DESCRIPTION
The Micro Link IR Receiver is a small peep-hole style infrared repeater
assembly. The Micro Link IR Receiver is equipped with a 7-foot cable and
a 3.5mm stereo mini plug, which is plugged directly into the “IR RCVR”
jack on the connecting block, such as the models 789-44, CB60, and 791-
44. The Micro Link IR Receiver is primarily intended for use in installations
where the connecting block is within reach of its 7-foot cable – as when
installing the Micro Link IR Receiver in a cabinet where the controlled
equipment is behind closed doors.
FEATURES
INSTALLATION INSTRUCTIONS
•
•
Small size; mounts in 1/2” diameter hole. 2 inches deep (50mm).
Quick-Connect 3.5mm Stereo Mini Plug on 7ft. cable for direct plug-in
to Xantech Connecting Blocks.
MODEL
•
•
Works in normal 3-wire mode (12VDC, IR, GND).
Green Talkback LED for System Verification.
ML85
SPECIFICATIONS
Micro Link™ Peep-Hole Style
Plasma\LCD\LED\CFL Friendly
IR Receiver
•
•
Infrared modulation frequency bandwidth: 30 – 60 kHz.
IR reception range: Up to 80 feet, depending on remote control output
strength and ambient conditions.
•
•
Reception angle: 55 degrees off axis for 50% range reduction.
Cable requirements: 3-conductor. Use 24 gauge up to 200’, 22 gauge
up to 600’ 20 gauge up to 2000’, 18 gauge up to 5000’ – unshielded
OK.
•
•
•
Max. transmission length: 1 mile using 18 gauge wire.
Maximum current output: 100mA
Drives IR emitters through Xantech Connecting Blocks, Controllers,
etc.
•
•
Dimensions: 1/2” diameter x 2” deep (13mm x 50mm).
Power requirements: +12VDC, 20mA.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
LARGE SYSTEM APPLICATION
TROUBLE SHOOTING:
The ML85 IR receiver is compatible with all Xantech Connecting Blocks.
Different connecting blocks are provided for application specific situations.
For instance, in the diagram below, a 791-44 connecting block is used to
control several components.
1. Perhaps the most common problem you may encounter is stray IR
(infrared) or RF (radio frequency) interference preventing proper
operation of the controlled equipment.
•
Fluorescent, Compact Fluorescent, Neon or Halogen
lights, Neon Art, and light dimmers.
Direct of reflected sunlight.
Infrared security sensors (active types).
RF radiation from TV sets that may be close to the Micro
Link IR Receiver.
•
•
•
791-44
ML Series
Amplified
Satellite Receiver
IR Receivers
Connecting Block
Emitter
2. You can confirm the source of the interference by temporarily
turning off TV sets, isolating the Micro Link IR Receiver from all
sunlight and turning off all lights, light dimmers and Infrared
security systems. Then check to see if the Micro Link IR Receiver
operates the component.
VCR
Emitter
AVReceiver
IR Photodiode
Talkback LED
+12 VDC
GN D
•
•
•
Sometimes interference will cause the red Talk-Back LED
on the front of the Micro Link IR Receiver to blink dimly,
intermittently, or continuously.
The Talk-Back Led should only blink when you are
sending infrared commands to the Micro Link IR receiver
from a remote control.
STATUS
IR IN
Emitter
CD Changer
781ERGPS
Hand Held
Remote
Emitter
To 120 VAC
(unswitched)
Cassette Deck
It may be necessary to move either the interfering source
of the Micro Link IR Receiver to achieve proper operation.
Controlled Equipment
(mounted behind
closed cabinet doors)
Emitter
3. If the Talk-Back LED or the 286D Emitters do not blink when you
are sending IR commands to the Micro Link IR Receiver from a
remote control, check the following:
•
Make sure the power supply is plugged securely into a live
AC electrical outlet.
•
Be sure the stereo mini plug of the Micro Link IR Receiver
is plugged into the “IR RCVR” jack on the CB12
Connecting Block, not into the “OUT” jack.
•
Check to see that all the mini plugs are properly seated
into the mini jacks on the CB12 Connecting Block.
4. If the 283D Emitters blink, but the component does not respond,
reposition the 283D Emitter(s). They may not be located directly
over the component’s infrared receiving “window”. Consul the
owner’s manual of the unit or the manufacturer for the exact
location of the infrared “window”.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
Xantech® warrants its products to be free of defects in materials or workmanship. This is a
Limited Lifetime warranty from the date of purchase by the original consumer. Any products
returned to Xantech and found to be defective by Xantech within the warranty period will be
repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the
actual cost of installation or removal of the product, nor for any incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation may not apply to you. This warranty gives you specific legal
rights. You may have additional legal rights that vary from state to state.
Xantech Corporation
13100 Telfair Ave. 2F, Sylmar CA 91342 | Xantech.com
Installation Instructions, ML85 © 2009 Xantech Corporation
Document # 08905266B
This document is copyright protected. No part of this manual may be copied or reproduced in
any form without prior written consent from Xantech Corporation. Xantech Corporation shall
not be liable for operational, technical, or editorial errors/omissions made in this document.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|