2300003 LOADER MOUNTING KIT
for LU132 & LU132-2 Loaders
on Case IH® Tractors
JX1085C, JX1095C
or New Holland® Tractors
TN85A, TN95A,
TN85DA, TN95DA
Includes Hose Kits
1018219, 1023597
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
must be surgically removed as soon as possible by
!
a doctor familiar with this form of injury or gan-
LEA EL INSTRUCTIVO!
grene, serious injury, or death will result. CON-
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, con-
cern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
INSTALLATION
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ This Loader Mounting Kit is to be used only for
the loaders and tractors specified in this manual.
Any other use or modification of this mounting kit
may result in serious injury or death.
„ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
„ After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
„ Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
„ Use a suitable lifting device of sufficient capac-
ity. Use adequate personnel to handle heavy com-
ponents.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
Loader Mounting Kit SR3 (4/25/2003)
Safety 3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADER MOUNT INSTALLATION
TRACTOR PREPARATION
NOTICE
■ Clean threaded holes in the tractor chassis thor-
oughly using a tap of the proper size. Paint, rust, or
debris in the threads may not permit cap screws to
be installed and tightened correctly.
■ Only use this mounting kit for mounting Woods
LU132 or LU132-2 loader on Case IH® JX1085C and
For installing this mounting kit, references to right, left,
forward, and rearward directions are determined from
the operator’s position in the tractor seat.
JX1095C or New Holland® TN85A, TN95A, TN85DA,
TN95DA tractors. Any other use or modification of
this mounting kit may result in serious injury or
death.
1. Shut off engine and set parking brake during instal-
lation.
NOTICE
2. Remove the tractor front weights if equipped.
■ This equipment must be assembled and
installed on the customer’s tractor by the Woods
dealer. Dealer must thoroughly inspect equipment
and complete each item on the PRE-DELIVERY
CHECK LIST, DELIVERY CHECK LIST, and PROD-
UCT REGISTRATION from the loader manual
before equipment is released to the customer.
3. Leave mounting hardware loose until loader
mounts are completely installed.
Remove Exhaust Bracket
ROPS Tractors Only
Place Washers (7)
Behind Heat Shield
Exhaust
Bracket
1. Remove exhaust pipe from muffler and exhaust
bracket.
2. Remove exhaust bracket from tractor.
3. Place two washers (7) between heat shield
bracket and tractor. Secure with bolt removed
with exhaust bracket.
NOTE: Washers (7) are included in exhaust relo-
cation kit 1024092.
DP5
7. 44546 3/8 Hardened flat washer
Figure 1. Remove Exhaust Bracket
®
Nord-Lock Washer
The Nord-Lock® washer is a unique bolt securing sys-
tem that uses tension rather than friction. When the bolt
and/ or nut is tightened, the teeth grip and seat the mat-
ing surfaces. The wedge locking effect created makes
the bolt self-locking.
The advantage to the Nord-Lock washer is that it
achieves maximum security when locking fasteners.
These washers resist loosening caused by vibration or
dynamic loads. They are easy to install and remove and
provide positive locking at low and high preload levels.
They are reusable if lubricated before reuse.
Nord-Lock
secures bolts in
tapped holes.
Nord-Lock can
not be used on
washers that are
not locked in
place
Through holes
require two pairs
of NL washers.
Figure 2. Nord-Lock Washer
4 Mount Installation
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Right Mount
7
1. Attach right mount (1) to tractor chassis and
frame using four hex flange screws (7) and
Nord-Lock washers (9).
9
2. Attach to tractor frame using two cap screws (4)
and hardened flat washers (8).
3. Torque hardware to:
M14 x 2.0P x 40 mm . . . . . . . 111 lbs-ft (109 N-m)
M20 x 2.5P x 100 mm . . . . . 337 lbs-ft (457 (N-m)
8
1. 1023010 Right mount
4
4. 1024088 M20 x 2.5P x 100 mm HHCS
CL10.9
DP1
7. 1028750 M14 x 2.0P x 40 mm HFS CL10.9
8. 1006371 3/4 Hardened flat washer
9. 1026300 14 mm Nord-Lock washer
Figure 3. Right Mount Installed
Install Left Mount
1. Support fuel tank with hydraulic floor jack and
remove strap on bottom of tank. Lower tank for
access to mounting pad. See Figure 4.
2. Attach left mount (2) to tractor chassis using four
hex flange screws (6) and Nord-Lock washers
(9).
3. Attach to tractor frame using two cap screws (4)
and hardened flat washers (8).
NOTE: Make sure electrical wires are placed
between mount and tractor, and are not pinched.
Coolant lines should be on the out side of the
mount.
DP2
4. Torque hardware to:
Figure 4. Lower Fuel Tank
M14 x 2.0P x 40 mm . . . . . . . 111 lbs-ft (109 N-m)
M20 x 2.5P x 150 mm . . . . . 337 lbs-ft (457 (N-m)
4
8
5. Raise fuel tank back into position and secure
using hardware previously removed.
2. 1023011 Left mount
4. 1024088 M20 x 2.5P x 100 mm HHCS
CL10.9
6. 1028719 M14 x 2.0P x 60 mm HFS CL10.9
8. 1006371 3/4 Hardened flat washer
9. 1026300 14 mm Nord-Lock washer
9
6
DP3
Figure 5. Left Mount Installed
Mount Installation 5
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Exhaust Relocation Kit 1024092
ROPS Tractors only
1. Attach exhaust bracket (2) to the right loader
mount using two carriage bolts (4) hardened flat
washers (5), and hex nuts (6).
NOTE: Carriage bolts must be installed so that
the heads are inside the loader mount.
2. Torque carriage bolts to 170 lbs-ft.
3. Attach new exhaust stack (1) to tractor muffler
using hardware previously removed. Do not
tighten at this time.
4. Slide exhaust clamp (3) around exhaust stack.
5. Position stack and clamp against exhaust bracket
(2) and secure using lock nuts provided with
clamp.
6. Tighten exhaust stack hardware at muffler.
1. 1024093 Exhaust stack
2. 1023019 Exhaust bracket
3. 72130 Exhaust clamp 3/8 x 2-1/2
4.
5. 57817 5/8 Hardened flat washer
6. 230 5/8 NC Hex nut
5607 5/8 NC x 1-1/2 Carriage bolt
Figure 6. Exhaust Kit Installation
DP6
Figure 7. Exhaust Kit Installed
6 Mount Installation
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Grill Guard (Optional)
1. Attach grill guard (1) to the front of the tractor
using four cap screws (2) and flat washers (3).
2. Torque hardware to 244 lbs-ft.
1. 1018190 Grill guard
2. 1001377 M20 x 2.5P x 40 mm HHCS
3. 57798 3/4 Hardened flat washer
3
2
Figure 8. Grill Guard Installed
Install Oscillation Stops (Optional)
Check front tire clearance after loader has been
installed.
Using the loader, raise front of tractor off the ground
to achieve full oscillation of front axle. Turn front tires
completely to the right and left and check for tire con-
tact with loader or loader mounts. If tire contact is
present, install oscillation stops and/or adjust steering
stop bolts.
8
5
1. Attach oscillation stops (3) to right side of tractor
using cap screws (5) and hardened flat washer
(8). See Figure 9.
3
2. Repeat for oscillation stop installation on left side
of tractor.
DP8
3. Torque cap screws to 244 lbs-ft.
Figure 9. Oscillation Stop Installed, Right Side
3. 1018180 Oscillation stop
5. 1001377 M20 x 2.5P x 40 mm HHCS CL10.9
8. 1006371 3/4 Hardened flat washer
As a valued customer, Woods appreciates your comments. Once loader mount and
hydraulic hoses have been installed, please take a few minutes to complete the Loader
Mount Evaluation sheet that was supplied with your loader mount. Your comments will
help us continue to bring you quality products.
Mount Installation 7
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
1018219 & 1023597 HOSE KIT INSTALLATION
„ Keep hands and body away from pressurized
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
General Description
Hose Kit 1023597 is used for operating the LU132
loader and hose kit 1018219 is used for operating the
LU132-2 loader. To use these hose kits, the tractor
must be equipped with the manufacturer’s multi-func-
tion hydraulic control valve and lever. Multi-function
valve is located on the right side of the tractor under
the cab/operator’s platform.
DP7
Figure 10. Hydraulic Hose Connection
8 Hydraulic Installation
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Hydraulic Fittings
1. Locate the control valve under the right side of
the operator platform/cab and remove the four
plugs from the valve work ports.
2. 1012055 Adapter, M18 x 1.5P x 3/4 JICM
4. 26124 Quick coupler set, male/female 1/2
6. 313053 Elbow, 1/2 NPTM x 3/4 JICF 90°
7. 315058 Adapter, 1/2 NPTM x 3/4 JICF
8. 395058 Dust cap and plug set, black
9. 395061 Plastic spiral band, red
2. Install two adapters (2), elbows (6), and female
half of quick coupler set (4) into the two forward
ports of the control valve. Position elbows to point
forward.
10. 395062 Plastic spiral band, blue
3. Install two adapters (2), adapters (7), and female
half of quick coupler set (4) into the two rear ports
of the control valve.
11.
12.
56061 Plastic spiral band, green
56062 Plastic spiral band, yellow
NOTE: Install colored bands and dust plugs
between female quick coupler and fittings. See
Figure 12 for colored band locations.
DP8A
Figure 11. Hydraulic Fitting Installed, Bottom View
Figure 12. Hydraulic Fitting Installation
Install Hose Guide
Attach hose guide (3) to the right loader mount shoe
using two carriage bolts (13), hardened flat washers
(14), and hex nuts (15) as shown in Figure 13.
NOTE: Carriage bolts must be installed so that the
heads are inside the loader mount shoe as shown.
3. 1020934 Hose guide
13.
14.
15.
5607 5/8 NC x 1-1/2 Carriage bolt
57817 5/8 Hardened flat washer
230 5/8 NC Hex nut
Figure 13. Hose Guide Installation
MAN0572 (Rev. 1/30/2009)
Hydraulic Installation 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble Hoses
1. Attach male half of quick coupler set (4), colored
bands (10 & 11), and dust caps (8) to the end of
two loader supply hoses (1). See Figure 14.
1. 1002878 Hose, 74" x 1/2 NPTM x 3/4 JICM
(1018219 Hose Kit)
1. 1023473 Hose, 125" x 1/2 NPTM x 3/4 JICM
(1023597 Hose KIt)
2. Attach male half of quick coupler set (4), elbow
(5), colored bands (9 & 12), and dust caps (8) to
the end of other two loader supply hoses (1). See
Figure 14.
4.
5.
26124 Quick coupler set, male/female 1/2
3018 Elbow, 1/2 NPTM x 1/2 NPSF 90°
8. 395058 Dust cap and plug set, black
9. 395061 Plastic spiral band, red
10. 395062 Plastic spiral band, blue
3. Connect loader supply hoses to loader feedlines
following color scheme shown in Figure 15.
11.
12.
56061 Plastic spiral band, green
56062 Plastic spiral band, yellow
Figure 14. Hose Assembly
Figure 15. Hose Assembly & Loader Connection
10 Hydraulic Installation
MAN0572 (Rev. 1/30/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
2. Connect loader feedline hoses to tractor control
valve couplers. See Figure 15.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly advance tractor
forward, activating appropriate cylinders to
engage loader completely into mounts. Insert
mounting pins to secure loader.
●
●
●
●
Handle forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
Handle right -
Dump bucket or attachment (slow)
5. Place feedline hoses between Hose guide and
right loader mount as shown in Figure 17.
6. Check that all tractor hydraulic control lever
positions operate the loader movements correctly.
See Figure 16.
●
●
Handle right to limit -
Dump bucket or attachment (fast)
Handle to left - Rollback bucket or attachment
7. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
Figure 16. Single Lever Control Operation
8. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
9. Attach the plastic tie straps (included in kit) every
20-inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
10. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
lists in the Loader Operator’s Manual have been
completed.
Figure 17. Hose Routing
MAN0572 (Rev. 1/30/2009)
Hydraulic Installation 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2300003 LOADER MOUNTING KIT
2300003 LMK
DESCRIPTION
1018190 Grill Guard
QTY DESCRIPTION
Grill guard (optional)
REF PART
QTY
REF PART
1
2
3
4
5
6
7
8
9
1023010
1
1
2
4
2
4
4
6
8
Right mount
1
2
3
1018190
1
1023011
1018180
1024088
1001377
1028719
1028750
1006371
1026300
Left mount
1001377 †
57798 †
4
4
M20 x 2.5P x 40 mm HHCS CL10.9
3/4 Hardened flat washer
Oscillation stop
M20 x 2.5P x 100 mm HHCS CL10.9
M20 x 2.5P x 40 mm HHCS CL10.9
M14 x 2.0P x 60 mm HFS CL10.9
M14 x 2.0P x 40 mm HFS CL10.9
3/4 Hardened flat washer
14 mm Nord-Lock washer
†
Included with grill guard
HFS Hex Flange Screw
HHCS Hex Head Cap Screw
12 Parts
MAN0572 (11/10/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
1018219 & 1023597 HOSE KIT
REF PART
QTY
DESCRIPTION
REF PART
QTY
DESCRIPTION
1
1023473
4
Hose, 125" x 1/2 NPTM x 3/4 JICM
(1023597 Hose Kit)
8
395058
4
Dust plug & cap set, black (not
shown)
1
1002878
4
Hose, 74" x 1/2 NPTM x 3/4 JICM
(1018219 Hose Kit)
9
395061
395062
56061
56062
5607 *
57817
230 *
2
2
2
2
2
2
2
2
Plastic spiral band, red
Plastic spiral band, blue
Plastic spiral band, green
Plastic spiral band, yellow
5/8 NC x 1-1/2 Carriage bolt
5/8 Hardened flat washer
5/8 NC Hex nut
10
11
12
13
14
15
16
2
3
4
5
6
7
1012055
1020934
26124
4
1
4
2
2
2
Adapter, M18 x 1.5M x 3/4 JICM
Hose guide
Quick coupler set, male/female 1/2
Elbow, 1/2 NPTM x 1/2 NPSF 90°
Elbow, 1/2 NPTM x 3/4 JICF 90°
Adapter, 1/2 NPTM x 3/4 JICF
3018
313053
315058
88 *
Plastic tie (not shown)
* Standard hardware, obtain locally
Parts 13
MAN0572 (11/10/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
1024092 EXHAUST RELOCATION KIT
REF PART
QTY
DESCRIPTION
Exhaust stack
1
2
3
4
5
6
7
1024093
1
1
1
2
2
2
2
1023019
72130
5607 *
57817
230 *
Exhaust bracket
Exhaust clamp
5/8 NC x 1-1/2 Carriage bolt
5/8 Hardened flat washer
5/8 NC Hex nut
44546
3/8 Hardened flat washer (not shown)
* Standard hardware, obtain locally
14 Parts
MAN0572 (11/10/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
FINE THREAD
A
A
MARKING ON HEAD
MARKING ON HEAD
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Metric 8.8
Metric 10.9
N-m lbs-ft
Metric 8.8
Metric 10.9
N-m lbs-ft
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 10/10/2005)
Appendix 15
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG ............................................................ Agriculture
ATF .............................. Automatic Transmission Fluid
BSPP........................... British Standard Pipe Parallel
BSPTM .............. British Standard Pipe Tapered Male
CV...................................................Constant Velocity
CCW.............................................Counter-Clockwise
CW..............................................................Clockwise
F .....................................................................Female
GA ...................................................................Gauge
GR (5, etc.)..........................................Grade (5, etc.)
HHCS ...................................... Hex Head Cap Screw
HT..........................................................Heat-Treated
JIC ...............Joint Industry Council 37° Degree Flare
LH............................................................... Left Hand
LT..........................................................................Left
m....................................................................... Meter
mm.............................................................. Millimeter
M.........................................................................Male
MPa ....................................................... Mega Pascal
N.....................................................................Newton
NC.................................................... National Coarse
NF .........................................................National Fine
NPSM................... National Pipe Straight Mechanical
NPT.........................................National Pipe Tapered
NPT SWF........National Pipe Tapered Swivel Female
ORBM .........................................O-Ring Boss - Male
P......................................................................... Pitch
PBY.....................................................Power-Beyond
psi........................................ Pounds per Square Inch
PTO....................................................Power Take Off
QD.................................................. Quick Disconnect
RH............................................................ Right Hand
ROPS......................... Roll-Over Protective Structure
RPM ...................................... Revolutions Per Minute
RT ......................................................................Right
SAE........................ Society of Automotive Engineers
UNC ................................................... Unified Coarse
UNF.........................................................Unified Fine
UNS.................................................... Unified Special
Bolt Torque & Size Charts (Rev. 10/10/2005)
16 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of delivery
Model Number
BW1260, BW1620, BW1800, BW2400
to the original purchaser)
8 years
BW240HD
7 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X,
BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
components
5 years
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72, TBW150C
Blade
spindles
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2,
9204RD-2
3 years
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3, BW1260,
BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
Rust-through
10 years
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev 11/24/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser
with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty
does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or
otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any
way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this
Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after
such defect or noncompliance is discovered or should have been discovered, routed through the dealer and
distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete
such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO
OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS
WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly
or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty,
negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing,
Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of
crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain
materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including
without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify,
or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
©2006 Woods Equipment Company. All rights reserved. WOODS, and the Woods logo are trademarks of Woods Equipment Company. All other
trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective
companies or mark holders. Specifications subject to change without notice.
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
|