®
INSTALL GUIDE
ICEMAKER SERIES
BI2115
WH95
ADA15IM
BI98
SS1095
SS98
SP18
BI95
The Built-In Undercounter Leader Since 1962
ULINE.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Safety Precautions
General Precautions
Use this appliance for its intended purpose only and follow these
general precautions with those listed throughout this guide:
IMPORTANT
• PLEASE READ all instructions before installing,
operating, or servicing the appliance.
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.
• Proper installation procedures must be followed when
completing an installation or relocation of a unit.
Consult the installation guide before any installation
begins. U-Line contact information appears on the rear
cover of this guide.
WARNING
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adaptor.
• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.
• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle, installed
by a qualified electrician, compliant with applicable
electrical codes.
Safety Alert Definitions
• Never use an extension cord to connect power to the
unit.
• Always keep your working area dry.
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
WARNING
DANGER
Install provided Anti-Tip kit on all Wine Captain
Models and Beverage Centers. Serious personal injury
could occur.
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
CAUTION
WARNING
• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.
• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
Warning means that failure to follow this safety
statement could result in serious personal injury,
property or equipment damage.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
IMPORTANT
• Do not lift unit by door handle.
• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.
• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.
• Allow unit temperature to stabilize for 24 hours before
use.
• Do not Block any internal Fans
Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.
U-Line Safety Precautions
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Tools / Material Required
3 Inspect & Plan
•
Screwdrivers — slotted and Phillips head
•
1/4-inch thick door panel material and cutting tools (If installing
a 1/4” Panel)
•
•
•
•
•
•
•
•
•
1/4” Nut Driver
5/16” Nut Driver
Side Cutter
Product Registration
You have received a carton containing your ice maker unit with a
package inside containing a Use and Care Guide, a Product
Registration Card, and a water line kit. Please complete and mail
LineService.com. Once your unit is installed, keep the Use and
Care Guide and this Installation Guide in a safe place for future
reference.
Copper tubing cutter
12” Level
9/16” Open end wrench
7/16” Open end wrench
Pliers
Copper tubing
Models Covered
A complete water hook up kit is also available for purchase from
your dealer. Order U-Line Part No. WATERHOOKUP.
This installation guide covers the following models
Exterior Cleaning
U-ADA15IMB-00
U-ADA15IMS-00
U-ADA15IMS-01
U-BI2115B-00
ULN-BI98B-00
Black and White Models:
ULN-BI95WH-00
ULN-SP18B-03
•
Black and White surfaces may be cleaned with a mild detergent
and warm water solution. Do not use solvent-based or abrasive
cleaners. Use a soft sponge and rinse with clean water. Wipe
with a soft, clean towel to prevent water spotting.
ULN-SP18WH-03
ULN-SS1095FC-03
ULN-SS1095FD-03
ULN-SS1095NF-03
ULN-SS95-03
U-BI2115S-00
Stainless Models:
U-BI2115S-01
•
Stainless door panels, handles and frames can discolor when
exposed to chlorine gas, pool chemicals, salt water or cleaners
with bleach.
U-BI2115SOD-00
U-BI2115SOD-01
U-BI2115W-00
ULN-BI95B-00
ULN-BI95WH-00
•
Keep your Stainless unit looking new by cleaning with a good
quality all-in-one stainless steel cleaner/polish on a monthly
basis. For best results use Claire Stainless Steel Polish and
Cleaner, which can be purchased from U-Line Corporation
(Part numbers 173348). Frequent cleaning will remove surface
contamination that could lead to rust. Some installations may
require cleaning on a weekly basis.
ULN-SS98-03
ULN-WH95TP-03
Please carefully follow the directions that apply to your unit and
your intended design.
•
•
Do not clean with steel wool or abrasive pads.
Do not use cleaners that are not specifically intended
for stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).
•
If any surface discolors or rust appears, clean it quickly with
Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive
cloth. Always clean in the direction of the grain. Always finish
this process with Claire Stainless Steel Polish and Cleaner or
comparable product to prevent further problems.
WARNING
Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
U-Line Inspect & Plan
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BI-98 / SS-98 Models
4 Prepare Site
Filler Panel (Not Provided by U-Line) –
May Be Added Above or Below Unit
to Enclose for a Built-In Look
Your U-Line product has been designed for either free-standing or
built-in installation. When built-in, your unit does not require
additional air space for top, sides or rear. However, the front grille
must NOT be obstructed and clearance is required for an
electrical and water connection in the rear.
IMPORTANT
Typical
Counter
Height
34-1/4"
to
21-1/2"
Minimum
Units can NOT be installed behind a closed cabinet door.
See Electrical
Specifications
for Power Supply
Cut-Out Dimensions
35-1/8"
Cut-Out
Height
27-3/8"
ADA15IM Models
8"
15-3/16"
BI-2115 Models
See Electrical
Specifications
for Power Supply
23-3/4”
Minimum
32"
to
33"
8"
See Electrical
Specifications
for Power Supply
15-1/4"
23-7/8"
Minimum
34-1/8"
to
35-1/8"
BI-95(B)(WH) Models
Filler Panel (Not Provided by U-Line) –
May Be Added Above or Below Unit
to Enclose for a Built-In Look
8"
15-1/4"
SP-18 Models
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
Typical
Counter
Height
34-1/4"
to
3/4"
Minimum Flange
Mounting Area
18-1/2" Minimum
See Electrical
Specifications
for Power Supply
35-1/8"
Cut-Out
26" Minimum
Height
25-1/16"
See Electrical
Specifications
for Power Supply
Cut-Out
Height
18-7/8"
8"
14-3/16"
8" Height
From Floor
Toe Kick
3/4"
14-1/4"
Cut-OutWidth
3/4”
Minimum Flange
Minimum Flange
Mounting Area
Mounting Area
Prepare Site
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SS-1095NF Models
BCM95 Models
Filler Panel (Not Provided by U-Line) –
May Be Added Above or Below Unit
to Enclose for a Built-In Look
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
Typical
Counter
Height
34-1/4"
to
18-1/2”” Minimum
18-1/2" Minimum
See Electrical
Specifications
for Power Supply
See Electrical
Specifications
for Power Supply
Cut-Out
Height
25-1/8”
35-1/8"
Cut-Out
8" Height
Height
From Floor
25-1/16"
8"
14-1/4"
3/4”
14-1/4”
3/4”
Minimum Flange
Mounting Area
Cut OutWidth
Minimum Flange
Mounting Area
SS-1095FC Models
WH95TP Models
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
3/4"
Minimum Flange
Mounting Area
18-1/2" Minimum
18-1/2” Minimum
See Electrical
Specifications
for Power Supply
See Electrical
Specifications
for Power Supply
Cut-Out
Height
25-1/8"
Cut-Out
Height
25-1/8”
8" Height
8" Height
From Floor
From Floor
3/4”
Minimum Flange
Mounting Area
14-1/4”
Cut OutWidth
3/4”
Minimum Flange
Mounting Area
Toe Kick
Minimum Flange
Mounting Area
3/4"
Minimum Flange
Mounting Area
14-1/4"
Cut-OutWidth
3/4”
SS1095FD
BI95BTP
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
Filler Panel (Not Provided by U-Line) –
Needed to Attach Mounting Flange on Unit
3/4"
Minimum Flange
Mounting Area
18-1/2" Minimum
18-1/2” Minimum
See Electrical
Specifications
for Power Supply
See Electrical
Specifications
for Power Supply
Cut-Out
Height
25-1/16"
Cut-Out
Height
8" Height
From Floor
26-1/16"
8" Height
From Floor
Toe Kick
Minimum Flange
Mounting Area
3/4"
14-1/4"
Cut-OutWidth
3/4”
3/4”
Minimum Flange
Mounting Area
3/4”
Minimum Flange
Mounting Area
14-3/4”
Cut OutWidth
Minimum Flange
Mounting Area
Prepare Site
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ADA15IM BI95 95TP BCM95
5 Product Dimensions
ADA15IM Series
BI95(B)(WH)
BI2115
17” *
23”*
23-3/16"
25-1/16"
34-1/8"
32”
8-15/16”
13-15/16"
15”
3-13/16”
*Add 1-1/2” ForWater Line Clearance
15"
*Add 5/8”For Water Line Clearance
*Add 3/4” To Depth For Water Line Clearance
ADA15IM Stainless Series
BI95BTP
BI2115 Stainless
17"*
23-1/8”
23”*
25-1/16"
34-1/8"
8 15/16”
15-1/8"
32”
*Add 1-1/2” For ForWater Line Clearance
BI98 & SS98
3-13/16”
15"
*Add 5/8”For Water Line Clearance
15”
14-15/16"
20” *
*Add 3/4” To Depth For Water Line Clearance
27-3/8"
8-15/16”
*Add 1-1/2” For ForWater Line Clearance
Product Dimensions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SS1095 SP18 BCM95 WH95
SS1095NF
SS1095FD
SP18
15-1/8"
15-15/16”
17” *
26-1/16”
18-7/8"
7 9/16”"
9”
1/2"
24-1/2" *
*Add 1 1/2” ForWater Line Clearance
SS1095FC
*Add 1-1/2”For Water Line Clearance
BCM95
15-1/8”
17” *
15-1/8"
17"*
25-1/8”
25-1/8"
9”
8 15/16”
*Add 1 1/2” ForWater Line Clearance
*Add 1-1/2” For ForWater Line Clearance
SS1095NF
WH95TP
17” *
14”
14"
17"*
25-1/16”
25-1/8"
9”
8 15/16”
*Add 1-1/2” For ForWater Line Clearance
*Add 1 1/2” ForWater Line Clearance
Product Dimensions
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Swing Dimensions
6 Other Site Requirements
Power Supply
All units have a zero clearance for the door to open 90°. U-Line
recommends a minimum door clearance of 2" to accommodate
the handle if the unit is installed next to a wall or similar type of
structure.
Units requires a grounded and polarized 115 VAC, 60 Hz, 15A
circuit (normal household current). See Electrical Specifications on
Page 14.
Wall
ADA15IM Series
Wall
Water Supply
1/4" Min.
2" Min.
Units require a 1/4” OD water supply line and a shut off valve. For
more information see page 15
20-7/8"
20-7/8"
Environmental Requirements
Units are designed to operate between 50°F (10°C) and 100°F
(37°C). High ambient temperatures (100°F [37°C] or higher) may
reduce the unit’s ability to reach low temperatures and may also
reduce the ice production rate for those models with ice makers.
16-1/2"
16-1/2"
If the ambient temperature is expected to drop below 45°F (7°C),
drain all water from the unit to prevent freezing damage, which is
not covered by the warranty.
ꢀꢁꢂ
Door Swing
ꢀꢁꢂ
Door Swing
For best performance, keep the unit out of direct sunlight and away
from heat generating equipment.
(With Handle)
(Without Handle)
For best performance and life outdoors, place under a counter or
provide shelter of some kind.
BI98
Wall
SP18
Wall
In climates where high humidity and dew points are present,
condensation may appear on outside surfaces. This is considered
normal. The condensation will evaporate when the humidity drops.
3/4" Min.
1/4" Min.
.
22"
17-3/8"
16-1/2"
15-1/8"
15-1/2"
90°
Door Swing
90°
Door Swing
SS1095FC/FD
WH95, BI95BTP, BCM95
SS1095NF
Wall
Wall
1/4" Min.
3/4" Min.
14-3/8"
15-1/2"
14-3/8"
15-1/2"
90°
Door Swing
90°
Door Swing
Other Site Requirements
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Remove plastic hole plug from door handle and relocate on
opposite side. See Figure 6
7 Door Reversal
.
Hinge
BI95 & BI98
Reversing the Door
Plastic
Plug Hole
Plastic
Plug Hole
All units may be left- or right-hand opening.
Note: The grille should not yet be installed. If it has been installed,
remove it for door reversing.
Screw
To reverse the door:
Right Side
Door Swing
Left Side
Door Swing
1. Remove top hinge from cabinet (three screws). See Figure 1.
Right Side
Hinge
Invert
Screw
Invert
Hinge
Hold door to keep it from falling.
6
2. Lift the door off the bottom hinge.
7. Remove pivot screw from top hinge, invert screw and reinstall
pivot screw in top hinge. See Figure 7
.
8. Remove three plastic screw
plugs from hinge holes, top of
cabinet, opposite side. Be
careful not to scratch
cabinet. See Figure 8
.
9. Place door on lower hinge
pin. Invert and install upper
hinge on door.
10. Fasten upper hinge to unit
(three screws). Partially
1
2
3. Remove bottom hinge from cabinet (two screws). See Figure 2
Remove screws on opposite side of cabinet (Figure 3). Note
that there may be a nut behind one or both screws on either
side.
.
tighten screws. See Figure
9.
7
11. Adjust door to assure proper
seal. Tighten upper and lower
hinge screws securely.
12. Replace three plastic plugs
removed in Step 8 into holes
on top of unit. Replace
screws in holes in bottom of
unit on opposite side.
8
3
4
4. Install hinge on opposite side,
bottom of cabinet. See
Figure 4. Replace nut on
back side where installed.
Align hinge outer edge with
cabinet before tightening
screws.
5. Relocate plastic spacer/
bushing on bottom of door
to opposite side, and place
door on bottom hinge pin.
See Figure 5. Clean out
5
bushing hole in door bottom
with a screwdriver if necessary.
U-Line Door Reversal
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Relocate plastic spacer/
bushing on bottom of door to
opposite side, and place door
on bottom hinge pin. See
Figure 14. Clean out bushing
hole in door bottom with a
screwdriver if necessary.
WH95TP, BI95BTP, BCM95 & SP18
Reversing The Door
Bushing
All units may be left- or right-hand opening.
To reverse the door:
1. Remove travel pin from cabinet
(two screws). See Figure 9.
Slide assembly through flange
and set aside to be used later.
7. Remove plastic travel pin
from door handle and
relocate on opposite side.
14
See Figure 15
.
2. Remove top hinge from cabinet
(three screws). See Figure 10
.
Hinge
Hold door to keep it from
falling. Slide hinge through
flange.
Travel
Pin Hole
Travel
Pin Hole
3. Lift the door off the bottom
hinge.
9
Screw
4. Remove bottom hinge from
Right Side
Door Swing
Left Side
Door Swing
Right Side
Hinge
Invert
Screw
Invert
Hinge
15
8. Remove pivot screw from top hinge, invert screw and reinstall
pivot screw in top hinge. See Figure 16
.
11
10
cabinet (two screws). See Figure 11. Remove screws on
opposite side of cabinet (Figure 12). Note that there may be a
nut behind one or both screws on either side.
16
17
9. Gently slide upper hinge through flange and fasten upper hinge
to unit (three screws). Partially tighten screws. See Figure 17
.
10. Place door on lower hinge pin.
11. Align door pivot hole with
pivot hole in upper hinge and
insert pivot screw into upper
hinge and tighten securely.
See Figure 18
.
12
13
12. Adjust door to assure proper
seal. Tighten upper and lower
hinge screws securely.
5. Install hinge on opposite side, bottom of cabinet. See Figure 13
.
Replace nut on back side where installed. Align hinge outer edge
with cabinet before tightening screws.
13. Gently slide travel pin
assembly through flange and
then fasten to unit. Make sure
18
travel pin in door engages the closer in the assembly, then
tighten screws on travel pin assembly securely.
U-Line Door Reversal
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Relocate plastic spacer/bushing (Figure 24) on top and bottom
of door to opposite side. Clean out bushing hole in door bottom
with a screwdriver if necessary.
SS1095
Reversing the Door
Depending upon the location of the unit, it may be desirable to
change the side on which the door is mounted.
8. Using a Phillips screwdriver, remove the two screws holding the
custom stainless handle from the original location, and remove
the handle. Remove the two screws on the opposite side of the
door (Figure 25). Do not place handle on door until you have
completed, steps 9 & 10.
To reverse the door mounting, perform the following:
1. Remove grille (one screw) (Figure 19).
Mod el
SS1095FC
Mod el
SS1095FD
Grille
screw
25
19
Hinge
2. Remove top hinge from cabinet (three screws) (Figure 20).
Hold door to keep it from falling.
Plastic
Plug Hole
Plastic
Plug Hole
Hinge screws
Screw
Right Side
Door Swing
Left Side
Door Swing
Right Side
Hinge
Invert
Screw
Invert
Hinge
26
9. Remove plastic hole plug (Figure 26) from door handle and
relocate on opposite side. Lift the handle slightly and press on
the locking tab, then gently pry the hole plug out of the hole
being careful not scratch the top cap.
20
3. Lift the door off the bottom hinge.
4. Remove bottom hinge from cabinet (two screws) (Figure 21).
Press in locking tab, then
lightly pry up to remove hole
plug and move to opposite
side
27
21
22
10. Relocate plastic spacer/bushing on top of door that was
underneath the hinge to the opposite hole in top cap
5. Remove screws on opposite side of cabinet (Figure 22).
11. Attach handle removed in step 7 to opposite side of door
frame. Be sure to tighten all four screws removed in step 7
.
6. Install hinge on opposite side, bottom of cabinet (Figure 23).
Align hinge outer edge with cabinet before tightening screws.
12. Remove pivot screw from top hinge, invert screw and reinstall
pivot screw in top hinge (Figure 27).
1
24
23
U-Line Door Reversal
11
Download from Www.Somanuals.com. All Manuals Search And Download.
28
13. Remove all three screws on the opposite side of the hinge and
carefully lift off the door latch assembly (Figure 28).
14. Place the door latch assembly on opposite side of unit (Figure
29
30
29). Be sure to tighten all three screws securely.
15. Place door on lower hinge pin. Invert and install upper hinge on
door. Fasten upper hinge to unit (three screws (Figure 30).
Partially tighten screws.
16. Adjust door to assure proper seal. Tighten upper and lower
hinge screws securely.
17. Replace screws in holes in bottom of unit on opposite side.
18. Replace the grille.
U-Line Door Reversal
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remove the two outside screws holding
door handle. Slightly separate door
handle from door.
8 Door Panel Installation
Door Panel Preparation
BI-95, BI-2115B(WH), WH95BTP
4. Pull handle up and off.
5. Slide custom door panel insert into 1/4-
inch channel in door front.
A custom door panel may be inserted into the doorframe. Custom
door panels can be flat or raised, as long as the maximum panel
thickness, where inserted into the door reveal (channel), is no
more than 1/4" thick. For raised panels, the depth of the reveal is
1/4" on all four sides.
IMPORTANT
Some units include a magnet on the bottom of the door.
Use care not to damage magnet, when installing door
insert. Do not set door on bottom edge when pushing
insert into place.
IMPORTANT
Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
type of structure.
6. Holding door gasket out of the way, replace handle on door,
making sure it is seated properly on insert and that screw holes
line up.
Panel Dimensions.
7. Install two small screws removed in Step 3
.
The door panel must not weigh more than 20 lbs.
8. Starting at the corners and working inward, push door gasket
into place on door.
Model
BI-95
Width
12 15/16”
14 1/32”
Height
13 15/32”
27 11/16”
13 15/32”
9. Place door on bottom hinge pin and install upper hinge screw.
BI-2115
BI95BTP
12 15/16”
Door Panel Installation (98, SP18, &
ADA15)
Install the insert as follows:
CAUTION
Use care when handling the insert. Insert edges may be
sharp.
1. Remove top hinge screw pin with Phillips head screwdriver.
Remove door by tilting forward and lifting off bottom hinge pin.
2. Pull door gasket out of groove (top edge of door only). Start in
the middle and pull outward, moving toward the edge . This may
BI-95
BI-2115
BI95BTP
take some force.
U-Line Door Panel Installation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Adjust Door
10 Power Supply
Electrical Specifications
Checking Door Alignment
The unit’s door is aligned at the factory before shipment. However,
its alignment could have been disturbed during shipment.
WARNING
SHOCK HAZARD — Electrical Grounding Required.
IMPORTANT
•
•
Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.
Properly aligned, the door’s gasket should be firmly in
contact with the cabinet all the way around the door (no
gaps).
Never use an extension cord to connect power to the
unit.
1. Carefully examine the door’s gasket to assure that it is firmly in
contact with the cabinet.
IMPORTANT
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a
qualified electrician.
2. When inspecting door alignment, make sure the door gasket is
not pinched on the hinge side of the door.
Adjusting Door Alignment
BI-2115
The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A
power supply (normal household current). An individual, properly
grounded branch circuit or circuit breaker is recommended. GFCI
(ground fault circuit interrupter) is usually not required for fixed
location appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be sure to
1. Remove top hinge screw pin Remove door by tilting forward
and lifting off bottom hinge pin.
2. With door upside-down, loosen but do not remove the two
screws on the door’s bottom hinge plate.
consult your local codes.
3. If the top far edge of the door
needs to move UP, move the
hinge plate toward the outside
ADA15IM
SP18
Slotted
of the door and retighten
Mounting
Holes
Notch
(must face toward
center of door)
screws. If the top far edge of
the door needs to move
DOWN, move the hinge plate
toward the inside of the door
and retighten screws.
26-5/16" Minimum
-
23 1/8"
Raise
Lower
Outside
Outside
7"
Door Edge
Door Edge
7"
4. Mount the door to recheck
alignment and repeat Steps 2
and 3 if further adjustment is
necessary.
1-1/2"
1-1/2"
BI95,WH95TP, BI95BTP & BCM95
SS-1095(NF)(FC)(FD)
5. When top edge of door is
parallel to top edge of cabinet,
remove the door and ensure
the two screws are secure.
Door
Closer
Inserts
Preferred
Location
for Receptacle
Acceptable
Location
6. Remove the door closers
from the bottom hinge, clean
Boss
18-1/2"
Minimum
7"
thoroughly and lubricate the mating surfaces with petroleum
jelly.
7"
1-1/2"
1-1/2"
7. Reinstall the closers, lining up the bosses with holes in hinge and
hinge plate.
BI98
BI2115
8. Mount the door, install top hinge pivot pin
All Other Models
1. Loosen (do not remove) top and bottom hinge screws.
2. Align door squarely with cabinet. Make sure gasket is firmly in
contact with cabinet all the way around the door (no gaps).
24"
21-1/2"
Minimum
7"
1"
7"
4"
3. Tighten bottom hinge screws.
4. Tighten top hinge screws.
U-Line Other Requirements
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9
IMPORTANT
11 Plumbing
For units with front mounted water solenoids, route the
water supply line through the unit so it does not come
into contact with any internal components other than the
solenoid valve. Normal operation creates some vibration.
A water supply line contacting an internal component or
cabinet wall can cause excessive noise during operation or
damage to the line.
CAUTION
Plumbing installation must observe all state and local
codes. All water and drain connections MUST BE made by
a licensed/qualified plumbing contractor. Failure to follow
recommendations and instructions may result in damage
and/or harm.
Front Mount
Rear Mount
Water Supply Connection
When connecting the water supply, follow these guidelines:
•
•
•
•
Review the local plumbing codes before you install the unit.
Connect to the cold water supply.
The water pressure should be between 20 and 120 psi.
Water
Connection
The water line MUST have a shut-off valve in the 1/4” O.D.
supply line.
Water Line
•
Leave approximately 8’ of water line to be coiled behind the
appliance. The water line should be looped into 2 coils. This
will allow the unit to be removed for cleaning and servicing.
However, make certain that the tubing is not pinched or
damaged during installation.
4. For recessed installations, allow extra water supply line length to
provide slack for easy removal from the recessed area. This will
also safeguard against kinking the line.
IMPORTANT
U-Line requires the use of copper tubing for installation.
Do not use any plastic water supply line. The line is under
pressure at all times. Plastic may crack or rupture with
age and cause water damage to your home.
1. For units with front mounted water solenoids you must
remove the grille
1. Install the 1/4 inch OD copper water line to the main water
source.
2. Locate the compression fitting and
ferrule packed with the unit. Slide the
compression fitting and ferrule over the
1/4-inch OD water supply line. Do not
use thread sealing compound or tape.
Using two wrenches, tighten the
compression fitting on the supply line.
3. Carefully bend the water supply line into position and connect
the line to the solenoid valve. Avoid kinking the water supply
line.
U-Line Other Requirements
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
12 Install
1. Open the water supply valve in the main water source.
Leveling Information
ADA15IM & BI2115
2. Plug in the powercord.
3. Gently push the unit into position. Be careful not to kink the
water supply line or entangle the electrical cord.
It is recommended that the unit is level.
1. Use a level to check the
levelness of the unit from
front to back and from side
to side. Level should be
placed along top edge and
side edge as shown
4. Re-check the leveling, from front to back and side to side. Make
any necessary adjustments. The unit’s top surface should be
approximately 1/8" below the countertop.
Grille Installation
BI95, BI98, WH95TP, BCM95BTP, BCM95
2. If the unit is not level, adjust
1. Locate and remove the grille screw from the cabinet, using a
standard blade screwdriver (or a 1/4" nut driver).
the feet on the corners of
the unit as necessary (not
available in all models).
1
2. Identify the grille screw hole on the grille itself. It is located
toward the top of the middle recessed section of the grille.
3. Place the two hook-hinges (located on the rear bottom side of
the grille) onto the front lip of the unit base. Swing the grille up
into position, aligning the grille screw hole on the grille to the
grille screw hole on the cabinet. See Below.
4. Insert the screw. Do not overtighten.
Grille Screw
Turn Foot to Adjust
Grille
3. Check the levelness after each adjustment and repeat the
previous steps until the unit is level.
Hook-Hinge
Unit Base
Front Lip
INSTALLATION TIP
If the room floor is higher than the floor in the cut-out opening,
adjust the rear feet to achieve a total unit rear height of 1/8" less
than the opening’s rear height. Shorten the unit height in the front
by adjusting the front feet. This allows the unit to be gently tipped
into the opening. Readjust the front feet to level the unit after it is
correctly positioned in the opening.
SS1095 Models
SS1095NF & SS1095FC models: Place the bottom lip of the grille
on the inside of the base pan and swing grille up into position.
SS1095FD model: Align the tabs on the bottom of the grille with
the slots in the flange and swing grille up into position.
All Other Models
IMPORTANT
Model:
SS109FD
It is extremely important that these units sit on a level
surface, as they do not have feet levelers. If they are not
level, the ice mold will not fill evenly.
Models:
SS1095NF & SS1095FC
Use a level to check the
levelness of the unit from front
to back and from side to side.
Level should be placed along
top edge and side edge as
shown.
Align Tab
With Slots
Insert This Lip Behind Base Plate Lip
1
Align the grille and cabinet screw holes.
Insert the grille screw and tighten. Do not over-tighten
Level & Install Unit
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Troubleshooting
Problem
Q:
Water is leaking under the unit.
Solution
A:
A water leak under the unit is most likely caused by a bad
connection in the water supply line. Make sure the water line’s
brass fitting is screwed tight to its valve and threaded correctly.
Make sure that plumbers tape was NOT used; if it was remove all
traces before reinstalling.
BI-2115 Specific
Problem
Q:
The door remains open unless it is pushed closed.
Solution
A:
The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure the closers are
clean, greased and installed correctly. Also, re-check leveling from
front to back of the unit and readjust if necessary. Make sure that
pivot plate is installed correctly.
Problem
Q:
The custom overlay door was designed to align with the rest of the
cabinet doors, but the unit has crept forward.
Solution
A:
Make sure that the electrical cord and water supply line are not
obstructing the installation.
Level & Install Unit
17
Download from Www.Somanuals.com. All Manuals Search And Download.
®
INSTALLATION GUIDE
SERVICE INFORMATION
If you have a problem with this appliance, your use and care guide has troubleshooting information to help you
quickly identify common problems and provide information on possible cause and remedy. Answers to
Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact
U-Line directly:
GENERAL INQUIRIES:
U-Line Corporation
SERVICE ASSISTANCE:
Phone (800) 779-2547
P.O. Box 245040
FAX (414) 354-5696
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone (414) 354-0300
Email: [email protected]
FAX (414) 354-7905
Email: [email protected]
PARTS ASSISTANCE:
E-mail: [email protected]
ABOUT U-LINE
Building on 45 years, U-Line has captivated those with an appreciation for the finer things with exceptional
design, inspired innovations and attention to even the smallest details.
U-Line is synonymous with premium built-in under counter ice making, refrigeration and wine storage appli-
ances, the U-Line Corporation is committed to luxury under the counter. U-Line is known and respected for
unwavering dedication to product innovation, quality and selection. A bold and broad line of models is the prod-
uct of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was
the first to develop and patent an automatic stand-alone under counter residential ice maker. His foresight and
determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evi-
dent today. The Milwaukee, Wisconsin based family operated business provides continuity and vision from
which innovations continue to be born.
Going forward, U-Line will continue offering best-in-class products that build on the company's numerous pat-
ents and world firsts to guide the under counter industry in realizing its unlimited potential.
U-LINE.COM
The Built-In Undercounter Leader Since 1962
©2010 U-Line Corporation
Publication Number 30287 9/2010 Rev. D
Download from Www.Somanuals.com. All Manuals Search And Download.
|