DECT2188 Series User's Guide
What's in the box?
Telephone
cord
DECT2188 base
with answering
system
Corded
handset
Base AC
adapter
(PS-0034)
Coiled
cord
Desk stand/
wall mount
bracket
D E S K
WALL
You will also find:
DCX210
If you purchased You should
accessory
handset &
charger
Charger AC
adapter
(PS-0035)
model number:
DECT2188
have:
1 of each
DECT2188-2
DECT2188-3
DECT2188-4
DECT2188-5
DECT2188-6
2 of each
3 of each
4 of each
5 of each
6 of each
Battery
cover
Rechargeable
battery pack
(BT-1016)
If any items are missing or damaged, contact our Customer Care
Line immediately. Never use damaged products!
If You...
Contact Uniden’s... Phone Number
Customer Care
Line*
817-858-2929 or
800-297-1023
have a question or problem
need a replacement part or accessory Parts Department*
800-554-3988
need special assistance due to a
disability
Accessibility Help
Line
800-874-9314
(voice or TTY)
* During regular business hours, Central Standard Time. Visit our website for detailed business
hours.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Your Phone
Set Up the Base
Attach the stand
Before you attach the stand, you have to decide if you want the
phone to rest on a desk or hang on a wall.
For desktop use
1. Turn the stand so the
Desk
word
is right-side
DESK
up (it will be on the
right).
2. Insert the tabs into
the notches marked
A L L
W
Desk
at the top of the
DESK
base.
3. Press in on the latch
and slip it into the
notch.
DESK
For wall mount use
1. Turn the stand so the
WaLL
word
is right-
D E S K
W
ALL
side up (it will be on
the right).
2. Insert the tabs into
the notches marked
W
ALL
WaLL
at the bottom of
the base.
3. Press in on the latch
and slip it into the notch.
To remove the stand
Press in on the latch and slide it out of the notch.
Connect the corded handset
Use the coiled cord to connect the
corded handset to the connector on
the left side of the base.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
For wall mount use only
1. On the front of the base, pull
the clip (that holds the corded
handset in place) out of its slot.
2. Rotate the clip 180 degrees.
3. Flip it from front to back and slide it back into the slot.
Connect the power and telephone cords
1. Connect the base AC adapter to the AC IN 7.8V jack and the
telephone cord to the TEL LINE jack. Route the cords as shown:
For desktop use
For wall mount use
DESK
DESK
A L L
W
DESK
D E S K
W
ALL
W
ALL
2. Plug the AC adapter into a standard 120 V AC power outlet, and
connect the telephone cord to a standard telephone wall jack.
Place the phone on the wall
Place the mounting slots over the pins on the wall plate, and slide the
base down
DESK
to lock it
into place.
D E S K
W
ALL
W
ALL
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Test the Connection
Pick up the corded handset from the base. You should hear a dial
tone and the display on the base should say Talk. When you get a
dial tone, make a quick test call.
If...
Try...
the display says Check Tel Line checking the connection between
or you don't hear a dial tone
the base and the phone jack.
changing to pulse dialing (see page
4).
you keep hearing a dial tone
interference.
there's a lot of noise or static
Set Up the Accessory Handset(s)
If your phone came packaged with accessory handsets, follow the
steps below to get your cordless handsets ready for use.
Install the battery
1. Unpack all handsets, battery packs,
and battery covers. If any handset
has the battery cover already
attached, press in on the notch and
slide the cover down and off.
2. Line up the red and black wires
on the battery pack with the
label inside the handset.
3. Push the battery pack
connector in until it clicks into
place. Tug gently on the wires
to make sure the battery pack
is securely connected.
Black
Red
4. Place the cover over the battery
compartment and slide it up into
place.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the charger
1. Connect a charger AC adapter to each charger's AC IN 8V jack
and set the plug into the notch as
shown. (These adapters might already
be connected.)
2. Plug the other end of the adapter into a
V
8
N
I
C
A
standard 120V AC power outlet.
3. Place each handset in a charger with
the display facing forward. The CHArGE light should turn on.
If...
Try...
the CHArGE
light doesn't
turn on
-
-
-
reseating the handset.
checking the AC adapter connection.
seeing if the outlet is controlled by a wall
switch.
Charge all handsets completely (about 15 hours)
before using them.
Test the connection
Pick up each handset and press
and the display should say Talk. (Press
TaLk
. You should hear a dial tone,
eND
to hang up.)
If you can't get a dial tone or the handset display says Unavailable, try
Changing from Tone to Pulse Dialing
Phones can communicate with the telephone network in two different
ways: tone (DTMF) or pulse dialing. If you know your phone company
uses pulse dialing or you can't make your test call, follow these steps:
MeNu/seLeCT
1. With the phone in standby, press
on a cordless
handset. (You must use a cordless handset for this procedure.)
up
up
DoWN
MeNu/seLeCT
to highlight Global Setup, then press .
2. Use
3. Use
or
or
DoWN
MeNu/seLeCT
to highlight Dial mode, then press
.
MeNu/seLeCT
4. Highlight Pulse, then press
. The phone sounds a
confirmation tone. Try making another test call.
If you use pulse dialing and you need to send DTMF tones during a
call (if you're using an automated response system, for example),
press to temporarily switch to tone dialing. When the call ends, the
phone automatically returns to pulse dialing mode.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know Your Phone
Parts of the Base
If the key name is spelled out on the key itself, it's not labeled in the
drawing below.
PHONEBOOK/LEFT
PLAY/STOP
Hook
switch
Display
Handset
clip
UP
CALLER ID/RIGHT
DOWN
DO NOT DISTURB
DELETE
Speaker
FIND HANDSET/
INTERCOM
Twelve-key
dial pad
SPEAKER
Microphone (on back)
Base keys and how they work
Key name
What it does
(and icon)
-
-
-
While this station is ringing: mute the ringer for this call only.
During a call: mute the microphone.
While entering text: delete one character, or press & hold to
delete all the characters.
CLEAr/MUTE
-
-
In standby: open the menu.
In the menu or any list: select the highlighted item.
MENU/SELECT
rEDIAL/PAUSE
PLAY/STOP
-
-
In standby: open the redial list.
While entering a phone number: insert a 2-second pause.
-
-
-
In standby: start playing messages.
While a message is playing: stop playing messages.
In the menu or any list: exit the menu completely.
(
)
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Key name
(and icon)
What it does
-
-
In standby or during a call: open the phonebook.
In any menu or list: go up one level. (If you are already at
the top level, the phone exits the menu and returns to the
previous operation.)
PHONEBOOK/
LEFT
-
-
During text entry: move the cursor to the left.
In the first 2 seconds of a message: go to the previous
message.
(
/
)
-
Anytime after that: go to the beginning of this message.
CALLEr ID/
rIGHT
-
-
-
In standby or during a call: open the Caller ID list.
During text entry: move the cursor to the right.
While a message is playing: skip to the next message.
(
/
)
-
-
-
In standby: increase the ringer volume.
During a normal call: increase the earpiece volume.
During a speakerphone call or while a message is playing:
increase the speaker volume.
UP (
)
-
In the menu or any list: move the cursor up one line.
-
-
-
In standby: decrease the ringer volume.
During a normal call: decrease the earpiece volume.
During a speakerphone call or while a message is playing:
decrease the speaker volume.
DOWN (
ON/OFF
)
-
-
In the menu or any list: move the cursor down one line.
In standby: turn the answering system on or off.
-
-
While a message is playing: delete this message.
In standby: delete all messages.
DELETE (
)
DO NOT
DISTUrB (
-
In standby: turn the Do Not Disturb feature on or off (see
)
FLASH
BLOCK
-
-
During a call: switch to a waiting call.
While the phone is ringing: add the incoming caller ID to the
call block list (block the call).
FIND HANDSET/
INTErCOM
-
-
In standby: page a handset using the intercom.
During a call: put the call on hold & start a call transfer.
-
-
-
In standby: start a speakerphone call (get a dial tone).
During a normal call: switch to the speakerphone.
During a speakerphone call: hang up.
SPEAKEr
(
)
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR/
UP
Parts of the Handset
If the key name is spelled out
on the key itself, it's not
labeled in the drawing to the
right.
INTERCOM
CALLER ID/
RIGHT
PHONEBOOK/
LEFT
DOWN
SPEAKER
Twelve-
key dial
pad
REDIAL/
PAUSE
MESSAGES/
MUTE
Charging
contacts
Microphone
Handset keys and how
they work
Key name
What it does
(and icon)
-
-
-
In standby: increase the ringer volume.
During a call: increase the call volume.
In the menu or any list: move the cursor up one line.
UP (
)
CALLEr ID/
-
-
In standby or during a call: open the Caller ID list.
During text entry: move the cursor to the right.
rIGHT (
)
-
-
-
In standby: decrease the ringer volume.
During a call: decrease the call volume.
In the menu or any list: move the cursor down one line.
DOWN (
)
-
-
In standby: open the menu.
In the menu or any list: select the highlighted item.
During a call: hang up.
In the menu or any list: exit & go to standby.
MENU/SELECT
END
-
-
-
-
-
In standby: page another station using the intercom.
During a call: put the call on hold & start a call transfer.
While entering text: delete one character, or press & hold to
delete all the characters.
CLEAr/
INTErCOM
-
-
-
In standby or during a call: open the phonebook.
In the menu: go back to the previous screen.
During text entry: move the cursor to the left.
PHONEBOOK/
LEFT (
)
-
-
In standby: start a telephone call (get a dial tone).
During a call: switch to a waiting call.
TALK/FLASH
ꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Key name
(and icon)
What it does
SPEAKEr (
)
-
Switch a normal call to the speakerphone (& back).
rEDIAL/PAUSE
-
-
In standby: open the redial list.
While entering a phone number: insert a 2-second pause.
(
)
-
While the phone is ringing: add the incoming Caller ID
information to the call block list (block the call).
BLOCK
-
-
-
In standby: access your answering system.
During a call: mute the microphone.
While the phone is ringing: mute the ringer for this call only.
MESSAGES/
MUTE (
)
reading the Displays
On the base
On the handset
Status icons
Time
Answer ON
Status
icons
Answering
system status
12:00A
Handset #1
Day and
Message
counter
time
SUN 12:00 AM
New CID: 5
Handset
banner
Caller ID
count
Caller ID
count
The table below shows the possible icons and what they mean. Since
the icons appear based on what you're doing with the phone, you
won't ever see all of these icons at the same time.
Icon
What it means
The ringer is turned off: this station will not ring when a call
comes in.
You have a voice message waiting (see the section titled
Privacy Mode is on: no other station can join your call.
The speakerphone is on.
The microphone is muted, & the caller can't hear you.
(Handset only) T-coil mode is on. (See "Do you use a T-coil
(Handset only) The battery is 1) fully charged, 2) half charged,
3) getting low, or 4) empty.
ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
The menus are designed to be as easy as possible. Some users don't
even need the manual once they know how to perform these actions:
MENU/SELECT
Open the menu Press
.
The arrow cursor on the left side of the line shows which
UP
Move the cursor menu item is currently highlighted. Use
to move the
DOWN
cursor up &
to move it down.
MENU/
Move the cursor to highlight the option, then press
Select an option
Go up one screen Press
SELECT
.
PHONEBOOK/LEFT
.
END
PLAY/STOP
.
On the handset, press
(If you open the menu during a call, use
back out of the menu without hanging up.)
; on the base, press
Close the menu
PHONEBOOK/LEFT
to
If you don't press any
keys for thirty
seconds, the
To open the menu,
press MENU/SELECT.
To select the
highlighted
option, press
MENU/SELECT.
phone times out
and exits the
menu. (When
setting the day
and time, the time-
out period is
extended to two
minutes.)
Handset Setup
Ans. Setup
Use UP and
OR
DOWN to move
the cursor.
Day & Time
To close the menu,
press END on the
handset or PLAY/
STOP on the base.
Global Setup
Using the Base Menu
You have the following options from the base:
Reset the voice message waiting indicator to bring it back
VMWI Reset
Call Blocking
Block unwanted calls from up to 20 phone numbers and
Base Language Change the display language.
Register additional handsets to the base or re-register
a handset that you had to reset for some reason (see
Register
Handset
ꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Handset Menus
Handset Setup
You can change these settings separately for each cordless handset.
Turn on T-coil mode to reduce noise on some hearing
T-coil
Choose one of four melodies or three tones for the
handset's main ring tone. As you highlight each ring
Ringer Tones
tone, the phone plays a sample of the tone. When you
MENU/SELECT
hear the tone you want, press
.
Turn on the personal ring feature. If you have Caller ID,
this feature lets you assign special ring tones to anyone
in your phonebook: this handset will use the special
ring tone when that person calls.
Personal Ring
Autotalk
Turn on Auto Talk so you can answer the phone just by
picking up the handset from the cradle (without having
to press any buttons).
Turn on Any Key Answer so you can answer the phone
by pressing a key on the twelve-key dial pad.
Any Key Answer
Banner
Change the name used on the handset's display.
Handset Language Change the display language.
Key Touch Tone
Have the keypad sound a tone when you press a key.
Ans. Setup
This menu controls the options and settings for your answering
Day & Time
You need to set the day & time so messages get the right time stamp.
up
DoWN
MeNu/seLeCT
to choose the day of the week; press .
1. Use
&
2. Use the number keypad to enter the hour and minutes.
up
DoWN
MeNu/seLeCT
to select AM or PM; press .
3. Use
&
Global Setup
The settings on this menu apply to all cordless handsets and the
base. Before changing these settings, make sure the phone is in
standby and all handsets are within range of the base. (Only one
handset at a time can change these settings.)
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your area code so the phone hides the area code on
Area Code
Dial Mode
Change the way your phone communicates with the telephone
Set Line
Mode
Do not change this setting unless instructed to by customer
service.
Call Blocking
This menu lets you block unwanted calls from up to 20 phone
Entering Text on Your Phone
When you want to enter text into your phone (for example, a name
in the phonebook), use the twelve-key dial pad to enter the letters
printed on the number keys. Here's how it works:
The phone enters the letters in the order they appear on the key.
2
For example, if you press the number key once, the phone
2
enters the letter
A
. Press twice for
B
, and three times for
C.
If you press the key again after the last letter, the phone starts the
same letter sequence with small letters. If you press four times
2
2
in a row, the phone enters
and six times for
a
(small letter). Press five times for
b,
c
.
If you see the icon [Aa] in the display, the phone enters capital
letters first (A B C), then small letters (a b c), then the number on
the key ( ). The icon [aA] means the phone starts at the small
2
letters, so it enters small letters first, then the number on the key,
then capital letters.
The phone automatically uses a capital letter for the first letter and
any letter right after a space; all other times, it uses small letters.
If two letters in a row use the same number key, enter the first
CaLLer ID/rIGHT
letter, then use
to move the cursor to the next
position to enter the second letter.
Switch between capital
& small letters
Press
Press
.
PHONEBOOK/LEFT
CALLEr ID/rIGHT
to move the cursor to the left
to move the cursor to the right.
Move the cursor
or
POUND (#)
.
Leave a blank space
Press
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Move the cursor to the letter you want to erase and
CLEAr CLEAr/INTErCOM
CLEAr/
Erase one letter
press
(
on the handset;
MUTE
on the base).
CLEAr
Erase the entire entry Press & hold
.
Enter punctuation or a
symbol
0
Press to rotate through the available symbols.
Using Your Phone
To...
From the base
From a cordless handset
Dial the number, then pick up Dial the number, then press
make a call
answer a call
hang up
TALK/FLASH
the corded handset.
.
TALK/FLASH
Pick up the corded handset. Press
.
END
Return the handset to the
cradle.
Press
or return the
handset to the cradle.
CLEAr/MUTE
MESSAGES/MUTE
. Press
mute the
microphone
during a call
Press
again to turn the microphone again to turn the microphone
back on. back on.
. Press
Press
FIND HANDSET/INTErCOM
If the call is on hold for 5 minutes, it will be disconnected.
CLEAr/INTErCOM
.
Press
. Press
put a call on
hold
return to a call Pick up the handset or press
TALK/FLASH
Press
.
SPEAKEr
on hold
.
mute the ringer While the phone is ringing,
While the phone is ringing,
CLEAr/MUTE
MESSAGES/MUTE
.
for this call only press
.
press
Using the Speakerphone
Both the handset and the base have a speakerphone. To use the
speaker
base speaker, press
instead of using the corded handset. To
speaker
TaLk/FLasH
use the handset speaker, press
instead of
.
To...
From the base
From a handset
SPEAKEr
SPEAKEr
SPEAKEr
SPEAKEr
SPEAKEr
SPEAKEr
make a call: Dial the number, then Press
.
.
.
Press
Press
Press
.
.
.
answer a call
Press
Press
switch a call to the speakerphone
Pick up the
corded handset.
SPEAKEr
switch back to the earpiece
hang up a speakerphone call
Press
Press
.
SPEAKEr
END
.
Press
.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Volume
You can set the volume of the ringer, the earpiece, and the
speakerphone separately for the base and each cordless handset.
up
DoWN
For each item, press
to make it louder or
to make it softer.
The available volume levels and how change them are listed below:
Change the When
On the base
On a handset
ringer
volume
the phone is in
standby
select Off, Low,
select Off, Low,
Medium, or High Medium, or High
earpiece
volume
you are on a normal choose one of 6
choose one of 6
volume levels
call
volume levels
you use the speaker-
phone for a call or
getting messages
speaker
volume
choose one of 10
volume levels
choose one of 6
volume levels
Using the redial List
The phone saves the last 5 numbers you dial on each station. To
reDIaL/pause
up
DoWN
and to scroll
open the redial list, press
; use
pHoNebook/LeFT
through the list. To close the list, press
. With the
phone in standby, open the list and find the number you want. Then:
TALK/FLASH;
on the base, pick up the corded handset.
On the handset, press
to redial the selected number
to delete the number
MENU/SELECT
Press
& select Delete Entry
.
MENU/SELECT
to save it to the phonebook Press
& select Store Into Pb
.
Using Caller ID and Call Waiting
You have to subscribe to Caller ID, Call Waiting, and Caller ID
on Call Waiting services to use the features described in this
section: contact your telephone provider for more information.
When a call comes in, the phone displays the caller’s number and
name (if available). The phone saves the information for the last 30
received calls to the CID list. When it's in standby, the phone displays
how many calls came in since the last time you checked the CID list.
CALLEr ID/rIGHT
Open the CID list
Press
.
DOWN
oldest. Press
Scroll through the CID Press
to scroll through the list from newest to
UP
to scroll from oldest to newest.
list
PHONEBOOK/LEFT
.
Close the CID list
Press
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Dialing from the Caller ID list
1. Find the entry you want to dial.
2. If the number is a toll or long distance call, but there's no 1 at the
front of the CID record, press to add the 1.
TaLk/FLasH
3. On the handset, press
pick up the corded handset.
to dial the number. On the base,
TaLk/FLasH
(You can also press
or pick up the corded handset before
opening the CID list. Find the number you want to dial, then press
MeNu/seLeCT
.)
Caller ID menu options
With the phone in standby, open the CID list and find the number you
MeNu/seLeCT
want. Press
to open the Caller ID menu; choose one of
these options:
Delete Entry
Erase this Caller ID number.
Add this number to this station's phonebook. The phone
prompts you to enter a name & edit the number; cordless
handsets also prompt you to choose a personal ring.
Store Into Pb
Erase this station's CID list. (This does not affect the CID
lists saved on any other stations.)
Delete All
(Handset only) Add this number to your call block list (see
Add Call Block
Using Call Waiting
If you get a Call Waiting call, the phone sounds a tone and displays
FLasH TaLk/
any CID information received for the waiting call. Press
(
FLasH
on a handset) to switch between your current call and the
waiting call; remember, each time you switch, there is a short pause
before you're connected to the other caller.
Using Seven-Digit Dialing
If you can make a local call by dialing only seven digits instead of ten,
you can tell the phone to hide your local area code in the CID list.
Do not enter an area code if your phone company requires ten-
digit dialing. You might not be able to dial from the CID list.
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. With the phone in standby, open the menu and select Global
Setup, then select Area Code
.
0 - 9
2. Use the number keypad ( ) to enter your three-digit area code.
MeNu/seLeCT
3. Press
when you’re finished.
The phone uses the programmed code as a filter. When calls
come in, the phone compares the area code to the programmed
one. If they match, the phone hides the area code in the CID list.
#
While reviewing the list, press to toggle the area code off & on.
Using the Phonebook
Each station can store up to 70 entries in its phonebook.
PHONEBOOK.
Open/close the phonebook Press
DOWN
from A to Z or
Press
to scroll through the phonebook
Scroll through the entries
UP
to scroll from Z to A.
Jump to entries that start
with a certain letter
Press the number key corresponding to the
letter you want to jump to.
1. Find the entry you want to dial.
Dial an entry
TALK/FLASH
. On the
2. On a handset, press
base, pick up the corded handset.
Phonebook menu options
Open the phonebook with the phone in standby, then press
MeNu/
seLeCT
to open the phonebook menu. Choose one of these options:
Add an entry to your phonebook. The phone will prompt you to
enter the name & phone number. (Cordless handsets will also
prompt you to choose a personal ring.)
Create
New
Copy
All
Copy the whole phonebook to another station. (You must have at
least one accessory handset to use this multi-station feature.)
Delete Erase all the entries in this station's phonebook. (This does not
All affect the entries saved on any other stations.)
Phonebook entry options
With the phone in standby, open the phonebook and find the entry
MeNu/seLeCT
you want. Press
to open the individual phonebook entry
menu. Choose one of these options:
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit this entry. The phone will prompt you to enter the name &
phone number. (Cordless handsets will also prompt you to choose
a personal ring.)
Edit
Copy this entry to another station. (You must have at least one
accessory handset to use this multi-station feature.)
Copy
Delete Erase this entry.
Chain Dialing
If you often have to enter a series of digits or a code number
during a call, you can save that code number to a phonebook
entry and use the phonebook to send the code number.
Enter the code number (up to 20 digits) into the phonebook just
like a regular phonebook entry. Be sure to enter the code number
into the phonebook exactly as you would enter it during a call.
When you hear the prompt that tells you to enter the number, open
the phonebook and find the entry that contains your code number.
MeNu/seLeCT
Press
to transmit the code. The phone transmits the
code number exactly as you entered it in the phonebook. Or, if you
pHoNebook/LeFT
change your mind, use
to close the phonebook.
Finding a Lost Handset
With the phone in standby, press
FIND HaNDseT/INTerCoM
on the base.
Select the handset you want to find, or select All to page all handsets
at the same time. The paged handset(s) will beep for 1 minute or until
FIND HaNDseT/INTerCoM
TaLk/FLasH
you press
again or press
followed by
eND
on the handset.
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Multi-station Features
The expandable base works together with the accessory handsets
to give you some useful multi-station features. (A station can be any
cordless handset or the base.) You must have at least one accessory
handset to use the features in this section.
Expanding Your Phone
Your base supports a total of six DCX210 accessory handsets,
including any that were supplied with your phone.
Your base might be compatible with other Uniden accessory
handsets: please visit our website for a list of compatible handsets.
Accessory handsets must be registered to the base before you
can use them. Handsets that aren't registered display a Handset
not registered message. For instructions on registering handsets to
Any accessory handsets that came packaged with the base are
already registered to that base for you.
If a handset was previously registered to a base, you have to reset
Using Conference Calling
Outside call
When an outside call comes in, the base
and two cordless handsets can join in a
conference call with the outside caller. To
join the call, just pick up the base corded
Handset #2
TaLk/FLasH
handset or press
on a cordless
Base
speakerphone
or corded handset
handset. To leave the conference call,
hang up normally; the other station
Handset #1
remains connected to the call. (You can also use the speakerphone
for a conference call, just like you can with a normal call.)
Using Privacy Mode
You can prevent other stations from joining a call. Start your call as
MeNu/seLeCT
usual, then press
: the display shows Call Privacy. Press
MeNu/seLeCT
again to turn privacy mode on (you'll see a in the
display). When you hang up, privacy mode turns off automatically.
As long you have privacy mode on, no other stations can interrupt
your call. To allow another station to join the call, just turn privacy
MeNu/seLeCT
mode off by repeating the process above (press
twice).
ꢀꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Call Transfer
To...
From the base
From a cordless handset
FIND HANDSET/INTErCOM
1. Press
put the call on hold.
CLEAr/INTErCOM
to 1. Press to
put the call on hold.
2. Select the station you want to transfer the call to, or select
transfer a
call
All to page all the stations at the same time.
When the other station accepts the call, you'll be disconnected,
but you can join the call again.
SPEAKEr
TALK/FLASH
Press to return to
the call.
cancel a
transfer
Press
call.
to return to the
1. To answer the page & speak to the transferring station,
accept a
transferred
call
CLEAr/INTErCOM.
pick up the corded handset.
2. To accept the call,
press
press
SPEAKEr
TALK/FLASH
.
press
.
Using the Intercom
Here are some things you need to know about using the intercom:
Whenever the phone is in standby, you can make an intercom call
between stations without using the phone line.
You can make an intercom call from any station, but only two
stations can be in an intercom call at any time.
If an outside call comes in during an intercom call, the phone shows
the CID information. If the other station hasn't answered the page,
the phone cancels the page so you can answer the incoming call.
To...
From the base
From a cordless handset
FIND HANDSET/INTErCOM
CLEAr/INTErCOM
.
1. Press
.
1. Press
make an intercom
page
2. Select the station you want to talk with, or select All to
page all the stations at the same time.
FIND HANDSET/INTErCOM.
END
.
cancel a page
Press
Press
FIND HANDSET/INTErCOM
pick up the corded handset.
CLEAr/INTErCOM
or
answer an
intercom page
Press
or Press
TALK/FLASH
.
leave an intercom
call
FIND HANDSET/INTErCOM.
END
.
Press
Press
Press
answer an outside
call during an
intercom call
SPEAKEr.
TALK/FLASH
.
Press
ꢀꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Special Features
Using Your Phone During a Power Failure
Because it includes a corded handset, your phone can perform
several of its functions during a power failure. The following features
will operate during a power failure (all other features are disabled):
Making and receiving calls with the base corded handset.
Changing the volume on the corded handset.
Using Call Waiting on a base corded handset call.
Entering pauses when dialing from the base corded handset.
While the power is out, the base uses a special ringer; you
cannot adjust the volume of this ringer.
Using Do Not Disturb
The Do Not Disturb or DND feature turns off the ringers of the
base and all handsets at the same time.
Do NoT DIsTurb
With the phone in standby, press and hold
on the
base. The phone automatically turns on the answering system and
shows Do Not Disturb in the display on all stations.
Do NoT DIsTurb
again.
To cancel, press
If you turn the answering system off while DND is on, the phone
turns off DND along with the answering system.
Using Call Block
If you subscribe to Caller ID, you can save phone numbers to the call
block list. When a call comes in, the phone compares the received
phone number to the numbers on the call block list. If the phone
number is on the list, the phone replaces the caller's name with Call
Blocked and disconnects the call. (The caller hears a reject tone.)
The call block list holds 20 entries, and all stations share the same
list. You can add entries through the Call Blocking menu, by selecting
Add Call Block in the CID menu, or by blocking incoming calls. (Only
one station can edit the call block list at a time.)
Blocking incoming calls
When the phone rings, wait until the display shows the Caller ID
information (usually after the second ring). If you want to block the
ꢀꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
bLoCk
call and add this number to the call block list, press
. When the
MeNu/seLeCT
bLoCk
phone asks you to confirm, press
or
.
blocking an incoming call from an "unknown" or "private"
number is the same as selecting Unknown Number or Private
Number from the Call Blocking menu.
Call Blocking menu options
With the phone in standby, open the menu and select Call Blocking
Choose one of these options:
.
View Number See the numbers on your call block list.
(Handset only) Add an entry to your call block list. The phone
will prompt you to enter a name & phone number.
Create New
Private
Number
(Handset only) Block all calls from numbers reported by CID
as "Private." (This does not count as one of the 20 entries.)
Unknown
Number
(Handset only) Block all calls from numbers reported by CID
as "Unknown". (This does not count as one of the 20 entries.)
Call block entry options
With the phone in standby, open the call block list and find the entry
MeNu/seLeCT
you want. Press
to open the individual entry menu.
Choose one of these options:
(Handset only) Edit this entry. The phone will prompt you to edit
the name & phone number.
Edit
Delete Erase this entry from the list & allow calls from this number.
Using Voice Message Notification
This feature supports Frequency-shift keying (Fsk) message
notification. Contact your voice mail provider for more details.
If you subscribe to a voice mail service, your phone
can notify you when you have a new message
waiting. When you have new messages, the voice
message icon
(
) appears in the display, and the
new message light (at the top of the handset) blinks.
Resetting the voice message indicator
If the voice message icon remains after you check
your messages, you can reset it. From the base, open the menu and
select VMWI Reset. Select Yes to reset the indicator.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Answering System
Setting Up Your Answering System
You can set up your answering system from any handset.
To...
Follow these steps
Your greeting can be between 2 seconds and 30 seconds
long. If you don't record an outgoing message, the system
uses a pre-recorded greeting: Hello, no one is available to
take your call. Please leave a message after the tone.
MESSAGES/MUTE
1. Press
to access the answering system. Wait
Record your
personal
5
until the system finishes its announcements, or press
(STOP)
to skip them.
outgoing
8
2. Press
.
message or
greeting
3. Wait for the system to say "Record greeting," then begin
speaking.
8
4. When you're finished, press to stop recording. The
system plays back your new greeting.
END
5. To keep this greeting, press
. To re-record it, go back to
step 2.
MESSAGES/MUTE
1. Press
to access the answering system. Wait
Switch
5
until the system finishes its announcements, or press
between the
pre-recorded
greeting &
your own
greeting
(STOP)
to skip them.
6
2. Press
.
The system plays back the greeting it is currently
using.
6
3. Press again to switch greetings.
1. Switch to your personal greeting following the steps above.
2. While the system is playing back your greeting, press .
Delete your
greeting
4
Ans. Setup menu options
You can change the answering system options from any handset.
Just open the menu and select Ans. Setup
.
Enter a 2-digit PIN so you can access your answering
Security Code
Ring Time
Set the number of rings (
2
,
4
, or 6) before the answering
system answers the phone. Choose Toll Saver (TS) to
have the system pick up after 2 rings if you have new
messages or after 4 rings if you don't.
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the amount of time callers have to leave a message,
Record Time
either
1
minute or
4
minutes. Choose Announce Only if
you don't want the system to let callers to leave a message.
Have the system beep every 15 seconds when you have
a new message; the beeping stops when you listen to all
your new messages. (To mute the alert without listening to
your messages, press any key on the base.)
Message Alert
Ans. Language Change the language of the system's voice prompts.
Turn on the call screen feature so you can hear callers as
Call Screen
Turn your answering system on or off. (To turn your
Ans. On/off
ON/OFF
system on or off from the base, just press
.)
Getting Your Messages
Accessing your answering system from a handset
You can access your system from a handset whenever the phone is
in standby.
Press MESSAGES/MUTE to start
remote operation mode.
1:Repeat 3:Skip
2:Play 4:Delete
Use PHONEBOOK/
LEFT to go to the
previous option.
6:SelectGreeting
5:Stop
[ / /select]
8:RecNewGreeting
Use CALLER ID/
RIGHT to go to the
next option.
Press MENU/
SELECT to choose
the current option.
Press END to exit remote
operation mode.
During remote operation, the phone beeps to let you know it's
waiting for your next command.
You can press the number key next to the commands instead of
scrolling through them.
If you don't press any keys for 30 seconds, the phone returns to
standby.
Only one handset can access the system at a time.
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to operate your answering system
From a handset (remote
operation)
To...
From the base
PLAY/STOP
MESSAGES/MUTE
.
Press
Press
The system announces the number of new & old messages,
then plays the first new message followed by the day & time
it was received. Then the system plays the new messages
in the order they were received.
play new
messages
restart the
current message
PHONEBOOK/LEFT
1
Press
.
Press or select 1:Repeat
.
PHONEBOOK/LEFT
repeatedly until you hear the repeatedly until you hear the
message you want to replay. message you want to replay.
1
Press
Press or select 1:Repeat
replay previous
messages
CALLEr ID/rIGHT
3
skip a message Press
.
Press or select 3:Skip.
While the message is
While the message is playing,
delete a message
DELETE
4
playing, press
.
press or select 4:Delete
.
With the phone in standby,
DELETE
delete all of your press
. When the
Not available.
messages
system asks you to confirm,
DELETE
press
again.
After the system plays the new messages,
play old
messages
PLAY/STOP
PLAY/STOP
2
press
Press
again.
press or select 2:Play.
end the
operation
END
.
.
Press
Screening Your Calls
Another feature your answering system gives you is call screening.
While the system is taking a message, you can hear the caller on the
base speaker (if you turn on Call Screen) or from a handset.
To...
From the base
From a handset
hear the caller
Just listen to the caller over
MESSAGES/MUTE
Press
.
leaving a message the speaker.
TALK/FLASH
.
answer the call
mute the call screen
without answering
Pick up the corded handset. Press
Press
END
or return the
CLEAr/MUTE
Press
.
handset to the cradle.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
If you mute the call screen, the system continues taking the
message: it just stops playing through the speaker.
Only one handset at a time can screen calls. If another handset is
screening the call, the handset beeps and returns to standby.
Using the System While You're Away from Home
You can also operate your answering system from any touch-tone
phone. Before you can use this feature, you have to program a
security code.
Programming a security code
1. With the phone in standby, open the menu from any handset.
2. Select Ans. Setup, then select Security Code
.
3. Use the number keypad to enter a two-digit security code (01 to
MeNu/seLeCT
99). Press
when you’re finished.
remember to make a note of your new security code!
Dialing in to your system
1. Call your telephone number and wait for the system to answer. (If
your answering system is off, it will answer after about ten rings
and sound a series of beeps instead of your greeting.)
0
2. During the greeting (or beeps), press and immediately enter
your security code. (You have 3 tries to enter you security code:
if you enter it wrong 3 times, the system hangs up and returns to
standby.)
3. The system announces the current time, the number of messages
stored in memory, and a help prompt. Then it starts beeping
intermittently to let you know it's waiting for your command.
4. When you hear the intermittent
0-1 Repeat message
beeping, enter a command from the
chart to the right.
0-2 Play message
0-3 Skip message
If you don't press any keys for 15
seconds, the phone will hang up and
return to standby.
0-4 Delete message
0-5 Stop playback
0-6 Turn the system on
0-9 Turn the system off
1-0 Hear help prompts
ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
If you have any trouble with your phone, try these simple steps first.
If you still have a question, call our Customer Care Line listed on the
front cover.
If…
Try…
-
-
Checking the telephone cord connection.
Disconnecting the base AC adapter. Wait a few
minutes, then reconnect it.
No stations can make
or receive calls.
One cordless handset
can’t make or receive
calls.
-
-
Moving the handset closer to the base.
Resetting the handset.
-
-
Making sure the ringer is turned on.
Making sure Do Not Disturb is turned off.
A station can make
calls, but it won’t ring.
-
Making sure you using the corded handset on the
base.
Checking the telephone cord connection.
I can't make or receive
calls while the power
is out.
-
-
-
Charging the battery for 15-20 hours.
Checking the battery pack connection.
A cordless handset's
display won't turn on.
-
-
-
Charging the battery for 15-20 hours.
Checking the battery pack connection.
Resetting the handset.
A cordless handset is
not working.
-
-
-
Moving the handset closer to the base.
Seeing if another station has Privacy Mode on.
Making sure the base is plugged in.
A cordless handset
says Unavailable
.
-
-
-
Letting calls ring at least twice before answering.
Seeing if the call was placed through a switchboard.
Checking with your telephone service provider to
make sure your Caller ID service is active.
No stations will
display any Caller ID
information.
-
-
Making sure you entered the correct area code. If
you have to dial all 10 digits, you need to delete the
You may have to change the line mode. Contact
customer service for more information.
I can't dial from the
Caller ID list.
Caller ID displays
briefly & then clears.
I can’t transfer calls.
-
-
Resetting all the handsets.
Making sure both handsets are registered to this
base.
I can’t get two cordless
handsets to talk to the
caller.
-
Making sure no station is in Privacy Mode.
ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
If…
Try…
The phone keeps
ringing if I answer on
an extension.
-
You may have to change the line mode. Contact
customer service for more information.
-
-
Making sure the answering system is turned on.
Making sure the base AC adapter is not plugged into
an that's controlled by a wall switch.
The answering system
does not work.
-
-
Making sure the Record Time is not set to
The answering
system won't record
messages.
Announce Only
.
Deleting messages (the memory may be full).
-
-
Making sure no other handset is using the system.
Making sure the phone is in standby.
A handset can't access
the answering system.
My outgoing message
is gone.
-
Seeing if there was a power failure. You may have to
re-record your personal outgoing message.
-
-
Making sure call screening is turned on.
Changing the base speaker volume.
I can’t hear the base
speaker.
-
The incoming messages may be too long. Remind
callers to leave a brief message.
Deleting messages (the memory may be full).
Messages are
incomplete.
-
-
The system keeps
recording if I answer
on an extension.
You may have to change the line mode. Contact
customer service for more information.
-
-
Seeing if there are 6 handsets registered to this base.
Resetting the handset.
I can't register a
handset.
Weak or Hard To Hear Audio
If a caller’s voice sounds weak or soft, the signal might be blocked by
large metal objects or walls; you might also be too far from the base,
or the handset’s battery may be weak.
Try moving around while you’re on a call or moving closer to the
base to see if the sound gets louder.
Make sure the handset’s battery is fully charged.
Try adjusting the earpiece volume or the audio tone (see below).
Adjust the audio tone
During a call, open the menu and select Audio Tone. Choose one of
the three audio tone options: High Tone Natural Tone (recommended
,
for hearing aid users), or Low Tone. You may have to experiment to
figure out which audio tone works best for you.
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise or Static On The Line
Interference is the most common
cause of noise or static on a
cordless phone. Here are some
common sources of interference:
Do you use a T-Coil hearing aid?
If you have a hearing aid
equipped with a telecoil (T-coil)
feature, the interaction between
the hearing aid & digital cordless
phones can cause noise in the
handset. If you have a T-coil
hearing aid & you have problems
with noise on the line, try turning
on T-coil mode. Open the menu.
Select Handset Setup, then
electrical appliances, especially
microwave ovens
computer equipment, especially
wireless LAN equipment and
DSL modems
select T-coil
.
radio-based wireless devices,
such as room monitors,
Using T-coil mode can shorten
the handset’s talk time; make
sure to watch the battery status
and keep the battery charged.
wireless controllers, or wireless
headphones or speakers
large florescent light fixtures
(especially if they give off a buzzing noise)
other services that use your phone line, like alarm systems,
intercom systems, or broadband Internet service
Here are some hints for when the static is...
on 1 handset or in 1 location:
on all handsets or in all locations:
-
Check nearby for one of the
-
Check near the base for the source
of interference.
Try moving the base away from a
suspected source, or turn off the
source if possible.
If the base has an adjustable
antenna, try raising the antenna so
it stands straight up.
If you have any service that uses the
phone line, you might need a filter
(see below).
common interference sources.
Try moving the handset away from
a suspected source, or try moving
the suspected source so it’s not
between the handset & the base.
Try moving closer to the base.
There is always more noise at the
edges of the base's range. If the
handset displays an Out of Range
message, you need to move closer
to the base.
-
-
-
-
-
Installing a line filter or DSL filter
Sometimes, broadband Internet services that use the telephone line
can interfere with phones. One of these services−DSL−often causes
static on telephones. A DSL filter or telephone line filter usually solves
ꢁꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
this problem. The technician who installed your DSL service might
have left some filters for you; if not, call your DSL provider or look in
any electronics store.
Telephone
wall jack
Plug the DSL filter into the telephone wall
jack and plug your phone’s base into the
filter. Make a test call to make sure the
Telephone
cord
noise is gone.
DSL filter
resetting and registering Handsets
If you are having trouble with a cordless handset or if you want to
replace one, you need to clear the registration information from the
base and the handset:
Do you have the base the handset is registered to?
Yes
No
END
#
END
#
1. Press & hold
and until the
1. Press & hold
and until the
System Reset menu appears
(about 5 seconds).
System Reset menu appears
(about 5 seconds).
2. Select Deregister HS. The display 2. Select Base Unavailable
.
3. When the phone asks you to
confirm, select Yes. The handset
deletes its own link without
contacting the base.
lists all registered handsets.
3. Select the handset you want to
reset.
4. When the phone asks you to
confirm, select Yes. The handset
clears its information from the base
& deletes it own link to the base.
When you reset a handset (or if you buy a new one), that handset
displays a Handset Not Registered message. If you see this message
on a handset, you need to register it to a base before you can use it.
Registering a handset
1. On the base, open the menu and select Register Handset. The
display should say Handset Registering
.
pouND (#)
2. On the handset you want to register, press and hold
until
the handset display says Handset Registering (about 2 seconds).
3. In about 30 seconds, the handset display should say Registration
TaLk/FLasH
Complete. Press
and make sure you get a dial tone.
ꢁꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
If...
Try...
-
-
you don't hear a dial tone
the display says Registration Failed
Making sure the handset is fully
charged, then start over at step 1.
To register a handset to a different base, see the section
"expanding Your phone" in the user's guide for the other base.
Handling Liquid Damage
Moisture and liquid can damage your cordless phone.
If the handset or base is exposed to moisture or liquid, but only the
exterior plastic housing is affected, wipe off the liquid, and use as
normal.
If moisture or liquid has entered the plastic housing (i.e. liquid can
be heard in the phone or liquid has entered the handset battery
compartment or vent openings on the base), follow these steps:
Handset
Base
1. Remove the battery cover &
disconnect the battery.
2. Let dry for at least 3 days with the
battery disconnected and the cover
off for ventilation.
1. Disconnect the AC adapter to cut
off the power.
2. Disconnect the telephone cord.
3. After the handset dries, reconnect 3. Let dry for at least 3 days before
the battery pack and replace the
cover. Recharge the battery fully
(15-20 hours) before using.
reconnecting.
IMporTaNT: You must unplug the telephone line while
recharging the battery pack to avoid charge interruption.
CAUTION! DO NOT use a microwave oven to speed up
the drying process. This will cause permanent damage
to the handset, base and the microwave oven.
ꢁꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Terms Used In This Guide
Accessory
Handset
An extra handset that can register to and be used with an expandable phone base. All
accessory handsets must be registered to a base.
The main part of the phone. It connects to your phone line and lets you make and receive
calls. Most bases also have a cradle to store a handset.
Base
CIDCW
(CID on Call Waiting.) A service that shows CID for calls that come in during another call.
Call Waiting A service that lets you receive calls while you are on another call.
Caller ID
Charger
(Also called CID.) A service that shows the name and number of incoming callers.
A cradle that stores and charges a handset but doesn’t connect to the phone line.
The part of the phone that stores a handset. While in a cradle, a handset is always in
standby, and any keys are locked.
Cradle
During a call The station is currently on a call or has activated a dial tone.
ꢀ) A cordless handset that you use to dial the phone and talk to callers.
Handset
ꢁ) A corded handset that attaches to a base with a coiled cord.
The phone is inactive: there is no dial tone, no station is on a call or listening to
In standby
messages.
Station
Any handset or the base.
Specifications
Base
Part number PS-00ꢂꢃ
Charger
PS-00ꢂꢄ
ꢀꢁ0V AC, ꢅ0 ꢀꢁ0V AC, ꢅ0
Use only the supplied AC adapters.
Be sure to use the proper adapter for the
base & any chargers.
Do not place the power cord where it
creates a trip hazard or where it could
become chafed & create a fire or
electrical hazard.
AC
adapter
Input voltage
Hz
Hz
ꢇV AC @
ꢂ00mA
Output
voltage
ꢆ.ꢇV AC @
ꢃꢄ0mA
Part number BT-ꢀ0ꢀꢅ
Capacity ꢄ00mAh, ꢁ.ꢃV DC
Battery
pack
Do not place the base in direct sunlight or
subject it to high temperatures.
Battery Information
Fully charged, the battery should provide about ꢀ0 hours of talk time and about ꢆ days of standby
time. For best results, return the handset to the cradle after each call to keep it fully charged.
Keep an eye on the battery status icon. When the battery gets too low, the handset shows a low
battery alert. If you hear a strange beep during a call, check the display: if you see the low battery
alert, finish your conversation as quickly as possible and return the handset to the cradle. If the
handset is in standby, none of the keys will operate.
With normal use, the battery should last about one year. Replace the battery when the talk time
becomes short even when the battery is charged. To buy a replacement battery, call the Parts
Department listed on the front cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rechargeable Nickel-Metal-Hydride Battery Warning
CAUTION! Risk of explosion if battery is replaced by an incorrect type!
Dispose of used batteries according to the instructions. Do not open or
mutilate the battery. Disconnect the battery before shipping this product.
This equipment contains a rechargeable Nickel-Metal-Hydride battery.
The rechargeable batteries contained in this equipment may explode if disposed of in a fire.
Nickel is a chemical known to state of California to cause cancer.
Do not short-circuit the battery.
Do not charge the rechargeable battery pack used in this equipment with in any charger other
than the one designed to charge this battery pack as specified in the owner's manual. Using
another charger may damage the battery pack or cause the battery pack to explode.
Rechargeable Batteries Must Be Recycled or Disposed of Properly.
Uniden works to reduce lead content in PVC coated cords in our products &
accessories.
Warning! The cords on this product and/or accessories contain
lead, a chemical known to the State of California to cause birth
defects or other reproductive harm. Wash hands after handling.
Compliance information
FCC Part 68 information
This equipment complies with Part 68 of the FCC rules & the requirements adopted by the
ACTA. On the bottom of this equipment is a label that contains, among other information,
a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be
provided to the phone company.
An applicable Universal Service Order Codes (USOC) certification for the jacks used in this
equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal
equipment. A plug & jack used to connect this equipment to the premises wiring & telephone
network must comply with the applicable FCC Part 68 rules & requirements adopted by
the ACTA. A compliant telephone cord & modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See installation
instructions for details.
The REN is used to determine the number of devices that may be connected to a phone line.
Excessive RENs on a phone line may result in devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain
of the number of devices that may be connected to a line, as determined by the total RENs,
contact the telephone provider. The REN for this product is part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone company will notify you
in advance that temporary discontinuance of service may be required. But if advance notice
isn't practical, the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary. The
telephone company may make changes in its facilities, equipment, operations or procedures
that couldDaoffwecntlothaed ofrpoemraWtiownwo.Sfothmeaenquualisp.mcoemnt..AIflltMhiasnhuaaplspeSnesartchheAtenldepDhoownnelocaodm. pany
will provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery replacement section); otherwise do
not substitute or repair any parts of the device except as specified in this manual. Connection
to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information. This equipment is hearing aid
compatible.
Should you experience trouble with this equipment, please contact a factory service center or
other authorized service agent. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the equipment until the problem is
resolved.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting
from lightning strikes, are very destructive to telephone equipment connected to AC power
sources. To minimize damage from these types of surges, a surge arrestor is recommended.
Changes or modifications to this product not expressly approved by the manufacturer, or
operation of this product in any way other than as detailed by the owner’s manual, could void
your authority to operate this product.
FCC Part 15 information
This device complies with part ꢀꢄ of the FCC rules. Operation is subject to the following two
conditions: (ꢀ) This device may not cause harmful interference, & (ꢁ) This device must accept
any interference received, including interference that may cause undesired operation. Privacy
of communications may not be ensured when using this phone.
FCC PART 15.105(b): Note: This equipment has been tested & found to comply with the limits
for a Class B digital device, pursuant to part ꢀꢄ of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses & can radiate radio frequency energy &, if not installed & used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off & on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
To insure the safety of users, the FCC has established criteria for the amount of radio
frequency energy various products may produce depending on their intended usage. This
product has been tested & found to comply with the FCC's exposure criteria. For body worn
operation, the FCC RF exposure guidelines were also met when used with the Uniden
accessories supplied or designed for this product. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines & should be avoided.
Download from Www.Somanuals.com. All Manuals Search And Download.
The antenna(s) used for the base-unit must be installed to provide a separation distance of
at least ꢁ0 cm from all persons & must not be collocated or operated in conjunction with any
other antenna or transmitter.
If your home has wired alarm equipment connected to a phone line, be sure that installing the
system does not disable your alarm equipment. If you have questions about what will disable
alarm equipment, contact your telephone company or a qualified installer.
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number. The abbreviation IC
before the registration number signifies that registration was performed based on a Declaration
of Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on
the equipment itself. The REN assigned to each terminal equipment provides an indication
of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed ꢄ.
Radio equipment
The term IC before the radio certification number only signifies that Industry Canada technical
specifications were met. Operation is subject to the following two conditions: (1) this device
may not cause interference, & (ꢁ) this device must accept any interference, including
interference that may cause undesired operation of the device. "Privacy of communications
may not be ensured when using this telephone".
One-year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY:
Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from
defects in materials & craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further
effect ꢀꢁ months after the date of original retail sale. The warranty is invalid if the Product is
(A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone other than an authorized Uniden
service center for a defect or malfunction covered by this warranty, (E) used in any conjunction
with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed
or programmed by anyone other than as detailed by the owner's manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty
at any time while this warranty is in effect, warrantor will either, at its option, repair or replace
the defective unit & return it to you without charge for parts, service, or any other cost (except
shipping & handling) incurred by warrantor or its representatives in connection with the
Download from Www.Somanuals.com. All Manuals Search And Download.
performance of this warranty. Warrantor, at its option, may replace the unit with a new or
refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE
WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER
WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR
ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR
PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow
this exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other
rights which vary from state to state. This warranty is void outside the United States of America
& Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the
instructions in the owner's manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging). Disconnect the battery from the Product
& separately secure the battery in its own separate packaging within the shipping carton. The
Product should include all parts & accessories originally packaged with the Product. Include
evidence of original purchase & a note describing the defect that has caused you to return it.
The Product should be shipped freight prepaid, by traceable means, to warrantor at:
As an Energy Star® Partner, Uniden has
determined that this product meets the
Energy Star® guidelines for energy efficiency.
Energy Star® is a U.S. registered mark.
Uniden America Service
ꢃꢆ00 Amon Carter Blvd.
Fort Worth, TX 76155
®
Uniden is a registered trademark of Uniden America Corporation.
Call waiting, CID, CIDCW, and Voice Mail are telephone line services. Your phone
supports these services, but you have to arrange for them through your telephone provider.
Contact your provider for details.
The pictures in this manual are for example only. Your phone may not look exactly like the
pictures.
May be covered under one or more of the following U.S. patents:
ꢄ,ꢇ0ꢀ,ꢃꢅꢅ
ꢄ,ꢈꢂ0,ꢆꢁ0
ꢅ,ꢁꢄꢂ,0ꢇꢇ
ꢅ,ꢆꢇꢇ,ꢈꢁ0
ꢅ,ꢈꢃ0,ꢇꢅꢆ
ꢆ,ꢂꢀ0,ꢂꢈꢇ
ꢄ,ꢇꢁꢄ,ꢀꢅꢀ
ꢄ,ꢈꢅ0,ꢂꢄꢇ
ꢅ,ꢂꢀꢃ,ꢁꢆꢇ
ꢅ,ꢆꢇꢇ,ꢈꢄꢂ
ꢅ,ꢈꢄꢂ,ꢀꢀꢇ
ꢄ,ꢇꢅꢃ,ꢅꢀꢈ
ꢄ,ꢈꢇꢆ,ꢂꢂ0
ꢅ,ꢂꢁꢀ,0ꢅꢇ
ꢅ,ꢇꢂꢈ,ꢄꢄ0
ꢆ,0ꢁꢂ,ꢀꢆꢅ
ꢄ,ꢇꢈꢂ,0ꢂꢃ
ꢅ,0ꢃꢃ,ꢁꢇꢀ
ꢅ,ꢃꢀꢇ,ꢁ0ꢈ
ꢅ,ꢇꢇꢈ,ꢀꢇꢃ
ꢆ,0ꢂ0,ꢇꢀꢈ
ꢄ,ꢈꢀꢁ,ꢈꢅꢇ
ꢅ,0ꢆ0,0ꢇꢁ
ꢅ,ꢅꢀꢇ,0ꢀꢄ
ꢅ,ꢈ0ꢀ,ꢁꢆꢀ
ꢆ,ꢀꢃꢅ,ꢀꢅ0
ꢄ,ꢈꢀꢄ,ꢁꢁꢆ
ꢅ,0ꢆꢅ,0ꢄꢁ
ꢅ,ꢆꢀꢃ,ꢅꢂ0
ꢅ,ꢈ0ꢆ,0ꢈꢃ
ꢆ,ꢁ0ꢂ,ꢂ0ꢆ
ꢄ,ꢈꢁꢈ,ꢄꢈꢇ
ꢅ,ꢀꢁꢄ,ꢁꢆꢆ
ꢅ,ꢆꢇꢁ,0ꢈꢇ
ꢅ,ꢈꢀꢃ,ꢈꢃ0
ꢆ,ꢁ0ꢅ,ꢃ0ꢂ
Other patents pending.
© 2009 Uniden America Corp.
Ft. Worth, TX 76155
Printed in Vietnam
UNZZ01052BZ(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
|