Uniden Cordless Telephone DECT2185 User Manual

DECT2185 Series User's Guide  
What's in the box?  
Base AC adapter  
(PS-0034)  
Battery  
cover  
DECT2185 base with  
answering system and  
cordless handset  
Telephone  
cord  
Rechargeable  
battery pack  
(BT-1016)  
You might also find:  
DCX210  
If you purchased You should  
Charger AC  
adapter  
accessory  
handset &  
charger  
model number:  
DECT2185  
have:  
None  
(PS-0035)  
DECT2185-2  
DECT2185-3  
DECT2185-4  
DECT2185-5  
DECT2185-6  
1 of each  
2 of each  
3 of each  
4 of each  
5 of each  
Battery  
cover  
Rechargeable  
battery pack  
(BT-1016)  
If any items are missing or damaged, contact our Customer Care  
Line immediately. Never use damaged products!  
Need Help? Get answers 24/7 at our website: www.uniden.com.  
If You...  
Contact Uniden’s...  
Phone Number  
817-858-2929 or  
800-297-1023  
have a question or problem  
Customer Care Line*  
need a replacement part or  
an accessory (such as a wall  
mount bracket)  
Parts Department*  
800-554-3988  
need special assistance due  
to a disability  
800-874-9314  
(voice or TTY)  
Accessibility Help Line  
* During regular business hours, Central Standard Time. Visit our website for detailed business hours.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing Your Phone  
Charge the Battery  
1) Unpack all handsets, battery packs, and  
battery covers. If any battery cover is  
already on the handset, press in on the  
notch and slide the cover down and off.  
2) Line up the red and black wires  
on the battery pack with the  
label inside the handset.  
Black  
Red  
3) Push the connector in until it  
clicks into place; tug gently  
on the wires to make sure  
the battery pack is securely  
connected.  
4) Place the cover over the battery  
compartment and slide it up into place.  
5) Connect the base AC adapter to the AC IN  
7.8V jack on the rear of the base. Route  
the cord through the molded wiring  
channel as shown.  
6) If you have accessory  
handsets, connect a  
charger AC adapter  
to each charger's AC  
IN 8V jack and set the  
plug into the notch as  
shown. (These  
adapters might  
already be  
connected.)  
7) Plug the other end of each adapter into  
a standard 120V AC power outlet.  
V
8
N
I
C
A
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8) Place a handset in the base and any accessory handset(s) in the  
charger(s) with the display(s) facing forward. The  
ChArGE light on the base and each charger  
should all turn on.  
If...  
Try...  
the ChArGE  
light does  
not turn on  
-
-
-
reseating the handset.  
checking the AC adapter connection.  
seeing if the outlet is controlled by a  
wall switch.  
Charge all handsets completely (about 15  
hours) before using them.  
Connect the Telephone Cord  
Use the telephone cord to  
connect the TEL LINE jack to a  
standard telephone wall jack.  
Test the connection  
1) Pick up the handset from  
the cradle and press  
TaLk  
. You should hear a  
dial tone, and the display  
should say Talk  
.
If...  
Try...  
you don't hear a dial tone or the checking the connection between  
display says Check Tel Line  
the base and the phone jack.  
ENd  
2) Make a quick test call. (Press  
to hang up.)  
If...  
Try...  
you keep hearing a dial tone changing the dial mode (see page 25).  
see page 24 for tips on avoiding  
interference.  
there's a lot of noise or static  
3) Test any accessory handsets the same way. If you can't get a  
dial tone or the handset display says Unavailable, try moving the  
handset closer to the base or resetting it (see page 25). Charge  
all handsets completely (about 15 hours) before using them.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Getting to Know Your Phone  
Parts of the Base  
If the key name is spelled out on the key itself, it's not labeled in the  
drawing below.  
PHONEBOOK/LEFT  
PLAY/STOP  
Display  
Speaker  
UP  
CALLER ID/RIGHT  
DOWN  
DO NOT DISTURB  
DELETE  
FIND HANDSET/  
INTERCOM  
SPEAKER  
Charging  
contacts  
Twelve-key  
dial pad  
Microphone  
(on back)  
Base keys and how they work  
Key name  
What it does  
(and icon)  
-
-
-
While this station is ringing: mute the ringer for this call only.  
During a call: mute the microphone.  
While entering text: delete one character, or press & hold to  
delete all the characters.  
CLEAr/MUTE  
-
-
In standby: open the menu.  
In the menu or any list: select the highlighted item.  
MENU/SELECT  
rEDIAL/PAUSE  
PLAY/STOP  
-
-
In standby: open the redial list.  
While entering a phone number: insert a 2-second pause.  
-
-
-
In standby: start playing messages.  
While a message is playing: stop playing messages.  
In the menu or a list: exit the menu completely.  
(
)
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Key name  
(and icon)  
What it does  
-
-
In standby or during a call: open the phonebook.  
In any menu or list: go up one level. (If you are already at  
the top level, the phone exits the menu and returns to the  
previous operation.)  
During text entry: move the cursor to the left.  
While playing messages: for the first 2 seconds, go to the  
previous message; after that: go to the start of this message.  
PhONEBOOK/  
LEFT  
(
/
)
-
-
CALLEr ID/  
rIGhT  
-
-
-
In standby or during a call: open the Caller ID list.  
During text entry: move the cursor to the right.  
While a message is playing: skip to the next message.  
(
/
)
-
-
In standby: increase the ringer volume.  
During a speakerphone call or while a message is playing:  
increase the speaker volume.  
UP (  
)
-
In the menu or any list: move the cursor up one line.  
-
-
In standby: decrease the ringer volume.  
During a speakerphone call or while a message is playing:  
decrease the speaker volume.  
DOWN (  
ON/OFF  
)
-
-
In the menu or any list: move the cursor down one line.  
In standby: turn the answering system on or off.  
-
-
While a message is playing: delete this message.  
In standby: delete all messages.  
DELETE (  
)
DO NOT  
DISTUrB (  
-
In standby: turn the Do Not Disturb feature on or off (see  
page 14).  
)
FLASh  
-
-
During a call: switch to a waiting call.  
While the phone is ringing: add the incoming caller ID to the  
call block list (block the call).  
BLOCK  
FIND hANDSET/  
INTErCOM  
-
-
In standby: page a handset using the intercom.  
During a call: put the call on hold & start a call transfer.  
SPEAKEr  
-
-
In standby: start a speakerphone call (get a dial tone).  
During a speakerphone call: hang up.  
(
)
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLEAR/  
UP  
Parts of the handset  
If the key name is spelled out  
on the key itself, it's not  
labeled in the drawing to the  
right.  
INTERCOM  
CALLER ID/  
RIGHT  
PHONEBOOK/  
LEFT  
DOWN  
SPEAKER  
Twelve-  
key dial  
pad  
REDIAL/  
PAUSE  
MESSAGES/  
MUTE  
Charging  
contacts  
Microphone  
Handset keys and how  
they work  
Key name  
What it does  
(and icon)  
-
-
-
In standby: increase the ringer volume.  
During a call: increase the call volume.  
In the menu or any list: move the cursor up one line.  
UP (  
)
CALLEr ID/  
-
-
In standby or during a call: open the Caller ID list.  
During text entry: move the cursor to the right.  
rIGhT (  
)
-
-
-
In standby: decrease the ringer volume.  
During a call: decrease the call volume.  
In the menu or any list: move the cursor down one line.  
DOWN (  
)
-
-
In standby: open the menu.  
In the menu or any list: select the highlighted item.  
During a call: hang up.  
In the menu or any list: exit & go to standby.  
MENU/SELECT  
END  
-
-
-
-
-
In standby: page another station using the intercom.  
During a call: put the call on hold & start a call transfer.  
While entering text: delete one character, or press & hold to  
delete all the characters.  
CLEAr/  
INTErCOM  
-
-
-
In standby or during a call: open the phonebook.  
In the menu: go back to the previous screen.  
During text entry: move the cursor to the left.  
PhONEBOOK/  
LEFT (  
)
-
-
In standby: start a telephone call (get a dial tone).  
During a call: switch to a waiting call.  
TALK/FLASh  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Key name  
(and icon)  
What it does  
SPEAKEr (  
)
-
Switch a normal call to the speakerphone (& back).  
rEDIAL/PAUSE  
-
-
In standby: open the redial list.  
While entering a phone number: insert a 2-second pause.  
(
)
-
While the phone is ringing: add the incoming Caller ID  
information to the call block list (block the call).  
BLOCK  
-
-
-
In standby: access your answering system.  
During a call: mute the microphone.  
While the phone is ringing: mute the ringer for this call only.  
MESSAGES/  
MUTE (  
)
reading the Displays  
On the base  
On the handset  
Status icons  
Time  
Answer ON  
Status  
Answering  
icons  
system status  
12:00A  
Handset #1  
New CID: 5  
Day and  
Message  
counter  
time  
SUN 12:00 AM  
Handset  
banner  
Caller ID  
Caller ID  
New CID: 5  
count  
count  
The table below shows the possible icons and what they mean. Since  
the icons appear based on what you're doing with the phone, you  
won't ever see all of these icons at the same time.  
Icon  
What it means  
The ringer is turned off: this station will not ring when a call  
comes in.  
You have a voice message waiting (see the section titled  
"Using Voice Message Notification" on page 15).  
Privacy Mode is on: no other station can join your call.  
The speakerphone is on.  
The microphone is muted, & the caller can't hear you.  
(Handset only) T-coil mode is on. (See "Do you use a T-coil  
hearing aid?" on page 24.)  
(Handset only) The battery is 1) fully charged, 2) half charged,  
3) getting low, or 4) empty.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the Menus  
The menus are designed to be as easy as possible. Some users don't  
even need the manual once they know how to perform these actions:  
MENU/SELECT  
Open the menu Press  
.
The arrow cursor on the left side of the line shows which  
UP  
Move the cursor menu item is currently highlighted. Use  
to move the  
DOWN  
cursor up &  
to move it down.  
MENU/  
Move the cursor to highlight the option, then press  
Select an option  
Go up one screen Press  
SELECT  
.
PhONEBOOK/LEFT  
.
END  
PLAY/STOP  
.
On the handset, press  
(If you open the menu during a call, use  
back out of the menu without hanging up.)  
; on the base, press  
Close the menu  
PhONEBOOK/LEFT  
to  
If you don't press any  
keys for thirty  
seconds, the  
To open the menu,  
press MENU/SELECT.  
To select the  
highlighted  
option, press  
MENU/SELECT.  
phone times out  
and exits the  
menu. (When  
setting the day  
and time, the time-  
out period is  
extended to two  
minutes.)  
Handset Setup  
Ans. Setup  
Use UP and  
OR  
DOWN to move  
the cursor.  
Day & Time  
To close the menu,  
press END on the  
handset or PLAY/  
STOP on the base.  
Global Setup  
Using the Base Menu  
You have the following options from the base:  
Reset the voice message waiting indicator to bring it back  
into sync with your voice mail service (see page 15).  
VMWI Reset  
Call Blocking  
Block unwanted calls from up to 20 phone numbers and  
manage your call block list (see page 14).  
Base Language Change the display language.  
Register additional handsets to the base or re-register  
a handset that you had to reset for some reason (see  
"Resetting and Registering Handsets" on page 25).  
Register  
Handset  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the handset Menus  
Handset Setup  
You can change these settings separately for each handset.  
Turn on T-coil mode to reduce noise on some hearing  
T-coil  
aids (see "Do you use a T-coil hearing aid?" on page 24).  
Choose one of four melodies or three tones for the  
handset's main ring tone. As you highlight each ring  
Ringer Tones  
tone, the phone plays a sample of the tone. When you  
MENU/SELECT  
hear the tone you want, press  
.
Turn on the personal ring feature. If you have Caller ID,  
this feature lets you assign special ring tones to anyone  
in your phonebook: this handset will use the special  
ring tone when that person calls.  
Personal Ring  
Autotalk  
Turn on Auto Talk so you can answer the phone just by  
picking up the handset from the cradle (without having  
to press any buttons).  
Turn on Any Key Answer so you can answer the phone  
by pressing a key on the twelve-key dial pad.  
Any Key Answer  
Banner  
Change the name used on the handset's display.  
Handset Language Change the display language.  
Key Touch Tone  
Have the keypad sound a tone when you press a key.  
Ans. Setup  
This menu controls the options and settings for your answering  
system (see "Ans. Setup menu options" on page 18).  
Day & Time  
You need to set the day & time so messages get the right time stamp.  
Up  
doWN  
MENU/sELECT  
to choose the day of the week; press .  
1) Use  
&
2) Use the number keypad to enter the hour and minutes.  
Up  
doWN  
MENU/sELECT  
to select AM or PM; press .  
3) Use  
&
Global Setup  
The settings on this menu apply to all handsets and the base. Before  
changing these settings, make sure the phone is in standby and all  
handsets are within range of the base. (Only one handset at a time  
can change these settings.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Enter your area code so the phone hides the area code on  
Area Code  
Dial Mode  
incoming local calls (see "Using Seven-digit Dialing" on page 12).  
Change the way your phone communicates with the telephone  
network (see "Changing from Tone to Pulse Dialing" on page 25).  
Set Line  
Mode  
Do not change this setting unless instructed to by customer  
service.  
Call Blocking  
This menu lets you block unwanted calls from up to 20 phone  
numbers and manage your call block list (see page 14).  
Entering Text on Your Phone  
When you want to enter text into your phone (for example, a name  
in the phonebook), use the twelve-key dial pad to enter the letters  
printed on the number keys. Here's how it works:  
The phone enters the letters in the order they appear on the key.  
2
For example, if you press the number key once, the phone  
2
enters the letter  
A
. Press twice for  
B
, and three times for  
C.  
If you press the key again after the last letter, the phone starts the  
same letter sequence with small letters. If you press four times  
2
2
in a row, the phone enters  
and six times for  
a
(small letter). Press five times for  
b,  
c
.
If you see the icon [Aa] in the display, the phone enters capital  
letters first (A B C), then small letters (a b c), then the number on  
the key ( ). The icon [aA] means the phone starts at the small  
2
letters, so it enters small letters first, then the number on the key,  
then capital letters.  
The phone automatically uses a capital letter for the first letter and  
any letter right after a space; all other times, it uses small letters.  
If two letters in a row use the same number key, enter the first  
CaLLEr Id/rIGHT  
letter, then use  
to move the cursor to the next  
position to enter the second letter.  
To  
Follow these steps  
Switch between capital  
& small letters  
Press  
.
PhONEBOOK/LEFT  
CALLEr ID/rIGhT  
Press  
to move the cursor to the left  
to move the cursor to the right.  
Move the cursor  
or  
#
.
Leave a blank space  
Press  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To  
Follow these steps  
Move the cursor to the letter you want to erase and  
CLEAr CLEAr/INTErCOM  
CLEAr/  
Erase one letter  
press  
(
on the handset;  
MUTE  
on the base).  
CLEAr  
Erase the entire entry Press & hold  
Enter punctuation or a  
.
0
Press to rotate through the available symbols.  
symbol  
Using Your Phone  
From a handset From the base  
From a handset  
To...  
speakerphone  
speakerphone  
make a call: Dial  
the number, then  
TALK/FLASh  
SPEAKEr  
SPEAKEr  
SPEAKEr  
SPEAKEr  
Press  
. Press  
.
Press  
Press  
Press  
.
.
.
TALK/FLASh  
SPEAKEr  
answer a call  
Press  
Press  
. Press  
.
END  
or put the handset in the  
hang up  
cradle.  
switch between the  
speaker & earpiece  
SPEAKEr  
SPEAKEr  
.
Press  
.
Press  
NA  
MESSAGES/MUTE  
Press again to turn the microphone back on.  
CLEAr/MUTE  
.
mute the micro-  
phone during a call  
Press  
.
Press  
FIND hANDSET/  
Press  
CLEAr/INTErCOM  
Press  
.
INTErCOM  
.
put a call on hold  
If the call is on hold for 5 minutes, it will be disconnected.  
return to a call on  
hold  
TALK/FLASh  
SPEAKEr  
SPEAKEr  
.
Press  
. Press  
.
Press  
While the phone is  
mute the ringer for While the phone is ringing, press  
CLEAr/  
ringing, press  
MESSAGES/MUTE  
this call only  
.
MUTE  
.
Changing the Volume  
You can set the volume of the ringer and speaker separately for the  
base and each handset; you can also set the earpiece volume on  
Up  
doWN  
each handset. For each item, press  
to make it louder or  
to  
make it softer. The available volume levels and how change them are  
listed below:  
ꢀ0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Change the When  
On the base  
On a handset  
ringer  
volume  
the phone is in  
standby  
select Off, Low,  
select Off, Low,  
Medium, or High Medium, or High  
earpiece  
volume  
you are on a normal  
call  
choose one of 6  
volume levels  
NA  
you use the speaker-  
phone for a call or  
getting messages  
speaker  
volume  
choose one of 10  
volume levels  
choose one of 6  
volume levels  
Using the redial List  
The phone saves the last 5 numbers you dial on each station. To  
rEdIaL/paUsE  
Up  
doWN  
and to scroll  
open the redial list, press  
; use  
pHoNEbook/LEfT  
through the list. To close the list, press  
. With the  
phone in standby, open the list and find the number you want. Then:  
TALK/FLASh  
SPEAKEr;  
or  
On the handset, press  
on the base, press  
to redial the selected number  
to delete the number  
SPEAKEr  
.
MENU/SELECT  
Press  
& select Delete Entry  
.
MENU/SELECT  
to save it to the phonebook Press  
& select Store Into Pb  
.
Using Caller ID and Call Waiting  
You have to subscribe to Caller Id, Call Waiting, and Caller Id  
on Call Waiting services to use the features described in this  
section: contact your telephone provider for more information.  
When a call comes in, the phone displays the caller’s number and  
name (if available). The phone saves the information for the last 30  
received calls to the CID list. When it's in standby, the phone displays  
how many calls came in since the last time you checked the CID list.  
CALLEr ID/rIGhT  
Open the CID list  
Press  
.
DOWN  
oldest. Press  
Scroll through the CID Press  
to scroll through the list from newest to  
UP  
to scroll from oldest to newest.  
list  
PhONEBOOK/LEFT  
.
Close the CID list  
Press  
Dialing from the Caller ID list  
1) Find the entry you want to dial.  
2) If the number is a toll or long distance call, but there's no 1 at the  
front of the CID record, press to add the 1.  
ꢀꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
TaLk/fLasH  
spEakEr  
to dial the number;  
3) On the handset, press  
on the base, press  
or  
spEakEr  
.
TaLk/fLasH  
spEakEr  
before you open the CID  
(You can also press  
or  
MENU/sELECT  
list. Find the number you want to dial, then press  
.)  
Caller ID menu options  
Open the CID list with the phone in standby. Find the number you  
MENU/sELECT  
want and press  
. Choose one of these CID menu options:  
Delete Entry  
Erase this Caller ID number.  
Add this number to this station's phonebook. The phone  
prompts you to enter a name & edit the number; handsets  
also prompt you to choose a personal ring.  
Store Into Pb  
Erase this station's CID list. (This does not affect the CID  
lists saved on any other stations.)  
Delete All  
(Handset only) Add the number to the call block list (see  
page 14).  
Add Call Block  
Using Call Waiting  
If you get a Call Waiting call, the phone sounds a tone and displays  
fLasH TaLk/  
any CID information received for the waiting call. Press  
(
fLasH  
on a handset) to switch between the current call and the waiting  
call; remember, each time you switch, there is a short pause before  
you're connected to the other caller.  
Using Seven-Digit Dialing  
If you can make a local call by dialing only seven digits instead of ten,  
you can tell the phone to hide your local area code in the CID list.  
do not enter an area code if your phone company requires ten-  
digit dialing. You might not be able to dial from the CId list.  
1) From any handset, open the menu with the phone in standby.  
2) Select Global Setup, then select Area Code  
.
0 - 9  
3) Use the number keypad ( ) to enter your three-digit area code.  
MENU/sELECT  
4) Press  
when you’re finished.  
The phone uses the programmed code as a filter. When calls  
come in, the phone compares the area code to the programmed  
one. If they match, the phone hides the area code in the CID list.  
#
While reviewing the list, press to toggle the area code off & on.  
ꢀꢁ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using the Phonebook  
Each station can store up to 70 entries in its phonebook.  
PhONEBOOK.  
Open/close the phonebook Press  
DOWN  
from A to Z or  
Press  
to scroll through the phonebook  
Scroll through the entries  
UP  
to scroll from Z to A.  
Jump to entries that start  
with a certain letter  
Press the number key corresponding to the  
letter you want to jump to.  
1. Find the entry you want to dial.  
Dial an entry  
TALK/FLASh  
or  
2. On the handset, press  
SPEAKEr  
SPEAKEr  
.
; on the base, press  
Phonebook menu options  
Open the phonebook with the phone in standby, then press  
MENU/  
sELECT  
to open the phonebook menu. Choose one of these options:  
Add an entry to your phonebook. The phone prompts you to enter  
the name & phone number. (Handsets will also prompt you to  
choose a personal ring.)  
Create  
New  
Copy All Copy the whole phonebook to another station.  
Delete  
All  
Erase all the entries in this station's phonebook. (This does not  
affect the entries saved on any other stations.)  
Phonebook entry options  
With the phone in standby, open the phonebook and find the entry  
MENU/sELECT  
you want. Press  
to open the individual phonebook entry  
menu. Choose one of these options:  
Edit this entry. The phone prompts you to enter the name & phone  
number. (Handsets will also prompt you to choose a personal ring.)  
Edit  
Copy  
Copy this entry to another station.  
Delete Erase this entry.  
Chain Dialing  
If you often have to enter a series of digits or a code number  
during a call, you can save that code number to a phonebook  
entry and use the phonebook to send the code number.  
ꢀꢂ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Enter the code number (up to 20 digits) into the phonebook just  
like a regular phonebook entry. Be sure to enter the code number  
into the phonebook exactly as you would enter it during a call.  
When you hear the prompt that tells you to enter the number, open  
the phonebook and find the entry that contains your code number.  
MENU/sELECT  
Press  
mind, use  
to transmit the code. Or, if you change your  
pHoNEbook/LEfT  
to close the phonebook.  
Finding a Lost handset  
With the phone in standby, press  
fINd HaNdsET/INTErCoM  
on the base.  
Select the handset you want to find (or All to page all handsets). The  
fINd HaNdsET/  
paged handset(s) beep for 1 minute or until you press  
INTErCoM  
TaLk/fLasH  
ENd  
again or press  
followed by on the handset.  
Using Special Features  
Using Do Not Disturb  
The Do Not Disturb or DND feature turns off the ringers of the  
base and all handsets at the same time.  
do NoT dIsTUrb  
With the phone in standby, press and hold  
on the  
base. The phone automatically turns on the answering system and  
shows Do Not Disturb in the display on all stations.  
do NoT dIsTUrb  
again.  
To cancel, press  
If you turn the answering system off while dNd is on, the phone  
turns off dNd along with the answering system.  
Using Call Block  
If you subscribe to Caller ID, you can save phone numbers to the call  
block list. When a call comes in, the phone compares the received  
phone number to the numbers on the call block list. If the phone  
number is on the list, the phone replaces the caller's name with Call  
Blocked and disconnects the call. (The caller hears a reject tone.)  
The call block list holds 20 entries, and all stations share the same  
list. You can add entries through the Call Blocking menu, by selecting  
Add Call Block in the CID menu, or by blocking incoming calls. (Only  
one station can edit the call block list at a time.)  
Blocking incoming calls  
When the phone rings, wait until the display shows the Caller ID  
information (usually after the second ring). If you want to block the  
ꢀꢃ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
bLoCk  
call and add this number to the call block list, press  
. When the  
MENU/sELECT  
bLoCk  
phone asks you to confirm, press  
or  
.
blocking an incoming call from an "Unknown" or "private"  
number is the same as selecting Unknown Number or Private  
Number from the Call Blocking menu.  
Call Blocking menu options  
With the phone in standby, open the menu and select Call Blocking  
Choose one of these options:  
.
View Number See the numbers on your call block list.  
(Handset only) Add an entry to your call block list. The phone  
will prompt you to enter a name & phone number.  
Create New  
Private  
Number  
(Handset only) Block all calls from numbers reported by CID  
as "Private." (This does not count as one of the 20 entries.)  
Unknown  
Number  
(Handset only) Block all calls from numbers reported by CID  
as "Unknown". (This does not count as one of the 20 entries.)  
Call block entry options  
With the phone in standby, open the call block list and find the entry  
MENU/sELECT  
you want. Press  
to open the individual entry menu.  
Choose one of these options:  
(Handset only) Edit this entry. The phone will prompt you to edit  
the name & phone number.  
Edit  
Delete Erase this entry from the list & allow calls from this number.  
Using Voice Message Notification  
This feature supports frequency-shift keying (fsk) message  
notification. Contact your voice mail provider for more details.  
If you subscribe to a voice mail service, your phone  
can notify you when you have a new message  
waiting. When you have new messages, the voice  
message icon  
(
) appears in the display, and the  
new message light (at the top of the handset) blinks.  
Resetting the voice message indicator  
If the voice message icon remains after you check  
your messages, you can reset it. Open the menu on  
the base and select VMWI Reset. Select Yes to reset the indicator.  
ꢀꢄ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Using Multi-station Features  
The expandable base and the cordless handset give you some useful  
multi-station features. (A station can be any handset or the base.)  
Expanding Your Phone  
Your base supports a total of six cordless handsets: the one that  
came with the base and up to five DCX210 accessory handsets.  
Your base might be compatible with other Uniden accessory  
handsets: please visit our website for a list of compatible handsets.  
Accessory handsets must be registered to the base before you  
can use them. Handsets that aren't registered display a Handset  
not registered message. For instructions on registering handsets to  
this base, see page 25 or the manual for the accessory handset.  
Any accessory handsets that came packaged with the base are  
already registered to that base for you.  
If a handset was previously registered to a base, you have to reset  
it so you can register it to a new base (see page 25 for DCX210).  
Using Conference Calling  
When an outside call comes in, the base  
and two handsets can join in a  
Outside call  
Handset  
#2  
conference call with the outside caller. To  
spEakEr  
join the call, just press  
on the  
Handset  
#1  
TaLk/fLasH  
base or  
on a handset. To leave  
Base  
speakerphone  
the conference call, hang up normally;  
the other station remains connected to  
the call. (You can also use the handset speakerphone for a  
conference call, just like you can with a normal call.)  
Using Privacy Mode  
You can prevent other stations from joining a call. Start your call as  
MENU/sELECT  
usual, then press  
: the display shows Call Privacy. Press  
MENU/sELECT  
again to turn privacy mode on (you'll see a in the  
display). When you hang up, privacy mode turns off automatically.  
As long you have privacy mode on, no other stations can interrupt  
your call. To allow another station to join the call, just turn privacy  
MENU/sELECT  
mode off by repeating the process above (press  
twice).  
ꢀꢅ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using Call Transfer  
To...  
From the base  
From a handset  
FIND hANDSET/INTErCOM  
1. Press  
put the call on hold.  
CLEAr/INTErCOM  
to 1. Press to  
put the call on hold.  
2. Select the station you want to transfer the call to, or select  
transfer a  
call  
All to page all the stations at the same time.  
When the other station accepts the call, you'll be disconnected,  
but you can join the call again.  
SPEAKEr  
TALK/FLASh  
Press to return to  
the call.  
cancel a  
transfer  
Press  
call.  
to return to the  
1. To answer the page & speak to the transferring station,  
accept a  
transferred  
call  
FIND hANDSET/INTErCOM  
CLEAr/INTErCOM.  
press  
.
press  
press  
2. To accept the call,  
SPEAKEr  
TALK/FLASh  
.
press  
.
Using the Intercom  
Here are some things you need to know about using the intercom:  
Whenever the phone is in standby, you can make an intercom call  
between stations without using the phone line.  
You can make an intercom call from any station, but only two  
stations can be in an intercom call at any time.  
If an outside call comes in during an intercom call, the phone shows  
the CID information. If the other station hasn't answered the page,  
the phone cancels the page so you can answer the incoming call.  
To...  
From the base  
From a handset  
FIND hANDSET/INTErCOM  
CLEAr/INTErCOM  
.
1. Press  
.
1. Press  
make an intercom  
page  
2. Select the station you want to talk with, or select All to  
page all the stations at the same time.  
FIND hANDSET/INTErCOM.  
END  
.
cancel a page  
Press  
Press  
FIND hANDSET/INTErCOM  
CLEAr/INTErCOM  
or  
answer an  
intercom page  
Press  
or Press  
SPEAKEr  
TALK/FLASh  
.
.
leave an intercom  
call  
FIND hANDSET/INTErCOM.  
END  
.
Press  
Press  
Press  
answer an outside  
call during an  
intercom call  
SPEAKEr.  
TALK/FLASh  
.
Press  
ꢀꢆ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the Answering System  
Setting Up Your Answering System  
You can set up your answering system from any handset.  
To...  
Follow these steps  
Your greeting can be between 2 seconds and 30 seconds  
long. If you don't record an outgoing message, the system  
uses a pre-recorded greeting: Hello, no one is available to  
take your call. Please leave a message after the tone.  
MESSAGES/MUTE  
1. Press  
to access the answering system. Wait  
Record your  
personal  
5
until the system finishes its announcements, or press  
(STOP)  
to skip them.  
outgoing  
8
.
2. Press  
message or  
greeting  
3. Wait for the system to say "Record greeting," then begin  
speaking.  
8
4. When you're finished, press to stop recording. The  
system plays back your new greeting.  
END  
5. To keep this greeting, press  
. To re-record it, go back to  
step 2.  
MESSAGES/MUTE  
1. Press  
to access the answering system. Wait  
Switch  
5
until the system finishes its announcements, or press  
between the  
pre-recorded  
greeting &  
your own  
greeting  
(STOP)  
to skip them.  
6
.
2. Press  
The system plays back the greeting it is currently  
using.  
6
3. Press again to switch greetings.  
1. Switch to your personal greeting following the steps above.  
2. While the system is playing back your greeting, press .  
Delete your  
greeting  
4
Ans. Setup menu options  
You can change the answering system options from any handset.  
Just open the menu and select Ans. Setup  
.
Enter a 2-digit PIN so you can access your answering  
system from any touch-tone phone (see page 21).  
Security Code  
Ring Time  
Set the number of rings (  
2
,
4
, or 6) before the answering  
system answers the phone. Choose Toll Saver (TS) to  
have the system pick up after 2 rings if you have new  
messages or after 4 rings if you don't.  
ꢀꢇ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Set the amount of time callers have to leave a message,  
Record Time  
either  
1
minute or  
4
minutes. Choose Announce Only if  
you don't want the system to let callers to leave a message.  
Have the system beep every 15 seconds when you have  
a new message; the beeping stops when you listen to all  
your new messages. (To mute the alert without listening to  
your messages, press any key on the base.)  
Message Alert  
Ans. Language Change the language of the system's voice prompts.  
Turn on the call screen feature so you can hear callers as  
they leave messages on the base speaker (see page 20).  
Call Screen  
Turn your answering system on or off. (To turn your  
Ans. On/off  
ON/OFF  
system on or off from the base, just press  
.)  
Getting Your Messages  
Accessing your answering system from a handset  
You can access your system from a handset whenever the phone is  
in standby.  
Press MESSAGES/MUTE to start  
remote operation mode.  
1:Repeat 3:Skip  
2:Play 4:Delete  
Use PHONEBOOK/  
LEFT to go to the  
previous option.  
6:SelectGreeting  
5:Stop  
[ / /select]  
8:RecNewGreeting  
Use CALLER ID/  
RIGHT to go to the  
next option.  
Press MENU/  
SELECT to choose  
the current option.  
Press END to exit remote  
operation mode.  
During remote operation, the phone beeps to let you know it's  
waiting for your next command.  
You can press the number key next to the commands instead of  
scrolling through them.  
If you don't press any keys for 30 seconds, the phone returns to  
standby.  
Only one handset can access the system at a time.  
ꢀꢈ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to operate your answering system  
From a handset (remote  
operation)  
To...  
From the base  
PLAY/STOP  
MESSAGES/MUTE  
.
Press  
Press  
The system announces the number of new & old messages,  
then plays the first new message followed by the day & time  
it was received. Then the system plays the new messages  
in the order they were received.  
play new  
messages  
restart the  
current message  
PhONEBOOK/LEFT  
1
Press  
.
Press or select 1:Repeat  
.
PhONEBOOK/LEFT  
repeatedly until you hear the repeatedly until you hear the  
message you want to replay. message you want to replay.  
1
Press  
Press or select 1:Repeat  
replay previous  
messages  
CALLEr ID/rIGhT  
3
skip a message Press  
.
Press or select 3:Skip.  
While the message is  
While the message is playing,  
delete a message  
DELETE  
4
playing, press  
.
press or select 4:Delete  
.
With the phone in standby,  
DELETE  
delete all of your press  
. When the  
Not available.  
messages  
system asks you to confirm,  
DELETE  
press  
again.  
After the system plays the new messages,  
play old  
messages  
PLAY/STOP  
PLAY/STOP  
2
press  
Press  
again.  
press or select 2:Play.  
end the  
operation  
END  
.
.
Press  
Screening Your Calls  
Another feature your answering system gives you is call screening.  
While the system is taking a message, you can hear the caller on the  
base speaker (if you turn on Call Screen) or from a handset.  
To...  
From the base  
From a handset  
hear the caller  
Just listen to the caller over  
MESSAGES/MUTE  
Press  
.
leaving a message the speaker.  
SPEAKEr  
TALK/FLASh  
.
answer the call  
mute the call screen  
without answering  
Press  
.
Press  
Press  
END  
or return the  
CLEAr/MUTE  
Press  
.
handset to the cradle.  
ꢁ0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
If you mute the call screen, the system continues taking the  
message: it just stops playing through the speaker.  
Only one handset at a time can screen calls. If another handset is  
screening the call, the handset beeps and returns to standby.  
Using the System While You're Away from home  
You can also operate your answering system from any touch-tone  
phone. Before you can use this feature, you have to program a  
security code.  
Programming a security code  
1) With the phone in standby, open the menu from any handset.  
2) Select Ans. Setup, then select Security Code  
.
3) Use the number keypad to enter a two-digit security code (01 to  
MENU/sELECT  
99). Press  
when you’re finished.  
remember to make a note of your new security code!  
Dialing in to your system  
1) Call your telephone number and wait for the system to answer. (If  
your answering system is off, it will answer after about ten rings  
and sound a series of beeps instead of your greeting.)  
0
2) During the greeting (or beeps), press and immediately enter  
your security code. (You have 3 tries to enter you security code:  
if you enter it wrong 3 times, the system hangs up and returns to  
standby.)  
3) The system announces the current time, the number of messages  
stored in memory, and a help prompt. Then it starts beeping  
intermittently to let you know it's waiting for your command.  
4) When you hear the intermittent  
0-1 Repeat message  
beeping, enter a command from the  
chart to the right.  
0-2 Play message  
0-3 Skip message  
If you don't press any keys for 15  
seconds, the phone will hang up and  
return to standby.  
0-4 Delete message  
0-5 Stop playback  
0-6 Turn the system on  
0-9 Turn the system off  
1-0 Hear help prompts  
ꢁꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Solving Problems  
If you have any trouble with your phone, try these simple steps first.  
If you still have a question, call our Customer Care Line listed on the  
front cover.  
If…  
Try…  
-
-
Checking the telephone cord connection.  
Disconnecting the base AC adapter. Wait a few  
minutes, then reconnect it.  
No stations can make  
or receive calls.  
-
-
Moving the handset closer to the base.  
Resetting the handset.  
One handset can’t  
make or receive calls.  
-
-
Making sure the ringer is turned on.  
Making sure Do Not Disturb is turned off.  
A station can make  
calls, but it won’t ring.  
-
-
Charging the battery for 15-20 hours.  
Checking the battery pack connection.  
A handset's display  
won't turn on.  
-
-
-
Charging the battery for 15-20 hours.  
Checking the battery pack connection.  
Resetting the handset.  
A handset is not  
working.  
-
-
-
Moving the handset closer to the base.  
Seeing if another station has Privacy Mode on.  
Making sure the base is plugged in.  
A handset says  
Unavailable  
.
-
-
-
Letting calls ring at least twice before answering.  
Seeing if the call was placed through a switchboard.  
Checking with your telephone service provider to  
make sure your Caller ID service is active.  
No stations will  
display any Caller ID  
information.  
-
-
Making sure you entered the correct area code. If  
you have to dial all 10 digits, you need to delete the  
area code (see Seven-digit Dialing on page 12).  
You may have to change the line mode. Contact  
customer service for more information.  
I can't dial from the  
Caller ID list.  
Caller ID displays  
briefly & then clears.  
I can’t transfer calls.  
-
-
Resetting all the handsets.  
Making sure both handsets are registered to this  
base.  
I can’t get two  
handsets to talk to the  
caller.  
-
-
Making sure no station is in Privacy Mode.  
The phone keeps  
ringing if I answer on  
an extension.  
You may have to change the line mode. Contact  
customer service for more information.  
ꢁꢁ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
If…  
Try…  
-
-
Making sure the answering system is turned on.  
Making sure the base AC adapter is plugged into a  
continuous wall outlet (i.e., not controlled by a wall  
switch).  
The answering system  
does not work.  
-
-
Making sure the Record Time is not set to  
The answering  
system won't record  
messages.  
Announce Only  
.
Deleting messages (the memory may be full).  
-
-
Making sure no other handset is using the system.  
Making sure the phone is in standby.  
A handset can't access  
the answering system.  
My outgoing message  
is gone.  
-
Seeing if there was a power failure. You may have to  
re-record your personal outgoing message.  
-
-
Making sure call screening is turned on.  
Changing the base speaker volume.  
I can’t hear the base  
speaker.  
-
The incoming messages may be too long. Remind  
callers to leave a brief message.  
Deleting messages (the memory may be full).  
Messages are  
incomplete.  
-
-
The system keeps  
recording if I answer  
on an extension.  
You may have to change the line mode. Contact  
customer service for more information.  
-
-
Seeing if you already have 6 handsets registered to  
this base.  
Resetting the handset.  
I can't register a  
handset.  
Weak or hard To hear Audio  
If a caller’s voice sounds weak or soft, the signal might be blocked by  
large metal objects or walls; you might also be too far from the base,  
or the handset’s battery may be weak.  
Try moving around while you’re on a call or moving closer to the  
base to see if the sound gets louder.  
Make sure the handset’s battery is fully charged.  
Try adjusting the earpiece volume or the audio tone (see below).  
Adjust the audio tone  
During a call, open the menu and select Audio Tone. Choose one of  
the three audio tone options: High Tone Natural Tone (recommended  
,
for hearing aid users), or Low Tone. You may have to experiment to  
figure out which audio tone works best for you.  
ꢁꢂ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Noise or Static On The Line  
Interference is the most common  
cause of noise or static on a  
cordless phone. Here are some  
common sources of interference:  
Do you use a T-Coil hearing aid?  
If you have a hearing aid  
equipped with a telecoil (T-coil)  
feature, the interaction between  
the hearing aid & digital cordless  
phones can cause noise in the  
handset. If you have a T-coil  
hearing aid & you have problems  
with noise on the line, try turning  
on T-coil mode. Open the menu.  
Select Handset Setup, then  
electrical appliances, especially  
microwave ovens  
computer equipment, especially  
wireless LAN equipment and  
DSL modems  
select T-coil  
.
radio-based wireless devices,  
such as room monitors,  
Using T-coil mode can shorten  
the handset’s talk time; make  
sure to watch the battery status  
and keep the battery charged.  
wireless controllers, or wireless  
headphones or speakers  
large florescent light fixtures  
(especially if they give off a buzzing noise)  
other services that use your phone line, like alarm systems,  
intercom systems, or broadband Internet service  
Here are some hints for when the static is...  
on 1 handset or in 1 location:  
on all handsets or in all locations:  
-
Check nearby for one of the common  
interference sources.  
-
Check near the base for the  
source of interference.  
-
Try moving the handset away from a  
suspected source, or try moving the  
suspected source so it’s not between  
the handset & the base.  
-
Try moving the base away from a  
suspected source, or turn off the  
source if possible.  
-
If the base has an adjustable  
-
Try moving closer to the base. There is antenna, try raising the antenna  
always more noise at the edges of the  
base's range. If the handset displays an  
Out of Range message, you need to  
move closer to the base.  
so it stands straight up.  
-
If you have any service that uses  
the phone line, you might need a  
filter (see below).  
Installing a line filter or DSL filter  
Sometimes, broadband Internet services  
that use the telephone line can interfere  
with phones. One of these services−DSL−  
often causes static on telephones. A DSL  
filter or telephone line filter usually solves  
ꢁꢃ  
Telephone  
wall jack  
Telephone  
cord  
DSL filter  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
this problem. The technician who installed your DSL service might  
have left some filters for you; if not, call your DSL provider or look in  
any electronics store.  
Plug the DSL filter into the telephone wall jack and plug your phone’s  
base into the filter. Make a test call to make sure the noise is gone.  
Changing from Tone to Pulse Dialing  
Your phone can communicate with the telephone network in two  
different ways: tone dialing or pulse dialing. These days, most  
telephone companies use tone dialing. If your phone company uses  
pulse dialing, you will need to change your phone’s dial mode.  
1) From a handset, open the menu & select Global Setup  
.
2) Select Dial Mode, then select Pulse. The phone sounds a  
confirmation tone.  
If you use pulse dialing and you need to send DTMF tones during a  
call (if you're using an automated response system, for example),  
press to temporarily switch to tone dialing. When the call ends, the  
phone automatically returns to pulse dialing mode.  
resetting and registering handsets  
If you are having trouble with a handset or if you want to replace one,  
you need to clear the registration information from the base and the  
handset:  
Do you have the base the handset is registered to?  
Yes  
No  
END  
#
END  
#
1. Press & hold  
and until the System 1. Press & hold  
and until  
Reset menu appears (about 5 seconds).  
2. Select Deregister HS. The display lists  
all registered handsets.  
the System Reset menu  
appears (about 5 seconds).  
2. Select Base Unavailable  
.
3. Select the handset you want to reset.  
4. When the phone asks you to confirm,  
select Yes. The handset clears its  
information from the base & deletes it  
own link to the base.  
3. When the phone asks you  
to confirm, select Yes. The  
handset deletes its own link  
without contacting the base.  
When you reset a handset (or if you buy a new one), that handset  
displays a Handset Not Registered message. If you see this message  
on a handset, you need to register it to a base before you can use it.  
ꢁꢄ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Registering a handset  
1) On the base, open the menu and select Register Handset. The  
display should say Handset Registering  
.
#
2) On the handset you want to register, press and hold until the  
handset display says Handset Registering (about 2 seconds).  
3) In about 30 seconds, the handset display should say Registration  
TaLk/fLasH  
Complete. Press  
and make sure you get a dial tone.  
If...  
Try...  
-
-
you don't hear a dial tone  
the display says Registration Failed  
Making sure the handset is fully  
charged, then start over at step 1.  
To register a handset to a different base, see the section  
"Expanding Your phone" in the user's guide for the other base.  
handling Liquid Damage  
Moisture and liquid can damage your cordless phone.  
If the handset or base is exposed to moisture or liquid, but only the  
exterior plastic housing is affected, wipe off the liquid, and use as  
normal.  
If moisture or liquid has entered the plastic housing (i.e. liquid can  
be heard in the phone or liquid has entered the handset battery  
compartment or vent openings on the base), follow these steps:  
handset  
Base  
1. Remove the battery cover & disconnect the  
battery.  
1. Disconnect the AC  
adapter to cut off the  
power.  
2. Let dry for at least 3 days with the battery  
disconnected and the cover off for ventilation. 2. Disconnect the  
telephone cord.  
3. After the handset dries, reconnect the battery  
pack and replace the cover. Recharge the  
battery fully (15-20 hours) before using.  
3. Let dry for at least 3 days  
before reconnecting.  
IMporTaNT: You must unplug the telephone line while  
recharging the battery pack to avoid charge interruption.  
CAUTION! DO NOT use a microwave oven to speed up the  
drying process. This will cause permanent damage to the  
handset, base and the microwave oven.  
ꢁꢅ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Important Information  
Terms Used In This Guide  
Accessory An extra handset that can register to and be used with an expandable phone base. All accessory  
handset  
handsets must be registered to a base before you can use them.  
The main part of the phone. It connects to your phone line and lets you make and receive calls.  
Most bases also have a cradle to store a handset.  
Base  
CIDCW  
(CID on Call Waiting.) A service that shows CID for calls that come in during another call.  
Call Waiting A service that lets you receive calls while you are on another call.  
Caller ID  
Charger  
(Also called CID.) A service that shows the name and number of incoming callers.  
A cradle that stores and charges a handset but doesn’t connect to the phone line.  
The part of the phone that stores a handset. While in a cradle, a handset is always in standby,  
and any keys are locked.  
Cradle  
During a call The station is currently on a call or has activated a dial tone.  
Handset A cordless handset that you use to dial the phone and talk to callers.  
In standby The phone is inactive: there is no dial tone, no station is on a call or listening to messages.  
Station Any handset or the base.  
Specifications  
Base  
Charger  
PS-00ꢂꢄ  
ꢀꢁ0V AC, ꢅ0 Hz  
Use only the supplied AC adapters.  
Be sure to use the proper adapter for  
the base & any chargers.  
Do not place the power cord where it  
creates a trip hazard or where it could  
become chafed & create a fire or  
electrical hazard.  
Part number PS-00ꢂꢃ  
Input voltage ꢀꢁ0V AC, ꢅ0 Hz  
AC  
adapter  
Output voltage ꢆ.ꢇV AC @ ꢃꢄ0mA ꢇV AC @ ꢂ00mA  
Part number BT-ꢀ0ꢀꢅ  
Capacity  
Battery  
pack  
ꢄ00mAh, ꢁ.ꢃV DC  
Do not place the base in direct sunlight or subject it to high temperatures.  
Battery Information  
Fully charged, the battery should provide about ꢀ0 hours of talk time and about ꢆ days of standby time.  
For best results, return the handset to the cradle after each call to keep it fully charged.  
Keep an eye on the battery status icon. When the battery gets too low, the handset shows a low battery  
alert. If you hear a strange beep during a call, check the display: if you see the low battery alert, finish  
your conversation as quickly as possible and return the handset to the cradle. If the handset is in  
standby, none of the keys will operate.  
With normal use, the battery should last about one year. Replace the battery when the talk time  
becomes short even when the battery is charged. To buy a replacement battery, call the Parts  
Department listed on the front cover.  
Rechargeable Nickel-Metal-Hydride Battery Warning  
CAUTION! Risk of explosion if battery is replaced by an incorrect type! Dispose  
of used batteries according to the instructions. Do not open or mutilate  
the battery. Disconnect the battery before shipping this product.  
This equipment contains a rechargeable Nickel-Metal-Hydride battery.  
The rechargeable batteries contained in this equipment may explode if disposed of in a fire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Nickel is a chemical known to state of California to cause cancer.  
Do not short-circuit the battery.  
Do not charge the rechargeable battery pack used in this equipment with in any charger other than the  
one designed to charge this battery pack as specified in the owner's manual. Using another charger  
may damage the battery pack or cause the battery pack to explode.  
Rechargeable Batteries Must Be Recycled or Disposed of Properly.  
Uniden works to reduce lead content in PVC coated cords in our products & accessories.  
Warning! The cords on this product and/or accessories contain lead,  
a chemical known to the State of California to cause birth defects  
or other reproductive harm. Wash hands after handling.  
Compliance information  
FCC Part 68 information  
This equipment complies with Part ꢅꢇ of the FCC rules & the requirements adopted by the ACTA. On  
the bottom of this equipment is a label that contains, among other information, a product identifier in the  
format US: AAAEQ##TXXXX. If requested, this number must be provided to the phone company.  
An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment  
is provided (i.e., RJꢀꢀC) in the packaging with each piece of approved terminal equipment. A plug &  
jack used to connect this equipment to the premises wiring & telephone network must comply with the  
applicable FCC Part ꢅꢇ rules & requirements adopted by the ACTA. A compliant telephone cord &  
modular plug is provided with this product. It is designed to be connected to a compatible modular jack  
that is also compliant. See installation instructions for details.  
The REN is used to determine the number of devices that may be connected to a phone line. Excessive  
RENs on a phone line may result in devices not ringing in response to an incoming call. In most but not  
all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may  
be connected to a line, as determined by the total RENs, contact the telephone provider. The REN for this  
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented  
by ## are the REN without a decimal point (e.g., 0ꢂ is a REN of 0.ꢂ).  
If this equipment causes harm to the telephone network, the telephone company will notify you in advance  
that temporary discontinuance of service may be required. But if advance notice isn't practical, the  
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to  
file a complaint with the FCC if you believe it is necessary. The telephone company may make changes  
in its facilities, equipment, operations or procedures that could affect the operation of the equipment.  
If this happens the telephone company will provide advance notice in order for you to make necessary  
modifications to maintain uninterrupted service.  
Please follow instructions for repairing, if any (e.g. battery replacement section); otherwise do not  
substitute or repair any parts of the device except as specified in this manual. Connection to party line  
service is subject to state tariffs. Contact the state public utility commission, public service commission or  
corporation commission for information. This equipment is hearing aid compatible.  
If you experience trouble with this equipment, contact the manufacturer (see the cover of this manual for  
contact information) or an authorized agent. If the equipment is causing harm to the telephone network,  
the telephone company may request that you disconnect the equipment until the problem is resolved.  
If your home has wired alarm equipment connected to a phone line, be sure that installing the system  
does not disable your alarm equipment. If you have questions about what will disable alarm equipment,  
contact your telephone company or a qualified installer.  
Any changes or modifications to this product not expressly approved by the manufacturer or other party  
responsible for compliance could void your authority to operate this product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning  
strikes, are very destructive to telephone equipment connected to AC power sources. To minimize  
damage from these types of surges, a surge arrestor is recommended.  
FCC Part 15 information  
This device complies with part ꢀꢄ of the FCC rules. Operation is subject to the following two conditions:  
(ꢀ) This device may not cause harmful interference, & (ꢁ) This device must accept any interference  
received, including interference that may cause undesired operation. Privacy of communications may not  
be ensured when using this phone.  
FCC PART 15.105(b): Note: This equipment has been tested & found to comply with the limits for a Class  
B digital device, pursuant to part ꢀꢄ of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates, uses & can  
radiate radio frequency energy and, if not installed & used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off & on, the user is encouraged to try to  
correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This product complies with FCC radiation exposure limits under the following conditions:  
The base must be placed to allow a minimum of ꢁ0 cm (ꢇ inches) between the antenna and all persons  
during normal operation.  
The base must not be collocated or operated in conjunction with any other antenna or transmitter.  
The handset is designed for body-worn operation and meets FCC RF exposure guidelines when  
used with any belt clip, carrying case, or other accessory supplied with this product. (All necessary  
accessories are included in the package; any additional or optional accessories are not required for  
compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should  
be avoided as these might not comply with FCC RF exposure guidelines.  
Industry Canada (I.C.) Notice  
Terminal equipment  
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical  
Specifications. This is confirmed by the registration number. The abbreviation IC before the registration  
number signifies that registration was performed based on a Declaration of Conformity indicating that  
Industry Canada technical specifications were met. It does not imply that Industry Canada approved the  
equipment.  
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment  
itself. The REN assigned to each terminal equipment provides an indication of the maximum number of  
terminals allowed to be connected to a telephone interface. The termination on an interface may consist  
of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence  
Numbers of all the devices does not exceed ꢄ.  
Radio equipment  
The term IC before the radio certification number only signifies that Industry Canada technical  
specifications were met. Operation is subject to the following two conditions: (1) this device may not  
cause interference, & (ꢁ) this device must accept any interference, including interference that may cause  
undesired operation of the device. "Privacy of communications may not be ensured when using this  
telephone".  
Download from Www.Somanuals.com. All Manuals Search And Download.  
One-year Limited Warranty  
Important: Evidence of original purchase is required for warranty service.  
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden  
warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials  
& craftsmanship with only the limitations or exclusions set out below.  
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect ꢀꢁ  
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not  
maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits,  
subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired  
by someone other than an authorized Uniden service center for a defect or malfunction covered by this  
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured  
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this  
product.  
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time  
while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit &  
return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred  
by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at  
its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH  
ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF &  
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,  
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED  
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS  
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF  
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of  
incidental or consequential damages so the above limitation or exclusion may not apply to you.  
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other rights which  
vary from state to state. This warranty is void outside the United States of America & Canada.  
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in  
the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably  
in its original packaging). Disconnect the battery from the Product & separately secure the battery in its  
own separate packaging within the shipping carton. The Product should include all parts & accessories  
originally packaged with the Product. Include evidence of original purchase & a note describing the defect  
that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to  
warrantor at:  
As an Energy Star® Partner, Uniden has determined that  
Uniden America Service  
this product meets the Energy Star® guidelines for energy  
ꢃꢆ00 Amon Carter Blvd.  
efficiency. Energy Star® is a U.S. registered mark.  
Fort Worth, TX ꢆꢅꢀꢄꢄ  
®
Uniden is a registered trademark of Uniden America Corporation.  
Call waiting, CID, CIDCW, and Voice Mail are telephone line services. Your phone  
supports these services, but you have to arrange for them through your telephone provider. Contact  
your provider for details.  
The pictures in this manual are for example only. Your phone may not look exactly like the pictures.  
May be covered under one or more of the following U.S. patents:  
ꢅ,ꢅꢀꢇ,0ꢀꢄ ꢅ,ꢆꢀꢃ,ꢅꢂ0 ꢅ,ꢆꢇꢁ,0ꢈꢇ ꢅ,ꢆꢇꢇ,ꢈꢁ0 ꢅ,ꢆꢇꢇ,ꢈꢄꢂ ꢅ,ꢇꢂꢈ,ꢄꢄ0 ꢅ,ꢇꢇꢈ,ꢀꢇꢃ ꢅ,ꢈ0ꢀ,ꢁꢆꢀ ꢅ,ꢈ0ꢆ,0ꢈꢃ  
ꢅ,ꢈꢀꢃ,ꢈꢃ0 ꢅ,ꢈꢃ0,ꢇꢅꢆ ꢅ,ꢈꢄꢂ,ꢀꢀꢇ ꢆ,0ꢁꢂ,ꢀꢆꢅ ꢆ,0ꢂ0,ꢇꢀꢈ ꢆ,ꢀꢃꢅ,ꢀꢅ0 ꢆ,ꢁ0ꢂ,ꢂ0ꢆ ꢆ,ꢁ0ꢅ,ꢃ0ꢂ ꢆ,ꢂꢀ0,ꢂꢈꢇ  
Other patents pending.  
© 2009 Uniden America Corp.  
Ft. Worth, TX 76155  
Printed in Vietnam  
UNZZ01048BA(0)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson Computer Monitor 42WM03STW 0707 User Manual
Timex Watch W 199 User Manual
Toshiba Computer Drive SD M1912 User Manual
Toshiba CRT Television 32AX60 User Manual
Toshiba DVD Player P200 Series User Manual
Toshiba DVD VCR Combo SD KV540 User Manual
Toshiba Flat Panel Television 27HL95 User Manual
Uniden Two Way Radio TR620 User Manual
Verilux Indoor Furnishings VC01HH1 User Manual
Vermont Casting Gas Grill VCS3008 Series User Manual