MODEL
283DPRO
Professional Visible Emitter
INSTALLATION INSTRUCTIONS
BLACK (IR OPAQUE) EMITTER SHIELD
•
An optional shield, available from Xantech as model 28DES, fits over
the emitter head and the sensor window of the controlled component.
It prevents unwanted external IR signals from passing through or
leaking past it.
DESCRIPTION
The 283DPRO Professional Visible Emitter is a two-piece Emitter.
Featuring a Designer Emitter, the head-end piece can be attached to any
electronic component, such as a DVD player. With dressed cables, using
the included adhesive cable channels, an Emitter can now become part of
the electronic equipment. The secondary section connects the Designer
Emitter to a Xantech IR system. Additional lengths for the secondary
section are available in the 283DPROKIT. The 283DPRO eliminates
cabling confusion and turns the most complex installation into a
professional installation.
•
Use the 28DES when you want the equipment to respond only to the
283DPRO, such as in zone controlled systems.
CONNECTING THE EMITTERS
•
•
•
Simply insert the mono mini plug of the 283DPRO emitter into the
“EMITTERS” or “OUT” jacks on any of the Xantech Connecting
Blocks or Controllers.
CAUTION: DO NOT plug emitters into the IN/OUT or HIGH OUT
jacks on the 790-00 and 791-44 Connecting Blocks. To do so will
destroy the emitters!
The 283DPRO visible emitter will also indicate the presence of stray
IR or RF interference by randomly blinking when no IR control signal
is being sent. Reposition the IR receiver of the interfering source to
eliminate or reduce the random blinking. The more the random
blinking is reduced, the better the system will function.
INSTALLATION
HEAD-END DESIGNER EMITTER
SECONDARY CABLE (LENGTH 6 FEET)
ATTACHING THE EMITTERS TO IR SENSOR WINDOWS
•
Each emitter has a clear adhesive layer on the bottom flat surface of
the shell.
•
Simply peel off the adhesive cover and affix the emitter to the center
of the IR sensor window on the controlled component’s front panel.
Limited Warranty
Xantech® warrants its products to be free of defects in materials or
workmanship. This is a Limited Lifetime warranty from the date of purchase
by the original consumer. Any products returned to Xantech and found to
be defective by Xantech within the warranty period will be repaired or
replaced, at Xantech’s option, at no charge. Xantech will not be
responsible for the actual cost of installation or removal of the product, nor
for any incidental or consequential damages. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the
above limitation may not apply to you. This warranty gives you specific
legal rights. You may have additional legal rights that vary from state to
state.
•
•
•
In some cases it may be difficult to find the location of the IR sensor
on the component. Consult the owner’s manual of the unit, or the
manufacturer, for the exact IR sensor window location.
Double-sided adhesive tape is included. If you move the emitter to a
different component, use this tape to replace the current adhesive
layer for the best adhesion.
The shell, though dark in appearance, is transparent to infrared light,
allowing commands from a handheld remote control to pass through
it. This permits direct control of the equipment from a handheld
remote as well as from the 283DPRO.
Xantech Corporation
13100 Telfair Ave. 2F, Sylmar CA 91342 | Xantech.com
Installation Instructions, 283DPRO © 2008 Xantech Corporation
Document # 08905199X1
This document is copyright protected. No part of this manual may be
copied or reproduced in any form without prior written consent from
Xantech Corporation. Xantech Corporation shall not be liable for
operational, technical, or editorial errors/omissions made in this document.
Download from Www.Somanuals.com. All Manuals Search And Download.
|