MODELꢀ
W1669ꢀandꢀW1670
RADIALꢀDRILLꢀPRESS
INSTRUCTIONꢀMANUAL
Phone:ꢀ1-360-734-3482ꢀꢀ•ꢀꢀOn-LineꢀTechnicalꢀSupport:ꢀ[email protected]
COPYRIGHTꢀ©ꢀDECEMBERꢀ2003ꢀBYꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.ꢀREVISEDꢀOCTOBER,ꢀ2008.
WARNING:ꢀNOꢀPORTIONꢀOFꢀTHISꢀMANUALꢀMAYꢀBEꢀREPRODUCEDꢀINꢀANYꢀSHAPEꢀORꢀFORMꢀWITHOUT
#6218CR
THEꢀWRITTENꢀAPPROVALꢀOFꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.
PrintedꢀinꢀChina
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION............................................................................................. 2
About the W1669 and W1670 Radial Drill Presses.........................................................2
Woodstock Technical Support.................................................................................2
SAFETY....................................................................................................... 4
Standard Safety Instructions..................................................................................4
Additional Safety Instructions for Drill Presses ............................................................5
Avoiding Potential Injuries ....................................................................................6
ELECTRICAL................................................................................................. 7
110V Operation .................................................................................................7
Extension Cords.................................................................................................7
Grounding........................................................................................................7
ASSEMBLY.................................................................................................... 8
Base and Column ...............................................................................................9
Table Support ................................................................................................. 10
Headstock...................................................................................................... 12
Drill Chuck and ............................................................................................... 13
Spindle ......................................................................................................... 13
ADJUSTMENTS.............................................................................................14
Belt Tension ................................................................................................... 14
Feed Shaft Spring Tension................................................................................... 15
Quill-Shaft Screw ............................................................................................. 16
Table............................................................................................................ 17
OPERATIONS...............................................................................................18
Test Run........................................................................................................ 18
Headstock...................................................................................................... 19
Changing Drill Bits............................................................................................ 20
Speed Changes ................................................................................................ 21
Drill Press RPM Chart......................................................................................... 22
Drilling Depth ................................................................................................. 22
Drill, Cutter, and Hole Saw Suggested RPM Chart.................................................. 23
MAINTENANCE.............................................................................................25
General......................................................................................................... 25
Table and Base................................................................................................ 25
Lubrication .................................................................................................... 25
Troubleshooting............................................................................................... 26
W1669 and W1670 Drill Press 110V Wiring ............................................................... 27
W1669 and W1670 Parts..................................................................................... 28
W1669 Parts ................................................................................................... 30
W1670 Parts ................................................................................................... 32
Accessories .................................................................................................... 34
Notes ........................................................................................................... 36
Warranty ....................................................................................................... 38
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
About.the.W1669.and.W1670.Radial.Drill.Presses
The SHOP FOX® Model W1669 and W1670 Radial Drill Presses have been specially designed by
Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail,
ruggedly built parts and a rigid quality control program assure safe and reliable operation.
The Model W1669 and W1670 Radial Drill Presses are capable of a wide variety of drilling and sanding
operations. Purchasing the D2677 Drum Sander Set and D2722 Mandrel allows you to sand small or finely
detailed pieces. The tilting table and headstock allows surfaces to be sanded and drilled at many different
angles. The Model W1669 and W1670 is packaged with a drill chuck, motor and paddle switch with remov-
able safety key.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and dura-
bility of this product be included.
Woodstock.Technical.Support
We stand behind our machines! In the event that questions arise about your machine, parts are miss-
ing, or a defect is found, please contact Woodstock International Technical Support at 1-360-734-3482 or
send e-mail to: tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot prob-
lems and send out parts for warranty claims.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock.International,.Inc.
Attn:.Technical.Support.Department
P.O..Box.2309
Bellingham,.WA.98227
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Motor Type: ...................................................... TEFC Capacitor Start Induction
Motor:.............................................. 1⁄2 HP, 110V, 5 Amp., Single-Phase ⁄ 60 Hz
RPM: .............................................................................................. 1725
Power Transfer: ........................................................................ V-Belt Drive
Bearings: ................................................... Shielded & Lubricated Ball Bearings
Switch: ............................................ Toggle ON/OFF Switch, w/ Safety Lock Key
Spindle Travel: .................................................................................3-1⁄4''
Maximum Distance, Spindle to Base: .........................W1669 = 15-1⁄2,'' W1670 = 49''
Maximum Distance, Spindle to Table: .................... W1669 = 9-1⁄4,'' W1670 = 31-1⁄2''
Overall Height:..............................................W1669 = 31-1⁄2,'' W1670 = 64-1⁄2''
Head Tilt: .......................................................................45° Left, 90° Right
Table Tilt: ....................................................................... 90° Left and Right
Table Rotation:.................................................................................. 360°
Spindle Taper: ...................................................................................JT-33
Swing:............................................................................................... 34''
Chuck Size: ..........................................................5⁄8'' (1-13mm JT-33), Keyed
Speeds: ........................................................................... 5, Belt Controlled
Range of Speeds: ...................................................550, 880, 1570, 2490, 3470 RPM
Drilling Capacity: ..........................................................1⁄2'' Diameter in Steel
Approximate Shipping Weight:.......................... W1669 = 100 lbs., W1670 = 150 lbs.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ.MANUAL.BEFORE.OPERATING.MACHINE
FAILURE.TO.FOLLOW.INSTRUCTIONS.BELOW.WILL.
RESULT.IN.PERSONAL.INJURY
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury and damage to the machine. It may
also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
Standard.Safety.Instructions
1.. Thoroughly.read.the.instruction.manual.before.operating.your.machine..Learn the applications,
limitations and potential hazards of this machine. Keep manual in a safe, convenient place for
future reference.
2. Keep.work.area.clean.and.well.lighted..Clutter and inadequate lighting invite potential hazards.
3. Ground.all.tools..If a machine is equipped with a three-prong plug, it must be plugged into a
three-hole electrical outlet or grounded extension cord. If using an adapter to aid in accommodat-
ing a two-hole receptacle, ground the adapter using a screw to a known ground.
4. Wear.eye.protection.at.all.times..Use safety goggles with side shields or safety goggles, meeting
the national safety standards, while operating this machine.
5. Avoid.dangerous.environments..DO.NOT operate this machine in wet or open flame environ-
ments. Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure.all.guards.are.securely.in.place.and in working condition.
7. Make.sure.switch.is.in.the.“OFF”.position.before connecting power to machine.
8. Keep.work.area.clean;.free of clutter, grease, etc.
9. Keep.children.and.visitors.away..All visitors should be kept at a safe distance away while operat-
ing unit.
10. Childproof.your.workshop.with padlocks, master switches, or by removing starter keys.
11. Disconnect.the.machine.when.cleaning,.adjusting,.or.servicing.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
12. DO.NOT.force.the.tool..The machine will do a safer and better job at the rate for which it was
designed.
13. Use.correct.tool..DO.NOT force machine or attachment to do a job for which it was not designed.
14. Wear.proper.apparel..DO.NOT wear loose clothing, neck ties, gloves, jewelry; and tie back hair.
15. Remove.adjusting.keys.and.wrenches..Before turning the machine on, make it a habit to check that
all adjusting keys and wrenches have been removed.
16. Use.proper.extension.cord..When using an extension cord, make sure it is in good condition.
When extension cord is 100 feet and less in length, use those that are rated Standard Service
(grade S) or better, and that have a conductor size of 16 AWG. A drop in line voltage, loss of
power and overheating can result when using an undersized cord. The extension cord should have a
ground wire and ground plug pin, as well.
17. Keep.proper.footing.and.balance at all times.
18. DO.NOT.leave.machine.unattended..Wait until it comes to a complete stop before leaving the area.
19. Perform.machine.maintenance.and.care..Follow lubrication and accessory attachment instruc-
tions in the manual.
20. Keep.machine.away.from.open.flame..Operating machines near pilot lights and/or open flames
creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause
an explosion. DO.NOT operate the machine in high risk areas, including but not limited to, those
mentioned above.
Additional.Safety.Instructions.for.Drill.Presses
1.. DRILL.PRESS.SPEEDS..Always operate your drill press at speeds that are appropriate for the drill
bit size and the material that you are drilling.
2.. DRILLING.HOLES. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and
clear the chips with a brush after you have turned the machine off.
3.. USING.THE.CORRECT.DRILL.BITS. Use only round, hex or triangular shank drill bits, and make sure
the drill bit you are using is tightened properly..
4.. SAFE.MAINTENANCE. Never do maintenance or change speeds with this machine plugged in.
5.. USING.SERVICEABLE.TOOLS. Never use tools that are in poor condition. Cutting tools that are dull
or damaged are difficult to control and may cause serious injury.
6.. DRILLING.OPERATIONS. Never hold a workpiece by hand while drilling, never drill sheet metal
unless it is clamped securely to the table, and always secure the workpiece to the table before
drilling.
7.. SECURING.A.WORKPIECE. Properly position workpieces to avoid drilling into the table.
8.. PROTECTING.YOUR.EYES. A face guard used or safety goggles is recommended.
9.. WORKING.HABITS. Habits – good and bad – are hard to break. Develop good habits in your shop and
safety will become second-nature to you.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoiding.Potential.Injuries
Figure.2. Keep fingers away from spinning
drill bits, cutters, and sanding surfaces.
Figure.1..Never drill while holding the
workpiece by hand.
Figure.3. Remove switch safety key when not
in use.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
110V.Operation
The SHOP FOX® W1669 and W1670 Radial Drill
Presses operate at 110 volts only. The motor
supplied with your new drill press is rated at
1⁄2 HP and will draw approximately 5 amps.
When choosing an outlet for this machine, con-
sider using one with a 15 amp circuit breaker
or fuse. Keep in mind that a circuit being used
by other machines or tools at the same time
will add to the electrical load being applied by
the drill press. Add up the load ratings of all
machines on the circuit. If this number exceeds
the rating of the circuit breaker or fuse, use a
different outlet.
Any. electrical. outlet. and.
circuit. that. you. plug. your.
machine. into. must. be.
grounded.. Serious. injury.
and/or.fire.may.occur.if.this.
warning.is.ignored!
DO.NOT modify an existing low-amperage
circuit by only replacing the circuit breaker
with a breaker rated for a higher amperage.
The breaker and the complete circuit must be
replaced by a qualified electrician.
Extension.Cords
If you must use an extension cord, use the guide-
lines below to determine the correct cord length
and gauge. If you use an undersized-gauge exten-
sion cord or one that is too long, heat will gener-
ate in the cord and fire or circuit damage may
result.
Figure.4..Never remove a grounding pin.
•Use.a.cord.rated.for.Standard.Service.(Grade.S)
•Use.a.cord.that.is.16.gauge.and.100.feet.or.........
..less
•Use.a.cord.with.a.ground.wire.and.pin
•Use.only.undamaged.cords
Grounding
Ground.this.machine! The electrical cord sup-
plied with the W1669 and W1670 Radial Drill
Press comes with a grounding pin. DO.NOT
remove the pin if your outlet does not accept a
ground pin, see Figure.4. Have the outlet box
replaced by a qualified electrician or have an
appropriate adapter installed.
Remember, an adapter with a grounding wire
does not guarantee the machine will be ground-
ed. A ground source must always be verified in
the electrical circuit within the wall or conduit.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY.
Use the list below and Figure.5 to inventory your shipment before beginning assembly. If any parts
are missing, call Woodstock International, Inc. at 360-734-3482 or [email protected].
While the main components of the SHOP FOX® W1669 and W1670 Drill Presses are assembled at the fac-
tory, some assembly is required. The following order of procedures is the recommended sequence.
EYE.HAZARD!
.SUFFOCATION.HAZARD!
Immediately..discard.all.plastic.
bags.and.packing.materials.to.
eliminate. a. suffocation. haz-
ard.for.children.and.animals.
Wear. safety. goggles. during.
all. assembly. procedures..
Otherwise. serious. personal.
injury.may.occur!
Use the parts list at the back of
this manual when ordering parts.
A
C
G
J
M
H
F
D
S
Q
E
T
N
B
R
L
O
K
I
Figure.5..Component inventory.
I.. Column Bolts (4)
J.. Belt Cover Knob and Screw
K.. Lift Handle Crank
L.. Pinion Gear
R.. W1670: Table Support Arm
Bracket
A.. Headstock Assembly
B.. Base
S.. W1670: Hex Wrenches, 3MM
C.. Column
and 5mm
D.. Table
M.. Lock Handles (4)
N.. Rack
T.. Mounting Hardware
(Refer to the parts list on
Page.30.for details)
E.. Table Bracket Assembly
F.. Drill Chuck and Key
G.. Spindle Handles and Knobs (3)
H.. W1669: Hex Wrenches 3MM,
5MM, 10MM
O.. Column Ring
P.. Open End Wrench (Not shown)
Q..W1670: Lock Lever
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Base.and.Column
For maximum stability, secure the W1670
floor-model drill press to a sturdy surface like
3
a floor or a 4' x 4' x ⁄4" piece of plywood. For
TIPPING.HAZARD!
the W1669 bench-model, secure it to a sturdy
Never.mount.a.drill.press.to.a.
mobile. base.. Mount. the. drill.
press.base.to.a.sturdy.surface.
or.the.drill.press.may.tip.and.
cause.injury..
workbench or tool table.
1.. UNPLUG.THE.MACHINE!
.
•. If.installing.the.W1670.to.a.concrete..
. floor,.do.these.steps:
.
a. Position the drill press in a sensible work
area where the base sits flat at all four
corners, or the base may crack when you
tighten the fasteners.
b. Mark and drill the floor, and install the
concrete anchor bolts (not included) (see
Figure.6).
c. Position the base and fasten the base to
the floor carefully as not to crack it.
. . •. If.installing.the.W1670.to.a.plywood.. .
. . base,..do.these.steps:
Figure.6..Secure base to floor.
a. Center the drill press base along the back
3
edge of the 4' x 4' x ⁄4" sheet of plywood
(see Figure.7).
b. At each corner of the drill press base, drill
the plywood.
c. Secure the base to the plywood with four
3/8" diameter bolts, washers, and nuts
(not included).
. . .
. .
•..If.installing.the.W1669.to.a.tool.table...
....or.workbench,.do.these.steps:
3
Figure.7..Secure base to 4' x 4' x ⁄4" plywood.
a. Position the base on a bench or tool table
capable of supporting approximately 100
lbs.
b. Drill two mounting holes (Figure.8), and
secure the base to the table with the two
supplied carriage bolts and wing nuts.
Mounting
Holes
2.. Place the column on the base, and install the
four column bolts supplied.
Figure.8..Workbench mounting holes.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table.Support
The W1669 comes with a one geared table
bracket. The W1670 comes with a geared table
bracket and table support arm, which allows
the distance between the column and table to
be adjusted. No table support parts are inter-
changeable between the two drill presses.
Pinion
Gear
Worm
Gear
To.install.the.table.support.assembly,.do.
these.steps:
. Insert the table lock lever through the un-
1.
threaded hole (see Figure.9
table
) in the
bracket, and then tighten the lever into
the threaded side exactly three turns.
Un-threaded Hole
Starting with the pinion gear, insert the
shaft into the table bracket and mesh the
teeth with the worm gear as shown in
Figure.9..
2..
Figure.9..Pinion and worm gear installation.
Flat
Pad
Align the set screw in the crank handle
with the flat pad on pinion shaft.
3..
4..
Tighten the 3mm set screw to lock the
handle in place (see
Figure.10).
Set Screw
. Examine the rack and note that the rack
teeth at one end are cut closer to the end
of the rack than the other.
5.
Insert the rack through the table bracket
so the end that has the rack teeth cut clos-
er to the end is pointing down (see Figure.
11).
6.
Figure.10..Align set screw with flat pad on
pinion.
Hold the rack against the worm gear and
slide the table bracket and rack onto the
7.
column (see
11).
Figure.
Figure.11..Installing rack and table bracket.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Seat the rack tapered-point into the bevel
that is cut into the column support tube
(see Figure.12).
Tapered Rack
Point and
Column Support
Tube Bevel.
Slide the column ring onto the column with
the inside bevel in the down position until
the rack tapered-point seats into the bevel
(see Figure.13).
9.
Position the column ring so the table
bracket and rack can just rotate around
the column without binding.
10.
11. Carefully, snug the set screw to hold the
column ring in place. Over-tightening the
column ring will distort or split the column
ring.
Figure.12..Bevel and rack seated correctly.
Set
Column Ring
Screw
Bevel
Figure.13..Column ring in the correct position.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Headstock
The headstock is secured with a set screw so it
is aligned with the drill press base for balance
and weight distribution. DO.NOT over tighten
the set screw, or you will bend the column or
strip the threads.
Locking
Gib
GET.help.to.lift.the.head-
stock,. or. you. may. seri-
ously. hurt. your. back. or.
drop.the.headstock..
To.install.the.headstock.assembly,.do.these.
steps:
Figure.14..Locking gib installation.
1.. Place the locking gib into the recessed
pocket on the inside of the column bracket
casting (see Figure.14).
2. With an assistant, lift and position the
headstock pocket over the column and
allow the headstock to slide down until
the column fully seats into the headstock
(approximately 2", see Figure.15).
3.. Rotate the headstock directly over the foot
of the base as viewed from the front of the
drill press.
4. Screw in the two lock handles on the sides
Figure.15. Headstock-to-column installation.
of the headstock.
5. Using a plumb bob and ruler, center the
headstock with the base, and tighten the
two set screws to secure the headstock to
the column (see Figure.16).
Figure.16..Aligning the headstock.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill.Chuck.and.
Spindle
Your keyed drill chuck attaches to the drill
spindle. When properly joined, the JT-33
tapers on the spindle and inside the chuck cre-
ate an almost permanent connection.
To.install.the.drill.chuck,.do.these.steps:
1... Clean the drill chuck and spindle with min-
eral spirits and follow all safety warnings
on the container (see Figure.17).
Note: Failure to clean the tapered mating
surfaces of the spindle and drill chuck may
result in a loose or wobbly chuck.
2. Use the provided chuck key to adjust the
jaws of the chuck until they are inside of
the drill chuck body (see Figure.18).
Figure.17..Clean the chuck before installation.
3. Place the drill chuck on the spindle and tap
the chuck onto the spindle with a block of
wood or a dead-blow hammer (see Figure.
18). DO.NOT.use a metal hammer to seat
the drill chuck onto the spindle!
Chuck Jaws
Recessed and
Protected
Inside of
Chuck
Figure.18..Seating chuck into spindle.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Belt.Tension
During the life of your drill press you will use differ-
ent belt and pulley combinations. No matter which
pulley combination you use, make sure that the belt
is tensioned properly
UNPLUG. the. drill. press.
before. any. assembly,.
adjustment,. maintenance,.
or. belt. changing. proce-
dures.. Otherwise. serious.
personal.injury.may.occur!
To.adjust.the.drive.belt.tension,.do.these.
steps:
Figure.19..Open belt safety cover.
1... UNPLUG.THE.DRILL.PRESS!.
2... Open the belt safety cover (see Figure.
19).
3.. Loosen both motor lock knobs at the side
of the headstock (see Figure.).
Push rod
4... Slide the motor away from the headstock
until the belt is taut.
5... Hold the motor in position, and tighten the
lock screw, and make sure the belt deflec-
tion gap is correct when pinched together
between the pulleys (see Figure.21).
Motor
Lock Knob
Figure.20..Motor lock knob.
• If the gap between both inner sides of
the belt is greater or less than 3⁄4" repeat
Steps.3-5 until the deflection gap is 3⁄4".
• If the deflection gap is 3⁄4" the belt is ten-
sioned correctly.
6... Close the belt safety cover.
Belt Deflection
gap should be
about 3⁄4
"
Figure.21..Measuring belt deflection.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed.Shaft.Spring.
Tension
The feed shaft return spring is adjusted at the fac-
tory; however, during the life of the drill press you
may want to adjust the feed shaft return spring to
a greater tension for a stronger quill return.
Locking Lug
Jam Nut
and
Cover Nut
WEAR. safety. goggles. and.
gloves.when.adjusting.the.
feed. shaft. spring.. Serious.
injury. may. occur. if. this.
warning.is.ignored!
Spring
Lock Cover
To.adjust.the.feed.shaft.spring.tension,.do.
these.steps:
Figure.22..
Feed shaft return spring assembly.
1... UNPLUG.THE.DRILL.PRESS!
Locking Lug
2... Wipe off any oil on the spring-lock cover so
it will not slip when you hold the cover from
spinning (see Figure.22).
3... Make sure the quill is completely seated and
the depth stop reads zero.
4.. Put on thick leather gloves, and hold the
spring cover against the side of the head-
stock so the cover stays splined with the
locking lug; remove the jam nut and loosen
the cover nut approximately 1⁄4" (6.4mm).
Spring-Cover
Lock Slot
5... Pull the cover outward just enough to dis-
engage the spring-cover lock slot from the
locking lug (see Figure.23).
Figure.23. Typical spring cover lock slot and
locking lug.
6... Rotate the cover counterclockwise to
increase spring tension, or let the cover
slowly unwind in the clockwise direction to
reduce spring tension (see Figure.23).
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
7... Engage the next available spring-cover
lock slot with the locking lug and hold the
spring lock cover tightly against the side of
the headstock (see Figure.24).
Lock Lug
Cover Nut
8... Snug the cover nut against the spring cover
just until the nut stops, and then back-
off the nut approximately 1⁄3 turn, or just
enough so there is no binding anywhere
along spindle travel path.
9... Hold the cover nut and tighten the jam nut
against the cover nut.
Quill-Shaft.Screw
Figure.24..Hold the spring cover tightly.
While you may never have to adjust the quill-
shaft screw, you should understand its func-
tion and know how to adjust it should you ever
need to remove the quill for cleaning. This
screw prevents the quill from rotating during
drilling and sanding procedures, and if adjusted
incorrectly, the quill may have lash or bind.
To.adjust.the.quill-shaft.screw,.do.these.steps:
1. UNPLUG.THE.DRILL.PRESS!.
2... Clean and lubricate the quill shaft with a
thin coat of light oil, so the quill travels
freely (see Figure.25).
3... Loosen the jam nut (see Figure.26).
Figure.25..Clean and oil quill shaft.
4... Move the quill up and down through the
entire range of travel, and turn the quill-
shaft screw inward as far as it can go with-
out binding the quill.
5... Tighten the jam nut, and check the quill
movement for binding or play while moving
the quill up and down through its entire
range of travel.
Jam
Nut
6... Re-adjust the quill-shaft screw as required.
Quill-Shaft
Screw
Figure.26..Quill-shaft screw and jam nut.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table
The table can be adjusted for height, rotation,
and angle. The W1670 adds the fourth adjust-
ment of table distance from column.
Note: Table or table support parts are not
interchangeable between the W1669 and the
W1670 drill presses (see Figures.27.and.28).
To.adjust.the.table,.do.these.steps:
1... Loosen the table lock lever.
2. Turn the hand crank to raise or lower the
table.
3. Tighten the table lock lever.
Figure.27..W1669 Table support assembly.
4. For the W1670, loosen the table tilt lock
bolt (see Figure.29); or for the W1669,
loosen the cap screw.
5. Turn the index pin draw nut clockwise and
draw the index pin out of the casting until
you can rotate the table to your desired
angle (see Figure.29).
Note: Use this index pin only for indexing
the table to the “Zero degree” position.
Note: To index the table back to the zero
position, back off the draw nut, turn the
table to zero, tap the index pin back into
the casting, and tighten the table tilt lock
bolt.
Figure.28..W1670 Table support assembly.
6. Tighten the tilt table lock bolt or cap
Table-Tilt
Lock Bolt
(W1670)
or
screw, and double check your angle.
Table-Tilt
Lock Cap
Screw
(W1669)
Index Pin
Tilt
Scale
and
Draw Nut
Figure.29..Tilt mechanism and lock bolt.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Test.Run
This drill press will perform many types of oper-
ations that are beyond the scope of this manual.
Many of these operations can be dangerous or
deadly if performed incorrectly.
WEAR.safety.goggles.and.
a.respirator.during.drill-
ing. or. sanding. opera-
tions.. Otherwise. seri-
ous.personal.injury.may.
occur!
The instructions in this section are written with
the understanding that the operator has the
necessary knowledge and skills to operate this
machine. If at any time you are experiencing
difficulties performing any operation, stop using
the machine!
If you are an inexperienced operator, we
strongly recommend that you read books, trade
articles, or seek training from an experienced
lathe operator before performing any unfamiliar
operations. Above all, your safety should come
first!
Keep. your. shop. “Child.
Safe.”. Always. remove.
the. switch. safety. key.
when.drill.press.is.not.in.
use.. Serious. injury. may.
occur.
To.start.the.drill.press,.do.these.steps:
1. Make sure the starting switch paddle is
down for OFF.
2. Make sure all fasteners and lock handles are
tight.
3. Make sure the drill chuck key is removed.
4. Plug in the power cord.
5. Lift the ON/OFF switch to start the drill
press, and make sure that your fingers are
poised near the paddle, as shown in Figure.
30..In case there is a problem you can turn
the drill press off.
Figure.30..Fingers poised near the stop switch.
6. Observe and listen to the drill press, it
should run smoothly, with little or no vibra-
tion or rubbing noises.
• If you hear strange or unusual noises, shut
the drill press OFF, and wait for the spin-
dle to stop moving.
7. Unplug the drill press and refer to the
“Troubleshooting” table on Page.27
to help isolate and correct the problem
before using the drill press again.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Headstock
To drill wide workpieces up to 34" in diam-
eter, you can slide the headstock in and out
to increase the distance between the drill
chuck and the column up to 17". You can also
tilt the headstock from 45° clockwise to 90°
counterclockwise for drilling angled holes or for
horizontal boring machine use. Using the slide
and tilt features, you can drill a line of straight
or angled holes without the need to reposition
your workpiece after drilling each hole.
Slide
Knob
To.use.the.headstock-sliding.feature,.do.
these.steps:
Lock
Lever
1. Loosen the lock lever located on the right
side of headstock (see Figure.31).
Figure.31. Headstock tilt and slide controls.
Turn the slide knob to move the headstock
back and forth to desired position and then
2..
tighten the lock lever (see Figure.31).
.
Guide Pin
and Knob
To.use.the.headstock-tilting.feature,.do.
these.steps:
Note: If the scale is not calibrated, set the
table to zero degrees, zero the headstock with
the table, and then reposition the scale to zero
degrees.
Horizontal Column
1.. Loosen the lock handle on the right side of
headstock (see Figure.31).
2.. Pull out the guide pin knob located on the
left side of the headstock and rotate the
pin knob 90° so the pin stays disengaged
from the horizontal column (see Figure.
32).
Figure.32..Headstock guide pin and knob.
3.. While reading the tilt scale, tilt the head-
stock to your desired angle and tighten
lock lever (see Figure.31).
4.. Drill your workpiece.
5.. Loosen lock handle located on the right
side of headstock, and tilt the headstock
to zero and move the guide pin back into
the guide slot.
6.. Tighten the lock lever.
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing.Drill.Bits
The chuck supplied with your W1669 or W1670
drill press accepts drill bits from 1/32" to 5⁄8''.
Follow the steps below to safely swap drill bits
or sanding spindles.
TURN. OFF. and. UNPLUG.
the. drill. press,. and. wait.
until. all. working. parts.
are. stopped. before. you.
attempt. to. change. drill.
bits.. Otherwise,. severe.
injury.may.occur!
To.change.a.drill.bit.or.sanding.drum,.do.
these.steps:
Figure.33..Installing a drill bit.
1. UNPLUG.THE.DRILL.PRESS!
2.. Use the chuck key to remove the old drill
bit, and open the chuck wide enough to
accept the new bit or the sanding drum
mandrel (see Figure.33).
3.. Install the bit or mandrel so the chuck jaws
will grab as much of the bit or mandrel
shank as it can.
• If you are installing a small drill bit, make
sure it is held between three jaws instead
of only two, and NEVER allow a chuck to
grab the fluted body of drill bits.
4.. Using any of the three key locations,
tighten the chuck with the chuck key and
remove.the.key (see Figure.34).
Figure.34..Using the chuck key.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed.Changes
The Model W1669 and W1670 Radial Drill Press
has 5 speeds ranging from 550 to 3470 RPM.
To find your needed drilling speed and pulley
combination, refer to the speed chart located
under the belt guard; or go to.Page.22 and
refer to the Drill.Press.RPM.Chart.
Never.operate.drill.press.
with. belt. cover. in. the.
open.position..Your.hand.
may.become.trapped.in.a.
belt.and.serious.personal.
injury.will.occur.
UNPLUG. the. drill. press.
before. changing. speeds.
to.avoid.accidental.start.
up..Failure.to.do.this.may.
result.in.serious.personal.
injury.
Pushrod
To.change.the.drilling.speed,.do.these.steps:
1... UNPLUG.THE.DRILL.PRESS!
2.. Loosen the belt tension lock knobs on the
side of the headstock (see Figure.35).
3. Locate the desired speed on the chart and
move the V-belt to the desired V-grooves
on the motor and spindle pulleys (see
Figure.36).
Figure.35..Loosening lock knob.
4.. Push the motor inward, and move the V-
belt to the right spot.
5.. Push the motor toward the back of the
headstock. The motor support rod is spring
loaded and will follow the motor. Tighten
the lock knob when the right tension is
achieved.
6. Close the cover.
Figure.36..Adjusting belt to desired speed.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill.Press.RPM.Chart
Use Figure.37.to select the optimum motor-to-spindle pulley ratio for drilling, cutting, and sanding
operations. for example the above figure shows the belt in the C position on the spindle pulley and the
#3 position on the motor pulley, which will give a speed of 1,520 RPM. Refer to the Drill,.Cutter,.and.
Saw.RPM.Chart on Page.23 for suggested tool RPMs.
Figure.37..Drill Press RPM Chart.
Drilling.Depth
Your new drill press comes fitted with a depth
Upper
stop that allows drilling many holes at a pre-
set depth consistently. When the hex nuts are
set, the nuts will contact the stop flange and
stop the drill press from drilling any deeper.
Hex Nut
Lower.
Hex.Nut
To.adjust.the.drilling.depth,.do.these.steps:
1. Measure the maximum depth that you want
to drill a series of holes at. In this example
the maximum depth is 1 1⁄4" deep.
Stop.
Flange
2. Loosen the hex nuts shown on the depth
stop and align the lower nut to the 1 1⁄4
mark on the depth stop rod (see Figure.
38).
"
Depth.
Stop
Figure.38..Depth stop set for 11⁄4" drilling
3. Hold the lower hex nut and tighten the
upper hex nut so both nuts are locked
together.
depth.
4. Make sure the depth has been set cor-
rectly, measure, or drill a hole into scrap
wood before drilling into any workpiece.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Drill,.Cutter,.and.Hole.Saw.Suggested.RPM.Chart
.
.
.
.
.
.
.
.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Table.and.Base
General
Keep the table and other unpainted surfaces
rust-free with regular applications of prod-
ucts like Boeshield® T-9. For long term stor-
age consider products like Kleen Bore's Rust
Guardit™.
Periodic maintenance on your Model W1669 and
W1670 Radial Drill Press will ensure its opti-
mum performance. Make a habit of inspecting
your drill press after each use.
Lubrication
NEVER. adjust. or. service.
the. machine. while. it. is.
running.. Wait. until. the.
machine. is. turned. off,.
unplugged.and.all.working.
parts.have.come.to.a.stop.
before.proceeding!
Since all bearings are shielded and permanently
lubricated, simply leave them alone until they
need to be replaced. DO.NOT lubricate them.
For other items on this machine, such as the
quill, table and column, horizontal and verti-
cal columns, an occasional application of light
machine oil is all that is necessary to maintain
smooth rust-free operation.
Check.for.the.following.conditions.and.repair.
or.replace.when.necessary.
1. Loose or missing base mounting bolts.
2. Worn switch.
Before applying any lubricant, clean off the old
lubricant, and any sawdust or metal chips.
3. Worn or damaged cords and plugs.
4. Damaged drive belt.
DO.NOT over lubricate, your goal is to achieve
adequate lubrication. Too much lubrication will
attract dirt and sawdust, and various parts of
your machine could loose freedom of move-
ment.
5. Any other condition that could hamper the
safe operation of this machine.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
This section covers the most common symptoms and corrections with this type of machine.
WARNING!.DO.NOT.make.any.adjustments.until.power.is.disconnected.and.moving.parts.
have.come.to.a.complete.stop!
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1669.and.W1670.Drill.Press.110V.Wiring
ELECTROCUTION HAZARD!
Disconnect all power to the machine
and wall receptacle before doing any
electrical service. Otherwise, you
or others may be burned or
electrocuted resulting in injury or
death!
Start
Switch
Blk
Grn
Grn
5-15 Plug
Start
Capacitor
Grn
Capacitor
Cover
110V
Motor
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1669.and.W1670.
Parts
23
66
21
22
54
53
89
85
10
16A-1
77
19
79
102
81
94
93
65
53
15
64
62
20
63
33
24
103
16A
25
26
9
36
8
30
28
86
49
28A
28
27
56
76
31
11
76
32
34
32-1
19-2
19-1
36
33-1
60
59
19-3
38
75
38-1
89
46
35
50
45
19-4
19-6 19-5
51
39
37
40
35-1
48
107
47
52
41
108
105
3
2
1
0
45A-2
104
45A-1
42
107
87
43
106
45A-3
44
88
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1669,.W1670.Parts.List
.DESCRIPTION
PARTS
.REF. PART.#.
.DESCRIPTION
.REF. PART.#.
1
8
9
X1669008
XPR16M
GEAR
44
45
X1669044
X1668031
⁄2" CHUCK 1-16MM JT#33
EXT RETAINING RING 9MM
HEX NUT M8-1.25
COLLAR
DEPTH STOP ROD N/S
10
11
15
XPN03M
X1668019
X1669015
45A-1 X1668031A
CLAMP BOLT M10-1.5 X 30
KNOB BOLT M8-1.25 X 16
MOUNT PLATE N/S
45A-2 X1669045A-1 DEPTH STOP ROD BRACKET
45A-3 X1668031A-6 DEPTH STOP MOUNT
16A X1669016A
46
47
48
49
50
51
52
53
54
56
59
60
62
63
64
65
66
75
76
77
79
81
85
86
87
88
89
93
94
X1668030
X1668033
X1669048
X1669049
XPR03M
FEED SHAFT
FEED COLLAR
16A-1 X1669016A-1 MOTOR PLATE N/S
1
19
X1669019
MOTOR ⁄2 HP, 110V
HANDLE AND KNOB
DEGREE SCALE
EXT RETAINING RING 12M
BEARING 6201
POWER CORD
set screw
PHLP SCREW ⁄4"-20 X ⁄8
RIVET
19-1 X1669019-1 S. CAPCTR 150MFD/125VAC
19-2 X1669019-2 CAPACITOR COVER
19-3 X1669019-3 MOTOR FAN
XP6201
19-4 X1669019-4 FAN COVER
X1669052
X1669053
XPS07
X1669056
X1669059
XPN02
X1669062
X1669063
XPS06
X1669065
X1669066
X1669075
X1669076
XPW01M
XPW06M
XPB09M
X1669085
X1669086
XPAW03M
XPAW05M
XPHTEK7
X1669093
X1669094
19-5 XPS54M
19-6 XPW05M
PHLP HD SCR M4-.75 X 6
FLAT WASHER 4MM
PULLEY COVER
MOTOR PULLEY
V-BELT 0-1480
UNTHREADED FEMALE KNOB
LOCK PIN ASSEMBLY
SPINDLE PULLEY
DRIVE SLEEVE
INT RETAINING RING M40
BEARING 6203
1
3
"
20
21
22
23
24
25
26
27
28
X1669020
X1669021
X1669022
X1669023
X1669024
X1669025
X1669026
XPR23M
5
SPECL SET SCR ⁄16"-18 X 1"
5
HEX NUT ⁄16"-18
LABEL
WIRE STRAP
PHLP SCREW 10-24 X ⁄8
MOTOR SWITCH CORD
SPEED CHART
3
"
XP6203
SAFETY LABEL
LOCKING GIB
28A X1669028A
SPACER
30
31
32
X1669030
XPLN08
X1668024
LEVER
LOCK NUT ⁄2"-20
FLAT WASHER 8MM
FLAT WASHER 12MM
HEX BOLT M8-1.25 X 20
Safety goggles LABEL
LONG HAIR SAFETY LABEL
HEX WRENCH 3MM
1
SPRING COVER
RETURN SPRING
HORIZONTAL COLUMN
32-1 X1668025
33 X1669033
33-1 X1669033-1 HORIZONTAL COLUMN RACK
34
35
X1669034
XPSW09
HEADSTOCK
HEX WRENCH 5MM
3
SWITCH AND KEY
SWITCH KEY
SELF TAP SCREW #8 X ⁄8
RUBBER WASHER 8MM
GUIDE ROD 16 X 30MM
HEX NUT M10-1.5
"
35-1 XPSW09-1
5
36
37
38
XPSS02
XPS22
X1669038
SET SCREW ⁄16"-18 X 3⁄8
"
5
PHLP SCREW 10-24 X ⁄8
"
102 XPN02M
103 XPLW06M
104 XPW03M
105 XPS68M
106 XPN03M
107 XPN02M
108 XPSB14M
SWITCH BOX
LOCK WASHER 10MM
FLAT WASHER 6MM
38-1 X1669038-1 SWITCH MOUNTING PLATE
39
40
41
42
43
X1669039
X1669040
XP6202
X1669042
X1669043
RUBBER WASHER
QUILL SHAFT
BEARING 6202
SPINDLE JT#33
CHUCK KEY
PHLP HD SCR M6-1 X 10
HEX NUT M8-1.25
HEX NUT M10-1.5
CAP SCREW M8-1.25 X 20
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1669.Parts
80
73
13
83
11
7-2
56
71
72
70
84-1
7
74
73
11
84
7-1
91
79
99
78
4
5
3
93
Mounting
Surface
1
98
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1669.Parts.List
PARTS
.REF. PART.#.
.DESCRIPTION
.REF. PART.#.
.DESCRIPTION
1
3
X1669001
XPB09M
BASE
72
73
74
78
79
80
83
84
X1669072
XPSS01M
X1669074
XPSB77M
XPW06M
X1669080
X1669083
X1669084
LIFT HANDLE CRANK
SET SCREW M6-1.0 X 10
10T GEAR
CAP SCREW M12-1.75 X 30
FLAT WASHER 12MM
COLUMN RING
HEX BOLT M8-1.25 X 20
W1669 RACK
W1669 COLUMN
GEARED TBL BRKT N/S
4
5
7
X1669004
X1669005
X1669007
7-1
7-2
11
13
54
56
70
71
X1669007-1 COMPLETE TBL BRKT ASSY
X1669007-2 GEARED TBL BRKT SCALE
TABLE
X1668019
X1669013
XPS07
X1669056
X1669070
X1669071
LEVER BOLT M10-1.5 X 30
HORR. COLUMN BRKT
COLUMN SUPPORT ARM N/S
84-1 X1669084-1 SCALE
1
3
PHLP SCREW ⁄4"-20 X ⁄8
"
91
93
99
98
XPAW10M
X1670093
XPLW05M
XPWN02M
HEX WRENCH 10MM
HEX BOLT M8-1.25 X 125
LOCK WASHER 12MM
WING NUT M8-1.25
RIVET
PIN
WORM PINION
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
83
80
73
W1670.Parts
13
92
7-2
56
84-1
71
84A
11
70
72
73
7
74
11
97
84
96
94
95
7-1
4A
5A
101
3
93
Mounting
Surface
1
98
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1670.Parts.List
PARTS
.REF. PART.#.
.DESCRIPTION
.REF. PART.#.
.DESCRIPTION
1
3
X1670001
XPB31M
BASE
74
80
83
84
X1668015
X1668008
X1670083
WORM GEAR
COLUMN RING
TABLE
HEX BOLT M10-1.5 X 40
W1670 RACK
W1670 COLUMN
GEARED TBL BRKT N/S
4A
5A
7
X1670004A
X1670005A
X1668010A
X1668010A-1 COLUMN SUPPORT ARM N/S
84-1 X1669084-1 SCALE
84A X1670084A TABLE SUPPORT ARM
7-1
7-2
11
13
56
70
71
72
73
X1668010A-2 COMPLETE TBL BRKT ASSY
X1669007-2 SCALE
92
93
94
95
96
97
98
X1668013
X1670093
XPN01M
X1668111B
X1670096
XPW14
CLAMP BOLT M12-1.75 x 50
HEX BOLT M8-1.25 X 125
HEX NUT M6-1.0
X1668019
X1670013
X1669056
LEVER BOLT M10-1.5 X 30
HORR. COLUMN BRKT
RIVET
SPECIAL PIN
5
X1668010A-3 AXLE
HEX BOLT ⁄8"-13 X 11⁄2
"
5
X1668012
X1668016
XPSS01M
WORM PINION
LIFT HANDLE
FLAT WASHER ⁄8
WING NUT M8-1.25
SPECIAL WRENCH
"
XPWN02M
SET SCREW M6-1.0 X 10
101 X1668152
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
The following drill press accessories may be available through your local Woodstock International Inc.
Dealer. If you do not have a dealer in your area, these products are also available through online dealers.
Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at:
1-800 840-8420 or at [email protected].
Sanding.Sleeves are sized to fit the D2677 Drum Sander Set. These hard
Sanding Sleeves are available in 60, 80, 100, 120, and 150 grits. Keep
plenty of these consumable Sanding Sleeves on hand.
Sanding.Sleeves
.
.
Size
.
(Dia..x.Ht.).
60.Grit.
80.Grit
.
.
100.Grit.
120.Grit. 150.Grit
.
1".X.41⁄4". D2683. D2684. D2685. D2686. D2687
. 11⁄2".X.41⁄4". D2688. D2689. D2690. D2691. D2692
.
2".X.41⁄4". D2693. D2694. D2695. D2696. D2697
The 4".PRO-STIK® Stick with Handle is the easiest solution for increasing
the life of sanding sleeves by removing pitch and sawdust particles from
the abrasive pores, which later harden in place if not removed. Simply
press the cleaner lightly against the moving abrasive surface to remove
clogged-up pitch and sawdust. PRO-STIK® cleaners are available in other
sizes for any cleaning application that would need cleaners with handles,
as blocks, or as flat pads. (Not recommended for wide-belt sanders.)
D2677. Drum. Sander. Set includes three rubber sanding drums 41⁄4" in
length to accommodate 1", 11⁄2" and 2" diameter sanding sleeves. This kit
also includes one 80 grit sleeve for each drum to get things started.
D2722.Mandrel is a 3⁄8" shank and is required to use with the Drum Sander
Set with any drill press.
Drill. Press. Clamps adjust quickly and easily to lock your workpiece
in any position. The clamping pad pivots to conform to any workpiece,
ensuring uniform pressure.
W1301 6" Drill Press Clamp (11⁄2" Capacity)
D2192 10" Drill Press Clamp (3" Capacity)
D2493 12" Drill Press Clamp (5" Capacity)
SHOP FOX®.Drill. Press. Vises use precision ground steel guide rods,
smooth-action Acme threads, ground steel jaws, with fixed jaw
V-grooves for holding round stock, and dovetailed ways where
applicable.
D2727 SHOP FOX® (3" Basic Vise)
D2728 SHOP FOX® (4" Basic Vise)
D2729 SHOP FOX® (6" Basic Vise)
D2933 SHOP FOX® (33⁄4" Angle Vise)
D2730 SHOP FOX® (3" Cross Sliding Vise)
D2731 SHOP FOX® (4" Cross Sliding Vise)
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
The. SHOP FOX® D2056. Tool. Table is great for bench-top tools like
chop saws, drill presses, planers, scroll saws and bandsaws. Support cross
braces on top provide incredible strength and capacity. Flared legs and
adjustable rubber feet ensure stability and reduce machine vibration.
Butcher block finish table top measures 13" x 23" and is 301⁄2" tall with a
700 lb. capacity.
D2251.Steelex®..Adjustable.Circle.Cutter cuts flat-sided holes in wood
from 1" to 5". Made of M-2 alloy steel, this Circle Cutter features a 3⁄8" hex
shank, 5⁄16" drill, center point and hex wrench.
D3161.Steelex®..Heavy-Duty.Carbide-Tipped.Adjustable.Circle.Cutter.
is Carbide Tipped and cuts 13⁄4" to 53⁄4" diameter holes in the toughest
material. For use with 1⁄2" drill press chucks. Includes hex wrench and 7⁄16"
pilot drill.
Woodstock. offers. a. full. line. of. Brad. Point. Bits,Tenon/Plug.
Cutters,. Countersink. Bits,. and. Stubby. Drill. Bits to satisfy
every need. Whether for do-it-yourselfers or professional
woodworkers, you can depend on Woodstock International
Inc. to manufacture a useful selection of drilling and cutting
for a complete product line available through your dealer.
Steelex®.Carded.Forstner.Bits stack up as some of the best bits in
the world. In fact, an independent testing lab proved that the
Steelex® brand cut was equal to or better than Forstner Bits from
Austria, known for being the best. For use with drill presses. Refer
product line available through your dealer.
Steelex.Plus®.Bi-Metal.Hole.Saws stay sharper longer than carbon steel
hole saws. Equipped with high-speed steel alloy cutting teeth bonded to
a welded steel body, they cut wood, metal and plastics with ease.
D2784 10-pc. Bimetal Hole Saw Set
D2020 8-pc. Aggressive Hole Saw Set
D2783 6-pc. Bimetal Hole Saw Set
1
D2797 ⁄2" X 20 UNF Hole Saw Arbor
5
D2798 ⁄8" X 18 UNF Hole Saw Arbor
D2799 12" Hole-Saw Arbor Extension
D2928 Replacement Pilot Drill for D2797
D2929 Replacement Pilot Drill for D2798
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-
manship and materials for a period of two years from the date of original purchase by the original
owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence
or accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within
two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect resulted from
causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must
bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil-
ity standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty.Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________E-mail__________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
_____ Friend
_____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____8-20 Years
_____20+ Years
3. How many of your machines or tools are Shop Fox®?
_____ 0-2 _____ 3-5 ____6-9
_____10+
4. Do you think your machine represents a good value?
_____ Yes
____ No
____ No
5. Would you recommend Shop Fox® products to a friend? _____ Yes
6. What is your age group?
_____ 20-29
_____ 50-59
_____ 30-39
_____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
_____ $30,000-$39,000
_____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Old House Journal
____ Shotgun News
9. Comments:.__________________________________________________________________
. _____________________________________________________________________________.
. _____________________________________________________________________________.
. _____________________________________________________________________________.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK.INTERNATIONAL,.INC.
P.O..BOX.2309
BELLINGHAM,.WA..98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|