Woodstock Nail Gun W1775 User Manual

MODEL W1775

NAILER/STAPLER KIT

OWNER'S MANUAL

Phone: (360) 734-3482 • Online Technical Support: [email protected]

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#9568BL Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous

conditions. This manual uses a series of symbols and signal words which are intended

to convey the level of importance of the safety messages. The progression of

symbols is described below. Remember that safety messages by themselves do not

eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if

not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury.

It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful

information about proper operation of the

equipment.

NOTICE

Safety Instructions for Pneumatic Tools

5. KEEP CHILDREN AND VISITORS

AWAY. All children and visitors

should be kept at a safe distance

from work area.

1. KEEP ALL SAFETY DEVICES IN

PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking

to see that keys and adjusting

wrenches are removed from tool

before operation.

6. MAKE WORKSHOP CHILD PROOF by

locking your shop and shutting off

air valves.

7. DO NOT FORCE TOOL. It will do

the job better and safer at the rate

for which it was designed.

3. KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.

4. DO NOT USE IN DANGEROUS

ENVIRONMENT. Do not use

8. USE THE RIGHT TOOL. Do not

force tool or attachment to do a

job for which it was not designed.

pneumatic tools in damp or wet

locations, or where any flammable

or noxious fumes may exist. Keep

work area well lighted.

9. DO NOT USE UNDER THE

INFLUENCE OF DRUGS OR

ALCOHOL.

-1-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

Safety Instructions for Pneumatic Tools

17. DISCONNECT TOOLS before

servicing, changing accessories, or

moving to another location.

10. USE PROPER AIR HOSE for the

tool. Make sure your air hose is in

good condition and is long enough

to reach your work without

stretching.

18. DO NOT OVERREACH. Keep proper

footing/balance at all times.

11. WEAR PROPER APPAREL. Do

not wear loose clothing, gloves,

neckties, rings, bracelets, or

other jewelry which may get

caught in moving parts. Non-slip

footwear is recommended. Wear a

protective hair covering to contain

long hair.

19. USE THE RECOMMENDED

ACCESSORIES. Consult owner’s

manual for recommended

accessories. The use of improper

accessories may cause risk of

injury.

20. CHECK FOR DAMAGED PARTS

BEFORE USING. Check for binding

and alignment of parts, broken

parts, part mounting, loose bolts,

and any other conditions that

mayaffect machine operation.

Repair or replace damaged parts.

12. ALWAYS USE SAFETY GLASSES.

Also use a face or dust mask

if cutting operation is dusty.

Everyday eyeglasses only have

impact resistant lenses, they are

NOT safety glasses.

21. NEVER LEAVE UNATTENDED TOOL

CONNECTED TO AIR. Disconnect

the air hose and do not leave tool

until it is relieved of any built up

pressure.

13. WEAR APPROVED HEARING

PROTECTION. Air escaping from

pneumatic tools can exceed safe

exposure limits and may cause

hearing damage with prolonged

exposure.

22. NEVER ALLOW UNTRAINED

USERS TO USE THIS TOOL WHILE

UNSUPERVISED.

14. SECURE WORK. Use clamps or a

vise to hold work when practical.

It is safer than using your hand

and frees both hands to operate

tool.

23. IF YOU ARE UNSURE OF THE

INTENDED OPERATION, STOP

USING TOOL. Seek formal training

or research books or magazines

that specialize in pneumatic tools.

15. MAINTAIN TOOLS WITH CARE.

Keep tools lubricated and clean

for best and safest performance.

Follow instructions for lubricating

and changing accessories.

24. BE AWARE OF HOSE LOCATION

WHEN USING PNEUMATIC TOOLS.

Hoses can easily become a tripping

hazard when laid across the floor

or spread out in a disorganized

fashion.

16. REDUCE THE RISK OF

UNINTENTIONAL FIRING. Do not

carry tool with hand on trigger

and always disconnect from air

when not in use.

-2-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

Additional Safety for Nailers/Staplers

1. HAND INJURIES: Do not place your

hands near the nail/staple point

of entry. A nail/staple can deflect

and tear through the surface of the

workpiece, puncturing your hand or

fingers.

5. HOSE USAGE: Make sure your air

hose is designed for the tool in

use, is in good condition, and is

long enough to reach your work

without stretching. However, an

overly long air hose in the work

area may be a tripping hazard.

2. COMBUSTIBLE GASES: Never

connect the nailer/stapler to

pressurized oxygen or other

combustible gases as a power

source. Only use filtered,

lubricated, and regulated

compressed air.

6. OPERATING QUESTIONS: If you

are not sure about the intended

operation, stop using the nailer/

stapler. Seek formal training.

7. MAINTENANCE: Always disconnect

air from the nailer/stapler when

servicing or installing nails.

During maintenance, a nailer/

stapler connected to air may

fire accidentally, causing serious

personal injury.

3. SAFE HANDLING: Never point the

nail/stapler at others! Do not keep

the trigger pulled when loading

fasteners, carrying, or holding tool.

Carry the nailer/stapler only by the

handle, never by any other part.

Do not carry the nailer/stapler by

the air hose. Disconnect the nailer/

stapler from the air hose when

going up and down ladders.

8. COMPRESSED AIR RATING: Do

not connect the nailer/stapler to

compressed air that exceeds 120

PSI.

9. CHECK VALVE: Do not use a check

valve or any other fitting that

4. CLEANING: Never use gasoline or

other flammable liquids to clean

the nailer/stapler; vapors in the

nailer/stapler will ignite by a spark

and cause it to explode.

allows air to remain in the tool.

10. MODIFICATION: Do not modify

this tool or bypass the safety nose

mechanism.

Never point this nailer/stapler at

yourself or another person! Always

pay attention to the direction this

nailer/stapler is pointed. Use this

tool with respect and caution to

lessen the possibility of operator

or bystander injury. Ignoring this

warning may result in serious

personal injury.

Nailer/stapler accidents routinely

happen while moving the gun to

another location, such as up ladders,

to another room, or even another

job site. Always disconnect the gun

immediately after use and never

transport the gun while connected to

the air—even if the air compressor is

disconnected from its power source!

-3-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

INTRODUCTION

Woodstock Technical

Tool Data

Support

Brad Length...............⁵⁄8"-2" (18 Gauge)

Staple Length........................ ⁵/8"-1⁵⁄8

This tool has been specially designed

to provide many years of trouble-free

service. Close attention to detail,

ruggedly built parts and a rigid quality

control program assure safe and reliable

operation.

Staple Crown ................ ¹⁄4" (18 Gauge)

Magazine Capacity................100 pieces

Air Inlet.................................¼" NPT

Weight................................. 3.3 lbs.

Operating Pressure ...............60-100 PSI

Woodstock International, Inc. is

committed to customer satisfaction.

Our intent with this manual is to include

the basic information for safety, setup,

operation, maintenance, and service of

this product.

We stand behind our tools! In the

event that questions arise about

your tool, please contact Woodstock

International Technical Support at

(360) 734-3482 or send e-mail to:

[email protected]. Our

knowledgeable staff will help you

troubleshoot problems and process

warranty claims.

Read the manual before operation.

Become familiar with this nailer/

stapler, its safety instructions,

and its operation before beginning

any work. Serious personal injury

may result if safety or operational

information is not understood or

followed.

If you need the latest edition of this

manual, you can download it from

http://www.shopfox.biz.

If you have comments about this

manual, please contact us at:

Woodstock International, Inc.

Attn: Technical Documentation

Manager

P.O. Box 2309

Bellingham, WA 98227

Email: [email protected]

No list of safety guidelines can be

complete. Every shop environment

is different. Always consider safety

first, as it applies to your individual

working conditions. Use this and

other tools with caution and respect.

Failure to do so could result in serious

personal injury, damage to equipment

or poor work results.

-4-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

Compressed Air System

The Model W1775 is designed to be

operated at 60-100 PSI using clean,

dry, regulated, compressed air. Do not

exceed the 120 PSI maximum operating

pressure for your model.

Before using your new nailer/stapler,

regulate the air pressure to find the

optimum setting within the specified

operating range. Start by testing the

nailer/stapler at a low setting, then

increase the air pressure as needed for

satisfactory results.

Exceeding the maximum permissible

operating pressure may damage

the nailer/stapler and cause it to

malfunction. To protect yourself

from personal injury, DO NOT

allow the air pressure to exceed

the recommended pressure for this

nailer/stapler!

An in-line filter/lubricator/regulator unit

can be installed as depicted in Figure 1.

This filter/lubricator/regulator unit

will protect your tool from damaging

water build-up, allow you to adjust and

maintain regulated air pressure to your

tool, and save you the inconvenience of

having to manually lubricate your tool

every time you use it.

If you plan on installing a filter/

lubricator/regulator unit in your

compressed air system, always follow the

connection instructions that come with

the unit.

��

Figure 1. Typical filter/lubricator/regulator installation order.

-5-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

SETUP

Unpacking

This tool has been carefully packaged for safe transportation. If you notice the tool

has been damaged during shipping, please contact your authorized Shop Fox dealer

immediately.

Inventory

The following is a description of the main components shipped with the Model W1775.

Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the tool

or examine the packaging materials carefully. Occasionally we pre-install certain

components for safer shipping.

Box Inventory (Figure 2)

Qty

D. Safety Goggles........................... 1

E. Hex Wrench 3mm ....................... 1

F. Hex Wrench 4mm ....................... 1

A. 2-in-1 Nailer/Stapler ................... 1

B. Pneumatic Tool Oil ..................... 1

C. Carrying Case............................ 1

Figure 2. Model W1775 inventory.

-6-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

— If the nailer/stapler fires when

the trigger is pulled, without the

safety nose mechanism being

depressed, then the nailer/stapler

is not working properly.

Safety Nose Mechanism

A safety mechanism on the nose of the

nailer/stapler protects against accidental

firing. When the trigger is pressed, the

nailer/stapler will not fire until the safety

nose mechanism is depressed.

— If you find that the safety nose

mechanism is not working prop-

erly, check the lubrication of its

sliding components.

Before you use your nailer/stapler for

the first time, check the safety nose

mechanism to ensure proper function.

To check the safety nose mechanism,

do these steps:

Do not attempt to modify or bypass

the safety nose mechanism to make

the nailer/stapler fire without pushing

the nose down.

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

2. Make sure the magazine is empty and

contains no nails/staples.

3. Make sure the trigger and the safety

nose mechanism move up and down

without sticking.

The safety mechanism is a mechanical

device that can fail. Never rely on

this mechanism as an excuse to point

the nailer/stapler at yourself or

any bystanders. Serious injury may

occur.

4. Connect the nailer/stapler to the air

supply.

5. Without pressing the trigger,

depress the safety nose mechanism

against a scrap piece of wood that is

clean and free of any knots, nails, or

other foreign objects.

— If the nailer/stapler does not fire,

then the safety nose mechanism is

working correctly.

Operating this nailer/stapler can

propel objects into the air, causing

immediate eye damage. To protect

yourself, always wear ANSI approved

safety glasses or goggles when

operating this equipment.

— If the nailer/stapler does fire

when you do this, immediately

disconnect the nailer/stapler from

the air supply and call Technical

Support.

-7-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

OPERATIONS

When replacing brad nails in your Model

W1775, follow these guidelines:

Pusher

Gauge: 18

Brad Length: ⁵⁄8"-2"

Staple Length: ⁵⁄8"-1⁵⁄8" (crown ¹⁄4")

Capacity: 100

Magazine

Sight Window

To load your nailer/stapler, do these

steps:

Figure 4. Loading nails into magazine.

4. Slide the staples or brads all the way

down to the nose of the nailer/sta-

pler.

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

5. Push the magazine toward the nose of

the nailer/stapler until the catch lever

locks.

2. Grip the nailer/stapler firmly,

unlatch the catch lever (Figure 3),

and pull the magazine pusher back

completely.

6. Reload the nailer/stapler when the

magazine sight window (Figure 4)

shows the nail or staple level is low.

The sight window shows up to approxi-

mately 50 nails or staples loaded.

Operating

If you have not read the safety

instructions in this manual, do not

operate the nailer/stapler.

Figure 3. Catch lever engaged and

magazine pusher retracted.

Before you operate your nailer/stapler,

place two to three drops of the included

oil into the quick connect fitting where

the nailer/stapler connects to the air

supply, unless using a lubricator unit.

3. Insert a strip of brads or staples,

pointed-end down, into the magazine

as shown in Figure 4.

To operate your nailer/stapler, do these

steps:

1. Connect the air supply to the quick

connect fitting.

-8-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

2. To test for proper nail penetration,

hold the nailer/stapler perpendicular

to the surface of a piece of clean

scrap wood that is thick enough for

the length of nails/staples you have

loaded.

— If the nail/staple either went too

far or not far enough, then go to

the Adjusting Depth section on

this page.

Adjusting Depth

A depth adjustment knob is attached

to the nose for setting the nail/staple

depth.

3. Depress the safety nose mechanism

against your workpiece.

4. Before pulling the trigger, make sure

your free hand and other body parts

are positioned out of the way of a

potential path of a nail/staple in case

of deflection.

To adjust the depth, do these steps:

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

Deflection is caused when grain

2. Rotate the adjustment knob (Figure

6) clockwise to increase depth or

irregularities, knots or foreign objects

inside the wood cause the nail/staple

to change its path, resulting in the

nail/staple puncturing the surface of

the workpiece, as shown in Figure 5.

counterclockwise to decrease depth.

Adjustment Knob

Besides damaging your workpiece,

deflection can cause injury if your

free hand is securing the workpiece

in the location that the nail/staple

deflects.

Figure 6. Loosening cap screw for depth

adjustment.

3. Connect nailer/stapler to the air

supply and test the nail depth.

Repeat this entire procedure if

necessary until the nail/staple depth

is satisfactory.

Figure 5. Example of nail deflection.

5. Pull the trigger.

DO NOT place your hands near the

staple point of entry. A nail/staple

can deflect and tear through the

surface of the workpiece, puncturing

your hand or fingers.

— If the nail/staple drove into the

wood far enough, continue with

your intended operations.

-9-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

To clear a jammed nail from the dis-

charge area, do these steps:

Clearing Jammed Nails

A jammed nail or staple must be cleared

before using the nailer/stapler again.

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

To clear a jammed nail or staple from

the magazine, do these steps:

2. Unlock the catch lever and pull the

magazine pusher back completely.

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

3. Remove the nail/staple stick from the

magazine.

2. Unlock the catch lever and pull the

magazine pusher back completely.

4. Loosen the cap screws shown in

Figure 7, and remove the cover with

a 3mm hex wrench. Dislodge the

jammed nail/staple with a pair of

needle nose pliers.

3. Locate and remove the jammed

nail/staple with a pair of needle nose

pliers.

4. Throw the damaged nail/staple away.

Cap Screws

5. Inspect the nail/staple stick. If it is

bent or damaged, throw it away and

insert a new stick that only contains

clean, undamaged nails/staples. DO

NOT use dirty or damaged nails/

staples!

Cover

6. Push the magazine pusher forward to

the front of the magazine until the

catch lever locks.

Figure 7. Opening cover to clear a jam.

5. Secure the cover with the cap screws

removed in Step 4.

6. Throw the damaged nail/staple away.

7. Inspect the nail/staple stick. If it is

bent or damaged, throw it away and

insert a new stick that only contains

clean, undamaged nails/staples. DO

NOT use dirty or damaged nails/

staples!

8. Slide the magazine pusher forward to

the front of the magazine until the

catch lever locks.

-10-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

6. Open the nose cover as if to clear a

Replacing Piston and

O-Rings

Under heavy use, a piston or piston shaft

may wear out. Replacement is quick and

easy. Contact your authorized Shop Fox

dealer to obtain the Piston Repair Kit

(part number X1775001).

jammed nail/staple.

7. Watch the discharge area and push

the top of the piston with your

finger. You will see the piston shaft

slide down the discharge area.

8. Taking care not to scratch or dent

the nailer parts, use a wooden

dowel or similarly shaped tool to

push the piston shaft back inside the

nailer/stapler until you can grip the

piston head and remove it from the

cylinder. Clean and inspect the parts

for cracks, wear, or burrs.

9. Place a new O-ring on the new piston

and apply a thin film of the nailer/

stapler lubricating oil on the O-ring.

Always disconnect air from nailer/

stapler whenever servicing! During

maintenance, a nailer/stapler con-

nected to air may fire accidentally,

causing serious personal injury!

10. Insert the new piston in the cylinder.

Make sure that the grooves on the

piston shaft line up with those on the

guide at the bottom of the cylinder.

The new piston should easily slide

into the cylinder. DO NOT force the

piston into the cylinder! If the piston

is not easily inserted, double-check

the alignment of the piston shaft with

the grooves on the guide.

To replace a piston and O-rings, do

these steps:

1. DISCONNECT NAILER/STAPLER FROM

THE AIR SUPPLY!

2. Remove all nails/staples from the

magazine cartridge, and clean the

exterior of the nailer.

11. After the piston is inserted correctly,

close the magazine. Replace the rear

cap assembly and tighten the four

cap screws.

3. Remove the four cap screws on the

back of the nailer/stapler, near the

exhaust port.

12. For more assistance, or to install a

complete O-ring set, refer to the

appropriate breakdown diagram

in the back of this manual for

component locations.

4. Remove the cap.

5. The top of the piston should now be

visible inside the cylinder, which is

housed in the head of the nailer/sta-

pler.

-11-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

CLEANING & LUBRICATION

Cleaning

Lubricating

Disconnect the nailer/stapler from the

air supply before cleaning. Use a good

solvent to clean the nose assembly of the

nailer/stapler. Always be sure that the

nailer/stapler is dry before using it again.

Standard pneumatic tool oil has been

included with your new Shop Fox nailer/

stapler to help maintain its useful life.

Place two to three drops of oil in the

nailer/stapler air inlet (as shown in

Figure 8) before every use, or after 2

hours of continuous use.

Do not allow dust, chips, sand, etc. into

the air connectors or into the body of the

nailer/stapler; this may result in leaks

and damage to the nailer/stapler and the

air couplings.

Figure 8. Lubricating nailer/stapler via

air inlet.

Wipe off any excess oil near the nailer/

stapler exhaust to avoid dust build-up.

When the oil that was included with the

nailer/stapler has been completely used,

replace with a quality pneumatic tool oil.

An alternative to manual oiling is to

install a lubricator in your air compressor

line. A lubricator eliminates the need to

oil your tool each time you use it. If you

have a lubricator in your air compressor

line, ensure it is functioning properly.

Never use gasoline or other

flammable liquids to clean this

tool. Vapors in the tool may ignite,

causing the tool to explode. Ignoring

this warning may lead to serious

personal injury or even death!

-12-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

PARTS BREAKDOWN

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

-13-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

PARTS LIST

REF PART�# DESCRIPTION

X1775044 RETAINER�SNAP

X1775001 PISTON�REPAIR�KIT

X1775002 CARRYING�CASE

X1775045 STAND�PLATE

XPEC12M E-CLIP�12MM

XPAW04M HEX�WRENCH�4MM

XPAW03M HEX�WRENCH�3MM

XPLW02M LOCK�WASHER�4MM

X1775006 AIR�PLUG�COVER

X1775007 1/4"�NPT�MALE�CONNECT

X1775008 END�CAP

X1775009 O-RING�36.3�X�3.55

X1775010 RUBBER�HANDLE�CASE

XPSB16M CAP�SCREW�M4-.7�X�16

X1775047 COMRESSION�SPRING

X1775048 STAND

XPRP12M ROLL�PIN�2.5�X�18

X1775050 SAFETY�PLATE

X1775051 O-RING�2.96�X�1.7

X1775052 TRIGGER

X1775053 PIN�2.97�X�30

X1775054 O-RING�11.2�X�1.85

X1775055 TRIGGER�VALVE�GUIDE

X1775056 O-RING�1.9�X�1.1

X1775057 O-RING�8�X�1

XPN04M

HEX�NUT�M4-.7

XPSB18M CAP�SCREW�M4-.7�X�8

X1775014 FIXED�SEAT

X1775015 MAGAZINE

X1775016 INLAY�SLICE

X1775017 PIN�1.5�X�12

X1775018 DRIVER�GUIDE

X1775019 NOSE�COVER

XPSB17M CAP�SCREW�M4-.7�X�10

XPSB41M CAP�SCREW�M4-.7�X�14

X1775022 SPACER

X1775023 NOSE

X1775024 SLIDING�MAGAZINE

X1775025 SCALE

X1775058 VALVE�STEM

X1775059 COMPRESSION�SPRING

X1775060 O-RING�11�X�1.2

X1775061 PISTON�VALVE

X1775062 GROMMET

X1775063 BODY

X1775064 BUMPER

X1775065 PISTON�ASSEMBLY

X1775066 O-RING�29.7�X�3.55

X1775067 CYLINDER

X1775068 SEALING�GASKET

X1775069 O-RING�30�X�1.8

X1775070 O-RING�42.6�X�2.35

X1775071 COLLAR

X1775072 O-RING�31.2�X�2.5

X1775073 O-RING�24.8�X�3.5

X1775074 SEALING�WASHER

X1775075 ON/OFF�VALVE

X1775076 COMPRESSION�SPRING

X1775077 SEALING�WASHER

X1775078 O-RING�13�X�2.4

X1775079 CYLINDER�COVER

XPLW01M LOCK�WASHER�5MM

XPSB15M CAP�SCREW�M5-.8�X�20

X1775082 COMPRESSION�SPRING

X1775083 AIR�DEFLECTOR

X1775084 SPCL�CAP�SCR�M4-.7�X�20

X1775085 SAFETY�GLASSES

X1775086 COMPLETE�O-RING�SET

X1775026 STICKER�PLATE

X1775027 PIPE

X1775028 PIN�3.93�X�15.50

X1775029 FIXED�SEAT

XPSB22M CAP�SCREW�M4-.7�X�35

X1775031 COMPRESSION�SPRING

X1775032 CATCH�LEVER

X1775033 COMPRESSION�SPRING

X1775034 O-RING�4.5�x�1.2

X1775035 PUSHER�STICK

X1775036 PUSHER

X1775037 PUSHER�STICK

X1775038 O-RING�2.4�X�1.8

XPFH32M FLAT�HD�SCR�M4-.7�X�6

XPSB23M CAP�SCREW�M4-.7�X�12

X1775041 BAR

X1775042 SAFETY�YOKE

X1775043 ADJUSTING�NUT

-14-

Download from Www.Somanuals.com. All Manuals Search And Download.

Model W1775 Nailer/Stapler Kit

Troubleshooting

Symptom

Possible Cause Cause Possible Solution

Air leaking at

1. O-rings in trigger valve housing

are damaged.

1. O-rings must be replaced

& operation of safety nose

must be checked.

trigger valve area.

Air leaking

between housing

and hose

1. Loose screws in housing.

2. Damaged O-ring.

3. Loose air fitting.

1. Reseal and tighten screws.

2. Replace O-ring

3. Tighten air fitting & use

teflon tape.

Air leaking

1. Damaged seal.

1. Replace damaged seals.

between housing

and cap.

Tool skips nails

while discharging.

1. Excessive air pressure.

2. Air leaks.

1. Reduce air pressure to tool.

2. Reseal and tighten screws

and fittings.

3. Dirt in nose.

4. Dirt or damage prevents nails

from moving freely.

3. Clean nose.

4. Clean magazine and

inspect/repair damage.

5. Check fittings, hose,

compressor, and air

pressure.

5. Inadequate air flow to tool.

6. Worn piston O-ring or lack of

lubrication.

7. Damaged trigger valve O-rings.

6. Replace O-ring and

lubricate.

7. Replace trigger valve O-

rings.

8. Worn bumper.

9. Cap seal leaking.

8. Replace bumper.

9. Replace cap seal.

Tool runs slowly

or has a loss of

power.

1. Undersized air hose.

2. Nailer/stapler is not lubricated. 2. Lubricate nailer/stapler.

3. Broken spring in cap assembly.

4. Exhaust port in cap is blocked.

1. Use a larger hose.

3. Replace spring.

4. Clean or replace damaged

internal parts.

Fasteners

1. Fasteners are the wrong size.

1. Use correct nails.

2. Follow lubricating

instructions.

frequently jam the 2. Nailer is not lubricated.

nailer/stapler.

3. Fasteners are bent or dirty.

3. Use undamaged, clean nails.

4. Magazine or nose screws are

loose.

5. Driver or driver guide are worn

or damaged.

4. Tighten magazine.

5. Replace worn or damaged

parts.

Nailer/stapler does 1. Fastener is jammed in magazine 1. Clear magazine or discharge

not fire.

or discharge area.

2. Piston shaft is damaged.

3. Air pressure too low.

area.

2. Replace piston shaft.

3. Check/increase air pressure.

-15-

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty Registration

Name___________________________________________________________________________________

Street __________________________________________________________________________________

City _________________________State___________________________Zip________________________

Phone #______________________Email __________________________Invoice #___________________

Model #_________Serial #______________Dealer Name__________________Purchase Date___________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us

develop better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

_____ Advertisement

____ Friend

____ Website

____ Local Store

____ Other:

_____ Mail Order Catalog

2. How long have you been a woodworker/metalworker?

_____ 0-2 Years

_____ 2-8 Years

____8-20 Years

_____ 20+ Years

3. How many of your machines or tools are Shop Fox?

_____ 0-2

_____ 3-5

____6-9

_____ 10+

____ No

4. Do you think your tool represents a good value?

_____ Yes

5. Would you recommend Shop Fox products to a friend? _____ Yes

6. What is your age group?

_____ 20-29

_____ 50-59

____ 30-39

____ 60-69

____ 40-49

____ 70+

7. What is your annual household income?

_____ $20,000-$29,000

_____ $50,000-$59,000

____ $30,000-$39,000

____ $60,000-$69,000

____ $40,000-$49,000

____ $70,000+

8. Which of the following magazines do you subscribe to?

____ Cabinet Maker

____ Family Handyman

____ Hand Loader

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Practical Homeowner

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Modeltec

____ Old House Journal

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Riﬂe

____ Shop Notes

____ Shotgun News

9. Comments:__________________________________________________________________

_____________________________________________________________________________

___________________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Download from Www.Somanuals.com. All Manuals Search And Download.

Weslo Treadmill 831248220 User Manual
West Bend Oven L5658B User Manual
Westinghouse Microwave Oven WCM660W User Manual
Wolf Oven DO30F User Manual
Xantech Stereo System BXAUDIO4X4 User Manual
Zanussi Oven 291501 User Manual
Zanussi Range ZCM 631 User Manual
Zanussi Refrigerator Z16 12R User Manual
Zanussi Refrigerator ZRB 3225 X User Manual
Z Microsystems Network Card Z MPU User Manual