ADDISON
Freestanding
Electric
Stove Models:
ACSB
ACSG
ACSM
Installation Instructions and Homeowner's Manual
WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY
DO NOT STORE
®
OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS OR LIQUIDS
IN THE VICINITY OF THIS OR ANY
C
US
OTHER APPLIANCE.
The Vermont Castings
Majestic Products Company
410 Admiral Blvd. • Mississauga, Ontario, Canada. L5T2N6 • 905-670-7777
10003646
11/01 Rev. 1
INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
INSTALLATION INSTRUCTIONS
GENERAL
1.
2.
Read all instructions before using this appliance.
14. Do not insert or allow foreign objects to enter
any ventilation or exhaust opening as this may
cause an electric shock, fire, or damage the
appliance.
This appliance is hot when in use. To avoid
burns, do not let bare skin touch hot surfaces. If
provided, use handles when moving this
appliance. Keep combustible materials,such as
furniture, pillows, bedding, papers, clothes, and
curtains at least 3 feet (1 m.) from the front of
this appliance.
15. To prevent possible fire, do not block air intakes
or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may
become blocked.
3.
CAUTION: Extreme caution is necessary
when any heater is used by or near children
or invalids and whenever the heater is left
operating unattended.
16. This appliance has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint, or flammble liquids are used or
stored. This fireplace should not be used as a
drying rack for clothing, nor should Christmas
stockings or decorations be hung on or near it.
4.
5.
If possible, always unplug this appliance when
not in use.
17. Use this appliance only as described in this
manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or
injury to persons.
Do not operate any heater with a damaged cord
or plug or after the appliance malfunctions, has
been dropped or damaged in any manner.
6.
7.
Any repairs to this fireplace should be carried
out by a qualified service person.
18. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk
of fire. However, if you have to use an extension
cord, the cord shall be No. 16 AWG minimum
size and rated not less than 1900 Watts. The
extension cord must be a three wire cord with
grounding type plug and cord connector.
Under no circumstances should this fireplace be
modified. Parts having to be removed for
servicing must be replaced prior to operating
this fireplace again.
8.
9.
Do not use outdoors.
19. SAVE THESE INSTRUCTIONS.
This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate this appliance where it may fall into a
bathtub or other water container.
10. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or the like.
Arrange cord away from traffic areas and where
it will not be tripped over.
LOCATING YOUR FIREPLACE
11. To disconnect this appliance, turn controls to
the off position, then remove plug from outlet.
Your new freestanding electric fireplace may be
installed virtually anywhere in your home. However,
when choosing a location for your new fireplace,
ensure that the general instructions are followed.
Also, for best effect, install the fireplace out of direct
sunlight.
12. Connect to properly grounded outlets only.
13. This appliance, when installed must be
electrically grounded in accordance with local
codes, with the current CSA C22.1 Canadian
Electrical codes or for USA installations, follow
local codes and the National Electrical Code,
ANSI/NFPA NO. 70.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
FIREPLACE DIMENSIONS
E
A
F
C
B
D
A
B
C
D
E
F
Width of Stove Top
Width at Legs
565 mm
22-1/4 in
600 mm
390 mm
430 mm
400 mm
635 mm
23-3/8 in
15-3/8 in
17 in
Depth at Legs
Depth at Apron
Depth at Stove Top
Total Height
15-3/4 in
25 in
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
ELECTRICAL CONNECTION
CLEARANCE TO COMBUSTIBLES
A 15 AMP, 120 Volt, 60 Hz circuit with a properly
grounded outlet is required. Preferably, the fireplace
will be on a dedicated circuit as other appliances on
the same circuit may cause the circuit breaker to trip or
the fuse to blow when the heater is in operation.
The unit comes standard with a 6’ (1828 mm) long
three wire cord, exiting from the rear of the fireplace.
Plan the installation to avoid the use of an extension
cord. If an extention cord must be used, it must be a
minumum 16AWG, three wire with grounding type plug
connector and rated not less than 1900 Watts.
Back...........................0”/0 mm
Sides..........................0”/0 mm
Floor...........................0”/0 mm
Top...........................12”/305 mm
HEARTH
WARNING: Electrical outlet wiring must
comply with local building codes and
other applicable regulations to reduce
the risk of fire, electrical shock and
injury to persons.
A hearth is not mandatory but it is recommended for
aesthetic purposes. We recommend a non-combustible
hearth which does not obstruct heater openings.
ELECTRICAL SPECIFICATIONS
WARNING: Do not use this fireplace if
any part of it has been under water.
Immediately call a qualified service
technician to inspect the fireplace and
replace any part of the electrical system.
Voltage..........................120VAC/60Hz
Total Amps....................11.9 Amps
Total Watts....................1430 Watts
Heater Ratings..............1300 Watts
WARNING: This fireplace comes with an
optional manual circuit breaker reset near
the power cord supply. In case the
fireplace is not operating check the circuit
breaker and reset the button at the
breaker. If the fireplace is still not
operating immediately call a qualified
service technician to inspect the fireplace.
LAVA ROCK MATERIAL PLACEMENT
A bag of decorative lava rock is included with this unit.
To place the lava rock in the stove, follow the direc-
tions for removing the firebox (page 6, step 1 through
7). Spread lava rock evenly on exposed area of the
orange ember bed.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
SERVICE INSTRUCTIONS
WARNING: Disconnect power before
attempting any maintenance or cleaning
to reduce the risk of fire, electrical
shock or personal injury
REPLACING LIGHT BULBS
This fireplace uses two clear 120 Volt, 60 Watt, E-12
socket base light bulbs (small base, chandelier candle
type). The 60 Watt bulbs are located under the log set/
ember bed. For convenience, if one of the bulbs burns
out, it may be a good idea to replace both of the light
bulbs.
FIREBOX REMOVAL
1. Unplug the electrical supply to the unit.
2. Let the fireplace cool if it has been operating.
3. Move the fireplace away from wall to gain access
to the rear of the unit.
4. Locate the firebox mounting brackets on the side of
the firebox. Remove the screws securing the firebox
to the mounting brackets. (Figure 1).
5. Remove firebox by sliding it rearward out of
the casing.
6. Gently place firebox on its back on the floor.
7. To reinstall firebox, follow the above procedure
in reverse.
1. Turn off power to the unit by unplugging the
power cord.
2. Let fireplace cool if it has if it has been operating.
3. Remove firebox from casing. (See Firebox removal)
4. Remove the two screws securing the ember bed
and log set in position. One screw is located on
either side of the ember bed near the front.
5. Examine the bulbs to determine which bulbs need
to be replaced.
6. While holding the socket, unscrew defective bulb(s).
7. Install the new light bulb(s) by screwing in while
holding the socket.
8. Reinstall ember bed and log set.
9. Reinstall firebox.
WARNING: Do not exceed 60 watts per
bulb for lights beneath the ember bed.
Use of higher rated bulbs may result in a
fire, causing property damage or
personal injury.
Mounting
Brackets
(2 per side)
MAINTENANCE OF MOTORS
Figure 1: Side view of the firepla
showing the firebox mounting br
The motors used on the fan and the flame generator
assembly are prelubricated for extended bearing life and
require no further lubrication. However, periodic cleaning/
vacuuming of the fan/heater unit is recommended.
GLASS INFORMATION
1. Under no circumstances should this product be
operated with missing or broken glass.
2. Do not strike or slam the glass.
3. Do not use abrasive cleaners to clean the glass.
4. This product uses tempered glass. Replacement
glass (with gasket) is available from the
WARNING: Make sure that the power is
turned off before proceeding.
manufacturer and replacement should be carried
out by a qualified service person.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
ELECTRICAL WIRING DIAGRAM
Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national
and local codes.
If repairing or replacing any electricial component or wiring, the original wire routing, color coding
and securing locations must be followed.
6 BLACK
1
3
2
SWITCH
BLACK
FLAME
MOTOR
5
6
6
2 BLACK
7
7
60 WATT
60 WATT
5 BLACK
8
7 WHITE
8
1. 120v Motor AC
2. Rocker Switch
3. Thermostat
7
WHITE
BLACK
FAN
MOTOR
WHITE
BLACK
1 WHITE
4. Fan/Heater
5. Light Socket w/ Wiring Assy (2 Lamp)
6. Light Bulb 60 W
7. Nylon Cable Tie 6 -1/8 Black
8. Busing Snap Hole
3 RED
4
4 BROWN
9. Busing Strain Relief
10. Power Cord
11. CFM-Majestic Factory Wire
12. Breaker Circuit Manual Reset
9
HEATER
ELEMENT
BREAKER CIRCUIT
(OPTIONAL)
12
10
BOMAX FAN/HEATER WIRING DIAGRAM
7 WHITE
FAN
MOTOR
1 WHITE
3 RED
WHITE
HEATER
ELEMENT
WHITE
OPERATING INSTRUCTIONS
MAIN ON/OFF SWITCH
HEATER CONTROL
The Heater Control acts to turn the
heater on and off as well as setting the
comfort level in the room. Turning the
knob clockwise from the off position
will place the heater into operation.
The further the knob is rotated
clockwise, the higher the set point
temperature. Turning the knob
counterclockwise will lower the set
point temperature. Turning it all the
way counterclockwise will turn the
heater function off.
The On/Off switch supplies power to
Temperature
Control
ON/OFF
Switch
all of the functions of the fireplace. It
is located on the top of the firebox at
the rear of the unit.
WARNING: During any service of
this appliance, the power to the
unit must be turned off. It is not
acceptable to use the “On/Off”
switch to meet this requirement.
Figure 2:
Control locations at
the top rear corner of
the fireplace.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
REPLACEMENT PARTS LIST
Item #
Part Description
Part Number
1
2
3
4
5
6
7
8
Log Set
Fan/Heater Asembly
10003645
10002175
10003587
10003095
10001393
10001971
10001639
0003442
Flame Generator Motor-120 Volt AC w/Terminal
Cord Power 16/3 HPN w/Terminals
ON/OFF Switch
Heater Control (Thermostat)
Heater Control Knob
Door Glass, with gasket (not shown)
Flame Generator Assembly
Light filter (Ember Bed) (not shown)
Light Diffuser (rear screen) (not shown)
Tinted Screen (not shown)
Light Bulb Socket w/Wiring Assembly
Front - Addison
End, Right/Left - Addison
Leg - Addison
Top - Addison
Glass - Addison
Gasket, 3/4” Flat Window - Blk
Mounting Bracket
Front - Addison - Mdnt
End, Right/Left - Addison - Mdnt
Leg - Addison - Mdnt
Top - Addison - Mdnt
Front - Addison - Fgrn
End, Right/Left - Addison - Fgrn
Leg - Addison - Fgrn
Top - Addison - Fgrn
9
10003566
10002159
10002150
10002151
10003568
30000621
30000622
30000623
30000624
30000664
30000776
10003524
30000787
30000788
30000789
30000790
30000791
30000792
30000793
30000794
10003093
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Breaker Circuit Manual Reset
17
24
28
5
4
15
22
26
15
22
26
18
20
7
2
19
14
21
25
13
6
16
23
27
3
1
9
29
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The Verm ont Castings Majestic Products Com pany
DOOR GLASS REPLACEMENT INSTRUCTIONS
1. Unplug the electrical supply to the unit.
Door Glass Replacement Parts
Glass - Addison
2. Let the fireplace cool if it has been operating.
30000664
30000776
1601396
1600660
1601981
3. Move the fireplace away from the wall to gain access
to the rear of the unit.
Gasket, 3/4” Flat Window-Blk
Clip
4. Locate the firebox mounting brackets on the side of
the firebox. Remove the screws securing the firebox to
the mounting brackets (Figure 1).
Knob, Therm-Maple
Stub, Control Door
5. Remove firebox by sliding it rearward out of the casing.
6. Gently place firebox on its back on the floor.
7. Locate the glass clips on the inside surface of the
front casting. Remove the glass, and clear the area of
any glass fragments (Figure 3).
8. Secure new glass (with gasket) to the inside surface of
the front casting, reversing the process above, making
sure the glass is placed with gasket covering the bottom
and sides of the glass. (Figure 3).
9. Reinstall firebox into casing, by reversing steps 1
through 6.
Glass
Glass
Clips
Gasket
Figure 3: Door assembly
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|