DIGITAL VIDEO
HDD/DVD VIDEO RECORDER
RD-XS35SU
RD-XS35SC
OWNER’S MANUAL
INSTALLATION
GUIDE
Read this booklet first.
P000453930
PM0025865010
H
© 2006 Toshiba Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Note to cable system installer:
This reminder is provided to call the cable system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as practical.
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the
risk of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your recorder.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
PRODUCT IS CERTIFIED BYTHE
MANUFACTURER TO COMPLY
WITH DHHS RULE 21 CFR
SUBCHAPTER J IN EFFECT AT
DATE OF MANUFACTURE.
1-1,SHIBAURA 1-CHOME,MINATO-KU,
TOKYO 105-8001,JAPAN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10.Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
4. Follow all instructions.
11.Only use attachments/accessories specified by
the manufacturer.
5. Do not use this apparatus near water.
12.Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
S3125A
13.Unplug this apparatus during lightning storms
or when unused for long periods of time.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
14.Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
21.Do not use a cracked, deformed, or repaired
disc. These discs are easily broken and may
cause serious personal injury and apparatus
malfunction.
ADDITIONAL SAFETY INSTRUCTIONS
15.Do not overload wall outlets; extension cords,
or integral convenience receptacles as this can
result in a risk of fire or electric shock.
22.If the apparatus should smoke or smell,
immediately disconnect the power cord from the
wall outlet. Wait until the smoke or smell stops,
then ask your dealer for a check and repair.
Neglecting to do so may cause fire.
16.Apparatus should not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, should not be placed on the
apparatus.
23.During thunderstorms, do not touch the
connecting cables or the apparatus.
17.Keep your fingers well clear of the disc tray as
it is closing. Neglecting to do so may cause
serious personal injury.
24.The apparatus includes lead, an ingredient of
solder used on the PCB, which is a harmful
substance to human and the environment. When
disposing of this apparatus, follow the rules and
regulations in your area.
18.Do not place anything on top of this unit.
19.Do not place the apparatus on amplifiers or
equipment that may produce heat.
20.Do not cover the ventilating holes for the inside
cooling fan.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions
Notes on handling
Notes on cleaning
Never disconnect the power cord from a wall outlet
while the recorder is not in standby mode, unless it is
in an emergency. Doing so may cause malfunction.
When shipping the recorder, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the recorder. Do not leave rubber or plastic products in
contact with the recorder for a long time. They will
leave marks on the finish.
Use a soft, dry cloth for cleaning.
Do not use any type of solvent, such as thinner or
benzine, as they may damage the surface of the
recorder.
Notes on antennas
Image and sound quality depend very much on signal
reception.
Reception may be poor in weak signal areas. In this
event, consult your dealer, or purchase a commercially
available antenna booster. Refer to the booster’s
instruction manual for installation details.
The top and rear panels of the recorder may become
warm after a long period of use. This is not a
malfunction.
When not in use
For usual absence
Be sure to remove the disc from the recorder and turn
off the power.
Prolonged absence
Unplug the recorder from a wall outlet.
Notes on locating
Place the recorder on a level surface. Do not use it on
a shaky or unstable surface such as a wobbly table or
inclined stand. The loaded disc may dislodge from its
proper position and cause damage to the recorder.
Before placing the recorder, make sure that the
surface can stand the weight of the recorder. Never
place the recorder in a high location to avoid damage
to the product or person by an accidental fall of the
recorder.
When you place this recorder near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted depending on the condition
and location of said equipment. In such an event,
place the recorder as far away much as possible from
the TV, radio, or VCR.
To avoid damage to this product, never place or store
the unit in direct sunlight; hot, humid areas; or areas
subject to excessive dust, oily smoke, cigarette smoke
or vibration.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on recording and editing
Power outage
When you record/edit important content, make trial
operations beforehand to confirm the recorder can
function properly.
After a power outage the clock display will flash. Set
the clock to the correct time.
Toshiba does not compensate for content which was
not recorded/edited because of some malfunction of
this product or discs during operation, and is not liable
for incidental damages (such as profit loss or
interruption of business, etc.) produced in such
conditions.
When the power cord is disconnected or when a
power failure occurs during any operation of this
product, all contents recorded in this recorder may be
erased.
Notes on the unit and the HDD
Do not give a shock or shake (especially during
operation).
Do not use in a shaky or unstable location.
Hold the unit horizontally.
Do not cover the ventilation holes for the cooling fan of
the unit.
Do not use in a place where the temperature rises or
changes rapidly.
Do not disconnect the power plug from a wall outlet
while the unit is turned on.
Depending on the channel or program, an excessive
sound input level may cause noise or cut of recorded
sound. Adjust the initial setting of the recording level
when necessary.
Do not disconnect the power plug from the wall outlet
or break the power supply to the unit during recording
or playing. Before disconnecting the power plug, be
sure to press the power button and make sure the unit
ends the finishing process and power turns off
(standby mode). If the power plug is disconnected or
power supply is disrupted while the unit is recording,
all recorded content will be erased.
If a program you have set a timer recording includes
copy restriction signals, it may not be recorded. When
programming a recording, confirm that a program you
want to record is not copy-restricted.
Exemptions
Toshiba is not liable for any damage or loss of
recorded data caused by shock, shakes, misoperation
or malfunction.
Toshiba is not liable for any damage caused by fires,
natural disaster (such as thunder, earthquake, etc.),
acts by third parties, accidents, owner’s intentional or
unintentional misuse, or uses in other improper
conditions.
Toshiba is not liable for incidental damages (such as
profit loss or interruption in business, modification or
erasure of recorded data, etc.) caused by use or
inability to use of this product.
Toshiba is not liable for any damage caused by
neglect of the instructions described in the owner’s
manual.
Toshiba is not liable for any damage caused by
misuse or malfunction through simultaneous use of
this product and the connected equipment or software
that Toshiba is not concerned with.
Toshiba does not compensate for contents which were
not recorded/edited because of some malfunctions of
this product or discs during operation, and is not liable
for incidental damages (such as profit loss or
interruption in business, etc.) produced by such
conditions.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Precautions (Continued)
Notes on moisture condensation
Moisture condensation damages the unit. Please
read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens inside
this unit, one of the most crucial internal parts of the unit.
o
f
n
s
Optical pick-up
lens
Moisture condensation occurs during the
following cases.
When you bring the unit directly from a cold place to a
warm place.
When you use the unit in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the unit in a hot and humid
place just after you move the unit from an air
conditioned room.
When you use the unit in a humid place.
Do not use the unit when moisture condensation
may occur.
If you use the unit in such a situation, it may damage
discs and internal parts. Connect the power cord of
the unit to the wall outlet, turn on the unit, remove the
disc, and leave it for two or three hours. After two or
three hours, the unit will have warmed up and
evaporated any moisture. Keep the unit connected to
the wall outlet and moisture condensation will seldom
occur.
Wall outlet
8
Download from Www.Somanuals.com. All Manuals Search And Download.
In the United States, TV Guide and other related marks
are registered marks of Gemstar-TV Guide International,
Inc. and/or one of its affiliates. In Canada, TV Guide is a
registered mark of Transcontinental Inc., and is used
under license by Gemstar-TV Guide International, Inc.
Program
Recording
Copy
DVD-RAM
disc
HDD
Can be
recorded
Can be
copied
DVD-R/RW
Content is not
copyright
protected
The TV Guide On Screen system is manufactured under
license from Gemstar-TV Guide International, Inc. and/or
one of its affiliates.
DVD-RAM
disc
HDD
The TV Guide On Screen system is protected by one or
more of the following issued United States patents
6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203;
5,940,073; 4,908,713; 4,751,578; 4,706,121.
Can be
recorded
Can be
copied
DVD-R/RW
Content is not
copyright
protected
Manufactured under license from QSound Labs, Inc.
U.S. patent Nos. 5,105,462, 5,208,860 and 5,440,638
and various foreign counterpart. Copyright QSound Labs,
Inc. 1998-2002. QXpanderTM is a trademark of QSound
Labs, Inc. All rights reserved.
DVD-RAM
disc
HDD
Can be
recorded
Cannot be
copied
DVD-R/RW
Recording
permitted once
DVD-RAM
disc
HDD
Can be
recorded
Cannot be
copied
Recording
permitted once
DVD-R/RW
Cannot be
recorded
Recording
permitted once
HDD
Cannot be
recorded
Recording prohibited
DVD-RAM
disc
Cannot be
recorded
DVD-R/RW
HDD:Hard Disc Drive
Recording prohibited
Content that can be recorded once can only move from
the HDD to a DVD-RAM disc. (The original one is
deleted after moving to a DVD-RAM disc.)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Installation procedure
Accessories
Read carefully “SAFETY PRECAUTIONS”,
“IMPORTANT SAFETY INSTRUCTIONS” and
“Precautions”.
Remote control
Batteries (AAA) x 2
(
pages 2 to 9)
Coaxial cable
Check the supplied accessories.
(See right)
Load the batteries in the remote control.
Video/Audio cable
(
page 18)
Connect an antenna to the recorder.
page 20)
(
G-LINK® cable
Connect a cable box or satellite system to the recorder.
pages 22 to 25)
(
Connect the recorder to a TV.
pages 20 to 21, 26)
(
• Owner’s manual
(INSTALLATION GUIDE)
• Owner’s manual
(OPERATIONS GUIDE)
Connect optional equipment to the recorder.
page 27)
(
Set up the TV Guide On Screen® interactive
program guide. ( page 32)
Your recorder is ready. Read the separate
volume “OPERATIONS GUIDE”.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this product
Playback Restrictions
Some differences
This owner’s manual explains the basic instructions for
this recorder. Some DVD video discs are produced in a
manner that allows specific or limited operation during
playback. As such, the recorder may not respond to all
operating commands. This is not a defect in the
recorder. Please refer to the notes on compatible discs
later in this Introduction and to the discussion of DVD
playback and features later in this manual.
Because of its recording capacity and hard disc drive
(HDD), this DVD recorder operates more like a
computer and differently than a standard DVD player. In
addition to containing a microprocessor, it contains a
HDD, an operating system, random access memory
(RAM), and a DVD-RAM/R/RW drive. The operating
system includes software stored on the HDD that is
transferred to the RAM when the machine is turned on
and at other times during operation. This transfer can
take time. Therefore, when you turn the DVD recorder
on, it may take a little while before it is ready to use.
Likewise, other functions may not be performed as
quickly as they would on other AV equipment.
“
“
” may appear on the TV screen during operation.
” means that the operation is not permitted by the
recorder or the disc.
Additionally, because programs stored on the DVD-
RAM/R/RW drive cannot be accessed as quickly as
those stored on the HDD, accessing those programs (or
deleting a program from a DVD-RAM disc) may take
more time. Please take these factors into consideration
as you use the DVD recorder.
Recording Restrictions and Copyright
Copy-protected contents of DVD-Video discs, VIDEO
CDs or audio CDs on the market cannot be copied on
this recorder. Contents without copy protection should
be copied or edited only in accordance with applicable
copyright laws, which may restrict copying or editing.
Contents that permit single copying (copy once
contents) can be recorded onto DVD-RAM discs, with
some dubbing and editing restrictions. DVD-R/RW discs
cannot record these contents.
The unauthorized recording, use, distribution, or
revision of copyrighted materials including, without
limitation, television programs, videotapes, and DVDs,
is prohibited under the Copyright Laws of the United
States and other countries, and may subject you to civil
and criminal liability.
About the hard disc drive (HDD)
Like any HDD, the HDD in the DVD recorder is a fragile
device that is susceptible to partial or complete failure if
it is jarred or as a result of use over time. It will not last
forever. Therefore, do not use the HDD for longer term
storage of programs you wish to retain. [If portions of
the HDD become damaged, programs recorded on
those portions may exhibit pixelization or block noise
when played back. Repeated playback of the program
may cause the problem to get worse and, eventually, the
program may become unplayable. Accordingly, if you
notice such noise in a program that you want to save,
you should transfer to a recordable DVD disc as soon as
possible.] Recordable DVD discs are also susceptible
to damage if not handled and stored carefully and some
or all of the programs on them may become unplayable.
You can reduce these risks by using high quality DVD
recordable discs and checking their playability from time
to time. If it becomes necessary to service your DVD
recorder, it may be necessary to delete some or all of
the programs on the HDD.
Compatibility
In isolated cases, a disc bearing the DVD or CD logo
may not fully and properly play back all features or as
intended by the creator of the disc. This can be due,
among other reasons, to problems and errors that can
occur during the creation or recording of DVD and other
software and the manufacture of software discs
(including blank discs). Moreover, because of
variations in the quality of discs, this recorder may not
be able to record on all discs that bear a DVD-RAM,
DVD-R or DVD-RW logo, but you should not encounter
difficulty if you use only high quality recordable DVD
discs. Additionally, discs recorded in this device may not
operate properly in other DVD players, recorders and/or
personal computer drives. If you happen to encounter
difficulties playing or recording a DVD disc or playing a
CD disc, please feel free to call our Customer Service
Hotline at 1-800-319-6684.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Choosing a disc
When you want to play DVD or CD software or copy programs from the HDD to a recordable DVD, load an
appropriate disc into the recorder. There are many types and formats of discs. Please use the following
information to select an appropriate disc.
Notes
• Handle the disc according to the disc instruction manual.
• Toshiba cannot guarantee that all discs bearing the DVD or CD logos will operate as expected. Additionally, Toshiba cannot
guarantee that discs recorded in this device will operate properly in other DVD players, recorders and/or personal computer
drives.
For recording / playback
Disc
Mark
Specification
Remarks
• Single sided 4.7GB (12cm (43/4 in.))
Read carefully the section “On DVD-RAM
DVD-RAM
• Double sided 9.4GB (12cm (43/4 in.))
discs” (
page 14).
Select a DVD-RAM disc that shows a
statement on its package such as “this disc
can be used with video recorders and drives
compatible with 4.7GB DVD-RAM discs” or
“this disc can copy images that permit single
copying.”
• 4.7GB For General Ver.2.0
Read carefully the section “On DVD-R discs”
DVD-R
(12cm (43/4 in.))
(
page 15).
Depending on the disc status or the
recording equipment, playback of the disc
may not be possible on this recorder.
• Ver. 1.1 or later (12cm
Read carefully the section “On DVD-RW
DVD-RW
(43/4 in.))
discs” (
page 15).
Depending on the disc status or the
recording equipment, playback of the disc
may not be possible on this recorder.
Using different disc types for different purposes
DVD-RAM discs for your personal library
DVD-RAM discs comply with the global standard DVD-VR (Video Recording) format, and are optimized for recording of
TV programs.You can rewrite repeatedly without deterioration of an image quality, erase unnecessary parts, divide a
chapter, or specify playback area by frame. Its cartridge is suitable for a longer-term storage and family use, and its
large capacity of 9.4 GB allows more recording space.
DVD-R/RW discs when creating your own original discs for distribution
DVD-R discs are designed to comply with the global standard DVD-Video format, and can be recorded only once. DVD-
R discs are convenient when you edit your original content (recorded personal events such as a wedding party) with
this recorder, transfer them to the recorder and make copies to send to your friends or relatives. The discs can be
played on other compatible DVD players. DVD-RW discs, which are rewritable, can be used as well.
* DVD-R and DVD-RW may not be the best suited format for recording TV programs. Because of the way the discs are
formatted, it may not be possible to edit or divide the program as you may prefer, to record secondary languages, or
programs that are copy protected in a way that allows only one copy. (NOTE: “Copy once” protected programs
generally can be recorded to DVD-RAM discs.)
* This recorder records on a DVD-R/RW disc in DVD-Video format only.
* On DVD-R/RW discs, direct recording, copying or the method “Creating a DVD-Video using DVD-R/RW” (
page
112 in “OPERATIONS GUIDE”) are available.
We cannot guarantee that DVD-RAM/R/RW discs recorded on this recorder will be playable on all DVD recorders/
players. Similarly, there is no guarantee that all DVD-RAM/R/RW discs recorded on other recorders will be playable on
this recorder.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
For playback only
Disc
Mark
Specification
Remarks
DVD video
disc
• 12cm (43/4 in.) / 8cm (31/4 in.)
• Region number
The region number of this DVD recorder is 1.
If region numbers, corresponding to a
specific playable area, are printed on your
1
DVD video disc and you do not find
or
or
1
ALL
ALL
, or the disc is encoded to permit
playback only in regions other than Region 1,
disc playback will not be allowed by the
recorder.
• Color system: NTSC
• 12cm (43/4 in.) / 8cm (31/4 in.)
• Color system: NTSC
VIDEO CD
• Version 1.1 and 2.0
DIGITAL VIDEO
Audio CD
• 12cm (43/4 in.) / 8cm (31/4 in.)
CD-R
• 12cm (43/4 in.)
• CD-DA (audio CD) format
Depending on the disc status, playback may
not be possible.
CD-RW
• You cannot play discs other than those listed above.
• You cannot play non-standardized discs even if they may be labeled as above.
• You cannpË»play discs with specialized encoding (such as SACD discs) or the DVD audio êortions of DVD Audio
discs.
• This recorder uses the NTSC color system, and cannot play DVD video discs recorded in any other color system
1
ALL
(PAL, SECAM, etc.), even if they have region marks
• Toshiba cannot guarantee that all discs bearing the DVD or CD logos will operate as expected. Please see the
discussion of compatibility on page 11.
or
.
• Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction of this recorder,
including, without limitation, any one of the following:
• Failure to record contents intended to be recorded by the consumer.
• Failure to edit contents as intended by the consumer.
• When a DVD-RAM disc or a DVD-R/RW disc created on this recorder is used (e.g., insertion, playback,
recording or editing) in another DVD player, recorder or personal computer drive.
• When a DVD-RAM disc or a DVD-R/RW disc that is used in the manner described in the immediately
preceding bullet point is used again in this recorder.
• When a DVD-RAM disc or a DVD-R/RW disc that was recorded in another DVD recorder, or in a personal
computer drive is used in this recorder.
• Some functions such as Library may not work with personal computer discs.
• Discs recorded in this recorder may not operate as expected on other DVD players, recorders or personal
computer drives.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Choosing a disc (Continued)
On DVD-RAM discs
To protect recorded contents
Slide the write-protect tab to
“PROTECT” with something small
enough. The disc can play, but
cannot be edited or erased. Refer
to the instructions that come with
the disc.
Use only DVD-RAM discs that comply with
DVD-RAM standard Version 2.0, 2.1 or 2.2.
The recorder cannot record on a disc formatted in any
other standard. When using such a disc, initialize it by
using the disc-format function of this recorder.
The recorder may not record, dub, or edit some DVD-
RAM discs, because they are edited/recorded with
another manufacturer’s equipment or PC, contain a
large number of titles, or have little remaining capacity.
Also, a DVD-RAM disc may not be edited or recorded
if its title contains still pictures.
PROTECT
When using a disc without a
cartridge (commercially
available discs)
Discs without cartridges can easily
attract fingerprints and dust, which
DVD-RAM discs formatted in UDF2.0 on a PC are not
compatible with this recorder. Before using these
discs, initialize them on this recorder.
is the reason they are not recommended. If you cannot
avoid using them, handle with proper care.
When you write in a title column on a disc, use a pen
with a soft tip. Do not use a pen with a hard tip, such
as a ballpoint pen.
This recorder complies with current copyright
protection technology and can copy a disc only when
the disc permits copying once. When there is no
indication on the disc, copying will not be allowed.
Such an indication on a disc is required also for the
Library Management database.
Recommended discs
The following discs have been tested with this recorder:
9.4 GB double-sided cartridge: Panasonic 2X, 3X, 5X
4.7 GB single-sided cartridge: Panasonic 2X, 3X, 5X
DVD-RAM discs with cartridges are
recommended for recording.
Two types of DVD-RAM discs are
available: ones with cartridges and ones
without cartridges.You can use either of
them with this recorder, but the former
ones are recommended.
In order to record highly detailed data, make sure the
disc is clean. DVD-RAM discs with cartridges are
easier to handle in this regard.
Do not open the cartridge shutter. The disc may not
play, or may not be recorded or edited once it
becomes dirty.
There are two types of DVD-RAM cartridges;
removable (TYPE 2/4) and not removable (TYPE 1). It
is recommended you do not remove the disc even
when you can.
Refer to the instruction manual that comes with the
disc if it is absolutely necessary to remove the disc.
Some commercially available cartridge discs cannot
be recorded or edited once the inside discs are
removed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
On DVD-R discs
Marks on DVD video discs
The following are examples of marks and the meanings.
Standards
DVD-R for General Ver.2.0 discs can be used for
recording and playback.
Discs compatible with the following recording speeds
Mark
Meanings
can also be used:
Ver. 2.0/2X
Ver. 2.0/4X
Ver. 2.0/8X
Ver. 2.0/16X
Number of audio streams
recorded in the disc.
(2 streams such as English and
Japanese in this example.)
2
Select discs labeled “for video,” “for recording,” “120
min.” etc.
Number of subtitle languages
recorded in the disc.
(2 subtitle languages are
recorded in this example.)
2
3
Recording conditions
Images for which copying is prohibited or restricted
(copy once or copy prohibited) cannot be recorded.
Even if the disc is labeled as CPRM compatible, this
recorder can only be used to record copy-free
material.
Number of camera angles
recorded in the disc.
(3 camera angles are recorded in
this example.)
DVD-VR mode recording is not possible.
Recommended discs
That’s (Taiyo-Yuden) 4X, 8X, 16X
Pictures are recorded in the
standard picture shape
(4:3 aspect ratio).
4:3
LB
On DVD-RW discs
Pictures are recorded in the letter
box picture shape (4:3 aspect
ratio with horizontal black bars in
the top and bottom of pictures).
Standards
Discs labeled DVD-RW Ver.1.1 or 1.2 can be used.
Discs compatible with the following recording speeds
can also be used:
Ver. 1.1/2X
Ver. 1.2/4X
Ver. 1.2/6X
Pictures are recorded in the 16:9
wide picture shape.
TVs with 4:3 aspect ratio will
display them in the letter box
style.
16:9 LB
16:9 PS
Select discs labeled “for video,” “for recording,” “120
min.” etc.
Recording conditions
Pictures are recorded in the 16:9
wide picture shape.
TVs with 4:3 aspect ratio will
display them in the pan scan style
(one or both sides of pictures
are cut).
Images for which copying is prohibited or restricted
(copy once or copy prohibited) cannot be recorded.
Even if the disc is labeled as CPRM compatible, this
recorder can only be used to record copy-free
material.
DVD-VR mode recording is not possible.
Recommended discs*
JVC 2X, 4X, 6X
Actual picture shape may vary
depending on the aspect ratio or
mode selection of the TV.
*Operation has been confirmed with recommended discs
and tested disc, but some other discs may not be
usable.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Choosing a disc (Continued)
Structure of disc contents
On handling discs
Normally, DVD video discs are divided into titles, and the
titles are subdivided into chapters.
Do not touch the playback side of the disc.
VIDEO CDs/audio CDs are divided into tracks.
DVD video disc
Title 1
Title 2
Yes
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Playback side
Do not stick paper or tape to discs.
VIDEO CD / audio CD
Track 2 Track 3 Track 4
Track 1
Track 5
No
Title:
Divided contents of a DVD video disc.
Roughly corresponds to a story title in short
stories.
On cleaning discs
Chapter: Divided contents of a title. This corresponds
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc clean.
to a chapter in a story.
Divided contents of a VIDEO CD or an audio
CD.
Track:
Each title, chapter, or track is assigned a number, which
is called “title number”, “chapter number”, or “track
number” respectively.
Yes
No
Some discs may not have these numbers.
When you record on the HDD or a DVD-RAM disc, one
recording will always equal one title.You can divide a title
into several chapters by marking borders in it to facilitate
scene search.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS ...................................................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS ............................................................................... 4
Precautions........................................................................................................................... 6
Installation procedure........................................................................................................ 10
About this product ............................................................................................................. 11
Choosing a disc ................................................................................................................. 12
Preparation of the remote control .................................................................................... 18
Connections
Connecting an antenna and TV......................................................................................... 20
Connecting to cable TV signal .......................................................................................... 22
Connecting to a satellite system ...................................................................................... 24
Connecting the G-LINK® cable .......................................................................................... 25
Connecting to a TV equipped with component video inputs......................................... 26
Connecting to an audio system ........................................................................................ 27
Basic setup
Starting up the recorder .................................................................................................... 30
A: TV Guide On Screen® setup ......................................................................................... 32
Setting up TV Guide On Screen® .......................................................................... 33
B: Language setting........................................................................................................... 39
C: Satellite set top box setting.......................................................................................... 40
D: Output sound setting .................................................................................................... 44
E: TV shape setting ............................................................................................................ 46
F: Remote control settings................................................................................................ 48
Operating a TV with the remote control of this recorder ........................................ 48
Operating the second and third TOSHIBA HDD/DVD video recorders with the
remote control of this recorder .............................................................................. 50
Limited United States Warranty ........................................................................................ 52
CANADIAN WARRANTY INFORMATION .......................................................................... 54
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Preparation of the remote control
Caution
• Never throw batteries into a fire.
Open the cover.
1
Notes
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Do not mix different battery types or combine used
batteries with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not be using the
remote control for a long time, remove the batteries to
prevent battery acid from leaking into the battery
compartment.
Insert batteries (AAA size).
2
Operating with the remote control
Point the remote control at the remote sensor and
press the buttons.
Make sure to match the + and – on the
batteries to the marks inside the battery
compartment.
30°
30°
Within about 7 m (23 ft)
Close the cover.
3
Distance: About 7 m (23 ft) from the front of the
remote sensor
Angle
: About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the recorder to a
strong light source such as direct sunlight or other
illumination. If you do so, you may not be able to
operate the recorder via the remote control.
Notes
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote control.
• Do not disassemble the remote control.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection procedure
1
“Connecting an antenna
and TV” (
page 20)
Connections
Connect your recorder to your TV or stereo system.
Connecting an antenna and TV
Connecting to cable TV signal
Connecting to a satellite system
Connecting the G-LINK® cable
“Connecting an antenna
2
3
and TV” (
page 20)
Connecting to a TV equipped
with component video inputs
Connecting to an audio system
“Connecting to a TV
equipped with
audio/video inputs”
(
page 21)
4
“Connecting to an audio
system” (
page 27)
AV amplifier
When you connect a TV equipped with audio/
video inputs
Perform steps 1, 2 and 3.
When you connect an audio system
Perform steps 1, 2, 3 and 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting an antenna and TV
Connect your TV and the antenna to this recorder for recording and to view broadcast signals on the TV.
Disconnect the antenna cable from your TV, and connect it to the RF IN
(FROM ANT.) terminal on the recorder.
1
2
Using the supplied coaxial cable of this recorder, connect the RF OUT (TO
TV) terminal to the TV.
VHF/UHF antenna
Antenna cable (not supplied)
To RF IN (FROM ANT.)
1
TV
To RF OUT (TO TV)
2
Coaxial cable (supplied)
To antenna input
2
Antenna
splitter
(not supplied)
e.g.
Types of an antenna terminal
may vary depending on the TV.
Check the type on your TV, and
VHF/UHF
connect properly using either
method as shown.
For connecting to a cable box or a satellite system, see
page 22 to 25.
Note
• This connection ensures broadcast signals to be passed through to your TV. Unlike a VCR, you cannot assign channel 3 or 4
to playback from this recorder. The antenna input only passes through the broadcast signals to your TV.
Therefore to playback video from this recorder you must connect it to a video input on your TV. (See the next page.)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to a TV equiped with audio/video inputs.
Connect as below for watching received channels or recorded contents. Watching via the RF OUT terminal
is not available.
3
4
(yellow)
(red)
(white)
To OUTPUT
(S-VIDEO)
To OUTPUT
(R/L)
To OUTPUT
(VIDEO)
S-Video cable (not supplied)
If the TV has an S-video input, connect the recorder
with an S-video cable. When using an S-video
cable, do not connect the yellow video cable.
Video/audio cable (supplied)
TV or monitor with
To S-video input
audio/video inputs
To video inputs (yellow)
(white)
To audio input
(red)
Connect the power cord of the recorder to a wall outlet.
Make sure that the powered recorder lights the ON/STANDBY indicator on the front panel.
To wall outlet
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the recorder to your TV, be sure to turn off the power and unplug both units from the wall outlet before any
connections.
• If your television set has one audio input, connect the left and right audio outputs of the recorder to a Y cable adapter (not
supplied) and then connect to your TV.
• Connect the recorder directly to your TV. If you connect the recorder to a VCR, TV/VCR combination, video selector or AV
amplifier, the playback picture may be distorted due to copy protection.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to cable TV signal
Choose one of the setup options below to connect the recorder to your cable signal.
Connect the recorder to the TV using the audio/video cable.
This set-up will allow you to:
– record an unscrambled channel.
– record an unscrambled channel while watching
another (only when you connect a cable-compatible
TV).
You will need to:
• on your TV select a desired channel to watch while
recording a different channel using the recorder.
Incoming cable
This set-up will allow you to:
– record an unscrambled channel.
– record an unscrambled channel while watching
another (scrambled or unscrambled).
You will need to:
• set TV channel to the output channel of the cable box.
• to record an unscrambled channel while watching a
scrambled channel, select a desired cable channel via
the cable box.
Cable box
3CH
4CH
Incoming cable
OUT
IN
This set-up will allow you to:
– record any channels through the cable box.
You will need to:
• select a desired cable channel via the cable box.
• while the recorder is turned off, set TV channel to the
output channel of the cable box.
To download program listings the TV Guide On Screen®
system needs to be able to change channels on your
cable box when the recorder is not in use. Please
Cable box
connect the supplied G-LINK® cable to the G-LINK jack
of the recorder. After you connect the G-LINK® cable you
will be able to control your cable box using the recorder’s
3CH
4CH
OUT
IN
remote control.
page 25
Incoming cable
22
Download from Www.Somanuals.com. All Manuals Search And Download.
This set-up will allow you to:
– watch or record a channel through the cable box via
the INPUT1 (VIDEO/L/R) jacks.
To download program listings the TV Guide On Screen®
system needs to be able to change channels on your
cable box when the recorder is not in use. Please
connect the supplied G-LINK® cable to the G-LINK jack
of the recorder. After you connect the G-LINK® cable you
will be able to control your cable box using the recorder’s
remote control.
page 25
IN
Cable box
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to a satellite system
Choose one of the following according to your type of satellite receiver.
When the satellite receiver does not have audio/
video outputs
1 Connect a satellite antenna to the satellite receiver.
2 Connect the RF IN (FROM ANT.) terminal on the
recorder and the RF OUT terminal of the satellite
receiver.
3 Connect the RF OUT (TO TV) terminal on the recorder
and the antenna input connector of the TV.
Satellite receiver
3CH
4CH
IN
OUT
Satellite antenna
When the satellite system has audio/video outputs
Satellite antenna
1 Connect a satellite antenna to the satellite system.
2 Connect the INPUT1 or INPUT3 (VIDEO/L/R) jacks on
the recorder and the audio/video output jacks of the
satellite system.
Satellite
receiver
Audio outputs
Video output
3 Connect the OUTPUT (VIDEO/L/R) jacks on the
recorder and the audio/video input jacks of the TV.
4 Connect the RF OUT (TO TV) terminal on the recorder
and the antenna input connector of the TV.
Note
• If you use the DSS set top box control function (
page 40), connect your satellite set top box to the INPUT3 jacks.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
®
Connecting the G-LINK cable
To download program listings the TV Guide On Screen® system needs to be able to change channels on
your cable box when the recorder is not in use. Please connect the supplied G-LINK® cable to the
G-LINK jack of the recorder. After you connect the G-LINK® cable you will be able to control your cable
box using the recorder’s remote control. To connect the G-LINK® cable follow the instructions below.
Connect the plug of the supplied G-LINK® cable to the G-LINK jack on the
recorder.
1
2
Place the transmitter near the set top box connected to the recorder.
Cable box
(Keep the power on to receive
commands from the recorder.)
1
Transmitter
2
Secure the G-LINK® wand
underneath the cable box so that
the wand’s IR lens faces the front
of cable box.
Ensure the G-LINK® wand is at a
distance of about one inch from
the cable box IR sensor. If you
cannot control your cable box, try
to adjust the distance or put the
G-LINK® wand at another place.
After connecting, make the necessary settings (
page 32).
When you use the recorder for the first time, also make the settings.
Notes
• Do not connect an accessory other than the supplied G-LINK® cable to the G-LINK jack.
• Do not cover the transmitter.
• The TV Guide On Screen® interactive program guide supports cable-ready and cable box as well as over-the-air broadcast. It
does not provide listings for satellite services. TV Guide program data and schedules are updated daily through your antenna
or cable system once you have completed the TV Guide On Screen® setup.
• Refer to the owner’s manual of the connected set top box as well.
• Power off the recorder overnight or when not in use to allow the TV Guide On Screen® system to receive and update its
listings. If a cable box is connected to this recorder, leave the cable box turned on at all times.
Program listings should start displaying within 24 hours after setting up the TV Guide On Screen® system (
page 32).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to a TV equipped with component video inputs
If your TV has component video inputs, you can obtain pictures in better quality.
To PB VIDEO OUT
To Y VIDEO OUT
To PR VIDEO OUT
Video cable
(not supplied)
TV or monitor equipped with
component video (INTERLACED/
PROGRESSIVE) inputs
Only video signals are output
from the COMPONENT OUTPUT
jacks.
(Audio signals are not output.)
To obtain the sound, connect an
audio system to the audio output
terminals.
To PR video input
To PB video input
To Y video input
To switch the output signal (Progressive/Interlaced)
Component video outputs/inputs
Press PROGRESSIVE button to change the
Some TVs or monitors are equipped with component
video inputs. Connecting to these inputs allows you to
enjoy higher quality picture playback.
PROGRESSIVE
video output signals (progressive and
interlace) from COMPONENT OUTPUT jacks.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex.Y, R-Y, R-B or
Y, CB, CR
)
In some TVs or monitors, the color levels of the
playback picture may be reduced slightly or the tint
may change. In such a case, adjust the TV or monitor
for optimum performance.
• Make the following setting.
On-screen display
Page
Select
“Audio out select”
“Analog 2ch”
page 39
Notes
• Refer to the owner’s manual for the TV to be connected to this recorder for more information concerning an audio system.
• If you place the recorder near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the recorder
away from the tuner and radio.
• The output sound of the recorder has a wide dynamic range. Be sure to adjust the audio amplifier’s volume to a moderate
listening level. Otherwise, the speakers and your hearing may be damaged by sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the recorder’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• Consumers should note that not all high definition television sets are fully compatible with this product and may cause
artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user
switch the connection to the “Standard Definition” output. If there are questions regarding our TV set compatibility with this
model 525p DVD player, please contact our Customer Service Center.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting to an audio system
You can enjoy multichannel surround-sound such as 5.1 channel by connecting to an amplifier
compatible with Dolby® Digital and DTS® sound.
• For connection to your TV, see
pages 20 to 21, 26.
• For details of output sound, see
page 162 in “OPERATIONS GUIDE”.
Caution
• When you are connecting (via the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack) an AV decoder that does not have
Dolby Digital, Digital Theater Systems (DTS) or MPEG2 decoding function, be sure to set “Audio out select” to “PCM”
from the on-screen displays (
speakers.
page 39). Otherwise, high volume sound may damage your hearing as well as the
• When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog
stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the analog audio
out (L/R) jacks of the recorder are connected to an amplification system. To enjoy DTS Digital Surround® playback, an
external 5.1 channel DTS Digital Surround® decoder system must be connected to the DIGITAL AUDIO OUTPUT
BITSTREAM/PCM jack of the recorder.
Amplifier
To OPTICAL type
digital audio input
To DIGITAL AUDIO
OUTPUT
BITSTREAM/PCM
Optical digital cable (not supplied)
• Make the setting on
page 39, “Audio out select”.
Manufactured under license from Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
Notes
• DO NOT connect the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack of the recorder to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the DIGITAL
AUDIO OUTPUT BITSTREAM/PCM jack of the recorder.
• Connect the DIGITAL AUDIO OUTPUT BITSTREAM/PCM jack of the recorder to the “OPTICAL” input of a Receiver or
Processor.
• Refer to the owner’s manual for the TV to be connected to this recorder for more information concerning connecting an audio
system.
• The output sound of the recorder has a wide dynamic range. Be sure to adjust the audio amplifier’s volume to a moderate
listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the recorder’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
Read this chapter for necessary settings to get started.
When you use this recorder for the first time, be sure to
perform A to C in this order.
Proceed to D if necessary.
Starting up the recorder
A:TV Guide On Screen® setup
Setting up TV Guide On
Screen®
B: Language setting
C: Satellite set top box setting
D: Output sound setting
E: TV shape setting
F: Remote control settings
Operating a TV with the
remote control of
this recorder
Operating the second and
third TOSHIBA HDD/DVD
video recorders with the
remote control of this
recorder
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
Starting up the recorder
While the icon is flashing, the recorder is checking
the status and reading data of the HDD and the
DVD drive for startup. If the DVD drive does not
contain a disc, the recorder consumes less time to
startup, because it does not need to read data
from the DVD drive.
While the “Loading” icon is flashing, the recorder
cannot respond to any operations of buttons other
than CH/Page and INPUT SELECT. Operate all other
functions after the icon has disappeared.
After all the necessary connections,
• Turn on the equipment connected to the
recorder.
• Select the corresponding video input on
your television.
Perform these selections whenever you operate
the recorder.
Notes
• When the recorder is turned on for the first time, the
Welcome screen will be displayed after the “Loading” icon
has disappeared. See “A: TV Guide On Screen setup”
(
page 32).
Turning the power on
• While displaying “WAIT” on the front panel, do not operate
the recorder or unplug the power cord. Otherwise, this may
result in malfunction of the recorder.
Press ON/STANDBY button from the remote control or
on the front panel of the recorder.
ON/STANDBY button/
ON/STANDBY indicator
Turning the power off
Press ON/STANDBY button from the remote control or
on the front panel of the recorder.
The “Unloading” icon appears on the right corner of
the top of the screen, and the ON/STANDBY indicator
turns red. Then the power turns off.
Note
ON/STANDBY button
• If the recorder freezes for about 15 minutes and will not
respond to any buttons, holding down ON/STANDBY
button on the front panel for about 10 seconds can force
the recorder to turn off. However, this is an emergency
measure, which contains a risk of damage to data or discs.
Avoid casual use of this measure. If you try this while the
recorder is operating properly, especially while the
“Loading” or “Unloading” icon is flashing, it may result in re-
initialization of the HDD.
When the power turns on, ON/STANDBY indicator
changes color from red (standby mode) to green
(operation).
Startup/finishing (closing) icons
These icons are displayed on the right corner on the
top of the screen. While they are flashing, the recorder
is operating as follows:
After a few seconds, a startup screen appears.
The following icon will appear on the top right corner
of the screen. The icon will continue flashing
momentarily.
Startup, reading a disc, finishing recording
Loading
e.g.
Loading
Unloading a disc, finishing the recorder’s
operation
Un
loading
Opening a disc tray
Open
Close
Closing a disc tray
30
Download from Www.Somanuals.com. All Manuals Search And Download.
If a message appears
The recorder may display a message. Each message
varies according to operational status.
To respond, follow the examples below.
Message
e.g.
message
OK
Set
e.g.
Select either response (by
highlighting in green) using
/
buttons, then press
message
ENTER button.
The message disappears.
Y
e
s
No
2 selections
e.g.
Read the message, then press
ENTER button.
The message disappears.
message
OK
1 selection
e.g.
The message disappears
automatically in a few seconds.
message
No selection
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
®
A: TV Guide On Screen setup
This step sets the recorder’s clock and tuner to record broadcasting TV programs.
Once you complete this process there is generally no need to reset the clock. (However, if there are
discrepancies in the recorder’s time display or changes made to receivable TV stations, you should
make this setting again.)
To set up the recorder for the first time see the TV Guide
On Screen® setup instructions on
page 33.
Press TV Guide.
1
TV Guide
Start
Press
/
/
to select “SETUP”.
2
3
4
ENTER
Press
to select “Change system
settings”, then press ENTER.
ENTER
Press
/
to select “No, repeat setup
process”, then press ENTER.
ENTER
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up TV Guide On Screen®
Setup selection
Reminder
1
2
Your DVD Recorder is equipped with the TV Guide On Screen™
Interactive Program Guide, which provides program listings,
one-touch recording, and more –– all subscription FREE!
Please follow the on-screen setup instructions to enable your TV
Guide On Screen system now. Or, press the GUIDE Key on your DVD
Recorder remote at any time.
ENTER
What would you like to do now?
Set up TV Guide On Screen now
Remind me to set it up later
Don’t remind me again
Using your DVD Recorder remote, move up or down to highlight your answer. Press
Enter to choose.
Instructions are provided at the bottom for each screen.
Press
/
to select “Set up TV Guide On
Screen Now”, then press ENTER.
Country
STEP 1: Identifying Your Location
To supply your DVD Recorder with correct program listings, the TV Guide On
Screen system needs to know your DVD Recorder’s location.
ENTER
Which country is your DVD Recorder located in?
USA
Canada
Using your DVD Recorder remote, move up or down to highlight your answer. Press
Enter to choose.
Press
/
to select, then press ENTER.
(Continued)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
A: TV Guide On Screen® setup (Continued)
ZIP or postal code
3
STEP 1: Identifying Your Location
To supply your DVD Recorder with the correct program listings, the TV Guide On
Screen system needs to know the town or city where your DVD Recorder is
installed.
1
4
7
0
2
5
8
3
6
9
Please enter the 5-digit ZIP code where your DVD Recorder is
located:
=
=
=
=
=
ENTER
Use one of the options below to enter your ZIP
or Postal Code, then press ENTER:
• Number buttons
•
/
to select a number, then
/
to move to another field.
Cable service
4
5
STEP 2: Configuring for Cable
To supply your DVD Recorder with correct program listings, the TV Guide On
Screen system needs to know if your DVD Recorder receives its signal from a cable
service.
ENTER
Do you have cable service connected to this DVD recorder?
Yes
No
Press
/
to select, then press ENTER.
If the answer is “No”, you will go to step 12.
Cable connection
STEP 2: Configuring for Cable
You have indicated that you have cable service. Now the TV Guide On Screen
system needs some additional information.
ENTER
Is a cable box connected to this DVD Recorder?
Yes
No
Press
/
to select, then press ENTER.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable input
6
STEP 2: Configuring for Cable
Your DVD Recorder has more than one input jack. To operate properly with your
cable box, the TV Guide On Screen system needs to know which one your cable
box is plugged into. You may have to look at the back of your DVD Recorder
if you are unsure, as an incorrect selection will result in a blue or snowy screen while
watching TV.
ENTER
Please indicate which DVD Recorder input the cable box is
plugged into.
TUNER
Line 1
Press
/
to select, then press ENTER.
If you select “TUNER”, you will go to step 7.
If you select “Line 1”, you will go to step 8.
Tuning channel for the cable box
7
8
STEP 2: Configuring for Cable
To operate properly with your cable box, the TV Guide On Screen system needs to
know the channel your DVD Recorder is on when using the cable box. The most
commonly used output channel is 03. Please consult your cable box provider if you are
unsure, as an incorrect selection will result in a blue or snowy screen while
watching TV.
ENTER
What is your DVD Recorder tuned to when using the cable box?
Ch 2
Ch 3
Ch 4
Press
/
to select, then press ENTER.
Read the instructions and observe the
diagram. Confirm that the G-LINK® cable and
its wand is properly installed. ( page 25)
If OK, press ENTER.
ENTER
(Continued)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
A: TV Guide On Screen® setup (Continued)
Cable box brand name
9
STEP 2: Configuring for Cable
Selecting the correct cable box brand from the list is needed to automatically
receive program listings. If you do not know the cable box brand, please consult
your cable provider.
ENTER
What brand of cable box is connected to this DVD Recorder?
Not listed
Archer
Cable Cinema
Cabletenna
Press
/
to view and select more brands,
then press ENTER.
Cable box preparation
10
11
STEP 2: Configuring for Cable
The TV Guide On Screen will conduct a series of tests to find the
correct code to control your cable box.
ENTER
Follow steps A and B below
A: Please tune your cable box to channel 02
B: Make sure to leave your cable box turned ON
Follow the instructions, then press ENTER.
Cable box code testing
STEP 2: Configuring for Cable
Cable testing in progress... please do not press any keys on
any remote control.
Now testing code 036 (Toshiba)...
Press Enter to continue.
When testing is done, the following screen automatically appears.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2: Configuring for Cable
The TV Guide On Screen system needs to locate the correct code for yourcable box
brand in order to work properly.
ENTER
Is your cable box now tuned to channel 09?
Yes
No
Test the code again
Press
/
to select, then press ENTER.
If your answer is “Yes”, and:
• if you selected “TUNER” at step 6,
you will go to step 13.
• if you selected “Line 1” at step 6,
you will go to step 12.
Antenna connection
12
13
STEP 3: Configuring for Antenna
To supply your DVD Recorder with correct program listings, the TV Guide On Screen
system needs to know if you have attached an antenna to your DVD Recorder to
receive over-the-air stations.
ENTER
Do you have an antenna connected to your DVD Recorder?
Yes
No
Press
/
to select, then press ENTER.
Confirmation
STEP 4: Confirming Your Settings
You have entered the following TV Guide On Screen system settings. If any setting
is marked INCOMPLETE, you will not be able to use the feature until you complete
that portion of TV Guide On Screen system setup.
ZIP code - 46001 (USA)
Cable Box on input “TUNER” Ch. 3
Cable Box selected: code 036 (Toshiba)
ENTER
Are the above settings correct?
Yes, end setup
No, repeat setup process
Press
/
to select, then press ENTER.
(Continued)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
A: TV Guide On Screen® setup (Continued)
Confirmation
14
15
Congratulations!
You have completed the setup of your TV Guide On Screen system.Up-to-date
listings will begin loading over the next 24 hours when your DVD Recorder is
powered off.
ENTER
It may take more than one day for all eight days of listings to update. During this
period feel free to use your DVD Recorder. The guide will automatically receive
updates during the period when your DVD Recorder is turned off.
If you have changed the location or cable configuration settings, you will receive
any changes to your local channel lineup within 24 hours.
You have successfully completed the setup!
Press ENTER.
Information
Helpful information
1. To receive your channel lineup and program listings, leave your cable box ON.
Your DVD Recorder should be turned OFF overnight.
2. To view program listings, press the GUIDE key on your DVD Recorder remote.
ENTER
3. You must redo TV Guide On Screen system setup if you:
Move your DVD Recorder to a new ZIP or postal code
Cancel cable service or change cable boxes
To enter the TV Guide On Screen system setup, press the GUIDE key, then go to the
Menu Bar and highlight Setup.
Read the information and press ENTER.
Notes
• When the clock data cannot be downloaded from the TV Guide On Screen® system, set the clock manually. (
“OPERATIONS GUIDE”)
page 157, in
• It may take about 24 hours for the TV Guide On Screen® system to be fully available after the setup is finished.
• TV Guide On Screen® system is not compatible with the DSS set top box control function (
page 40). If you select “Yes” at
page 34) and complete the setup, the recorder sets itself to TV Guide On Screen® system and disables the
page 40.
step 5 (
setting on
“A: TV Guide On Screen® setup” is complete. Go to “B: Language setting”. (
page 39)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
B: Language setting
Select a preferred language for on-screen displays.
Press SETUP.
1
2
The setup menu appears.
SETUP
Press
/
to select “Initial settings”, then
press ENTER.
e.g.
Initial settings
English
ENTER
Language
Time & Date setting
Guide and Clock reset
Set Top Box setting
SETUP
Exit
Select
Return
Set
Refer to the guide on the bottom on each GUI
for further programming related information.
Press
ENTER.
/
to select “Language”, then press
3
4
e.g.
Initial settings
English
Time & Date setting
Guide and Clock reset
Set Top Box setting
ENTER
Language
English
French
Start
Press
ENTER.
/
to select a language, then press
English: To view on-screen displays in English.
French: To view on-screen displays in French.
ENTER
“B: Language setting” is complete. Go to “C: Satellite set top box setting” (
page 40).
Note
• This setting is not available for TV Guide On Screen® displays.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
C: Satellite set top box setting
Set your recorder to control channels of a connected satellite set top box. (DSS set top box control
function)
This setting is only for users who do not or can not
STEP 2: Configuring for Cable
control channels of a connected cable box by
You have indicated that you have cable service. Now the TV Guide On Screen
system needs some additional information.
means of TV Guide On Screen® system.
If you selected “Yes” at step 5 on
page 34,
you do not need to do this setting. Skip to “D:
Is a cable box connected to this DVD Recorder?
Output sound setting” (
page 44).
Yes
No
Important
• Be sure to connect your satellite set top box to the INPUT3 jacks of the recorder.
• Make the G-LINK® cable connection (
page 25) between your satellite set top box and the recorder.
Press SETUP to display the setup menu.
1
2
When it is already displayed, press button.
SETUP
Press
/
to select “Initial settings”, then
press ENTER.
e.g.
ENTER
Initial settings
English
Language
Time & Date setting
Guide and Clock reset
Set Top Box setting
Press
/
to select “Set Top Box setting”,
then press ENTER.
3
e.g.
Start
ENTER
Set Top Box setting
Not used
DBS
Input
Line3
Off
0 0 0
On
IR control
Brand type
ENTER code
Channel digit
3 digits
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ADJUST (or / ) to set “DBS” to “Not
used” or “Use”.
4
Not used:
When a satellite set top box is not connected to the
INPUT3 jacks of the recorder.
Skip to step 8.
R
Use:
When a satellite set top box is connected to the INPUT3
jacks of the recorder.
Press , then press ADJUST (or / ) to set
“IR control” to “On” or “Off”.
5
Off: Channels of the satellite set top box are selected
by its own selector.
Skip to step 8.
ENTER
On: The recorder can change channels of the satellite
set top box.
R
Press , then press the number buttons to
enter the 3 digits of a brand code of your
satellite set top box obtained from the list
6
(
page 43).
e.g. If you connect a TOSHIBA satellite set top box:
0
9
0
ENTER
1
4
7
0
2
5
8
3
6
9
Press , then press ADJUST (or / ) to set
“ENTER code” to “On” or “Off”.
7
Confirm whether the connected satellite set top box
requires ENTER input after digits in channel selection or
not.
ENTER
On: If ENTER input is required.
Off: If ENTER input is not required.
R
(Continued)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
C: Satellite set top box setting (Continued)
Press ENTER.
8
“Initial settings” menu returns.
To exit the setting menu, press SETUP button.
ENTER
If you have set “IR control” to “On” at step 5 (
page
41), turn on your satellite set top box and confirm its
channels are selected by the number buttons or
CH/Page buttons of the recorder’s remote control. If not,
shift the G-LINK® wand of the G-LINK® cable or try
another brand code.
“C: Satellite set top box setting” is complete. Go to “D: Output sound setting” (
page 44).
Notes
• This setting will be reset to default if you redo the TV Guide On Screen® setup and select “Yes” at the cable selection (step 5,
page 34).
• The recorder can control satellite set top box of 3 digit channel selection only. If the channel control does not work properly,
set “IR control” to “Off” at step 5 on
page 41.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite set top box brand code
Brands
Codes
DirecTV
Drake
106
093
Echostar
Hitachi
092 100
091 099 102 105
091 099 102 105
094 095
094 095
096
091 099 102 105
092 100
097 103
097 103
097 103
098
Hughes
Magnavox
Optimus
Panasonic
Philips
Primestar
ProScan
RCA
Samsung
Sony
Toshiba
Uniden
Zenith
090
094 095
101
Note
• Some models of satellite set top box may not be controlled
with this recorder.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
D: Output sound setting
Select the output sound setting corresponding to the connected TV or audio system.
Press SETUP to display the setup menu.
1
When it is already displayed, press button.
SETUP
Press
/
to select “Picture/Audio settings”,
then press ENTER.
2
3
e.g.
Picture/Audio settings
ENTER
Pause / Still
Auto
Standard
Normal
Output Black level
Custom picture select
Custom picture setting
Progressive conversion
Play DNR
Audio out select
Virtual surround
SAP
Auto
Bitstream
Off
Off
Press
/
to select “Audio out select”, then
press ENTER.
e.g.
ENTER
Picture/Audio settings
Auto
Pause / Still
Bitstream
Analog 2ch
PCM
Output Black level
Custom picture select
Custom picture setting
Progressive conversion
Play DNR
Standard
Normal
Auto
Audio out select
Virtual surround
SAP
Bitstream
Off
Off
Start
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
/
to select the output sound format.
4
Bitstream:
Select when connected to an amplifier equipped with a
Dolby Digital, DTS, MPEG1 and MPEG2 decoder. (
page 27)
ENTER
OPTICAL
Amplifier
The recorder outputs digital audio signals in the
bitstream format when you play a DVD video disc
recorded on the Dolby Digital, DTS, MPEG1 and
MPEG2 recording system.
Analog 2ch:
Select when connected to a TV or audio system via the
analog audio jacks. (
pages 21, 26)
AUDIO
INPUT
TV
L
R
PCM:
Select when connected to a 2 channel digital stereo
system. (
page 27)
OPTICAL
Amplifier
The recorder outputs sounds in the PCM 2ch format
when you play a disc recorded on the Dolby Digital,
MPEG1 and MPEG2 recording system.
Once the proper setting is selected, press
ENTER.
5
The submenu disappears.
To exit the setting menu, press SETUP button.
ENTER
“D: Output sound setting” is complete. Go to “E: TV shape setting”. (
page 46)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
E: TV shape setting
Select the picture shape according to the aspect ratio of your TV.
Press SETUP to display the setup menu.
1
2
When it is already displayed, press button.
(To return to the previous menu)
SETUP
Press
/
to select “Display settings”, then
press ENTER.
e.g.
ENTER
Display settings
4:3LB
TV shape
On screen display
Transparency
Startup screen
Screen protector
Background
On
25%
On
On
Blue
TV
Closed caption
Press
ENTER.
/
to select “TV shape”, then press
3
e.g.
ENTER
Display settings
4:3LB
TV shape
4:3LB
4:3 normal
16:9 wide
16:9 shrink
On screen display
Transparency
Startup screen
Screen protector
Background
On
25%
On
On
Blue
TV
Closed caption
Start
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
/
to select the picture shape.
4
5
4:3LB:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
ENTER
4:3 normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill your
TV screen. Either or both of the
picture’s sides are cut off.
16:9 wide:
Select when a 16:9 wide TV is
connected.
16:9 shrink:
Select when a 16:9 wide TV is
connected.
When a 4:3 aspect ratio image has
been elongated to 16:9 wide picture
size, use this setting.
Masking bars to the right and left
appears.
When the proper setting is selected, press
ENTER.
The submenu disappears.
To exit the setting menu, press SETUP button.
ENTER
Notes
• Actual picture shape may depend on signal types of broadcasts or input sources, or settings on the connected TV. Refer to
the owner’s manual of your TV.
• When a DVD video disc has a particular available picture shape, the contents may not be compatible with other picture
shapes.
“E: TV shape setting” is complete. Go to “F: Remote control settings”. (
page 48)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
F: Remote control settings
Take this step according to your preference and usage.
Operating a TV with the remote control of this recorder
The remote control of this recorder has a function to operate a TV.
Preparation: Please find the brand code on the next page for the TV you wish to control.
INSTANT REPLAY INSTANT SKIP
EASY
While holding TV CODE, press the number
NAVI
buttons to enter a corresponding brand code
(see the next page) of your TV.
Menu
TV Guide
1
Info
CONTENT MENU
e.g. To enter 0071
TV CODE
TV CODE
0
0
7
1
Hold down.
ENTER
1
4
7
0
2
5
8
3
6
9
E
PAUSE
REC
STOP
PLAY
QUICK MENU
Release TV CODE.
Exit
2
The brand code is memorized.
Start
DVD
OP MENU
1
4
7
0
2
3
6
9
ENU
5
RETURN
8
T.SEARCH TV CODE
+
10
Operating your TV with the remote control
Point the remote control to your TV after you have entered the brand code. Operate your TV with the buttons below.
ON/STANDBY: To turn on and off the TV
VOLUME
CH
TV/VIDEO
CH
: To change the video input
: To select the TV channel
: To adjust the volume
ON/STANDBY
TV/VIDEO
VOLUME
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Brand code table
Brand name
Brand code
Brand name
Philco
Brand code
Toshiba
0001 0021 0071 0311 0411
0431 0831 0841 0851 1341
1611 1621 1681 1781 1951
2121 2461 2491
0081 0431
0051 0381 0471 0551 0621
0851 1561
0051 0391 0431 0531 0621
0851 1521 1561 2501
0051 0111 0121 0141 0151
0161 0201 0211 0351 0381
0431 0521 0561 0571 0621
0691 1241 1291 1371 1561
2481
0251 0401 0431 1151 2451
2481
0041 0051 0091 0181 0321
0371 0391 0591 0621 0711
0741 0881 1041 1471 1521
2481 2501
0051 0161 0271 0291 0361
0421 0501 0551 0621 0631
0661 0711
0051 0161 0271 0321 0361
0421 0461 0551 0631 0661
0711 2141 2351
0051 0161 0621 0651 2491
0711 0741 0801 1401 2281
0431 1521 2481
Philips
Bell & Howell
Citizen
Proton
Quasar
Radio Shack
Curtis Mathes
Emerson
Radio Shack/Realistic 0051 0161 0381 0391 0431
0541 0621 1431 1561 2501
RCA
0051 0221 0391 0501 0621
0661 0711 0871 0881 0911
0921 0941 1001 1041 1071
1091 1181 1211 1241 1301
1461 1491 1521 1531 2291
2481 2501
Fisher
GE
Realistic
Runco
Samsung
0431 1521
0011
1811 0051 0161 0501 0531
0621 0661 0851 0931 1021
1141 1431 1561 1591 1601
1771 1821 1831 1841 1851
1861 1931 2081 2101 2311
0051 0261 0401 0431 0791
0901 1151 2461
0001 0051 0151 0191 0251
0311 0331 0391 0401 0411
0431 0621 0661 1041 1081
1151 1481 1521 2461 2481
2501
2181 0051 0111 0161 0351
0541 0581 0611 0621 0731
0891 1101 1561 1721 1871
1881 1941 2341
1231 0441 1111 1511 2411
1891 1901 2061 2421 2431
2401
Goldstar
0051 0061 0161 0231 0451
0501 0621 0661 0771 0961
1431 1561 2481
Hallmark
Hitachi
0051 0621
2381 0031 0051 0161 0191
0301 0601 0621 0641 0671
0811 0821 0951 1011 1061
1241 1361 1651 1711 1731
1741 1751 1761 2041 2051
2131
Sanyo
Sears
Infinity
JBL
JVC
0631
0631
Sharp
Sony
0101 0161 0191 0241 0331
0511 0561 0601 0741 0991
1321 1421 2161 2171 2261
0001 0311 0391 0411 0431
0621 0631 1041 1171 1521
2491 2501
LXI
Magnavox
0051 0271 0291 0341 0361
0421 0551 0621 0631 0661
0971 0981 1131 2221 2351
0051 0481 0621 0631 0641
2491
0081 0431 0501 0621 2491
0051 0251 0261 0371 0501
0621 0661 0761
Soundesign
Sylvania
0051 0151 0381 0551 0621
2481
0051 0071 0271 0291 0341
0361 0421 0551 0621 0631
0661 0861 1441 2191 2201
1101
Marantz
Memorex
MGA
Tandy
Technics
Teknika
0741
0051 0081 0151 0161 0191
0341 0381 0471 0501 0551
0621 0851 1271 1401 1561
2481
Mitsubishi
0051 0251 0261 0281 0371
0491 0501 0621 0661 0761
2231 2241
MTC
NAD
Optonica
Panasonic
0051 0501 0621 0851
0001 0311 0411 0621 1061
0541 1101
2301 0631 0711 0741 1271
1351 1401 1501 1701 1791
1801 2111 2151
Wards
Zenith
0051 0081 0141 0151 0181
0211 0271 0321 0341 0361
0391 0421 0501 0541 0621
0631 0661 1051 1521 2491
2501
0011 0051 0081 0781 1281
1571 2091 2211 2251 2391
2361 2441
Notes
• TOSHIBA code is already set when you operate this recorder for the first time.
• Some brands have several codes. Try one by one until the remote control can operate your TV.
• Even after the recorder's remote control is programmed, it may not operate some or all of the features on your other device.
If this happens and you wish to use those features, you will need to use the device's original remote control.
• When replacing the batteries of the remote control, re-enter the brand code of your TV.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic setup
F: Remote control settings (Continued)
Operating the second and third TOSHIBA HDD/DVD video recorders with the remote control of this recorder
Switches the codes to operate the recorder.
If you use the second and third TOSHIBA HDD/DVD video recorders, set the different remote codes for each
recorder to avoid confusion in the response of the recorders.
Example: Setting this recorder’s remote control mode to DR 2, after another HDD/DVD recorder has been
set to DR 1.
(It is necessary to set the remote control mode on both the recorder and the remote control.)
Setting up the recorder
Press SETUP.
1
The setting menu appears.
SETUP
Press
/
to select “Operational settings”,
then press ENTER.
2
3
4
e.g.
Operational settings
ENTER
Operation beep
Completion beep
IR code
Instant skip interval
Instant replay interval
Title thumbnail point
HDD/RAM title play
Still group interval
Priority contents
Off
On
DR 1
30 sec.
10 sec.
35 sec.
Title resume
3 sec.
Photo
Press
/
to select “IR code”, then press
ENTER.
e.g.
Operational settings
ENTER
Operation beep
Completion beep
IR code
Instant skip interval
Instant replay interval
Title thumbnail point
HDD/RAM title play
Still group interval
Priority contents
Off
On
DR 1
30 sec.
10 sec.
35 sec.
Title resume
3 sec.
Photo
DR
DR
DR
1
2
3
Start
Press
/
to select “DR 2” (example), then
press ENTER.
The submenu disappears.
Press ENTER button and the IR code you selected is
activated. Operation may not be possible temporarily until
you set the corresponding mode of the remote control.
ENTER
Proceed to the next setting
.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the remote control
While pressing EASY NAVI, press 2.
5
The remote control mode is set to “DR 2”.
EASY
NAVI
2
Select the same mode that you have set to the recorder.
Mode setting
Recorder
Remote control
D R 1
D R 2
D R 3
When using with DR 1
mode
EASY
NAVI
+
+
+
1
2
3
D R 1
D R 2
D R 3
When using with DR 2
mode
EASY
NAVI
D R 1
D R 2
D R 3
EASY
NAVI
When using with DR 3
mode
Notes
• If the recorder’s mode and the remote control’s mode are different, the recorder’s mode (DR 1, DR 2 or DR 3) appears on the
display of the front panel.
• When the batteries of the remote control are replaced or when the time indicator of the front panel flashes, check the remote
control modes of both the recorder and the remote control, and re-program it if necessary.
Disabling the remote control for a temporary period
You can temporarily disable the reception of the remote control signals at the recorder, when the selection of DR 1,
DR 2 and DR 3 is not sufficient while you are using several Toshiba HDD/DVD video recorders.
Press HDD and DVD buttons on the recorder at the same time for three seconds or more.
The recorder display shows “DR - OFF”, indicating that the remote control is disabled.
To enable the remote control, perform the same step again. (The display shows “DR-1 , DR-2 or DR-3” depending on
your setting.)
Notes
• This function is not available in Standby mode.
• You cannot use this feature when the power is turned off, if you have set “Front Display” to “Off”.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited United States Warranty
Digital Audio Video (“DAV”) Product-Depot Repair Warranty
Toshiba America Consumer Products, L.L.C,. (“TACP”) makes the following limited warranties to original consumers in
the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY
PERSON RECEIVING THIS DAV PRODUCT AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO
NO OTHER PURCHASER OR TRANSFEREE.
DAV PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING,
WITHOUT LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION,
CANADA AND MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.
Limited Ninety (90) Day Warranty on Labor*
Your Responsibility
TACP warrants this DAV Product and its parts against
defects in materials or workmanship for a period of ninety
(90) days after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP’s
OPTION, REPAIR OR REPLACE A DEFECTIVE PART
WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU FOR PARTS OR LABOR.
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must retain your bill of sale or provide other
proof of purchase.
(2) All warranty servicing of this DAV Product must be
made by the Depot Warranty Repair Center
specified by the TACP Consumer Solutions Center.
Limited One (1) Year Warranty on Parts*
(3) The warranties from TACP are effective only if the
DAV Product is purchased and operated in the
Continental U.S.A. or Puerto Rico.
TACP further warrants the parts in this DAV Product
against defects in materials or workmanship for a period
of one (1) year after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP ’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART
WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU FOR THE PART, PROVIDED THAT IF
A DEFECTIVE PART IS REPAIRED OR REPLACED
AFTER NINETY (90) DAYS FROM THE DATE OF
ORIGINAL RETAIL PURCHASE, THE CONSUMER
SHALL PAY ALL LABOR CHARGES INVOLVED IN THE
REPAIR OR REPLACEMENT THEREOF.
(4) Labor service charges for set installation, setup,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to
any DAV Product or parts that have been lost or
discarded by you or to damage to DAV Product or
parts caused by fires, misuse, accident, Acts of God,
such as lightning or fluctuations in electric power,
improper installation, improper maintenance or use
in violation of instructions furnished by TACP; use or
malfunction through simultaneous use of this DAV
Product and connected equipment; or to units that
have been modified or had the serial number
*Rental Units
The warranty for DAV Product rental units begins on the
date of the first rental or thirty (30) days after the date of
shipment to the rental firm, whichever comes first.
*Commercial Units
DAV Products sold and used for commercial purposes
have a limited warranty for all parts and labor, which
warranty begins on the date of original retail purchase
and ends on the date that is ninety (90) days thereafter.
removed, altered, defaced, or rendered illegible.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating
this DAV Product.
Complete and mail the enclosed product registration card
or register your DAV Product on-line at
registering your DAV Product you will enable TACP to
bring you new products specifically designed to meet
your needs and help us to contact you in the unlikely
event a safety notification is required under the
Consumer Product Safety Act. Failure to complete and
return the product registration card does not diminish
your warranty rights.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Warranty Services
If, after following all of the operating instructions in this
manual and checking the section “Before calling service
personnel”, you find that service is needed:
(1) For instructions on how to obtain warranty service
for your DAV Product, contact TACP’s Consumer
Solution Center toll-free at 1-800-631-3811.
(2) You must include a copy of original bill of sale or
other proof of purchase along with the entire DAV
Product to the Depot Warranty Repair Center
specified by the TACP Consumer Solutions Center.
You are responsible for all inbound transportation
and insurance charges for the DAV Product to the
Depot Warranty Repair Center specified by the
TACP Consumer Solutions Center.
For additional information, visit TACP’s web site:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY
STATE OF THE U.S.A., INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE EXPRESSLY
LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE
LAW OF ANY STATE OF THE U.S.A. AS HEREBY
LIMITED, THE FOREGOING WARRANTY IS
EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, GUARANTEES, AGREEMENTS, AND
SIMILAR OBLIGATIONS OF TACP WITH RESPECT TO
THE REPAIR OR REPLACEMENT OF ANY PARTS. IN
NO EVENT SHALL TACP BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR
ERASURE OF RECORDED DATA CAUSED BY USE,
MISUSE OR INABILITY TO USE THIS DAV PRODUCT).
No person, agent, distributor, dealer or company is
authorized to change, modify or extend the terms of
these warranties in any manner whatsoever. The time
within which an action must be commenced to enforce
any obligation of TACP arising under the warranty or
under any statute, or law of the United States or of any
state thereof, is hereby limited to ninety (90) days from
the date you discovered or should have discovered, the
defect. This limitation does not apply to implied
warranties arising under state law.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE IN THE
U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, WHEN AN ACTION MAY BE
BROUGHT, OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE PROVISIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
Printed on 70% Recycled Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
|