Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking web site at
vikingrange.com
Microwave Built-In Trim Kit
F20196C EN
(010708J)
TINSEB453MRRO
Download from Www.Somanuals.com. All Manuals Search And Download.
CABINET OR WALL CUTOUT
CABINET INSTALLATION
Cutout Dimensions
1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
Height (A)
2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly. See
Illustration 3. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the
feet of the oven are fitted into the recesses of the Exhaust Duct Assembly. See Illustration 4.
Minimum
Maximum
Width (B)
16 3/4” (42.5 cm)
17” (43.2 cm)
Minimum
Maximum
24 3/8” (61.9 cm)
24 11/16” (62.7 cm)
Depth (C)
Minimum
Illustration 4
20” (50.8 cm)
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as
indicated on Illustration 1
Illustration 3
6”
OVEN
SIDE
(15.2 cm)
NOTE 1: If the Depth (C) dimension is greater
than 21” (53.3 cm), the outlet location may be in
any area on the rear wall.
Foot
4”
(10.2 cm)
Recess
NOTE 2: The floor of the opening should be
constructed of plywood strong enough to support
the weight of the oven and floor load
(approximately 100 pounds). The floor should be
level for proper operation of the oven. Be sure to
check the local building code as it may require that
the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does
not require the enclosure.
Exhaust Duct Assembly
4”
(10.2 cm)
FRAME INSTALLATION
VMTK ONLY
Illustration 1
EXHAUST DUCT ASSEMBLY
1. Place the Exhaust Duct in the opening.
When the Exhaust Duct Assembly is in the
opening correctly, the flanges will be tightly
against the lower edge of the opening. See
Illustration 2.
Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven.
Check that it is level and then secure with two SCREWS B. See Illustration 5. Secure the bottom portion of the FRAME
ASSEMBLY with the two remaining SCREWS B. See Illustration 5.
Illustration 2
2. Secure the Exhaust Duct Assembly with the
two (1/2”) screws A. IMPORTANT: Secure
screws in outer hole.
Illustration 5
Screw B
Flanges
Screw B
Screw B
Exhaust Duct Assembly
Screw B
5
Detail A
Screw A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DMTK300 ONLY
DMTK270 ONLY
OVER OVEN INSTALLATION
Position the BACK FRAME ASSEMBLY to be square with
the oven. Carefully place the BACK FRAME ASSEMBLY
on the oven. Check that the oven is level and secure the
upper portion FIRST with two of the Screw B. Secure the
bottom portion of the BACK FRAME ASSEMBLY with the
remaining two Screws B. See Illustration 5
Position the BACK FRAME ASSEMBLY to be square with
the oven. Carefully place the BACK FRAME ASSEMBLY
on the oven. Check that the oven is level and secure the
lower portion FIRST with two of the Screw B. Adjusting
the BACK FRAME ASSEMBLY up or down may be
necessary in order to locate the thru holes on the exhaust
duct assembly. Secure the upper portion of the BACK
FRAME ASSEMBLY with the remaining Screw B. See
Illustration 5
2” (5.1 cm) For 27” W. and 30” W. lower oven
4” (10.2 cm) For 36” W. lower oven
Illustration 5
Screw B
Place the FRONT FRAME ASSEMBLY through the microwave onto the BACK FRAME ASSEMBLY. Secure the FRONT
FRAME ASSEMBLY to the BACK FRAME ASSEMBLY with Screws C. See Illustration 6
NOTE: The center tab denotes correct orientation of the FRONT FRAME. See Detail B.
Illustration 6
Detail B
Screw C
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|