Use and Care Guide
®
Wine Captain Models:
2115WC and 2115WCOL2
2175WC and 2175WCOL2
2115WC
2175WC
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction ...............................................................................................................................2
Warranty Registration .......................................................................................................2
Please Record Your Model Information ...........................................................................2
1-Safety Precautions ..................................................................................................................4
Safety Alert Definitions .....................................................................................................4
General Precautions ...........................................................................................................4
2-Product Features .....................................................................................................................5
Échelon Wine Captain .......................................................................................................5
3-Optional Commercial Straight Handle ...................................................................................5
4-Service.......................................................................................................................................5
5-Replacement Parts ...................................................................................................................6
6-Operation ................................................................................................................................6
Initial Startup .....................................................................................................................6
Interior Lighting .................................................................................................................6
Electronic Control Panel ....................................................................................................7
7-Normal Operating Sound........................................................................................................7
8-Wine Stocking Recommendations..........................................................................................8
9- Storage, Vacation & Moving..................................................................................................8
10-Product Disposal ....................................................................................................................8
11-Wine Guide ...........................................................................................................................9
Wine Selections Suggestions..............................................................................................9
Suggestions for Matching Food and Wine........................................................................9
Common Food and Wine Matches.....................................................................................9
Guide to Common Styles of Wine....................................................................................10
Common Tasting Terms....................................................................................................10
12-Cleaning and Maintenance ................................................................................................11
General Cleaning .............................................................................................................11
Maintenance ....................................................................................................................11
18-Troubleshooting Guide .......................................................................................................17
19- Electronic Control Quick Guide..........................................................................................18
U-Line Corporation Limited Warranty ....................................................................................19
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Safety Precautions
IMPORTANT
WARNING
PLEASE READ all instructions completely before
attempting to install, operate, or service your unit.
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform maintenance
on the unit until the electricity has been
disconnected.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and/or loss of property
and/or life and will void the warranty.
• Never use an extension cord to connect power to
the unit.
• Proper installation procedures must be followed
if this unit is being initially installed, or is moved
to a new location after being in service. An
INSTALLATION GUIDE for your unit, providing
complete installation information is available
from U-Line Corporation directly, and must be
consulted before any installation is begun. U-Line
contact information appears on the rear cover of
this guide.
• This unit requires connection to a grounded
(three-prong), polarized receptacle that has been
placed by a qualified electrician in accordance
with applicable electrical codes.
• Always keep your working area dry.
WARNING
Safety Alert Definitions
The Anti-Tip Kit must be installed on this unit
before it is used. Serious personal injury could
occur.
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
CAUTION
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp
edges.
• If your model requires defrosting, DO NOT use any
type of heater to defrost. Using a heater to speed
up defrosting can cause personal injury and
damage to the inner lining.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
IMPORTANT
• Do not lift unit by door handle.
CAUTION
• Never install or operate the unit behind closed
doors. Be sure front grille is free of obstruction.
Obstructing free air flow can cause the unit to
malfunction and may void the warranty.
• Failure to clean the condenser every three months
can cause the unit to malfunction. This could void
the warranty.
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
• Allow unit temperature to stabilize for 24 hours
before use.
• If your model requires defrosting, never use an
ice pick or other sharp instrument to help speed
up defrosting. These instruments can puncture
the inner lining or damage cooling unit.
• Use only genuine U-Line replacement parts.
Imitation parts can damage the unit, affect its
operation or performance and may void the
warranty.
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away
your old refrigerator or freezer, take off the doors
and leave shelves in place so that children may not
easily climb inside.
4
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
• A Wine Display Rack, located at the lowest level in the
cabinet is another U-Line exclusive. Bottles are
displayed at an approximate 40° angle.
2 Product Features
Échelon Wine Captain
• Wine Captain Models feature either a stainless steel,
black or full overlay ready door frames.
All Wine Captain Models feature specially designed wine
racks that allow for the proper horizontal storage of
wine. The corks remain moist, which keeps air from
entering the bottles.
a. Stainless steel units feature a wrapped 2 in. (5.1 cm)
wide door frame, handle. Stainless steel doors are
not field reversible.
b. Black units feature a seamless 1-1/2 in. (3.8 cm) wide
door frame with a slightly contoured top mount
integrated door handle that is field reversible and
easy to maintain.
Models 2115WC and 2115WCOL2 will accommodate up to
24 bottles (750 mL size), and Models 2175WC and
2175WCOL2 will accommodate up to 48 bottles (750 mL
size).
c. Door full overlay wood frames are customer
provided, and not supplied by U-Line.
The Right Temperature for Wine
• Self-closing door hinges that engage when the door is
open approximately 8-10 in. (20.3-25.4 cm), ensure a
positive door seal and prevents door bounce back.
Your Wine Captain has been designed to provide three
temperature zones within the cabinet so the specific
storage requirements of your finest wines can be satisfied.
• Stainless steel models feature a full wrap stainless steel
cabinet.
Superior Features of Échelon
• An electronic control panel with digital display allows
you to display the interior temperature in each zone.
The unit is shipped from the factory with a default
temperature of 50°F. The controller only controls the
middle zone. This zone can be set from 45-54°F. The
upper zone will be approximately 5-6°F warmer and
the lower zone will be approximately 5-6°F cooler than
the middle zone. The electronic control and digital
display provide an attractive appearance, and its
method of control provides precise temperatures for
storage of multiple types of wine.
• An optional commercial handle is available through
the dealer to further customize your unit.
• Black models feature a vinyl clad steel cabinet that
provides a rich textured look, and resists scratching,
peeling and flaking.
• Wine Captain Models are not recommended for
outdoor use.
• Wine Captain Models installed in either a free-standing
or built-in configuration must be anchored to prevent
tipping, using the originally provided anti-tip kit.
• An interior light will illuminate automatically as the
door is opened, providing easy visual identification of
the wine. However, you can easily select two other
modes of operation:
Features and specifications are subject to change without
notice.
a. The interior light can be illuminated while the door
is closed, providing an attractive display of your
wine collection for a period of four hours.
Optional Commercial Straight
Handle
3
b. A blackout/Sabbath mode (not Star K certified)
allows you to darken both interior lights and the
LED display, while maintaining complete
temperature control in the unit.
Stainless steel models are shipped from the factory
equipped with the standard curved handle. An optional
commercial straight handle can be purchased directly
from your dealer. Order Part No. 14159-01.
• The door features tinted thermal glass that protects
your wines from potentially harmful light rays while
providing a fashionable appearance.
• Wine racks have a contoured maple front trim that
adds a fashionable appearance to the Wine Captain.
The wood facing may be stained, with a WATER-based
stain, or replaced in its entirety with other woods or
4 Service
Before Calling for Service
®
manufactured products (such as Corian or Sandstone).
If your U-Line product appears to be malfunctioning, read
through the OPERATION section of this guide to ensure
that the function of all controls are clearly understood. If
the malfunction persists, the TROUBLESHOOTING GUIDE
in this guide will assist you in quickly identifying common
problems, and provide information on possible causes and
remedies. Most often, this will resolve the problem
without the need to call for service.
• Five fully extendable sliding wine racks provide easy
access to all wine bottles.
• Black vinyl wine racks blend with the wine bottles,
placing greater emphasis on the wines themselves. The
vinyl holds the wine bottles more effectively than a
chromed or painted finish.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
If Service is Required
1
2
3
4
5
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
ULIN_0184_A
You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
Figure 3
To turn the unit on or off, touch and hold the POWER icon
(Figure 3, 1) on the display panel for approximately five
seconds until the °F symbol flashes and release.
• A small LED above the icon will illuminate to confirm
the touch of any controller icon.
5 Replacement Parts
• The display (Figure 3, 3) will show the unit set-point
temperature when the unit is on and will show OFF
when the unit is off.
When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
• Turning the unit off will override any other control
function.
Interior Lighting
The interior of the cabinet can be illuminated whenever
the door is opened (default mode), illuminated for a four-
hour period, or remained darkened (blackout model).
durability of your product, and may also void its warranty.
The LIGHT icon (Figure 3, 5) on the control panel is used
to change the lighting functions.
6 Operation
To turn the lights and display OFF (blackout mode):
1. Touch and hold the LIGHT icon (Figure 3, 5) for ten
seconds and release (the °F symbol will flash briefly at
the end of the five second period).
2. The interior light and control display (Figure 3, 3) will
go dark.
NOTE: Although the display will not be visible, the
temperature controls in the unit remain active, and the
interior temperature will be maintained.
ULIN_0080_A
Figure 2
3. To exit the blackout mode before the 36-hour period,
repeat Step 1.
IMPORTANT
Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
To illuminate the interior of the cabinet for a four-hour
period:
1. Touch and release the LIGHT icon (Figure 3, 5) to
switch from door-operated lighting control to
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).
Initial Startup
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
2. To return to door-operated lighting control before the
four-hour period is up, repeat Step 1.
IMPORTANT
U-Line recommends the unit be allowed to run
overnight prior to loading with product.
6
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The °F symbol in the display will indicate the individual
zone temperature being displayed as they are scrolling.
Electronic Control Panel
Your Wine Captain has been designed to provide three
temperature zones within the cabinet so the specific
storage requirements of your finest wines can be satisfied.
NOTE: These are product temperatures, not air
temperatures.
• The top horizontal bar in the symbol indicates the
upper cabinet zone.
• The middle horizontal bar in the symbol indicates
the middle cabinet zone.
• The bottom horizontal bar in the symbol indicates
the lower cabinet zone.
1
2
3
4
5
4. After the third scroll cycle is completed, the display will
return to the set-point temperature.
Adjusting Temperature
ULIN_0184_A
IMPORTANT
Figure 4
Adjust the set-point temperature in single
increments, and wait 24 hours for the temperature
to stabilize before rechecking.
The electronic control with digital display (Figure 4) is
configured to show a single temperature continuously.
This set-point temperature is a base number used by the
controller to maintain the temperature zones in your unit.
The factory default set-point temperature is 50°F. This set-
point temperature is used as a gauge if further
1
2
3
4
5
temperature adjustments are required.
A DISPLAY OFF mode is available through the control
panel. This mode allows you to control whether the
display (Figure 4, 3) will be ON or OFF whenever the
door is closed. The icon touch sequence that follows will
switch between both modes:
ULIN_0184_A
Figure 5
To adjust the set-point temperature:
1. Touch and hold the WARMER icon (Figure 4, 2), and
within five seconds press the POWER icon (Figure
4, 1) three times.
1. Press and release either the WARMER icon (Figure
5, 2) or COOLER icon (Figure 5, 4) to put the
controller in the SET TEMPERATURE mode. The °F
symbol (Figure 5, 3) will begin to flash.
2. The display will be either visible or dark when the door
is closed.
NOTE: If no further action is taken, this mode will self
cancel in five seconds, and the original set-point
temperature will be displayed.
3. To return to the previous mode, repeat Step 1.
Temperature Display Selection
2. While the °F symbol is flashing, press the WARMER or
COOLER icon as required to adjust the set-point
temperature.
U-Line products supplied for 110 VAC operation have
temperatures displayed in a default Fahrenheit (°F)
configuration (Figure 4, 3). Models supplied for 220 VAC
operation have temperatures displayed in a default
Celsius (°C) configuration.
3. The change will be set five seconds after adjusting the
temperature and the new set-point temperature will be
displayed.
The display can easily be adjusted for either type of
temperature display. Press and hold the LIGHT icon
(Figure 4, 5) and within five seconds press the COOLER
icon (Figure 4, 4) three times to change the display as
desired.
7 Normal Operating Sound
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. In spite of
this technology, your model may make sounds that are
unfamiliar.
Temperature Display
To display all zone temperatures:
1. Press and hold the WARMER icon (Figure 4, 2) for
approximately five seconds and release when the °F
symbol in the display (Figure 4, 3) begins to flash.
Normal operating sounds may be more noticeable
because of the unit’s environment. Hard surfaces such as
cabinets, wood/vinyl/tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
2. The display (Figure 4, 3) will scroll through three
individual readings at two second intervals per
temperature.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Common refrigeration components, and a brief
description of the normal operating sounds they make,
are listed below. NOTE: Your product may not contain all
of the components listed.
NOTE: If your unit is equipped with a bottom display
rack (Figure 7), stock that rack first.
•
•
•
•
Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
Condenser Fan: Air moving through a condenser may be
heard.
Automatic Defrost/Drain Pan: Water may be heard
dripping or running into the drain pan when the unit is in
the defrost cycle.
ULIN_0019_A
•
Figure 8
NOTE: After stocking, allow unit to run for 24 hours
to stabilize product temperatures.
8 Wine Stocking Recommendations
2. Repeat Step 1 to stock the next higher rack, and
Specially designed wine racks allow for the proper
horizontal storage of wine. The bottles are properly
positioned so the wine remains in contact with the cork to
assure that the cork does not become dry.
continue until all racks are filled (Figure 8)
.
Stock your unit as follows:
9 Storage, Vacation & Moving
If the unit will not be used for an extended period, or
otherwise stored, follow these steps completely:
WARNING
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels.
Failure to do so may result in death or electrical
shock.
1. Remove all consumable contents from the unit.
2. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
ULIN_0205_A
Figure 6
3. Clean and dry the interior of the cabinet (See CLEANING
AND MAINTENANCE: GENERAL CLEANING).
1. The wine racks should be stocked beginning with the
lowest rack, at the back, and working forward.
Stagger the bottles as shown (Figure 6).
4. During periods of non-use, the cabinet must remain
open to prevent the formation of mold and mildew.
Open door a minimum of 2 in. (5 cm) to provide the
necessary ventilation.
10 Product Disposal
If the unit is being removed from service for disposal,
check and obey all Federal, State and/or Local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
ULIN_0204_A
1. Remove all consumable contents from the unit.
Figure 7
2. Disconnect power to the unit and unplug the power
cord from its outlet.
8
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
Suggestions for Matching Food and Wine
DANGER
Although there are no hard fast rules for matching wine
to food, observe some guidelines. Delicate dishes should
be accompanied by lighter more delicate wines. Full-
flavored foods should be matched with fuller-bodied
wines.
RISK OF CHILD ENTRAPEMENT. Before you throw
away your old refrigerator or freezer, take off the
doors and leave shelves in place so that children
may not easily climb inside.
3. Remove the cabinet door.
As a general rule, one should aim to ascend in flavor and
quality of wines served.
Table 1
11 Wine Guide
Serve a:
Before a:
DRY wine
SWEET wine
RED wine
Wine Selections Suggestions
WHITE wine
YOUNG wine
LIGHT-BODIED wine
Selecting the right wine for the right occasion can
sometimes be a seemingly awkward or difficult task for
the beginning wine enthusiast. We would therefore like
to present you with a few suggestions which may provide
a little more confidence and enjoyment when choosing
and serving your wines.
OLD wine
FULL-BODIED wine
Any step back in quality will be noticed. If a fine wine is
tasted prior to a lesser wine, many of the fine wine’s
subtle qualities may be missed.
When selecting wines, keep an open mind and do not be
afraid to be adventurous. Do not view the subject of wine
so seriously it discourages you from learning and
discovering for fear of embarrassment if something is
incorrect. Wine is best viewed as a hobby and enjoyed.
Common Food and Wine Matches
Table 2
Foods
Wines
Fish, Shell Fish, Crab, Oysters
Dry White Wines, Light
Sparkling or Extra Dry
Champagne
When assembling your collection, try not to become
obsessed with “Vintages.” Although a chart can be a
useful tool, generalizations about a specific year have led
more than one collector to disappointment. In many
instances an “Off Year” will provide a better value and
more drinking enjoyment.
Beef, Venison
Full-Bodied Red Wines
Light-Bodied Red Wines
Pork, Veal, Lamb and Poultry
Fruit
Sweet White and Sparkling
Wines
The primary guideline to the subject of wine is your own
palate. Do not be afraid to make mistakes. Experiment,
discover, but most of all, enjoy yourself and your new
U-Line product.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Common Styles of Wine
Red Wines
Full-Bodied Dry
California
French
Italian
Zinfandel, Cabernet
Rhone, Chateauneuf-du-Pape
Barbaresco, Barolo
Medium-Bodied Dry
Light-Bodied Dry
California
French
Pinot Noir
Bordeaux, Burgundy
French
Italian
Beaujolais
Chianti, Bardolino
White Wines
Full-Bodied Dry
California
French
Chardonnay
Montrachet, Meursault
Puligny-Montrachet
Medium-Bodied Dry
California
French
Sauvignon-Blanc
Pouilly-Fuisse, Sancerre,
Vouvray, Graves
Light-Bodied Dry
French
Chablis, Muscadet, Pouilly-Fume
Full-Bodied, Very Sweet
Germany
Frency
Hungary
Beerenauslese
Sauternes
Tokay
Medium-Bodied, Semi-Sweet
Light-Bodied Off Dry
California
Germany
Gewurtztraminer
Liebfraumilch
Germany
Rhine, Mosel, Riesling
Common Tasting Terms
Terminology
Description
Acidity
A critical element of wine that is responsible for preserving the wines freshness. Excess acidity results in an
overly tart and sour wine.
Balance
Body
A desired trait where tannin, fruit and acidity are in total harmony. Wines with good balance tend to age
gracefully.
The weight and presence of wine in the mouth provided by the alcohol and tannin level. Full-bodied wines
tend to have this strong concentration.
Bouquet
Complex
The blending of a wine's aroma within the bottle over a period of time, caused by volatile acidity.
A subjective term often used in tasting. A wine is said to be complex if it offers a variety of flavors and scents
that continue to evolve as it develops.
Flabby
Full-Bodied
Lean
A wine that lacks structure, or is heavy to the taste, lacks acidity.
Wine high in alcohol and extract, generally speaking, fills the mouth, powerful.
Generally describes wines that are slim, lacking of generosity or thin.
Oaky
A desirable flavor imparted to wine if done in moderation. Most wines are aged in oak barrels one to three
years, thereby receiving this toasty oak characteristic. However, if a weak wine is left in contact too long with
an oak barrel it will tend to be overpowered with an oaky taste.
Tannin
Tannins are extracted from the grape skins and stems and are necessary for a well-balanced red wine. Tannins
are easily identified in wine tasting as the drying sensation over the gums. Tannins generally fade as a wine
ages.
10
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
12 Cleaning and Maintenance
General Cleaning
Proper maintenance of your U-Line product will ensure
efficiency, top performance and long life. The
maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if you
have pets or other special considerations.
Exterior Cleaning (As Required)
Black Models:
Defrosting
• Surfaces may be cleaned with a mild detergent and
warm water solution. Do not use solvent-based or
abrasive cleaners. Use a soft sponge and rinse with
clean water. Wipe with a soft, clean towel to prevent
water spotting.
Automatic (Cycle) Defrost Models
Automatic defrost models do not produce frost in normal
operating conditions. However, a frost pattern may be
noticed on the interior walls if the unit is repeatedly
opened in a high heat or high humidity location. If this
frost pattern does not clear within 24 hours, your unit will
require manual defrosting.
Stainless Steel Models:
• Stainless steel surfaces and components can discolor
when exposed to chlorine gas, pool chemicals, salt
water or cleaners with bleach.
WARNING
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
DO NOT use any type of electrical heating device,
ice pick, knife or other sharp instrument to
defrost; this could damage the inner lining or
refrigeration system and void the warranty.
®
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation (P/N 173348).
Comparable products are acceptable. Frequent
cleaning will remove surface contamination that could
lead to rust. Some installations may require cleaning
on a weekly basis.
IMPORTANT
The drain pan was not designed to capture the
water created when manually defrosting. To
prevent water from overflowing the drain pan,
place towels or other absorbent materials over the
interior drain trough, under the evaporator (Figure
9, 1), before defrosting.
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel on stainless steel
surfaces (this includes glass, tile and counter
cleaners).
• If any surface discoloring or rusting appears, clean it
®
®
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Using abrasive pads such as Scotchbrite™ will
cause the graining in the stainless steel to
become blurred.
• Rust that is not cleaned up promptly can penetrate into
the surface of the stainless steel and complete removal
of the rust may not be possible.
Interior Cleaning (As Required)
1
• Disconnect power to the unit. Clean the interior and all
removed components using a mild non-abrasive
detergent and warm water solution applied with a soft
sponge or non-abrasive cloth. Rinse the interior using a
soft sponge and clean water.
ULIN_0187_A
• Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transmit
taste to the interior products and damage or
discolor the interior.
Figure 9
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To defrost:
CAUTION
1. Turn unit off.
DO NOT use any type of cleaner on the condenser
unit.
2. Remove all products from the interior and prop the
door in an open position (2 in. (5 cm) minimum).
4. Clean the condenser coil (Figure 10, 2) using a soft
brush with a “combing” action or vacuum cleaner. Do
not touch the condenser coil.
3. Allow the frost to completely melt naturally. Clean the
interior and all removed components using a mild non-
abrasive detergent and warm water solution applied
with a soft sponge or non-abrasive cloth. NOTE: DO
NOT use any solvent-based or abrasive cleaners. They
will discolor or damage the interior.
5. Position the grille to align the mounting screws with
the holes in the cabinet.
6. Secure, but do not over-tighten both grille screws.
7. Reconnect power to the unit.
Leveling
4. Dampen a soft sponge or non-abrasive cloth in clean
water and wipe down the cabinet interior and removed
components to remove any detergent residue. Rinse the
sponge or cloth in clean water and repeat as necessary
until the cabinet and components are clean.
5. When the interior is dry, turn unit back on.
Condenser Cleaning
Interval - Every Three Months
To maintain operational efficiency, keep the front grille
free of dust and lint and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
WARNING
Disconnect electric power to the unit before
cleaning the condenser.
ULIN_0206_A
To remove and replace the grille for access to the
condenser fins, follow this procedure:
Figure 11
1. Use a level to check the levelness of the unit from front
to back and from side to side. Level should be placed
1
along top edge and side edge as shown (Figure 11)
.
2
ULIN_0203_A
Figure 10
1. Disconnect electrical power to the unit.
2. Loosen two screws (Figure 10, 1) completely.
1
ULIN_0044_A
Figure 12
NOTE: Screws are held in the grille by o-ring retainers,
and will not come free of the grille.
2. If the unit is not level, adjust the feet on the corners of
the unit as necessary (Figure 12)
.
3. Remove the grille.
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level.
WARNING
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
12
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Alignment Check and Adjustment
IMPORTANT
1
When properly aligned:
• The door will not be flush with the top of the
cabinet. The top edge of the door will be 1/8 in.
(3.175 mm) below the cabinet top.
• The door gasket will be firmly in contact with the
perimeter of the cabinet and not pinched on the
hinge side of the door.
2
3
ULIN_0007_A
The following procedure will correct for up to 1/4 in.
misalignment:
Figure 15
1/8"
(3.175 mm)
3. Turn the door upside down and inspect the hinge plate
mounting holes.
• Your plate has slotted mounting holes (Figure
15, 1). Loosen but do not remove the two hinge
plate screws.
4. If door edge opposite the hinges needs to move up,
move plate toward outside of door (Figure 15, 2). If
door edge needs to move down, move plate toward
inside of door (Figure 15, 3). Repeat until top edge of
door is parallel with top of cabinet and tighten screws
ULIN_0834_A
Figure 13
securely (Figure 15, 1)
.
1. Compare the top edge of the door (opposite the
hinges) to the top edge of the cabinet (Figure 13) and
note the type (up or down) of adjustment needed.
ULIN_0835_A
Figure 14
1
ULIN_0004_A
2. Remove the top hinge pivot pin with a Phillips
screwdriver (Figure 14) and lift door off bottom hinge
pin. Be careful not to lose the door closer insert sets.
Figure 16
5. After adjustment is complete, remove the door closers
from the bottom hinge, clean thoroughly and apply
petroleum jelly to the mating surfaces of the closers. Be
sure that bosses on closers (Figure 16, 1) align with
holes in the door and bottom cabinet hinge plates.
Mount door and install top hinge pivot pin.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Reversal (Black Models Only)
1
ULIN_0002_A
Figure 19
2. Remove metal hinge screw plugs (three each, top and
bottom) (Figure 19, 1) from new hinge location. Do
not discard.
3. Remove top hinge (three screws) (Figure 18, 2) and
reinstall hinge screw pin (Figure 18, 1)
.
ULIN_0015_A
Figure 17
All U-Line black units may be left- or right-hand opening.
Stainless steel unit doors cannot be reversed. The doors
are easily reversed by moving the hinge hardware to the
opposite side. The top hinge hardware will be used on the
bottom of the other side and the bottom hinge hardware
will be used on the top of the other side (Figure 17).
1
ULIN_0005_A
To reverse the door:
Figure 20
4. Install the removed top hinge mount on opposite side
BOTTOM (Figure 20)
.
1
2
ULIN_0003_A
Figure 18
1. Remove top hinge screw pin (Figure 18, 1) from door
using a Phillips screwdriver. Remove door by tilting
forward and lifting off bottom hinge pin.
1
ULIN_0004_A
Figure 21
14
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the two door closer inserts (Figure 21, 1) from
3. Replace the bulb only with a genuine U-Line P/N 31317
replacement.
the existing bottom hinge and install as shown on the
new bottom hinge (Figure 20, 1)
.
4. Replace the lens by first inserting the tab side back into
the housing at a slight angle. While gently pushing the
lens towards the tab end, push the free end up into the
housing, and release when you will hear a snap/click.
6. Remove existing bottom hinge (three screws) and
remount on opposite side TOP. Remove hinge screw pin.
7. Remove the plastic hole plug from the top of the door
to allow the pivot pin to be inserted in the new
location. Install the plug into the vacated hole on the
opposite side.
Wine Rack Removal/Installation
To remove a rack from the cabinet:
1. Grasp the end of the rack, and gently slide it out until
it stops.
2. Remove any bottles stored on the rack.
ULIN_0274_A
Figure 22
8. With bottom of door facing up, remove pivot plate
(two screws), flip over, and remount on opposite side of
door (Figure 22) Be sure slanted side of plate
.
faces center.
9. Holding door upright with top of door tilted forward,
place hole of door pivot plate on bottom hinge screw
pin/closer inserts (Figure 20, 1)
.
10. Tilt top of door into position in top hinge and install top
hinge screw pin.
ULIN_0207_A
Figure 24
11. Install metal hinge screw plugs removed in Step 2 in old
hinge holes (three each, top and bottom).
3. Press the left rack release lever (Figure 24) down, and
at the same time, lift the corresponding right rack
release lever up, and pull the rack out until it is free of
the tracks and the cabinet.
Light Bulb Replacement
To replace the light bulb in your U-Line unit:
IMPORTANT
Do not remove the track side rails from the cabinet.
To insert a rack in the cabinet:
2
1
1. Align the left and right rack channels with the tracks
in the cabinet, and ensuring an even track
engagement on both sides, gently push the rack into
the cabinet until it stops.
ULIN_0001_A
Figure 23
2. Before reloading the rack, ensure proper operation of
the travel stops in the left and right track rails by
pulling the rack out gently until it completely stops.
1. Grasp the edges of the light housing lens
(Figure 23, 1) opposite the exposed tab and gently
push the lens toward the tab (Figure 23, 2).
Wood Trim Finishing
2. Pull the edge of the lens down (Figure 23, 1) and
swing it out of the light housing.
®
The U-Line Wine Captain is equipped with wood-
trimmed wine racks that are coated at the factory with a
clear vinyl sealer, which will adequately protect the wood
in normal usage. A final finish coat was not applied so
that the wood trim could be stained to match décor. The
trim on the racks may be coated with a final finish or
stained.
IMPORTANT
ALWAYS use a genuine U-Line replacement bulb (P/N
31317) in the light housing. Use of any other bulb
within the housing will generate excessive heat,
causing damage to the light housing and cabinet
interior, and will compromise the precise
temperature control of your unit.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Remove all dust from the wood, and apply one coat of
WARNING
®
®
Minwax Polycrylic Protective Finish using a synthetic
bristle brush to the wood. This finish should be applied
in a thin coat following the direction of the grain.
Apply the finish to the back and sides of the wood first,
and allow it to dry for two hours. Apply the finish to the
front side of the wood next, and allow it to dry for two
hours. Sand with very fine 220 grit sandpaper. Apply
two addition coats of the finish in the same manner, but
do not sand the trim after the final third coat is applied.
To prevent permanent damage to the inner liner
of your unit, the wood trim MUST be removed
from the unit for staining and/or finishing. Allow
stain/finish to dry thoroughly (at least 24 hours
per coat) in accordance with the product
manufacturer’s instructions prior to
reinstallation. Failure to do so may cause the
inner liner of the unit to have a permanent odor,
which is not covered by the warranty.
7. Allow the final coat to dry for 24 hours before
reinstalling the trim to the cabinet interior components.
If staining the trim is desired, it must be done before the
application of any type of final finish. Review the
following staining/final finish and final finish-only
guidelines when staining/ and or sealing the wood to
ensure proper adhesion and durability of the finish.
Final finish-only application:
1. Remove all screws securing wood trim to interior
components, and remove the trim.
2. Lightly scruff sand the wood trim with 280 or finer grit
sandpaper.
NOTE: Glass in door is tinted. Stain may look darker
when door is closed.
3. Remove sanding dust with a clean, dry cloth.
Staining and final finish application:
4. The factory-applied seal is compatible with virtually all
finishes. A low odor, water clean up, quick-drying finish
1. Remove all screws securing wood trim to interior
components, and remove the trim from the cabinet
interior.
®
®
such as Minwax Polycrylic Protective Finish is
®
®
recommended (Minwax Polycrylic is an ultra fast-
drying water-based finish). Apply a thin coat of a clear,
protective finish, following the container label
directions.
NOTE: Your model will contain an electronic display panel
in the lowest level trim piece. After removing the trim
screws, and gently pulling the trim from its location, a
wiring harness connector will become visible. Unplug the
connector, and remove the trim from the interior.
5. Lightly sand and reapply if desired.
6. Allow the final coat to dry for 24 hours before
IMPORTANT
reinstalling the trim to the cabinet interior components.
DO NOT use oil-based stains on wood trim. Vapors
from oil-based stains will permanently penetrate
the liner and will not dissipate over time.
®
2. Apply Minwax Water-Based Wood Stain to wood with
a synthetic bristle brush or a foam applicator. Allow
stain to penetrate approximately three minutes. Before
the stain is dry, take a stain dampened rag and remove
any excess stain remaining. Wipe in the direction of the
grain with medium pressure to achieve the desired stain
color.
3. After two hours, repeat step 2. This will even out the
color of the wood.
4. Allow stain to dry for a minimum of three hours before
applying the final finish.
5. If desired, sand the wood with very fine sandpaper to
smooth the surface after the staining process.
16
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
ELECTROCUTION HAZARD
13 Troubleshooting Guide
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit does not operate and
electronic display is blank.
No electrical supply
Plug unit in or check circuit breaker.
No interior light
Loose or burned out bulb
Tighten or replace bulb (See MAINTENANCE; LIGHT
BULB REPLACEMENT).
Electronic display is blank and
interior light is OFF with door OPEN. mode.
Unit is in blackout mode lighting
Exit blackout mode
(See OPERATION; INTERIOR LIGHT CONTROL).
Electronic display is blank and
interior light is ON with door OPEN.
A display function has changed.
Touch and hold the warmer temperature button and
touch and release the POWER button three times, then
release the temperature button. The display should
become visible.
Electronic display shows repeating,
randomly flashing symbols and
partial characters.
A factory control mode has been
inadvertently entered.
Touch and hold the warmer temperature button and
touch and release the LIGHT button three times, then
release the temperature button to exit the factory
control mode. The set-point temperature should now
be displayed.
Electronic display shows:
0, 1 to 26, or 99.
A factory control mode has been
inadvertently entered.
Repeatedly touch the warmer temperature button to
advance any number shown to 99 and touch and
release the LIGHT button. The set-point temperature
should now be displayed.
Electronic display shows E3.
Door has been left open longer than Close door completely. The set-point temperature
20 minutes. should now be displayed.
Electronic display shows one or
more of the following:
The unit is displaying an error code. Record the error code(s) displayed and call for service.
E1, E2, E4, E5, E6, E7, E8, E9, E10, P1.
Unit not cold enough. Check
temperatures (See OPERATION for
approximate temperatures).
Control set too warm
Set control to a cooler setting (See OPERATION). Allow
24 hours for temperature to stabilize.
Airflow to front grille blocked
Dirty condenser coils
Airflow must not be obstructed to front grille (See
OPERATION).
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Door gasket not sealing properly
Door adjustment required (See MAINTENANCE; DOOR
ALIGNMENT CHECK AND ADJUSTMENT).
Inaccurate temperature reading
Properly check temperature (See OPERATION).
Unit is too cold. Check temperatures Control set too cold
(See OPERATION for approximate
temperatures)
Set control to a warmer setting (See OPERATION). Allow
24 hours for temperature to stabilize.
The unit frosts up.
High ambient temperatures or
humidity
Defrost unit manually (See MAINTENANCE;
DEFROSTING).
Door gasket not sealing
Adjust door (See MAINTENANCE; DOOR ALIGNMENT
AND ADJUSTMENT and DOOR REVERSAL).
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
17
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Electronic Control Quick Guide
All Models
Task
Touch
Touch
Display
Comment
Turn ON/OFF
Hold 10 seconds
Release when °F flashes.
or
°F flashes after first touch,
set-point saved after 5
seconds of inactivity and °F
stops flashing.*
or
or
Adjust
Temperature
Touch to change temperature
Touch and release
View Actual
Temperature
For Wine Coolers, see Use
and Care Manual.
Hold 5 seconds
Hold
Release when °F flashes.
Change °F-°C
or
Repeat to switch back.
Blackout
Mode
Display (and cabinet light) not Hold light for 10 seconds to
operable in Blackout Mode. exit.
Hold 10 seconds
* Drawer Wine Cooler: Initially, top bar will flash to set to zone. After five seconds of inactivity (or touching light button), the bottom
zone (bottom bar on F flashing) can be adjusted. After five seconds of inactivity, set-point will be stored in unit.
Glass Door Models
Task
Touch
Touch
Display
Comment
Light normally goes on/off
with door opening. Pressing
light button will turn
Cabinet Light
interior light on for 4 hours,
then it will turn off.
Display off when door is
closed (unless cabinet light is
switched on). Repeat to
switch back.
Display Off
Mode
Hold
All Ice Makers
Task
Touch
Touch
Display
Comment
Ice Maker Off
Mode
Hold
Repeat to switch back
Clear Ice & Clear Combo Only
Task
Touch
Touch
Display
Comment
Will automatically return to
ice production when clean
cycle is complete.
Clean Cycle
Hold
Ice Thickness
Adjustment
Hold
Hold
Use warmer/colder to scroll.
Temporary
Shutdown
(Office Mode)
Ice maker will automatically
turn back on in three hours.
NOTE: 38°F is an example; the display will vary with actual set-point. IMPORTANT: Factory recommended set-point is
38°F for refrigerators and beverage centers, and 50°F for wine coolers.
18
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
Download from Www.Somanuals.com. All Manuals Search And Download.
U-Line Corporation Limited Warranty
U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of
one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the
evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from
defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year
warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a
product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the
United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with
the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-
Line shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and
Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall
cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other
charges, including transportation charges for replacements under this warranty and labor costs not specifically covered
by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product.
The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you
The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God,
such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation,
unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the
controls; door reversal; or cleaning the condenser.
If a product defect is discovered during the applicable warranty period, you must promptly notify either the dealer from
whom you purchased the product or U-Line at P.O. Box 245040, Milwaukee, Wisconsin 53224 or at 414-354-0300. In no
event shall such notification be received later than 30 days after the expiration of the applicable warranty period. U-Line
may require that defective parts be returned, at your expense, to U-Lines factory in Milwaukee, Wisconsin, for
inspection. Any action by you for breach of warranty must be commenced within one year after the expiration of the
applicable warranty period.
This limited warranty is in lieu of any other warranty, express or implied, including, but not limited to any
implied warranty of merchantability or fitness for a particular purpose; provided however, that to the
extent required by law, implied warranties are included but do not extend beyond the duration of the
express warranty first set forth above. U-Lines sole liability and your exclusive remedy under this warranty
is set forth in the initial paragraph above. U-Line shall have no liability whatsoever for any incidental,
consequential or special damages arising from the sale, use or installation of the product or from any other
cause whatsoever, whether based on warranty (express or implied) or otherwise based on contract, tort or
any other theory of liability.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
19
Download from Www.Somanuals.com. All Manuals Search And Download.
For General Inquiries:
P.O. Box 245040
Milwaukee, Wisconsin
53224-9540 U.S.A.
Phone (800) 779-2547
FAX (414) 354-5696
For Service and Parts
Assistance:
Email:
E-mail:
For more than four decades, U-Line has distinguished itself as the
leader in built-in under-counter ice making, refrigeration and
wine storage appliances.
An INSTALLATION MANUAL for your unit, providing complete
installation information, is available for download at
including panel size, and instructions are available by visiting
When you need replacement parts, always request genuine U-Line
distributor in your area.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
®
®
undercounter ice makers, Combo ice maker/refrigerators, Wine Captain wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2008 U-Line Corporation
Publication No. 30226
03/2008 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|