DIAMOND PRO
OPERATING MANUAL
DIAMOND 8.1 PRO
DIAMOND 8.2 PRO
DIAMOND 8.1 PRO ACTIVE
DIAMOND 8.2 PRO ACTIVE
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents:
Page 1:
Using your Reference Monitor
Use of a subwoofer
Page 2:
Page 3:
Use with CRT displays
5.1 Monitoring
Stereo Near Field Monitoring Set-up
5.1 Set-up
Equalisation
System
Drivers
Page 4:
Crossover
Cables and Connections
A/C Connection
Amplifier/s
Installation and Application
Positioning and Mounting
Page 5:
Page 6:
Page 7:
EQ-LF
Bass Filter
Portrait or Horizontal Mounting
Console Top Mounting
Stand Mounting
Center speaker Mounting and Positioning
Controls and Indicators: Rear and Front Panel
Volume Control
Technical Specifications and Data
Maintenance
Safety
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Wharfedale Diamond 8.1 Pro, 8.2 Pro and Pro-Active Near Field Reference Monitors
The function of a Reference Monitor Loudspeaker System is to provide an accurate sonic
reference for the operator/engineer thus enabling value decisions to be made in the recording
and mixing process. The purpose of these devices is not simply to sound exciting, or
impressive - only to give an accurate and clean representation of the original sources and
recording devices used. This must be done with the minimum destructive interaction with the
room and consistently in a variety of environments. It is also essential that the Reference
Monitor does not favor or exaggerate any part of the spectrum, but gives the engineer a
reference for the real-world environment in which the program will be played and heard by the
general public.
Using your Reference Monitor
The Diamond Pro and Pro-Active Near Field Reference Monitor Loudspeaker Systems are
accurate, low distortion, high quality, self amplified (Pro-Active version only) loudspeaker
systems designed and optimized for recording and reference monitoring. In this application
quantitative and qualitative decisions are made by the operator based upon many factors, all
dependant on what is heard from the loudspeaker used as a monitor. For accurate decisions
to be made at the time of recording in such areas as microphone choice, position, level and
ambient space-positioning, and at mix-down, for level, eq, effects and spacial placement, the
engineer must have reference source loudspeakers that are smooth and neutral, image
accurately, have as low distortion as possible, and dynamic stability throughout the operating
envelope.
The Diamond Pro and Pro-Active are designed understanding all these requirements, and
perform exceptionally well in all aspects. You are encouraged to listen to favorite program
materials and to compare the quality and balance to your current monitors. Mix down from
recordings you have already made and listen to the results on the Diamonds as well as in your
car, or on your home stereo system. It is important that an understanding of the entire
recording process is gained through reference to these monitors and how the results of
recording and mixing on these work in the “real world.” We are confident you will find these
speakers not only revealing and transparent, but musical and involving. We hope through their
revealing nature they will encourage more analytical thought in the choice and placement of
microphones and the set-up and mapping and spatial character of your mix. This is true both
for two channel (stereo) as it is in mixing for 5.1 multi-channel applications.
Use of a subwoofer
Where possible it is strongly recommended that monitoring and mixing is done on a full range
speaker, if possible, without the use of a sub woofer. Some caution must be exercised
however. Full range, means covering the whole audible frequency spectrum. Nominally this is
accepted as being 20-20kHz. Your Diamond reference monitors, whilst giving an unusually
extended low frequency response, do not go down to 20Hz. A properly installed, appropriately
crossed over and well performing sub can be very valuable in the mixing and dubbing process.
The proper set-up of a sub woofer and bass management in general is not a simple process.
Anomalies in the monitoring system tend to turn up as the inverse in the mix. Placement is
critical. Given the bass management is done properly and the main speakers are set-up well,
a subwoofer placed randomly in a control room could cause major problems. For example, the
engineer could be sitting at a low frequency “null” or hole in the response. Sub woofers oper-
ating at 50Hz or lower are generating very long wavelengths. For example, at 40 Hz, the
1
Download from Www.Somanuals.com. All Manuals Search And Download.
wavelength is around 28ft (8.5m). It is quite possible that at these wavelengths from a single
source/woofer both your ears could be in a phase hole. The room may be rattling and shaking,
but you would not hear the direct sound only its effect on the space. The opposite is also true.
The room and woofer interaction could generate a standing wave that would give up to 6dB of
build up at your ears. Thus great care should be taken in placement to find the best location
for the speaker. If possible two sub woofers of the same type should be placed asymmetrical-
ly in the control room. You should also take into account the construction of the walls, floor
and ceiling of the control room. . One way to hear how much you are losing is to play some
good full range program and walk outside the control room. With the door closed, how much
low frequency energy are you hearing leaking out? Is this desirable? Probably not, since it will
annoy co-workers and neighbors and is costing you power and headroom in your system!
Overall the best advice is to take care and time with your subwoofer placement and integration
to the room and main channels. Do not simply position the subwoofer without due thought
and be impressed with the sound and power. If you are setting up a monitoring system, it is
critical that the sub is placed and integrated correctly or your product – your mix will suffer. It
is suggested that three of four popular DVD’s are auditioned with and without a sub in the sys-
tem. You will find that often there are great differences in the amount of low frequency content
on the tracks. For best results, use a reference disc with a response sweep up to 800Hz.
Use with CRT displays.
The Diamond Pro and Pro Active reference monitors are magnetically shielded for use in close
proximity to CRT displays as are found in many of today’s production and dubbing systems so
placement next to CRT monitor displays are possible.
5.1 Monitoring
It is strongly recommended that for 5.1 Multi-channel monitoring, all 5 of the main channels
should be the same loudspeaker. Critically, the three main “screen channels” should be the
same, i.e. have the same sonic character and coverage. In a perfect world consumer 5.1
playback systems would also have the Left, Center, and Right channels all the same speaker.
It is important that professionals involved in source creation use the proper set-up and follow
recommended practices for speaker placement and balance. This way your product – the
recording, will playback properly on all types of replay system, both cinema, home theatre, car
and other.
Note: There are some variables found in these replay systems to be taken into account of in
the monitoring environment. There are also different practices used in the creation and mixing
of program materials. Stereo, 5.1, DVD-Audio etc can be quite different.
For home cinema and motion picture exhibition the monitor levels and balance can generally
be set-up with the Left, Center and Right “screen” channels having the same level. The Left
and Right Surrounds are generally considered to be best when their summed output equals
one of the screen channels. In other words, each of the surrounds is 3dB below any of the
screen channels. This can vary in the real world where often all 5 of the main screen and
surrounds are set at the same level.
Stereo Near Field Monitoring set-up:
Placement should be as much as possible for you and the two speakers to make the three
corners of an equilateral triangle. The typical distance your head will be from (plus or minus
reasonable movement back and forth) from the speaker position line, will dictate the width
through some simple math, or experimentation. This places the speakers at 60 degrees.
Vertical set-up should allow the speaker central axis to point at head height. The Diamond is a
well designed speaker that is relatively insensitive to the height of the listener. However, a
2
Download from Www.Somanuals.com. All Manuals Search And Download.
nominal central aim point is recommended. Again, experiment and find a comfortable median
position. Height placement should ideally not be from below, nor typically too high. Be
sensitive to early reflections from control surfaces. Careful placement can reduce the
destructive effects of reflections, diffraction etc. Be aware of placements that can excite cavity
resonances, and look for symmetry from left to right and across the main three screen
channels.
5.1 set-up:
The Left and Right monitors should be placed at 30 degrees either side of the center line of
the set up. The rears should be placed at 110 degrees either side of this line.
The center should be the same distance from the central monitoring point as the left and right
channels. This can be achieved through time delay in many processors or through set-up
where possible. Levels to all channels should be either identical, or with the Left and Right
Surround Channels down set 3dB.
Equalisation:
Whether you have the skills or experience of equipment, it is still essential that EQ is used as
a last resort, or as “icing on the cake” only. Take great care in the set-up and balance of your
systems. Check all levels and placements. Fix flutter echoes, nulls/suck outs, and reso-
nances at source. Then when the system is well integrated to the environment, consider EQ.
Fix acoustic problems acoustically, and electrical problems electrically! Reflections should be
tamed at source and not compensated destructively with an equalizer! Similarly resonances
should be hunted down and cured at source. Take time, listen, look and analyze.
For these reasons, we do not generally recommend the equalization of monitoring systems.
So called “Room EQ” is considerably less necessary with a good Near Field Monitoring (NFM)
system. Since the whole principle of NFM is to remove the influence of room interactions
through the placement of speakers close to the monitoring position, and thus the timing and
level relationship of originating signal to any room reflections allows our built-in psycho-
acoustic processing to “ignore” much of the room effect. Our standard, built-in Human
Psycho-acoustic processor is extremely powerful, and is able to naturally ignore late arriving
signals in favor of the originating source within certain time envelopes. These are generally
15ms and 10-15dB. In NFM applications the close proximity of the speakers means that any
room returns are late, thus ignored! We designed the Diamond Pro to be a naturally balanced
product, with smooth, low Q, changes in radiation pattern over its operating range. All the
transducers were purpose built and integrated into the design as integral parts. The natural
balance of the speaker is such that EQ is detrimental.
System:
The Diamond Pro is a “full range” two way direct radiating, ported loudspeaker system in a
compact and well damped enclosure. All components are specifically design for this system.
The Pro-Active model is a bi-amplified with an active crossover. All components were
designed for optimum performance as a system. Magnetic shielding is provided on the trans-
ducers to allow their use in close proximity to CRT displays.
Drivers:
The Diamond Pro driver complement consists of a 1” or 25mm soft dome high frequency driv-
er, and a 127mm woofer. The woofer uses a sophisticated Kevlar® cone material specially
formed to give exceptional rigidity yet low mass. The extreme “bulletproof” strength of Kevlar®
gives excellent low frequency stiffness for long excursions under very high drive levels from
the voice coil, yet at the same time its low mass means the cone can remain truly pistonic at
extended frequencies. Normal cones are a compromised through being made light in weight to
3
Download from Www.Somanuals.com. All Manuals Search And Download.
make the higher frequencies at crossover, but their light weight means the cone can break up
when asked to stop and start over 4,000 times a second at typical crossover frequencies, with
resultant “cone cry”,
Crossover:
8.1 Pro: internal passive crossover, 2.2kHz
8.1 Pro: internal passive crossover, 2.0kHz
8.1 Pro-Active: internal active crossover, 2.0kHz
8.2 Pro-Active: internal active crossover, 1.9kHz
The inherent quality and correctness of the design of the Diamond components means that
simple and elegant crossover designs can be used. The lack of cone break up at high fre-
quencies means that steep and complex crossovers with their inherent phase distortions are
avoided. Both the Active and the passive versions of the Diamond Pro are essentially the
same. The crossover in the active model is at a slightly lower frequency allowing subtle
improvement in vertical integration and stability of image and sonic character.
Cables and Connections:
Always use high quality cables and connectors in hooking up audio equipment, especially in
speaker connection where higher current is likely to be seen. There are a number of high qual-
ity cables available on the market that give measurably better performance whether in low
level signal, or high current voice coil level use. Connectors should be of high quality wherev-
er possible. The Diamond Pro passive monitor features a Neutrik Speakon ™ type connec-
tion. This type of connector is specifically designed to give low resistance, high quality connec-
tion with bare metal wiping contacts.
On the Diamond Pro-Active we recommend using the XLR type connector where possible for
superior security of connection and better contact.
A/C Connection.
Make sure your power is clean and properly grounded. Experience shows that superior
sound quality can be attained through the use of “stiff” A/C power circuitry. Short runs of good
conductor diameter cabling. For high level usage take the time to monitor your power voltage.
Poor A/C wiring to the studio will show the voltage dropping momentarily during high power
transients. The effect of poor A/C distribution in your studio can be heard as soft or weak bass
and often noisy and hum through poor grounding.
Amplifier/s:
The Diamond Pro-Active has two independent power amplifiers built in -designated and opti-
mized for each of the specific duties. The low frequency amplifier is designed to output 60
Watts RMS to match the woofer. The high frequency power amplifier outputs 40 Watts. Both
amplifiers are carefully designed to provide enhanced headroom with extremely graceful over-
load characteristics. The net effect of the holistic nature of the design of each amplifier com-
bined with its paired driver is apparent and usable output is well beyond the power levels
implied in the specifications.
Installation and Application
Position & Mounting:
The Diamond Pro passive monitor is front ported to allow positioning close to the wall. Two or
three inches/50-75mm clearance is sufficient to allow normal operation.
The Diamond Pro-Active has the input and power connections on the rear, but most
4
Download from Www.Somanuals.com. All Manuals Search And Download.
importantly the heat sink assembly. Make sure the heat sink has sufficient clearance to allow
reasonable airflow. This will, to some extent, be dependant on the power levels and duty
cycles under which one is operating the system.
EQ-LF:
In the real world, as opposed to the theoretical, loudspeakers operate and interact with the
space in which they are used. It is important to understand the low frequency reinforcement
that occurs as a result of the relationship of the speaker to walls etc. At the lower frequencies
(and therefore longer wavelengths), loudspeakers are typically less and less directional. The
smaller the speaker enclosure and the smaller the woofer (typically the higher the frequency)
the system becomes 360 degree radiating. The net effect is that the low frequencies get boost-
ed more and more when we place a speaker against a wall, or on a desktop.
Bass Filter:
The most important thing to understand is the need to compensate for this potential build up,
in the most simple and elegant way. On the rear panel of your Diamond Pro-Active you will see
a switch marked “Bass Filter”. This is carefully and specifically designed to control the typical
low frequency build-up caused by the speaker’s interaction with the room/space. The Bass
Filter is a simple and graceful 6dB per octave filter that cuts the bass energy progressively at
the same rate as the loudspeaker directs energy to a wider angle. Look at the application and
think of the walls or desktop in terms or a low frequency mirror affecting the bass spectrum. If
you believe you are likely to get considerable low frequency boosting it is recommended that
you use the bass filter. Again, experimentation is important. Remember: Too much bass out
put in your monitor will likely cause you to reduce the amount of energy in the low frequencies
that you place on tape or on to your recording medium. Too little lows in your monitor with
create the opposite effect. Listen and experiment. Use program material you are familiar with
and “play” with the positions and settings to get the best you can.
Portrait or Horizontal Mounting:
The preferable method of mounting a two way loudspeaker is in the vertical. This is typically
because our ears on on the sides of our head and thus we are more sensitive to horizontal
position and relationships. The positional offset of the drivers when the speaker is mounted
horizontally can result in a phase hole in the response when the listener is offset from the
centerline. The Diamond Pro is an exceptionally bfry loudspeakercan gardngs tiecte verticee
horizontdB pe fmaranc monfarnd lessusexceprabld to thisrorabm,n (wlieter)55.,ng it iooswilee
Stand Mounting:
Depending on the application stand mounting in (near to) free space is one of the most neutral
positions for monitors. Of course it is not always possible to take advantage of the isoalation
from floor, wall and countertop effects that stands can allow. But combinations of short stand
and console can be used to advantage.
Center Speaker Mounting and Positioning:
Ideally the center speaker is just that; mounted in the center! However, the type and size of
display can seriously effect one’s options for position. The shielding of the Diamond Pro
allows it to be placed close to and either over or under the CRT display. Plasma, projection,
rear projection etc. all offer different advantages and options. The closer one is to the monitor,
the more critical the angles become. At a reasonable distance the imaging and integration of a
speaker is improved when compared to being very close. Experimentation will establish the
best distance and position when based upon a reasonable understanding of the requirements
and standards.
Controls & Indicators: Rear Panel
4
5
1
3
2
6
1. Volume Control: Adjusts the input level to the internal amplifiers.
2: Power On/Off Switch
3. Input 1 Balanced
4. Input 2 Unbalanced
5. Bass Filter Switch: Flat or Cut
6. AC Input
6
Download from Www.Somanuals.com. All Manuals Search And Download.
8.1 Pro
8.2 Pro
Models
Type
2 WAY
2 WAY
Usable frequency response
Peak SPL @ 1m, short term IEC noise source 106dB
50Hz-24kHz
45Hz-24kHz
108dB
Sensitivity
86dB
86dB
Power Handling (Watts)
Recommended amp power
Impedance nominal
Drive Units
System Magnetic Shielding
Crossover frequency
Input connectors
100 W
30-150W
4Ω
5"LF, 1" HF
Yes
100 W
30-200W
4Ω
6.5" LF, 1" HF
Yes
2.2K
2.2K
1 x phono speakon type /jack combo
Input connectors (active)
Active ie slew rate, distortion
Finish
Dimensions H x W x D (mm)
Dimensions of Active H x W x D (mm)
Weight (each kg)
1 x phono (unbalanced)
10v/micro s
IRIDIUM color laminate
295 x 198 x 252
295 x 198 x 280
5.2kg
1 x XLR-1/4 jack combo balanced
10v/ micro s
IRIDIUM color laminate
364 x 212 x 257
364 x 212 x 322
6.2kg
Weight of active unit (each kg)
7.5kg
8.0kg
Active units only:
Usable frequency range
Drive units
Crossover frequency
Output SPL ((from peak power)
IEC weighted noise @ 1m)
Bi-amplifier power (LF/HF)
Input sensitivity
Amplifier system distortion at
System Magnetic Shielding
Signal to noise ratio
Mains voltage:
50Hz-24kHz
5" LF, 1" HF
2.0K
45Hz-24kHz
6.5" LF, 1" HF
1.9K
106dB
108dB
60W LF + 40W HF
0.775V RMS (0 dBu)
0.1% @ 50W
Yes
60W LF + 40W HF
0.775V RMS (0 dBu)
0.1% @ 50W
Yes
100dB
100dB
Voltage operating range at:
230V setting
115V setting
205-250V
100-130V
205-250V
100-130V
Power consumption:
Idle
22W
22W
Full output
130W
130W
Maintenance:
The high quality finish on your Diamond Pro is generally not in need of any care or
attention. Do not use abrasives or abrasive materials to clean the enclosure since the
finish may be marred. Never use water on or near electrical equipment.
The Diamond Pro-Active heat sink must be checked for clearance from obstructions,
lint – fluff or anything that might cause overheating.
Safety:
Always use grounded A/C power. Take care to mount and operate your equipment in a
safe manner. Avoid exposure to rain and water.
Accessories:
Diamond Pro Series Subwoofer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond 8.1 Pro Active free air
with/without bass cut
Diamond 8.2 Pro Active free air
with/without bass cut.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WHARFEDALE PROFESSIONAL
IAG HOUSE, SOVEREIGN COURT, ERMINE BUSINESS PARK, HUNTINGDON, PE29 6XU, UK
911.388
Download from Www.Somanuals.com. All Manuals Search And Download.
|