INTRUDUCTION
Parts Check List:
To purchase replacement battery packs, call
VTECH Communications at 1-800-595-9511.
In Canada, call VTECH Electronics at 1-800-
267-7377.
1.
2.
3.
4.
5.
Handset
Base Unit
Telephone line cord
Battery Pack
AC adapter
1
REPLACINGTHE HANDSET BATTERIES
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
1. Slide the battery cover off by gently pressing
on the recessed area with a downward motion.
2. Unplug and remove the old battery pack. Don't
put the old battery pack in a trash compactor
or a fire - it could burst.
3. Plug in the replacement battery pack. Place
the battery pack in the compartment with the
battery cord resting on top of it.
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these
openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. This product should not be placed in a built-in-installation where
proper ventilation is not provided.
4. Replace the battery cover by sliding it into
place.
5. The new battery pack must be charged before
using your telephone. Place the handset in the
cradle of the base unit to allow it to charge for
16 hours. Maximum battery life between
charges is more than 5 hours of continuous
talk time or 6 days of standby.
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking
on it.
9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short
out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
10.To reduce the risk of electric shock, do not disassemble this product. If service or repair work is required, contact VTech
Customer Service at 1-800-595-9511. Opening or removing cabinet parts other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently
used.
CAUTION: To reduce the risk of fire or injury, read
and follow these instructions:
1. Use only VTECH battery (80-5074-00-00).
2. Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
3. Exercise care in handling batteries in order not to short the battery with conducting materials such as
rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
4. Do not dispose of the battery in a fire.The cell may explode.
11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
12.Unplug this product from the wall outlet:
a) When the power supply cord or plug is damaged or frayed.
b) If liquid has been spilled into the product.
The RBRC™ Seal
c) If the product has been exposed to rain or water.
The RBRC® Seal on the nickel-cadmium battery indicates thatVTech Communications, Inc.is
voluntarily participating in an industry program to collect and recycle these batteries at the end
of their useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-cadmium batteries
into the trash or municipal waste, which may be illegal in your area.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustment of other controls may result in damage and will often require
extensive work to restore the product to normal operation.
e) If the product has been dropped and the cabinet has been damaged.
f) If the product exhibits a distinct change in performance.
VTech’s participation with RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorizedVTech product service centers. Please call 1-800-8-
BATTERY™ for information on Ni-Cd battery recycling and disposal bans / restrictions in your area.VTech’s
involvement in this program is part of its commitment to protecting our environment and conserving
natural resources.
13.Avoid using a telephone (other than a cordless type) during an electrical storm.There may be a remote risk of electric shock
from lighting.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVETHESE INSTRUCTIONS
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
3
2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
TONE/PULSE Setting
Turning OffThe Ringer
To turn off the ringer on the handset, do the
following:
If you have touch tone service on phone line.
Press PROG, * , *, MEM to switch to TONE
dialing. If you have rotary service, press
PROG, * , # ,MEM to switch to PULSE.
NOTE: Your VT9119 is preset at the factory
for TONE dialing.
•
•
•
•
•
Press PROG
Press the # key
Press 5 to turn off the ringer
Press the MEM key to confirm
To turn the ringer on again, see
Programming the Ringer Type.
TemporaryTone
If you have a rotary (dial-pulse) telephone
service, (TONE/PULSE setting is set to
PULSE), this feature allows you to enter
special codes and tones to operate answering
machines, use electronic banking services,
calling cards, or other special services.
First, dial the call normally. Then activate the
Temporary Tone feature by pressing TONE
(the * key). You can then press the numbers
or symbols you need, and your phone will send
the proper signals.
CheckingThe Ringer
To check the ringer which is currently
programmed, do the following:
•
•
•
•
Press PROG
Press the # key
Press 0
Press the MEM key to confirm
Making Calls
To answer a call when the handset is in the
base, just pick up the handset.
Pick up the handset and press PHONE.When
you hear a dial tone, dial the number. The
PHONE LED will illuminate while the Handset
is in use.
If you make a mistake when dialing, press OFF
to hang up, then press PHONE to get the dial
tone again.
Memory Dialing
The VT9119 can store up to 10 different phone
numbers that you can dial just by pressing
phone, MEM and one of the number keys (0-
9).
To answer a call when the handset is away
from the base, just press any key on the
handset (except OFF). This is very useful in a
dark environment; you do not have to fumble
around looking for the PHONE key to answer
the call.
To end the call, press OFF or place the handset
back in the base.The phone will automatically
go back to rotary (dial-pulse) service.
ProgrammingThe RingerType
Programming Speed Dial Numbers
The handset must be OFF.
1. Press PROG.The PHONE LED will blink to
indicate that you are in the programming
mode.
2. Press the number of the memory location
you wish to store the number in (0-9).
3. Using the dial pad, dial the number you
want to store.The number can be up to 16
digits long. The number can be entered
manually or by using REDIAL.
The handset ringer is capable of four different
types of ringing tones. The following sections
detail how to change the different tones and
to turn off a ringer on the handset.
To program, the handset must be OFF.
To select a different ringer type do the
following:
You must always press PHONE before you can
dial a call on the handset.
Disconnecting
To end a call, either place the handset back in
the base, or press OFF on the handset.
Answering Calls
When an incoming call is ringing, the IN USE
LED on the base and PHONE LED on the
handset will flash. To make sure your phone
rings when the handset is away from the base,
please keep the base antenna in the upright
position.
Changing Channels
If you notice interference when using your
handset, press CHAN to switch to a clear
channel. This function is only available when
you are on a call.
•
•
•
•
Press PROG
Press the # key.
Press a key 1..4 to select a ringer type.
Press the MEM key to confirm.
8
9
OPERATING INSTRUCTIONS
IN CASE OF DIFFICULTY
If you have difficulty operating your phone, the
suggestions below should solve the problem. If you
still have difficulty after trying these suggestions,
In the US Call:
VTECH Communications at
1-800-595-9511.
In Canada Call:
VTECH Electronics at
1-800-267-7377.
THE PHONE DOESN'T WORK AT ALL.
•
Make sure the telephone line cord is plugged firmly
into the base unit and the telephone jack. Make
sure the power cord is plugged in.
4. Press MEM to store the phone number to
the key you selected.
The phone now exits PROG mode and emits
a tone.
1. Press PROG
2. Press 8
3. Press 9
4. Press REDIAL / PAUSE
5. Dial 555-1234
6. Press MEM
•
•
You may be too far from the base unit.
You may have too many extension phones on your
telephone line to allow all of them to ring. Try
unplugging some of the other phones.
Speed Number Dialing
YOUR CALLER FADES IN AND OUT.
You may be nearly out of range. Move closer, or relocate
the base.
YOU HEAR OTHER CALLS WHILE USING YOUR
PHONE.
1. Press PHONE to get a dial tone.
2. Press MEM and the memory location
number key (0-9).
For example, to dial the number you assigned
to key '8', you would press PHONE, MEM, 8.
Using REDIAL
•
•
Make sure the power cord is plugged in.
To REDIAL the last number you called, press
PHONE then press REDIAL. The phone will
automatically dial the number.
Make sure the telephone line cord is plugged firmly
into the base unit and the telephone wall jack.
Make sure the batteries are properly charged. If
the handset makes two beeps, the batteries need
charging. If the IN USE indicators do not light when
you press PHONE, you must charge the batteries.
If you recently installed a new battery pack, make
sure it is installed correctly.
•
Replace the handset in the base cradle, wait a
few moments and try again.
•
•
Disconnect your base unit from the telephone jack,
and plug in a regular telephone. If you still hear
other calls, the problem is probably in your wiring
or local service. Call your local telephone
company.
To Change or Replace a Speed Dial
Number
To change or replace a stored number in
speed dial memory simply enter the new
number and store it in the memory location
you wish to change.
For example, to change the number stored in
memory position 7 to 555-1111, you would
press PROG, 7, 555-1111, MEM.
Storing a Redial Number into Speed Dial
To store the last number you dialed as a Speed
Dial number, press PROG, a location number
(0-9), REDIAL, MEM.
•
NO DIAL TONE.
YOU HEAR NOISE IN THE HANDSET, AND NONE
OF THE KEYS OR BUTTONS WORK.
•
•
•
•
First check all the suggestions above.
If you still don't hear a dial tone, disconnect the
base unit from the telephone jack and connect a
different phone. If there is no dial tone on that
phone either, the problem is in your wiring or local
service. Call your local telephone company.
Make sure the power cord is plugged in.
Your base unit and handset may not be operating
on the same channel or security code. Place the
handset in the cradle for a few moments to reload
the security code and reset the channel.
The Page Feature
From the base unit, press PAGE to signal the
person at the handset. To end the page at the
base, press PAGE again. To end the page at
the handset, press OFF.
If the Handset is in use ( off hock) when PAGE
is pressed on the Base Unit, the Handset will
emit one page alert. If the Handset is not in
use (on hook), the page alert will continue for
approximately 60 seconds.
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
EVEN WHEN YOU'RE NEAR THE BASE UNIT.
Household appliances plugged into the same circuit
as the base unit can sometimes cause interference.
Try moving the appliance or the base unit to another
outlet.
COMMON CURE FOR ELECTRONIC EQUIPMENT
Electronics, like people, can sometimes get confused.
If the unit does not seem to be responding normally,
then try putting the handset in the cradle to re-initialize
the unit. If it still does not seem to respond, perform
the following steps (in the order listed):
1. Disconnect the power to the Base.
2. Disconnect the Handset battery pack.
3. Wait a few minutes.
4. Connect power to the Base.
Storing Pauses in Memory
To insert a pause in a phone number, press
PAUSE.The pause is 2 seconds in length. For
longer pauses, press PAUSE two or more
times. Each additional press indicates an
additional 2 second pause.
If your phone is connected to a PBX you can
store the PBX access number and a pause
before the phone number. For example, to
store 9-PAUSE-555-1234 in memory location
8 do the following:
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
WHEN YOU'RE AWAY FROM THE BASE UNIT.
•
You may be out of range. Either move closer to the
base, or relocate the base unit.
This feature is useful in locating a
misplaced Handset.
•
The layout of your home may be limiting the range.
Try moving the base unit to the second or third
floor, or to some other location.
5. Reconnect the Handset battery.
6. Place the handset in the Base unit cradle. If the
Handset has not been recently charged, allow 8
hours before use.
THE HANDSET DOES NOT RING WHEN YOU
RECEIVE A CALL.
•
Ensure that the ringer is turned on.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL
SPECIFICATIONS
WARRANTY STATEMENT
MAINTENANCE
WHAT DOES OURWARRANTY COVER?
FREQUENCY CONTROL
Crystal Controlled Dual PLL Synthesizer
TAKING CARE OFYOURTELEPHONE
.
•
Any defect in material or workmanship.
FOR HOW LONG AFTERTHE ORIGINAL PURCHASE?
One Year.
WHAT WILL VTECH DO?
At our option, repair or replace your unit.
HOW DO I SEND MY UNIT, IN OR OUT OFWARRANTY?
Your VT9119 cordless telephone contains
sophisticated electronic parts so it must be
treated with care.
TRANSMIT FREQUENCY
Handset: 923.10 MHz to 927.75 MHz
•
Base:
902.3 MHz to 906.65 MHz
•
Avoid rough treatment
RECEIVE FREQUENCY
Handset: 902.3 MHz to 906.65 MHz
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
•
•
Call VTECH Electronics customer service for Return Authorization at: 1-800-595-9511
Properly pack your unit. Include any cables & accessories which were originally provided with
the product. We recommend using the original carton and packing materials.
Include in the package a copy of the sales receipt or other evidence of date of original purchase
(if the unit was purchased within the last twelve months.)
Print your name and address, along with a description of the defect, and include this in the
package.
Include payment for any service or repair not covered by the warranty, as determined by
VTECH Communications.
In the US, ship the unit via UPS Insured, or equivalent to:
San Antonio Returns Center
Base:
923.10 MHz to 927.75 MHz
•
•
•
•
NOMINAL EFFECTIVE RANGE
Avoid Water
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Your telephone can be damaged if it gets wet.
Do not use the handset outdoors in the rain,
or handle it with wet hands. Do not install your
base unit near a sink, bathtub or shower.
Remember that electrical appliances can
cause serious injury if used when you are wet
or standing in water. If your base unit should
fall into water, DO NOT RETRIEVE IT UNTILYOU
UNPLUGTHE POWER CORD ANDTELEPHONE
LINE CORDS FROMTHEWALL. Then pull the
unit out by the unplugged cords.
SIZE
Handset: 17.5cm x 5.5cm x 3.9cm
(L x W xT) maximum
(antenna excluded)
1145 Coliseum Road
Department Vtech
San Antonio, TX 78219
Base:
19.3cm x 14.8cm x 5.4cm
(L x W x T) maximum
(antenna excluded)
VTECH Communications assumes no responsibility for units sent without prior Return Authorization.
WHAT DOES OURWARRANTY NOT COVER?
•
•
•
•
•
Batteries
WEIGHT
Handset: 146 grams
Base: 283 grams
Damage from misuse, neglect, or acts of nature (lightning, floods, power surges. etc.)
Products which may have been modified or incorporated into other products
Products purchased outside the USA
Products serviced by the owner or a service facility not expressly authorized by VTECH
Communications
Electrical Storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment.
For your own safety, use caution when using
electric appliances during storms.
POWER REQUIREMENTS
Handset: Self-contained
nickel-
•
Products purchased more than 12 months from current date
cadmium
rechargeable
HOW DOES STATE LAW RELATETOTHISWARRANTY?
battery supply, 3.6V nominal,
400mAh capacity.
•
This warranty gives you specific rights.You may also have other rights which vary from state to
state.
Cleaning your telephone
Power Adapter: 9V DC @ 200mA
Your telephone has a durable plastic casing
that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened
with water or a mild soap. Do not use excess
water or cleaning solvents of any kind.
IFYOU PURCHASEDYOURTELEPHONE IN CANADA
Please call:
Ship to:
1-800-267-7377 for return authorization.
VTECH ELECTRONICS LTD.
SPECIFICATIONS ARETYPICAL AND
MAY CHANGE WITHOUT NOTICE.
200-7671 ALDERBRIDGE WAY
RICHMOND, BC V6X 1Z9
12
13
FCC AND IC REGULATIONS
This equipment complies with FCC AND IC REGULATIONS 15 and 68 of
the Federal Communications Commission (FCC) rules for the United
States. It also complies with regulations RSS-210 and CS-03 of Industry
Canada (IC).
The REN is useful in determining the number of devices you may
connect to your telephone line and still enable the devices to ring when
you receive a call. The general rule is that the REN value should not
exceed 5.0 total; however, contact your local telephone company for
the specific number in your area.
A label is located on the underside of the base unit containing either
the FCC registration number and Ringer Equivalence Number (REN) or
the IC registration number and Load Number.You must, upon request,
provide this information to your local telephone company.
This equipment is compatible with inductively coupled hearing aids.
IC (Industry Canada)
This telephone is registered for use in Canada.
Notice: The Industry Canada label identifies certified
equipment. This certification means that the equipment
meets certain telecommunications network, protective,
operational and safety requirements. Industry Canada
does not guarantee the equipment will operate to the
user’s satisfaction.
FCC Part 15
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the
FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one
or more of the following measures:
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company.The equipment must also be
installed using an acceptable method of connections. The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas.
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet or on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Part 68
The FCC requires that you connect your cordless telephone to the
nationwide telephone network through a modular telephone jack (USOC
RJ11C or RJ11W).
Caution: Users should not attempt to make such connections
themselves, but should contact appropriate electric
inspection authority, or electrician, as appropriate.
Notice: The REN assigned to this device denotes the number
of devices you may connect to the telephone loop
which is used by the device to prevent overloading.The
termination on a loop may consist of any combination
of devices subjected only to the requirement that the
sum of the REN does not exceed five(5.0).
Your telephone company may discontinue your service if your equipment
causes harm to the telephone network. They will notify you in advance
of disconnection, if possible. During notification, you will be informed
of your right to file a complaint with the FCC.
If it is determined that your telephone equipment is malfunctioning, the
FCC requires that it not be used and that it be unplugged from the
modular jack until the problem has been corrected. Repairs to this
telephone equipment can only be made by the manufacturer or its
authorized agents or by others who may be authorized by the FCC. For
repair procedures, follow the instructions outlined under the VTECH
LimitedWarranty.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|