90 Series Blue Universal Thermostat with
Automatic Heat/Cool Changeover Option
Single Stage, Multi-Stage, Heat Pump
Installation and Operating Instructions for Model:
Save these instructions for future use!
Model
Programming Choices
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
CAREFULLYBEFOREINSTALLINGOROPERATINGTHIS
CONTROL COULD CAUSE PERSONAL INJURY AND/OR
PROPERTY DAMAGE.
1F95-1271 Non-Programmable 5/1/1 Day 7 Day
APPLICATIONS
1F95-1271 Touchscreen Thermostat
THERMOSTAT APPLICATION GUIDE
Description
Heat Pump (No Aux. or Emergency Heat)
Heat Pump (with Aux. or Emergency Heat)
Systems with up to 3 Stages Heat, 2 Stages Cool
Heat Only Systems
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Millivolt Heat Only Systems – Floor or Wall Furnaces
Cool Only Systems
Gas or Oil Heat
Electric Furnace
Hydronic (Hot Water) Zone Heat – 2 Wires
Hydronic (Hot Water) Zone Heat – 3 Wires
SPECIFICATIONS
Electrical Rating:
Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . mV to 30 VAC, NEC Class II, 50/60 Hz or DC
Input-Hardwire . . . . . . . . . . . . . . . . . . . . . . . . 20 to 30 VAC
Terminal Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 A per terminal, 2.5A maximum all terminals combined
Setpoint Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 to 99°F (7 to 32°C)
Differential (Single Stage) . . . . . . . . . . . . . . . . . . . Heat 0.6°F; Cool 1.2°F
Differential (Multi-Stage) . . . . . . . . . . . . . . . . . . . . Heat 0.6°F; Cool 1.2°F
Differential (Heat Pump) . . . . . . . . . . . . . . . . . . . . Heat 1.2°F; Cool 1.5°F
Operating Ambient . . . . . . . . . . . . . . . . . . . . . . . . . 32° to +105°F (0 to +41°C)
Operating Humidity . . . . . . . . . . . . . . . . . . . . . . . . 90% non-condensing max.
Shipping Temperature Range . . . . . . . . . . . . . . . . -4 to +150°F (-20 to +65°C)
Dimensions Thermostat . . . . . . . . . . . . . . . . . . . . . 4.6"H x 5.9"W x 1.2"D
ATTENTION: MERCURY NOTICE
This product does not contain mercury. However, this
product may replace a product that contains mercury.
CAUTION
To prevent electrical shock and/or equipment dam-
age, disconnect electric power to system at main fuse
or circuit breaker box until installation is complete.
!
Mercury and products containing mercury must not be
discarded in household trash. Do not touch any spilled
mercury. Wearing non-absorbent gloves, clean up any
spilled mercury and place in a sealed container. For proper
disposal of a product containing mercury or a sealed
container of spilled mercury, place it in a suitable shipping
container and send it to:
Index
Installation
Page
2
2
3
4
6
6
8
Wiring Connections
Thermostat Quick Reference
Installer Configuration Menu
Operating Your Thermostat
Programming
White-Rodgers
2895 Harrison Street
Batesville, AR 72501
Troubleshooting
PART NO. 37-6735A
0544
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMOSTAT QUICK REFERENCE
Home Screen Description
Figure 2 – Home Screen Display
Room Temperature and Setting Temperature
(flashes when compressor is in 5 minute lockout)
Time and Day
System button for selecting
Heat/Off/Cool or Auto (Heat/Cool)
Temperature Up/Down
Displays
indicating the current power
Fan (Auto/On)
level of the 2 "AA" batteries. When the batteries
become low, "Change" will appear with the
The batteries should be replaced at this time.
.
Menu for Cleaning, Programming
and Setting Time
Stage 1
Indicates when thermostat is
calling for Heat or Cool
Figure 3 – Programming & Configuration Items
11
10
Programming and Configuration Items
Displays and "Keypad Lockout" when in keypad
lockout mode.
1
9
Displays and "Temperature Limit" and "Keypad
Lockout" when limited range is activated and locked.
Displays only "Temperature Limit" when limited range
is activated.
1
8
14
2
13
Indicates period of day being programmed.
RUN SCHEDULE (run program) button.
SET TIME button or HOLD temperature button.
12
2
3
4
3
Displays "Change Filter" when the system has run
for the programmed filter time period as a reminder
to change or clean your filter. Displays "Humidifier
Pad" when the system has run for the programmed
filter time period as a reminder to change or clean your
humidifier pad.
5
5
4
7
6
The words "Hold At" are displayed when the thermo-
stat is in the HOLD mode. "Temporary Hold At" is
displayed when the thermostat is in a temporary HOLD
mode.
11
COPY button or INSTALLER CONFIG button.
6
7
CLEAN DISPLAY button allows 30 seconds to wipe off
the display or ADVANCE DAY button for programming.
"Call For Service" indicates a fault in the heating/
cooling system. It does not indicate a fault in the
thermostat.
12
13
14
Used in programming to set time and in configuration
menu to change selections.
8
9
"Stage 1" indicates when heating or cooling stage is
energized. "+2" also indicates when a second stage is
energized.
"Hold Until" indicates the time when a temporary hold
period will end.
"Hours" and "Days" displays during steps in installer
configuration.
10
"Copy" indicates the copy program feature is being
used during programming.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLER/CONFIGURATION MENU
To enter the menu: Press the Menu button. Press and hold for 5 seconds the Installer Config button. This displays menu
item #1 in the table below. Press
to change a menu item.
to advance to the next menu item or
to return to a previous menu item. Press
or
CONFIGURATION MENU
Non-
Displayed
(Factory
Default)
Press
to select from
listed options
or
Menu
Reference
Number
Program- Program- Press
mable
mable
Button
Comments
1
1
MS 2
HP 1, HP 2, SS 1 Selects Multi-Stage (MS 2, No Heat Pump), Heat Pump 1
(HP 1, 1 compressor), Heat Pump 2 (HP 2, 2 compressor
or 2 speed compressor), or Single Stage.
1
2
2
(GAS)
ELE
GAS setting: furnace controls blower.
ELE setting: thermostat controls blower.
Selects programming option.
2
3
4
5
3
* NA
4
Days (7)
PS (4)
5, 0
2
3
4
5
Selects programming steps per day.
Cool Off Cool Off Heat (Emer), Selects system switch configuration for Heat and Cool with
Heat Auto
E (On)
Off Heat, Cool Off Auto changeover, Heat & Cool, Heat Only or Cool Only.
6
7
8
9
* NA
OFF
SL
Selects Energy Management Recovery on or off.
Selects Heat cycle rate Fast (FA) or Slow (SL).
Selects Cool cycle rate Fast (FA) or Slow (SL).
If HP 1 or HP 2 is selected for item #1, selects Emer cycle
rate.
6
7
8
9
5
6
7
Cr Heat (FA)
Cr Cool (FA)
Cr Emer (FA)
SL
SL
10
11
12
8
9
CL (OFF)
dL (On)
0
On
OFF
Selects Compressor lockout ON or OFF.
Selects display light on or off.
10
11
12
10
1, 2, 3, 4 HI
1, 2, 3, 4 LO
°C
Selects temperature display adjustment 1, 2, 3 or 4 degrees
high or low.
(Room temp)
°F
13
14
15
11
12
13
Selects Fahrenheit or Celsius temperature display.
Selects beeper on or off.
13
14
15
b (On)
OFF
Heat (99)
62-99
Selects highest Heat setpoint temperature.
Can select 62° to 99°F.
16
17
18
14
15
16
Cool (45)
45-82
Selects lowest Cool setpoint temperature.
Can select 45° to 82°F.
16
17
18
Keypad
lockout (L)
Keypad
L, P
Selects keypad lockout full or partial to be set.
Temperature Limit Activates temperature limit ranges.
On
000 to 999
OFF
Selects keypad lockout on or off.
lockout (OFF)
000
Selects keypad lockout combination number if lockout is on.
000 is not a valid selection.
19
20
21
17
18
19
FA Heat (On)
FA Cool (On)
If HP or MS selected in item 1, selects Heat Fast second
stage On or Off.
19
20
21
OFF
If HP or MS selected in item 1, selects Cool Fast second
stage On or Off.
000 Change
Filter (OFF)
200 hours
Change
On
Select change filter alert time period.
25 to 1975 hours
On
When set ON, selects time in 25 hour increments.
Selects change humidifier pad alert time period
22
20
22
Humidifier
(OFF)
100 hours
25 to 1975 hours
When set ON, selects time in 25 hour increments.
* Not Applicable
1) This control can be configured for:
3) This control can be configured for 7 independent day or
5/1/1 day programming or non-programmable mode. The
display indicates "7 Days" as default. The programs per
week can be toggled to "5 Days" or "0 Days" by pressing
MS2 – Multi-Stage System (no heat pump)
HP1 – Heat Pump with one stage of compressor
HP2 – Heat Pump with two stage compressor or two
compressor system, Gas or Electric backup
SS1 – Single Stage System
the
or
keys. A selection of 0 Days for non-program-
mable will eliminate the need for EMR, and that step
in the menu will be skipped.
2) GAS or Electric (ELE) fan operation. If the heating system
requires the thermostat to energize the fan, select ELE.
Select GAS if the heating system energizes the fan on a
call for heat. Note: Resetting the thermostat switches
the option to ELE.
4) Programmable Periods – This control can be configured
for 4 or 2 programmable periods per day. The display
indicates "4 PS" in the display as default. The program-
mable periods can be toggled by pressing the
keys.
or
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLER/CONFIGURATION MENU
5) System Switch Configuration – This thermostat is
configured for Heat and Cool with Auto changeover
(SYSTEM switch with Cool Off Heat Auto) default. It can
also be configured for Heat and Cool (Cool Off Heat),
Heat only (Off Heat), and Cool only (Cool Off).
setting is 45°F. It can be changed between 46°F and
82°F by pressing the or key. The "temperature
limit" icon will be displayed to the left of your setpoint
temperature when using this feature. The "temperature
limit" icon will flash if an attempt is made to adjust the
temperature beyond the range selected.
6) Energy Management Recovery – (this step is skipped if
configured to be non-programmable).
17) Keypad Lockout – This step allows you to select the
type of lockout or limited range security required. If no
Energy Management Recovery (E) On causes the
thermostat to start heating or cooling early to make the
building temperature reach the program setpoint at the
time you specify. Heating will start 5 minutes early for
every 1° of temperature required to reach setpoint.
Example: If E On is selected and have your heating pro-
grammed to 65° at night and 70° at 7 AM. If the building
temperature is 65°, the difference between 65° and 70° is
5°. Allowing 5 minutes per degree, the thermostat set-
point will change to 70° at 6:35 AM. Cooling allows
more time per degree, because it takes longer to reach
temperature.
lockout or limited range security is required, press
advance the menu.
Three security settings are available in this menu item.
Use the or keys to select the lockout desired.
Lockout selections are:
"Keypad Lockout and L" = Total Lockout. Total Lockout
locks all keys.
to
"Keypad Lockout and P" = Partial Lockout. Partial Lock-
out allows only the
or
keys to operate within your
set temperature limits.
"Temperature Limit/Keypad Lockout" prevents
changing the temperature limits in the Configuration
Menu.
7, 8 & 9) Cycle Rate Selection – The factory default setting
for Heat is fast cycle (FA Cr), which cycles heat at
approximately 0.6°F. If you prefer slow cycle, press the
18) Keypad Lockout Combination Number Selection
Display will read "OFF" "Keypad Lockout".
Skip this step and continue through the configuration
menu items 19 thru 22 if you require an Air Filter Change
out indicator or Humidifier Pad Change out indicator by
or
key to change to SL. Heat will cycle at approxi-
mately 1.2°F. For Cool the default setting is fast cycle
(FA Cr), which cycles cool at approximately 1.2°F. If you
prefer slow cycle, press the
or
key to change to SL,
pressing the
button to advance.
cool will cycle at approximately 1.7°F. Cycle rate selec-
tion for EMER and Aux is only for HP 1 or HP 2 systems.
10) Select Compressor Lockout CL OFF or ON – Selecting
CL ON will cause the thermostat to wait 5 minutes be-
tween cooling cycles. This is intended to help protect the
compressor from short cycling. Some newer compres-
sors already have a time delay built in and do not require
this feature. Your compressor manufacturer can tell you if
the lockout feature is already present in their system.
When the thermostat compressor time delay occurs, it
will flash the setpoint for up to five minutes.
11) Select Backlight Display – The display backlight
improves display contrast in low lighting conditions.
When the C terminal is powered, selecting backlight (dL
ON) will turn the light on continuously. Selecting backlight
OFF will turn the light on momentarily after any key is
pressed. When the C terminal is not powered, this
selection has no effect.
Return to this point when you are ready to start your
selected lock-out and continue by:
Pressing
Press . Display will read "000".
Pressing or keys to select your keypad lockout
combination number. Note: "000" is not a valid
combination choice.
Record the number you select for future use.
or
keys to select ON.
Press
to exit the menu. The security feature you
select will start in 10 seconds. The system button will
remain active for 10 seconds to allow setting Heat, Off,
Cool or Auto.
19 & 20) Select Fast Second Stage ON or OFF – In the run
mode, with the fast Heat feature enabled (FA Heat On), if
the Heat setpoint temperature is manually raised by 3°F
(2°C) or more above the actual temperature using
second stage will energize immediately. With FA OFF,
the
second stage will not energize until the setpoint tempera-
ture is 1°F or more above actual temperature for more
than ten minutes. The Fast Cool feature (FA Cool)
provides the same controls when the setpoint tempera-
ture is lowered.
12) Select Temperature Display Adjustment 4 LO to 4 HI
Allows you to adjust the room temperature display up to
4° higher or lower. Your thermostat was accurately cali-
brated at the factory, but you have the option to change
the display temperature to match your previous thermo-
stat. The current or adjusted room temperature will be
displayed on the left side of the display.
13) Select F° or C° Readout – Changes the display readout
to Centigrade or Fahrenheit as required.
14) Select Audio Prompting (Beeper) On or Off – Default
setting is On (On b) if you wish to turn off the beeper
select Off b.
21) Select Filter Replacement Run Time – The thermostat
will display "Change Filter" after a set time of blower
operation. This is a reminder to change or clean your air
filter. This time can be set from 25 to 1975 hours in 25
hour increments. A selection of OFF will cancel this
feature. When "Change Filter" is displayed, you can
clear it by pressing Clean Display. In a typical application,
200 hours of run time is approximately 30 days.
22) Select Humidifier Pad Replacement Run Time – The
thermostat will display "Humidifier Pad" after a set time
of heating operation. This is a reminder to change or
clean your humidifier pad. This time can be set from 25
to 1975 hours in 25 hour increments. A selection of OFF
will cancel this feature. When "Humidifier Pad" is
displayed, you can clear it by pressing Clean Display.
Check with your humidifier manufacturer for a recom-
15) Heat Temperature Limit Range – This feature adjusts
the highest setpoint temperature for heat. The default
setting is 99°F. It can be changed between 62°F and
98°F by pressing the
or
key. The "temperature
limit" icon will be displayed to the left of your setpoint
temperature when using this feature. The "temperature
limit" icon will flash if an attempt is made to adjust the
temperature beyond the range selected.
16) Cool Temperature Limit Range – This feature adjusts
the lowest setpoint temperature for cool. The default
mended maintenance interval.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On)
Set the FAN Switch to Auto or On.
Fan Auto is the most commonly selected setting and runs
the fan only when the heating or cooling system is on.
Fan On runs the fan continuously for increased air circulation
or to allow additional air cleaning.
IMPORTANT!
Manual Operation (Bypassing the Program)
Programmable Thermostats
Press
or
and the HOLD button and adjust the tempera-
ture wherever you like. This will override the program. The
HOLD feature bypasses the program and allows you to
adjust the temperature manually, as needed. Whatever
temperature you set in HOLD will be maintained 24 hours a
day, until you manually change the temperature or press Run
Schedule to cancel HOLD and resume the programmed
schedule.
Choose the System Setting
(Heat, Off, Cool, Auto)
Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Program Override (Temporary Override)
Cool: Thermostat controls only the cooling system.
Press
or
buttons to adjust the temperature. This will
Auto: Auto Changeover is used in areas where both heating
and cooling may be required on the same day. AUTO allows
the thermostat to automatically select heating or cooling
depending on the indoor temperature and the selected heat
override the temperature setting for a (default) four hour
override period. The override period can be shortened by
pressing
or lengthened by pressing . Program Override
period can range from 15 minutes to 7 days.
and cool temperatures. When using AUTO, be sure to set the Example: If you turn up the heat during the morning pro-
Cooling temperatures more than 1° Fahrenheit higher than
the heating temperature.
gram, it will be automatically lowered later, when the tempo-
rary hold period ends. To cancel the temporary setting at any
time and return to the program, press Run Schedule.
If the SYSTEM button is pressed to select AUTO the
thermostat will change to Heat or Cool, whichever ran last. If
it switches to heat but you want cool, or it changes to cool
Manual Operation for
Non-Programmable Thermostats
Press the SYSTEM button to select Heat or Cool and use
the
or
buttons to adjust the temperature to your
but you want heat, press both
or
buttons simulta-
desired setting. After selecting your desired settings you can
also press the SYSTEM button to select AUTO to allow
the thermostat to automatically change between Heat and
Cool.
neously to change to the other mode.
PROGRAMMING
Set Current Time and Day
1) Press Menu and then Set Time button once. The display
will show the hour only.
Fill in the blank schedule on the next page then:
Enter the Heating Program
1) Press the Menu button and then press Set Schedule.
Press SYSTEM button to select either "Heat" or "Cool" in
the system switch area indicating the active mode being
programmed. You can switch to the other mode by
pressing the system switch at any time.
2) Press and hold either the
or
key until you reach
the correct hour and AM/PM designation (AM begins at
midnight, PM begins at noon).
3) Press Set Time once again. The display window will show
the minutes only.
4) Press and hold either the
the correct minutes.
5) Press Set Time once again. The display will show the day
of the week.
2) The top of the display will show the day(s) being pro-
grammed. The time and set at temperature are also
displayed. "Morning" will also be displayed to indicate
the period.
or
key until you reach
3) Press
selected temperature for the 1st heating period (Morning).
4) Press or key to adjust the start time for period.
or
key to change the temperature to your
6) Press the
of the week.
or
key until you reach the current day
7) Press Run Schedule once. The display will show the
correct time and room temperature alternately.
5) The time will change in 15 minute increments.
6) After you have set the time and the temperature for the
period to begin, press Set Schedule to advance to the
next program period.
7) Repeat steps 2 through 6 until all of the program times
and temperatures are set for all program periods on
that day.
8) Press "Advance Day" to change to the next day and
repeat steps 2 through 8.
9) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule. The thermostat will now run your program.
Programming Tip: Copy Button
You may copy any daily program to another day or group of
days by pressing the Copy button. In 7 day programming
mode when the Copy button is pressed, the other 6 days of
the week will flash. To copy the current program into the
remaining six days, simply press the Copy button again. To
copy the current program to another day of the week, press
Advance Day to select the day and press Copy to paste the
program. In 5/1/1 day programming mode the copy function
is similar. The weekday (Mon-Fri) program can be copied to
Sat and Sun (both flashing) or use Advance Day to choose
Sat or Sun and press the Copy button to paste the program.
Enter the Cooling Program
1) Press the SYSTEM button until the Cool icon appears.
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING
Energy Saving Factory Pre-Program
The 1F95-1271 thermostats are programmed with the energy saving settings shown in the table below for all days of the
week. If this program suits your needs, simply set the thermostat clock and press the RUN button.
The table below shows the factory set heating and cooling schedule for all days of the week.
* Wake Up
(Morning)
Leave For Work
(Day)
* Return Home
(Evening)
Go To Bed
(Night)
Heating
Program
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
82°F
Cooling
Program
6:00 AM
78°F
8:00 AM
85°F
5:00 PM
78°F
10:00 PM
* You can eliminate these two program periods in the configuration menu (reference #3) if the building is occupied all day.
Day will change to 6:00 am and can be programmed as required.
Planning Your Program – Important
The Heating and Cooling Program schedules below allow you to pencil in your own program times and temperatures.
The 1F95-1271 comes configured for 7 day programming and can also be configured for 5+1+1 programming (see configura-
tion section).
Factory settings are listed on Monday, Saturday and Sunday. If you are re-programming a 5+1+1 day schedule, pencil in your
own times and temperatures directly below the factory times and temperatures.
If you are re-programming a 7 day fill in all lines with the times and temperatures you want.
Keep the following guidelines in mind when planning your program.
• In Heating, lower temperatures will save energy.
• In Cooling, higher temperatures will save energy.
• If you plan on using Auto Changeover, do not program the heating higher than the cooling.
Worksheet for Re-Programming 5+1+1 and 7 Day Program
Heating
Program
Wake Up
(Morning)
Leave For Work
(Day)
Return Home
(Evening)
Go To Bed
(Night)
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
MON
TUE
WED
THU
FRI
6:00 AM
6:00 AM
70°F
70°F
8:00 AM
8:00 AM
62°F
62°F
5:00 PM
5:00 PM
70°F
70°F
10:00 PM
10:00 PM
62°F
62°F
SAT
SUN
Cooling
Program
Wake Up
(Morning)
Leave For Work
(Day)
Return Home
(Evening)
Go To Bed
(Night)
6:00 AM
78°F
8:00 AM
85°F
5:00 PM
78°F
10:00 PM
82°F
MON
TUE
WED
THU
FRI
6:00 AM
6:00 AM
78°F
78°F
8:00 AM
8:00 AM
85°F
85°F
5:00 PM
5:00 PM
78°F
78°F
10:00 PM
10:00 PM
82°F
82°F
SAT
SUN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Reset Operation
Note: When thermostat is reset, installer configuration menu settings and programming will reset to factory settings.
If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by removing
the wires from terminals R and C (do not short them together) and removing batteries for 2 minutes. After resetting the thermostat, replace
the wires and batteries. If the thermostat has been reset and still does not function correctly contact your heating/cooling service person or
place of purchase.
Note: Be sure to review the installer configuration menu settings.
To reset the programming, clock and configuration settings, press
should go blank and then all segments will be displayed momentarily.
and
and the SYSTEM button simultaneously. The thermostat
Possible Cause
Corrective Action
Symptom
1. Blown fuse or tripped circuit breaker.
2. Furnace power switch to OFF.
Replace fuse or reset breaker.
Turn switch to ON.
No Heat/No Cool/No Fan
(common problems)
3. Furnace blower compartment door or
panel loose or not properly installed.
Replace door panel in proper position to engage safety
interlock or door switch.
4. Loose connection to thermostat or system. Tighten connections.
1. Pilot light not lit.
Re-light pilot.
No Heat
2. Furnace Lock-Out Condition. Heat
may also be intermittent.
Many furnaces have safety devices that shut down when a
lock-out condition occurs. If the heat works intermittently
contact the furnace manufacturer or local HVAC service
person for assistance.
3. Heating system requires service or
thermostat requires replacement.
Diagnostic: Set SYSTEM Switch to HEAT and raise the
setpoint above room temperature. Within a few seconds
the thermostat should make a soft click sound. This sound
usually indicates the thermostat is operating properly. If
the thermostat does not click, try the reset operation listed
above. If the thermostat does not click after being reset
contact your heating and cooling service person or place
of purchase for a replacement. If the thermostat clicks,
contact the furnace manufacturer or a HVAC service
person to verify the heating is operating correctly.
1. Cooling system requires service or
thermostat requires replacement.
Same as diagnostic for No Heat condition except set the
thermostat to COOL and lower the setpoint below the
room temperature. There may be up to a five minute delay
before the thermostat clicks in Cooling.
No Cool
1. Possible short in wiring.
Check each wire connection to verify they are not shorted
or touching together. No bare wire should stick out from
under terminal block. Try resetting the thermostat as
described above. If the condition persists the manufacturer
of your system or service person can instruct you on how
to test the Heat/Cool system for correct operation. If the
system operates correctly, replace the thermostat.
Heat, Cool or Fan
Runs Constantly
2. Possible short in thermostat.
3. Possible short in heat/cool/fan system.
4. FAN Switch set to Fan ON.
1. Thermostat thermometer setting
requires adjustment.
The thermometer can be adjusted +/- 4 degrees. See
Temperature Display Adjustment in the Configuration
Menu section.
Thermostat Setting &
Thermostat Thermometer
Disagree
1. The location of the thermostat and/or
the size of the Heating System may
be influencing the cycle rate.
Digital thermostats provide precise control and cycle faster
than older mechanical models. The system turns on and
off more frequently but runs for a shorter time so there is
no increase in energy use. If you would like an increased
cycle time, choose SL for slow cycle in the Configuration
menu, step 6 (heat) or 7 (cool). If an acceptable cycle rate
is not achieved, contact a local HVAC service person for
additional suggestions.
Furnace (Air Conditioner)
Cycles Too Fast or Too Slow
(narrow or wide
temperature swing)
Press the menu button (button will disappear) and hold in
for 20 seconds. This unlocks the thermostat.
Forgot Keypad
Lockout Code
HOMEOWNER HELP LINE: 1-800-284-2925
White-Rodgers is a division
of Emerson Electric Co.
The Emerson logo is a
trademark and service mark
of Emerson Electric Co.
St. Louis, Missouri
Download from Www.Somanuals.com. All Manuals Search And Download.
|