USER’S MANUAL
LTV-27w6 HD & LTV-32w3 HD
Widescreen HDTV
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PRODUCT SAFETY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Safety Guidelines
PRODUCT SAFETY
WARNING: This device must be operated with the original power supply, part number DPS-210 EP 2 C.
CAUTION: The power supply outlet should be located near High Definition LCD TV and should be easily
accessible. Always use the appropriate AC cord that is certified for your specific country. Some examples
are listed below:
USA..................UL
Canada.............CSA
Germany..........VDE
Switzerland ..... SEV
Britain ............. BASE/BS
Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The specific power cord for this High Definition LCD TV is enclosed and has been selected according to the
country of destination and must be used to prevent electric shock. Use the following guidelines if it is
necessary to replace the original cord set, or if the cord set is not enclosed. The female receptacle of the
cord set must meet IEC-60320 requirements and should look like Figure A1 below:
Figure A1
Figure A2
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For High Definition LCD TVs that are placed on a desk or table, type SVT or SJT cord sets may be
used. For High Definition LCD TVs placed directly on the floor, only SJT type cord sets may be used. The
cord set must be selected according to the current rating for the High Definition LCD TV. Please consult the
table below for the selection criteria for power cords used in the United States and Canada.
Cord Type
Size of Conductors in Cord Maximum Current Rating of Unit
SJT
18 AWG
16 AWG
14 AWG
18 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
SVT
FCC Compliance Statement
This equipment has been tested and complies with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and may
cause harmful interference to radio communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
x
x
x
Reorient or relocate the receiving antenna.
Increase the separation between the High Definition LCD TV and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
x
Consult the Westinghouse Service Center or an experienced radio/TV technician for assistance.
FCC Warning
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. If a BNC cable used, use only a
shielded BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by
Westinghouse Digital will void the user's authority to operate this device.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Product Safety Instructions
PRODUCT SAFETY
Follow and obey all warnings and instructions marked on the High Definition LCD TV. For
your safety, please read all the safety and operating instructions before you operate the
High Definition LCD TV. Keep this user’s manual for future reference.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to a void injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Other Notices
x Avoid exposing the High Definition LCD TV to direct sunlight or high temperatures.
x Avoid exposing the High Definition LCD TV to moisture or high humidity
x Do not attempt repairs yourself. Your warranty does not cover repairs or attempted
repairs by anyone not authorized by the manufacturer
x If your High Definition LCD TV will not be used for a long period of time, unplug the
High Definition LCD TV and remove the batteries from the remote control
x Only use attachments/accessories specified by the manufacturer.
x Avoid touching the screen. Skin oils are difficult to remove.
x Never remove the rear cover. Your High Definition LCD TV contains high-voltage
parts. You may be seriously injured if you touch them.
x Always handle your LCD display with care when moving it.
x If the High Definition LCD TV emits smoke, abnormal noise, or a strange odor,
immediately turn it off and contact the Westinghouse Service Center.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Antenna Installation Safety
PRODUCT SAFETY
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the High Definition LCD TV, be sure the
antenna or cable system is grounded to prevent voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANS/NFPA 70, provides information on proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
Lightning
For added protection for the High Definition LCD TV during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the High Definition LCD TV due to lightning
and power-line surges. Do not disconnect the antenna or the power cord during a heavy storm –
lightning may strike while you are holding the cable cord, causing serious injury. Turn off your High
Definition LCD TV and wait for the weather to improve.
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits. When installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2
What Is Digital Television?
A GUIDE TO DIGITAL TELEVISION
Digital television is a new way of transmitting high quality video and audio to your
TV set. Using digital television, broadcasters can transmit high definition TV (HDTV)
images. This High Definition LCD TV has a built-in digital television tuner. The advantage
of an integrated digital television set is that it can tune both analog and digital TV channels.
All you'll need to do is to add an external antenna and you are ready to watch digital
television.
Digital Television Picture
Digital television programs are transmitted in two different formats. The first is Standard
Definition Television (SDTV) and the second is High Definition Television (HDTV).
SDTV program formats include 480-line interlaced (480i) and 480-line progressive (480p)
video. 480i programs are essentially a digital version of our current analog TV programs,
while the 480p format offers improved image detail over 480i. Some 480p programs are
broadcast in widescreen and are comparable to progressive-scan DVD movies in image
quality.
HDTV and standard definition television (SDTV) are the two categories of display formats
for digital television transmissions. HDTV provides a higher quality display with a vertical
resolution display of 720p or 1080i. The “p” stands for progressive scanning, which means
that each scan shows every line for a complete picture at 1/60th of a second. The “i” stands
for interlaced scanning which first shows every odd line at one scan of the screen and then
follows with every even line in the second scan for a complete picture at 1/30th of a second.
Both HDTV formats are always broadcast in widescreen, and both offer much higher
picture quality than SDTV.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2
A Guide to Digital Channels
A GUIDE TO DIGITAL TELEVISION
There is a new numbering system for digital channels. Digital television virtual channels
consist of a number followed by a dash and then another number. The first number is the
major channel number specific to a broadcasting station. The second number is the minor
channel number that allows these broadcasting stations to use the same major channel
number for all analog and digital channels because digital channels can carry multiple
programs simultaneously. The old analog channels are always referenced to minor
channel number 0, for example 11-0.
Digital Virtual Channel Number
Physical Channel Number
The channel number in parentheses represents the actual physical channel number of the
transmitter used to broadcast the network programming in your region. Each physical
channel number is mapped to one or more digital channel numbers. In the example above,
digital channel number 11-1 is mapped to physical Channel 12 and tunes into channel 12.
Some digital television stations may have only one virtual channel, others perhaps as
many as six. So in the example above, the station using physical Channel 12 for digital
television can have additional digital channels 11-2, 11-3, etc.
How to input digital television channels:
User Inputs
Channel Displayed
Channel 11 – 3
Channel 11 – 3
Method 1: 11 – 3
Method 2: 113
For single digit channels:
User Inputs
Method 3: 052
Channel Displayed
Channel 5 – 2
Channel 5 – 2
Method 4: 5-2 + Ent
Check your local listings for available digital television channels in your area.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
The Electronic Program Guide
A GUIDE TO DIGITAL TELEVISION
Your Westinghouse High Definition LCD TV has an Electronic Program Guide (EPG) to
help you navigate through all the possible viewing options. The EPG supplies information,
such as program lists, the start and end times of all available channels, and a detailed
description of the program. The availability and the amount of program details will vary
depending on the broadcaster. You can use the ‘Guide’ button on the remote control or
select EPG from the TV OSD menu to display the Electronic Program Guide. The EPG
begins its list with the channel that is currently active.
1. Channel Number
Shows the current physical channel number and all the available virtual channels.
2. Program Time
Displays the program start and end times.
3. Abstract
Displays detailed information for the selected digital program. The availability of detailed
information depends on the broadcaster.
4. Current Time and Date
Shows the current time and date.
5. Event Titles
Displays the title of upcoming programs.
6. Help Instructions
List of available commands while in the Electronic Program Guide.
x
Use the arrow keys and the Channel up/down buttons on the remote control to scroll
through the Electronic Program Guide.
x
Press Enter (the Enter) button on the remote to step into a sub section or press Back
(the Last Channel) button on the remote to step back a section.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Package Contents
INSTALLATION
Your product package includes:
x 27” or 32” Westinghouse High Definition LCD TV
x Remote Control (with batteries)
x Power Cord
x User’s Manual
x Warranty Card
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Front View of the High Definition LCD TV
INSTALLATION
Use the buttons on the right side of the High Definition LCD TV or the buttons on the
remote control to display the On Screen Display (OSD) menu and adjust the High
Definition LCD TV options. The OSD controls are defined in “OSD Functions” on page 16.
LED indicator
“IR” receiver
Speakers
Rear View of the High Definition LCD TV
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Side View of the High Definition LCD TV
INSTALLATION
1. Menu
Turn OSD Menu ON/OFF
Increase/Decrease sound volume or adjust
a highlighted control while in OSD Menu
2. Volume + / -
3. Channel S / T
4. Source
Channel up/down when source is TV or
select a control while in OSD Menu
Select Active Video source or a highlighted
control while in OSD MENU
5. Power Button
Power ON/OFF
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3
INSTALLATION
SIDE CONNECTORS
1. YPbPr2 / Audio2 (Right / Left)
Connect the component video to an external video device
such as a DVD or gaming system.
2. YPbPr1 / Audio1 (Right / Left)
Connect the component video to an external video device
such as a DVD or gaming system.
3. S-Video
Connect to an external video device such as a VCR. Audio
(R/L) input supports either S-Video or AV input.
4. AV Video / Audio (Right / Left)
Connect the composite video to an external video device
such as a VCR. Audio (R/L) input supports either S-Video or
AV input.
5. DVI-HDCP / Audio (Right / Left)
Connect to an external DVI-HDCP device such as a DVD,
cable/satellite receiver, or computer.
6. HDMI / Audio (Right / Left)
Connect to an external HDMI device such as a DVD or
cable/satellite receiver. To use analog audio for HDMI, open
the OSD menu, and under the Audio menu, use the left/right
arrow key to change HDMI to Analog.
7. Audio Out (Right / Left)
Connect this output to an external audio amplifier.
8. Audio-In (VGA)
Using a 3.5mm mini-jack cable, connect to the Audio out
(Green) on a computer.
9. VGA
Using a 15-pin VGA cable, connect to a computer.
10. Service Port
Factory use only.
11. ANT (RF-input)
Connect to the antenna or cable service.
12. AC-IN (Power)
Connect the power cord from AC-IN to a power source.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Remote Control
INSTALLATION
Use the Remote Control to adjust your Westinghouse High Definition LCD TV.
1. POWER
Switch the power On/Off
2. PIP
Display sub picture On/Off
3. MUTE
Turn the sound On/Off
4. SWAP
Switch between PIP and Main Picture
5. BACKLIGHT
Shortcut to adjust backlight adjustment
6. CC
Turn Closed Caption On/Off
7. SLEEP
Set sleep timer
8. FAVORITE CHANNEL A / B / C
Jump to favorite channels (Hold button for
3 seconds to program favorite channel).
9. CHANNEL NUMBER KEYS
Select specific channels
10.DASH
To input dash when selecting specific
channels
11.ENT
Complete channel selection
12.INPUT
22.YPbPr1
Switch to YPbPr1 source
23.PC
Switch to VGA source
24.HDMI
Switch to HDMI source
25.TV
Switch to TV source
26.YPbPr2
Switch to YPbPr2 source
27.AV
Switch to AV source
28.S-VIDEO
Switch to S-Video source
29.DVI
Switch to DVI source
1
2
3
4
7
5
6
8
Display MP input menu (see page 30)
13.VOL - / +
9
Volume Up/Down adjustment
14.SCALING
Set video display format to
“STANDARD” or “FILL”
15.CH T / S
TV Channel Up/Down adjustment
16.MENU
Turn OSD Menu On/Off
17.LAST CHANNEL
Switch to previous channel
18.T / S / W / X
10
12
13
14
16
11
15
17
19
18
20
22
23
26
27
21
25
24
29
28
Navigate within OSD Menu
19.ENTER
Make a selection
20.EPG
Display Electronic Program Guide
21.INFO
Display the source and channel information
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installation
INSTALLATION
ʳ
1. Insert Remote Control Batteries
1) Remove the battery cover.
2) Insert the batteries corresponding to the (+) and (í) marks on the battery
compartment.
3) Re-attach the battery cover.
CAUTION:
x Only use AAA batteries.
x Do not mix new and old batteries. This may result in cracking or leakage, which may pose a
fire risk or lead to personal injury.
x Insert batteries according to (+) and (í) markings. Inserting the batteries incorrectly may
result in cracking or leakage, which may pose a fire risk or lead to personal injury.
x Dispose of used batteries in accordance with local laws and regulations.
x Keep batteries away from children and pets.
x When the remote control will not be used for an extended period, remove the batteries.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3
2. Connect the High Definition LCD TV to a computer
INSTALLATION
Connect a VGA or DVI cable and an audio cable to the back of the High Definition LCD TV.
IMPORTANT: Before you begin, make sure all devices are turned off.
VGA CONNECTION: Connect an analog VGA cable from your computer VGA OUT
port to the High Definition LCD TV VGA IN port.
DVI-D CONNECTION: Connect a Digital DVI cable from your computer to the High
Definition LCD TV DVI-D port.
AUDIO CONNECTION: Connect a stereo mini cable from the computer’s AUDIO
OUT port to the AUDIO IN port on the High Definition LCD TV.
3. Connect the High Definition LCD TV to AV Devices
Connect one or all of the following compatible devices into the back of the High
Definition LCD TV.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4. Connect power cable and power on the High Definition LCD TV
INSTALLATION
Connect the power cord to the High Definition LCD TV then to a properly grounded AC
outlet and press power to turn on the High Definition LCD TV.
NOTE: The High Definition LCD TV will take a few seconds to power up.
5. Turn on your computer
The High Definition LCD TV will auto adjust to the resolution of the computer.
6. Turn on the cable box or satellite receiver
If using DVI or HDMI connection, the cable box or satellite receiver will need to be
restarted to complete HDCP authentication to view the picture.
7. Select an input source for the High Definition LCD TV using the OSD
menu or remote control
8. If connecting to an Antenna, Cable or other RF source, run Autoscan
to receive all available channels:
1. Press the ‘Menu’ key on the remote or side panel and use the left/right arrow keys
to select the TV menu.
2. Use the up/down arrow keys to select “Tuner Source”.
3. Use the arrow keys to select your signal source “Air/Cable/IRC/HRC”.
4. After selecting your signal source, use the up/down arrow keys to select “Auto
Scan”. Press “Enter” to start scanning for channels.
5. This will take a few minutes to identify analog and digital channels.
9. If connecting to a computer:
For the best picture quality, set PC timing mode to VESA* 1366x768 at 60Hz. Refer to
your computer’s graphic card user guide for questions on how to set this timing mode.
Many computers show 1360x768 as an alternative resolution.
* VESA is a trademark of Video Electronics Standards Association. All other trademarks
are the property of their respective owners.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4
OSD Function
OSD FUNCTION
To display the OSD main menu, press the Menu button on the right side of the High
Definition LCD TV or the MENU key on the remote control. Use the ꢀ/ꢁ arrow keys to
highlight the desired OSD Main Menu.
Main Menu
To select a sub-menu, press ϧ/ϰ on the right side of the High Definition LCD TV or the
ϧ˂ϰʳ key on the remote control.
OSD Main Menu
OSD Sub-Menu
List of functions under main menu
Help Menu
Provides function description and available remote commands
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Video
OSD FUNCTION
Function Name
Function
Brightness
Contrast
Color
Adjust the black level of the display.
Adjust the white level of the display.
Adjust the intensity of the colors.
Adjust the color towards either red or green.
Adjust the clarity of the picture.
Hue
Sharpness
Adjust the intensity of the lamp that illuminates the High
Definition LCD TV.
Backlight
Video Reset
Reset the video settings to the factory default.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Display
OSD FUNCTION
Function Name
Function
Change the input name of the current source to one of the
labels in the input label list. If the input label is already used
by another source, the label of the other source will be reset
to the default label.
Input Label
Adjusts the ratio between the width of the picture and the
height of the picture. 16:9 pictures will be displayed at its
original format.
x Standard – conventional format used for viewing 4:3
programs in their normal format.
Aspect Ratio
x Fill – format that horizontally stretches 4:3 pictures to
the edge of the screen (some programs will be
broadcasted with black or gray bars on the top and
bottom or sides of the picture).
PIP
Displays the picture in picture input source menu.
Position
Adjusts the horizontal and vertical position of the picture.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4
OSD FUNCTION
TV
Function Name
Function
Enable / Disable closed captioning. Closed caption is used to
visually communicate audio via text.
Closed Caption
CC Setting
Changes settings for closed captioning such as font, color, and
size.
Choose the type of RF input.
x Air - Normal over-the-air frequency
Tuner Source
x Std (Cable) – Standard frequency used for cable TV
x IRC (Cable) – Incrementally Related Carrier
x HRC (Cable) – Harmonically Related Carrier
Manually input physical channel number(s) and search for
signal reception within that range.
Add Channel
Auto Scan
Automatically scans the tuner’s range of frequencies for all
viewable channels.
Displays the Main Channel List so that you can add / delete a
channel from the current list of viewable channels. See page 24
for more detail.
Delete Channel
Parental Control
EPG
Displays the parental control menu, from which the user can
adjust what content can and cannot be seen on this TV. See
page 25 for more detail.
The electronic programming guide displays the list of available
channels and the corresponding channel information (start time,
end time, program title, program description)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4
PC (VGA Only)
OSD FUNCTION
Function Name
Function
Automatically re-centers the image to the middle of the
screen by synchronizing both vertical and horizontal refresh
rate and resolution.
Auto Adjustment
Manually adjust the Phase control to eliminate horizontal
streaking.
Manual Phase
Auto Phase
Automatically adjust the Phase control to eliminate
horizontal streaking.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Audio
OSD FUNCTION
Function Name
Function
Multi-Channel Television Sound consists of three different
settings. Select one of the following:
x Mono
x Stereo
x SAP
MTS
Mute
Turn audio on/off.
Aux Out
Enable / Disable external audio out.
Switches the HDMI audio input source to one of the following:
x Analog – RCA audio input
HDMI
x Digital – HDMI cable integrated audio input
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Power Management
OSD FUNCTION
Function Name
Function
Enable / Disable the Display Power Management Signaling
which allows the display to go into Standby mode when there
DPMS Mode
is no signal coming in from the selected input.
Enable High Definition LCD TV to automatically turn on when
power is restored.
Sets the High Definition LCD TV to turn off after a specified
time of no remote or panel button presses. Four options
available:
Power On Plug
Inactivity Off
x Off
x 1 hour
x 3 hours
x 6 hours
Sets the High Definition LCD TV to turn off after a specified
amount of time:
x Off
x 30 minutes
x 60 minutes
x 90 minutes
Sleep
NOTE: The High Definition LCD TV will take a few seconds to
come back from sleep mode.
Sets the power boot up mode:
x E. Saver – takes longer to come back from Standby but
requires less power
Power Mode
LED
x Normal – takes faster to come back from Standby but
requires more power
Turns the LED on the TV on and off
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Settings
OSD FUNCTION
Function Name
Function
Switches the language of the OSD to one of the following:
x English
Language
x Spanish
x French
Sets the amount of time of inactivity before the OSD
disappears.
x 10 seconds
x 30 seconds
x 60 seconds
OSD Timeout
Transparency
Time Zone
Adjust the level of transparency of the OSD.
Set the High Definition LCD TV to the local time zone.
Displays the Quick Install Matrix.
Quick Install Matrix
System Info
Displays the system information.
Resets all OSD menu settings (except parental controls) of the
High Definition LCD TV back to the factory defaults.
Factory Reset
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Main Channel List
OSD FUNCTION
Use the OSD to access the Main Channel List.
1
2
1. Channel Number
o Scroll to highlight a channel number from the list of available channels and press
Enter to tune to that channel.
2. Channel Skip / Unskip
o Enable or disable channel in list of channels.
o Channel will not be displayed when scrolling through channels.
o Channel is included in the channel list.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Parental Controls
OSD FUNCTION
The Parental Control feature allows you to block TV programs based on their ratings and
to lock out the keys on the right side of the High Definition LCD TV and can only be
changed by entering the correct 4-digit password. When entering the parental control
menu for the first time, you will be taken to the password submenu to setup a password.
In order for the parental control feature to be activated, you must setup a password.
Rating
Description
Type
MPAA
Rating
Definitions
NR
G
Not available
General audience
PG
Parental guidance suggested
Parents strongly cautioned
Restricted
PG-13
R
NC 17
X
No one 17 and under admitted
Adult audience only
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Parental Controls
OSD FUNCTION
Rating
Type
Description
TV PG
Rating
Rating
Definitions
TV Y
TV Y7
TV G
All children
Directed to older children
General audience
TV PG
TV 14
TV MA
Parental guidance suggested
Parents strongly cautioned
Mature audience only
Content
Definitions
All
FV
D
All Content
Fantasy Violence
Sexually Suggestive Dialog
Adult Language
Sexual Situation
Violence
L
S
V
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Parental Controls (Canadian English)
OSD FUNCTION
Rating
Type
Description
Canadian
English
Rating
C
Definitions
Children
C8
G
Children over 8 years
General
PG
14
Parental Guidance
Over 14 years
Adults
18
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Parental Controls (Canadian French)
OSD FUNCTION
Rating
Type
Description
Canadian
French
Rating
G
Definitions
General
8ans
13ans
16ans
18ans
General but inadvisable for young children
Over 13 years
Over 16 years
Over 18 years
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Parental Controls (Password Edit)
OSD FUNCTION
Function
Name
Description
1. Enter new 4 digit parental control password.
Password
Edit
2. Confirm code by typing password again.
3. Press enter to program new code or press clear to start over.
4. In the case that the password is forgotten, enter “0000” to enter
the parental control menu and reset the password.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Input Menus
OSD FUNCTION
Input Menu
PIP Input Menu
To change the Main Picture source, press the Input button on the remote to display the
Main Picture (MP) input menu. When the input menu is open, press the Input button again
to switch to the next input or use the up/down arrows to scroll through the inputs and the
press enter to switch to the highlighted input. The input menu will timeout after 5 seconds
and switch to the input that is currently highlighted.
To change the PIP source, press the PIP button on the remote to display the PIP input
menu. Use the up/down arrows to scroll through the inputs and the press enter to switch to
the highlighted input. The input menu will timeout after 5 seconds and switch to the input
that is currently highlighted.
INPUT/ PIP SOURCE CHART
PIP
TV
AV
S Video
ATSC
YPbPr1
ATSC
YPbPr2
ATSC
VGA
DVI
HDMI
Main
TV
ATSC
NTSC
O
NTSC
O
AV
ATSC
S Video
YPbPr1
YPbPr2
ATSC
ATSC
ATSC
O
O
O
O
VGA
DVI
ATSC
NTSC
NTSC
HDMI
O
O
O
O
HDMI
O
O
O – PIP and Swap Operates
30
Download from Www.Somanuals.com. All Manuals Search And Download.
5
27 Inch High Definition LCD TV Specifications
APPENDIX
Model Name
Panel
LTV-27w6 HD
27" TFT (Thin Film Transistor), Active Matrix WXGA LCD, 1366 x 768
vertical stripe
Type
Color
Anti-glare coating
Viewing Angles
Input Signal
176° (H) / 176° (V)
Video/Audio
RGB Analog * 1 (75 ohms, 0.7 Vp-p)/Mini-Stereo *1
- H/V separated (TTL) for PC
HDMI-HDCP * 1 / RCA (L/R) * 1
DVI-D * 1 (HDCP support) / RCA (L/R) * 1
- fh: 30-80 kHz, fv: 50-75 Hz NTSC
TV system NTSC / HDTV * 1
Component Video * 2 / RCA (L/R) Stereo * 2
Composite * 1 / S–Video * 1 / RCA (L/R) stereo * 1
RCA (L/R)
Output Signal
HDTV Compatibility
PC Compatible
480i, 480P, 720P, 1080i
Recommended 1360 x 768 @ 60Hz
Supported
1024 x 768 @ 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
1024 x 768 @ 60Hz
1280 x 720 @ 60, 75 Hz
Speaker Output
Power
10W (x2 Channels)
Voltage
100-240 VAC, 47/63 Hz, 2.0A, universal.
0 to + 35° C (Hum < 90%)
-20 to +60o C (Hum < 35%)
20 to 90% non-condensing
10 to 90% non-condensing.
Temperature
Operating
Storage
Operating
Storage
Humidity (Relative)
Altitude
Operating
0 to 3,000 m
Storage
0 to 12,000m
Dimensions
Weight
Physical
Net / Gross
701 mm (W) x 546 mm (H) x 205 mm (D)
11.5 kg / 14.1 kg
Regulations
Power saving
Modes
UL/C-UL, FCC-B
On
<150W Typical (Blue LED)
<3W (Amber LED)
Active Off
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may result in
permanent damage to the High Definition LCD TV.
Note: Product Specifications are subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
5
32 Inch High Definition LCD TV Specifications
APPENDIX
Model Name
Panel
LTV-32w3 HD
32" TFT (Thin Film Transistor), Active Matrix WXGA LCD, 1366*768
vertical stripe
Type
Color
Anti-glare coating
Viewing Angles
Input Signal
176° (H) / 176° (V)
Video/Audio
RGB Analog * 1 (75 ohms, 0.7 Vp-p)/Mini-Stereo *1
- H/V separated (TTL) for PC
HDMI-HDCP * 1 / RCA (L/R) * 1
DVI-D * 1 (HDCP support) / RCA (L/R) * 1
- fh: 30-80 kHz, fv: 50-75 Hz NTSC
TV system NTSC / HDTV * 1
Component Video * 2 / RCA (L/R) Stereo * 2
Composite * 1 / S–Video * 1 / RCA (L/R) stereo * 1
RCA (L/R)
Output Signal
HDTV Compatibility
PC Compatible
480i, 480P, 720P, 1080i
Recommended 1360 x 768 @ 60Hz
Supported
1024 x 768 @ 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
1024 x 768 @ 60Hz
1280 x 720 @ 60, 75 Hz
Speaker Output
10W (x2 Channels)
Power
Voltage
100~264 VAC, 47/63Hz, 2.5A, universal.
0 to + 35° C (Hum < 90%)
-20 to +60o C (Hum < 35%)
20 to 90% non-condensing
10 to 90% non-condensing.
0 to 3,000 m
Temperature
Operating
Storage
Operating
Storage
Operating
Storage
Physical
Humidity (Relative)
Altitude
0 to 12,000m
Dimensions
Weight
820 mm (W) x 614 mm (H) x 205 mm (D)
15.5 kg / 18.9 kg
Net / Gross
Regulations
Power saving
Modes
UL/C-UL, FCC-B
On
<150W Typical (Blue LED)
<3W (Amber LED)
Active Off
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may result in
permanent damage to the High Definition LCD TV.
Note: Product Specifications are subject to change without notice.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Troubleshooting
APPENDIX
No Power
x Make sure power cord is securely connected to the AC In jack on the back of the
High Definition LCD TV.
x Make sure AC power cord is securely connected to the AC socket.
x Plug another electrical device (such as a radio) to the power outlet to verify that the
outlet is supplying the proper voltage.
x When set to E. Saver, the TV will take longer to turn on. Change the Power menu
setting to Normal to improve power on time.
Power is suddenly turned off
x Check if Sleep Timer is set. If so, turn it off.
x Check if Inactivity Off is set. If so, turn it off.
Remote Control Does Not Work
x Press only one button at a time.
x Make sure batteries are inserted correctly.
x Replace batteries with new ones if necessary.
Remote Control Code Not Found in a “Universal” Remote
x Purchase a separate “learning” remote control.
Image Quality Issues
x For the best TV image quality, “Standard Definition” TV content should be viewed in
4:3 format.
No Picture
x Check the video connection.
x Make sure the video cable connected to the High Definition LCD TV is tightly
secured to the video output port on the back of the computer. If the other end of
the video cable is not attached permanently to the High Definition LCD TV, secure it
tightly.
x Adjust brightness and contrast.
x If you are using a Macintosh computer older than G3, you need a Macintosh
adapter.
x Make sure that the input source you are connected to corresponds to the source on
the High Definition LCD TV.
x Verify that the antenna is properly connected.
No Picture when I connect VGA cable or “No Input Signal”
x Check VGA cable connection.
x Lower the video resolution on the computer and try plugging in the cable again.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Troubleshooting
APPENDIX
Picture is cut off/with sidebar screen.
x Use Auto Adjust.
x Make sure the aspect ratio is set correctly.
Blocky images appear in TV mode.
x Check your antenna connection. If necessary, rotate the antenna and wait up to 10
seconds for signal.
x Reduce signal splitters and excessively long cables.
x Replace poor antenna cables and/or connectors to improve signal quality.
Wrong or Abnormal Colors
x If any colors (red, green, or blue) are missing, check the video cable to make sure it
is connected securely. Loose or broken pins in the cable connector could cause an
improper connection.
x Connect the High Definition LCD TV to another computer.
Snow Appears on Screen
x Check your antenna connection. If necessary, rotate the antenna and wait up to 10
seconds for signal.
x Check the TV / CATV selection.
x Make sure the external device is HDCP compliant.
AUDIO Interconnection Issues
x Remember that S-Video and Composite AV1 share the same audio source.
No Sound
x Check the audio connection.
x Press MUTE on the remote control, so that MUTE disappears from the screen.
x Check the audio settings. The High Definition LCD TV audio may be set to SAP or
minimum.
x Press the Volume + (Up) key on the remote control.
Parental Control Password is “LOST”
x In the unlikely occurrence, select “PASSWORD EDIT” and enter “0000” to reset the
password.
How Can I Find More Help?
x Contact Westinghouse Customer Service at (866) 287-5555 or write us at
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Cleaning the High Definition LCD TV
APPENDIX
ʳ
x
x
MAKE SURE THE HIGH DEFINITION LCD TV IS TURNED OFF
NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner
onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If still not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-
abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on
the High Definition LCD TV screen or case. Some chemical cleaners have been reported to
damage the screen and or High Definition LCD TV case. Westinghouse Digital will not be liable for
damage resulting from use of any ammonia or alcohol-based cleaners.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Westinghouse Digital Electronics
Santa Fe Springs, CA
SE-UM-2703-0501
Download from Www.Somanuals.com. All Manuals Search And Download.
Westinghouse Digital Electronics
Comienzo Aquí
Démarre Entière
Start Here
LTV-27w6 HD
LTV-32w3 HD
VGA/Antenna
Inputs
YPbPr/Video/
S-Video/HDMI/
DVI Inputs
Keypad: Power
& OSD Controls
DID YOU KNOW THAT
YOUR LCD TV ALSO HAS:
• Easy side access to connectors through innovative
SpineDesign®
SAVIEZ-VOUS QUE
¿SABÍA USTED QUE SU TELEVISOR CON
PANTALLA DE CRISTAL LÍQUIDO TAMBIÉN TIENE:
• Fácil acceso lateral a los conectores a través del innovador
diseño espinal
VOTRE TV LCD EST AUSSI MUNIE:
• Conception innovante pour faciliter l’accès latéral aux connecteurs
• Syntoniseur HDTV/NTSC entièrement intégré
• Fully integrated HDTV/NTSC tuner
• Sintonizador HDTV/NTSC completamente integrado
CHECK OUT
CONSULTEZ
CONSULTE
• Complete line of TV’s and desktop monitors
• Ligne complète d’écrans TV et d’ordinateurs
•Línea completa de pantallas de televisiones y de computadoras
Quick Install Guide
CONGRATULATIONS on purchasing a Westinghouse high definition LCD TV! This Quick Connect Guide will help you get
started in 3 easy steps. For complete installation, usage instructions, and safety precautions please refer to the User’s Manual.
PLUG IN THE TV
SOURCE SETUP
AUTO SCAN/TIME ZONE
SELECTION
Using the arrow buttons on the
Plug in TV to a properly grounded
power outlet. Connect an antenna
or cable to the TV. Insert batteries
into the remote control and turn the
TV on. Press the “Menu” button
on the remote.
GO!
3
1
2
remote, select the “TV” menu and
scroll to “Tuner Source”. Select “Air” if
na. If you’re using a cable service,
select either “Cable”, “IRC” or “HRC”
(depending on your cable service).
Scroll to “Auto Scan” and press “Enter” on the
remote (Note – This may take several minutes.
Depending on your local area, not all channels
that are found will be available for viewing.
Finally, select the “Settings” menu and scroll to
set your local time zone in order to receive HDTV
programming information.
You are now ready to enjoy
your new Westinghouse high
definition LCD TV.
MAXIMIZE YOUR LCD TV EXPERIENCE You can attach your LCD TV to a variety of electronic devices
including a digital cable or satellite set top box, a game console, a VCR, or a computer. The chart shows our
recommendations for the best quality picture for these commonly used devices.
VGA Audio Input
VGA
YPbPr 2
(Component)
YPbPr 1
(Component)
YPbPr 2
Audio Input
(Component)
YPbPr 1
Audio Input
(Component)
VIDEO INPUTS
PC INPUTS
TV
Tuner
Video S-Video YPbPr HDMI-HDCP
S Video Input
AV Input
VGA
DVI
S Video/AV
Audio Right Input
S Video/AV
Audio Left Input
(RGB)
Digital Cable/
Satellite Receiver
Good
Good
Better
Better
Better
Best
Best
Best
Monitor
Good
Better
DVD Player
Game Console
VCR
DVI-HDCP
Good
Good Better
DVI Audio
L/R Input
Best
•
Remember to adjust the resolution of your
computer to 1360 x 768 for best performance.
Antenna
HDMI Audio L/R
Input (Analog)
Note: The audio input is shared between Video and S-Video
HDMI-HDCP
TYPICAL SETUP
Use the input button on the remote control or keypad
to navigate between the TV, DVI, YPbPr 1, YPbPr 2,
HDMI, Video, S-Video or VGA inputs.
• HD cable or satellite with HDMI
• Game console action using YPbPr
• VCR viewing and editing with Video input
Audio L/R
Ouput
AC In
(Power)
© 2006 Westinghouse Digital Electronics, LLC. All rights reserved. Specifications subject to change without
notice. ¼, Westinghouse and You can be sure... if it's Westinghouse are trademarks of Westinghouse Electric
Corporation and are used under license. MA-PS-0109-0601
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide de Connexion Rapide
FELICITATIONS pour votre achat d’une LCD HDTV! Ce Guide de Connexion Rapide vous aidera à démarrer en
trois étapes simples. Pour une installation complète, des instructions d’utilisation, et des précautions de sûreté
veuillez vous rapporter au Guide de l’Utilisateur.
INSTALLATION DE LA SOURCE
BALAYAGE AUTOMATIQUE
Sur la même option “TV”, sélectionnez
CHOIX DU FUSEAU HORAIRE
COMMENCEZ!
Connectez le câble d’alimentation fourni et
une antenne au moniteur 1080p. Appuyez sur
“Menu” sur la télécommande, si vous utilisez
une antenne de toiture/intérieure, sélectionnez
“Air” sous “Tuner Source” de l’option “TV”. Ou
si vous utilisez le câble, selon votre fournisseur
de télévision par câble, veuillez sélectionner soit
“Câble”, soit “IRC” ou bien “HRC” sous “Tuner
Source” de l’option “TV”.
Pour obtenir l’information de programma-
tion précise de HDTV, veuillez choisir votre
fuseau horaire. Ceci peut être accompli en
naviguant sur l’option “Setting” affichée
sur l’écran et en choisissant votre fuseau
horaire à partir de la liste.
Vous êtes prêt à profiter
de votre nouveau TV LCD
Westinghouse.
“Auto Scan” [Balayage automatique]
1
2 3
et pressez “Enter” sur la télécom-
mande. Remarque: Il est très important
d’exécuter “le balayage automatique”
avant de visionner tous les programmes
HDTV avec une antenne de toiture/
intérieure.
OPTIMISEZ VOTRE EXPERIENCE TV LCD Vous pouvez raccorder votre téléviseur LCD à une
multitude d’appareils électroniques, y compris un boîtier décodeur pour câblodistribution numérique ou
satellite, une console de jeu, un magnétoscope, ou un ordinateur. Le tableau montre nos recommandations
pour une image de qualité supérieure avec ces appareils d’utilisation commune.
Entrée Audio VGA
VGA
YPbPr 2
(Composant)
YPbPr 1
(Composant)
Entrée Audio
YPbPr 2
(Composant)
Entrée Audio
YPbPr 1
(Composant)
ENTRÉES VIDÉO
ENTRÉES PC
HDMI-HDCP
TV
Tuner
Vidéo S-Vidéo YPbPr
Entrée S-Video
Entrée AV
VGA
DVI
Entrée Audio
Droite S-Vidéo/AV
Entrée Audio
Gauche S-Vidéo/AV
(RGB)
Décodeur de
câblodistribution
numérique/satellite
Bien
Bien
Mieux
Mieux
Mieux
Meilleur
Meilleur
Meilleur
Moniteur
Bien
Mieux
DVI-HDCP
Lecteur de DVD
Console de jeu
Magnétoscope
Bien
Bien Mieux Meilleur
Entrée Audio
DVI G/D
Entrée Audio HDMI
G/D (Analogique)
•
Réglez la résolution de l’ordinateur à 1360 x 768
Antenne
Remarque : L’entrée audio est partagée entre Vidéo et S-Vidéo
Utilisez la touche d’entrée sur la télécommande ou le
clavier pour naviguer entre les entrées TV, DVI, YPbPr 1,
YPbPr 2, HDMI, Vidéo, S-Vidéo ou VGA.
MISE EN PLACE TYPIQUE
HDMI-HDCP
• Câble HD ou satellite raccordé à une entrée HDMI
• Console de jeux raccordée à une entrée YPbPr
• Magnétoscope raccordé à l’entrée vidéo pour lecture
et montage vidéo
Sortie
Audio G/D
Entrée CA
(Secteur)
© 2006 Westinghouse Digital Electronics, L.L.C. Tous droits réservés. Spécifications assujetties à des changements
sans préavis. ¼, Westinghouse et Vous pouvez rester tranquilles…si c’est Westinghouse sont des marques de
Westinghouse Electric Corporation et sont utilisées sous licence. MA-PS-0109-0601
Guía De Conexión Rápida
¡FELICITACIONES por comprar un televisor con pantalla de cristal líquido listo para captar transmisiones de televisión de alta
definición! Esta Guía de Conexión Rápida le va a ayudar a conectarlo en tres sencillos pasos. Para ver las instrucciones completas
de instalación y de uso, así como las precauciones de seguridad, por favor consulte el Manual del Usuario.
SELECCIÓN DE ZONA HORARIA
PREPARACIÓN DE LA FUENTE
RASTREO AUTOMÁTICO
¡LISTO!
Conecte el cable de alimentación adjunto y una
antena al monitor 1080p. Apriete “Menú” en el
control remoto, si está utilizando una antena de
tejado/de interior, seleccione “Aire” bajo “Fuente
de Sintonizador” de la pestaña “TV.” O si está
utilizando cable, según su proveedor de cable, por
favor seleccione “Cable,” “IRC” o “HRC” bajo la
“Fuente de Sintonizador” de la pestaña “TV.”
En la misma pestaña “TV,” seleccione
“Auto Scan” (“Rastreo Automático”) y
apriete “Enter” en el control remoto.
Nota: Es muy importante llevar a cabo
un “Rastreo Automático” antes de
ver programas de televisión de alta
definición con una antena de tejado/de
interior.
Para obtener información correcta de
programación de televisión de alta defin-
ición, por favor escoja su zona horaria.
Esto se hace navegando a la pestaña de
visualización de pantalla de “Setting”
(“Configuración”) y seleccionando su
zona horaria en la lista.
3
1
2
Estará listo ahora para
disfrutar de su nuevo
Westinghouse TV LCD.
DISFRUTE AL MÁXIMO SU TELEVISOR DE PANTALLA DE CRISTAL LÍQUIDO Usted podrá conectar su
televisor de pantalla de cristal líquido a una variedad de dispositivos electrónicos, incluyendo un decodificador de cable digital o
de televisión por satélite, una consola de juegos de video, una videograbadora, o una computadora. En la tabla le presentamos
nuestras recomendaciones para obtener la máxima calidad de imagen al usar estos dispositivos de uso general.
Entrada de
Audio VGA
YPbPr 2
(Componente)
YPbPr 1
(Componente)
VGA
YPbPr 2
Entrada de Audio
(Componente)
YPbPr 1
Entrada de Audio
ENTRADAS DE VIDEO
(Componente)
Sintonizador Video Video-S
de TV
YPbPr
DVI-HDCP
ENTRADAS DE PC
Entrada de Video S
Entrada AV
S Video/AV
Entrada derecha
de audio
S Video/AV
VGA
(RGB)
DVI
Cable digital/
Entrada izquierda
de audio
receptor de satélite
Buena
Buena
Mejor
Mejor
Excelente
Excelente
Reproductor de DVD's
DVI-HDCP
Monitor
Bueno
Mejor
Consola de
juegos de video
Buena
Mejor Excelente
Mejor
Excelente
Audio DVI
Entrada I/D
VCR
Buena
•
Fije la resolución de la computadora a 1360 x 768
Antena
HDMI Entrada I/D de
Audio (Análoga)
Nota: La entrada de audio se comparte entre el Video y el S-Video
Use el botón de entrada del control remoto o el teclado para
navegar entre las entradas de TV, DVI, YPbPr 1, YPbPr 2,
HDMI, Video, S-Video o VGA.
HDMI-HDCP
AJUSTE TÍPICO
• Cable o satélite de alta definición con HDMI
• Acción de consola de juegos que usa YPbPr
Salida I/D
de Audio
Entrada de
Corriente
(Electricidad)
• Visualización y editado de VCR con entrada de Video
© 2006 Westinghouse Digital Electronics, LLC. Todos los derechos reservados. Especificaciones sujetas a cambio
sin previo aviso. El símbolo de la ¼, Westinghouse, y Puede Estar Seguro... si es Westinghouse son marcas comer-
ciales propiedad de Westinghouse Electric Corporation y se usan bajo licencia. MA-PS-0109-0601
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|