MODEL W1783
FLOORING NAILER
OWNER'S MANUAL
(FOR MACHINES MANUFACTURED SINCE 2/07)
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED NOVEMBER, 2009 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9627TS Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful
information about proper operation of the
equipment.
NOTICE
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
Safety Instructions for Pneumatic Tools
17. DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
accessories. The use of improper
accessories may cause risk of injury.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair or
replace damaged parts.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect the
air hose and do not leave tool until it
is relieved of any built up pressure.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP USING
TOOL. Seek formal training or
research books or magazines that
specialize in pneumatic tools.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor or
spread out in a disorganized fashion.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
Additional Safety for Nailers/Staplers
1. HAND INJURIES: Do not place your
hands near the nail point of entry.
A nail can deflect and tear through
the surface of the workpiece,
5. HOSE USAGE: Make sure your air
hose is designed for the tool in
use, is in good condition, and is
long enough to reach your work
without stretching. However, an
overly long air hose in the work
area may be a tripping hazard.
puncturing your hand or fingers.
2. COMBUSTIBLE GASES: Never
connect the nailer to pressurized
oxygen or other combustible
gases as a power source. Only use
filtered, lubricated, and regulated
compressed air.
6. OPERATING QUESTIONS: If you
are not sure about the intended
operation, stop using the nailer.
Seek formal training.
3. SAFE HANDLING: Never point
the nailer at others! Do not keep
the trigger pulled when loading
fasteners, carrying, or holding
tool. Carry the nailer only by the
handle, never by any other part.
Do not carry the nailer by the air
hose. Disconnect the nailer from
the air hose when going up and
down ladders.
7. MAINTENANCE: Always disconnect
air from the nailer when servicing
or installing nails. During
maintenance, a nailer connected to
air may fire accidentally, causing
serious personal injury.
8. COMPRESSED AIR RATING: Do not
connect the nailer to compressed
air that exceeds 120 PSI.
9. CHECK VALVE: Do not use a check
valve or any other fitting that
4. CLEANING: Never use gasoline or
other flammable liquids to clean
the nailer; vapors in the nailer will
ignite by a spark and cause it to
explode.
allows air to remain in the tool.
10. MODIFICATIONS: DO NOT
modify this tool or bypass safety
mechanisms.
Never point this nailer at yourself
or another person! Always pay
attention to the direction this nailer
is pointed. Use this tool with respect
and caution to lessen the possibility
of operator or bystander injury.
Ignoring this warning may result in
serious personal injury.
Nailer/stapler accidents routinely
happen while moving the gun to
another location, such as up ladders,
to another room, or even another
job site. Always disconnect the gun
immediately after use and never
transport the gun while connected to
the air—even if the air compressor is
disconnected from its power source!
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
INTRODUCTION
Woodstock Technical
Tool Data
Support
Nail Length................................1"–2"
Magazine Capacity................. 100 Nails
Air Inlet................................1⁄4" NPT
Nailer Weight....................... 111⁄3 lbs.
Hammer Weight......................21⁄2 lbs.
Operating Pressure ...............70-110 PSI
The Model W1783 Flooring Nailer has
been specially designed to provide many
years of trouble-free service. Close atten-
tion to detail, ruggedly built parts and a
rigid quality control program assure safe
and reliable operation.
Woodstock International, Inc. is commit-
ted to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
We stand behind our tools! In the
event that questions arise about
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
[email protected]. Our knowl-
edgeable staff will help you troubleshoot
problems and process warranty claims.
Read the manual before operation.
Become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
If you need the latest edition of this
manual, you can download it from
If you have comments about this
manual, please contact us at:
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other tools with caution and respect.
Failure to do so could result in serious
personal injury, damage to equipment
or poor work results.
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
Compressed Air System
The Model W1783 is designed to be
operated at 70-110 PSI using clean,
dry, regulated, compressed air. Do not
exceed the 120 PSI maximum pressure
for your model.
Before using your nailer, regulate the
air pressure to find the optimum setting
within the specified operating range.
Start by testing the nailer at a low
setting, then increase the air pressure as
needed for satisfactory results.
Exceeding the maximum permissible
operating pressure may damage the
nailer and cause it to malfunction.
To protect yourself from personal
injury, DONOTallowtheairpressure
to exceed the recommended
pressure for this nailer!
An in-line filter/lubricator/regulator unit
can be installed as depicted in Figure 1.
This filter/lubricator/regulator unit
will protect your tool from damaging
water build-up, allow you to adjust and
maintain regulated air pressure, and
save you the inconvenience of having to
manually lubricate your tool every time
you use it.
If you plan on installing a filter/
lubricator/regulator unit in your
compressed air system, always follow the
connection instructions that come with
the unit.
Quick
Connector
Quick
Connector
Lubricator
Regulator
Your
Tool
Air
Compressor
Quick
Coupler
Quick
Coupler
Air Hose
Filter
Figure 1. Typical filter/lubricator/regulator installation order.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the tool
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model W1783.
Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
A
B
C
D
F
E
Model W1783 Inventory
Qty
A. Flooring Nailer w/1⁄2" Base Plate .... 1
B. Safety Goggles........................... 1
C. Hammer .................................. 1
D. Bottle for Oil ............................ 1
E. Hex Wrenches 4mm, 5mm.......1 Each
3
F.
⁄4" Base Plate........................... 1
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
OPERATIONS
Loading
When replacing nails in your Model
Operating
If you have not read the safety
instructions in this manual, do not
operate the nailer.
W1783, follow these guidelines:
Nails.................... L-Shaped Cleat Nails
Length: .................................... 1"–2"
Capacity:................................... 100
Before you operate your nailer, place five
to six drops of the included oil into the
quick connect fitting where the nailer
connects to the air supply.
Note: Use 11⁄2" nails to install 1⁄2" flooring,
and 2" nails to install 3⁄4" flooring.
The Model W1783 comes with two base
plates:
To load your nailer, do these steps:
1. DISCONNECT NAILER FROM THE AIR
— The thinner base plate is for use
SUPPLY!
with 3⁄4" flooring.
2. Slide a strip of nails, pointed-end
down, into the rear of the magazine,
as shown in Figure 2.
— The thicker base plate is for use
1
⁄
2" flooring.
To operate your nailer, do these steps:
1. Install the correct base plate for your
size of flooring material.
2. Place the flooring nailer on the floor
with the nail discharge facing down,
then connect the air supply.
Always point the nailer at the ground
when connecting to the air supply.
DO NOT aim it in the direction of
another person or yourself. Failure
to heed this warning could result in
serious personal injury.
Figure 2. Loading nails into the nailer.
3. Press the button inside the pusher
(see inset photo, Figure 2), pull the
pusher all the way back, then allow
the pusher to slide forward against
the nail strip.
3. Position a flooring strip and tap it
into place with the metal side of the
included hammer.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
NOTICE
DO NOT use the nailer to position the
flooring strip. Doing so will damage
the nailer and possibly the flooring
strip.
Never hit the whack cap of the nailer
multiple times to drive the nail
into the wood. If necessary, use a
hammer and nail punch to drive the
nail in. Failure to heed this warning
could cause a nail jam or a ricochet,
and serious personal injury.
Note: If you are using pre-finished
flooring material, test the nailer on a
sample strip. If the nailer base plate
is damaging or marring the flooring
surface, replace it with a new one.
7. Check the nail for satisfactory
penetration.
4. Place the nailer on the flooring strip,
as shown in Figure 3.
— If the nail depth is satisfactory,
proceed with your project.
— If the nail depth is too shallow,
slightly increase the air pressure.
— If the nail depth is too deep,
slightly decrease the air pressure.
Note: Nailing penetration is not
always consistent due to variations in
the flooring material. If necessary,
use a hammer and nail punch to
finish seating the nail.
Figure 3. Positioning nailer on flooring
strip and operating.
Clearing Jammed Nails
A jammed nail must be cleared before
using the nailer again.
DO NOT place your hands near the
nail point of entry. A nail can deflect
and tear through the surface of the
workpiece, puncturing your hand or
fingers.
To clear a jammed nail from the dis-
charge area, do these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
5. Make sure the cleat on the nailer
base plate is lined up with the edge
of the groove on the flooring strip.
2. Pull the magazine pusher all the way
back and remove the nail stick.
6. Using the rubber end of the included
hammer, hit the whack cap of the
nailer ONCE with a light to medium
force to shoot a nail into the wood.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
3. The jammed nail should be visible in
7. Throw the damaged nail away and
insert a new nail stick that only
contains clean, undamaged nails. DO
NOT use dirty or damaged nails!
the discharge area.
— If the jammed nail can be removed
with needle nose pliers, do so and
continue to Step 7.
Replacing Pistons/
O-Rings
Under heavy use, the piston or O-rings
may wear out. Replacement is quick and
easy. Contact your authorized Shop Fox
dealer to obtain the Piston Repair Kit
(Part Number X1783068) or Complete O-
Ring Kit (Part Number X1783070).
— If you cannot remove the jammed
nail, then continue with Step 4.
4. Use the 4mm hex wrench and remove
the four cap screws and lock washers
that secure the magazine to the
nailer (see Figure 4).
Note: It may be necessary to remove
the base plate to pull the magazine
out.
To replace the piston and O-rings, do
these steps:
1. DISCONNECT NAILER FROM THE AIR
SUPPLY!
2. Remove all the nails from the
magazine.
3. Use the 4mm hex wrench and remove
the four cap screws and lock washers
that secure the magazine to the
nailer (see Figure 4).
Figure 4. Location of cap screws securing
Note: It may be necessary to remove
the base plate to pull the magazine
out.
the magazine to the nailer.
5. Remove the jammed nail from inside
the discharge area with a pair of
need nose pliers (see Figure 5).
Always disconnect nailer from air
whenever servicing! During main-
tenance, a nailer connected to air
may fire accidentally, causing seri-
ous personal injury!
Figure 5. Jammed nail in discharge area.
6. Re-install the magazine.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
4. Use a 5mm hex wrench to remove the
four cap screws that secure the base
to the nailer body (see Figure 6).
7. Remove the four cap screws and lock
washers from the cylinder cover, and
remove it from the nailer body.
8. Remove the three cap screws from
the top of the plunger (see Figure 9).
Plunger
Figure 6. Cap screws that secure the
base to the nailer body.
Cap Screw
5. Carefully slide the base from the
nailer body, and remove the large
base washer and rubber bumper (see
Figure 7).
Figure 9. Plunger and cap screws.
9. From the bottom of the nailer, pull
out the piston assembly.
10. Push the piston into the sealing
sleeve and remove the sealing cap
from the top of the piston.
Washer
11. Pull the piston from the sleeve (see
Figure 10).
Bumper
Figure 7. Washer and rubber bumper.
6. Use a flat head screwdriver to pry off
the whack cap (see Figure 8).
Sealing Sleeve
Piston
Whack Cap
Cylinder
Cover
Figure 10. Piston assembly.
12. Apply a thin film of tool oil to the
new O-rings before installing them to
seat them properly on the parts.
Exhaust
Port
13. Reverse the steps above to
reassembly the nailer with the new
piston.
Figure 8. Whack cap and cylinder cover.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
CLEANING & LUBRICATION
Cleaning
Use a good solvent to clean the nose
assembly of the nailer. Always be sure
that the nailer is dry before using it
again.
Lubricating
Place two to six drops of pneumatic tool
oil in the nailer air inlet (as shown in
Figure 11) every 2 hours of continuous
use. Wipe off any excess oil near the
nailer exhaust to avoid dust build-up.
Do not allow dust, chips, sand, etc.
into the air connectors or into the body
of the nailer; this may result in leaks
and damage to the nailer and the air
couplings.
Another option to manual oiling would be
to simply install a lubricator in your air
compressor line. If your air compressor
line already has a lubricator, then regular
lubrication of your nailer will not be
necessary. Just make sure there is always
oil in the lubricator.
Figure 11. Lubricating nailer via air inlet.
Never clean this tool with gasoline
or other flammable liquids. Vapors
in the tool may ignite, causing
the tool to explode. Ignoring
this warning may lead to serious
personal injury or even death!
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
PARTS BREAKDOWN
35
37
33
31
27
38
30
29
28
32
63
24
39
25
43
41
64
42
19
26
40
23
22
38
37
44
52
18
45
51
53
17
46
15
14
44
16
54
55
47
48
49
13
12
11
26
10
50
34
5
9
60
8
4
65
56
57
3
61
59
58
7
62
69
1
6
68
70
67
66
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
PARTS LIST
REFPART #
DESCRIPTION
X1783001 CYLINDER
X1783003 BUMPER
REFPART #
DESCRIPTION
FLAT WASHER 8MM
1
3
4
5
6
7
8
9
38 XPW01M
39 X1783039 L-BOLT
40 X1783040 STOPPER
41 XPS38M
XPORP050 O-RING 49.7 X 3.5 P50
X1783005 DRIVER
PHLP HD SCR M4-.7 X 10
XPRP07M
XPSS31M
X1783008 PISTON POLE
X1783009 PISTON HEAD
ROLL PIN 6 X 20
SET SCREW M5-.8 X 8
42 X1783042 MAGAZINE SEAT
43 X1783043 MAGAZINE END CAP
44 XPLN01M
45 X1783045 PUSHER SEAT
46 XPRP42M ROLL PIN 3 X 20
47 X1783047 FLAT COIL SPRING
48 X1783048 SPRING BUSHING
49 X1783049 COMPRESSION SPRING
50 X1783050 PUSHER
LOCK NUT M4-.7
10 XPORP012-5O-RING 12.3 X 2.4 P12.5
11 X1783011 O-RING 32 X 4.5
12 X1783012 SEALING SLEEVE
13 X1783013 O-RING 12.8 X 1.8
14 X1783014 SEALING CAP
15 X1783015 O-RING 15.6 X 1.8
16 X1783016 GUN BODY
51 XPS07M
52 X1783052 MAGAZINE
PHLP HD SCR M4-.7 X 8
17 X1783017 HANDLE GASKET
18 X1783018 END CAP
53 X1783053 NAIL GUIDE
54 X1783054 NAIL GUIDE COVER
55 X1783055 DISCHARGE BRACKET
56 XPCAP95M CAP SCREW M5-.8 X 30
57 X1783057 BASE PLATE 1/2" FLOORING
58 XPCAP95M CAP SCREW M5-.8 X 30
59 X1783059 RUBBER BUTTON
60 X1783060 BASE
19 XPCAP39M CAP SCREW M4-.7 X 20
22 X1783022 CYLINDER GASKET
23 X1783023 SLEEVE GASKET
24 XPORP046 O-RING 45.7 X 3.5 P46
25 X1783025 PISTON SEAT
26 XPLW02M LOCK WASHER 4MM
27 XPCAP16M CAP SCREW M4-.7 X 16
61 XPW02M
FLAT WASHER 5MM
28 XPS56M
29 X1783029 EXHAUST COVER
30 X1783030 CYLINDER COVER
31 XPSB53M
32 XPORP025 O-RING 24.7 X 3.5 P25
33 X1783033 WHACK CAP
34 XPW02M
35 X1783035 HANDLE
37 XPLN04M LOCK NUT M8-1.25
PHLP HD SCR M4-.7 X 16
62 XPFH03M FLAT HD SCR M6-1 X 40
63 X1783063 MALLET
64 X1783064 AIR PLUG 1/4 NPT
65 X1783065 SAFETY GOGGLES
66 XPAW03M HEX WRENCH 3MM
67 XPAW04M HEX WRENCH 4MM
68 X1783068 PISTON REPAIR KIT
69 X1783069 BASE PLATE 3/4" FLOORING
70 X1783070 COMPLETE O-RING KIT
CAP SCREW M5-.8 X 18
FLAT WASHER 5MM
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1783 (Mfg. Since 2/07)
Troubleshooting
Symptom
Possible Cause
Possible Solution
1. O-rings must be replaced &
operation checked.
Air leaking at
1. O-rings in plunger/cylinder
housing are damaged.
whack cap area.
Air leaking between 1. Loose screws in housing.
1. Tighten screws.
2. Replace O-ring
3. Tighten air fitting & use
teflon tape.
housing and hose
2. Damaged O-ring.
3. Loose air fitting.
Air leaking between 1. Damaged seal.
housing and cap.
1. Replace damaged seals.
Tool skips nails
while discharging.
1. Excessive air pressure.
2. Air leaks.
3. Dirt in nose.
1. Reduce air pressure to tool.
2. Tighten screws and fittings.
3. Clean nose.
4. Dirt or damage prevents nails 4. Clean magazine and
from moving freely.
5. Inadequate air flow to tool.
inspect/repair damage.
5. Check fittings, hose,
compressor, and air
pressure.
6. Worn piston O-ring or lack of
lubrication.
6. Replace O-ring and
lubricate.
7. Damaged plunger/cylinder O- 7. Replace plunger/cylinder
rings.
O-rings.
8. Worn bumper.
9. Cap seal leaking.
8. Replace bumper.
9. Replace cap seal.
Tool runs slowly or 1. Undersized air hose.
has a loss of power. 2. Nailer is not lubricated.
1. Use a larger hose.
2. Lubricate nailer.
3. Broken spring in cap assembly. 3. Replace spring.
4. Exhaust ports on cylinder cap 4. Clean or replace damaged
are blocked.
internal parts.
Fasteners
1. Nails are the wrong size.
1. Use correct nails.
2. Use undamaged, clean
nails.
frequently jam the 2. Nails are bent or dirty.
nailer.
3. Magazine or nose screws are
loose.
3. Tighten magazine.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or damaged
parts.
5. Nails are wrong angle.
5. Use correct angle nails.
Nailer does not
fire.
1. Nailer is not lubricated.
1. Follow lubricating
instructions.
2. Nail is jammed in magazine or 2. Clear nailer magazine or
discharge area.
3. Piston shaft is damaged.
4. Air pressure too low.
discharge area.
3. Replace piston shaft.
4. Check/increase air
pressure.
Air blows out of
exhaust cap; nailer
will not fire.
1. O-ring slipped out of groove or 1. Reinstall/replace suspect
damaged inside nailer.
O-ring; turn down air
pressure.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email___________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
Advertisement
_____ Friend
_____ Website
____ Local Store
____ Other:
Mail Order Catalog
2. How long have you been a woodworker/metalworker?
0-2 Years _____ 2-8 Years _____8-20 Years
_____20+ Years
3. How many of your machines or tools are Shop Fox?
0-2 _____ 3-5 _____6-9
_____10+
4. Do you think your machine represents a good value?
5. Would you recommend Shop Fox products to a friend?
6. What is your age group?
_____ Yes
_____ Yes
____ No
____ No
20-29
50-59
_____ 30-39
_____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
$20,000-$29,000
$50,000-$59,000
_____ $30,000-$39,000
_____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOx 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|