Operating Instructions (ENG)
MODEL : CMPS
10070050
CMPSR
10070080
FROM SN: 1000170681
Read instructions before operating the machine.
C
86290230 04/20/07
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log/Overview.........................1
Table of Contents..........................................2
GROUP PARTS LIST
Controls ........................................................5-1
Recovery Tank..............................................5-3
Solution Tank.............................................. 5-5
Vacuum....................................................... 5-7
Wheels & Frame ........................................ 5-9
Pump .......................................................... 5-11
Tools – Standard ........................................ 5-15
Vacuum Hose Rack – CMPSR................... 5-17
Wiring – Schematic..................................... 5-19
Suggested Spare Parts............................... 5-20
Dry Clean Option ........................................ 5-21
Low Flow Spray Gun Option....................... 5-23
Grout Cleaner Option.................................. 5-25
High Pressure Wand Option....................... 5-27
Carpet Tool Option ..................................... 5-29
Storage Bag Option .................................... 5-31
Chemical Lock Option................................. 5-33
Notes .......................................................... 5-35
Warranty. .................................................... 5-36
HOW TO USE THIS MANUAL
How to use this Manual.................................1-1
SAFETY
Important Safety Instructions ........................2-1
Hazard Intensity Level. .................................2-2
Grounding Instructions..................................2-3
Safety Label Location. ..................................2-4
OPERATIONS
Technical Specifications. ..............................3-1
How the Machine Works...............................3-2
Components..................................................3-3
Controls.........................................................3-4
Machine Operation........................................3-6
Chemical Operations ....................................3-8
MAINTENANCE
Maintenance. ................................................4-1
Float Shut-Off..........................................4-2
Strainer....................................................4-2
Circuit Breakers.......................................4-2
Vacuum Motor Replacement...................4-3
Solution Pump Replacement...................4-4
Regulating Unloader…………………….. 4-4
Periodic/Daily Maintenance ..........................4-5
Service Schedule..........................................4-5
Machine Troubleshooting..............................4-6
Notes.............................................................4-7
CMPS 86290230 04/20/07
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
This manual contains the following sections:
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards is identified that could
result in product or personal injury, or severe injury
resulting in death.
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
-
-
MAINTENANCE
PARTS LIST
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
-
-
-
-
-
-
Vacuum Motor
Solution Pump
Daily Maintenance
Periodic Maintenance
Service Schedule
Machine Troubleshooting
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
DEALER NAME ______________________________
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
Copyright 2003 Windsor Industries, Printed in USA
The model and serial number of your machine is on
the bottom back-end of the machine.
-
-
PRV NO. – reference number
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs. If
column has an asterisk (*), call
-
-
manufacturer for serial number.
NOTES – column for information not
noted by the other columns.
-
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
CMPS 86290230 02/22/07
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
WARNING:
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before
maintenance or service.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near
children.
Do not point spray gun at people.
Use only as described in this manual. Use only manufacturer’s recommended components and
attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding
the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or
dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord
around sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
CMPS 86290230 02/22/07
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use Windsor approved replacement parts.
.
CMPS 86290230 02/22/07
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING INSTRUCTIONS
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
ELECTRICAL:
In the USA, this machine operates on a
standard 15 amp 115V, 60 Hz, A.C. power
circuit. The amp, hertz, and voltage are listed
on the data label found on each machine.
Using voltages above or below those indicated
on the data label will cause serious damage to
the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must
be at least one size larger than the power cord
on the machine, and must be limited to 50 feet
(15.5m) in length.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the appliance - if it will not fit the outlet;
have a proper outlet installed by a qualified
electrician.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides
a path of least resistance for electric current to
reduce the risk of electric shock. This
appliance is equipped with a cord having an
equipment-grounding conductor and grounding
plug. The plug must be inserted into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes
and ordinances.
GROUND-FAULT CIRCUIT-INTERRUPTER
PROTECTION
This pressure washer is provided with a
(GFCI) built into the plug of the power supply
cord. This device provides additional protection
from the risk of electric shock. Should
replacement of the plug or cord become
necessary, use only identical replacement parts
that include GFCI protection. If the GFCI is not
the AUTOMATIC RESET TYPE, it must be
manually TESTED and RESET each time the
cleaning system is plugged in. Press firmly to
assure internal spring activates switch. Push
“test“ then push “reset”. Motor will not start if
GFCl does not reset. Check circuit breakers or
outlet. If circuit breaker is not tripped and unit
will not reset, contact local service center.
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like
the plug in “Fig. A”. A temporary adaptor that
looks like the adaptor in “Fig. C” may be used to
connect this plug to a 2-pole receptacle as
shown in “Fig. B”, if a properly grounded outlet
is not available. The temporary adaptor should
be used only until a properly grounded outlet
(Fig. A) can be installed by a qualified
electrician. The green colored rigid ear, lug, or
wire extending from the adaptor must be
connected to a permanent ground such as a
properly grounded outlet box cover. Whenever
the adaptor is used, it must be held in place by
a metal screw.
CMPS 86290230 02/22/07
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Compass™. If, at any time, the labels
become illegible contact your Windsor representative for prompt replacement.
WARNING LABEL 86242230
PRV NO. 500009
CMPS 86290230 02/22/07
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ITEM
DIMENSION/CAPACITY
Electrical
115V, 12A, 60HZ
Electric Pump Motor
Solution Pump
Electric Vacuum Motor
Waterlift
1/3hp, 1725rpm
500psi (34 bars), Axial plunger
2stage, 1.25hp (2.80m3/min.)
82 in. (208 cm)
Solution Capacity
29 gallons (111L)
Recovery Capacity
Wheels
19 gallons (70L)
-
-
Front (2)
Rear (2)
6 in. dia. (15.24cm) X 1.5
12 in. dia. ( 30.48cm)X 1.75
155 lb. (70kg)
157 lb. (71kg)
36 in. (91.4cm)
Dimensions – Weight (CMPS)
Dimensions – Weight (CMPSR)
Dimensions – Length (CMPS)
Dimensions – Length (CMPSR)
Dimensions - Height
41.5 (105.4 cm)
43 in. (109.2cm)
Dimensions - Width
Power Cable
24.75 in. (62.87cm)
50 ft. (127m) 14 gauge
LENGTH
CMPSR*
HEIGHT
LENGTH
CMPS
WIDTH
SIDE VIEW
FRONT VIEW
*NOTE: Hose rack standard ONLY on CMPSR.
SPECIAL NOTES:
The sound pressure level at 1m from the machine was measured to be 79 dBA. This was a nearfield,
broadband measurement taken in a typical industrial environment on a tile floor. This appliance
contains no possible source of impact noise. The instantaneous sound pressure is below 63 Pa.
The weighted root mean square acceleration at the operator’s arms was measured to be below
2.5m/s2. This was a tri-axial, third-octave-band measurement made during normal operation on a
composite tile floor. The measurement and related calculations were made in accordance with ANSI
S3.34-T986.
CMPS 86290230 02/22/07
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW THE MACHINE WORKS
The Compass™ is a multi-functional cleaning
machine intended for commercial use. The
appliance applies chemical at low pressure and
uses high pressure to clean with. Then the
soiled water is vacuumed back into the
recovery tank.
The function of the chemical system is to
dispense chemical into the clean water system.
The chemical system consists of the chemical
reservoir, chemical cap and a chemical-
metering selector. The chemical reservoir
stores and dispenses chemical into the clean
water system. The chemical-metering selector
meters the amount of chemical and selects
between chemical A or B and turn chemical off.
The machine's primary systems are the clean
water system, recovery system, chemical
system and pressure washer system.
The function of pressure washer system is to
clean fixtures and other surfaces. The pressure
washer system consists of a pump, high-
pressure hose and spray gun. The pump
delivers cleaning solution to the tools. The
high-pressure hose connects the pump to the
spray gun. The spray gun is an adjustable Hi-Lo
that applies clean water and chemical to the
surface being cleaned.
The function of the clean water system is to
store clean water and deliver it to the available
tools. The clean water system consists of the
clean water tank, strainer and check valve. The
clean water tank stores water until it is delivered
to the tools. The strainer protects the check
valve and pump from debris.
The function of the recovery system is to
vacuum the soiled water back into the recovery
tank. The recovery system consists of the
wand and wheeled squeegee, vacuum motor,
float shut-off and recovery tank. The wand and
wheeled squeegee wipes the dirty solution off
the floor. The vacuum motor provides suction
to draw the dirty solution off the floor and into
the recovery tank. The float shut-off protects
the vacuum fan from over filling. The recovery
tank stores the dirty solution.
CMPS 86290230 02/22/07
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
1. Control Panel
2. Solution Tank
3. Solution Tank Lid
4. Solution Tank Drain Hose
5. Solution Tank Fill Hose
6. Recovery Tank
7. Recovery Tank Lid
8. Recovery Tank Drain Hose
9. Chemical Siphon Caps
10. Electrical Cord
11. High Pressure Hose Storage
12. Vac Hose Rack (Standard CMPSR only)
CMPS 86290230 02/22/07
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
8
3
7
2
4
1
5
6
1. Solution Accessory Tool Hook-Up
2. Vacuum Accessory Tool Hook-Up
3. Pump Switch
6. Caster Lock
7. Vacuum Circuit Breaker
8. Pump Circuit Breaker
4. Vacuum Switch
5. Chemical Selector and Metering Valve
CMPS 86290230 02/22/07
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
1. SOLUTION ACCESSORY TOOL HOOK-UP
Used for various auxiliary-cleaning tools.
2. VACUUM ACCESSORY TOOL HOOK-UP
To use accessory tool, remove hose from vac shoe and attach to
accessory tool adaptor.
3. PUMP SWITCH
Turns the pump On and Off.
4. VACUUM SWITCH
Turns the vacuum motor On and Off.
5. CHEMICAL SELECTOR AND METERING VALVE
Meters the amount of chemical being dispensed and selects between
chemical A or B and turn off.
6. CASTER LOCK
Locks the wheels in place to keep the machine from moving.
7. VACUUM CIRCUIT BREAKER
10 Amp. Protects the vacuum motor.
8. PUMP CIRCUIT BREAKER
6 Amp. Protects the pump motor.
CMPS 86290230 02/22/07
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
FILLING THE MACHINE
Do not put defoamer, solvents
spotter or prespray chemicals in
the solution tank.
3. Attach the adapter cap and intake hose to the
CompassTM Chemical bottle. Refer to the
CompassTM Chemical Label for the desired
dilution.
1. Always use gloves and eye protection. Never
spray solution towards people.
4. Position the CompassTM machine in the door
way, lock front casters. Start at furthest point in
the room and work towards the door.
2. To fill Use fill hose or pour directly into solution
tank. Use COLD WATER. Add 1 ½ oz of
CompassRinse TM to each full solution tank.
5. Always Spray chemical using low pressure.
CMPS 86290230 02/22/07
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
7. Use brush or grout tool for heavy soiled areas.
10. Store and secure hoses and tools neatly.
8. Turn Chemical off. Pressure clean by rinsing
surfaces at high pressure.
11. Drain machine at proper disposal areas. Use
pressure gun to rinse and clean recovery tank.
9. Use Squeegee or Gulper tool to remove
standing water.
12. When using dry filter, gently remove and wash
with water after every use. Allow to dry before
re-using.
CMPS 86290230 02/22/07
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Care must be exercised in the use of all
chemicals. Chemicals are poisonous and
can pose a health risk. Read and follow
manfacturers instructions regarding
dangers and correct usages.
The internal parts of the pump used in the
machine are suitable for use with most carpet
cleaning chemicals. But they are susceptible to
chemical attack from some cleaning
substances, such as hydrocarbon solvents and
chlorinated bleaches. These non-compatible
materials are not of the type used for carpet
cleaning.
CHEMICALS
Suitable Chemicals Non-Compatible
Alkalis
Aldehydes
Detergents
Hydroxides
Soaps
Aromatics Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
Vinegar
Chlorinated Bleaches
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
D-Limonene
Only use chemicals approved for use with this
machine. Use of non-compatible chemicals
may cause machine damage and will not be
covered under the warranty. Carefully read
ingredients on manfacturer’s label before using
any product in this machine.
Do not let pump run dry.
Do not let pump run unattended.
CMPS 86290230 02/22/07
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1. Float Shut-Off
2. Strainer
5. Pump
6. Adjustable Unloader Valve
3. Circuit Breakers
4. Vacuum Motor
CMPS 86290230 02/22/07
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1. FLOAT SHUT-OFF
3. CIRCUIT BREAKERS
The float shut-off is located inside the
recovery tank. The purpose of the float
shut-off is to notify the user that the
recovery tank is full. Remove daily and
clean any debris for maximum airflow.
Circuit breakers interrupt the flow of power
in the event of an electrical overload. When
a circuit breaker is tripped, reset it by
pressing the exposed button. If a circuit
breaker continues to trip, the cause of the
electrical overload should be found and
corrected.
2. STRAINER
The strainer is located on the lower right
side between the front and rear wheels.
The strainer protects the check valve and
pump from debris. If there is little or no
solution flow to the ground, check the
stainer for debris. Drain the solution tank
and clean the solution strainer. To remove
the strainer, turn the bottom part of the
strainer counterclockwise until the bottom is
separated. Clean out the debris from the
wire mesh and reassemble. Make sure the
o-ring gasket is in place when reassembled.
6 Amp. Protects the pump
motor.
10 Amp. Protects the vacuum
motor.
CMPS 86290230 02/22/07
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
4. VACUUM MOTOR
(Refer to vacuum group in the parts section of
manual).
Vacuum Motor Carbon Brushes Replacement (Windsor)
End Cap
WARNING: The green
ground wire must be
attached for safe operation.
See wiring diagram.
Carbon
Brushes
ONLY QUALIFIED MAINTENANCE PERSONNEL
ARE TO PERFORM THE FOLLOWING REPAIRS.
VACUUM MOTOR REPLACEMENT
1. Turn off all switches and unplug machine.
2. Remove recovery tank.
3. Remove the 5 screws holding the vacuum motor
cover to the solution tank.
4. Locate the vacuum motor wires and disconnect
at the connector.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
5. Remove the vacuum motor.
6. Reverse process to install.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3
[9.5mm]
8
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
CMPS 86290230 02/22/07
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
5. PUMP
6. REGULATING UNLOADER
ONLY QUALIFIED MAINTENANCE
PERSONNEL ARE TO PERFORM THE
FOLLOWING REPAIRS.
ONLY QUALIFIED MAINTENANCE
PERSONNEL ARE TO PERFORM THE
FOLLOWING REPAIRS.
SOLUTION PUMP REPLACEMENT
1. Turn off all switches and unplug machine.
2. Tilt machine back so bottom is exposed.
3. Remove the 6 screws that fasten the frame
to the solution tank.
UNLOADER REPLACEMENT
1. Turn off all switches and unplug machine.
2. Tilt machine back so bottom is exposed.
3. Remove the 6 screws that fasten the frame
to the solution tank.
4. Remove the solution hoses from the fittings
on the pump.
4. Remove the solution hoses from the fittings
on the pump.
5. Reverse process to install.
5. Remove the unloader.
6. Reverse process to install.
PUMP REPLACEMENT KITS
MOTOR ONLY 86290270
PUMP HEAD ONLY 86290280
CAM & BEARING KIT
86290330
VALVE & O-RINGS KIT
(BOTH SIDES)
86290340
PLUNGER & SEALS KIT
86290350
CMPS 86290230 02/22/07
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
DAILY/REGULAR MAINTENANCE
PERIODIC MAINTENACE
Before making any adjustments to the machine,
disconnect the power cord from the electrical source.
1. Empty unused cleaning solution from the
solution tank.
2. Inspect and clean filter screen in solution tank.
3. Flush pumping system with 4 to 7 liters of clean
water.
Twice a month, flush a white vinegar solution (one
quart vinegar to two gallons of water) or anti-
browning solution (mixed as directed) through the
machine. This will prevent build-up of alkaline
residue in the system. If spray jets become clogged,
remove the spray tips, wash them thoroughly, and
blow dry.
4. After each use, rinse tank with fresh water.
Periodically inspect the recovery tank and
decontaminate if necessary, using a Hospital
Grade Virucide or a 10-1 bleach to water
solution. Waste water should be disposed of
properly.
5. Remove filter to clean. Filters used for wet pick-
up including striper must be thoroughly cleaned
before being allowed to dry.
6. Check spray jets for full spray pattern.
NOTE: Worn filters can affect vacuum
performance. Replace the filter when it becomes
worn out and normal cleaning will not restore
vac performance.
NOTE: Do not use pins, wires, etc. to clean nozzles
as this could destroy the spray pattern.
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked
hoses should be repaired or replaced to eliminate
vacuum or solution pressure loss. The electrical
cable must be well insulated and cable connector
screw kept tight. If the cable insulation is broken or
frayed, repair or replace immediately. Don’t take
chances with elctrical fire or shock.
DAILY
*
WEEKLY
QUARTERLY
SERVICE SCHEDULE
Check machine for cord damage
Check recovery dome and gasket for damage and
cleanliness
Check hoses for wear, blockages, or damage
Check handles, switches, and knobs for damage
Check vac motor intake filter and clean
Run one gallon of water through system
*
*
*
*
*
*
Clean out recovery tank and check float valve to make
sure it moves freely
Clean out solution tank and remove and clean vacuum
intake screen
*
*
Clean outside of all tanks and check for damage
Run vac motor for at least one minute to allow motor to
dry
Store with dome off tank to allow the tank to dry
*
*
Check all bearings for noise
Check all gaskets for wear and leakage
*
*
Check vacuum intake screen for damage; replace if
necessary
*
Check pump pressure; observe spray pattern and
check with gauge if necessary
Check and clean solution screen
Check cables for fraying
Check overall performance of machine
Check vac motor carbon brushes
*
*
*
*
*
CMPS 86290230 02/22/07
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Dead electrical circuit
Faulty power cord
Check building circuit breaker or fuse box.
Replace
Loss of Power
GFCI breaker is tripped
Reset breaker on power cord
Equipment not grounding
Receptacle not grounded
Follow grounding instructions exactly
Contact an electrician to check building’s wiring
Have a trained service technician check machine’s
wiring
Electrical shock
Internal wiring problem
Worn motor brushes
Motor worn out
Faulty switch
Replace
Replace
Replace
Vac motor speed varies
or doesn’t run
Loose vacuum dome
Vacuum circuit breaker
tripped.
Center and seal dome over tank
Reset breaker.
Crack in dome of poor joint Replace or repair using acrylic plastic cement only
Lint or dirt clogging
With power off clean screen
vacuum screen
Loss of vacuum
Loose cuffs on vacuum
Tighten cuffs turning counterclockwise
hose
Vac motor seals leaking
Floor tool vac chamber
clogged
Replace
Wash out with hose. Pick lint out with a wire
Vac motor, hose, or dome
gasket
Replace
Pump inlet screen plugged Clean inlet screen
Pump circuit breaker
Reset breaker.
tripped.
Faulty pump switch.
Faulty pump motor.
Call for service.
Call for service.
Press trigger to open valve on cleaning wand to
relieve air
Pump runs no solution
Pump air locked
Internal or external
solution line damaged and Replace
leaking
Jet orifice on cleaning
wand is to large
Internal pump components
wearing out
Total jet opening for 100 psi should be .06 to .08
Replace, see pump kit components (pg 4-3)
Pump runs, loss of
pressure
Note: Operation of pump using a wand or hand tool with an orifice of less than .06
will cause pump to cavitate or pulsate and could result in premature wear of pump
components.
Check valves in pump
Take piston from BPR and lubricate with Superlube.
head for particles or cuts in
If problem still exists change BPR kit
seals
Unit not plugged in
Loose wiring
Connect unit to 3 prong grounded outlet
See dealer
Pump will not run
Solution hose fitting hard
to connect
Clean with steel wool. Soak in acetic acid (white
vinegar). Lubricate lightly with silicone base lubricant.
Corrosion on fittings.
CMPS 86290230 02/22/07
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
CMPS 86290230 02/22/07
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
CMPS 86290230 02/22/07
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
86243990
86234690
86270990
86258930
86197390
86279560
86230210
86001940
86002450
86002010
500780
270012
57090
84187
31021
87178
14832
14635
22015
14942
72128
72130
-
61415
70696
39634
270699
57104
87016
36235
20016
1
1
2
1
1
3
1
1
1
2
2
1
1
1
4
2
2
2
1
2
2
LABEL, COVER PANEL
COVER, SWITCH PANEL
NUT, 10-32 HEX NYLOCK SS
VALVE, CHEMICAL METERING
ELBOW, 1/4 NPT 45º STREET
WASHER, 5/8 ID X 1.7 OD 0.05 T
BREAKER, 6A VDE CIRCUIT
BREAKER, 10A CIRCUIT
COUPLER, 1/4 QD
10
BOOT, 3/8 CIRCUIT BREAKER
SWITCH, DPDT 2-POSITION POCKER
SWITCH, SPST 2-POSITION ROCKER
LABEL, SWITCH PANEL, CMPS
PANEL, SWITCH CONTROL
SCR, #10 X 3/4 PTHSMS SS
HOSE, 1/4 NYLOBRAID X 23”
CAP, CHEM FEED W/DIP TUBE
NUT, 10-32 W/ STAR WASHER PLTD
WASHER, #10 LOCK EXT STAR SS
GASKET, SWITCH CARLING
CLAMP, 1/4 ID HOSE
11A 86007130
11B 86007140
12
13
14
15
16
17
18
19
20
86290050
86078140
86276600
86282280
86232110
86270800
86010640
86238030
86233090
CMPS 86290230 02/22/07
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK
CMPS 86290230 02/22/07
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK
SERIAL NO.
NOTES:
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
86271830
86277040
86010670
86070510
86197940
86070450
86004190
86177050
86004510
86004500
86031160
86199840
86033250
86004000
86002620
86275800
86241450
86002870
86264940
57283
70781
87029
140659
40027
140651
39337
03-000176
41391
41390
75438
090-12A
66402
35255
260-64A
70546
500806
27417
27051
1
11
11
2
1
1
1
2
1
1
1
1
1
1
1
6
1
1
NUT, 3/8 NPT PLASTIC
SCR, 5/16-18 X 1/2 HHCS SS NP
WASHER, 5/16 FLAT SS
BRKT, TANK MOUNT
HOSEBARB, 3/8 MPT X 1/2 90º DL
BRKT, UTILITY MOUNT
HOSE, 1.5 BLK VAC X 24”
CLAMP, HOSE #20
HOSE, INSERT
HOSE, CAP
TANK, RECOVERY COMPASS
FLOAT CAGE ASM, COMPLETE
PIPE ASM, VACUUM STACK
GASKET, TANK LID
ACCESS COVER CLEAR 6” W/ RIM
SCR, 8 X 3/4 PFHT/S BLK ZINC
INSTRUCTION CARD, CMPS
CORD, 99807 1/8 X 12”
2
CABLE TIE, 11.38” UL/CSA
CMPS 86290230 02/22/07
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK
CMPS 86290230 02/22/07
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK
SERIAL NO.
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
86290070
86239680
86276600
86243960
86275800
86226970
86197910
86233150
86282260
86240400
86243970
86277040
86070490
86260810
86234510
86256080
86256070
86006590
-
1
1
10
1
6
1
1
1
1
1
1
2
2
1
1
3
2
2
TANK, SOLUTION CMPS
HOOK, HOSE STORAGE
SCR, #10 X 3/4 PTHSMS SS
LABEL, COMPASS LEFT
SCR, 8 X 3/4 PFHT/S BLK ZINC
ACCESS COVER, CLEAR 3.5” W/ RIM
HOSEBARB, 1/2 MPT X 1/2 POLY DL
CLAMP, 3/8 HOSE (D-SLOT)
HOSE, 1/2 CLEAR X 34”
HOSEBARB, 3/4MPT X 1/2 HOSE
LABEL, COMPASS RIGHT
SCR, 5/16-18 X 1/2 HHCS SS NP
BRKT, HOOK TAB
41476
70696
500777
70546
49-876215
40022
20042
39630
40077
500778
70781
140657
39633
270018
730232
730231
70088
HOSE ASM, SOLUTION FILL HOSE
CORD, 1/4 DIA BUNGEE
STRAP, 1.5” X 7.00” VELCRO
STRAP, 1.5” X 4.50” VELCRO
SCR, 10-32 X 1/2 PPHMS SS NP
CMPS 86290230 02/22/07
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM
20
19
21
22
28
14
GROUND
WIRE
27
(26)
27
10
9
23
11
16
18
12
13
24
14
GROUND
WIRE
4
26
15
25
CMPS 86290230 02/22/07
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM
SERIAL NO.
FROM
REF
PART NO.
PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
9
10
11
-
-
-
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
86237850
86092220
86238020
86002390
86282120
86093590
86004190
86276940
86201970
86003760
86202040
86202070
86135320
86028720
86010630
86005810
86010640
86274370
86264930
86002380
86266130
86010670
86277040
86237870
86078870
86004370
86233260
86240240
86269400
86005700
86006590
35268
270010
36234
20063
39582
620004
39337
70758
065-92
35166
360-04A
360-04B
140687
53266
87013
57245
87016
70191
27050
20046
76044L
87029
70781
35270
620018
39547
20092
39697
88951
57104
70088
2
1
1
1
1
1
1
3
3
1
1
-
GASKET, 5.0 OD X 1.75 ID X .38T
COVER, VAC MOTOR
GASKET, 5.0 OD X 3.1 ID X .75
CLAMP, 1.75” WORM GEAR X .312
HOSE, VAC EXHAUST X 9”
PLATE, VAC MOUNT
HOSE, 1.5 BLK VAC X 24”
SCR, 1/4-20 X 3.5 HHCS SS NP
VAC SPACER, 2-1/4 II STAGE
GASKET, VAC MOTOR
VAC MOTOR, 120V 5.7 2 ST TD
BRUSHES, VAC FOR 116392-00
BRUSH SET, 120V VAC WINDSOR
VAC MOTOR ASM, 115V W/ TERM
WASHER, 1/4 ID X 5/8 OD SS
NUT, 1/4-20 HEX NYLOCK SS
WASHER, #10 LOCK EXT STAR SS
SCR, 10-24 X 1/2 HHTC TYPE 23
CABLE TIE, 3.5” UL/CSA
CLAMP, 2.25” WORM GEAR
TERM, 14G MALE COUPLER F/I
WASHER, 5/16 FLAT SS
SCR, 5/16-18 X 1/2 HHCS SS NP
GASKET, 5.0OD X 2.0ID X .50T
PLATE, COVER VAC MOUNT
HOSE ASM, 1.5 BLK VAC X 21
CLAMP, 3.5” WORM GEAR
-
-
3
3
2
1
1
1
2
5
5
1
1
1
1
1
1
2
1
HOSE, 3.15ID X 7.0L VENT
WIRE, 10” GRN/18 76008 X 76008
NUT, 10-32 W/ STAR WASHER PLTD
SCR, 10-32 X 1/2 PPHMS SS NP
CMPS 86290230 02/22/07
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEELS & FRAME
CMPS 86290230 02/22/07
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEELS & FRAME
SERIAL NO.
NOTES:
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
86202280
86271380
86010670
86277040
86014710
86276940
86232620
86078800
86270830
89252
57196
87029
70781
-
70758
18043
620001
57023
2
2
18
10
1
8
2
1
8
WHEEL, 12” BLK CNTRD HUB
NUT, 1/2 PUSH-ON DOME CAP
WASHER, 5/16 FLAT SS
SCR, 5/16-18 X 1/2 HHCS SS NP
FRAME, PUMP/WHEEL MNT
SCR, 1/4-20 X 3.5 HHCS SS NP
CASTER, 6” DIA X 4.63 SWIVEL
PLATE, MOUNT CASTER
NUT, 5/16-18 HEX NYLOCK SS
CMPS 86290230 02/22/07
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP
15
14
13
16
17
11
12
10 5
13
9
8
7
18
19
6
4
3
2
1
CMPS 86290230 04/20/07
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
67488
86180220 11-800276
DESCRIPTION
NOTES:
1
2
86223390
1
1
1
1
1
1
4
1
2
1
1
1
2
1
1
1
1
4
1
RECTIFIER, 50A 600V BRIDGE
ELL, 3/8 BR
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
86290290
86197510
86197540
86282270
86233150
86256090
86001530
86281980
86281390
86290280
86233090
86281060
86177610 11-800090
86290310
86290300
86190520 11-800224
86290270
-
UNLOADER, PMPTC EVK-520-450
HOSEBARB, 3/8MPT X 3/8 BR DL
HOSEBARB, 3/8MPT X 1/2 DL
HOSE, 1/2ID WIRE BOUND X 25”
CLAMP, 3/8 HOSE (D-SLOT)
STRAINER, 1/2 FPT 80 MESH
HOSEBARB, 1/2MPT X 1/2 HOSE 90
HOSE, 1/2ID WIRE BOUND X 5”
HOSE, 3/8ID WIRE BOUND X 12”
PUMP, PUMPTEC, 500PSI
CLAMP, 1/4 ID HOSE
HOSE, 1/4ID NYLOBRD X 8”
CONN, 3/8FP X 1/4P BR
INJECTOR, TEE 3/8M X 3/8M 1/4 BR
HOSE, PULSE 48” 3/8MPT X 3/8FPT
PLUG, 3/8 SOCHD BR
40010
40013
39631
20042
730262
40039
39549
39356
-
NOT SHOWN
20016
39265
-
-
-
MOTOR, 120V CIM-PUMPTEC
CMPS 86290230 04/20/07
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP
1
2
3
4
5
6
CMPS 86290230 04/20/07
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP
SERIAL NO.
FROM
REF PART NO.
PRV NO. QTY
DESCRIPTION
NOTES:
COMPLETE
ASSEMBLY
1
86014510
-
1
PUMP ASM, 500 PSI 120V CMPS
2
3
4
5
6
86004370
86002390
86264940
86010650
86270990
39547
20063
27051
87018
57090
1
1
2
4
4
HOSE ASM, 1.5 BLK VAC X 21
CLAMP, 1.75 WORM GEAR X .312
CABLE TIE, 11.38 UL/CSA
WASHER, #10 X 9/16 OD
NUT, 10-32 HEX NYLOCK SS
CMPS 86290230 04/20/07
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS - STANDARD
1
2
5
3
4
6
17
13A
13B
7
8
16
9
10
11
CMPS 86290230 04/20/07
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS - STANDARD
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13A
13B
14
15
16
17
18
19
20
86257660
86257650
86257640
86257670
86257680
86257620
86257690
86290390
86005590
86290400
86005580
86200350
86240180
86240250
86202160
86234200
86290380
86002400
86241930
86290410
86269560
02478
02477
02475
02479
02480
02473
02481
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
TOOL, HAND SQUEEGEE
TOOL, SCRUB BRUSH HANDLE
TOOL, GULPER
TOOL, TILE BRUSH
TOOL, ALUMINUM WAND
TOOL, WHEELED SQUEEGEE
TOOL, DOOR WEDGE
GUN, PRESSURE WASH
NIPPLE, 1/4 CLOSE
NOZZLE, ADJUSTABLE HI-LO
NIPPLE, 1/4 FPT QD
HOSE ASM, 1/4HP SLTN 25 FT
HOSE ASM, 1.5 X 30 FT
56014
-
56012
39578
39637
39703
320-05
23215
-
20064
47419
-
NOT SHOWN
HOSE ASM, 1.5 BLK VAC X 30’
STRAP, VELCRO
CMPSR ONLY
NOT SHOWN
NOT SHOWN
SERVICE ONLY
CORD SET, 14/3 X 50 FT GFCI YLW
TOOL, SPRAY GUN ASM
CLAMP, 2.9” WORM GEAR X .312W
KIT, SQUEEGEE TOOL BLADES
NOZZLE REPLACEMENT JET
COMPASS TRAINING VIDEO
1
-
-
SERVICE ONLY
SERVICE ONLY
NOT SHOWN
96V123R
1
CMPS 86290230 04/20/07
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC HOSE RACK – CMPSR ONLY
CMPS 86290230 04/20/07
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC HOSE RACK - CMPSR
SERIAL NO.
NOTES:
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
HOSE RACK
SCR, #10 X 3/4 PTHSMS SS
SCR, 10-32 X 1/2 PPHMS SS NP
SCR, 1/4-20 X ½ PHTR BLK DL
CLAMP, 1/4X1/4 BLT VIN DP
NUT, ¼-20 HEX NYLOCK
1
2
3
4
5
6
7
86240630
86276600
86006590
86275210
86270250
86005680
86068180
49499
70696
70088
1
3
2
2
2
2
1
70384
03-000133
57047
140710
BRACKET, TOP HOSE RACK
CMPS 86290230 04/20/07
5-18
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING – SCHEMATIC
PUMP
MOTOR
BLK
GRN/YEL
WHT
INCLUDED W/PUMP MOTOR
86015000
PANEL
GROUND
GRN/YEL
WHT
POWER
BLK
POWER
CORD
WHT
GRN/YEL
BLK
86014950
PUMP MOTOR
GROUND
GRN/YEL
GRN/YEL
GRN/YEL
BLK
BLK
WHT
WHT
WHT
WHT
WHT
86014960
BLK
BLK
VAC MOUNT
GROUND
86014970
3
2
6
3
2
6
4
5
7
5
7
1
8
4
1
8
GRN/YLW
BLK
880420 BLK
880420 BLK
VACUUM
CIRCUIT
BREAKER
PUMP
CIRCUIT
BREAKER
VACUUM
SWITCH
PUMP
SWITCH
VACUUM
MOTOR
CMPS 86290230 04/20/07
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
SERIAL
NOTES:
NO.
PART NO.
PRV NO.
DESCRIPTION
86241930
86256090
86202070
86135320
86028720
86002010
86230210
86001940
86241930
86290270
86290280
86290390
86290400
86290410
47419
730262
360-04B
140687
53266
14942
14832
14635
47419
-
KIT, SQUEEGEE TOOL BLADES
STRAINER, 1/2 FPT 80 MESH
BRUSHES, VAC FOR 116392-00
BRUSH SET, 120V VAC WINDSOR
VAC MOTOR ASM, 115V W/ TERM
BOOT, 3/8 CIRCUIT BREAKER
BREAKER, 6A VDE CIRCUIT
BREAKER, 10A CIRCUIT
KIT, SQUEEGEE TOOL BLADES
MOTOR, 120V CIM-PUMPTEC
PUMP, PUMPTEC, 500PSI
GUN, PRESSURE WASH PMPTC
NOZZLE, ADJUSTABLE HI-LO PMPTC
NOZZLE, REPLACEMENT JET PMPTC
-
-
-
-
CMPS 86290230 04/20/07
5-20
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS- DRY CLEAN OPTION
CMPS 86290230 04/20/07
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS – DRY CLEAN OPTION
SERIAL NO.
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
NOTES:
FROM
1
2
3
4
86236130
86257630
86257700
86286550
34410
02474
02485
47422
1
1
1
FILTER, WET/DRY
TOOL, WHEELED BRUSH
TOOL, DUST BRUSH
KIT, DRY CLEAN
REF
CMPS 86290230 04/20/07
5-22
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS- LOW FLOW SPRAY GUN OPTION
2
1
6
3
4
5
CMPS 86290230 04/20/07
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS – LOW FLOW SPRAY GUN OPTION
SERIAL NO.
REF
PART NO.
PRV NO.
84186
QTY
DESCRIPTION
NOTES:
FROM
1
2
3
4
5
6
86258920
86290390
86005580
86246040
86241690
86041290
1
1
1
1
1
VALVE, FLOW ADJUSTMENT
GUN, PRESSURE WASH
NIPPLE, 1/4 FPT QD
LANCE, SPRAY GUN
JET, 1/ H-VV 8003
56012
51389
44078
47427
REF KIT, LOW FLOW SPRAY GUN
CMPS 86290230 04/20/07
5-24
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS- GROUT CLEANER OPTION
CMPS 86290230 04/20/07
5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS – GROUT CLEANER OPTION
SERIAL NO.
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
NOTES:
FROM
1
2
3
4
5
6
7
8
9
10
11
12
13
86200820
86247720
86194160
86240190
86090230
86241700
86006590
86088740
86230820
86270990
86070460
86276290
86000480
270-11A
56032
11-800133
39639
87015
44079
70088
02476
140653
57090
140652
70626
1
1
1
2
4
2
4
1
2
4
2
4
NIPPLE, 1/8 FPT QD MALE BRASS
NIPPLE, 1/8 CLOSE
TEE, 1/8 BR
HOSE, 1/8 MPT X 1/4 FPT X 12L
WASHER, 9/16 ID X 1.06 OD SS
JET, 1/4 MEG 15015
SCR, 10-32 X 1/2 PPHMS SS NP
TOOL, GROUT CLEANER
BRUSH, FLOOR TOOL
NUT, 10-32 HEX NYLOCK SS
BRKT, BRUSH MOUNT
SCR, #10 X 3/4 PPHST HI-LO BLK
47431
REF KIT, GROUT CLEANER
CMPS 86290230 04/20/07
5-26
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS- HIGH PRESSURE WAND OPTION
CMPS 86290230 04/20/07
5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS – HIGH PRESSURE WAND OPTION
SERIAL NO.
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
NIPPLE, 1/4 FPT QD
HOSE, 1/8 MPT X 1/4 MPT X 7 L
SCR, 10-32 X 1.25 PPHMS SS
VALVE, 500 PSI W/ CLAMP
HOSE, 1/8 MPT X 1/8 MPT X 38L
NIPPLE, 1/8 FPT QD FEM BRASS
TOOL, ALUMINUM WAND
NOTES:
FROM
1
2
3
4
5
6
7
8
9
86005580
86240210
86274410
86258950
86240200
86200810
86257680
86270990
86041300
56012
39641
70195
84189
39640
270-11
02480
57090
47432
1
1
1
1
1
1
1
1
NUT, 10-32 HEX NYLOCK SS
REF KIT, HIGH PRESSURE WAND
CMPS 86290230 04/20/07
5-28
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS- CARPET TOOL OPTION
CMPS 86290230 04/20/07
5-29
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS – CARPET TOOL OPTION
SERIAL NO.
REF
PART NO.
PRV NO. QTY
DESCRIPTION
NOTES:
FROM
1
2
3
4
5
6
86200820
86240220
86197360
86090230
86241710
86284550
270-11A
39642
31016
87015
44080
02484
1
1
1
4
1
-
NIPPLE, 1/8 FPT QD MALE BRASS
HOSE, 1/8 MPT X 1/4 FPT X 12L
ELBOW, 1/4 NPT STREET
WASHER, 9/16 ID X 1.06 OD SS
JET, 1/4 H-VV 11003
TOOL, CARPET CLEANER
SERVICE ONLY
CMPS 86290230 04/20/07
5-30
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE BAG-OPTION
CMPS 86290230 04/20/07
5-31
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE BAG-OPTION
SERIAL NO.
NOTES:
FROM
REF
1
PART NO.
86283390
PRV NO.
47423
QTY
1
DESCRIPTION
KIT, STORAGE BAG
CMPS 86290230 04/20/07
5-32
Download from Www.Somanuals.com. All Manuals Search And Download.
CHEMICAL LOCK-OPTION
CMPS 86290230 04/20/07
5-33
Download from Www.Somanuals.com. All Manuals Search And Download.
CHEMICAL LOCK-OPTION
SERIAL NO.
NOTES:
FROM
REF
1
PART NO.
86070520
PRV NO. QTY
140660
DESCRIPTION
1
BRKT, CHEMICAL LOCK
CMPS 86290230 04/20/07
5-34
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
CMPS 86290230 04/20/07
5-35
Download from Www.Somanuals.com. All Manuals Search And Download.
|