Model No. WEBE0878.0
Serial No.
Write the serial number in the
USERʼS MANUAL
space above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete cus-
tomer satisfaction. If you have
questions, or if parts are missing,
DO NOT CONTACT THE STORE;
please contact Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-877-992-5999
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your inversion system before using your inversion
system. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of the inversion system.
1. Before beginning any exercise program, con- 12. Keep hands and feet away from moving
sult your physician. This is especially impor-
tant for persons over the age of 35 or per-
sons with pre-existing health problems.
parts.
13. Always make sure that the ankle lock is
secured snugly against your ankles and that
the short knob is fully tightened before you
use the inversion system.
2. Use the inversion system only as described
in this manual.
3. It is the responsibility of the owner to ensure
that all users of the inversion system are
adequately informed of all precautions.
14. Perform all activities on the inversion system
in a slow, controlled manner. Aggressive
exercise can cause the inversion system to
tip over.
4. The inversion system is intended for home
use only. Do not use the inversion system in
any commercial, rental, or institutional set-
ting.
15. Always exercise with a partner. Your partner
should be ready to return the backrest to the
upright position if you cannot complete the
rotation.
5. Keep the inversion system indoors, away
from moisture and dust. Do not put the inver-
sion system in a garage or covered patio or
near water.
16. If you feel pain or dizziness while exercising,
stop immediately and cool down.
17. Following is a list of factors and conditions
that may make inverting inadvisable (this list
is not exhaustive; it is intended only for refer-
ence). If one or more factors or conditions
apply to you, consult your physician before
using the inversion system.
6. Use the inversion system only on a level sur-
face. Cover the floor beneath the inversion
system to protect the floor.
7. Make sure that all parts are properly tight-
ened each time the inversion system is used.
Replace any worn parts immediately.
• Pregnancy
• Hiatal hernia or ventral hernia
• Glaucoma, retinal detachment, or conjunc-
tivitis
8. Keep children under age 12 and pets away
from the inversion system at all times.
• High blood pressure, hypertension, or
recent stroke or transient ischemic attack
• Heart or circulatory disorders for which
you are being treated
9. The inversion system is designed to support
a maximum user weight of 300 lbs. (136 kg).
Do not use weights with the inversion sys-
tem.
• Middle ear infection and extreme obesity
• Spinal injury, cerebral sclerosis, or acutely
swollen joints
• Bone weakness (osteoporosis), recent
unhealed fractures, medullary pins, or sur-
gically implanted orthopedic supports
• The use of anticoagulants, including high
doses of aspirin
10. Always wear athletic shoes with laces to help
secure your feet in the inversion system, and
for foot protection while exercising.
11. The inversion system should be used only by
persons 6 ft. 6 in. (198 cm) tall or less.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER CLUB™ model number and serial number before contacting us.
INVERSION SYSTEM. The inversion system will
The model number and the location of the serial num-
increase your intervertebral dimension, decrease pres- ber decal are shown on the front cover of this manual.
sure on intervertebral discs, stretch and relax your
muscles, and temporarily relieve back pain associated
with the listed conditions.
To avoid a registration fee for any service needed
under warranty, you must register the inversion
For your benefit, read this manual carefully before
using the inversion system. If you have questions
Before reading further, please review the drawing
after reading this manual, please see the front cover of below and familiarize yourself with the parts that are
this manual. To help us assist you, note the product
labeled.
ASSEMBLED DIMENSIONS:
Height: 4 ft. 9 in. (145 cm)
Width: 2 ft. 4 in. (71 cm)
Depth: 4 ft. 1 in. (125 cm)
Backrest
Pivot Bar
Handle
Pin (under the Backrest)
Short Adjustment Knob
Adjustment Frame
Long Adjustment Knob
Ankle Lock
Link Bar
Foot Frame
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST near the end of this manual. Note: Some small parts may
have been preattached. If a part is not in the hardware kit, check to see if it has been preattached.
M6 Locknut (55)
M6 Flat
M8 Locknut (54)
M8 Flat
M8 Curved Washer (53)
M6 x 37mm Bolt (65)
Washer (51)
Washer (52)
M4 x 15mm
Screw (61)
M8 x 20mm
M6 x 18mm
M8 x 15mm
Button Bolt (64)
Button Screw (50)
Button Screw (47)
M8 x 45mm Button Bolt (43)
M8 x 50mm Button Bolt (58)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• For help identifying small parts, see the PART
IDENTIFICATION CHART on page 5.
Make Assembly Easier
This manual is designed to ensure that the
inversion system can be assembled successfully
by almost anyone. Most people find that if they
set aside plenty of time, assembly goes smoothly.
• As you assemble the inversion system, make sure
that all parts are oriented as shown in the draw-
ings.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires the following tools:
• To hire an authorized service technician to
assemble the inversion system in your home, call
1-800-445-2480.
the included hex key(s)
two adjustable wrenches
one rubber mallet
• Assembly requires two persons.
one standard screwdriver
one Phillips screwdriver
• Because of its weight and size, the inversion sys-
tem should be assembled in the location where it
will be used. Make sure that there is enough
clearance to walk around the inversion system as
you assemble it.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
1.
1
Before beginning assembly, make sure
that you understand the information in
the box above.
3
12
Open the Front and Rear Legs (1, 2, 3), and
push down on the Link Bars (10, 11, 12) so
that they are straight across as shown.
10
3
1
12
11
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the Front Leg Frame (5) to the Front
Legs (1, 2) with four M8 x 45mm Button Bolts
(43), four M8 Curved Washers (53), and four
M8 Locknuts (54). Do not tighten the
Locknuts yet.
2
53
43
54
2
5
54
53
54
53
43
1
54
53
3. Attach the two Bases (4) to the Front and Rear
Legs (1, 2, 3) as shown with four M8 x 45mm
Button Bolts (43).
3
3
3
1
43
4
2
4
43
43
43
4. Attach the Backrest Frame (6) to the Center
Frame (13) as shown with an M8 x 50mm
Button Bolt (58), two M8 x 45mm Button Bolts
(43), two M8 Flat Washers (52), and three M8
Locknuts (54).
4
43
6
54
13
58
52
54
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Attach the Foot Frame (8) to the Adjustment
Frame (7) with three M8 x 15mm Buttons
Screws (47).
5
7
47
8
47
9
6. Slide the two Large Foam Pads (32) onto the
Ankle Lock (9).
6
Next, pull the Long Adjustment Knob (20),
insert the Ankle Lock (9) into the Adjustment
Frame (7), and then release the Long
32
Hole
41
Adjustment Knob. Make sure that the Long
Adjustment Knob is engaged in the indicat-
ed adjustment hole in the Ankle Lock.
20
55
Insert an M6 x 37mm Bolt (65) into the
Adjustment Frame (7) and into the loop on
the end of the Spring (41). Tighten an M6
Locknut (55) onto the Bolt.
7
32
65
7. Insert the Pad Tube (17) into the welded tube
on the Adjustment Frame (7). Next, tighten an
M4 x 15mm Screw (61) into each side of the
Pad Tube. Then, slide two Small Foam Pads
(33) onto the Pad Tube.
7
33
7
17
61
33
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Orient the two Pivot Bars (14) so that the
Pulleys (22) face away from the Center Frame
(13). Then, insert the Pivot Bars into the brack-
ets on the ends of the Center Frame, and
engage the pins on the brackets into the cen-
ter adjustment holes in the Pivot Bars.
8
22
14
22
14
Insert the two Pulleys (22) down into the slots
in the Saddle Plates (18).
Pin
See step 2. Tighten the four M8 Locknuts (54).
13
Pin
18
18
9. Pull the Short Adjustment Knob (19), and
insert the end of the Adjustment Frame (7) a
few inches into the Backrest Frame (6).
9
6
See the inset drawing. Press the round tab
on the Backrest Frame Bushing (25), and
press the Backrest Frame Bushing into the
Backrest Frame (6). Make sure that the
round tab is in the indicated hole in the
Backrest Frame.
63
24
19
7
Next, insert the Adjustment Frame (7) farther
into the Backrest Frame (6), and engage the
Short Adjustment Knob (19) into one of the
adjustment holes in the Adjustment Frame.
Then, insert the Pin (24) into the Backrest
Frame (6) and the Adjustment Frame (7), and
attach the Pin Clip (63) to the Pin.
Hole
Tab
Use the inversion system with the Adjustment
Frame (7) adjusted to a few different lengths to
determine which length is the best for you.
6
25
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Attach the Backrest (23) to the Backrest Frame
(6) with four M6 x 18mm Button Screws (50)
and four M6 Flat Washers (51).
10
23
6
51
50
51
11. Attach the Right and Left Handles (15, 16) to
the Front and Rear Legs (1, 2, 3) with four M8
Locknuts (54).
11
15
54
16
1
54
3
3
2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Slide the Left Cover (31) onto the left Saddle
Plate (18). Attach the Left Cover with a Small
Knob (42).
12
30
Attach the Right Cover (30) in the same
way.
31
18
42
13. See the inset drawings. Open the Quick
13
Link (29) by turning the quick link nut.
6
Then, attach one end of the included Chain
(28) to the indicated bracket on the Front Leg
Frame (5) with the Quick Link (29). Close the
Quick Link by turning the quick link nut.
27
Attach the other end of the Chain (28) to the
hook on the Backrest Frame (6) with the Clip
(27). Make sure that the Quick Link (29) is
attached to the Front Leg Frame and that
the Clip is attached to the Backrest Frame.
5
Bracket
28
29
Make sure that all parts are properly tight-
ened before you use the inversion system.
Closed
Open
WARNING:
7
HOW TO LOCK THE INVERSION SYSTEM
FOR STORE DISPLAY OR TO PREVENT
UNSUPERVISED USE
5
62
54
When the inversion system is displayed in
a store, or when it is not in use, it should
be locked to prevent unsupervised use.
Wrap the Lock Cable (62) around the Front
Leg Frame (5) and the Adjustment Frame
(7) as shown. Then, connect the ends of
the Lock Cable with an M8 x 20mm Button
Bolt (64) and an M8 Locknut (54).
64
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT
This section explains how to adjust the inversion system. See DEVELOPING A PROGRAM on page 16 for
important information about how to get the most benefit from your exercise program.
Make sure all parts are properly tightened each time the inversion system is used. Replace any worn parts immedi-
ately. The table can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not use solvents.
SELECTING A PIVOT BAR POSITION
See the inset drawing. Each Pivot Bar (14) has
three adjustment holes. The correct adjustment hole
Note: 1 lb. = 2.2 kg
to use will depend on your body weight and the
desired level of responsiveness. See the chart at the
right to determine which adjustment hole to use.
To adjust the Pivot Bars (14), first remove the two
Small Knobs (42) and the two Covers (30, 31). Next,
lift the two Pulleys (22) out of the Saddle Plates (18).
Move the Pivot Bars upward or downward so that the
pins on the Backrest Frame (6) are engaged in the
desired adjustment holes. Then, insert the Pulleys into
the Saddle Plates, and attach the Covers.
30
14
22
42
Try the inversion system with the Pivot Bars (14)
adjusted to each position to determine which one is
best for you.
31
18
22
6
14
WARNING:
Always engage the
pins on the Backrest Frame (6) in the same
adjustment holes in the Pivot Bars (14).
42
Pin
Hole A
Hole B
Hole C
14
ADJUSTING THE LENGTH OF THE CHAIN
The chain can be used to stop the inversion system
from becoming inverted more than desired. To adjust
the chain, remove it from the Clip (27) on the
23
6
Backrest Frame (6). Rotate the Backrest (23) to the
most inverted position to which you want it to move.
Then, have a second person tighten the chain and
reattach it to the Clip on the Backrest Frame.
27
For the first week or two of use, adjust the chain to
stop the Backrest (23) from rotating more than 15–20
degrees. Lengthen the chain to allow the Backrest to
rotate a few more degrees as you become accus-
tomed to using the inversion system.
Chain
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE ADJUSTMENT FRAME
The length of the Adjustment Frame (7) can be
adjusted to correspond to your height. First, remove
the Pin (24) from the Backrest Frame (6) and the
Adjustment Frame. Pull the Short Adjustment Knob
(19) as far as possible. Slide the Adjustment Frame
into or out of the Backrest Frame so that the first or
second measurement greater than your height is cov-
ered by the Backrest Frame. Next, engage the Short
Adjustment Knob into one of the adjustment holes in
the Adjustment Frame. Then, insert the Pin into the
Backrest Frame and the Adjustment Frame, and
attach the Pin Clip (63) to the Pin.
63
6
Height
Measurements
7
19
24
Adjustment
Hole
Use the inversion system with the Adjustment Frame
(7) adjusted to a few different lengths to determine
which length is best for you.
WARNING:
The inversion system
is designed to be used by persons 6 ft. 6 in.
(198 cm) tall or less.
ADJUSTING THE ANKLE LOCK
20
To secure your ankles in the inversion system, first
pull the Long Adjustment Knob (20) as far as possi-
ble. See the inset drawing. Next, pull the Ankle Lock
(9) away from the Adjustment Frame (7). Stand on
the Foot Frame (8) with the backs of your legs
against the Small Foam Pads (33) and your toes
under the Ankle Lock. Then, push the Ankle Lock
against your ankles and engage the Long Adjustment
Knob into one of the adjustment holes in the Ankle
Lock. Make sure that the Long Adjustment Knob is
engaged into one of the adjustment holes in the
Ankle Lock.
33
9
20
7
WARNING:
Make sure that the
Ankle Lock (9) is secured snugly against your
ankles before you use the inversion system.
Always wear athletic shoes with laces to help
secure your feet in the inversion system.
8
33
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCKING THE INVERSION SYSTEM
When the inversion system is not in use, it should be
locked to prevent unsupervised use. Wrap the Lock
Cable (62) around the Front Leg Frame (5) and the
Adjustment Frame (7) as shown. Then, connect the
ends of the Lock Cable with an M8 x 20mm Button
Bolt (64) and an M8 Locknut (54).
7
5
62
54
64
STORING THE INVERSION SYSTEM
To store the inversion system, first adjust the
Adjustment Frame (7) to the shortest length (see
ADJUSTING THE ADJUSTMENT FRAME on page
13). Next, adjust the Ankle Lock (9) to the position
closest to the Adjustment Frame (see ADJUSTING
THE ANKLE LOCK on page 13). Then, lift on the Link
Bars (10, 11, 12) and fold the Front and Rear Legs (1,
2, 3) together.
12
10
3
1
7
3
12
9
WARNING:
Always make sure that
11
the Link Bars (10, 11, 12) are straight across
before you use the inversion system.
2
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTATING ON THE INVERSION SYSTEM
This section explains how to rotate back on the inversion system, and then return to the starting position. Before
using the inversion system, see the ADJUSTMENT section starting on page 12 to correctly set up the
inversion system.
ROTATING BACK ON THE INVERSION SYSTEM
ROTATING UP ON THE INVERSION SYSTEM
To rotate back on the inversion system, slowly lift your
arms over your head until you reach the desired posi-
tion. The speed at which you lift your arms will deter-
To return to the starting position, move your hands
toward your waist until you rotate to a horizontal posi-
tion. Rest in a horizontal position for 30 to 60 seconds
mine how quickly the inversion system will rotate. Rest before rotating to the starting position. This will allow
your arms in a comfortable position that does not
cause the inversion system to rotate. Note: The inver-
sion system will rotate only to the degree setting
allowed by the chain.
your body to readjust. Return to the starting position
slowly. Dizziness after using the inversion system is an
indication that you have returned to the starting position
too quickly.
To rotate up from the fully inverted position, pull your-
self up using the handles.
Do not sit up to return to the starting position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DEVELOPING A PROGRAM
This section contains information and suggestions about using the inversion system. Make sure that all parts are
properly tightened each time you use the inversion system. Replace any worn parts immediately. See the
ADJUSTMENT section starting on page 12 to identify parts referred to in this section.
BENEFITING FROM USING THE INVERSION
SYSTEM
INTERMEDIATE PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion system as
described under the BEGINNER PROGRAM.
If you feel nauseated while using the inversion system,
return to the starting position. Be aware that it may take
a few weeks of use for your inner ear to become accus-
tom to being inverted.
Increase the angle to which the inversion system can
rotate, as it is comfortable. Adjust the chain to allow
the inversion system to rotate to up to 60 degrees, a
few degrees at a time.
Do not use the inversion system right after you have
eaten.
Moving while using the inversion system may make it a
more comfortable experience, and may help joints and
muscles stretch and relax. Always move in a slow, con-
trolled manner.
Start to do gentle stretching while using the inversion
system.
Gradually increase the amount of time that you use
the inversion system to ten minutes or more, two or
three times a day. Routines can be varied from rotat-
ing back for one or two minutes and then up for 30
seconds, to rotating back and up for equal amounts of
time.
The greater the angle at which the inversion system is
used, the shorter the time that you should rotate back
before rotating up. Increase the amount of inverted time
and the angle of use gradually.
Always pay attention to how your body feels as you use
the inversion system. Increase the level of intensity only
as it is comfortable for you. When you feel like you have
had enough, return to the starting position.
FULL INVERSION PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion system as
described under the INTERMEDIATE PROGRAM and
desire to rotate to greater angles. Note that all the
benefits of inversion can be gained by rotating to 60
BEGINNER PROGRAM
The following are suggestions for persons who are just degrees. Do not attempt to do sit-ups.
starting to use the inversion system.
Increase the angle to which the inversion system can
Adjust the chain to allow the backrest frame to rotate
to 15 degrees or less for the first one or two weeks.
This will allow your body time to adjust to the change
in gravitational pull.
rotate, as it is comfortable.
Adjust the pivot bars so that the pins on the backrest
frame are in the top holes in the pivot bars (see
SELECTING A PIVOT BAR POSITION on page 12). If
you weigh 220 lbs. (100 kg) or more, adjust the pivot
bars so that the pins on the backrest frame are in the
center holes in the pivot bars. Rotate back and up as
Use the inversion system for one or two minutes at a
time, two or three times a day.
Stay inverted only for as long as it is comfortable. This described on page 15.
may be only a few seconds at first.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WEBE0878.0
R1008A
Key No. Qty.
Description
Key No. Qty.
Description
1
1
1
2
2
1
1
1
1
1
1
1
2
1
2
1
1
1
2
1
1
2
2
1
1
1
1
1
1
1
1
1
2
2
Right Front Leg
Left Front Leg
Rear Leg
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
*
4
1
32mm Round Outer Cap
Bumper
2
3
2
25mm Round Inner Cap
30mm x 70mm Inner Cap
Foam Grip
4
Base
2
5
Front Leg Frame
Backrest Frame
Adjustment Frame
Foot Frame
2
6
4
19mm Round Inner Cap
25mm Square Inner Cap
Spring
7
1
8
1
9
Ankle Lock
2
Small Knob
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Right Link Bar
Left Link Bar
Rear Link Bar
Center Frame
Pivot Bar
10
2
M8 x 45mm Button Bolt
M12 x 50mm Bolt
M6 x 40mm Bolt
M6 x 15mm Bolt
M8 x 15mm Button Screw
M8 x 20mm Button Bolt
M8 x 30mm Button Bolt
M6 x 18mm Button Screw
M6 Flat Washer
4
2
3
Right Handle
Left Handle
2
4
Pad Tube
4
Saddle Plate
Short Adjustment Knob
Long Adjustment Knob
Spacer
10
4
M8 Flat Washer
4
M8 Curved Washer
M8 Locknut
14
8
Pulley
M6 Locknut
Backrest
2
M12 Nut
Pin
4
M8 Nut
Backrest Frame Bushing
34mm Square Inner Cap
Clip
1
M8 x 50mm Button Bolt
M6 x 33mm Bolt
45mm Square Inner Cap
M4 x 15mm Screw
Lock Cable
1
1
Chain
4
Quick Link
1
Right Cover
Left Cover
1
Pin Clip
1
M8 x 20mm Button Bolt
M6 x 37mm Bolt
Userʼs Manual
Large Foam Pad
Small Foam Pad
1
–
Note: Specifications are subject to change without notice. See the back cover of this manual for information
about ordering replacement parts. *These parts are not illustrated.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WEBE0878.0
R1008A
23
60
51
50
51
6
26
61
51
50
61
56
44
63
14
22
14
21
39
47
7
24
19
21
33
20
47
22
56
25
54
43
58
13
44
61
15
37
54
55
42
54
39
55
49
33
39
52
52
40
57
54
38
59
65
54
51
41
39
17
32
8
37
57
55
51
18
36
48
49
9
55
31
12
38
48
32
45
46
10
53
18
30
51
43
52
3
54
16
45
57
35
27
54
45
54
42
36
54
53
5
3
45
54
54
51
1
55
54
54
29
28
46
12
51
55
53
11
51
43
34
53
55
34
62
64
4
2
43
4
43
34
34
43
43
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement parts(s) (see the PART LIST and the EXPLODED DRAW-
ING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. Parts and labor are warranted for ninety (90) days
from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to
a service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip
charge. This warranty does not extend to any damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized
service center; products used for commercial or rental purposes; or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or
other consequential damages of whatsoever nature. Some states do not allow the exclusion or limita-
tion of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties
of merchantability or fitness for a particular purpose are limited in their scope and duration to the terms
set forth herein. Some states do not allow limitations on how long an implied warranty lasts.
Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 273326 R1008A
Printed in China © 2008 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|