the AC
power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING”
section on common operating errors before
concluding that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect the
AC power plug from the wall outlet.
Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, or cold. In a
cabinet, allow about 2.5cm (1 inch) of free space
all around this unit for adequate ventilation.
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in
an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit in a location where
foreign objects may fall onto this unit or where
this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or personal
injury.
3
4
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
5
When playing DTS encoded CDs, excessive noise will
be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer
should take proper precautions when the analog
stereo outputs of the player are connected to an
amplification system. To enjoy DTS Digital
Surround™ playback, an external 5.1-channel DTS
Digital Surround™ decoder system must be
connected to the digital output of the player.
– Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
6
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the
cover or attempt to service this device.
7
8
9
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use excessive force on switches, knobs
and/or cords.
DANGER
This unit emits visible laser radiation when open.
Avoid direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not
place your eyes close to the opening of the disc tray
and other openings or look inside.
10 When disconnecting the power cord from the
wall outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from
use of this unit with a voltage other than as
specified.
Be sure to place this unit on a level surface.
If not so, this unit will fail to work normlly at the
PLAYXCHANGE operation and cause damage to the
disc(s) and this unit itself.
LASER
Type
Wave length
Semiconductor laser GaAlAs
650 nm (DVD)
780 nm (VCD/CD)
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
Output Power
Beam divergence 60 degree
7 mW (DVD/VCD/CD)
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Special VCD & SVCD Features ........................................ 16
Playing a disc........................................................................................17
Playing a disc........................................................................................18
Special picture disc features .............................................. 18
Zoom picture......................................................................................19
Scan Effect.............................................................................................19
Introduction
Functional Overview
Rear Panel ................................................................................4
Preparation
Digital Connections ...............................................................6
Analog Connections...............................................................6
S-Video terminal <A>......................................................................7
Composite Video terminal <B>.................................................7
Component Video terminal <C>..............................................7
Programming disc tracks and discs.........................................20
OSD Language...................................................................................21
Screen Saver........................................................................................21
Sleep Timer..........................................................................................21
Audio Setup Menu............................................................... 22
Setting the analog output.............................................................22
Setting the Digital output.............................................................23
Speaker Setup.....................................................................................23
CD Upsampling.................................................................................23
Night Mode..........................................................................................24
Video Setup Menu................................................................ 24
TV Type.................................................................................................24
Progressive............................................................................................25
Picture Setting.....................................................................................25
Selecting the black level (U.S.A. model only)...................26
Preference Setup Menu ...................................................... 26
Audio, Subtitle, Disc Menu..........................................................26
PBC (Playback Control)................................................................27
MP3/JPEG Menu................................................................................27
Changing the Password.................................................................28
Restoring to original settings......................................................28
Getting Started
Setting the OSD Language.............................................................9
Disc Operations
Basic Playback........................................................................12
General Operation...............................................................12
Pausing playback................................................................................12
Selecting track/chapter...................................................................12
Searching backward/forward......................................................12
Stopping playback.............................................................................12
Selecting various repeat/shuffle functions.......................13
Repeat.....................................................................................................13
Repeating a section within a chapter/track........................13
Shuffle (not for DVD/VCD/SVCD)........................................13
Operations for video playback (DVD/VCD/SVCD).....14
Using the Disc Menu......................................................................14
Zooming in...........................................................................................14
Resuming playback from the last stopped point.............14
On-Screen Display (OSD)..........................................................14
Special DVD Features..........................................................15
Playing a Title ......................................................................................15
Camera Angle.....................................................................................15
Audio.......................................................................................................15
Subtitles..................................................................................................15
Language Code .......................... 29
Troubleshooting ........................ 31
Glossary ...................................... 33
Specifications ............................. 34
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing this unit. This
Owner’s Manual explains the basic
operation of this unit.
– Do not use a disc printed on its surface by
a commercially available label printer.
Cleaning discs
Region Codes
• When a disc becomes dirty, clean it
with a cleaning cloth. Wipe the disc
from the centre out. Do not wipe in a
circular motion.
• Do not use solvents such as benzine,
thinner, commerciallyavailablecleaners,
or antistatic spray intended for analog
records.
DVD discs must be labeled for
ALL
ALL regions, Region 1 (U.S.A
model) or Region 4 (Australia
model) in order to play on this
Player. You cannot play Discs that
are labeled for other regions.
1
4
Supplied accessories
– Remote control
– Batteries (two AA size) for remote
control
– Audio/Video cable
– Owner’s Manual
Patent information
Manufactured under license from
Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D
symbol are trademarks of Dolby
Laboratories.
Notes about discs
“DTS” and “DTS Digital
Surround” are registered
trademarks of Digital Theater
Systems, Inc.
– This unit is designed for use with Super
Audio CD (SA-CD), DVD-Video, Video CD,
Super Video CD, Audio CD, CD-R, CD-RW,
DVD+RW, DVD+R, DVD-R and DVD-RW.
DivX, DivX Certified, and
associated logos are trademarks
of DivXNetworks, Inc and are
used under license.
This unit can play:
– MP3, picture (Kodak, JPEG) files on CD-
R(W).
– JPEG/ISO 9660 format
– Maximum 30 characters display.
– DivX disc on CD-R[W]/DVD+R[W]/
DVD-R[W] (3.11, 4.x and 5.x)
– CD-R and CD-RW cannot be played unless
finalized.
®
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and
other rights owners. Use of this copyright
– Some discs cannot be played depending on
the recording conditions such as PC
environment and application software. The
characteristics and condition of the discs;
materials, scratches, curvature, and etc.,
may result in failure.
protection technology must be authorized by
Macrovision Corporation, and is intended for home
and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
– Be sure to use only CD-R and CD-RW discs
made by reliable manufacturers.
– Do not use any non standard shaped discs
(heart, etc.)
– Do not use disc with tape, scals, or paste on
it, damage to the unit may result.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
Front Panel
STANDBY/ON
– turns on this unit or sets it to the
standby mode
/OPEN/CLOSE
– to open/close the disc tray
Disc tray
– load up to 5 discs on the disc tray
DISPLAY
– shows the current status of the
player
S/Q
– search backward* / go to a
previous chapter or track
LEDs
R/T
– search forward* / go to the next
chapter or track
– LED lights up when the
corresponding feature is set to ON
DISC (1, 2, 3, 4, 5)/LEDs
B/;PLAY/PAUSE
– to start or interrupt playback
– to select and directly playback the
preferred disc / each LED flashes
green when button is selected
9STOP
– to stop playback
PLAYXCHANGE
– to change another disc(s) during
playback
* Press button for about two seconds.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
Rear Panel
COMPONENT video outputs
– connect to an AV receiver with Y PB/
CB PR/CR inputs
AC Power Cord
– connect to a standard AC outlet
DIGITAL OUT - OPTICAL
– connect to OPTICAL input of your
AV receiver
AUDIO OUT - 6CH DISCRETE
– connect to 6CH INPUT inputs of your
AV receiver
DIGITAL OUT - COAXIAL
– connect to COAXIAL input of
your AV receiver
AUDIO OUT - MIXED 2CH
– connect to AUDIO inputs of your AV
receiver or stereo system
VIDEO OUT - VIDEO
– connect to VIDEO (composite) input of
your AV receiver
VIDEO OUT - S VIDEO
– connect to S VIDEO input of your AV
receiver
Caution: Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
Remote Control
|
DISC SKIP
B/
– select another disc
– turn this unit ON or go to
standby-on mode
PAGE
– not used with this model
0-9 numeric keypad
– select numbered items in a
menu
DIMMER
– select 3 different
brightnesses for the display
SOUND MODE
– selects the required sound
mode: Stereo, Virtual Surround
or Multi-channel / change
SA-CD playback area
ON SCREEN
– access or remove player’s
On Screen Display menu
SETUP
– access or remove player’s
setup menu
TOP MENU/RETURN
– display the top-level disc
menu (DVD) / go back to
previous menu (VCD)
T
– search forward* / next
chapter or track
MENU
– access menu of a disc (DVD)
/ switch PBC on/off (VCD)
SUBTITLE
– subtitle language selector
ANGLE
– select DVD camera angle
1 2 3 4
– (left/right/up/down) select an
item in the menu
ZOOM
– enlarge video image
ENTER/OK
– acknowledge menu selection
AUDIO
– audio language and format
selector / change Hybrid SA-
CD playback layer
S
– search backward* / go to a
previous chapter or track
REPEAT
– repeat chapter, track, title,
disc, all discs
STOP ( 9)
– stop playback
A-B
PLAY ( B)
– repeat a specific segment
– start playback
SHUFFLE
– play tracks in random order
PAUSE ( ;)
– pause playback temporarily /
frame-by-frame playback
SCAN
– play the first 6 seconds or
less of each track / chapter
within a disc
* Press and hold button for about two seconds.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Notes:
General Notes on connections
– If the audio format of the digital output
does not match the capabilities of your
receiver, the receiver will produce a strong,
distorted sound or no sound at all. Make
sure to select the appropriate audio format
at menu screen included on the disc.
Pressing AUDIO once or more may change
not only audio languages but also audio
formats, and the selected format appears
for several seconds on the status window.
– SA-CD audio signal is not output from
DIGITAL OUT jacks.
Never make or change connections with
the power switched on.
• Depending on the equipment you wish
to connect, there are various ways you
could connect this unit. Possible
connections are shown in the following
drawings.
• Please refer to the manuals of other
equipment as necessary to make the
best connections.
• Do not connect this unit via your VCR.
The video quality could be distorted by
the copy protection system.
• Do not connect this unit’s audio out
jack to the phono in jack of your audio
system.
– If you wish to enjoy Dolby Digital, DTS, and
MPEG you must connect this unit to the AV
receiver that support those.
Analog Connections
This player has two types of analog output
jacks.
Digital Connections
This unit has COAXIAL and OPTICAL
digital out jacks. Connect one or both of
them to your AV receiver equipped with
Dolby Digital, DTS, or MPEG decoder
using each specific cable (separate
purchase).
6CH DISCRETE jacks
To reproduce multi-channel Super audio
CD, connect these jacks to your AV
receiver’s multi channel input jacks using
commercially available audio pin cables.
C
O
AV receiver
Speakers
COAXIAL OPTICAL
IN IN
FRONT
CENTER SUBWOOFER SURROUND
R
L
R
L
AV receiver
Speakers
You will need to set this unit’s digital
output to ALL (see page 23
“DIGITAL OUTPUT”).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
commercially available S-video cable.
Receiver (and TV) with S-video input is
required.
MIXED 2CH jacks
Use audio/video cable supplied with this
player to connect the L (left) and R (right)
jacks to corresponding input jacks of your
audio equipment such as Stereo amplifier.
You can connect a subwoofer to the
SUBWOOFER jack.
Composite Video terminal <B>
Use audio/video cable supplied with this
unit when connecting the player to a TV.
Component Video terminal <C>
Component video connection achieves
high fidelity in reproducing colors (better
performance than S-video connection),
separating video signal into luminance (Y,
terminal color-coded as green), and color
difference (Pb, blue/Pr, red). Use
R
L
commercially available coaxial cables.
Receiver (and TV) with component input is
required. Observe the color of each jack
when connecting. If your receiver does not
have component output jacks, connecting
the player’s component output directly to
your TV’s component input can reproduce
better video image.
R
L
Stereo
amplifier
1
CD/DVD
Subwoofer
R
L
Right
speaker
Left
speaker
Video Connections
If your AV receiver has video output jacks,
connect your receiver (and then to your
TV) so that you can use one TV for several
different video sources (LD, VCR etc.) by
simply switching the input source selector
of your receiver.
The player has three types of video output
jacks. Use one of them in accordance with
the input jacks of the equipment to be
connected.
V
S
<A>
<B>
<C>
PR/CR
PB/CB
Y
S VIDEO
VIDEO
COMPONENT
VIDEO
AV receiver
S VIDEO
OUT
COMPONENT
VIDEO OUT OUT
VIDEO
S VIDEO
IN
COMPONENT
VIDEO IN
VIDEO
IN
S-Video terminal <A>
S (separate) video connection achieves a
clearer picture than composite video
connection by separating color and
luminance when transmitting signals. Use
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Step1: Inserting batteries
into the Remote Control
Step2: Turning on the power
1 Connect the AC power cord to the power
outlet.
2 Turn on the TV and your AV receiver.
3
3 Select the appropriate input source at the
AV receiver that was used to connect to
this unit. Refer to the equipment owner’s
manual for detail.
1
2
4 Turn this unit on.
1 Open the battery compartment.
5 Set the TV to the correct Video IN
channel. (e.g. EXT1, EXT2, AV1, AV2,
AUDIO/VIDEO, etc. Refer to your TV
owner’s manual for detail)
2 Insert two batteries type R06 or AA,
following the indications (+ –) inside the
compartment.
➜ The front display lights up and the
default screen appears on the TV.
3 Close the cover.
Using the remote control
Step3: Selecting the color
system that corresponds to
your TV
Remote control
sensor
This DVD Player is compatible with both
NTSC and PAL. Select the color system
that matches your TV.
Point the remote control
at the sensor, within
approximately 6 m
(20 feet) of the unit.
VIDEO SETUP PAGE
TV TYPE
PAL
TV DISPLAY
NTSC
MULTI
PROGRESSIVE
PICTURE SETTING
BLACK LEVEL
CLOSED CAPTION
Handling the remote control
• Do not spill water or other liquids on
the remote control.
• Do not drop the remote control.
• Do not leave or store the remote
control in the following types of
conditions:
1 Press SETUP.
2 Press 2repeatedly to select {VIDEO
SETUP PAGE}.
3 Press 34to highlight {TV TYPE}, then
press 2.
– high humidity such as near a bath
– high temperature such as near a heater
or stove
– extremely low temperature
– dusty places
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
4 Press 34to highlight one of the options
Step4: Setting language
below:
preference
PAL
Select this if the connected TV is PAL
system. It will change the video signal of a
NTSC disc and output in PAL format.
You can select your own preferred
language settings.This DVD Player will
automatically switch to the language for
you whenever you load a disc. If the
language selected is not available on the
disc, the disc’s default language will be used
instead. The OSD language in the system
menu, will remain once selected.
NTSC
Select this if the connected TV is NTSC
system. It will change the video signal of a
PAL disc and output in NTSC format.
MULTI
Select this if the connected TV is
compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
Setting the OSD Language
GENERAL SETUP PAGE
5 Select an item and press ENTER/OK.
DISC LOCK
PROGRAM
Helpful Hint:
OSD LANGUAGE
SCREEN SAVER
SLEEP
ENGLISH
FRANÇAIS
ESPAÑOL
– Before changing the current TV
Standard setting, ensure that your TV
supports the ‘selected TV Type’
system.
DIVX(R) VOD CODE
– If there is not proper picture on your
TV, wait for 15 seconds for auto
recover.
(U.S.A. model)
1 Press SETUP.
2 Press 12to select {GENERAL SETUP
PAGE}.
CHANGING PAL TO NTSC
1. ENSURE THATYOUR TV SYSTEM SUPPORTS
NTSC STANDARD.
2. IF THERE IS A DISTORTED PICTURE
DISPLAYED ON THE TV, WAIT 15 SECONDS
FOR AUTO RECOVER.
3 Press 34to highlight {OSD LANGUAGE},
then press 2.
4 Press 34to select a language and press
ENTER/OK.
OK
CANCEL
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Setting the Audio, Subtitle and
Disc menu language
Step5: Setting the speaker’s
channels
You can adjust the delay times (center and
surround only) and volume level for
individual speakers. These adjustments let
you optimize the sound according to your
surroundings and setup.
PREFERENCE PAGE
AUDIO
ENGLISH
SUBTITLE
DISC MENU
PARENTAL
PBC
CHINESE(SIMP)
FRENCH
SPANISH
IMPORTANT!
The speaker settings only available
on Multi-channel audio outputs.
PORTUGUESE
POLISH
MP3/JPEG NAV
PASSWORD
DEFAULT
ITALIAN
TURKISH
1 Press SETUP.
2 Press 2repeatedly to select {AUDIO
1 Press STOP 9twice, then press SETUP.
SETUP PAGE}.
2 Press 2repeatedly to select
3 Press 34to highlight {SPEAKER SETUP},
then press 2.
{PREFERENCE PAGE}.
below at a time, then press 2.
– ‘AUDIO’ (disc’s soundtrack)
– ‘SUBTITLE’ (disc’s subtitles)
– ‘DISC MENU’ (disc’s menu)
AUDIO SETUP PAGE
ANALOG OUTPUT
DIGITAL AUDIO
SPEAKER SETUP
CD UPSAMPLING
NIGHT MODE
4 Press 34to select a language and press
ENTER/OK.
If the language you want is not in the
list, then select {OTHERS},
then use the numeric keypad (0-9) on
the remote to enter the 4-digit language
code (see page 29 “Language Code”) and
press ENTER/OK.
SPEAKER SETUP
FRONT SPEAKER
CENTER SPEAKER
SURROUND SP
SUBWOOFER
SPEAKERS VOLUME
SPEAKERS DELAY
5 Repeat steps 3–4 for other language
4 Enter its submenu by pressing 2.
settings.
5 Press 34to highlight one of the options
below at a time, then press 2.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
{FRONT SPEAKER, CENTER
SPEAKER, SURROUND SP}
{SPEAKERS DELAY}
Delay times setting in relation to the
listening position/distance for center and
surround speakers (0 MS~15 MS).
OFF (only for CENTER and
SURROUND)
When no speaker is connected.
SPEAKERS DELAY SETUP
LARGE
CENTER
0 MS
When connected speakers can produce
low frequency signals below 120 Hz.
0 MS
0 MS
SURROUND L
SURROUND R
SMALL
When connected speakers cannot
produce low frequency signals below
120 Hz.
6 Press 12to adjust the setting that best
suit your surround sound needs.
7 Press ENTER/OK to confirm.
{SUBWOOFER}
ON
When a subwoofer is connected.
Helpful Hints:
– Use the longer delay time settings when the
surround speakers are closer to the listener
than the front speakers.
– The test tone will be automatically
generated to help you judge the sound level
of each speaker.
OFF
When no subwoofer is connected.
{SPEAKERS VOLUME}
Volume level setting for individual
speakers (–6 dB ~ +6 dB).
SPEAKERS VOLUME SETUP
FRONT LEFT
FRONT RIGHT
0dB
0dB
0dB
0dB
CENTER
SUBWOOFER
0dB
0dB
SURROUND L
SURROUND R
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
IMPORTANT!
• When the disc tray is open, pressing
PLAY B, OPEN/CLOSE /,
PLAYXCHANGE, DISC (1, 2, 3, 4,
5) will close the disc tray automatically.
– If the inhibit icon ( or X) appears
on the TV screen when a button is
pressed, it means the function is
not available on the current disc or
at the current time.
– Depending on the DVD or VIDEO
CD, some operations may be
different or restricted.
– Do not push on the disc tray or put
any objects other than disc on the
disc tray. Doing so may cause the
disc player malfunction.
General Operation
Unless otherwise stated, all operations
described are based on Remote Control
use.
Pausing playback
1 During playback, press PAUSE ;.
➜ Playback will pause and sound will be
muted.
Basic Playback
1 Press STANDBY/ON on the front panel.
2 Press PAUSE ;again to select the next
picture frame.
2 Press OPEN/CLOSE /on the front
panel to open disc loading tray.
3 To resume normal playback, press
PLAY B.
3 Place the chosen discs in the tray, with the
label facing up.
Selecting track/chapter
4 Press PLAY B.
➜ The disc tray closes and playback starts
automatically with all the loaded discs
on the tray in sequence.
• Press S/ Tor use the numeric
keypad (0-9) to key in a track/chapter
number.
➜ If repeat mode is active, pressing S/
Twill replay the same track/chapter.
5 To stop playback, press STOP 9.
Searching backward/forward
• Press and hold S/ T, then press
PLAY Bto resume normal playback.
➜ While searching, pressing S/ T
again will increase the search speed.
Note:
• To playback a specific disc directly,
press DISC SKIP repeatedly on the
remote control or one of the DISC (1,
2, 3, 4, 5) on the front panel.
®
– For MP3, WMA, DivX , the search
function allows you to search within the
currently playing track.
• Press PLAYXCHANGE on the front
panel to open the disc tray and reload
or unload any discs without interrupting
current disc playback.
Stopping playback
• Press STOP 9.
• Playback will stop after all discs have
been played.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
Repeating a section within a
chapter/track
Selecting various repeat/shuffle
functions
1 While playing a disc, press A-B at your
chosen starting point.
Repeat
2 Press A-B again at your chosen end point.
➜ The section A and B can be set only
within the same chapter/track.
➜ The section will now repeat
continuously.
Repeat chapter/title/disc (DVD)
Each time you press REPEAT, the front
display changes as follows;
CHAPTER
REPEAT OFF ALL DISC
TITLE
DISC
3 To exit the sequence, press A-B.
CHAPTER*: repeat the current
chapter
Shuffle (not for DVD/VCD/
SVCD)
With the Shuffle function, you can play
tracks in random order.
TITLE: repeat the current title
DISC*: repeat the entire disc
ALL DISC: repeat all discs loaded on
the tray
1 During playback, press SHUFFLE
repeatedly to select SHUFFLE DISC,
SHUFFLE ALL DISC, or SHUFFLE OFF.
➜ The selected mode appears on the
display for several seconds.
REPEAT OFF: exit repeat mode
* This feature may not be available with some
discs.
Repeat track/disc (except DVD)
Each time you press REPEAT, the front
display changes as follows;
• In SHUFFLE DISC mode, all tracks on
the disc currently playing are played in
random order. For Hybrid SA-CDs,
tracks on the SA-CD layer are played by
default (see page 17).
TRACK
DISC
REPEAT OFF
ALL DISC
• In SHUFFLE ALL DISC, tracks from all
discs are played in random order:
– If the disc currently playing is a CD, only
tracks from CDs and the CD layer of
SA-CDs will be played.
TRACK: repeat the current track
DISC: repeat the entire disc
ALL DISC: repeat all discs loaded on
the tray
REPEAT OFF: exit repeat mode
– If the disc currently playing is in SA-CD
®
Note:
(SA-CD layer), MP3, WMA, DivX ,
– When only one disc is available on the disc
tray, continuous playback will apply when
ALL DISC is selected.
tracks on the disc currently playing are
played in random order. When all the
tracks on that disc have been played,
shuffle playback continues with the next
disc.
Helpful Hint:
– For VCD, repeat playback is not possible if
the PBC mode is switched on.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
On-Screen Display (OSD)
Operations for video playback
(DVD/VCD/SVCD)
OSD menu shows the disc playback
information (for example, title or chapter
number, elapsed playing time, audio/
subtitle language), a number of operations
can be done without interrupting disc
playback.
Using the Disc Menu
Depending on the disc, a menu may appear
on the TV screen once you load in the disc.
1 During playback, press ON SCREEN.
➜ A list of available disc information
appears on the TV screen.
To select a playback feature or item
• Use 1234or numeric keypad
(0-9) on the remote, then press
ENTER/OK to start playback.
DVD
MENU
To access or remove the menu
TITLE
02/14
02/14
5.1CH
ENG
• Press MENU on the remote.
CHAPTER
AUDIO
SUBTITLE
Zooming in
BITRATE
This function allows you to enlarge the
picture on the TV screen and to pan
through the enlarged picture.
VCD/SVCD
1 During playback, press ZOOM repeatedly
to display the picture with different scales.
➜ Use 1234to pan through the
enlarged picture.
MENU
TRACK
02/14
DISC TIME
TRACK TIME
REPEAT
0:49:17
0:03:43
OFF
➜ Playback will continue.
BITRATE
2 Press ZOOM repeatedly to return to the
original size.
2 Press 34to view the information and
press ENTER/OK to access.
Resuming playback from the last
stopped point
Resume playback of the last 10 discs is
possible, even if the disc was ejected or the
power switched off.
3 Use the numeric keypad (0-9) to input
the number/time or press 34to make the
selection, then press ENTER/OK to
confirm.
➜ Playback will change to the chosen time
or to the selected title/chapter/track.
• Load one of the last 10 discs.
➜ “LOADING” appears.
• Press PLAY Band the disc will be
played back from the last point.
Title/Chapter/Track selection (DVD/
VCD)
1 Press 34to select {TITLE} or
To cancel resume mode
• In stop mode, press STOP 9again.
{CHAPTER} (DVD) or {TRACK} (VCD).
2 Press ENTER/OK.
3 Select a title, chapter or track number
using the numeric buttons.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
Time Search (DVD/VCD)
Special DVD Features
1 Press 34to select {TT TIME} or {CH
TIME} (DVD) or {TRACK TIME} or {DISC
TIME} (VCD).
Playing a Title
➜ {TT TIME} refers to the total time of the
current title, and the {CH TIME} refers
to the total time of the current chapter.
1 Press MENU.
➜ The disc title menu appears on the TV
screen.
2 Press ENTER/OK.
2 Use 1234or numeric keypad (0-9)
3 Enter hours, minutes and seconds from left
to right using the numeric buttons. (e.g.
0:34:27)
to select a play option.
3 Press ENTER/OK to confirm.
Audio/Subtitle/Angle (DVD)
Camera Angle
• Press ANGLE repeatedly to select
different desired angle.
You can change {AUDIO}, {SUBTITLE} or
{ANGLE} if available on the disc you are
playing.
1 Press 34to select {AUDIO}, {SUBTITLE}
Audio
or {ANGLE}.
Changing the Audio Language and/or
format
• Press AUDIO repeatedly to select
2 Press ENTER/OK.
3 For Audio and Subtitle,
Press 34to highlight your selection and
press ENTER/OK.
different audio languages.
or
For Angle,
Subtitles
• Press SUBTITLE repeatedly to select
Select an angle using the numeric buttons.
different subtitle languages.
Repeat/Time Display (DVD/VCD)
1 Press 34to select {REPEAT} or {TIME
DISP.}.
2 Press ENTER/OK.
3 Press 34to highlight your selection and
press ENTER/OK.
Time display (CD)
TOTAL ELAPSED
SINGLE REMAIN
TOTAL REMAIN
SINGLE ELAPSED
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
DISC INTERVAL
Special VCD & SVCD Features
This function is used to divide a disc into
six parts by regular intervals and display
them on one page to preview the whole
disc.
Playback Control (PBC)
For VCD with Playback Control
(PBC) feature (version 2.0 only)
• Press MENU to toggle between ‘PBC
ON’ and ‘PBC OFF’.
➜ If you select ‘PBC ON’, the disc menu (if
available) will appear on the TV.
➜ Use the S/ Tor the numeric
keypad (0-9) to select a play option.
• During playback, pressing TOP
MENU/RETURN will return to the
menu screen (if PBC is on).
TRACK INTERVAL
This function is used to divide a single track
into six parts by regular intervals and
display them on one page to help you
preview the selected track.
If you want to skip the index menu
and playback directly from the
beginning,
• Press MENU on the remote control to
switch to PBC off.
(example for 6 thumbnail pictures display)
4 Use 1234to select a track or use
numeric keypad (0-9) to input the
selected track number next to {SELECT}.
5 Press S/ Tto open the previous or
next page.
Preview Function
6 Press ENTER/OK to confirm.
1 Press SCAN.
To quit preview function
• Use 1234to highlight {EXIT} and
press ENTER/OK to confirm.
2 Press 34to highlight {TRACK DIGEST},
{DISC INTERVAL} or {TRACK
INTERVAL}.
3 Press ENTER/OK to open one option.
To return to preview menu
• Use 1234to highlight {MENU} and
press ENTER/OK to confirm.
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
For CD
TRACK INTERVAL
• At stop mode, press SCAN on the
remote control.
TRACK DIGEST
This function will minimize the picture of
every track in order to display every six of
these tracks on the screen to help you
know the content of every track on the
disc.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
Playing a disc
SA-CD (Super Audio CD)
1 Load a disc.
The SA-CD standard is based on Direct
Stream Digital (DSD) technology. This
new direct-stream digital format
comprises a 1-bit system that has a digital
sampling frequency that is 64 times higher
than that of conventional audio CD.
There are three types of SA-CD discs:
single-layer, dual-layer and hybrid discs.
Each type may contain two areas of
recorded information: a High Quality
Stereo area and a High Quality Multi-
channel area.
– A single layer disc can contain both
information areas.
– A dual layer disc can contain both
information areas. Double the
information can be stored on the disc,
thanks to the second layer.
– A hybrid disc can contain both
information areas, and also a second,
standard CD layer, making it playable on
standard CD players.
Playback starts automatically.
➜ The TV screen will display the current
playing status and current playing track
list in the area.
2 Playback will stop at the end of the disc.
3 To stop playback, press STOP 9.
Changing SA-CD playback area
and layer
You can change the SA-CD playback area
by pressing the SOUND MODE button,
and change the playback layer by pressing
the AUDIO button.
• On hybrid discs (with SA-CD and CD
layers), the player will always start
playing the SA-CD layer (multi channel
area).
• You can change between SA-CD multi
channel and SA-CD stereo area by
pressing SOUND MODE (depending
on availability of the mode on the disc).
or
SA-CD Disc Types
Hybrid layer
1 Press 1and select the folder using
34, then Press ENTER/OK.
3 Press ENTER/OK to confirm.
Dual layer disc
disc
Single layer disc
HD layer
CD layer
HD layer
HD layer
• To switch between the SA-CD layer
and the CD layer, press the AUDIO
button while playback is stopped.
• The SA-CD indicator lights only when
the SA-CD layer is selected.
Hybrid SA-CD-Disc
1
CD layer that plays on any CD
player
– SA-CD Text is not supported.
– You can not change the Analog output
setting during SA-CD playback (see
page 22 “Audio Setup Menu”).
High Density layer containing:
- High Quality DSD Stereo
2
3
- High Quality DSD Multi-
channel
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
Helpful Hint:
Audio CD
– It may not be possible to play certain MP3/
JPEG/DivX disc due to the configuration
and characteristics of the disc or condition
of the recording.
Playing a disc
1 Load a disc.
➜ Playback starts automatically.
➜ The TV screen will display the number
of tracks for selection and current
playing status.
Selecting a folder and track/file
1 Press 34to select the folder and press
ENTER/OK to open the folder.
2 Press 34to select a track/file.
2 Playback will stop at the end of the disc.
3 To stop playback, press STOP 9.
3 Press ENTER/OK to confirm.
➜ Playback will start from the selected file
to the end of the folder.
Playing MP3/DivX/JPEG/Kodak
Picture CD
Special picture disc features
1 Load a Picture disc (Kodak Picture CD,
JPEG).
General Operation
1 Load a disc.
➜ For Kodak disc, the slide show will
➜ The disc reading time may exceed 30
seconds due to the complexity of the
directory/file configuration.
➜ The data disc menu appears on the TV
screen.
begin.
➜ For JPEG disc, the picture menu appears
on the TV screen.
2 Press PLAY Bto start the slide-show
playback.
2 Playback will start automatically. If not
press PLAY B.
Preview Function (JPEG)
00:00 00:00
001/020
This function shows the content of the
current folder or the whole disc.
Favorite
1 Press STOP 9during playback.
➜ 12 thumbnail pictures will appear on the
TV screen.
MP3
Piano
Cello
MP3
MP3
MP3
Jazz
Live
During playback, you can;
• Press S/ Tto select another
track/file in the current folder.
• Press PAUSE ;to pause playback.
2 Press S/ Tto display the other
pictures on the previous/next page.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Operations
3 Use 1234to highlight one of the picture
and press ENTER/OK to start playback
OR
Playing MP3 music and JPEG
picture simultaneously
1 Load a disc that contains music and
Move the cursor to highlight
on the
picture.
bottom of the page to start playback from
the first picture on the current page.
➜ The disc menu appears on the TV
screen.
4 Press MENU to return to Picture CD
menu.
2 Select an MP3 track.
3 During MP3 music playback, select a
picture from the TV screen and press
PLAY B.
Zoom picture
1 During playback, press ZOOM repeatedly
➜ The picture files will be played back one
after another until end of the folder.
to display the picture with different scales.
2 Use 1234to view the zoomed picture.
4 To quit simultaneous playback, press
MENU followed by STOP 9.
Playback with multi-angles
Helpful Hint:
• During playback, press 1234to
rotate the picture on the TV screen.
1: rotate the picture anti-clockwise
2: rotate the picture clockwise
3: flip the picture vertically
– Some files on Kodak or JPEG disc may be
distorted during playback due to the
configuration and characteristics of the disc.
4: flip the picture horizontally
Scan Effect
• Press ANGLE repeatedly to choose
different scan effect.
➜ Various of scan effect appears on the
top left hand corner on the TV screen.
TIPS: The operating features described here might not be possible for certain discs. Always refer to
the instructions supplied with the discs.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
The setup is carried out via the TV,
enabling you to customize the DVD Player
to suit your particular requirements.
Programming disc tracks and
discs
Program: Track (not for Picture
®
General Setup menu
CD/MP3/SA-CD/WMA/DivX )
You can play the contents of the disc in the
order you want by programming the tracks
to be played. Up to 20 tracks can be
stored.
1 Press SETUP.
2 Press 12to select ‘General Setup’ icon.
3 Press ENTER/OK to confirm.
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {PROGRAM}, then press 2to
select {FTS}.
GENERAL SETUP PAGE
DISC LOCK
2 Press ENTER/OK to confirm.
PROGRAM
OSD LANGUAGE
SCREEN SAVER
SLEEP
1
2
3
4
5
04
10
11
__
__
6
7
8
9
__
__
__
__
DIVX(R) VOD CODE
10 __
To input your favorite tracks/chapter
Locking/Unlocking the disc for
viewing
3 Use the numeric keypad (0-9) to enter
a valid track/chapter number.
maker. You can prevent a specific disc
from playing by locking the disc. Up to 40
discs can be locked.
next position.
➜ If the track number is more than ten,
press Tto open the next page and
proceed with programming or,
➜ Use 1234to highlight {NEXT} on the
program menu, then press ENTER/
OK.
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {DISC LOCK}, then press 2.
LOCK
Select this to block the playback of the
current disc. Subsequent access to a
locked disc requires six-digit password.
The default password is ‘000 000’ (see
page 28 “Changing the Password”).
5 Repeat steps 3–4 to input another track/
chapter number.
If you want to remove a track
6 Use 1234to move the cursor to the
UNLOCK
Select this to unlock the disc and allow
future playback.
track you want to remove.
7 Press ENTER/OK to remove this track
from the program menu.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
Note:
– On SA-CD discs, you can program tracks on
the CD layer.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Program: Disc
OSD Language
You can play the disc in the order you
want by programming the discs to be
played. Up to 5 discs can be stored.
This menu contains various language
options for display language on the screen.
For details, see page 9.
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {PROGRAM}, then press 2to
select {FDS}.
Screen Saver
This function is used to turn the screen
saver on or off.
2 Press ENTER/OK to confirm.
(1) Disc : _
(2) Disc : _
(3) Disc : _
(4) Disc : _
(5) Disc : _
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {SCREEN SAVER}, then press 2.
ON
Select this if you wish to turn off the TV
screen when disc playback is stopped or
paused for more than 15 minutes.
To input your favorite discs
OFF
3 Use the numeric keypad (0-9) to enter
Select this to disable the screen saver
function.
a valid disc number.
4 Use 1234to move the cursor to the
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
next position.
5 Repeat steps 3–4 to input another disc
number.
Sleep Timer
If you want to remove a disc
This feature automatically sets the DVD
player in standby mode after the amount of
time you have set.
6 Use 1234to move the cursor to the
disc you want to remove.
7 Use the numeric keypad (0-9), press 0
to remove this disc from the program
menu.
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {SLEEP}, then press 2.
2 Press 34to select a setting.
➜ You can select from 15, 30, 45 and 60
minutes. Select {OFF} to cancel the
sleep timer function.
To start program playback
• Use 1234to highlight {START} on
the program menu, then press ENTER/
OK.
3 Press ENTER/OK to confirm your
selection.
➜ Playback will start with the selected
tracks or discs under the programmed
sequence.
To exit program playback
• Use 1234to highlight {EXIT} on the
program menu, then press ENTER/
OK.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
®
DivX VOD registration code
Audio Setup Menu
®
Yamaha provide you with the DivX VOD
(Video On Demand) registration code that
allows you to rent and purchase videos
1 Press SETUP.
2 Press 12to select ‘Audio Setup’ icon.
3 Press ENTER/OK to confirm.
®
using the DivX VOD service.
For more information, visit at
AUDIO SETUP PAGE
1 In ‘GENERAL SETUP PAGE’, press 34to
highlight {DIVX(R) VOD CODE}, then
press 2.
ANALOG OUTPUT
DIGITAL AUDIO
SPEAKER SETUP
CD UPSAMPLING
NIGHT MODE
➜ The registration code will appear.
2 Press ENTER/OK to exit.
3 Use the registration code to purchase or
®
rent the videos from DivX VOD service
instructions and download the video onto
a CD-R for playback on this DVD player.
Setting the analog output
Helpful Hints:
– All the downloaded videos from DivX
Set Analog Output to match your DVD
Player’s playback capability.
®
VOD can only be played back on this DVD
player.
– Time search feature is not available during
DivX movie playback.
1 In ‘AUDIO SETUP PAGE’, press 34to
highlight {ANALOG OUTPUT}, then press
2.
STEREO
Select this to change channel output to
stereo which delivers sound from only the
two front speakers and subwoofer.
VIRTUAL SURROUND
Select this to reproduce the surround
channels virtually.
MULTI-CHANNEL
Select this setting when using a multi-
channel audio/(video) receiver with 6
channel inputs. In this mode, the player will
perform DTS decoding or Dolby Digital
5.1-channel decoding when applicable, and
Dolby Pro Logic decoding on DVD-Video
and Video-CD discs with 2-channel sound
tracks. No Dolby Pro Logic decoding is
done with (Super) Audio CD discs.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
96kHz
Setting the Digital output
Playback a disc recorded at the sampling
rate of 96kHz. If the 96kHz disc is copy
protected, the digital output will be muted
to comply with the standards.
The options included in Digital Audio are:
‘Digital Output’ and ‘LPCM Output’.
1 In ‘AUDIO SETUP PAGE’, press 34to
highlight {DIGITAL AUDIO}, then press 2.
2 Press the 34to highlight an option.
3 Enter its submenu by pressing 2.
Speaker Setup
This menu contains setup options for your
audio output which makes the speaker
setup system reproduce high quality
surround sound. For details, see page 10.
4 Move the cursor by pressing the 34to
highlight the selected item.
DIGITAL OUTPUT
Set the Digital output according to your
optional audio equipment connection.
CD Upsampling
This feature allows you to convert your
music CD to a higher sampling rate using
sophisticated digital signal processing for
better sound quality. If you have activated
the upsampling, the player will
OFF
Turn off the digital output.
ALL
If you have connected your DIGITAL
AUDIO OUT to a multi-channel decoder/
receiver.
automatically switch to stereo mode.
1 In ‘AUDIO SETUP PAGE’, press 34to
highlight {CD UPSAMPLING}, then press
2.
PCM ONLY
Only if your receiver is not capable of
decoding multi-channel audio.
OFF
Select this to disable CD-upsampling.
LPCM OUTPUT
88.2 kHz (X2)
Select this to convert the sampling rate of
the CDs twice higher than the original.
If you connect the DVD Player to a PCM
compatible receiver via the digital
terminals, such as coaxial or optical etc.,
you may need to adjust ‘LPCM Output’.
Discs are recorded at a certain sampling
rate. The higher the sampling rate, the
better the sound quality.
176.4 kHz (X4)
Select this to convert the sampling rate of
the CDs four times higher than the
original.
48kHz
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
Playback a disc recorded at the sampling
rate of 48kHz. 96kHz (if available on disc)
PCM data stream will be converted to
48kHz.
Note:
– This setting is only applicable for the signals
output from the analog jacks.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Night Mode
Setting the TV Display
In this mode, the high volume outputs are
softened and low volume outputs are
brought upward to an audible level. It is
useful for watching your favorite action
movie without disturbing others at night.
Set the aspect ratio of the DVD Player
according to the TV you have connected.
The format you select must be available on
the disc. If it is not, the setting for TV
display will not affect the picture during
playback.
1 In ‘AUDIO SETUP PAGE’, press 34to
highlight {NIGHT MODE}, then press 2.
1 In ‘VIDEO SETUP PAGE’, press 34to
highlight {TV DISPLAY}, then press 2.
ON
2 Press 34to highlight one of the options
Select this to level out the volume. This
feature is only available for movies with
Dolby Digital mode.
below:
4:3 PAN SCAN
OFF
Select this if you have
a normal TV and want
both sides of the
Select this when you want to enjoy the
surround sound with its full dynamic range.
picturetobetrimmed
or formatted to fit
your TV screen.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
4:3 LETTER BOX
Video Setup Menu
Select this if you have a
normal TV. In this case, a
wide picture with black
bands on the upper and
lower portions of the TV screen will be
displayed.
1 Press SETUP.
2 Press 12to select ‘Video Setup’ icon.
3 Press ENTER/OK to confirm.
16:9
VIDEO SETUP PAGE
Select this if you have
a widescreen TV.
TV TYPE
TV DISPLAY
PROGRESSIVE
PICTURE SETTING
BLACK LEVEL
CLOSED CAPTION
3 Select an item and press ENTER/OK.
TV Type
This menu contains the options for
selecting the color system that matches
the connected TV. For details, see page 8.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Progressive
Picture Setting
This feature is only applicable if you have
connected this DVD Player to a
Progressive Scan TV through the Y Pb Pr
jacks (see page 7).
This DVD Player provides three
predefined sets of picture color settings
and one personal setting which you can
define yourself.
1 In ‘VIDEO SETUP PAGE’, press 34to
highlight {PROGRESSIVE}, then press 2.
1 In ‘VIDEO SETUP PAGE’, press 34to
highlight {PICTURE SETTING}, then press
2.
ON
STANDARD
To enable Progressive Scan function.
Select this for standard picture setting.
OFF
BRIGHT
To disable Progressive Scan function.
Select this will make the TV picture
brighter.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
SOFT
Notes on activating Progressive:
– Ensure that your TV has progressive
scan.
Select this will make the TV picture softer.
PERSONAL
Select this to personalize your picture
color by adjusting the brightness, contrast,
tint and color (saturation).
– Connect with YPbPr video cable.
– If there is no picture, wait 15 seconds
for auto recover or deactivate
Progressive manually.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
1 Open the disc tray by pressing OPEN/
CLOSE /on the front panel.
3 If you select {PERSONAL}, then proceed
to steps 4–7.
2 Press 1.
➜ The ‘PERSONAL PICTURE SETUP’
menu appears.
3 Press ANGLE.
PERSONAL PICTURE SETUP
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE
USER SWITCH THE CONNECTION TO THE
“STANDARD DEFINITION” OUTPUT. IF THERE
ARE QUESTIONS REGARDING OUR VIDEO
MONITOR COMPATIBILITY WITH THIS
MODEL 525P AND 625P DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE
CENTER.
BRIGHTNESS
CONTRAST
TINT
0
0
0
0
COLOR
4 Press 34to highlight one of the following
options.
BRIGHTNESS
Increase the value will brighten the picture
or vice versa. Choose zero (0) for average
setting.
CONTRAST
This unit is compatible with the complete line of
YAMAHA products, including the projectors DPX-
1100, LPX-510 and the plasma monitor PDM-
4210.
Increase the value will sharpen the picture
or vice versa. Choose zero (0) to balance
the contrast.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
TINT
1 In ‘VIDEO SETUP PAGE’, press 34to
highlight {CLOSED CAPTION}, then press
2.
Increase the value will darken the picture
or vice versa. Choose zero (0) for average
setting.
ON
COLOR
To enable Closed Caption function.
Increase the value will enhance the color in
your picture or vice versa. Choose zero
(0) to balance the color.
OFF
To disable Closed Caption function.
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
5 Press 12to adjust the setting that best
suit your personal preference.
6 Repeat steps 4–5 for adjusting other color
features.
Preference Setup Menu
7 Press ENTER/OK to confirm.
1 Press STOP 9twice to stop playback (if
any), then press SETUP.
Selecting the black level (U.S.A.
model only)
2 Press 12to select the ‘Preference Setup’
icon.
If you set the TV type to NTSC, set Black
level shift to ON. This will improve the
color contrast during playback. The black
level setting has no effect if the TV type is
set to PAL.
3 Press ENTER/OK to confirm.
PREFERENCE PAGE
AUDIO
ON
SUBTITLE
DISC MENU
PARENTAL
PBC
Select this for enhanced black level.
OFF
MP3/JPEG NAV
PASSWORD
DEFAULT
Select this for standard black level.
Closed Caption (U.S.A. model
only)
Closed Captions are data that are hidden
in the video signal on specific discs,
invisible without a special decoder. The
difference between subtitles and captions
is that subtitles are intended for hearing
persons and captions are for the hearing
impaired. Subtitles rarely show all of the
audio. For example, captions show sound
effects (e.g., “phone ringing” and
Audio, Subtitle, Disc Menu
These menus contain various language
options for audio, subtitle and disc menu
which may be recorded on the DVD. For
details, see page 10.
“footsteps”), while subtitles don’t.
Before you select this function, please
ensure that the disc contains closed
captions information and your TV set also
has this function.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Restricting playback by Parental
Control
Some DVDs may have a parental level
assigned to the complete disc or to certain
scenes on the disc. This feature lets you set
a playback limitation level.
PBC (Playback Control)
You can set the PBC to ON or OFF. This
feature is available only on Video CD 2.0
with playback control (PBC) feature. For
details, see page 16.
The rating levels are from 1 to 8 and are
country dependent. You can prohibit the
playing of certain discs that are not suitable
for your children or have certain discs
played with alternative scenes.
MP3/JPEG Menu
MP3/JPEG Navigator can be set only if the
disc is recorded with menu. It allows you
to select different display menus for easy
navigation.
1 In ‘PREFERENCE PAGE’, press 34to
highlight {PARENTAL}, then press 2.
1 In ‘PREFERENCE PAGE’, press 34to
highlight {MP3/JPEG NAV}, then press 2.
WITHOUT MENU
Select this to display all the files contained
in the MP3/Picture CD.
PREFERENCE PAGE
AUDIO
1 KID SAFE
2 G
SUBTITLE
DISC MENU
PARENTAL
PBC
WITH MENU
3 PG
5 PGR
6 R
MP3/JPEG NAV
PASSWORD
DEFAULT
2 Press 34to select a setting, then press
ENTER/OK to confirm your selection.
7 NC 17
8 ADULT
2 Press 34to highlight a rating level for the
disc inserted and press ENTER/OK.
➜ To disable Parental controls and have all
Discs play, select {8 ADULT}.
3 Use the numeric keypad (0-9) to enter
the six-digit password (see page 28
“Changing the Password”).
➜ DVDs that are rated above the level you
selected will not play unless you enter
your six-digit password.
Helpful Hints:
– VCD, SVCD, CD, SA-CD have no level
indication, so parental control function has
no effect on these type of discs. This applies
to most illegal DVD discs.
– Some DVDs are not encoded with a rating
though the movie rating may be printed on
the Disc cover. The rating level feature does
not work for such Discs.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menu
Changing the Password
Restoring to original settings
The same password is used for both
Parental Control and Disc Lock. Enter
your six-digit password when prompted
on the screen. The default password is 000
000.
Setting the DEFAULT function will reset all
options and your personal settings to the
factory defaults, except your password for
Parental Control and Disc Lock.
1 In ‘PREFERENCE PAGE’, press 34to
highlight {DEFAULT}, then press 2to
select {RESET}.
1 In ‘PREFERENCE PAGE’, press 34to
highlight {PASSWORD}, then press 2to
select {CHANGE}.
2 Press ENTER/OK to confirm.
➜ All settings will now reset to factory
defaults.
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
PBC
MP3/JPEG NAV
PASSWORD
DEFAULT
CHANGE
2 Press ENTER/OK to enter the ‘Password
Change Page’.
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
OK
3 Use the numeric keypad (0-9) to enter
your old six-digit password.
➜ When doing this for the first time, key
in ‘000 000’.
➜ If you forget your old six-digit
password, key in ‘000 000’.
4 Enter the new six-digit password.
5 Enter the new six-digit password a second
time to confirm.
➜ The new six-digit password will now
take effect.
6 Press ENTER/OK to confirm.
TIPS: To return to the previous menu, press 1.
To remove the menu, press SETUP.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code
These pages can be used to select other languages.This does not affect the
options in “AUDIO”, “SUBTITLE” or “DISC MENU”.
Abkhazian
Afar
Afrikaans
Albanian
Amharic
6566
6565
6570
8381
6577
6582
7289
6583
6569
6589
6590
6665
6985
6669
6678
6672
6673
7866
6683
6682
6671
7789
6983
6765
6772
6769
7889
7889
9072
9065
6785
6785
6786
7587
6779
7282
6783
6865
7876
6890
6978
6979
6984
7079
7074
7073
7082
7089
7168
7176
7565
German
Gikuyu; Kikuyu
Greek,
Guarani
Gujarati
Hausa
Hebrew
Herero
Hindi
6869
7573
6976
7178
7185
7265
7269
7290
7273
7279
7285
7383
7379
7368
7365
7369
7385
7375
7165
7384
7465
7486
7576
7578
7583
7575
7577
7573
8287
7589
7586
7579
7574
7585
7574
7679
7665
7686
7666
7673
7673
7673
7678
7684
7666
7775
7771
7783
7776
7784
7186
Arabic
Armenian
Assamese
Avestan
Aymara
Azerbaijani
Bashkir
Basque
Belarusian
Bengali
Bihari
Bislama
Bokmål, Norwegian
Bosnian
Breton
Bulgarian
Burmese
Castilian, Spanish
Catalan
Chamorro
Chechen
Chewa; Chichewa; Nyanja
Chichewa; Chewa; Nyanja
Chinese
Chuang; Zhuang
Church Slavic; Slavonic;
Church Slavonic; Church
Chuvash
Cornish
Corsican
Croatian
Czech
Danish
Dutch
Dzongkha
English
Esperanto
Estonian
Faroese
Fijian
Finnish
French
Frisian
Gaelic; Scottish Gaelic
Gallegan
Hiri Motu
Hungarian
Icelandic
Ido
Indonesian
Interlingua (International)
Interlingue
Inuktitut
Inupiaq
Irish
Italian
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Khmer
Kikuyu; Gikuyu
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Kwanyama; Kuanyama
Lao
Latin
Latvian
Letzeburgesch;
Limburgan; Limburger;
Limburger; Limburgan;
Limburgish; Limburger;
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Malay
Malayalam
Maltese
Manx
Georgian
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code
These pages can be used to select other languages.This does not affect the options in
“AUDIO”, “SUBTITLE” or “DISC MENU”.
Maori
Marathi
7773
7782
7772
7779
7778
7865
7886
7886
7868
7882
7871
7869
8369
7868
7879
Sotho, Southem
South Ndebele
Spanish; Castilian
Sundanese
Swahili
8384
7882
6983
8385
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9065
9085
Marshallese
Moldavian
Mongolian
Nauru
Navaho, Navajo
Navajo; Navaho
Ndebele, North
Ndebele, South
Ndonga
Swati
Swedish
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Walloon
Welsh
Nepali
Northern Sami
North Ndebele
Norwegian
Norwegian Bokmål; Bokmål, 7866
Norwegian Nynorsk;
Nyanja; Chichewa; Chewa
Nynorsk, Norwegian;
Occitan (post 1500); Proven
7878
7889
7878
7967
Old Bulgarian; Old Slavonic; 6785
Old Church Slavonic; Old
Old Slavonic; Church
Oriya
6785
6785
7982
7977
7983
7983
8073
8065
7065
8076
8084
7967
8083
8185
8277
8279
8278
8285
8377
8371
8365
8367
7168
8382
8378
8368
8373
8375
8376
8379
Oromo
Ossetian; Ossetic
Ossetic; Ossetian
Pali
Panjabi
Persian
Polish
Wolof
Xhosa
Yiddish
Yoruba
Zhuang; Chuang
Zulu
Portuguese
Provençal; Occitan (post)
Pushto
Quechua
Raeto-Romance
Romanian
Rundi
Russian
Samoan
Sango
Sanskrit
Sardinian
Scottish Gaelic; Gaelic
Serbian
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Refer to the chart below when this unit does not function properly. If the
problem you are experiencing is not listed below or if the instruction below does
not help, set this unit to the standby mode, disconnect the power cord, and
contact the nearest authorized YAMAHA dealer or service center.
Problem
Solution
No power
No picture
– Check if the AC power cord is properly connected.
– Press the STANDBY/ON on the front of the DVD system
to turn on the power.
– Refer to your TV’s manual for correct Video In channel
selection. Change the TV channel until you see the DVD
screen.
– Check if the TV is switched on.
– If you did not use Progressive Scan connections (using the Y
PB PR jacks on the DVD Player) and you do not have a
picture at the TV, please follow the steps below to turn off
Progressive Scan;
1. Press /(OPEN/CLOSE) to open the disc tray.
2. Press 1.
3. Then press ANGLE to deactivate the Progressive. The
DVD Player will reset itself to Component/Interlaced
video.
Distorted picture
– Sometimes a small amount of picture distortion may appear
depending on the disc being played back. This is not a
malfunction.
Completely distorted picture
or black/white picture with
DVD
– Make sure the disc is compatible with the DVD Player.
– Ensure that the DVD Player’s TV Type is set to match that
of the Disc and your TV.
No sound or distorted sound
– Adjust the volume.
– Check that the speakers are connected correctly.
No audio at digital output
– Check the digital connections.
– Check if your receiver can decode MPEG-2 or DTS and if
not, please make sure the digital output is set to PCM
ONLY.
– Check if the audio format of the selected audio language
matches your receiver capabilities.
No output from subwoofer
during stereo
– Check that all speaker settings in the setup menu have been
changed to small instead of large.
Disc can’t be played
– The DVD+R/RW, DVD-R/RW, CD-R/RW must be
finalized.
– Ensure the disc label is facing up.
– Check if the disc is defective by trying another disc.
– If you have recorded a Picture CD or MP3 CD yourself,
ensure that your disc contains at least 10 pictures or 5 MP3
tracks.
– Region code incorrect.
Picture freezes momentarily
during playback
– Check the disc for fingerprints/scratches and clean with a
soft cloth wiping from centre to edge.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Solution
The player does not respond to
the Remote Control
– Aim the Remote Control directly at the sensor on the front
of the player.
– Reduce the distance to the player.
– Replace the batteries in the Remote Control.
– Re-insert the batteries with their polarities (+/– signs) as
indicated.
Buttons do not work
– To completely reset the player, unplug the AC cord from
the AC outlet for 5-10 seconds.
Player does not respond to
some operating commands
during playback.
– Operations may not be permitted by the disc. Refer to the
instructions of the disc jacket.
DVD Player cannot read CDs/
DVDs
– Use a commonly available cleaning CD/DVD to clean the
lens before sending the DVD Player for repair.
Menu items cannot be selected
– Press STOP twice before selecting Setup Menu.
– Depending on the disc availability, some menu items cannot
be selected.
Unable to play DivX movies
– Check that the DivX file is encoded in ‘Home Theater’
mode with DivX 5.x encoder.
No sound during DivX movies
playback
– The audio code may not be supported by the DVD player.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Analog: Sound that has not been turned into num-
bers.Analog sound varies, while digital sound has spe-
cific numerical values.These jacks send audio through
two channels, the left and right.
Multichannel DVD is specified to have each sound
track constitute one sound field. Multichannel refers to
a structure of sound tracks having three or more chan-
nels.
Aspect ratio: The ratio of vertical and horizontal
sizes of a displayed image.The horizontal vs. vertical
ratio of conventionalTVs.is 4:3,and that of widescreens
is 16:9.
Parental Control:A function of the DVD to limit
playback of the disc by the age of the users according to
the limitation level in each country.The limitation varies
from disc to disc; when it is activated, playback will be
prohibited if the software’s level is higher than the user-
set level.
AUDIO OUT Jacks: Jacks on the back of the DVD
System that send audio to another system (TV, Stereo,
etc.).
PCM (Pulse Code Modulation):A system for
converting analog sound signal to digital signal for later
processing, with no data compression used in conver-
sion.
Bit Rate:The amount of data used to hold a given
length of music; measured in kilobits per seconds, or
kbps. Or, the speed at which you record. Generally, the
higher the bit rate, or the higher the recording speed,
the better the sound quality. However, higher bit rates
use more space on a Disc.
Playback control (PBC): Refers to the signal
recorded on video CDs or SVCDs for controlling
reproduction. By using menu screens recorded on a
Video CD or SVCD that supports PBC, you can enjoy
interactive-type software as well as software having a
search function.
Chapter: Sections of a picture or a music piece on a
DVD that are smaller than titles.A title is composed of
several chapters. Each chapter is assigned a chapter
number enabling you to locate the chapter you want.
Progressive Scan: It displays all the horizontal lines
of a picture at one time, as a signal frame.This system
can convert the interlaced video from DVD into pro-
gressive format for connection to a progressive display.
It dramatically increases the vertical resolution.
ComponentVideo Out Jacks: Jacks on the back
of the DVD System that send high-quality video to aTV
that has ComponentVideo In jacks (R/G/B,Y/Pb/Pr,
etc.).
Region code:A system for allowing discs to be played
back only in the region designated beforehand.This unit
will only play discs that have compatible region codes.
You can find the region code of your unit by looking on
the product label. Some discs are compatible with more
than one region (or ALL regions).
Disc menu:A screen display prepared for allowing
selection of images, sounds, subtitles, multi-angles, etc.
recorded on a DVD.
Digital: Sound that has been converted into numerical
values. Digital sound is available when you use the DIGI-
TALAUDIO OUT COAXIAL or OPTICAL jacks.These
jacks send audio through multiple channels, instead of
just two channels as analog does.
S-Video: Produces a clear picture by sending separate
signals for the luminance and the color.You can use S-
Video only if yourTV has S- video In jack.
DivX 3.11/4x/5x:The DivX code is a patent pending,
MPEG-4 based video compression technology, devel-
oped by DivXNetworks, Inc., that can shrink digital
video to sizes small enough to be transported over the
internet, while maintaining high visual quality.
Super Audio CD (SA-CD):This audio format is
based upon the current CD standards but includes a
greater amount of information that provides higher
quality sound.There are three types of discs:single layer,
double layer and hybrid discs.The hybrid disc contains
both standard audio CD and Super Audio CD informa-
tion.
Dolby Digital:A surround sound system developed
by Dolby Laboratories containing up to six channels of
digital audio (front left and right, surround left and right,
center and subwoofer).
Surround:A system for creating realistic three dimen-
sional sound fields full of realism by arranging multiple
speakers around the listener.
DTS: DigitalTheatre Systems.This is a surround sound
system, but it is different from Dolby Digital.The for-
mats were developed by different companies.
Title:The longest section of a picture or music feature
on DVD, music, etc., in video software, or the entire
album in audio software. Each title is assigned a title
number enabling you to locate the title you want.
JPEG:A very common digital still picture format.A
still-picture data compression system proposed by the
Joint Photographic Expert Group, which features small
decrease in image quality in spite of its high compres-
sion ratio.
VIDEO OUT jack: Jack on the back of the DVD Sys-
tem that sends video to aTV.
MP3:A file format with a sound data compression sys-
tem.“MP3” is the abbreviation of Motion Picture
Experts Group 1 (or MPEG-1) Audio Layer 3. By using
MP3 format, one CD-R or CD-RW can contain about
10 times as much data volume as a regular CD can.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
PLAYBACK SYSTEM
AUDIO PERFORMANCE
DVD-Video
DA Converter
Signal-Noise (1 kHz)
Dynamic range (1 kHz)
DVD
24bit, 192kHz
SA-CD multichannel and SA-CD stereo
Video CD & SVCD
CD
105dB
95dB
fs 96 kHz
2Hz- 44kHz
2Hz- 22kHz
2Hz- 22kHz
2Hz- 20kHz
2Hz- 20kHz
0.0035%
PICTURE CD
fs 48 kHz
fs 48 kHz
fs 44.1kHz
fs 44.1kHz
CD-R, CD-RW
SVCD
DVD+R, DVD+RW
DVD-R, DVD-RW
CD/VCD
Distortion and Noise (1 kHz)
VIDEO PERFORMANCE
TV STANDARD (PAL/50Hz) (NTSC/60Hz)
Video (CVBS) Output
S-Video output
1 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
C: 0.3 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
Pb/Cb Pr/Cr: 0.7 Vpp into
75 ohm
Number of lines
Playback
625
525
Multistandard
(PAL/NTSC)
Component video output
CONNECTIONS
Y Output
Cinch (green)
Cinch (blue)
Cinch (red)
Mini DIN, 4 pins
Cinch
Black Level Shift
On/Off
Pb/Cb Output
Pr/Cr Output
S-Video Output
Video Output
AUDIO FORMAT
Digital Mpeg/ Dolby Digital/ Compressed Digital
DTS
Audio Output (L+R) Cinch
Digital Output 1 coaxial, 1 optical
IEC60958 for CDDA / LPCM
PCM
16, 20, 24 bits
fs, 44.1, 48, 96 kHz
24, 32, 56, 64, 96, 128,
256 kbps
MP3(ISO 9660)
IEC61937 for MPEG 1/2, Dolby
Digital and DTS
fs, 16, 22.05, 24, 32,
44.1, 48 kHz
6 channel analog output
Audio Front L/R
Cinch (white/red)
WMA
32–192 kbps, mono, stereo
Audio Surround L/R Cinch (white/red)
Full decoding of Dolby Digital and DTS multi-channel sound
Analog Sound Stereo
Audio Center
Cinch (blue)
Cinch (black)
Audio Subwoofer
Dolby Surround compatible downmix from Dolby Digital
multi-channel sound
CABINET
Dolby Pro Logic II
Dimensions (w x d x h)
Weight
435 x 425 x 75 mm
Approx. 5.5 Kg
3D sound for virtual 5.1 channel sound on 2 speakers
POWER SUPPLY
Power inlet
U.S.A model
Australia model
120V, 60Hz
240V, 50Hz
Approx. 15W
< 1W
Power usage
Power usage standby
Specifications subject to change without prior
notice
34
Download from Www.Somanuals.com. All Manuals Search And Download.
©2004
All rights reserved.
3139 246 13703
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in China IP
Download from Www.Somanuals.com. All Manuals Search And Download.
|