R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PE550
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2002 Electrolux Home Products, Inc.
530163408
12/4/02
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
Blade can throw objects violently.
D You can be blinded or injured.
D Wears safety glasses or similar eye
protection.
Safety
Glasses
Boots
WARNING:
Hazard zone for thrown objects.
D Blade can throw objects violently.
D Others can be blinded or injured.
D Keep people and animals 50 feet (15 meters)
away.
Blade rotates
momentarily
after the
trigger is
released.
Allow blade to stop
before removing
it from the cut.
WARNING:
Blade rotates momentarily after the trigger is
released.
D The blade can seriously cut you or others.
D Allow blade to stop before removing it from
the cut.
WARNING:
Read instruction manual.
D Follow all warnings and instructions.
D Failure to do so can result in serious
injury.
Safety Labels
Instruction Manual
water heaters, electric motors or switches,
furnaces, etc.
FUEL SAFETY
S Mix and pour fuel outdoors and where there
are not sparks or flames.
S Store unit so blade cannot accidentally
cause injury.
S Always store gasoline in a container ap-
proved for flammable liquids.
S Do not smoke or allow smoking near fuel or
the unit; do not smoke while using the unit.
S Make sure the unit is properly assembled
and in good operating condition.
S Avoid spilling fuel or oil. Wipe up all fuel
spills before starting unit.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before re-
moving fuel cap.
S Do not store the unit with fuel in the fuel
tank; use up fuel left in the carburetor and
fuel line by starting the unit and letting it run
until it stops.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
TRANSPORTING AND STORAGE
S Do not grasp or hold exposed blade.
S Stop unit before leaving work area.
S Allow unit to cool, run fuel out of the fuel
tank, and secure the unit before storing or
transporting it in a vehicle.
S Before storing, use up fuel left in the carbu-
retor by starting the unit and letting it run un-
til it stops. Always allow the unit to cool be-
fore storage.
S Store unit out of reach of children.
If situations occur which are not covered in this
manual, use care and good judgment. If you
need assistance, call 1-800-554-6723.
SPECIAL NOTICE:
This unit is not
equipped with a temperature limiting muffler
and spark arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines be
equipped with a spark arrestor screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for installing
and maintaining the operating condition of
these parts. Failure to do so is a violation of
the law. If a spark arresting screen is re-
quired in your area, contact your authorized
service dealer for the correct kit.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
S Store unit and fuel in area where fuel vapors strength, change in skin color or texture, or
cannot reach sparks or open flames from loss of feeling in the fingers, hands, or joints,
3
Download from Www.Somanuals.com. All Manuals Search And Download.
discontinue the use of this tool and seek med- closely their physical condition and the condi-
ical attention. An anti-vibration system does tion of this tool.
not guarantee the avoidance of these prob-
SAVE THESE INSTRUCTIONS
lems. Users who operate power tools on a
continual and regular basis must monitor
ASSEMBLY
3. Thread one locknut onto each screw and
tighten securely.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554--6723.
This instruction manual has been developed
to help you assemble the unit and to provide
its safe operation. It is important that you read
the entire manual to become familiar with the
unit before you begin assembly.
Read your instruction manual.
Tools you will need:
S Adjustable wrench
S Hex wrench (provided)
TUBE ASSEMBLY
NOTE: When performing the following step,
be sure the handle is aligned as follows: label
on top, throttle trigger to the operator’s right
hand side. The starter rope and the throttle
cable must not wrap around the tube.
Handle tube
Screws
Lower
Tube
Starter Rope
Locknuts
NOTE: When performing the following step,
be sure the starter rope is not caught under
the cable clamp. The starter rope must hang
freely to operate properly.
4. Align the cable clamp between the tube
screws. Install the cable clamp around the
tube and throttle cable.
Label
Throttle trigger
Cable Clamp
1. Assemble handle tube to the lower tube (it
will be necessary to pull some of the start-
er rope out of the housing).
2. Align the screw holes; insert the screws
through the aligned holes.
Throttle cable
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR EDGER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the vari-
ous controls and adjustments. Save this manual for future reference.
Starter Rope Handle
ON/OFF
Fuel/Oil Mix Cap
Switch
Throttle Trigger
Choke
Depth
Control
Lever
Spark Plug
Air Filter
Primer Bulb
Muffler and
Depth
Guard
Blade Guard
Adjusting
Skid
Blade
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
ON/OFF SWITCH
The ON/OFF switch is used to select the ON
or OFF position.
STARTER ROPE HANDLE
The STARTER ROPE HANDLE is used for
starting the engine.CHOKEThe CHOKE pro-
vides additional fuel to the engine when start-
ing a cold or refueled engine.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. It is designed to be activated by the
right hand.
PRIMER BULB
BLADE
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer bulb
by pressing it and allowing it to return to its origi-
nal form.
The BLADE is designed to cut sod.
DEPTH ADJUSTING SKID
The DEPTH ADJUSTING SKID sets the
depth of the cut.
DEPTH CONTROL LEVER
The DEPTH CONTROL LEVER regulates
CHOKE
The CHOKE helps to supply fuel to the engine the cutting depth. Move the lever backward
to aid in cold starting. Activate the choke by for full depth edging, forward for half depth
moving the choke lever to the FULL CHOKE
edging.
oils will cause engine damage. When mixing
fuel, follow instructions printed on container.
Once oil is added to gasoline, shake contain-
er momentarily to assure that the fuel is thor-
oughly mixed. Always read and follow the
safety rules relating to fuel before fueling your
unit.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
IMPORTANT
FUELING ENGINE
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on un- age. Acidic gas can damage the fuel system
leaded gasoline. Before operation, gasoline of an engine while in storage. To avoid engine
must be mixed with a good quality synthetic problems, empty the fuel system before stor-
2-cycle air-cooled engine oil designed to be age for 30 days or longer. Drain the gas tank,
mixed at a ratio of 40:1. Poulan/Weed Eater start the engine and let it run until the fuel lines
brand synthetic oil is recommended. Mix gaso- and carburetor are empty. Use fresh fuel next
line and oil at a ratio of 40:1. A 40:1 ratio is ob- season.Never use engine or carburetor
tained by mixing 3.2 ounces (95 ml) of oil with cleaner products in the fuel tank or permanent
1 gallon (4 liters) of unleaded gasoline. DO damage may occur.See the STORAGE sec-
NOT USE automotive oil or boat oil. These tion for additional information.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
6. As soon as engine sounds as if it is trying
to start, move choke lever to the HALF
CHOKE position.
STOPPING YOUR ENGINE
S To stop a running engine, move the switch
to the OFF position.
S If engine does not stop, move choke lever
to FULL CHOKE position.
ON/OFF Switch
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. NOTE: If engine still doesn’t start, it
is probably flooded. Proceed to STARTING
A FLOODED ENGINE.
STARTING YOUR ENGINE
(for location of controls, refer to the KNOW
YOUR EDGER section)
S Fuel the engine; then move 10 feet (3 me-
ters) away from the fueling site.
8. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
OFF CHOKE. Allow the unit to run for 30
more seconds at OFF CHOKE before re-
leasing the throttle trigger. NOTE: If en-
gine dies with the choke lever in the OFF
CHOKE position, move the choke lever to
the HALF CHOKE position and pull the
rope until engine runs, but no more than 6
pulls.
DANGER: The cutting blade will
turn when the engine starts.
WARNING: Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
S Rest the unit on the ground. Support the
unit so the blade is off of the ground and
away from trees, bushes, onlookers, etc.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Move the choke lever to the HALF
CHOKE position.
STARTING
POSITION
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
5. Allow engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position. Release the throttle trigger.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded. Proceed to STARTING A
FLOODED ENGINE.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
Choke Lever
FULL
HALF
OFF
OPERATING INSTRUCTIONS
EDGING
4. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
As you become familiar with your edger, you
will be able to determine your own operating
pace. Conditions such as depth of cut and
material being cut will regulate the speed and
time required for your edging job.
S Allow the engine to warm up for one minute
before you begin edging.
S Increase the engine speed before placing
the blade in the cut. For best operation, run
the engine at full throttle while cutting.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S Keep you edging path straight by aligning
the blade guide rib on the rear of the blade
guard with the edge of the sidewalk. Keep
all wheels flat on the walkway.
NOTE: If the area to be edged has never
been cut or several weeks have passed since
the last cut, the first edging should be done at
no more than half depth.
To set the depth:
S Move the depth control lever forward for
shallower edging.
Blade
Guide Rib
S Move the depth control lever backward for
deeper edging.
Depth Control Lever
S Always work going away from people and
solid objects such as walls, large stones,
trees, automobiles, etc.
S Be careful when edging near trees or valu-
able plants. The high speed metal blade
may cut roots and cause damage to the
plants.
Depth
Adjusting
Skid
Support Arm
S If the blade stalls, immediately move the
unit rearward slightly to allow the blade to
restart. If the blade continues to stall, stop
the engine, disconnect the spark plug, and
inspect for blockage or damage.
S Always keep the blade area clean. Stop the
engine, make sure the blade has complete-
ly stopped turning, and disconnect the
spark plug before cleaning.
When edging, the trigger handle must be
raised until the skid rests on the ground. The
trigger handle must be held in the raised posi-
tion during the entire edging operation to
maintain a consistent edging depth.
DEPTH ADJUSTING SKID
The surface of the depth adjusting skid will
wear over a period of time. This part is revers-
ible to provide a second wear surface.
1. Remove the two mounting screws which
hold the skid to the support arm.
SETTING THE EDGING DEPTH
WARNING: Never attempt to adjust
the depth adjusting skid when the engine is
running. Always release the throttle trigger,
wait until the blade stops turning, move the
ON/OFF switch to the OFF position, and dis- S Inspect unit before each use.
connect spark plug before making adjust-
2. Rotate the skid 180 degrees.
3. Reinstall the mounting screws.
EDGING TIPS
S Inspect the area to be cut before each use.
ments. Your edger is equipped with several S Keep unit in front of your body.
edging depths. The depth used will depend S Cut at full throttle.
on your personal edging preference and the S Keep the wheels and skid in contact with
condition of the area where the edging opera-
tion is to be done.
the ground.
S Always work going away from others.
MAINTENANCE
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position and assure the engine
stops; then restart engine and continue.
S Fuel Tank -- Discontinue use of edger if fuel
tank shows signs of damage or leaks.
S Blade Guard -- Discontinue use of edger if
blade guard is damaged.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Blade nut
S Muffler
S Cylinder shield
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
S Once each year, replace the spark plug, re-
place air filter element and check blade for S Clutch
wear. A new spark plug and a clean/new air
filter element assures proper air/fuel mix-
ture and helps your engine run better and
last longer.
S Throttle trigger
S Handle screws
S Fasteners
INSPECT AND CLEAN UNIT & LA-
BELS
CHECK FOR DAMAGED OR
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Wipe off unit with a clean dry cloth.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAN AIR FILTER
BLADE MAINTENANCE
A dirty air filter decreases the life and perfor-
mance of the engine and increases fuel con-
sumption and harmful emissions.
WARNING: The blade will continue
to spin after the engine stops or after the
throttle trigger has been released. Make sure
the blade has stopped coasting and discon-
nect the spark plug before performing work on
the blade.
Always clean your air filter after 5 tanks of fuel
or 5 hours of operation, whichever comes
first. Clean more frequently in dusty condi-
tions. It is advisable to replace your air filter
with a new one after every 50 hours of opera-
tion, or annually, whichever comes first.
To clean filter:
WARNING: Wear protective gloves
when handling or performing maintenance on
the blade to help avoid injury.
Always replace a blade that is bent, warped,
cracked, broken, or damaged in any other
way. Never attempt to straighten and reuse a
damaged blade. Use only specified replace-
ment blade.
S The blade is reversible. When the cutting
edge on one side becomes worn, turn the
blade over.
S Check blade for flatness periodically. Lay
the blade on a flat surface to inspect for flat-
ness. Throw away a blade that is not flat.
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove the two screws and the air filter
cover from the engine.
3. Remove air filter.
NOTE: Do not clean the air filter with gaso-
line or other flammable solvent to avoid creat-
ing a fire hazard or producing harmful evapo-
rative emissions.
4. Clean the air filter using hot soapy water.
Rinse with clean cool water. Air dry com-
pletely before reinstalling.
5. Lightly oil air filter before installing to im-
prove the efficiency of the air filter. Use
2--cycle engine oil or motor oil (SAE 30).
NOTE: Do not soak air filter in oil.
6. Squeeze the air filter to distribute oil and to
remove any excess oil.
REPLACE SPARK PLUG
The spark plug should be replaced each year
to ensure the engine starts easier and runs
better. Set spark plug gap at 0.025 inches.
Ignition timing is fixed, nonadjustable.
1. Twist then pull off the spark plug boot.
2. Remove and discard the spark plug.
3. Replace with Champion RCJ--6Y spark
plug and tighten securely with a wrench.
4. Reinstall the spark plug boot.
7. Reinstall air filter in housing.
CAUTION: Make sure air filter is fitted in to
the corners of the housing to prevent air from
bypassing the filter and to keep dust from en-
tering engine and causing damage.
8. Reinstall air filter cover.
Spark Plug Boot
Air Filter
Cover
Spark Plug
Cover
Screws
SERVICE AND ADJUSTMENTS
BLADE REPLACEMENT
2. Align the flat area of the blade opening with
the flat side of the shaft. Place the new
blade on the shaft.
1. To remove the blade, insert a screwdriver
into the hole in the gearbox; then, remove
the nut, washer, and blade from the blade
shaft.
Nut
Hole
Flat sides
Washer
3. Install the washer and nut; turn nut coun-
terclockwise on the blade shaft.
4. Bind blade by inserting a screwdriver in to
the hole in the gearbox; then, firmly tighten
nut with a wrench.
Blade
8
Download from Www.Somanuals.com. All Manuals Search And Download.
S Turn idle speed screw counterclockwise to
decrease engine speed if the blade shaft
spins at idle speed.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The blade
shaft will be spinning during most of this pro-
cedure. Wear your protective equipment and
observe all safety precautions. After making
adjustments, the blade shaft must not spin at
idle speed.
WARNING: Recheck the idle speed
after each adjustment. The blade shaft must
not spin at idle speed to avoid serious injury to
the operator or others.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
S The blade spins at idle.
Keep others away when making idle speed
adjustments. Remove the blade before mak-
ing carburetor idle speed adjustments. Do not
make adjustments from the blade side of the
unit. Recheck the idle speed after each ad-
justment. The blade must not spin at idle
speed to avoid serious injury to the operator
or others. Make adjustments with the unit
supported so the blade is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the blade and muffler.
Idle Speed
Adjustment
Screw
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without the blade shaft spinning (idle too If you require further assistance or are unsure
fast) or engine stalling (idle speed too slow). about performing this procedure, contact an
S Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies. 1--800--554--6723.
authorized
service
dealer
or
call
STORAGE
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool before storing or trans-
porting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S Clean the entire unit before lengthy stor- S At the beginning of the next season, use
age.
only fresh fuel having the proper gasoline to
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
OTHER
FUEL SYSTEM
S Do not store gasoline from one season to
another.
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S Replace your gasoline can if it starts to rust.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start or will run
only a few
seconds after
starting.
1.ON/OFF switch in OFF
position.
2. Engine flooded.
1. Move ON/OFF switch to the ON
position.
2. See “Difficult Starting” in
Operation Section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6.Compression low.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build up.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine
1. Choke partially on.
smokes
2. Fuel mixture incorrect.
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
Engine runs
hot.
1. Fuel mixture incorrect.
1. See “Fueling Engine” in Operation
section.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
2. Replace with correct plug.
3. Contact an authorized service dealer.
4. Carbon build-up.
4. Contact an authorized service dealer.
Blade turns at
idle speed.
1. Carburetor requires
adjustment.
2. Throttle cable binding.
3. Clutch requires repair.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Replace or repair throttle cable.
3. Contact an authorized service dealer.
1. Check gearbox.
Blade stops un-
der a load or
does not turn
when engine is
accelerated.
1. Blade not engaged.
2. Carburetor requires
adjustment.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
3. Clutch requires repair.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
THIS WARRANTY GIVES YOU SPECIFIC
warrants to the original purchaser that each new LEGAL RIGHTS, AND YOU MAY HAVE
Weed Eaterr brand gasoline tool or attach- OTHER RIGHTS WHICH VARY FROM
ment is free from defects in material and work- STATE TO STATE.
manship and agrees to repair or replace under NO CLAIMS FOR CONSEQUENTIAL OR
this warranty any defective gasoline product or OTHER DAMAGES WILL BE ALLOWED,
attachment as follows from the original date of AND THERE ARE NO OTHER EXPRESS
purchase.
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
2 YEARS--Parts and Labor, when used for
household purposes.
SOME STATES DO NOT ALLOW LIMITA-
90 DAYS--Parts and Labor, when used for com- TIONS ON HOW LONG AN IMPLIED WAR-
mercial, professional, or income producing pur- RANTY LASTS OR THE EXCLUSION OR
poses.
LIMITATIONS OF INCIDENTAL OR CONSE-
30 DAYS--Parts and Labor, if used for rental QUENTIAL DAMAGES, SO THE ABOVE
purposes.
LIMITATIONS OR EXCLUSION MAY NOT
This warranty is not transferable and does not APPLY TO YOU.
cover damage or liability caused by improper The policy of ELECTROLUX HOME PROD-
handling, improper maintenance, or the use of UCTS, INC., is to continuously improve its
accessories and/or attachments not specifically products. Therefore, ELECTROLUX HOME
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally, change, modify, or discontinue models, de-
this warranty does not cover tune-ups, spark signs, specifications, and accessories of all
PRODUCTS, INC., reserves the right to
plugs, filters, etc., that will wear and require re- products at any time without notice or obliga-
placement with reasonable use during the war- tion to any purchaser.
ranty period. This warranty does not cover pre-
delivery setup or normal adjustments explained
in the instruction manual.
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
failure to ensure the performance of all sched-
TIONS: The U. S. Environmental Protection uled maintenance. As the small off--road en-
Agency and ELECTROLUX HOME PROD- gine owner, you should be aware that ELEC-
UCTS, INC., are pleased to explain the emis- TROLUX HOME PRODUCTS, INC., may deny
sions control system warranty on your year you warranty coverage if your small off--road
2002--2004 small off--road engine. ELECTRO- engine or a part of it has failed due to abuse, ne-
LUX HOME PRODUCTS, INC., must warrant glect, improper maintenance, unapproved mod-
the emission control system on your small off-- ifications, or the use of parts not made or ap-
road engine for the periods of time listed below proved by the original equipment manufacturer.
provided there has been no abuse, neglect, or You are responsible for presenting your small
improper maintenance of your small off--road off--road engine to an ELECTROLUX HOME
engine. Your emission control system includes PRODUCTS, INC., authorized repair center as
parts such as the carburetor and the ignition soon as a problem exists. Warranty repairs
system. Where a warrantable condition exists, should be completed in a reasonable amount of
ELECTROLUX HOME PRODUCTS, INC., will
time, not to exceed 30 days. If you have any
repair your small off--road engine at no cost to questions regarding your warranty rights and re-
you. Expenses covered under warranty include sponsibilities, you should contact your nearest
diagnosis, parts and labor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any emis-
authorized service center or call ELECTRO-
LUX HOME PRODUCTS, INC., at
sions related part on your engine (as listed un- 1--800--554--6723.
WARRANTY COM-
der Emissions Control Warranty Parts List) is
MENCEMENT DATE: The warranty period be-
defective or a defect in the materials or work- gins on the date the small off--road engine is
manship of the engine causes the failure of such purchased. LENGTH OF COVERAGE: This
an emission related part, the part will be repaired warranty shall be for a period of two years from
or replaced by ELECTROLUX HOME PROD-
the initial date of purchase. WHAT IS COV-
UCTS, INC. OWNER’S WARRANTY RE-
ERED: REPAIR OR REPLACEMENT OF
SPONSIBILITIES: As the small off--road en- PARTS. Repair or replacement of any war-
gine owner, you are responsible for the
ranted part will be performed at no charge to the
performance of the required maintenance listed owner at an approved ELECTROLUX HOME
in your instruction manual. ELECTROLUX
HOME PRODUCTS, INC., recommends that
PRODUCTS, INC., servicing center. If you
have any questions regarding your warranty
you retain all receipts covering maintenance on rights and responsibilities, you should contact
your small off--road engine, but ELECTROLUX your nearest authorized service center or call
HOME PRODUCTS, INC., cannot deny war-
ELECTROLUX HOME PRODUCTS, INC., at
ranty solely for the lack of receipts or for your 1--800--554--6723.
WARRANTY PERIOD:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Any warranted part which is not scheduled for use of add--on or modified parts. HOW TO FILE
replacement as required maintenance, or which A CLAIM: If you have any questions regarding
is scheduled only for regular inspection to the ef- your warranty rights and responsibilities, you
fect of “repair or replace as necessary” shall be should contact your nearest authorized service
warranted for 2 years. Any warranted part which center or call ELECTROLUX HOME PROD-
is scheduled for replacement as required main- UCTS, INC., at 1--800--554--6723. WHERE TO
tenance shall be warranted for the period of time GET WARRANTY SERVICE: Warranty ser-
up to the first scheduled replacement point for vices or repairs shall be provided at all ELEC-
that part. DIAGNOSIS: The owner shall not be TROLUX HOME PRODUCTS, INC., service
charged for diagnostic labor which leads to the centers. Call 1--800--554--6723. MAINTE-
determination that a warranted part is defective NANCE, REPLACEMENT AND REPAIR OF
if the diagnostic work is performed at an ap- EMISSION RELATED PARTS: Any ELEC-
proved ELECTROLUX HOME PRODUCTS,
INC., servicing center. CONSEQUENTIAL
DAMAGES: ELECTROLUX HOME PROD-
TROLUX HOME PRODUCTS, INC., approved
replacement part used in the performance of
any warranty maintenance or repair on emis-
UCTS, INC., may be liable for damages to other sion related parts will be provided without
engine components caused by the failure of a charge to the owner if the part is under warranty.
warranted part still under warranty. WHAT IS EMISSION CONTROL WARRANTY PARTS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov- (covered up to maintenance schedule), Ignition
ered. ADD--ON OR MODIFIED PARTS: The Module. MAINTENANCE STATEMENT: The
LIST: Carburetor, Ignition System: Spark Plug
use of add--on or modified parts can be grounds owner is responsible for the performance of all
for disallowing a warranty claim. ELECTRO- required maintenance as defined in the in-
LUX HOME PRODUCTS, INC., is not liable to
cover failures of warranted parts caused by the
struction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|