Model No. WETL14707.0
Serial No.
USER'S MANUAL
Write the serial number in the
space above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. If you have questions,
or if there are missing parts, please
contact us at the numbers or ad-
dresses listed below:
Call: 08457 089 009
Outside UK: 0 (44) 113 3877133
Fax: 0 (44) 113 3877125
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8JG,
UK
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill. ICON assumes no re-
sponsibility for personal inury or property damage sustained by or through the use of this product.
1. Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of
35 or persons with pre-existing health prob-
lems.
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
12. If an extension cord is needed, use only a 3-
conductor, 14-gauge (1mm) cord that is no
longer than 5 ft. (1.5 m).
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
13. Keep the power cord away from heated sur-
faces.
3. Use the treadmill only as described in this
manual.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAIN-
TENANCE AND TROUBLESHOOTING on page
17 if the treadmill is not working properly.)
4. Place the treadmill on a level surface, with at
least 8 ft. (2.5 m) of clearance behind it and
2 ft. (0.5 m) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT on page 10).
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 250 lbs. (113 kg) or less.
18. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
9. Never allow more than one person on the
treadmill at a time.
19. The pulse sensor is not a medical device.
Various factors, including your movement, may
affect the accuracy of heart rate readings. The
pulse sensor is intended only as an exercise
aid in determining heart rate trends in general.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 15.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
11. When connecting the power cord (see page
10), plug the power cord into an earthed cir-
cuit. No other appliance should be on the
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When folding or moving the treadmill, make
sure that the frame is securely held by the
lock pin.
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. Inspect and properly tighten all parts of the
treadmill regularly.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
24. Never drop or insert any object into any
opening on the treadmill.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new WESLO® LYNE 3500
treadmill. The LYNE 3500 treadmill combines ad-
vanced technology with innovative design to make
your workouts at home more effective and enjoyable.
And when you’re not exercising, the LYNE 3500 tread-
mill can be folded up, requiring less than half the floor
space of other treadmills.
using the treadmill. If you have questions after read-
ing this manual, please see the front cover of this man-
ual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
For your benefit, read this manual carefully before
Water Bottle Holder*
Handrail
Console
Key/Clip
Storage Latch
Hood
Walking Belt
Reset/Off
Circuit Breaker
Foot Rail
Wheel
Incline Leg/Pin
Rear Roller
Adjustment Bolts
* No water bottle is included
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
In addition to the included hex key
spanners
, assembly requires a Phillips screwdriver
.
, two
, and wire cutters
Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of
this manual. Some parts may be preassembled. To avoid damaging plastic parts, do not use power tools
for assembly.
1. Have a second person hold the Base (52) in the position
1
shown.
52
Identify the Left Upright (53) (the Right Upright [54] has a
large hole near the lower end).
14
16
54
Hold the Left Upright (53) so the bend is in the posi-
tion shown. Insert two Upright Bolts (2) into the
bracket on the Left Upright. Attach the Left Upright to
the Base (52) with the Upright Bolts, two Frame Washers
(14) and two Upright Nuts (16). Do not tighten the
Upright Nuts yet.
Large
Hole
14
16
2
53
14
Attach the Right Upright (54) to the Base (52) in the
same way.
2
Bend
2. Slide the two Wheel Housings (62) onto the Base (52)
with the head of the Wheel Bolts (35) on the outside as
shown. Attach each Wheel Housing with two Wheel
Housing Bolts (6), two Wheel Housing Washers (11), and
two Wheel Housing Nuts (15).
2
35
62
15
6
11
35
15
52
62
11
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. With the help of a second person, raise the Uprights
(53, 54) so the Base (52) is flat on the floor as shown.
Next, position the front of the treadmill Frame (51) be-
tween the Uprights.
3
Hole
See the inset drawing. Locate the wire inside of the
lower end of the Right Upright (54). Secure the wire to
the Wire Harness (98). Then, pull the upper end of the
wire until the end of the Wire Harness is extending from
the indicated hole in the upper end of the Right Upright.
Remove the wire from the Wire Harness.
53
54
111
Have a second person lift and hold the front end of the
Frame (51). Hold a Frame Spacer (111) between the
Right Upright (54) and the Frame. Attach the Right
Upright and the Frame Spacer to the Frame with a
Frame Pivot Bolt (1), a Frame Washer (14), and a Frame
Star Washer (9).
98
Large
Hole
14
1
9
Repeat this step on the left side of the treadmill.
52
Wire
51
98
54
4. Turn the Console Assembly (91) facedown. Be careful
4
not to scratch the face of the Console Assembly.
5
Identify the Right Handrail (55), which has a large hole
in one side.
12
4
Attach the Right Handrail (55) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12).
Large Hole
55
91
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the Left Handrail (56) on the Console Assembly
(91). Attach the end of the ground wire from the Console
Assembly to the indicated small hole in the Left Handrail
with the Silver Ground Screw (8).
5
5
12
56
4
Attach the Left Handrail (56) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12). Be careful not to
pinch the ground wire.
Ground Wire
8
Small
Hole
91
6. Hold the Console Assembly (91) near the Right Upright
6
(54). Touch the Right Handrail to discharge any static.
Connector
91
Insert the end of the Wire Harness (98) into the hole in
the bottom of the Right Handrail (55) and out of the
large hole in the side. Next, insert the end of the Wire
Harness through the two looped plastic ties.
Press the end of the Wire Harness (98) into the indi-
cated connector on the back of the Console Assembly
(91). The end of the Wire Harness should slide easily
into the connector and snap into place. If it does not,
turn the end of the Wire Harness and try again. IF THE
CONNECTOR IS NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
54
98
Plastic
Ties
55
98
7. Insert the slack in the Wire Harness (98) downward into
the Right Upright (54). Then, tighten the two plastic ties
around the Wire Harness, and cut off the ends of the
plastic ties.
7
54
Plastic
Ties
98
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Set the Console Assembly (91) on the Right Upright (54)
and the Left Upright (not shown). Next, start four
Handrail Bolts (3) with four Handrail Washers (13) and
four Handrail Star Washers (10) (only two of each are
shown) into the Right Upright and the Left Upright.
Then, tighten all four Handrail Bolts.
8
Slot
91
54
7
Insert the slack in the Wire Harness (98) down into the
Right Upright (54).
Attach the Console Back (93) to the Console Assembly
(91) with four Console Back Screws (7). Make sure that
the Wire Harness (98) is in the indicated slot in the
Console Back and that no wires are pinched.
93
7
98
10
13
3
9. Carefully lower the Right and Left Handrails (55, 56) to
the floor. Center the Frame (51) between the Handrails,
and tighten the four Upright Bolts (2). Then, raise the
Handrails back to the vertical position.
9
2
51
See the inset drawing. Attach the Latch Assembly (108)
to the Left Upright (53) with two Latch Screws (7). Make
sure that the Latch Assembly is oriented as shown.
55, 56
See HOW TO CHANGE THE INCLINE OF THE TREAD-
MILL on page 14. Adjust the incline of the treadmill as
desired.
53
108
7
10.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 18). To protect the floor or carpet, place a mat under the treadmill.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-
cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-
rate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric cur-
1
Socket on treadmill
rent to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the power cord into the metal clips
2
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter. Important: Make
sure that the adapter cover is secure and the screw has been
tightened before using the power cord.
Adapter
Cover
Screw
Pins
Adapter
Metal
Clips
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
3
Outlet
DANGER:
Improper connection of the equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Key
Clip
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers a selection of features
designed to make your workouts more effective.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
While the manual mode of the console is selected, the
speed of the treadmill can be changed with the touch
of a button. As you exercise, the displays will provide
continuous exercise feedback. You can even measure
your heart rate using the handgrip pulse sensor.
Plug in the power cord (see
page 10). Next, locate the
reset/off circuit breaker on
Reset
Position
The console also offers four speed programs. Each
program automatically controls the speed of the tread-
mill as it guides you through an effective workout.
the treadmill frame near the
power cord. Switch the cir-
cuit breaker to the reset po-
sition.
Note: If there is a sheet of clear plastic on the con-
sole, remove the plastic. To prevent damage to the
walking platform, always wear clean athletic shoes
while using the treadmill. During the first few min-
utes that the treadmill is used, inspect the align-
ment of the walking belt, and center the walking
belt if necessary (see page 18).
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above) and
slide the clip onto the waistband of your clothes. Then,
insert the key into the console. After a moment, the
displays will light. IMPORTANT: In an emergency sit-
uation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
The lower left display—
As you exercise, the
lower left display can
show the elapsed time
and the distance that you
have walked or run in
miles or kilometers.
See HOW TO TURN ON THE POWER on page
11.
2. Select the manual mode.
The lower right
When the key is in-
display—The lower right
serted, the manual
display can show the
mode will be selected. If
you have selected a
speed of the walking belt
in miles or kilometers per
speed program, reselect
the manual mode by
pressing the Program Select button repeatedly
until only zeros appear in the displays.
hour and the approximate
number of calories that you have burned. The dis-
play also shows your heart rate when you use the
handgrip pulse sensor (see step 5 on page 13).
3. Press the Start button or the Speed increase
button to start the walking belt.
The priority display—
The upper display is the
priority display. The prior-
When either button is pressed, the walking belt will
begin to move at 2 km/h. Hold the handrails and
begin walking. As you exercise, change the speed
of the walking belt as desired by pressing the
Speed buttons. Each time a button is pressed, the
speed setting will change by 0.1 km/h; if a button is
held down, the speed setting will change in incre-
ments of 0.5 km/h. Note: After the buttons are
pressed, it may take a moment for the walking belt to
reach the selected speed setting.
ity display can show the
elapsed time, the dis-
tance that you have
walked or run, the speed of the walking belt, or the
approximate number of calories you have burned.
Press the Priority Display button repeatedly until the
priority display shows the information that you are
most interested in viewing. Note: While information
is shown in the priority display, the same informa-
tion will not be shown in the lower left or lower right
display.
To stop the walking belt, press the Stop button.
The time will begin to flash in one of the displays.
To restart the walking belt, press the Start button or
the Speed increase button.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
Note: The console can
4. Follow your progress with the track and the
three displays.
display speed and dis-
tance in either kilometers
or miles. To see which
The track—The track
unit of measurement is
represents a distance of
selected, hold down the
400 meters (1/4 mile).
As you walk or run on
the treadmill, the indica-
tors around the track will
appear in succession until the entire track appears.
The track will then disappear and the indicators will
again begin to appear in succession. The center of
the track will show the number of laps that you
have completed.
Stop button, insert the key into the console, and
then release the Stop button. An “M” for metric kilo-
meters or an “E” for English miles will appear in the
priority display. Press the Speed increase button to
change the unit of measurement. When the desired
unit of measurement is selected, remove the key
and then reinsert it.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Measure your heart rate if desired.
Each program consists of 30 one-minute seg-
ments. One speed setting is programmed for each
segment. Note: The same speed setting may be
programmed for two or more consecutive seg-
ments. The profiles on the left side of the Program
Select button show how the speed of the walking
belt will change during the programs.
Before using the hand-
grip pulse sensor, re-
move the sheets of clear
plastic from the metal
contacts. In addition,
make sure that your
hands are clean.
Metal
Contacts
3. Press the Start button or the Speed increase
button to start the program.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, the small
heart symbol in the lower right display will flash,
one or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
When either button is pressed, the treadmill will au-
tomatically adjust to the speed setting that is pro-
grammed for the first segment of the program.
Hold the handrails and begin walking.
When the first segment ends, a series of tones will
sound. If a different speed setting is programmed
for the second segment, the speed setting will flash
in one of the displays to alert you, and then the
speed of the walking belt will change. The pro-
gram will continue until all 30 segments are com-
pleted. The walking belt will then slow to a stop.
6. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button. Next,
remove the key from the console and put it in a se-
cure place.
If the speed setting is too high or too low during the
program, you can manually override the setting by
pressing the Speed buttons. However, when the
next segment begins, the speed of the walking
belt will change if a different speed setting is
programmed for the next segment.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical compo-
nents may wear prematurely.
To stop the program, press the Stop button. The
time will begin to flash in one of the displays. To
restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 2 km/h. When the next segment begins,
the speed of the walking belt will change if a differ-
ent speed setting is programmed for the next seg-
ment.
HOW TO USE A SPEED PROGRAM
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2. Select one of the four speed programs.
4. Follow your progress with the track and the
three displays.
To select a speed pro-
gram, press the
See step 4 on page 12.
Program Select button
repeatedly; “P-1,” “P-2,”
“P-3,” or “P-4” will ap-
5. When you are finished exercising, remove the
key from the console.
pear in the priority dis-
play for a few seconds to show which program is
selected. The maximum speed setting of the se-
lected program will also appear in one of the dis-
plays for a few seconds.
See step 6 on this page.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To change the incline, first remove the incline pin from
one of the incline legs. Adjust the incline leg to the de-
sired position, and then fully reinsert the incline pin.
Adjust the other incline leg in the same way. CAUTION:
Before using the treadmill, make sure that both in-
cline legs are at the same height and that both in-
cline pins are fully inserted into the incline legs.
To vary the intensity of your exercise, you can change
the incline of the treadmill. There are three incline lev-
els. Before changing the incline, remove the key
and unplug the power cord. Next, fold the treadmill
to the storage position (see page 15).
After you have adjusted the incline legs, lower the
treadmill (see page 16).
Incline
Pin
Incline
Leg
Incline Pin
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Unplug the power cord. CAUTION: You must be able to
safely lift 45 lbs. (20 kg) to raise, lower, or move the
treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the
possibility of injury, do not lift the frame by the plas-
tic foot rails. Make sure to bend your legs and keep
your back straight. As you raise the frame, make sure
to lift with your legs with your back. Raise the frame
about halfway to the vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
past the latch pin. Then, slowly release the latch knob;
make sure that the latch pin is resting against the
catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° F (30° C).
Latch
Pin
Latch
Knob
Catch
HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
pin is resting against the catch.
1. Hold the handrails and place one foot against one of the
wheels. Do not pull back on the frame.
Handrail
Wheel
2. Tilt the treadmill backward until it rolls freely on the
wheels, and carefully move the treadmill to the desired
location. Never move the treadmill without tipping it
backward. To reduce the risk of injury, use extreme
caution while moving the treadmill. Do not attempt to
move the treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Next, lower the frame until it is past the
latch pin. Then, release the latch knob.
Latch
Pin
Latch
Knob
Catch
2. Hold the frame firmly with both hands, and lower it to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 10). If an exten-
sion cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft.
(1.5 m). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
20
65
POWER CORD. Remove the five indicated Hood
Screws (20) and the two Foot Rail Screws (25). Then,
carefully remove the Hood (65).
20
20
25
Locate the Reed Switch (97) and the Magnet (105) on
the left side of the Pulley (104). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 1/8 in. (3 mm). If necessary,
loosen the Screw (21), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Hood, and
run the treadmill for a few minutes to check for a cor-
rect speed reading.
3 mm
21
104
105
97
Top View
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 5 ft. (1.5 m).
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2-3 in.
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 7
cm) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few min-
utes. Repeat until the walking belt is properly tight-
ened.
Rear Roller
Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
a
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the hex key to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking
belt has shifted to the right, turn the left rear roller
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first re-
b
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clock-
wise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 in. (5 to 7 cm) off the walking plat-
form. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and
carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over the age of 35 or persons with pre-exist-
ing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic ex-
ercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning, maximum fat burning, and aerobic exer-
cise.
Warm-up—Start with 5 to 10 minutes of stretching and
light exercise. A warm-up increases your body temper-
ature, heart rate, and circulation in preparation for ex-
ercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cool-down—Finish with 5 to 10 minutes of stretching.
Stretching increases the flexibility of your muscles and
will help to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, first find your age at
the bottom of the chart (ages are rounded off to the
nearest ten years). The three numbers listed above
your age define your “training zone.” The lowest num-
ber is the heart rate for fat burning, the middle number
is the heart rate for maximum fat burning, and the
highest number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to pro-
vide the following information when contacting us:
• the model number and the serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the part(s) (see the PARTS LIST and the EXPLODED DRAWING in the cen-
ter of this manual)
RECYCLING INFORMATION
This electronic product must not be disposed of in municipal waste. To
preserve the environment, this product must be recycled after its useful
life as required by law.
Please use recycling facilities that are authorized to collect this type of waste in
your area. In doing so, you will help to conserve natural resources and improve
European standards of environmental protection. If you require more information
about safe and correct disposal methods, please contact your local city office or
the establishment where you purchased this product.
Part No. 255693 R0607A
Printed in China © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED
DRAWING/PART LIST for future reference. The number in parentheses below each drawing is the key number
of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity
needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to
be assembled. Extra hardware may be included.
Console
Screw (4)–4
Crossbar
Screw (5)–2
Silver Ground
Screw (8)–1
Latch/Console
Back Screw
(7)–6
Crossbar Star
Washer (12)–2
Wheel Housing
Washer (11)–4
Wheel Housing Bolt (6)–4
Upright Bolt (2)–4
Handrail Star
Washer (10)–4
Upright Nut
(16)–4
Handrail
Washer (13)–4
Wheel Housing
Nut (15)–4
Frame Star
Washer (9)–2
Handrail Bolt (3)–4
Frame Washer
(14)–6
Frame Pivot Bolt (1)–2
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WETL14707.0
R0607A
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
2
4
4
4
2
4
6
Frame Pivot Bolt
Upright Bolt
Handrail Bolt
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
4
2
2
5
5
4
3
2
1
1
1
1
1
1
1
1
1
1
Incline Leg Washer
Motor Tension Nut
Frame Pivot Nut
Nut
Hood Clip
Handrail Nut
Small Nut
Isolator Fastener
Frame
Base
Left Upright
Right Upright
Right Handrail
Left Handrail
Electronics Bracket
Dust Guard
Motor Bracket
Left Rear
Roller Bracket
Right Rear
Roller Bracket
Wheel Housing
Base Pad
Latch Catch
Hood
Belly Pan
Left Foot Rail
Right Foot Rail
Incline Leg
86
1
Reset/Off
Circuit Breaker
Controller
Transformer
Filter
Power Cord
Console
Console Crossbar
Console Back
Receptical
4" Ground Wire
6" Ground Wire
Reed Switch
Wire Harness
Outlet Plate
Walking Platform
Walking Belt
Tie Holder Screw
Belt Guide
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
–
–
–
–
–
–
–
–
–
–
Console Screw
Crossbar Screw
Wheel Housing Bolt
Latch Screw/
Console Back Screw
Silver Ground Screw
Frame Star Washer
Handrail Star Washer
Wheel Housing
Washer
Crossbar Star Washer
Handrail Washer
Frame Washer
Wheel Housing Nut
Upright Nut
6 mm Hex Key
4 mm Hex Key
Roller Bracket Screw
Hood Screw
8
9
10
11
1
2
4
4
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
2
4
6
4
6
1
1
2
5
13
1
1
2
10
6
2
4
2
2
1
2
2
2
2
2
61
1
Front Roller/Pulley
Magnet
Motor Belt
Rear Roller
Latch Assembly
Key/Clip
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
2
6
1
1
1
1
1
2
2
4
1
2
2
2
4
2
Screw
Front Roller Adj. Bolt
Ground Screw
Outlet Plate Bolt
Foot Rail Screw
Base Pad Screw
Walking Platform Bolt
Belt Guide Screw
Rear Roller Adj. Bolt
Motor Bolt
Motor Pivot Bolt
Incline Leg Bolt
Isolator Screw
Motor Tension Bolt
Wheel Bolt
Incline Pin
Frame Spacer
Power Adapter
Warning Decal
6" Red Wire, M/F
4" Black Wire, M/F
4" Blue Wire, M/F
8" Blue Wire, 2F
10" Blue Wire, 2F
6" White Wire, 2F
10" White Wire, 2F
8" Green/Yellow Wire
4" Black Wire, 2F
User’s Manual
Wheel
Wheel Spacer
Motor Isolator
Motor Bushing
Frame Endcap
Upright Endcap
Handrail Endcap
Platform
*
*
*
*
*
*
*
*
Rear Roller
Star Washer
Cushion, Front
Platform
78
2
*
37
1
Front Roller
Star Washer
Cushion, Center
Drive Motor
Wire Tie
8" Tie
Tie Holder
Reed Switch Clip
Belly Pan Grommet
Grommet
79
80
81
82
83
84
85
1
4
4
1
1
1
1
*These parts are not illustrated.
Specifications are subject to
change without notice.
38
39
40
41
42
2
2
1
11
2
Motor Star Washer
Outlet Plate Washer
Ground Star Washer
Tek Screw
Electronics Star
Washer
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WETL14707.0
R0607A
Download from Www.Somanuals.com. All Manuals Search And Download.
|