CDP3235
CDP4235
CDP4235-T
CDP4635
CDP4635-T
CDX5550-L
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS14694/VS14693/VS14709/VS14692/VS14710/VS14691
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
6. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including
amplifiers) that produce heat.
8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade and the third prong are provided for your safety. If the plug does not fit into your outlet,
consult an electrician for replacement of the outlet.
9. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where if
emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily
accessible.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the equipment. When a cart is used, use caution when moving the cart/equipment combination to
avoid injury from tipping over.
12. Unplug this equipment when it will be unused for long periods of time.
13. Refer all servicing to qualified service personnel. Service is required when the unit has been damaged in any
way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit,
if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.
Download from Www.Somanuals.coimi . All Manuals Search And Download.
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European
Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the
European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum Concentration
Actual Concentration
< 0,1%
Lead (Pb)
0,1%
0,1%
0,01%
0,1%
0,1%
0,1%
Mercury (Hg)
< 0,1%
Cadmium (Cd)
< 0,01%
Hexavalent Chromium (Cr6+)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers (PBDE)
< 0,1%
< 0,1%
< 0,1%
Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted
below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not specifically
mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic parts
(e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up to 0.4%
lead by weight and as a cooper alloy containing up to 4% lead by weight.
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2013. All rights reserved.
ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter® are registered trademarks of ViewSonic®
Corporation.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or
use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product
specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior
written permission from ViewSonic® Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please
For Your Records
Product Name:
CDP3235/CDP4235/CDP4235-T/CDP4635/CDP4635-T/CDX5550-L
ViewSonic LCD Monitor
Model Number:
Document Number:
VS14694/VS14693/VS14709/VS14692/VS14710/VS14691
CDP3235_CDP4235_CDP4235-T_CDP4635_CDP4635-T_CDX5550-L_
UG_ENG Rev. 1C 05-16-13
Serial Number:
Purchase Date:
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank you for being part of
Smarter, Greener Computing. Please visit ViewSonic website to learn more.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Table Of Contents
1. Unpacking and Installation............................................................................................................1
1.1. Unpacking ................................................................................................................................1
1.2. Package Contents....................................................................................................................1
1.3. Installation Notes......................................................................................................................1
1.4. Installing and Removing Table Stands (optional).....................................................................2
1.5. Installing and Removing OPS module (CP4235/CDP4635/CDX5550-L series) (optional)......3
1.6. Mounting on a Wall...................................................................................................................4
2. Parts and Functions .......................................................................................................................5
2.1. Control Panel ...........................................................................................................................5
2.2. Input/Output Terminals.............................................................................................................6
2.3. Remote Control........................................................................................................................7
2.3.1. General functions...........................................................................................................7
2.3.2. Inserting the batteries in the remote control...................................................................8
2.3.3. Handling the remote control...........................................................................................8
2.3.4. Operating range of the remote control...........................................................................8
3. Connecting External Equipment ...................................................................................................9
3.1. Using the Switch Cover............................................................................................................9
3.2. Connecting External Equipment (DVD/VCR/VCD) ..................................................................9
3.2.1. Using COMPONENT video input.................................................................................10
3.2.2. Using HDMI video input ...............................................................................................10
3.3. Connecting a PC....................................................................................................................11
3.3.1. Using VGA input...........................................................................................................11
3.3.2. Using DVI input............................................................................................................11
3.3.3. Using HDMI input.........................................................................................................12
3.4. External Audio Connection.....................................................................................................13
3.4.1. Connecting external speakers .....................................................................................13
3.4.2. Connecting an external audio device...........................................................................13
3.5. Connecting Multiple Displays in a Daisy-chain Configuration................................................14
3.5.1. Video connection .........................................................................................................14
3.5.2. Audio connection .........................................................................................................14
4. OSD Menu......................................................................................................................................15
4.1. Navigating the OSD Menu ....................................................................................................15
4.1.1. Navigating the OSD menu using the remote control....................................................15
4.1.2. Navigating the OSD menu using the display’s control buttons ....................................15
4.2. OSD Menu Overview .............................................................................................................15
4.2.1. PICTURE menu ...........................................................................................................15
4.2.2. SCREEN menu............................................................................................................16
4.2.3. AUDIO menu................................................................................................................17
Download from Www.Somanuals.com. All Manuals Search And Download.
v
4.2.4. PIP menu .....................................................................................................................17
4.2.5. CONFIGURATION1 menu...........................................................................................18
4.2.6. CONFIGURATION2 menu...........................................................................................19
4.2.7. CONFIGURATION3 menu...........................................................................................20
4.2.8. ADVANCED OPTION menu ........................................................................................21
5. Input Mode.....................................................................................................................................23
6. Cleaning and Troubleshooting....................................................................................................24
6.1. Cleaning.................................................................................................................................24
6.2. Troubleshooting......................................................................................................................25
7. Technical Specifications..............................................................................................................26
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
1.
Unpacking and Installation
1.1. Unpacking
•
•
•
•
This product is packed in a carton, together with the standard accessories.
Any other optional accessories will be packed separately.
Due to the size and weight of this display it is recommended for two people to move it.
After opening the carton, ensure that the content is in good condition and complete.
1.2. Package Contents
Please verify that you received the following items with your package content:
•
•
•
•
•
•
•
CD ROM (Optional)
POWER
SMART
Remote control with AAA batteries
Power cord (1.8 m)
VIDEO
AUDIO
SOURCE
SOURCE
PIP
ON/OFF
INPUT
CHANGE
CONTRAST
BRIGHTNESS
DISPLAY
MENU
VGA cable (1.8 m)
SET
*
*
AUTO
ADJUST
EXIT
For EU
For China
VOL UP
Quick Installation Guide
Power switch cover
MUTE
VOL DOWN
CD ROM (Optional)
Screw for Power switch cover
(M3x8)
Remote Control
and AAA Batteries
Power switch cover
(Exclusive of CDX5550-L)
•
•
BNC-to-RCA adapter (x3)
USB cable (CDP4635-T/
CDP4635-T)
*
*
For UK
For North America
Screw for Power switch cover BNC-RCA adapter x 3
(M3 x 8) x 1
(Exclusive of CDX5550-L)
USB cable
Video Signal Cable
(D-SUB to D-SUB Cable)
* The supplied power cord varies depending on destination.
NOTES:
•
Please make sure that for all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been
approved by and complies with the safety regulations of the particular country.
•
You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
•
Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please
consult your service agent.
•
The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should
be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as
not to shorten the service life of the electronic components.
•
The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be
experienced.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1.4. Installing and Removing Table Stands (optional)
To install table stands:
1. Power off the display.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. After inserting the stand in the guide block, tighten the screws on both sides of the display.
NOTE: The long-end side of the stand should face to the front while installing.
Carrying handle
Thumbscrews
Longer portions face the front
Table stand
CDP3235: STND-022
CDP4235/CDP4635:STND-020
Carrying handle
Thumbscrews
Table stand
CDX5550-L : STND-021
To remove table stands:
1. Power off the display.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. Remove screws using a screwdriver and place them in a safe place for reuse.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1.5. Installing and Removing OPS module (CDP4235/CDP4635/CDX5550-L series) (optional)
To install OPS Module:
1. Power off the display.
2. Remove the cover of OPS after take screw off.
3. Insert OPS module and then fix by screw.
NOTE: Keep the OPS cover for future use.
Screw
Screw
OPS
To remove OPS Module:
1. Power off the display.
2. Remove screw and plug out OPS module.
3. Install OPS cover and then fix by screw.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
1.6. Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a
mounting interface that complies with TUV-GS and/or UL1678 standard in North America.
100
200
100
400
Protective Sheet
Protective Sheet
400
200
Table
Tabletop stand
Table
Tabletop stand
CDP3235/CDP4235/CDP4635 series
CDX5550-L
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as
not to scratch the screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to
the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and
tighten them securely.
Caution:
To prevent the display from falling:
•
For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed
installation instructions, refer to the guide received with the respective bracket.
•
To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure
to consult the bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects
as shown in the diagram below.
100 mm
100 mm
100 mm
100 mm
Download from Www.Somanuals.com. All Manuals Search And Download.
4
2.
Parts and Functions
2.1. Control Panel
9
9
10
MUTE INPUT
MENU
MENU
10
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
CDP3235/CDP4235/CDP4635 series
CDX5550-L
1
8
POWER button
MENU button
Use this button to turn the display on or put the display to
standby.
Return to previous menu while OSD menu is on, or to
activate the OSD menu when OSD menu is off.
NOTE: “Keyboard Control Lock Mode” This function
completely disables the access to all Keyboard Control
functions. To enable or disable the keyboard control
lock, press both [ ] and [ ] buttons and hold down
continuously for more than 3 (three) seconds.
2
3
MUTE button
Switch the audio mute ON/OFF.
INPUT button
•
Use this button to select the input source.
9
Remote control sensor and power status indicator
•
When the On Screen Display menu is active, this is also
used as the [SET] button.
•
Receives command signals from the remote control.
•
Indicates the operating status of the display:
4
5
6
7
[ ] button
- Lights green when the display is turned on
- Lights red when the display is in standby mode
- Lights amber when the display enters DPMS mode
Increase the adjustment while OSD menu is on, or increase
the audio output level while OSD menu is off.
[ ] button
- When {SCHEDULE} is enabled, the light blinks green
and red
Decrease the adjustment while OSD menu is on, or
decrease the audio output level while OSD menu is off.
- If the light blinks red, it indicates that a failure has been
detected
[
] button
Move the highlight bar up to adjust the selected item while
OSD menu is on.
- Off when the main power of the display is turned off
10
OPS slot (exclusive of CDP3225)
Expansion slot adapter for Open Pluggable
Specification(OPS) card
[
] button
Move the highlight bar down to adjust the selected item
while OSD menu is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2.2. Input/Output Terminals
CDP4235/CDP4635 series
CDX5550-L
CDP3235
15
15
15
CDP3235
(OUT)
(OUT)
(IN)
Pr Pb
Y
1
3
2
(IN)
(IN)
1
2
3
4
5
6
7
8
9
10 11 12 10
13 14
CDP4235/CDP4635/CDX5550-L series
(OUT)
(OUT)
Pr Pb
Y
1
3
2
(IN)
(IN)
(IN)
2
1
3
4
5
6
7
8 16
9
10 11 12 10
13 14
1
2
3
10
11
MAIN POWER SWITCH
Press to switch the main power on/off.
AUDIO IN 1, 2, 3
Connect audio input from external AV device.
•
•
AUDIO IN 1: 3.5mm stereo phone jack
AC IN
AUDIO IN 2, 3: RCA phone jack
Connect the supplied power cord to the wall outlet.
VIDEO IN/OUT
RS232C (OUT/IN)
RS232C network input/output connection for the use of loop-
through function.
•
•
•
S-VIDEO IN (Mini DIN 4 pin): Connect the S-VIDEO (Y/
C separate signal) input.
VIDEO IN (BNC): Connect the composite video signal
input.
4
RJ-45
LAN control function for the use of remote control signal
from control center.
VIDEO OUT (BNC): Connect the composite video signal
output from VIDEO IN (BNC).
5
6
VGA OUT (D-Sub)
Output the VGA signal from the VGA IN (D-Sub).
12
AUDIO OUT R/L (RCA)
Connect the audio signal output from AUDIO IN 1, 2, or 3
jack to an external AV device.
DVI-D IN
Connect the DVI-D output of a PC, or the HDMI output of an
AV device by using a DVI-HDMI cable.
13
14
15
16
SPEAKERS OUT R/L
Connect the audio output to external speakers.
7
HDMI IN
SPEAKER SWITCH
Press to switch the internal speaker on/off.
Connect the HDMI output of an AV device, or the DVI-D
output of a PC by using a DVI-HDMI cable.
KENSINGTON LOCK
For security and theft prevention.
8
9
VGA IN (D-Sub)
Connect the computer VGA output.
USB-B
Touch connector to PC.
COMPONENT IN (BNC)
Connect the component YPbPr output from external AV
device.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
5
6
[DISPLAY] button
Press to turn on/off the information OSD displayed on the
upper right corner of the screen.
2.3. Remote Control
2.3.1. General functions
[ ] button
•
•
•
Press to move the selection left in OSD menu.
Press to decrease the value in OSD menu.
Press to move the sub-picture left in PIP mode.
POWER
1
10
VIDEO
SOURCE
AUDIO
SOURCE
SMART
7
8
[SET] button
Press to activate the setting inside the OSD menu.
2
11
12
[AUTO ADJUST] button
PIP
Press to run the Auto Adjust function.
3
4
ON/OFF
INPUT
CHANGE
NOTE:This button is functional for VGA input only.
13
9
[MUTE] button
Press to turn the mute function on/off.
CONTRAST
BRIGHTNESS
14
15
5
DISPLAY
MENU
10
[VIDEO SOURCE] button
Press to toggle Video Source Menu. Press [ ] or [
] button to select one of the video sources among HDMI,
DVI-D, VGA, DVD / HD, VIDEO-S, or VIDEO . Press [SET]
button to confirm and exit.
SET
16
6
7
8
17
18
AUTO
EXIT
ADJUST
11
12
[AUDIO SOURCE] button
VOL UP
19
20
Press to toggle Audio Source Menu. Press [ ] or [ ] button
to select one of the audio sources among HDMI, AUDIO1,
AUDIO2, or AUDIO3. Press [SET] button to confirm and
exit.
MUTE
9
VOL DOWN
Picture Format button
Press to switch screen aspect ratio.
•
•
For PC signal: FULL, NORMAL, CUSTOM and REAL.
For Video signal: FULL, NORMAL, DYNAMIC, CUSTOM
and REAL.
13
14
[BRIGHTNESS] button
Press to toggle Brightness Menu. Press [ ] or [ ] button to
adjust the value. Press [MENU] button to confirm and exit.
[
] button
•
Press to move the selection up in OSD menu.
•
Press to move the sub-picture up in PIP mode.
1
2
[POWER] button
Press to switch on the display from standby mode. Press
again to turn it off and back into standby mode.
15
16
[MENU] button
Press to turn the OSD menu on/off.
[SMART] button
[ ] button
Press to activate Smart Menu. Press [ ] or [ ] button to
select menu options. Press [SET] button to confirm and exit
the selection.
•
•
•
Press to move the selection right in OSD menu.
Press to increase the value in OSD menu.
Press to move the sub-picture right in PIP mode.
•
•
•
Standard: Used for normal images (factory setting)
Highbright: Used for moving image such as Video
sRGB: Used for text based images
17
18
[EXIT] button
Press to turn back to the previous OSD menu.
[
•
] button
3
4
[PIP] (Picture In Picture) button
[ON/OFF]: Turn PIP mode ON/OFF.
Press to move the selection down in OSD menu.
•
Press to move the sub-picture down in PIP mode.
[INPUT]:
Select the input signal for the sub-picture.
[CHANGE]: Toggle between the main picture and sub
19
20
[VOL UP] button
Press to increase the audio output level.
picture.
[CONTRAST] button
Press to activate Contrast Menu. Press [ ] or [ ] button to
adjust the value. Press [MENU] button to confirm and exit.
[VOL DOWN] button
Press to decrease the audio output level.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
2.3.2. Inserting the batteries in the remote
control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
2.3.4. Operating range of the remote control
Point the top of the remote control toward the display’s remote
control sensor when pressing a button.
Use the remote control within a distance of less than 10m/33ft
from the display’s sensor, and a horizontal and vertical angle of
less than 30 degrees.
NOTE: The remote control may not function properly when the
remote control sensor on the display is under direct
sunlight or strong illumination, or when there is an
obstacle in the path of signal transmission.
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications
inside the battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be
sure to follow these instructions:
•
Place “AAA” batteries matching the (+) and (–) signs on each
battery to the (+) and (–) signs of the battery compartment.
•
•
Do not mix battery types.
Do not combine new batteries with used ones. It causes
shorter life or leakage of batteries.
30
30
•
Remove the dead batteries immediately to prevent them
from liquid leaking in the battery compartment. Don’t touch
exposed battery acid, it cause damage to your skin.
NOTE: If you do not intend to use the remote control for a long
period, remove the batteries.
2.3.3. Handling the remote control
CDP3235/CDP4235/CDP4635 series
•
•
Do not subject to strong shock.
Do not allow water or other liquid to splash the remote
control. If the remote control gets wet, wipe it dry
immediately.
•
•
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the remote
control.
30
30
CDX5550-L
Download from Www.Somanuals.com. All Manuals Search And Download.
8
3.
Connecting External Equipment
3.1. Using the Switch Cover
A cover for the power switch is provided to prevent the display
from being turned on or off accidentally.
To lock the cover into position:
1. Align and insert the cover to the indentation located beside
the main switch.
2. Use the screw to lock the cover.
CDP3235:
1
2
Screw
Power switch cover
CDP4235/CDP4635 series:
1
Screw
2
Power switch cover
Download from Www.Somanuals.com. All Manuals Search And Download.
9
3.2. Connecting External Equipment (DVD/VCR/VCD)
3.2.1. Using COMPONENT video input
COMPONENT
(YPbPr)
Audio Output
DVD / VCR / VCD
COMPONENT
(YPbPr)
To [AUDIO IN 2, 3]
3.2.2. Using HDMI video input
DVD / VCR / VCD
HDMI connector
HDMI connector
Download from Www.Somanuals.c1om0. All Manuals Search And Download.
3.3. Connecting a PC
3.3.1. Using VGA input
From analog VGA output
Mini D-Sub 15 pin
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [VGA IN]
3.3.2. Using DVI input
From DVI output
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [DVI IN]
Download from Www.Somanuals.com. All Manuals Search And Download.
11
3.3.3. Using HDMI input
From HDMI output
PC or IBM compatible
To [HDMI IN]
3.3.4. CONNECTING THE TOUCH MODULE
There are two ways to connect the touch module.
1. Connect the USB cable on the display to a PC.
The touch module supports easy Plug-and-Play operations. There is no need to install additional drivers on the PC.
2. Install an OPS (Open Pluggable Specification) module in to the slot on the rear of the display. Refer to the module’s documentation
for user instructions.
OPS module
From USB output
PC or IBM compatible
To [USB IN]
Download from Www.Somanuals.c1om2. All Manuals Search And Download.
3.4. External Audio Connection
3.4.1. Connecting external speakers
External speaker
3.4.2. Connecting an external audio device
To [AUDIO OUT]
RCA
Audio In
Stereo Amplifier
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
3.5. Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall.
NOTE: Maximum 9 displays can be used in a daisy-chain configuration.
3.5.1. Video connection
Connect one of the following:
•
•
•
Connect the [RS232C OUT] connector of display 1 to the [RS232C IN] connector of display 2.
Connect the [VGA OUT] connector of display 1 to the [VGA IN] connector of display 2.
Connect the [VIDEO OUT] connector of display 1 to the [VIDEO IN] connector of display 2.
To RS-232C IN
To RS-232C OUT
To RS-232C IN
PC
RS-232C Cable
RS-232C Cable
3.5.2. Audio connection
Do one the following connections:
•
•
•
Connect the [AUDIO OUT] connector of display 1 to the [AUDIO IN 2] OR [AUDIO IN 3] connector of display 2.
Connect the [VGA OUT] connector of display 1 to the [VGA IN] connector of display 2.
Connect the [VIDEO OUT] connector of display 1 to the [VIDEO IN] connector of display 2.
To [AUDIO IN 1, 2, 3]
To [AUDIO OUT]
To [AUDIO IN 2, 3]
PC
Download from Www.Somanuals.c1om4. All Manuals Search And Download.
4.2. OSD Menu Overview
4.2.1. PICTURE menu
4.
OSD Menu
An overall view of the On-Screen Display (OSD) structure is
shown below. You can use it as a reference for further adjusting
your display.
PICTURE
4.1. Navigating the OSD Menu
BRIGHTNESS
CONTRAST
70
50
50
50
SHARPNESS
BLACK LEVEL
TINT
COLOR
COLOR TEMPERATURE
USER COLOR
GAMMA SELECTION
NOISE REDUCTION
FILM MODE
4.1.1. Navigating the OSD menu using the
remote control
NATIVE
NATIVE
1
MENU
PICTURE RESET
2
3
SET
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
EXIT
BRIGHTNESS
Adjust the overall image brightness by changing the intensity of
the LCD panel’s backlight.
1. Press [MENU] button on the remote control to display the
OSD menu.
CONTRAST
2. Press [ ] or [ ] button to choose the item you want to
adjust.
Adjust to sharpen the picture quality. The black portions of
the picture become richer in darkness and the white become
brighter.
3. Press [SET] button to enter the submenu.
SHARPNESS
4. In the submenu, press [ ] or [ ] button to toggle among
items, press [ ] or [ ] button to adjust settings. If there is a
Adjust to improve the image detail.
submenu, press [SET] button to enter the submenu.
BLACK LEVEL
5. Press [EXIT] button to return to the previous menu, or press
Adjust to change the image brightness.
[MENU] button to exit the OSD menu.
TINT
Use the [ ] or [ ] button to adjust. Press the [ ] button and
the flesh tone color turns slightly green. Press the [ ] button
and the flesh tone color turns slightly purple.
4.1.2. Navigating the OSD menu using the
display’s control buttons
1. Press [MENU] button to display the OSD menu.
NOTE: This item is functional for HDMI(Video mode), S-Video,
Video, and YPbPr inputs only.
2. Press [ ] or [ ] button to choose the item you want to
adjust.
COLOR
3. Press [SOURCE] button to enter the submenu.
Adjust to increase or decrease the intensity of colors in the
image.
4. In the submenu, press [ ] or [ ] button to toggle among
items, press [ ] or [ ] button to adjust settings. If there is a
submenu, press [SOURCE] button to enter the submenu.
NOTE: This item is functional for HDMI(Video mode), S-Video,
Video, and YPbPr inputs only.
5. Press [MENU] button to return to the previous menu, or
COLOR TEMPERATURE
press [MENU] button several times to exit the OSD menu.
Select a color temperature for the image. A lower color
temperature will have a reddish tint, whilst a higher color
temperature gives off a more bluish tint.
The options are: {3000K} / {4000K} / {5000K} / {6500K} / {7500K}
/ {9300K} / {10000K} / {NATIVE} / {USER}.
USER COLOR
With this function you can adjust the color tones of the image
precisely by changing the R (Red), G (Green) and B (Blue)
settings independently.
NOTE: This item is functional only when {COLOR
TEMPERATURE} is set to {USER}.
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
GAMMA SELECTION
V POSITION
Gamma is what controls the overall brightness of an image.
Images which are not corrected properly can appear too white
or too dark, so controlling the gamma properly can have a huge
influence on the overall picture quality of your display.
Press the [ ] button to move the image up, or [ ] to move the
image down.
CLOCK
Adjust the width of the image.
NOTE: This item is functional for VGA input only.
The options are: {NATIVE} / {2.2} / {2.4} / {S GAMMA}.
NOISE REDUCTION
CLOCK PHASE
Adjust to remove the noise in the image. You can select a
suitable noise reduction level.
Adjust to improve the focus, clarity and stability of the image.
NOTE: This item is functional for VGA input only.
The options are: {OFF} / {LOW} / {MIDDLE} / {HIGH}.
NOTE: This item is functional for HDMI(Video mode), S-Video,
ZOOM MODE
Video, and YPbPr inputs only.
The pictures you receive may be transmitted in 16:9 format (wide
screen) or 4:3 format (conventional screen). The 16:9 pictures
sometimes have a black band at the top and bottom of the
screen (letterbox format).
FILM MODE
Choose to turn on or off the film mode frame conversion
function.
This function allows you to optimize the picture display on
screen. The following zoom modes are available for:
•
{AUTO} - Enable the film mode frame conversion function
for movies and motion pictures. The display converts a
24 frames-per-second (24 fps) input signal format to DVD
video signal format. Once this function is enabled, it is
recommended that you set the {SCAN CONVERSION}
function to {PROGRESSIVE}.
•
•
PC mode: {FULL} / {NORMAL} / {CUSTOM} / {REAL}.
Video mode: {FULL} / {NORMAL} / {DYNAMIC} / {CUSTOM}
/ {REAL}.
FULL
•
{OFF} - Disable the film mode frame conversion function.
This mode is suitable for TV broadcasting and VCR signals.
This mode restores the correct
proportions of pictures transmitted in
16:9 using the full screen display.
PICTURE RESET
Reset all settings in the Picture menu to factory preset values.
NORMAL
The picture is reproduced in 4:3 format
and a black band is displayed on either
side of the picture.
4.2.2. SCREEN menu
DYNAMIC
Fill the entire screen by stretching 4:3
pictures non-proportionally.
SCREEN
AUTO SETUP
AUTO ADJUST
H POSITION
OFF
50
50
V POSITION
CLOCK
2200
66
CLOCK PHASE
ZOOM MODE
CUSTOM ZOOM
H RESOLUTION
V RESOLUTION
INPUT RESOLUTION
SCREEN RESET
CUSTOM
Choose to apply the custom zoom
FULL
settings in the Custom Zoom submenu.
1920
1080
1
REAL
2
3
This mode displays the image pixel-
by-pixel on screen without scaling the
original image size.
CUSTOM ZOOM
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
You can use this function to further customize the zoom settings
to suit the image you want to display.
AUTO SETUP
NOTE: This item is functional only when the {ZOOM MODE}
Use this function to let the display automatically optimize the
display of VGA input image.
setting is set to {CUSTOM}.
NOTE: This item is functional for VGA input only.
ZOOM
Expands the horizontal and vertical sizes
of the image simultaneously.
AUTO ADJUST
Choose to let the display detect and display available signal
sources automatically.
H ZOOM
•
{ON} - Set the display to display the image automatically
Expands the horizontal size of the image
only.
once a signal is connected.
•
{OFF} - Once a signal is connected, it can only be selected
manually.
H POSITION
Press the [ ] button to move the image to the right, or [ ] to
move the image to the left.
Download from Www.Somanuals.c1om6. All Manuals Search And Download.
4.2.4. PIP menu
V ZOOM
Expands the vertical size of the image
only.
PIP
PIP MODE
PIP SIZE
PIP AUDIO
OFF
SMALL
MAIN AUDIO
100
H POSITION
Moves the horizontal position of the
PIP H POSITION
image left or right.
PIP V POSITION
SUB INPUT
0
VIDEO
PIP RESET
PIP
V POSITION
Moves the vertical position of the image
up or down.
1
2
3
INPUT RESOLUTION
Set the resolution of the VGA input. This is only required when
the display is unable to detect the VGA input resolution correctly.
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
NOTE: This item is functional for VGA input only.
PIP MODE
Select the PIP (Picture-in-Picture) mode.
The options are:
•
•
•
•
{1024x768 / 1280x768 / 1360x768}
{1400x1050 / 1680x1050}
The options are: {OFF} / {PIP} / {POP} / {SBS ASPECT} / {SBS
FULL}.
{1600x1200 / 1920x1200}
PIP SIZE
{Auto}: Determines the resolution automatically.
Select the size of the sub picture in the PIP (Picture-in-Picture)
mode.
The selected settings will become effective after turning off the
power and turn it on again.
The options are: {SMALL} / {MIDDLE} / {LARGE}.
SCREEN RESET
PIP AUDIO
Reset all settings in the SCREEN menu to factory preset values.
Select the audio source in the PIP (Picture-in-Picture) mode.
•
•
{MAIN AUDIO} - Select audio from the main picture
4.2.3. AUDIO menu
{SUB AUDIO} - Select audio from the sub picture.
PIP H POSITION
AUDIO
Adjust the horizontal placement of the sub picture.
BALANCE
TREBLE
BASS
50
50
50
PIP V POSITION
AUDIO RESET
Adjust the vertical placement of the sub picture.
SUB INPUT
Select the input signal for the sub-picture.
1
PIP RESET
Reset all settings in the PIP menu to factory preset values.
2
3
NOTES:
•
The PIP function is available only for certain signal source
combinations as shown in the table below.
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
•
The availability of the PIP function will also depend on the
resolution of the input signal being used.
BALANCE
Adjust to emphasize left or right audio output balance.
Main Picture
Sub Picture
Card
OPS
DVI VGA HDMI YPbPr S-Video Video
TREBLE
DVI
VGA
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
O
O
O
O
X
O
O
O
O
X
X
X
X
X
O
O
X
Adjust to increase or decrease higher-pitched sounds.
BASS
HDMI
Adjust to increase or decrease lower-pitched sounds.
YPbPr
S-Video
Video
AUDIO RESET
X
O
X
O
Reset all settings in the AUDIO menu to factory preset values.
Card OPS
(O: PIP function available, X: PIP function unavailable)
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
By pressing the [PIP ON/OFF] button on the remote control, you
can change the mode in the order shown below:
SCHEDULE
TODAY
SBS ASPECT
SBS FULL
PIP
POP
OFF
2011 . 08 . 04
THU
20 : 19 : 55
1
2
ON OFF
INPUT
3
4
5
6
7
:
:
＿
＿
＿
＿
＿
The resolutions in the PIP and POP modes are configured as
follows:
EVERY DAY
WED
MON
THU
SUN
TUE
FRI
PIP SIZE {SMALL} : 320 x 240 pixels
{MIDDLE} : 480 x 320 pixels
{LARGE} : 640 x 480 pixels
POP SIZE: 474 x 355 pixels
SAT
EVERY WEEK
EXIT
MENU
+-:SEL
:RETURN
:EXIT MENU
2. Press [ ] or [ ] button to select a schedule item (item
number 1 ~ 7), and then press [SET] button to mark it the
item number.
NOTE: The images displayed in the sub picture always fit the
PIP sizes shown above irrespective of the aspect ratio
of the input image.
SCHEDULE
4.2.5. CONFIGURATION1 menu
TODAY
2011 . 08 . 04
THU
20 : 19 : 55
1
2
3
4
5
6
7
1
2
3
INPUT
＿
CONFIGURATION1
ON
OFF
OFF TIMER
SCHEDULE
OFF
:
:
＿
＿
＿
＿
DATE AND TIME
CONFIGURATION1 RESET
4
EVERY DAY
WED
MON
THU
SUN
TUE
FRI
EVERY WEEK
1
SAT
EXIT
MENU
+-:SEL
:RETURN
:EXIT MENU
2
3
3. Press [ ] or [ ] button to select the schedule:
1
POWER-ON schedule: Press [ ] or [ ] button to set
the hour and minute for the display to turn on.
2
POWER-OFF schedule: Press [ ] or [ ] button to set
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
the hour and minute for the display to turn off.
Select or leave an empty “__” for both the hour and minute
slot if you do not want to use this power-on or power-off
schedule.
OFF TIMER
Set the display to turn itself off to standby mode within an
amount of time specified.
3
INPUT-SOURCE selection: Press [ ] or [ ] button to
The options are: {OFF, 1HOUR ~ 24HOURS} from currrent time.
select an input source. If no input source is selected,
the input source will remain the same as last selected.
SCHEDULE
This function allows you to program up to 7 (seven) different
scheduled time intervals for the display to activate.
4
DATE schedule: Press [ ] button to select which day
in a week this schedule item will be take effect, and
then press the [SET] button.
You can select:
•
•
•
The time for the display to turn on and turn off.
The days in a week for the display to activate.
4. For more schedule settings, press [EXIT] button and then
repeat the steps above. A check mark in the box next to
the number of the schedule item indicates that the selected
schedule is in effect.
Which input source the display will use for each scheduled
activation period.
NOTE: You should set up current date and time in {DATE AND
NOTES:
TIME} menu before using this function.
•
•
•
The {EVERY DAY} selection in a schedule item takes priority
over the other weekly schedules.
1. Press [SET] button to enter the submenu.
If the schedule overlap, the scheduled power-on time takes
priority over scheduled power-off time.
If there are two schedule items programmed for the same
time, the highest numbered schedule takes priority. For
example, if schedule items #1 and #2 both set the display to
power on at 7:00 AM and off at 5:00 PM, then only schedule
item # 1 will take effect.
Download from Www.Somanuals.c1om8. All Manuals Search And Download.
DATE AND TIME
INFORMATION OSD
Adjust the current date and time for the display’s internal clock.
Set the period of time the information OSD displayed on the
upper right corner of the screen. The information OSD will
display when input signal is changed.
DATE AND TIME
The information OSD will remain on the screen with {OFF}
selection.
YEAR
MONTH
DAY
2011
08
04
The options are: {OFF, 3 SEC. ~ 10 SEC.}.
MONITOR INFORMATION
HOUR
20
MINUTE
20
Displays the information about your display, including MODEL
NAME and SERIAL.
DAYLIGHT SAVING TIME
CURRENT DATE TIME
OFF
MONITOR ID
2011 . 08 . 04
00 : 18 : 10
Set the ID number for controlling the display via the RS232C
connection. Each display must have a unique ID number when
multiple sets of this display are connected.
EXIT
MENU
:EXIT MENU
:SEL
+-:ADJ
:RETURN
1. Press [SET] button to enter the submenu.
IR CONTROL
2. Press [ ] or [ ] button to toggle among the {YEAR},
{MONTH}, {DAY}, {HOUR}, {MINUTE}, and {DAYLIGHT
SAVING TIME} settings.
Select the operation mode of the remote control unit when
multiple displays are connected via the RS232C connection.
•
{NORMAL} - All displays can be operated normally by the
3. Press [ ] or [ ] button to adjust all settings except
remote control.
{DAYLIGHT SAVING TIME}.
•
{LOCK} - Lock the remote control function of this display. To
unlock, press and hold the [DISPLAY] button on the remote
control for 5 (five) seconds.
CONFIGURATION1 RESET
Reset all settings in the CONFIGURATION1 menu to factory
preset values.
TILING
With this function you can create a single large-screen matrix
(video wall) that consists of up to 25 sets of this display (up to
5-set each at the vertical and horizontal side). This function
requires a daisy-chain connection.
4.2.6. CONFIGURATION2 menu
CONFIGURATION2
TILING
LANGUAGE
OFF
OSD TURN OFF
OSD H POSITION
OSD V POSITION
INFORMATION OSD
MONITOR INFORMATION
MONITOR ID
IR CONTROL
TILING
POWER ON DELAY
CLOSED CAPTION
CONFIGURATION2 RESET
45
H MONITORS
V MONITORS
POSITION
FRAME COMP.
ENABLE
1
1
1
50
50
3 SEC.
1
1
OFF
OFF
MENU
:EXIT MENU
OFF
2
EXIT
:RETURN
:SEL
+-:ADJ
Example: 2 x 2 screen matrix (4 displays)
H MONITORS = 2 displays
3
V MONITORS = 2 displays
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
H MONITORS
LANGUAGE
Select the language used in the OSD menu.
The options are: { } / { } / {
} / { } / { } / {
OSD TURN OFF
Position
} /
}.
1 2
3 4
{
} / {
Set the period of time the OSD menu stays on the screen.
The options are: {5 ~ 120} seconds.
OSD H POSITION
Adjust the horizontal position of the OSD menu.
OSD V POSITION
Adjust the vertical position of the OSD menu.
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
Example: 5 x 5 screen matrix (25 displays)
H MONITORS = 5 displays
not compliant with it, images may not be displayed
correctly.
V MONITORS = 5 displays
CONFIGURATION2 RESET
Reset all settings in the CONFIGURATION2 menu to factory
preset values.
1
6
2
7
3
8
4
9
5
4.2.7. CONFIGURATION3 menu
10
CONFIGURATION3
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
POWER SAVE
HEAT STATUS
SCREEN SAVER
SIDE BORDER COLOR
CONFIGURATION3 RESET
51
1
•
•
•
•
H MONITORS - Select the number of displays on the
2
3
horizontal side.
V MONITORS - Select the number of displays on the vertical
side.
POSITION - Select the position of this display in the screen
matrix.
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
FRAME COMP. - Choose to turn the frame compensation
function on or off. If turned on, the display will adjust the
image to compensate for the width of the display bezels in
order to accurately display the image.
POWER SAVE
Set the display to reduce the power automatically.
•
ENABLE: Choose to enable or disable the Tiling
function. If enabled, the display will apply the settings in
{H MONITORS}, {V MONITORS}, {POSITION}, and {FRAME
COMP.}.
POWER SAVE
RGB
ON
ON
NOTE: The Tiling function will be disabled when the [ON/OFF]
VIDEO
button for PIP is pressed.
POWER ON DELAY
EXIT
MENU
:EXIT MENU
:SEL
+-:ADJ
:RETURN
Select the delayed time until the power-on mode is activated
after the power is turned on manually or automatically. This
setting is useful in hiding start-up messages and powering on
the connected devices at different timings.
•
•
{RGB} - Select {ON} to let the display enter DPMS mode
with no signal detected from the HDMI Graphic mode,
HDMI, DVI-D, or VGA inputs after three successive cycles.
The options are: {OFF}, {2 SEC.}, {4 SEC.}, {6 SEC.}, {8
SEC.}, {10 SEC.}, {20 SEC.}, {30 SEC.}, {40 SEC.}, {50 SEC.}.
{VIDEO} - Select {ON} to let the display enter power saving
mode with no signal detected from the HDMI Video mode or
YPbPr inputs after three successive cycles.
CLOSED CAPTION
HEAT STATUS
Choose to display or hide captions.
This function allows you to check the thermal status of the
display at any time.
NOTE: This item is functional for S-VIDEO or VIDEO input
only.
•
•
{OFF} - Captions are hidden.
HEAT STATUS
{CC1} - Captions are displayed in sync with the primary
audio.
COOLING FAN 1
COOLING FAN 2
BRIGHTNESS
OFF
OFF
NORMAL
•
•
•
•
{CC2} - Information (related to the primary audio) is
displayed without sync.
{CC3} - Captions are displayed in sync with the secondary
audio.
TEMPERATURE:
SENSOR 1
SENSOR 2
35.7 C / 96.2 F
30.2 C / 86.3 F
{CC4} - Information (related to the secondary audio) is
displayed without sync.
EXIT
MENU
:RETURN
:EXIT MENU
{TT1 / TT2 / TT3 / TT4} - Four types of information not
related to the displayed images are displayed. (For example,
news and weather forecast.)
NOTE: Check with each supplier of your video software and
external video devices in advance whether they are
compliant with EIA-608-A. If their video signals are
Download from Www.Somanuals.c2om0. All Manuals Search And Download.
SCREEN SAVER
TERMINAL SETTING
Choose to enable the panel saving functions to reduce the risk
of the “image persistence”.
Select the mode to display the HDMI or DVI signal according to
their signal format depending on their source device.
•
{DVI MODE}: Used for DVI-D signal.
SCREEN SAVER
•
Select {DVI-PC} when the source device is a PC.
•
Select {DVI-HD} when the source device is a video
device.
COOLING FAN
BRIGHTNESS
MOTION
AUTO
OFF
OFF
•
{HDMI SIGNAL}: Used for HDMI signal.
•
Select {LIMITED} when displaying the signal that uses
16 to 235 levels of 256 levels for each R, G, and B.
EXIT
MENU
:EXIT MENU
•
Select {FULL} when displaying the signal that uses all
:SEL
+-:ADJ
:RETURN
256 levels (from level 0 to 255).
•
{COOLING FAN} - Select {ON} to turn on the cooling fan
all the time. Select {AUTO} to turn on/off the cooling fan
according to the display’s temperature.
TERMINAL SETTING
NOTES:
DVI-MODE
HDMI SIGNAL
DVI-PC
FULL
•
The default {AUTO} option will start running the cooling
fan if the temperature of 65°C (152°F) is reached, and
will keep running for 30 minutes after cooling down to the
temperature of 62°C (144°F).
1
•
A temperature-warning message will be shown on the
screen once the temperature reaches 79°C. All key
function except [Power] key will then be disabled.
2
3
•
•
{BRIGHTNESS} - Select {ON} and the brightness of
the image will be reduced to an appropriate level, and
the Brightness setting in the Picture menu will become
unavailable.
EXIT
MENU
:EXIT MENU
:SEL
+-:ADJ
:RETURN
{MOTION} - Select the time interval ({10 ~ 900} Seconds /
{OFF}) for the display to slightly expand the image size and
shift the position of pixels in four directions (up, down, left, or
right).
SCAN CONVERSION
Choose to enable or disable the IP (Interlace to Progressive)
conversion function.
SIDE BORDER COLOR
•
{PROGRESSIVE} - Enable the IP conversion function
(recommended). Once enabled, the interlace input signal will
be converted to progressive format for better display quality.
Adjust the brightness of the black areas displayed on both sides
of 4:3 images.
CONFIGURATION3 RESET
•
{INTERLACE} - Disable the IP function. This mode is
suitable for displaying motion pictures, but it increases the
chance of image retention.
Reset all settings in the CONFIGURATION3 menu to factory
preset values.
COLOR SYSTEM
4.2.8. ADVANCED OPTION menu
Selects the Color System depends on your input video format.
The options are: {AUTO} / {NTSC} / {PAL} / {SECAM} /
{4.43NTSC} / {PAL-60}.
ADVANCED OPTION
INPUT CHANGE
NORMAL
NOTE: This item is functional for S-VIDEO or VIDEO input
TERMINAL SETTING
SCAN CONVERSION
COLOR SYSTEM
SCAN MODE
only.
SCAN MODE
SERIAL CONTROL
LAN SETTING
TOUCH PMS
ADVANCED OPTION RESET
FACTORY RESET
LAN
OFF
Change the display area of the image.
1
•
{OVERSCAN} - Display about 95% of the original size of the
image. The rest of the areas surrounding the image will be
cut off.
2
3
•
{UNDERSCAN} - Display the image in its original size.
NOTE: This item is functional for HDMI-Video timing input
only.
SERIAL CONTROL
SET
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
Select the nectwork control port.
The options are: {RS-232C} / {LAN}.
INPUT CHANGE
NOTE: If {LAN} is selected, then {RS-232C} will not be
Select the time for input switching as {NORMAL} or {QUICK}.
activated, even if a cable is attached, and vice versa.
NOTE: The selection {QUICK} may cause a slight noise.
Download from Www.Somanuals.c2om1. All Manuals Search And Download.
LAN SETTING
Assign {IP ADDRESS}, {SUBNET MASK}, and {DEFAULT
GATEWAY} for the display.
LAN SETTING
DHCP CLIENT
OFF
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
1
2
3
EXIT
MENU
:EXIT MENU
:SEL
+-:ADJ
:RETURN
•
DHCP - Choose to enable or disable the DHCP function. If
enabled, the display will be assigned IP address, Subnet
mask and Default gateway automatically. If disabled, you will
be prompted to enter the following value manually. Finally,
press [SET] button to store and save the chosen values.
Touch PMS
Enable and disable wake up from power saving mode by touch
screen.
ADVANCED OPTION RESET
Reset all settings in the ADVANCED OPTION menu to factory
preset values.
1. Press [SET] button to enter the submenu.
2. Press [ ] or [ ] button to select {YES}, and then press
[SET] button to do the reset.
ADVANCED OPTION RESET
NO
YES
SET
EXIT
MENU
:EXIT MENU
:SEL
:SET
:RETURN
FACTORY RESET
Reset all the settings in the OSD menus of {PICTURE},
{SCREEN}, {AUDIO}, {PIP}, {CONFIGURATION1},
{CONFIGURATION2}, {CONFIGURATION3}, and {ADVANCED
OPTION} to factory preset values.
1. Press [SET] button to enter the submenu.
2. Press [ ] or [ ] button to select {YES}, and then press
[SET] button to do the reset.
FACTORY RESET
NO
YES
SET
EXIT
MENU
:EXIT MENU
:SEL
:SET
:RETURN
Download from Www.Somanuals.c2om2. All Manuals Search And Download.
5.
Input Mode
VGA Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
4:3
Stand for Mode
H Pixels
V Lines
480
480
480
400
600
600
768
768
768
800
960
1024
768
768
1200
1080
60 Hz
72 Hz
75 Hz
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
25.175 MHz
31.5 MHz
31.5 MHz
33.75 MHz
40 MHz
VGA
640
Video Graphic Array
WVGA
SVGA
720
800
16:9
4:3
Wide Video Graphic Array
Super VGA
49.5 MHz
65 MHz
XGA
1024
4:3
Extended Graphic Array
78.75 MHz
79.5 MHz
79.5 MHz
108 MHz
108 MHz
85.5 MHz
85.5 MHz
162 MHz
148.5 MHz
WXGA
WXGA
SXGA
1280
1280
1280
1280
1360
1366
1600
1920
5:3
16:10
4:3
Wide XGA
Wide XGA
Super XGA
Super XGA
Wide XGA
Wide XGA
Ultra XGA
HD1080
SXGA
5:4
WXGA
WXGA
UXGA
HD1080
16:9
16:9
4:3
16:9
SDTV Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
H Pixels
V Lines
480i
480p
576i
29.97 Hz
59.94 Hz
25 Hz
13.5 MHz
27 MHz
13.5 MHz
27 MHz
720
480
4:3
4:3
Modified NTSC Standard
Modified PAL Standard
720
480
576p
50 Hz
HDTV Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
74.25 MHz
74.25 MHz
148.5 MHz
Aspect Ratio
16:9
Stand for Mode
H Pixels
V Lines
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
720p
1080i
1080p
1280
720
Normally DVB Mode
Normally ATSC Mode
Normally ATSC Mode
1920
1920
1080
1080
16:9
16:9
•
•
•
•
The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz). CDP3235 is 1366x768, 60Hz mode.
Your PC display screen might appear different depending on the manufacture (and your particular version of Windows).
Check your PC instruction book for information about connecting your PC to a monitor.
If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal
signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the
[INPUT] button to enter the video mode. Also, make sure that the PC is connected.
•
•
•
•
When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
The display settings table complies to the IBM/VESA standards, and based on the analog input.
The DVI support mode is regarded as same to the PC support mode.
The best timing for the vertical frequency to each mode is 60Hz.
Download from Www.Somanuals.c2om3. All Manuals Search And Download.
6.
Cleaning and Troubleshooting
6.1. Cleaning
Caution When Using the Display
•
Do not bring your hands, face or objects close to the
ventilation holes of the display. The top of the display is
usually very hot due to the high temperature of exhaust
air being released through the ventilation holes. Burns or
personal injuries may occur if any body parts are brought
too close. Placing any object near the top of the display
could also result in heat related damage to the object as
well as the display itself.
•
•
Be sure to disconnect all cables before moving the
display. Moving the display with its cables attached may
damage the cables and thus cause fire or electric shock.
Disconnect the power plug from the wall outlet as
a safety precaution before carrying out any type of
cleaning or maintenance procedure.
Front Panel Cleaning Instructions
•
The front of the display has been specially treated. Wipe
the surface gently using only a cleaning cloth or a soft,
lint-free cloth.
•
If the surface becomes dirty, soak a soft, lint-free cloth
in a mild detergent solution. Wring the cloth to remove
excess liquid. Wipe the surface of the display to remove
dirt. Then use a dry cloth of the same type to dry.
•
•
Do not scratch or hit the surface of the panel with fingers
or hard objects of any kind.
Do not use volatile substances such as insert sprays,
solvents and thinners.
Cabinet Cleaning Instructions
•
If the cabinet becomes dirty, wipe the cabinet with a soft,
dry cloth.
•
If the cabinet is extremely dirty, soak a lint-free cloth
in a mild detergent solution. Wring the cloth to remove
as much moisture as possible. Wipe the cabinet. Use
another dry cloth to wipe over until the surface is dry.
•
Do not allow any water or detergent to come into contact
with the surface of the display. If water or moisture gets
inside the unit, operating problems, electrical and shock
hazards may result.
•
•
•
Do not scratch or hit the cabinet with fingers or hard
objects of any kind.
Do not use volatile substances such as insert sprays,
solvents and thinners on the cabinet.
Do not place anything made from rubber or PVC near
the cabinet for any extended periods of time.
Download from Www.Somanuals.c2om4. All Manuals Search And Download.
6.2. Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of
the display is not switched on.
2. Make sure the power switch is switched
on.
3. The selected input has no connection.
4. The display is in standby mode.
3. Connect a signal connection to the
display.
Interference displayed on the display or Caused by surrounding electrical appliances Move the display to another location to see
audible noise is heard
or fluorescent lights.
is the interference is reduced.
Color is abnormal
The signal cable is not connected properly. Make sure that the signal cable is attached
firmly to the back of the display.
Picture is distorted with abnormal
patterns
1. The signal cable is not connected
properly.
1. Make sure that the signal cable is
attached firmly.
2. The input signal is beyond the
capabilities of the display.
2. Check the video signal source to see
if it is beyond the range of the display.
Please verify its specifications with this
display’s specification section.
Display image doesn’t fill up the full size The zoom mode is not correctly set.
of the screen
Use the Zoom mode or Custom zoom
function in the Screen menu to fine tune
display geometry and time frequency
parameter.
Can hear sound, but no picture
Improperly connected source signal cable. Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal
cable.
1. Make sure that both video inputs and
sound inputs are correctly connected.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
2. Press [VOL UP] or [VOL DOWN] button
to hear sound.
3. Switch MUTE off by using the [MUTE]
4. No external speaker connected.
button.
4. Connect external speakers and adjust
the volume to a suitable level.
Some picture elements do not light
up
Some pixels of the display may not turn on. This display is manufactured using an
extremely high level of precision technology:
however, sometimes some pixels of the
display may not display. This is not a
malfunction.
After-Images can still be seen on the
A still picture is displayed for an over
Do not allow a still image to be displayed
for an extended period of time as this can
cause a permanent after-image to remain
on the display.
display after the display is powered off. extended period of time
(Examples of still pictures include logos,
video games, computer images, and
images displayed in 4:3 normal mode)
Download from Www.Somanuals.c2om5. All Manuals Search And Download.
7.
Technical Specifications
CDP3235
Display:
Item
Specifications
Screen Size (Active Area)
Aspect ratio
80.1cm/32”(31.5” viewable) Diagonal, 697.689mm(H), 392.256mm(V)
16:9
Number of pixels
1366 (H) x 768 (V)
Pixel pitch
0.51075 (H) x 0.51075 (V) [mm]
16.7M colors
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
450 cd/m2
3000:1
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB: TMDS (Video + Audio)
(Type A) (18 pin)
MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel
(L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB: TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
Video Input
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
BNC Jack x 1
Composite 1V [p-p] (75Ω)
General:
Item
Specifications
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
160W
Power Consumption (Max)
Power Consumption (typ.)
140W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<1W (RS232 in active)
773.6 x 505.1 x 239.8 mm
773.6 x 468.3 x 116 mm
14.19kg
Weight (Without Stand)
12.93kg
Download from Www.Somanuals.c2om6. All Manuals Search And Download.
Gross Weight
16.5kg
VESA Wall mount
400x200mm,200x200, M6
Environmental Condition:
Item
Specifications
Temperature
Humidity
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Altitude
Operational
Storage / Shipment
0 ~ 9,000 m
Internal Speaker:
Item
Specifications
10W+10W (RMS)
8Ω
Output
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
Download from Www.Somanuals.c2om7. All Manuals Search And Download.
CDP4235/CDP4235-T
Display:
Item
Specifications
Screen Size (Active Area)
Aspect ratio
42” LCD 106.7cm/42” Diagonal, 930.24mm(H), 523.26mm(V)
16:9
Backlight
CCFL
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.4845 (H) x 0.4845 (V) [mm]
16.7M colors
450 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
4000:1
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB: TMDS (Video + Audio)
(Type A) (18 pin)
MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel
(L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB: TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
Video Input
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
BNC Jack x 1
OPS
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
External slot
Composite 1V [p-p] (75Ω)
Expansion slot adapter fr Open Pluggable Specification(OPS) card
General:
Specifications
Item
CDP4235
CDP4235-T
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
260W
Power Consumption (Max)
Power Consumption (typ.)
210W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<1W (RS232 in active)
991.6 x 621 x 329.8 mm
991.6 x 584 x 115.5 mm
22.96 Kg
991.6 x 621 x 329.8 mm
991.6 x 584 x 128 mm
29.6 Kg
Weight (Without Stand)
21.36 Kg
28 Kg
Download from Www.Somanuals.c2om8. All Manuals Search And Download.
VESA Wall mount
Gross Weight
400x200mm,200x200, M6
27.5 Kg
26.8 Kg
Environmental Condition:
Item
Specifications
Temperature
Humidity
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Altitude
Operational
Internal Speaker:
Item
Specifications
10W+10W(RMS)
8Ω
Output
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
CDP4235-T Touch specification
Touch Panel
Detection Method
Optical touch, 4-cam sensor
4-touch full screen
0.5mm(typ.)
Number of Touch
Touch Accuracy
Detection Resolution 1012 pixels
PC connector
Protective
USB type B
4mm tempered glass
Download from Www.Somanuals.c2om9. All Manuals Search And Download.
CDP4635/CDP4635-T
Display:
Item
Specifications
Screen Size (Active Area)
Aspect ratio
116.8cm/46” Diagonal , 1018.08mm(H), 572.67mm(V)
16:9
Backlight
CCFL
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.53025 (H) x 0.53025 (V) [mm]
16.7M colors
400 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
4000:1
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB: TMDS (Video + Audio)
(Type A) (18 pin)
MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel
(L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB: TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
Video Input
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
BNC Jack x 1
OPS
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
External slot
Composite 1V [p-p] (75Ω)
Expansion slot adapter fr Open Pluggable Specification(OPS) card
General:
Specifications
Item
CDP4635
CDP4635-T
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
270W
Power Consumption (Max)
Power Consumption (typ.)
220W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<1W (RS232 in active)
1091.1 x 681.7 x 329.8 mm
1091.1 x 645.7 x 120.1 mm
26.3 Kg
1091.1 x 681.7 x 329.8 mm
1091.1 x 645.7 x 133.1 mm
32.2 kg
Weight (Without Stand)
24.6 Kg
31.6 kg
Download from Www.Somanuals.c3om0. All Manuals Search And Download.
VESA Wall mount
Gross Weight
400x400mm,400x200mm, M6
31 Kg
Environmental Condition:
Item
Specifications
Temperature
Humidity
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Altitude
Operational
Internal Speaker:
Item
Specifications
10W+10W(RMS)
8Ω
Output
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
CDP4635-T touch specification
Touch Panel
Detection Method
Optical touch, 4-cam sensor
4-touch full screen
0.6mm(typ.)
Number of Touch
Touch Accuracy
Detection Resolution 1012 pixels
PC connector
Protective
USB type B
4mm tempered glass
Download from Www.Somanuals.c3om1. All Manuals Search And Download.
CDX5550-L
Display:
Item
Specifications
Screen Size (Active Area)
Aspect ratio
138.68cm/55”(54.6” Viewable) Diagonal, 1209.6mm(H), 680.4mm(V)
16:9
Backlight
Direct LED
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.63 (H) x 0.63 (V) [mm]
16.7M colors
700 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
3500:1
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB: TMDS (Video + Audio)
(Type A) (18 pin)
MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel
(L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB: TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
Video Input
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
BNC Jack x 1
OPS
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
External slot
Composite 1V [p-p] (75Ω)
Expansion slot adapter for Open Pluggable Specification(OPS) card
General:
Item
Specifications
AC 100 ~ 240V, 50 ~ 60Hz
360W
Power Supply
Power Consumption (Max)
Power Consumption (typ.)
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
190W
<1W (RS232 in active)
1215.3 x 737.8 x 400 mm
1215.3 x 686.1 x 128.1 mm
38.2 Kg
Weight (Without Stand)
36 Kg
Gross Weight
43 Kg
VESA Wall mount
400x400mm, M6
Download from Www.Somanuals.c3om2. All Manuals Search And Download.
Environmental Condition:
Item
Specifications
Temperature
Humidity
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Altitude
Operational
Internal Speaker:
Item
Specifications
10W+10W(RMS)
8Ω
Output
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
Download from Www.Somanuals.c3om3. All Manuals Search And Download.
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
T = Telephone
F = FAX
Country/Region
Website
Email
Australia/New
Zealand
AUS= 1800 880 818
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Canada
Europe
Hong Kong
India
T= 852 3102 2900
T= 1800 266 0101
uk/
uk/support/call-desk/
service_ie@viewsoniceurope.
com
Ireland (Eire)
Korea
T= 080 333 2131
T= 0800-4441185
T= 1230-020-7975
T= 01800-9-157235
T= 001-8882328722
Latin America
(Argentina)
Latin America
(Columbia)
Latin America
(Mexico)
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
T= 0800-54565
Macau
ap.viewsonic.com/me/
T= 853 2870 0303
Contact your reseller
Middle East
T= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= 1-909-468-3757
Puerto Rico & Virgin
Islands
Singapore/Malaysia/
Thailand
ap.viewsonic.com/za/
T= 65 6461 6044
South Africa
Contact your reseller
uk/
uk/support/call-desk/
service_gb@viewsoniceurope.
com
United Kingdom
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-3757
United States
Download from Www.Somanuals.c3om4. All Manuals Search And Download.
Limited Warranty
VIEWSONIC® LCD Commercial Display
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during
the warranty period. If a product proves to be defective in material or workmanship during the warranty period,
ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts
may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic LCD Commercial Displays are warranted for 3 years for all parts excluding the light source and 3 years
for labor from the date of the first customer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic’s specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to
Customer Support page). You will need to provide your product’s serial number.
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or
ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Download from Www.Somanuals.c3om5. All Manuals Search And Download.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of
use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with
business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Some states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or
consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact
ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to
the terms and conditions of the Maintenance Guarantee Card.
under Support/Warranty Information.
4.3: ViewSonic LCD Commercial Display
CD_LW01 Rev. 1a 02-11-09
Download from Www.Somanuals.c3om6. All Manuals Search And Download.
Mexico Limited Warranty
VIEWSONIC® LCD Commercial Display
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a
product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace
the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic LCD Commercial Displays are warranted for 3 years for all parts excluding the light source and 3 years for labor from the date
of the first customer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow
instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic’s specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product
for an extended period of time.
4. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer
Support page). You will need to provide your product’s serial number, so please record the product information in the space provided
below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________
Document Number: _____________________
Purchase Date: ________________________
Model Number: _____________________________
Serial Number: _____________________________
Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? ___________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a
description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of
merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss
of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss,
even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Download from Www.Somanuals.c3om7. All Manuals Search And Download.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Villahermosa:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: [email protected]
E-Mail: [email protected]
Puebla, Pue. (Matriz):
Veracruz, Ver.:
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: [email protected]
Tel: 01-22-91-00-31-67
E-Mail: [email protected]
Chihuahua
Cuernavaca
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: [email protected]
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: [email protected]
Distrito Federal:
Guadalajara, Jal.:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : [email protected]
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: [email protected]
Guerrero Acapulco
Monterrey:
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: [email protected]
MERIDA:
Oaxaca, Oax.:
ELECTROSER
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: [email protected]
Fax: 01(52)95-15-13-67-00
E-Mail. [email protected]
Tijuana:
FOR USA SUPPORT:
STD
ViewSonic Corporation
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
4.3: ViewSonic Mexico Limited Warranty
CD_LW02 Rev. 1A 06-25-07
Download from Www.Somanuals.c3om8. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|