Owner’s Manual
HDMI over Cat5 Extenders
and Extender/Splitters
Extender Kit Model: B126-1A1 and B126-1A1-WP
Local Unit Models: B126-002 and B126-004
Remote Unit Models: B126-1P0, B126-1P0-WP-1,
B126-1A0, B126-1A0-WP-1 and B126-110
Package Contents
Product Features
Mounting Instructions
Standard Extender Kit Installation
2
2
7
8
Extender Kit with Remote/Repeater Installation
Standard Extender/Splitter Installation
Extender/Splitter with Remote/Repeater Installation
Extender/Splitter Daisy-Chain Installation (B126-004 only)
Extender/Splitter Daisy-Chain with Remote/Repeater
Installation (B126-004 only)
10
13
16
20
23
Warranty & Warranty Registration
27
1111 W. 35th Street, Chicago, IL 60609 USA
Copyright © 2011 Tripp Lite. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
1
10/24/2011 10:01:17 AM
Product Features
B126-1A1
• HDMI over Cat5 Active Extender Kit (Box-style)
• Extends a 1080i (60Hz) signal up to 200 ft. from the source, or a
1080p (60Hz) signal up to 150 ft. from the source
• Features an additional HDMI port on the local transmitter unit for the
connection of local monitor
• Remote receiver unit features a built-in Equalization control for video
image adjustment
• Includes mounting hardware that allows both the local transmitter
and remote receiver units to be wallmounted, rackmounted or pole
mounted
B126-1A1-WP
• HDMI over Cat5 Active Extender Wallplate Kit
• Extends a 1080i (60Hz) signal up to 200 ft. from the source, or a
1080p (60Hz) signal up to 150 ft. from the source
• Remote receiver unit features a built-in Equalization control for video
image adjustment
• RJ45-style wallplates allow for the use of standard Cat5e/6 patch
cables; 110 punchdown connection not required
B126-002
• 2-Port HDMI over Cat5 Extender/Splitter Local Transmitter Unit
(Box-style)
• Splits an HDMI signal into 2
• Works with remote/repeater and receiver units to extend an HDMI
signal past the 16 ft. (5 m) distance limitation
• Includes mounting hardware that allows unit to be wallmounted,
rackmounted or pole mounted
3
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
3
10/24/2011 10:01:17 AM
Product Features
B126-004
• 4-Port HDMI over Cat5 Extender/Splitter Local Transmitter Unit
(Box-style)
• Splits an HDMI signal into 4
• Features an additional HDMI port, which can be used to connect a
local monitor or to daisy-chain additional B126-004 units.
Up to 3 B126-004 units can be daisy-chained together to increase
the number of connected monitors.
• Works with remote/repeater and receiver units to extend an HDMI
signal past the 16 ft. (5 m) distance limitation
• Includes mounting hardware that allows unit to be wallmounted,
rackmounted or pole mounted.
• Up to 3 B126-004 units can be mounted in a B132-004-RB 1U
rackmount bracket
B126-1A0
• HDMI over Cat5 Active Extender Remote Receiver Unit (Box-style)
• Works with B126-002 and B126-004 extender/splitters to extend
a 1080i (60Hz) signal up to 200 ft. from the source, or a 1080p
(60Hz) signal up to 150 ft. from the source
• Features a built-in Equalization control for video image adjustment
• Includes mounting hardware that allows the unit to be wallmounted,
rackmounted or pole mounted
4
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
4
10/24/2011 10:01:17 AM
Product Features
B126-1A0-WP-1
• HDMI over Cat5 Active Extender Wallplate
• Works with B126-002 and B126-004 extender/splitters to extend
a 1080i (60Hz) signal up to 200 ft. from the source, or a 1080p
(60Hz) signal up to 150 ft. from the source
• Features a built-in Equalization control for video image adjustment
• RJ45-style wallplate allows for the use of standard Cat5e/6 patch
cables; 110 punchdown connection not required
B126-1P0
• HDMI over Cat5 Passive Extender Remote Receiver Unit (Box-style)
• Works with B126-002 and B126-004 extender/splitters to extend
a 1080i (60Hz) signal up to 100 ft. from the source, or a 1080p
(60Hz) signal up to 50 ft. from the source
• Features a built-in HDMI cable; a separate HDMI cable is not required
• No external power required
B126-1P0-WP-1
• HDMI over Cat5 Passive Extender Wallplate
• Works with B126-002 and B126-004 extender/splitters to extend
a 1080i (60Hz) signal up to 100 ft. from the source, or a 1080p
(60Hz) signal up to 50 ft. from the source
• RJ45-style wallplate allows for the use of standard Cat5e/6 patch
cables; 110 punchdown connection not required
• No external power required
5
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
5
10/24/2011 10:01:17 AM
Product Features
B126-110
• HDMI over Cat5 Active Extender Remote/Repeater Unit (Box-style)
• Extends and expands Tripp Lite HDMI over Cat5 installation, allowing
multiple monitors to be located at different points in a chain of up to
700 ft.
• Extends a 1080i (60Hz) signal up to 175 ft., or a 1080p (60Hz)
signal up to 125 ft. from the local transmitter unit to the first remote/
repeater unit in the installation
• Extends a 1080i (60Hz) signal up to an additional 175 ft., or a
1080p (60Hz) signal up to an additional 125 ft. from each remote/
repeater unit to the next unit in the chain. In a full 4 level daisychain
installation, a 1080i (60Hz) signal can be extended up to 700 ft.,
or a 1080p (60Hz) signal up to 500 ft. from the source to the last
remote unit in the chain.
• Connect up to 4 remote units (3 remote/repeaters and 1 receiver),
with a monitor located at each point in the chain
• Features a built-in Equalization control for video image adjustment
• Includes mounting hardware that allows the unit to be wall-mounted,
rack-mounted or pole-mounted
Optional Accessories:
• B132-004-RB 1U Rackmount Bracket
• N202-Series Cat6 24AWG, solid wire patch cables
• P568-Series High-Speed HDMI cables
6
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
6
10/24/2011 10:01:17 AM
Mounting Instructions (select models only)
The B126-002, B126-004, B126-1A1, B126-1A0 and B126-110
come with mounting hardware that allows them to be mounted in
a variety of ways. The following images show the different ways the
included mounting brackets can be attached for different mounting
methods. Note: The B126-004 can also be mounted to a Tripp Lite
B132-004-RB 1U Rackmount Bracket. Up to 3 B126-004 local units
can be connected to a B132-004-RB.
Wallmount
19” Rackmount
Pole Mount
7
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
7
10/24/2011 10:01:19 AM
Standard Extender Kit Installation
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire
cabling.
3) The B126-1A1 and B126-1A1-WP are set to transmit a stereo audio
signal by default. Press the Audio button on the local unit to switch to
7.1-channel surround-sound audio.
4) The installation diagram shows a B126-1A1 unit. The B126-1A1-WP
installation is the same, except there is no local monitor port.
OPTIONAL LOCAL
MONITOR
BLU-RAY
LOCAL
REMOTE
TRANSMITTER
RECEIVER
Up to 200 ft. at 1080i (60Hz)
Up to 150 ft. at 1080p (60Hz)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
8
10/24/2011 10:01:20 AM
Standard Extender Kit Installation
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-1A1 or
B126-1A1-WP local unit using a Tripp Lite P568-Series HDMI Cable.
3
4
Optional for B126-1A1: Connect a local monitor to the LOCAL port
on the B126-1A1 local unit using a Tripp Lite P568-Series HDMI
Cable.
Connect the external power supply to the local unit and plug it into
a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or
Uninterruptible Power Supply (UPS). The green LED illuminates to
indicate the unit is receiving power from the external power supply.
5
6
Using Cat5e/6 cable, connect the RJ45 port on the local unit to the
RJ45 port on the remote unit.
Connect the external power supply to the remote unit and plug it
into a Tripp Lite Surge Suppressor, PDU or UPS. The green LED
illuminates to indicate the unit is receiving power from the external
power supply. The orange LED illuminates to indicate the unit is
connected to a powered ON local unit.
7
8
Connect the remote unit’s HDMI port to a monitor using a Tripp Lite
P568-Series HDMI Cable.
Turn on the power to the HDMI source. The orange LED on the
local unit illuminates to indicate a signal is being received from the
source.
9
If necessary, use the Equalization control on the remote unit to
adjust the video image. Note: An improper Equalization setting
can cause the monitor not to display a picture at all. Try each
Equalization setting until an acceptable picture is displayed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd
9
10/24/2011 10:01:20 AM
Extender Kit with Remote/Repeater Installation
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire
cabling.
3) The B126-1A1 and B126-1A1-WP are set to transmit a stereo audio
signal by default. Press the Audio button on the local unit to switch to
7.1-channel surround-sound audio.
4) The installation diagram shows a B126-1A1 unit. The B126-1A1-WP
installation is the same, except there is no local monitor port.
Up to 175 ft. at 1080i (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz) Up to 125 ft. at 1080p (60Hz)
OPTIONAL LOCAL
MONITOR
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
BLU-RAY
B126-1A1 LOCAL
TRANSMITTER
B126-1A1 REMOTE
RECEIVER
B126-110 REMOTE B126-110 REMOTE B126-110 REMOTE
REPEATER REPEATER REPEATER
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-1A1 or
B126-1A1-WP using a Tripp Lite P568-Series HDMI Cable.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 10
10/24/2011 10:01:21 AM
Extender Kit with Remote/Repeater Installation
3
4
Optional for B126-1A1: Connect a local monitor to the LOCAL
HDMI port using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the local unit and plug it into a
Tripp Lite Surge Suppressor, PDU or UPS. The green LED illuminates
to indicate the unit is receiving power from the external power
supply.
5
6
7
Using Cat5e/6 cable, connect the RJ45 port on the local unit to the
RJ45 INPUT port on the B126-110 remote/repeater unit.
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the green RJ45 LEDs illuminate to indicate the unit
is receiving power.
Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).
To connect additional remote/repeater units, proceed to step 8. To finish
your installation with the B126-1A1 or B126-1A1-WP remote receiver
unit, proceed to step 12.
8
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first
remote/repeater unit to the RJ45 INPUT port on a second remote/
repeater unit.
9
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit you just added using a Tripp Lite P568-Series HDMI Cable.
10
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the green RJ45 LEDs illuminate to indicate the unit
is receiving power.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 11
10/24/2011 10:01:21 AM
Extender Kit with Remote/Repeater Installation
11
To add a third remote/repeater unit, repeat steps 8 through 10.
To finish your installation with the B126-1A1 or B126-1A1-WP
remote receiver unit, proceed to step 12.
12
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last
remote/repeater unit to the RJ45 INPUT port of the B126-1A1 or
B126-1A1-WP remote receiver unit.
13
14
Connect a monitor to the HDMI OUTPUT port on the remote receiver
unit using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote receiver unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
LED illuminates to indicate the unit is receiving power from the
external power supply. The orange LED illuminates to indicate the
unit is connected to a powered ON remote/repeater unit.
15
16
Turn on the power to the HDMI source. The orange LED on the
local unit illuminates to indicate a signal is being received from the
source.
If necessary, use the Equalization control on the remote/repeater
unit(s) and remote receiver unit to adjust the video image. Note: An
improper Equalization setting can cause the monitor not to display
a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 12
10/24/2011 10:01:21 AM
Standard Extender/Splitter Installation
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series cables are made with 24 AWG solid wire
cabling.
3) The B126-002 and B126-004 are set to transmit a stereo audio
signal by default. Press the Audio button on the B126-002 or
B126-004 to switch to 7.1-channel surround-sound audio.
4) The installation diagram shows the B126-004 local transmitter unit.
The B126-002 installation is the same except there are only
2 remote ports and no local monitor port.
Up to 100 ft. at 1080i (60Hz) Up to 200 ft. at 1080i (60Hz)
Up to 50 ft. at 1080p (60Hz) Up to 150 ft. at 1080p (60Hz)
B126-1A0-WP-1
B126-1A0
B126-1P0-WP-1
B126-1P0
B126-004
BLU-RAY
OPTIONAL LOCAL
MONITOR
13
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 13
10/24/2011 10:01:21 AM
Standard Extender/Splitter Installation
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-002 or
B126-004 using a Tripp Lite P568-Series HDMI Cable.
3
4
Optional for B126-004: Connect an HDMI monitor to the LOCAL
port on the B126-004 using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the B126-002 or B126-004
local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS.
The green RJ45 LEDs and the red Power LED on the B126-004, and
the green RJ45 LEDs on the B126-002, will illuminate to indicate
power is being received from the external power supply.
5
Using Cat5e/6 cable, connect one of the RJ45 output ports on the
local unit to the RJ45 input port on a B126-1P0, B126-1A0,
B126-1P0-WP-1 or B126-1A0-WP-1 remote unit.
6
7
Repeat step 5 for each additional remote unit you are connecting.
B126-1A0 and B126-1A0-WP-1 only: Connect the external power
supply to the B126-1A0 or B126-1A0-WP-1, and plug it into a
Tripp Lite Surge Suppressor, PDU or UPS. The green and orange
LEDs illuminate, with the green LED indicating the unit is receiving
power from the external power supply, and the orange LED indicating
the unit is connected to a powered ON local unit via Cat5e/6 cable.
8
9
Repeat step 7 for each additional B126-1A0 or B126-1A0-WP-1 in
the installation.
Connect the B126-1P0 HDMI connector to a monitor; or, connect
the B126-1P0-WP-1, B126-1A0 or B126-1A0-WP-1 to a monitor
using a Tripp Lite P568-Series HDMI Cable. Both the green and
orange RJ45 LEDs on the B126-1P0, and the green LED on the
B126-1P0-WP-1, illuminate to indicate the unit is receiving power
from the connected monitor.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 14
10/24/2011 10:01:21 AM
Standard Extender/Splitter Installation
10
Repeat step 9 for each additional monitor you are connecting.
11
Turn on the power to the HDMI source. The orange RJ45 LEDs
illuminate on the B126-002 and B126-004 to indicate the unit
is receiving a signal from the source. The screen should now be
displayed on the connected monitors.
12
If necessary, use the Equalization control on the B126-1A0 or
B126-1A0-WP-1 to adjust the video image.
Note: An improper Equalization setting can cause the monitor not to
display a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 15
10/24/2011 10:01:21 AM
Extender/Splitter with Remote/Repeater Installation
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire
cabling.
3) The B126-002 and B126-004 are set to transmit a stereo audio
signal by default. Press the Audio button on the local unit to switch to
7.1-channel surround-sound audio.
4) The installation diagram shows the B126-004. The B126-002
installation will be the same, except there are only 2 remote ports
and there is no local monitor port.
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
B126-004 LOCAL
TRANSMITTER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
OPTIONAL LOCAL
MONITOR
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
BLU-RAY
B126-1A0-WP-1
REMOTE RECEIVER
16
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 16
10/24/2011 10:01:23 AM
Extender/Splitter with Remote/Repeater Installation
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-002 or
B126-004 using a Tripp Lite P568-Series HDMI Cable.
3
4
Optional for B126-004: Connect a local monitor to the LOCAL
HDMI port using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the local unit and plug it into
a Tripp Lite Surge Suppressor, PDU or UPS. The green RJ45 LEDs
illuminate to indicate power is being received from the external
power supply. An additional Red LED on the B126-004 also
illuminates to indicate that power is being received.
5
Using Cat5e/6 cable, connect one of the RJ45 output ports on the
local unit to the RJ45 input port on the B126-110 remote/repeater
unit.
6
7
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the Green RJ45 LEDs illuminate to indicate the unit
is receiving power.
Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).
To connect additional remote/repeater units, proceed to step 8. To finish
your installation with a B126-1A0 or B126-1A0-WP-1 remote receiver
unit, proceed to step 12.
8
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first
remote/repeater unit to the RJ45 INPUT port on a second remote/
repeater unit.
9
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit that you just added using a Tripp Lite P568-Series HDMI Cable.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 17
10/24/2011 10:01:23 AM
Extender/Splitter with Remote/Repeater Installation
10
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the green RJ45 LEDs illuminate to indicate the unit
is receiving power.
11
12
To add a third remote/repeater unit, repeat steps 8 through 10.
To finish your installation with a B126-1A0 or B126-1A0-WP-1
remote receiver unit, proceed to step 12.
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last
remote/repeater unit to the RJ45 INPUT port on a B126-1A0 or
B126-1A0-WP-1 remote receiver unit.
13
14
Connect a monitor to the HDMI OUTPUT port on the remote receiver
unit using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote receiver unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
LED illuminates to indicate the unit is receiving power from the
external power supply. The orange LED illuminates to indicate the
unit is connected to a powered ON remote/repeater unit.
15
16
Repeat steps 5 through 14 for each additional RJ45 output port on
the local transmitter unit.
Turn on the power to the HDMI source. The orange RJ45 LEDs on
the local unit illuminate to indicate a signal is being received from
the source.
17
If necessary, use the Equalization control on the remote/repeater
unit(s) and remote receiver unit to adjust the video image. Note: An
improper Equalization setting can cause the monitor not to display
a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 18
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain Installation (B126-004 only)
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series cables are made with 24 AWG solid wire
cabling.
3) The B126-004 is set to transmit a stereo audio signal by default.
Press the Audio button on the B126-004 to switch to 7.1-channel
surround-sound audio.
4) Using the B126-1A0 and B126-1A0-WP-1, a 1080i (60 Hz) signal
can be extended up to 200 ft. from the source, or a 1080p (60 Hz)
signal up to 150 ft. from the source. Using a B126-1P0 or
B126-1P0-WP-1, a 1080i (60Hz) signal can be extended up to
100 ft. from the source, or a 1080p (60Hz) signal up to 50 ft.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 19
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain Installation (B126-004 only)
Level 1
BLU-RAY
Level 2
Level 3
OPTIONAL LOCAL MONITOR
20
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 20
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain Installation (B126-004 only)
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-004 using
a Tripp Lite P568-Series HDMI Cable.
3
Connect the LOCAL port on the B126-004 to the INPUT port on a
second B126-004 using the included 1-ft. HDMI daisy-chain cable.
4
5
Repeat step 3 if you want to connect a third B126-004.
Optional: Connect a local monitor to the LOCAL HDMI port of the
last B126-004 using a Tripp Lite P568-series HDMI cable.
6
Connect the external power supply to the first B126-004 in the
daisy-chain and plug it into a Tripp Lite Surge Suppressor, PDU or
UPS. The green RJ45 LEDs and the red Power LED on the B126-
004 will illuminate to indicate power is being received from the
external power supply.
7
8
Repeat step 6 for each additional B126-004 in the daisy-chain.
Using Cat5e/6 cable, connect one of the RJ45 output ports on the
local unit to the RJ45 input port on a B126-1P0, B126-1A0,
B126-1P0-WP-1 or B126-1A0-WP-1 remote unit.
9
Repeat step 8 for each additional remote unit you are connecting.
10
B126-1A0 and B126-1A0-WP-1 only: Connect the external power
supply to the B126-1A0 or B126-1A0-WP-1, and plug it into a Tripp
Lite Surge Suppressor, PDU or UPS. The green and orange LEDs
illuminate, with the green LED indicating the unit is receiving power
from the external power supply, and the orange LED indicating the
unit is connected to a powered ON local unit via Cat5e/6 cable.
11
Repeat step 10 for each additional B126-1A0 or B126-1A0-WP-1 in
the installation.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 21
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain Installation (B126-004 only)
12
Connect the B126-1P0 HDMI connector to a monitor; or, connect
the B126-1P0-WP-1, B126-1A0 or B126-1A0-WP-1 to a monitor
using a Tripp Lite P568-Series HDMI Cable. Both the green and
orange RJ45 LEDs on the B126-1P0, and the green LED on the
B126-1P0-WP-1, illuminate to indicate the unit is receiving power
from the connected monitor.
13
14
Repeat step 12 for each additional monitor you are connecting.
Turn on the power to the HDMI source. The orange RJ45 LEDs
illuminate on the B126-004 to indicate the unit is receiving a
signal from the source. The screen should now be displayed on the
connected monitors.
15
If necessary, use the Equalization control on the B126-1A0 or
B126-1A0-WP-1 to adjust the video image. Note: An improper
Equalization setting can cause the monitor not to display a picture
at all. Try each Equalization setting until an acceptable picture is
displayed.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 22
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain with
Remote/Repeater Installation (B126-004 only)
Notes:
1) Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2) To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. Higher gauge cabling, such as 26 AWG, has a
more limited transmission capability than lower gauge cabling. All
Tripp Lite N202-Series Cat6 cables are made with 24 AWG solid wire
cabling.
3) The B126-004 is set to transmit a stereo audio signal by default.
Press the Audio button on the local unit to switch to 7.1-channel
surround-sound audio.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 23
10/24/2011 10:01:23 AM
Extender/Splitter Daisy-Chain with
Remote/Repeater Installation (B126-004 only)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
Up to 175 ft. at 1080i (60Hz)
Up to 125 ft. at 1080p (60Hz)
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
B126-004 LOCAL
TRANSMITTER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-1A0-WP-1
REMOTE RECEIVER
OPTIONAL LOCAL
MONITOR
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
B126-110 REMOTE/
REPEATER
BLU-RAY
B126-1A0-WP-1
REMOTE RECEIVER
DAISY CHAIN
UP TO
3 LEVELS
B126-004 LOCAL
TRANSMITTER
24
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 24
10/24/2011 10:01:26 AM
Extender/Splitter Daisy-Chain with
Remote/Repeater Installation (B126-004 only)
1
2
Make sure the HDMI source is powered OFF.
Connect the HDMI source to the INPUT port on the B126-004 using
a Tripp Lite P568-Series HDMI Cable.
3
Connect the LOCAL port on the B126-004 to the INPUT port on a
second B126-004 using the included 1-ft. HDMI daisy-chain cable.
4
5
Repeat step 3 if you want to connect a third B126-004.
Optional: Connect a local monitor to the LOCAL HDMI port of the
last B126-004 using a Tripp Lite P568-series HDMI cable.
6
Connect the external power supply to the first B126-004 in the
daisy-chain and plug it into a Tripp Lite Surge Suppressor, PDU or
UPS. The green RJ45 LEDs and the red Power LED on the
B126-004 will illuminate to indicate power is being received from
the external power supply.
7
8
Repeat step 6 for each additional B126-004 in the daisy-chain.
Using Cat5e/6 cable, connect one of the RJ45 output ports on the
local unit to the RJ45 input port on the B126-110 remote/repeater
unit.
9
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit using a Tripp Lite P568-Series HDMI Cable.
10
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the green RJ45 LEDs illuminate to indicate the unit
is receiving power.
Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).
To connect additional remote/repeater units, proceed to step 11. To
finish your installation with a B126-1A0 or B126-1A0-WP-1 remote
receiver unit, proceed to step 15.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 25
10/24/2011 10:01:26 AM
Extender/Splitter Daisy-Chain with
Remote/Repeater Installation (B126-004 only)
11
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the first
remote/repeater unit to the RJ45 INPUT port on a second remote/
repeater unit.
12
13
Connect a monitor to the HDMI OUTPUT port on the remote/repeater
unit that you just added using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote/repeater unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
power LED and the green RJ45 LEDs illuminate to indicate the unit
is receiving power.
14
15
To add a third remote/repeater unit, repeat steps 11 through 13. To
finish your installation with a B126-1A0 or B126-1A0-WP-1 remote
receiver unit, proceed to step 15.
Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the last
remote/repeater unit to the RJ45 INPUT port on a B126-1A0 or
B126-1A0-WP-1 remote receiver unit.
16
17
Connect a monitor to the HDMI OUTPUT port on the remote receiver
unit using a Tripp Lite P568-Series HDMI Cable.
Connect the external power supply to the remote receiver unit and
plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The green
LED illuminates to indicate the unit is receiving power from the
external power supply. The orange LED illuminates to indicate the
unit is connected to a powered ON remote/repeater unit.
18
19
Repeat steps 8 through 17 for each additional RJ45 output port on
the local transmitter units.
Turn on the power to the HDMI source. The orange RJ45 LEDs on
the local units illuminate to indicate a signal is being received from
the source.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 26
10/24/2011 10:01:26 AM
Extender/Splitter Daisy-Chain with
Remote/Repeater Installation (B126-004 only)
20
If necessary, use the Equalization control on the remote/repeater
unit(s) and remote receiver unit to adjust the video image. Note: An
improper Equalization setting can cause the monitor not to display
a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
Warranty & Warranty Registration
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for
a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this
warranty is limited to repairing or replacing (at its sole option) any such defective products. To
obtain service under this warranty, you must obtain a Returned Material Authorization (RMA)
number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned
to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid
and must be accompanied by a brief description of the problem encountered and proof of date
and place of purchase. This warranty does not apply to equipment which has been damaged by
accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP
LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use
of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or
otherwise.
WARRANTY REGISTRATION
You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 27
10/24/2011 10:01:26 AM
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations, when customers buy new electrical and electronic equipment from Tripp Lite they
are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis
(this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
WARNING
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to
change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA
201109206 • 933023
28
Download from Www.Somanuals.com. All Manuals Search And Download.
201109206-93-3023-EN.indd 28
10/24/2011 10:01:26 AM
|