MODEL W1694
6" BENCH TOP JOINTER
INSTRUCTION MANUAL
COPYRIGHT © JULY, 2003 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION ............................................................................................2
About Your New Jointer ......................................................................................2
Woodstock Service and Support ..............................................................................2
Warranty and Returns..........................................................................................3
Specifications ..................................................................................................3
SAFETY ......................................................................................................4
Standard Safety Instructions ..................................................................................4
Know Your Machine ............................................................................................6
Safety Instructions for Your Jointer ........................................................................7
Avoiding Potential Injuries ....................................................................................8
ELECTRICAL REQUIREMENTS ............................................................................9
110V Operation..................................................................................................9
Extension Cords ................................................................................................9
Grounding ........................................................................................................9
ASSEMBLY..................................................................................................10
Unpacking ......................................................................................................10
Inventory........................................................................................................10
Shop Preparation ..............................................................................................11
Dust Collection ................................................................................................11
Initial Cleaning ................................................................................................11
Rubber Feet ....................................................................................................12
Fence Support..................................................................................................12
Fence Assembly................................................................................................13
90˚ Stop Slide..................................................................................................14
Dust Port........................................................................................................14
ADJUSTMENTS ............................................................................................16
Fence............................................................................................................16
Fence Angle Stops ............................................................................................17
Blade Height....................................................................................................19
Depth Of Cut ..................................................................................................20
Blade Guard ....................................................................................................21
OPERATIONS ..............................................................................................22
Test Run ........................................................................................................22
Operation Requirements ....................................................................................23
Surface Planing ................................................................................................24
Edge Jointing ..................................................................................................25
Bevel Cutting ..................................................................................................26
MAINTENANCE ............................................................................................27
General..........................................................................................................27
Table Surface ..................................................................................................27
Sharpening Blades ............................................................................................27
Replacing Blades ..............................................................................................28
Guard Spring ..................................................................................................29
Lubrication ....................................................................................................29
Drive Belts......................................................................................................30
Motor Brushes ..................................................................................................30
Troubleshooting ..........................................................................................31
Parts ........................................................................................................35
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
About Your New Jointer
Your new SHOP FOX® Model W1694 6" Bench Top Jointer is specially designed to provide many years
of trouble-free service. Close attention to engineering detail, ruggedly built parts, and a rigid quality
control program assure safe and reliable operation.
The Model W1694 features a 2 HP, 110V motor, which is capable of 19,000 RPM. The Model W1694 also
features a two knife cutterhead with HSS blades, a 23⁄8" dust port with a high-powered suction impeller,
1
a maximum cutting depth of ⁄8", a maximum cutting width of 61⁄8", and a minimum cutting length of
81⁄8".
For more features and details, refer to the Specifications section in this manual.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to include all the information necessary for safety, ease of assembly, practical use and durabili-
ty of this product.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock International, Inc.
Attn: Technical Support Department
P.O. Box 2309
Bellingham, WA 98227
Woodstock Service and Support
We stand behind our machines! In the event that a defect is found, parts are missing or questions arise
about your machine, please contact Woodstock International Service and Support at 1-360-734-3482 or
send e-mail to: [email protected]. Our knowledgeable staff will help you troubleshoot problems,
order parts or arrange warranty returns.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Returns
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-
manship and materials for a period of 2 years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or acci-
dents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone other
than Woodstock International, Inc.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facil-
ity designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years,
and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through
inspection. If it is determined there is no defect, or that the defect resulted from causes not within the
scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing
and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with
the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this war-
ranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event
be liable for death, injuries to persons or property or for incidental, contingent, special or consequen-
tial damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabili-
ty standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Specifications
Motor Size ..........................................................2 HP, 110V, Universal-Type Motor
Motor Speed....................................................................................10,000 RPM
Amp Draw ..............................................................................................12 A
Maximum Cutting Depth................................................................................1⁄8
Maximum Cutting Width ..............................................................................61⁄8
Minimum Cutting Length..............................................................................81⁄8
"
"
"
Cutterhead Blades....................................................................................2 HSS
Machine Weight ..................................................................................921⁄2 lbs
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury, MAY result in property damage.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
Standard Safety Instructions
1. Thoroughly read the instruction manual before operating your machine. Learn the applications,
limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future
reference.
2. Keep work area clean and well lit. Clutter and inadequate lighting invite potential hazards.
3. Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a three-
hole grounded electrical receptacle or grounded extension cord. If using an adapter to aid in accom-
modating a two-hole receptacle, ground using a screw to a known ground.
4. Wear eye protection at all times. Use safety glasses with side shields or safety goggles that meet
the appropriate standards of the American National Standards Institute (ANSI).
5. Avoid dangerous environments. DO NOT operate this machine in wet or open flame environments.
Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure all guards are securely in place and in working condition.
7. Make sure the machine power switch is in the OFF position before connecting power to machine.
8. Keep the work area clean, free of clutter, grease, etc.
9. Keep children and visitors away. Visitors should be kept at a safe distance while operating unit.
10.Childproof your workshop with padlocks, master switches or by removing starter keys.
11.Stop and disconnect the machine when cleaning, adjusting or servicing.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
12.DO NOT force tool. The machine will do a safer and better job at the rate for which it was designed.
13.Use correct tool. DO NOT force machine or attachment to do a job for which it was not designed.
14.Wear proper apparel. DO NOT wear loose clothing, neck ties, gloves, jewelry; and secure long hair
away from moving parts.
15.Remove adjusting keys, rags, and tools. Before turning the machine on, make it a habit to check
that all adjusting keys and wrenches have been removed.
16.Avoid using an extension cord. But if you must, examine the extension cord to ensure it is in good
condition. Use the “Extension Cord Requirements” table below to determine the correct length and
gauge of extension cord needed for your particular needs. The amp rating of the motor can be found
on its nameplate. If the motor is dual voltage, be sure to use the amp rating for the voltage you will
be using. If you use an extension cord with an undersized gauge or one that is too long, excessive
heat will be generated within the circuit, increasing the chance of a fire or damage to the circuit.
Always use an extension cord that uses a ground pin and connected ground wire. Immediately replace
a damaged extension cord.
17.Keep proper footing and balance at all times and lock mobile base from freely rolling before using
your machine.
18. DO NOT leave machine unattended. Wait until it comes to a complete stop before leaving the area.
19.Perform machine maintenance and care. Follow lubrication and accessory attachment instructions
in the manual.
20.Keep machine away from open flame. Operating machines near pilot lights and/or open flames cre-
ates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause an
explosion. DO NOT operate the machine in high-risk areas, including but not limited to, those men-
tioned above.
21.If at any time you are experiencing difficulties performing the intended operation, stop using the
machine! Contact our service department or ask a qualified expert how the operation should be per-
formed.
22. Habits are hard to break. Develop good habits in your shop and consistent safety practices will
become second-nature to you.
Extension Cord Requirements
Operating this equipment creates the
Length And Gauge
25ft 50ft 100ft
potential for flying debris to cause eye
injury. Always wear safety glasses or gog-
gles when operating equipment. Everyday
glasses or reading glasses only have impact
resistant lenses, they are not safety glasses.
Be certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).
Amp Rating
0-6
#16
#16
#16
#14
#12
#10
#16
#16
#16
#12
#12
#10
#16
#14
#14
#12
#10
No
7-10
11-12
13-16
17-20
21-30
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Know Your Machine
An important part of safety is knowing your machine and its components. Please take the time to learn
the items shown in the pictures below. The letters in the picture correspond to the following descrip-
tions in the text.
C
D
B
E
A
F
G
I
H
J
L
M
K
H. Power Switch
A. Outfeed Table
B. Fence
C. Cutterhead Blade Guard
D. Infeed Table
E. Jointer Body
F. Rubber Feet
G. Cutterhead Access Cover
I. Dust Port
J. 90˚ Stop Slide
K. Fence Sliding Handle
L. Fence Tilting Handle
M. Table Height Knob
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions for Your Jointer
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
not understood and fol-
lowed. DO NOT risk your
safety by not reading!
Use this and other machinery with caution
and respect. Always consider safety first, as
it applies to your individual working condi-
tions. No list of safety guidelines can be com-
plete—every shop environment is different.
Failure to follow guidelines could result in
serious personal injury, damage to equip-
ment or poor work results.
1. JOINTING SAFETY BEGINS WITH YOUR LUMBER. Inspect your workpiece carefully before you feed
it over the cutterhead. If you have any doubts about the stability or structural integrity of your
workpiece, DO NOT JOINT IT! Unstable workpieces can result in kickback.
2. MAINTAIN THE PROPER ALIGNMENT of the outfeed table with the cutterhead knife.
3. ALWAYS USE PUSH BLOCKS WHEN JOINTING. Never allow your hands to get near the cutterhead.
4. SUPPORT AND MAINTAIN CONTROL OVER THE WORKPIECE at all times during operation.
5. WHEN JOINTING, DO NOT STAND DIRECTLY BEHIND THE WORKPIECE. Position yourself just to the
side of the infeed table to avoid possible kickbacks.
6. NEVER MAKE CUTS deeper than 1⁄8".
7. NEVER JOINT A WORKPIECE THAT HAS LOOSE KNOTS, NAILS, STAPLES, OR EMBEDDED
DIRT/STONES. All defects and foreign objects should be removed before use.
8. NEVER JOINT END GRAIN.
9. ALL OPERATIONS MUST BE PERFORMED WITH THE GUARD IN PLACE.
10. NEVER CHANGE FEEDING DIRECTIONS DURING A CUT. Any time the workpiece moves backwards,
the chances of kickback and injury are greatly increased.
11. “KICKBACK” is when the workpiece is thrown off the jointer table from the force of the cutterhead.
Always use push blocks and safety glasses to reduce the likelihood of injury from “kickback.” If you
do not understand what kickback is, or how it occurs, DO NOT operate this machine.
12. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION in people and animals,
especially when exposed to fine dust. Make sure you know what type of wood dust you will be
exposed to and always wear an approved respirator.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoiding Potential Injuries
Figure 1. Correct operator and workpiece position,
guard is in place, and push blocks are being used.
Figure 2. Never surface plane without push blocks!
Figure 3. Never stand directly behind
the workpiece!
Figure 4. Never plane/edge-joint with
Figure 5. Never joint end grain!
the guard removed!
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REQUIREMENTS
110V Operation
Grounding
The SHOP FOX® Model W1694 2 HP, 110 volt
motor draws approximately 12 amps.
Serious injury or fire may
Since other machines may be using the same
circuit, make sure the circuit, circuit breaker,
or fuse can carry the total load without tripping.
If the total amperage load of all machines and
the jointer exceeds the amperage rating of the
circuit breaker or fuse, use a different circuit
that can carry the load.
occur if you plug this
machine into a receptacle
that is not grounded.
Connect this machine to
grounded outlets only!
Ground this machine! The electrical cord sup-
plied with the SHOP FOX® Model W1694 Jointer
has a three prong plug for grounded outlets. See
Figure 6. If your power receptacle does not have
a ground pin hole, have the receptacle replaced
by a qualified electrician, or have an appropriate
adapter installed and grounded properly. NEVER
cut the ground pin off so your jointer will plug
into a non-grounded receptacle.
DO NOT modify an existing low-amperage circuit
by only replacing the circuit breaker with a
breaker rated for a higher amperage. The break-
er and the complete circuit must be replaced by
a qualified electrician, otherwise the wires can
overheat and cause a fire.
Extension Cords
NOTICE
If you must use an extension cord with the Model
W1694, please follow these requirements:
When using an electrical plug adapter, make
sure the adapter is grounded.
•Use a cord rated for Standard Service
(Grade S).
•Use a 14 AWG cord that is 100 feet or less
•Use a cord with a ground pin
•Use an undamaged cord only
Remember, an adapter with a grounding wire
does not guarantee the jointer is grounded. A
ground source must always be verified in the
electrical circuit within the wall or conduit.
Figure 6. NEMA-style 5-15 plug and receptacle.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
7
8
10
9
6
5
13
12
14
11
15
4
1
2
Figure 7. Loose parts shipped with the jointer.
3
Inventory
The Model W1694 is a
heavy machine at 921⁄2
lbs. Use assistance
when lifting or moving
the machine.
Item
Qty
1. Filter Bag ......................................1
2. Trash Bag Support Segments................3
3. Connectors ....................................3
4. Fence ..........................................1
5. Push Blocks ....................................2
6. Fence Support ................................1
7. 90˚ Slide Stop ................................1
8. Rubber Feet....................................4
9. Fence Tilting Handle ........................1
10.Filter Bag Spring ..............................1
11.Hardware Bag..................................1
• Cap Screws M8-1.25 x 20 ..................6
• Flat Washers 8mm ..........................6
• Allen Wrench Set ............................1
• Handle Spacers ..............................2
12.Locking Plate Assembly ......................1
13.Fence Sliding Handle ........................1
14.Fence Adjusting Bracket ....................1
15.Dust Port........................................1
Unpacking
The Model W1694 was carefully packed when it
left our warehouse. If you receive it damaged or
missing any parts, please contact Woodstock
International Service and Support at 1-360-734-
3482 or send e-mail to:[email protected].
Layout and inventory the package contents list-
ed to the right and familiarize yourself with the
components shown in Figure 7 to ease assembly.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Shop Preparation
Initial Cleaning
The exposed and unpainted jointer surfaces are
coated with a waxy oil to prevent rust during
storage and shipment. DO NOT use chlorine
based solutions or solvents to remove the this
waxy oil, or you will damage the painted sur-
faces. Remove the waxy oil with a solvent based
degreaser before you use the jointer. Always
follow all usage and safety instructions of the
product that you are using.
ONLY ALLOW TRAINED
PEOPLE in your shop! Make
sure shop entrances are
locked and machines are
correctly turned off with
lock-out devices when not
in use. Otherwise, injury
or death can occur.
DO NOT use flammables
such as gas or other
petroleum-based solvents
to clean your machine.
These products have low
flash points and present
the risk of explosion and
severe personal injury!
•
•
•
Lighting: Lighting should be bright enough
to eliminate shadows and prevent eye
strain.
Working Clearances: Consider your current
and future shop needs with respect to the
safe operation of this machine.
Outlets: Make sure the electrical circuits
have the capacity to handle the amperage
requirements for your Model W1694. Refer
to page 9 for more information. Electrical
outlets should be located near the lathe, so
power or extension cords are clear of high-
traffic areas.
DO NOT smoke while
using cleaning solvents.
Smoking
may
cause
explosion or risk of fire
when exposed to these
products!
Dust Collection
THIS MACHINE produces
sawdust that may cause
allergic reactions or res-
piratory problems. Wear
a dust mask or respirator
in addition to using a dust
collection system.
ALWAYS work in a well
ventilated area when
using
solvents
with
fumes, and keep away
from any potential igni-
tion
sources
(pilot
lights). Most solvents
used to clean machinery
are toxic when inhaled
or ingested. Always dis-
pose of waste rags in a
sealed container to make
sure they do not cause
fire or environmental
hazards.
For information on the correct dust collection
components for the jointer, contact your
Woodstock International dealer for a copy of the
Dust Collection Basics handbook and available
accessories.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPLUG POWER CORD
before you do any assem-
bly or adjustment tasks!
Otherwise, serious per-
sonal injury to you or oth-
ers may occur!
Rubber Feet
READ and understand this
entire instruction manual
before performing any
operations with your
machine. Serious personal
injury may occur if safety
and operational informa-
tion is not understood and
followed.
Figure 8.
Attached rubber feet.
Rubber Feet
To attach the rubber feet, do these steps:
Slide the four rubber feet onto the four corners
of the jointer base (Figure 8).
Figure 9. Aligning the fence support.
Fence Support
To attach the fence support, do these steps:
Locking Plate
1. Align the fence support with the mounting
holes on the back of the jointer (Figure 9).
Make sure the slot on the top of the fence
support is positioned correctly.
2. Secure the fence support to the jointer with
two 8mm flat washers and two M8-1.25 x 20
cap screws.
3. Secure the locking plate assembly to the
fence support with the fence sliding handle
(Figure 10).
Figure 10. Secured locking plate.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Assembly
The fence assembly consists of the fence, the
fence adjusting bracket, and the fence tilting
handle.
To assemble the fence assembly, do these
steps:
1. Attach the fence to the fence adjusting
bracket with four 8mm flat washers and
four M8-1.25 x 20 cap screws (Figure 11).
2. Slide the fence assembly over the dovetail
way and onto the fence support (Figure
12).
Figure 11.
Attaching the fence to the fence
adjusting bracket.
3. Secure the fence assembly to the fence sup-
port by tightening the fence sliding handle.
4. Secure the fence position by threading the
fence tilting handle through the fence
adjusting bracket (Figure 13). Further
adjustment of the fence will be discussed in
the Adjustments section.
Dovetail Way
Figure 12. Fence assembly on dovetail way.
Fence Tilting
Handle
Figure 13. Securing the fence tilting handle.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
90˚ Stop Slide
To install the 90˚ stop slide, do these steps:
Slide the 90˚ stop slide under the limit plate as
shown in Figure 14. Do not worry about its exact
position at this time. Further adjustment of the
90˚ stop slide will be discussed in the
Adjustments section.
Dust Port
Figure 14.
Installing the 90˚ stop slide.
The Model W1694 has a 21⁄2" dust port with a
built-in suction impeller. The dust port can con-
nect to a standard 30 gallon trash can or a 30
gallon plastic trash bag.
To connect the dust port to a trash can, do
these steps:
1. Slip the filter bag spring into the filter bag
arm (Figure 15).
2. Slide the filter bag arm over the dust port.
3. Secure the filter bag over the rim of the
trash can with the filter bag band (Figure
16).
Figure 15. Correctly installed filter bag
spring.
Figure 16. Filter bag secured to
the trash can.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
To connect the dust port to a trash bag, do
these steps:
1. Slip the filter bag spring into the filter bag
arm.
2. Slide the filter bag arm over the dust port.
3. Assemble the trash bag support by sliding
the connectors into the channels of the
trash bag support segments (Figure 17).
4. Slide the opening of the trash bag inside and
over the trash bag support (Figure 18). Let
the trash bag hang over approximately 3"-
4".
Figure 17. Assembling the trash bag support.
5. Secure the filter bag to the trash bag/sup-
port assembly with the filter bag band
(Figure 19). Make sure the filter bag band
rests in the channel of the trash bag sup-
port.
Figure 18. Sliding the trash bag over the trash
bag support.
Figure 19. Filter bag secured to
the trash bag.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
UNPLUG the power cord
before you do any assem-
bly or adjustment tasks!
Otherwise, serious per-
sonal injury to you or oth-
ers may occur!
Fence Tilting
Handle
Fence Sliding
Handle
Fence
The fence assembly has two primary methods of
adjustment:
Figure 20. Fence bracket assembly.
•
•
The face of the fence is adjustable relative
to the table surface.
The fence position is adjustable across the
width of the table.
To adjust the fence face angle relative to the
table surface, do these steps:
1. Loosen the fence tilting handle (Figure 20).
2. Move the fence face to the desired position.
Precise angle stops will be discussed in the
Fence Angle Stops sub-section.
3. Tighten the fence tilting handle.
To adjust the fence position across the width
of the table, do these steps:
1. Loosen the fence sliding handle (Figure 20).
2. Move the fence to the desired position
across the width of the table. The fence
position is adjustable to accommodate
workpieces of varying widths and to pro-
mote even blade usage and wear.
3. Tighten the fence sliding handle.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
Fence Angle Stops
There are three fence angle stops: 90˚, 45˚
inward, and 45˚ outward. The angle stops allow
the fence to be quickly and accurately posi-
tioned at various angles.
To adjust the 90˚ angle stop, do these steps:
1. Using a machinist’s square, position the
fence 90˚ relative to the table surface
(Figure 21).
Figure 21. Setting the fence to 90˚.
2. Position the limit plate in the forward slot
of the 90˚ slide stop.
3. Loosen the jam nut on the 90˚ stop slide.
4. Using a flat-head screwdriver, adjust the
setscrew on the 90˚ stop slide until the peg
makes contact with the back of the fence
(Figure 22).
5. Retighten the jam nut loosened in step 3.
Figure 22. Adjusting the 90˚ stop slide.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the 45˚ inward angle stop bolt, do
these steps:
1. Slide the 90˚ stop slide away from the back
of the fence.
2. Using a 45˚ square, position the fence 45˚
relative to the table surface.
3. Loosen the jam nut on the 45˚ inward stop
bolt (Figure 23).
4. Adjust the 45˚ inward stop bolt until it
makes contact with the back of the fence.
Figure 23. 45˚ inward angle stop bolt.
5. Retighten the jam nut loosened in step 3.
To adjust the 45˚ outward angle stop bolt, do
these steps:
1. Using a sliding bevel adjusted to 135˚, posi-
tion the fence 135˚ (45˚ outward) relative
to the table surface.
2. Loosen the jam nut on the 45˚ outward stop
bolt (Figure 24).
3. Adjust the 45˚ outward stop bolt until it
makes contact with the fence adjusting
bracket.
4. Retighten the jam nut loosened in step 2.
Figure 24. 45˚ outward angle stop bolt.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Height
Top Dead
Center
The blade height must be adjusted correctly to
increase the time between sharpenings, allow
maximum performance, and to ensure a flat
jointed surface. Check the blade height when-
ever the blades are removed from the cutter-
head or whenever cutting performance begins to
degrade.
To check the cutterhead blade height, do
these steps:
1. UNPLUG THE JOINTER!
Figure 25. Blade is positioned at its highest
2. Use a 61⁄4" wide piece of wood to prop the
position (Top Dead Center).
blade guard open.
3. Rotate the cutterhead until one of the
blades is at its highest position (Figure 25).
4. Place a straightedge across the outfeed
table and over the top of the cutterhead
blade.
5. At both ends of the cutterhead, the
straightedge must just make contact with
the blade (Figure 26). Watch and make sure
the straightedge is not lifted from the out-
feed table surface when contact is made
with the cutterhead blades.
Figure 26. Checking the blade height.
• If the straightedge makes contact on
both ends of the cutterhead blade, then
continue to the next sub-section.
• If the straightedge does not make con-
tact with both ends of the cutterhead
blade, then continue to the next step.
6. Loosen the four blade clamp screws that
secure the blade in the cutterhead (Figure
27).
7. Adjust the jack screws under the blade until
both ends of the cutterhead blade make
contact with the straightedge.
8. Retighten the four blade clamping screw
and repeat steps 3 -7 on the second blade.
Figure 27. Blade clamp screws.
9. Remove the wood that is holding the blade
guard open.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Depth Of Cut
The depth of cut is equal to the distance
between the infeed table surface and the top of
the cutterhead blade at top-dead-center
(Figure 28). The depth of cut is adjusted by
raising and lowering the infeed table.
Depth Of Cut
To adjust the depth of cut:
•
Turn the table height knob (Figure 29)
clockwise to raise the infeed table, thereby
reducing the depth of cut.
Figure 28. Depth of cut.
•
Turn the knob counter-clockwise to lower
the infeed table, thereby increasing the
depth of cut.
1
Never remove more than ⁄8" of material from
the workpiece in a single pass.
Figure 29. Table height knob.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Guard
The blade guard protects the operator from the
cutterhead blades. It must be functioning cor-
rectly before performing any jointing operation.
To make sure the blade guard is functioning
correctly, do these steps:
1. UNPLUG THE JOINTER!
2. Adjust the infeed table even with the out-
feed table.
Figure 30. Blade guard in use.
3. Slide a piece of wood across the jointer as if
performing an actual jointing operation.
• The blade guard should rotate enough to
allow the wood to pass over the cutter-
head (Figure 30).
• Once the wood has passed over the cut-
terhead, the blade guard should swing
completely back over the cutterhead.
4. Swing the blade guard completely open and
release it.
• The blade guard should swing complete-
ly back over the cutterhead.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Test Run
Once assembly is complete, the machine is
ready for a test run. The purpose of a test run is
to identify any unusual noises and vibrations, as
well as to confirm that the machine is perform-
ing as intended.
THIS MACHINE throws
wood chips and sawdust.
Wear safety glasses or a
face shield during all
operations.
To test run the Model W1694, do these steps:
1. Make sure that all tools have been removed
KEEP loose clothing
rolled up and out of the
way of machinery and
keep hair pulled back.
from the jointer.
2. Turn the jointer ON.
3. Once the jointer is running, listen for any
unusual noises. The machine should run
smoothly with little or no vibrations.
• If there are any unusual noises or vibra-
tions, stop the jointer immediately by
pushing the paddle switch down.
THIS MACHINE produces
sawdust that may cause
allergic reactions or res-
piratory problems. Wear
a dust mask or respirator
in addition to using a dust
collector.
4. Unplug the jointer and investigate the
source of the noise or vibration. DO NOT
make any adjustments to the jointer while
it is plugged in. The jointer should not be
run any further until the problems are cor-
rected.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Requirements
•
•
•
Never allow hands or push blocks to come
within 4" of the cutterhead while it is mov-
ing.
Carefully inspect boards before jointing.
Defects such as twisting, knots, or cracks
could cause the workpiece to break apart.
Only use clean boards. Remove all dirt,
nails, staples, imbedded gravel, etc. from
boards before jointing. Dirt and debris can
damage the cutting edge of the cutterhead
blades, resulting in unsatisfactory results.
Figure 31.
Correct and incorrect grain
alignment to cutterhead.
•
•
DO NOT joint man-made products such as
MDF, OSB, or plywood. Also, never use lam-
inates, formica or other synthetic materi-
als.
Always joint “with” the grain. Cutting
“with” the grain is best described as feeding
boards on the jointer so the grain points
down and toward you as viewed on the edge
of the workpiece (Figure 31).
•
Avoid using wood with a high moisture con-
tent. Boards with more than 20% moisture
will cause unnecessary wear on the cutter-
head blades and motor.
1
•
•
Never take cuts deeper than ⁄8". Making
several shallow cuts will produce a better
finished result than one deep cut.
Keep work area clean and free of clutter.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
Surface Planing
Surface planing flattens the concave face of the
workpiece in preparation for surface planing on
a thickness planer (Figure 32). The flat face
allows the thickness planner to produce a work-
piece that is flat and uniformly thick.
Figure 33 shows an example of an operator
using the jointer to surface plane a workpiece.
Notice that the operator’s body is not directly
behind the workpiece and that the operator is
using push blocks.
Portion
Removed With
Jointer
To perform a surface planing operation, do
these steps:
Figure 32. Surface planing flattens the concave
face of the workpiece.
1. Read and become familiar with the
Operation Requirements sub-section.
2. Place the workpiece so the concave side is
down on the infeed table and press the
workpiece firmly against the fence.
ALWAYS wear safety
glasses to prevent seri-
ous personal injury!
3. Start the jointer.
4. Using push blocks, feed the workpiece
through the jointing operation. Make sure
to maintain even downward pressure.
5. When your leading hand gets within 4" of
the cutterhead, lift the push block up and
over the cutterhead and place it on the
workpiece as it passes over the outfeed
table. Do the same thing when your trailing
hand gets within 4" of the cutterhead and
try to maintain pressure on the outfeed
table.
6. Repeat steps 4-5 until the surface is flat.
Figure 33. This is an example of a surface
planing operation.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
Edge Jointing
Edge jointing straightens the concave edge of
the workpiece (Figure 34). This straight edge
can then be guided along the rip fence of a table
saw when squaring rough lumber. The straight,
flat edge is also used for gluing up large panel
assemblies.
Portion
Removed With
Jointer
Figure 35 shows an example of an operator edge
jointing. Notice that the operator’s body is not
directly in line with the workpiece and that he
maintains a stable hand position while keeping
the workpiece firmly on the table and against
the fence.
Figure 34. Edge jointing straightens the concave
edge of the workpiece.
To perform an edge jointing operation, do
these steps:
1. Read and become familiar with the
Operation Requirements sub-section.
ALWAYS wear safety
glasses to prevent seri-
ous personal injury!
2. Place the workpiece so the concave edge is
down on the infeed table and press the
workpiece firmly against the fence.
3. Start the jointer.
4. Feed the workpiece through the jointing
operation. Make sure to maintain even
downward pressure.
5. If your leading hand gets within 4" of the
cutterhead, lift it up and over the cutter-
head and place it on the workpiece as it
passes over the outfeed table. Do the same
thing when your trailing hand gets within 4"
of the cutterhead and try to maintain pres-
sure on the outfeed table.
6. Repeat steps 4-5 until the edge is flat.
Figure 35. This is an example of an edge
jointing operation.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Bevel Cutting
Bevel cutting is very similar to edge jointing, but
done with the fence tilted to a specific angle in
order to produce an angled edge (Figure 36).
Usually bevel cuts are made on two boards that
will be joined together at a corner.
For bevel cuts, the Model W1694 has preset
stops at 45˚ inward and 45˚ outward. If a dif-
ferent angle is desired, use a bevel gauge to set
the fence, then lock it in position.
Portion
Removed With
Jointer
Figure 37 shows an example of an operator
bevel cutting at 45˚ outward. Notice that the
operator’s body is not directly in line with the
workpiece and that he maintains a stable hand
position while keeping the workpiece firmly on
the table and against the fence.
Figure 36. Bevel cutting produces an angled
edge on the workpiece.
To perform a bevel cutting operation, do
these:
Always wear safety
glasses to prevent seri-
ous personal injury!
1. Read and become familiar with the
Operation Requirements sub-section.
2. Set the fence to the desired angle. Place
the workpiece down on the infeed table and
press it firmly against the fence.
3. Start the jointer.
4. Keep the workpiece firmly against the table
and fence, and feed the workpiece into the
cutterhead.
5. When your leading hand gets within 4" of
the cutterhead, lift the push block up and
over the cutterhead and place it on the
workpiece as it passes over the outfeed
table. Do the same thing when your trailing
hand gets within 4" of the cutterhead and
try to maintain pressure on the outfeed
table.
Figure 37. This is an example of a bevel cut-
ting operation with the fence set at 45˚.
6. Repeat steps 4-5 until the edge is flat.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General
Regular periodic maintenance on your Model
W1694 will ensure its optimum performance.
Make a habit of inspecting your machine each
time you use it. Check for the following condi-
tions and repair or replace when necessary:
Make sure that your
machine is unplugged
during any maintenance
procedures
except
where instructed other-
wise! If this warning is
ignored, serious person-
al injury may occur.
•
•
•
•
Loose mounting bolts.
Worn switch.
Worn or damaged cords and plugs.
Any other condition that could hamper the
safe operation of this machine.
Table Surface
Tables can be kept rust-free with regular appli-
cations of products like SLIPIT®. For long term
storage you may want to consider products like
Boeshield T-9™. Whichever product you ulti-
mately choose for a table lubricant, make sure
that it protects against rust, allows the work-
piece to slide easily and will not stain expensive
workpieces.
Sharpening Blades
Correct blade sharpening and honing techniques
are beyond the scope of this manual. Have the
blades professionally sharpened for the best
results.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Blades
To replace the cutterhead blades, do these
steps:
1. UNPLUG THE JOINTER!
2. Use a 61⁄4" wide piece of wood to prop the
blade guard open.
3. Remove the four blade clamping screws on
one of the blades (Figure 38).
4. Remove the blade and clamp from the cut-
terhead.
Figure 38. Blade clamping screws.
5. Slide the replacement blade and clamp into
the cutterhead.
6. Place a straightedge across the outfeed
table and over the top of the cutterhead
blade.
7. At both ends of the cutterhead, the
straightedge must make contact with the
blade (Figure 39). Watch and make sure
the straightedge is not lifted from the out-
feed table surface when contact is made
with the cutterhead blades.
• If the straightedge makes contact on
both ends of the cutterhead blade, then
continue to step 9.
Figure 39. Checking the blade height.
• If the straightedge does not make con-
tact with both ends of the cutterhead
blade, then continue to the next step.
8. Adjust the jack screws under the blade until
both ends of the cutterhead blade make
contact with the straightedge (Figure 40).
9. Retighten the four blade clamping screws
loosened in step 3 and repeat steps 3-7 on
the second blade.
10. Remove the wood that is holding the blade
guard open.
Figure 40. Jack screws.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
Guard Spring
To replace a worn out blade guard spring, do
these steps:
1. Lay the jointer on its side so the switch is
facing up.
2. Remove the bottom cover.
3. Remove the screw that secures the blade
guard from beneath and remove the blade
guard (Figure 41).
Figure 41. Blade guard mounting screw.
4. Remove the screw that secures the blade
guard spring and remove the spring (Figure
42). Make note of the spring position
before removal. This will simplify installing
the new spring.
5. Reverse the above steps to re-install the
blade guard.
6. Test the blade guard to make sure it is func-
tioning correctly.
Lubrication
Since all bearings are sealed and permanently
lubricated, simply leave them alone until they
need to be replaced. Do not lubricate them.
Figure 42. Blade guard spring.
For the moving mechanisms on the fence assem-
bly, an occasional application of light machine
oil is all that is necessary. Before applying lubri-
cant, wipe the fence clean. Lubricate the pivot
points and move the fence back and forth as
shown in Figure 43. Your goal is to achieve ade-
quate lubrication. Too much lubrication will
attract dirt and sawdust.
Finally, keep the sliding surfaces clean and free
of any dirt or sawdust. Give these areas, espe-
cially the key and keyway, an application of
powdered graphite. Powdered graphite works
great because it does not attract dirt or saw-
dust.
Figure 43. Lubricating fence pivot points.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Belts
To replace the drive belts, do these steps:
1. Lay the jointer on its side so the switch is
facing up.
2. Remove the bottom cover.
3. Loosen the screws securing the motor
mount plate and the impeller mount plate
(Figure 44).
4. Adjust the mounting plate to allow the drive
Figure 44. Motor and impeller
belts to loosen.
mount plate screws.
5. Remove the drive belts.
6. Replace or re-install the drive belts, making
sure they are aligned correctly.
7. Replace the bottom cover.
Motor Brushes
To replace the drive belts, do these steps:
1. Lay the jointer on its side so the switch is
facing up.
Figure 45. Motor brush caps.
2. Remove the bottom cover.
3. Using a flat-head screwdriver, remove the
motor brush caps (Figure 45).
4. Replace the motor brushes if they are dam-
aged or severely blackened by carbon build-
up.
5. Re-install the motor brush caps.
6. Replace the bottom cover.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SYMPTOM
POSSIBLE REASON
HOW TO REMEDY
Motor will not start and fuses or
breakers blow.
1. Short circuit in line cord or plug.
1. Inspect cord or plug for damaged insulation and shorted
wires.
2. Short circuit in motor or loose con- 2. Inspect all connections on motor for loose or shorted ter-
nections. minals or worn insulation.
3. Incorrect fuses or circuit breakers in 3. Replace with correct fuses or circuit breakers.
power line.
Motor will not start.
Motor overheats.
1. Voltage too low.
1. Call an electrician to correct power line voltage.
2. Open circuit in motor or loose con- 2. Inspect all lead connections on motor for loose or open
nections.
connections.
1. Motor overloaded.
1. Reduce load on motor.
2. Restricted air circulation through 2. Clean out motor to provide proper circulation.
motor.
Motor stalls, resulting in blown
fuses or tripped breaker.
1. Short circuit in motor or loose con- 1. Inspect connections on motor for loose or shorted termi-
nections.
nals or worn insulation.
2. Voltage too low.
2. Call an electrician to correct power line voltage.
3. Incorrect fuses or circuit breakers in 3. Replace with correct fuses or circuit breakers.
power line.
4. Motor overloaded.
4. Reduce load placed on motor.
Loud, repetitious noise coming
from jointer.
1. Pulley setscrews or keys are missing 1. Replace or tighten setscrews or keys if necessary.
or loose.
2. Motor fan is hitting the cover.
3. V-belt is defective.
2. Tighten fan or shim motor cover.
3. Replace V-belt. See page 28.
Jointer slows when operating.
1. Too fast of a feed rate.
2. Too deep of cut.
1. Feed workpiece at a slower rate.
2. Decrease depth of cut.
Jointer cuts loud, overheats or
bogs down in cut.
1. Too deep of cut.
2. Blades are dull.
1. Decrease depth of cut.
2. Replace blades.
Gouge in the workpiece that is
uneven with rest of cut (snipe).
1. End of workpiece is being pressed on 1. Maintain even pressure on the workpiece though the
as it passes over the cutterhead. entire jointing operation.
2. Knives are not set at the correct 2. Re-adjust the blade height.
height.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SYMPTOM
POSSIBLE REASON
HOW TO REMEDY
Chipping occurs on workpiece.
1. Grain direction incorrect or knots in 1. Feed workpiece with the grain. Inspect workpiece for
workpiece.
knots or try again with different workpiece.
2. Replace blades.
2. Dull blades.
3. Too fast of a feed rate.
4. Too deep of cut.
3. Feed the workpiece at a slower rate.
4. Decrease depth of cut.
Grain is fuzzy after jointing.
1. Wood may have high moisture con- 1. Allow wood to dry.
tent. Check with moisture meter.
2. Dull blades.
2. Replace blades.
3. Wood is figured or is a species that 3. Use different wood or plan on extra sanding.
has naturally fuzzy characteristics.
Lines or ridges in workpiece.
1. Nicked or chipped blades.
1. Inspect blades. Replace if necessary.
Uneven blade marks on work-
piece.
1. One or more cutterhead blades are 1. Inspect blades. Replace if necessary.
worn.
Wavy surface or chatter marks on 1. Too fast of a feed rate.
1. Feed the workpiece at a slower rate.
workpiece.
2. One or more cutterhead blades are 2. Inspect blades. Replace if necessary.
worn.
Edge is concave or convex after
edge jointing.
1. Workpiece not held with even pres- 1. Hold workpiece with even pressure as it moves through
sure on infeed and outfeed table.
2. Workpiece began too uneven.
the cutterhead. See “Edge Jointing” on page 24.
2. Take partial cuts to remove extreme high spots before
doing a full pass.
3. Workpiece has excessive bow or 3. Surface plane one face so there is a good surface to posi-
twist along its length.
tion against the fence.
4. Insufficient number of passes.
4. Three to five passes may be needed to achieve a perfect
edge, depending on starting condition and depth of cut.
5. Outfeed table not properly aligned 5. Set outfeed table even with cutterhead blade at top dead
with cutterhead. center. See page 18-19.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
Closure
The following pages contain parts diagrams/lists
We recommend you keep this manual for com-
plete information regarding Woodstock
International, Inc.’s warranty and return policy.
Should a problem arise, we recommend that you
keep your proof of purchase with your manual.
If you need additional technical information
relating to this machine, or if you need general
assistance or replacement parts, please contact
the Service Department at 1-360-734-3482 or e-
mail: [email protected].
and a warranty card for your SHOP FOX® Model
W1694.
If you need parts or help in assembling your
machine, or if you need operational informa-
tion, we encourage you to call our Service
Department. Our trained service technicians will
be glad to help you.
If you have comments dealing specifically with
this manual, please write to us using the address
in the General Information. The specifications,
drawings, and photographs illustrated in this
manual represent the Model W1694 as supplied
when the manual was prepared. However, due
to Woodstock International, Inc.’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of
Woodstock International, Inc. Whenever possi-
ble, though, we send manual updates to all own-
ers of a particular tool or machine that have reg-
istered their purchase with our warranty card.
Should you receive one, add the new informa-
tion to this manual and keep it for reference.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your
local library are good places to start.
The Model W1694 is specifically designed for
jointing operations. DO NOT MODIFY AND/OR
USE THIS MACHINE FOR ANY OTHER PURPOSE.
MODIFICATIONS OR IMPROPER USE OF THIS
TOOL WILL VOID THE WARRANTY. If you are
confused about any aspect of this machine, DO
NOT use it until all your questions have been
answered.
We have included some important safety mea-
sures that are essential to this machine’s opera-
tion. While most safety measures are generally
universal, we remind you that each workshop is
different and safety rules should be considered
as they apply to your specific situation.
ALWAYS wear safety glasses or goggles when
operating this machine. This machine cre-
ates the potential for flying debris, which
can cause eye injury. Everyday glasses or
reading glasses only have impact resistant
lenses, they are not safety glasses. Be cer-
tain the safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
As with all power tools, there is danger
associated with the Model W1694. Use the
tool with respect and caution to lessen the
possibility of mechanical damage or opera-
tor injury. If normal safety precautions are
overlooked or ignored, injury to the opera-
tor or others in the area is likely.
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1694 Wiring Diagram
Switch
White
Black
White
Black
To 110V ꢀ
Single-Phase ꢀ
Power Source
To Motor
Green
Green
Ground
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
3
21
19
18
20
5
6
12
11
17
15
3
2
25
26
4
9
8
10
24
12
16
23
13
14
4
2
47
33
3
22
32
7
6
38
37
38
1
39
9
27
8
35
3
40
41
28
44
29
30
31
46
42
43
14
45
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
X1694001 FENCE
25 X1694025 TABLE PIN
26 X1694026 FRAME PIN
27 X1694027 FENCE SUPPORT
28 X1694028 PIN
XPN06M
XPN01M
XPB94M
HEX NUT M5-.8
HEX NUT M6-1
HEX BOLT M5-.8 X 25
X1694005 HANDLE
X1694006 SPACER
X1694007 FENCE PLATE
XPLW04M LOCK WASHER 8MM
29 X1694029 LOCKING PLATE
30 XPN03M
31 XPB20M
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 35
32 X1694032 TABLE FRAME
33 X1694033 3CMI-6 E-RING
XPSB14M
CAP SCREW M8-1.25 X 20
10 X1694010 PLATE SHAFT
11 X1694011 RIGHT LINK
12 X1694012 PUSH NUT M10
34 XPSS28M
35 XPSS29M
SETSCREW M6-1 X 30
SETSCREW M6-1 X 35
36 X1694036 SUPPORT PLATE
37 XPLW01M LOCK WASHER 5MM
13 XPSB02M
CAP SCREW M6-1 X 20
38 XPSS11M
39 XPSW03-1 KNOB
40 X1694040 ELEVATION SCREW
41 XPW02M
42 XPSS11M
43 XPW03M
44 XPS09M
45 XPSB07M
SETSCREW M6-1 X 16
FLAT WASHER 5MM
SETSCREW M6-1 X 16
FLAT WASHER 6MM
PHLP HD SCR M5-.8 X 10
CAP SCREW M6-1 X 30
22 X1694022 HANDLE
23 X1694023 INFEED TABLE
24 X1694024 BRACKET
46 X1694046 PUSH BLOCK (SET OF 2)
47 XPSS28M SETSCREW M6-1 X 30
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
109
155
110
111
107
106
118
105
112
108
101
103
102
104
113
119
114
117
143
108
156
115
116
122
123
120
137
157
158
159
124
121
142
129
127
130
113
112
141
126
128
131
125
144
145
147
146
148
132
133
140
134
135
129
136
146
151
123
152
145
122
144
139
123
124
138
137
149
150
129
102
113
153
137
154
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
101 X1694101 BASE WITH OUTFEED TABLE
102 XP6201 BALL BEARING 6201
103 X1694103 3AMI-12 RETAINING RING
104 X1694104 STRAIN RELIEF
105 X1694105 LINE CORD
106 X1694106 SPRING
131 X1694131 FAN BELT
132 XPSBS02
133 X1694133 BLADE CLAMP
134 X1694134 BLADE (SET OF 2)
135 X1694135 CUTTERHEAD
136 X1694136 DRIVE PULLEY
SOCKET HD BTN SCR 1⁄4-20 X 5⁄8
107 X1694107 PIN
137 XPS05M
138 X1694138 ACCESS COVER
139 X1694139 JACK SCREW
PHLP HD SCR M5-.8 X 8
108 XPS38M
PHLP HD SCR M4-.7 X 10
109 X1694109 BUMPER
110 X1694110 BLADE GUARD
111 X1694111 SPRING
112 X1694112 SPACER
113 XPSB50M CAP SCREW M5-.8 X 10
114 X1694114 CHIP COLLECTOR
140 X1694140 SHAFT
141 X1694141 SWITCH
142 X1694142 SWITCH PLATE
143 X1694143 SERRATED WASHER 4
144 X1694144 BRUSH CAP
115 XPW02M
116 XPS09M
117 X1694117 CHIP EXHAUST
118 X1694118 DUST CHUTE
119 XPS26M
120 X1694120 IMPELLER
121 X1694121 CHIP BLOWER MOUNT PLATE
FLAT WASHER 5MM
PHLP HD SCR M5-.8 X 10
145 X1694145 CARBON BRUSH (SET OF 2)
146 X1694146 BRUSH HOLDER
147 X1694147 MOTOR
148 X1694148 MOTOR PULLEY
149 X1694149 MOTOR MOUNTING PLATE
150 XPLW01M LOCK WASHER 5MM
151 X1694151 CORD CLAMP
PHLP HD SCR M6-1 X 20
122 XPW03M
FLAT WASHER 6MM
152 XPSB01M CAP SCREW M6-1 X 16
153 X1694153 DRIVE BELT
154 X1694154 COVER
155 X1694155 UNPLUG JOINTER LABEL
156 X1694156 MACHINE ID/ WARNING LABEL
157 XLABEL-14 ELECTRICITY LABEL
158 X1694158 READ MANUAL LABEL
159 X1694159 GLASSES/MASK LABEL
123 XPLW03M LOCK WASHER 6MM
124 XPSB26M CAP SCREW M6-1 X 12
125 X1694125 THREAD FORMING SCREW
126 X1694126 FAN SHAFT
127 X1694127 SPACER
128 XP6000
BALL BEARING 6000ZZ
129 XPSS03M SETSCREW M6-1 X 8
130 X1694130 FAN PULLEY
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name __________________________________________________________________________________________
Street __________________________________________________________________________________________
City ____________________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_________________________________FAX___________________
MODEL #______________________________ Serial #___________________________________________________
The following information is given on a voluntary basis and is strictly confidential.
1.
Where did you purchase your SHOP FOX® machine?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Lathe
___Spindle Sander
___Table Saw
2.
How did you first learn about us?
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Advertisement
___Friend
___Mail order Catalog
___World Wide Web Site
___Local Store
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
___Other__________________________________________________
Which of the following magazines do you subscribe to.
11.
12.
13.
Which benchtop tools do you own? Check all that apply.
3.
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
___American Woodworker
___Cabinetmaker
___Today’s Homeowner
___Wood
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Other__________________________________________________
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Woodworker
___Woodworker’s Journal
___Workbench
Which portable/hand held power tools do you own? Check all that apply.
___American How-To
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Miter Saw
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
4.
5.
6.
___Backyard America
___Home Time
___The New Yankee Workshop
___This Old House
___Other__________________________________________________
___The American Woodworker
___Woodwright’s Shop
What machines/supplies would you like to see?
___Other__________________________________________________
What is your annual household income?
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
16.
What new accessories would you like Woodstock International to carry?
_________________________________________________________
_________________________________________________________
What is your age group?
Do you think your purchase represents good value?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
___Yes
Would you recommend SHOP FOX® products to a friend?
___Yes ___No
___No
7.
8.
How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
17.
Comments:________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
How would you rank your woodworking skills?
___Simple
___Advanced
___Master Craftsman
___Intermediate
9.
How many SHOP FOX® machines do you own? _____________
10.
What stationary woodworking tools do you own? Check all that apply.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL, INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|