Toshiba DVD Player SD 185 User Manual

SD-185/186EKE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
18. Do not use a cracked , deformed, or repaired disc. These discs are easily broken and may cause serious personal  
injury and apparatus malfunction.  
19. If the apparatus should smoke or smell,immediately disconnect the power cord from the wall outlet. Wait until the  
smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire.  
20. While it is thundering, do not touch the connecting cables or the apparatus.  
SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT  
This equipment has been designed and manufactured to meet international safety standards but, like any electrical  
equipment, care must be taken if you are to obtain the best results and safety is to be assured. So, please read the  
points below for your own safety. They are of a general nature, intended to help you with all your electronic consumer  
products and some points may not apply to the goods you have just purchased.  
read the operating instructions before you attempt to use the equipment.  
DO  
DO  
ensure that all electrical connections (including the mains plug, extension leads and inter- connections between  
the pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and  
withdraw the mains plug before making or changing connections.  
consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.  
be careful with glass panels or doors on equipment.  
DO  
DO  
remove any fixed cover as this may expose dangerous voltages.  
DON'T  
DON'T  
obstruct the ventilation openings of the equipment with items such as newspapers, tablecloths, curtains, etc.  
Overheating will cause damage and shorten the life of the equipment.  
allow electrical equipment to be exposed to dripping or splashing, or objects filled with liquids, such as vases,  
to be placed on the equipment.  
DON'T  
place hot objects or naked flame sources such as lighted candles or nightlights on, or close to equipment. High  
temperatures can melt plastic and lead to fires.  
use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety always fit the  
DON'T  
DON'T  
manufacturer's approved stand or legs with the fixings provided according to the instructions.  
listen to headphones at high volume, as such use can permanently damage your hearing.  
leave equipment switched on when it is unattended unless it is specifically stated that it is designed for  
unattended operation or has a stand-by mode. Switch off using the switch on the equipment and make sure that  
DON'T  
DON'T  
your family know how to do this. Special arrangements may need to be made for infirm or handicapped people.  
continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any  
way -switch off, withdraw the mains plug and consult your dealer.  
DON'T  
ABOVE ALL  
-NEVER let anyone especially children push anything into holes, slots or any other  
opening in the case - this could result in a fatal electrical shock;  
-NEVER guess or take chances with electrical equipment of any kind  
-it is better to be safe than sorry!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
CAUTION:  
This Digital Video Disc Player employs a Laser System.  
To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference  
Should the unit require maintenance, contact an authorized service location.  
Use of controls or adjustments or performance of procedures other than those specified herein may result in  
hazardous radiation exposure.  
To prevent direct exposure to laser beam, do not try to open the enclosure.  
Visible and invisible laser radiation when open and interlocks defeated.  
DO NOT STARE INTO BEAM.  
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of  
electric shock do not perform any servicing other than that contained in the operating instructions unless you are  
qualified to do so.  
Be aware that this equipment is still powered when in standby mode. To disconnect this equipment completely from the  
mains power, pull out the power plug from the wall outlet.  
Environmental Information  
All unnecessary packaging has been omitted. The packaging has been made easy to separate into three materials;  
cardboard (box), polystyrene foam (buffer) and polyethylene (bags,protective foam sheet).  
Your DVD player consists of materials which can be recycled and reused if disassembled by a specialised company.  
Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old  
equipment.  
LASER  
Type  
Semiconductor laser  
InGaAIP(DVD)  
AIGaAs(CD)  
Wave length  
658 nm(DVD)  
790 nm(CD)  
Output Power  
10.0 mW(DVD)  
7.0 mW(VCD/CD)  
Beam divergence 60 degrees  
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain  
readily operable.  
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.  
Model No.  
Serial No.  
Retain this information for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
CAUTION!  
WARNING:  
Do not use solvents such as benzene, thinner,  
commercially available cleaners, or anti-static sprays  
intended for analog discs. Since the optical unit  
(laser) of the DVD system operates at a higher  
power than regular DVD or CD players, cleaning  
CDs intended for DVD or CD players may damage  
the optical unit (laser). Therefore, refrain from using  
a cleaning CD.  
RISK OF ELECTRIC SHOCK!  
Never attempt to service this product yourself.  
Opening and removing the covers may expose you  
to dangerous voltage or other hazards. Failure to  
follow this WARNING may result in death or serious  
injury. Refer all servicing not specified in this manual  
to a Toshiba Authorized Service Center.  
Moisture Condensation  
Setup  
Moisture condensation damages the DVD player.  
Please read the following carefully. Moisture  
condensation occurs, for example, when you pour a  
cold drink into a glass on a warm day. Drops of water  
form on the outside of the glass. In the same way,  
moisture may condense on the optical pick-up lens  
inside this unit, one of the most crucial internal parts  
of the DVD player.  
Finding a suitable location  
-Place the set on a flat, hard and stable surface.  
-Do not place the set on a carpet.  
-Do not position the set on top of other equipment  
that might heat it up (e.g., receiver or amplifier).  
-Do not put anything under the set  
(e.g.CDs, magazines).  
-Install this unit near the AC outlet and where the  
AC power plug can be reached easily.  
If you use the DVD player in such a situation, it may  
damage discs and internal parts. Remove the disc,  
connect the power cord of the DVD player to the wall  
outlet, turn on the DVD player, and leave it for two or  
three hours. After two or three hours, the DVD player  
will have warmed up and evaporated any moisture.  
Keep the DVD player connected to the wall outlet  
and moisture  
Space for ventilation  
-Place the apparatus in a location with adequate  
ventilation to prevent internal heat build up. Allow at  
least 10 cm (4.0'') clearance from the rear and the  
top of the set and 5 cm (2.0'') from the left and right  
to prevent overheating.  
condensation will seldom occur.  
5cm (2.0")  
10cm (4.0")  
5cm (2.0")  
10cm (4.0")  
Region Codes  
This DVD player is designed to support the Region  
Management System. Check the regional code  
number on the disc package. If the number does  
not match the player' s region number (see table on  
page 5), the player may be unable to playback the  
disc.  
Avoid high temperatures, moisture, water and  
dust  
-Apparatus shall not be exposed to dripping or  
splashing.  
-Do not place any sources of danger on the  
apparatus (e.g., liquid filled objects, lighted candles).  
Tips:  
-It may not be possible to play CD-R/RW , DVD+R/  
RW , or DVD+R DL in all cases due to the type of  
disc or condition of the recording.  
Cleaning discs  
-If you are having trouble playing a certain disc,  
remove the disc and try a different one. Improperly  
formatted disc will not play on this DVD Player.  
Some problems occur because the disc inside the  
system is dirty (frozen picture, sound disruptions,  
picture distortions). To avoid these problems, discs  
should be cleaned on a regular basis.  
To clean a disc, use a micro fibre cleaning cloth  
and wipe the disc from the center to the edge in a  
straight line. Do not touch the playback side of the  
disc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Discs that can  
be played  
Region  
U.S.A. and  
Canada regions  
ALL  
1
2
3
4
5
6
U.K.,  
Europe regions and  
Japan  
EU Conformity Statement  
ALL  
ALL  
ALL  
ALL  
ALL  
“This product is marked with “CE” and complies therefore  
with the applicable harmonized European standards  
listed under the Low Voltage Directive 2006/95/EC and  
the EMC Directive 2004/108/EC.”  
Asia Pacific,  
Taiwan, Korea  
Responsible for CE-marking is TOSHIBA INFORMATION  
SYSTEMS (U.K.) LTD, Toshiba Court, Weybridge  
Business Park, Addlestone Road, Weybridge,Surrey,  
KT15 2UL, United Kingdom.  
Australia,  
New Zealand,  
Latin America  
Following information is only for EU-  
member States:  
Russia and  
India regions  
The use of the symbol indicates that this  
product may not be treated as household  
waste. By ensuring this product is disposed  
of correctly, you will help prevent potential  
negative consequences for the environment  
and human health, which could otherwise be  
caused by inappropriate waste handling of  
this product. For more detailed information  
about recycling of this product, please  
contact your local city office, your household  
waste disposal service or the shop where you  
purchased the product.  
China, Calcos Islands,  
Walls and Futuna  
Islands  
Unauthorized copying, broadcasting, public  
performance and lending of discs are prohibited.  
Following information is only valid EU-  
member States:  
Disposal of batteries and/or accumulators  
This product incorporates copyright protection tech-  
nology that is protected by method claims of certain  
U.S. patents and other intellectual property rights  
owned by Macrovision Corporation and other rights  
owners. Use of this copyright protection technology  
must be authorized by Macrovision Corporation, and  
is intended for home and other limited viewing uses  
only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is  
prohibited.  
Pb,Hg,Cd  
The crossed out wheeled dust bin symbol  
indicates that batteries and/or accumulators  
must be collected and disposed of separately  
from household waste.  
If the battery or accumulator contains more  
than the specified values of lead (Pb),  
mercury (Hg), and/or cadmium (Cd) defined  
in the Battery Directive (2006/66/EC), then  
the chemical symbols for lead (Pb), mercury  
(Hg) and/or cadmium (Cd) will appear below  
the crossed out wheeled dust bin symbol.  
Notes on copyright  
The unauthorized recording, use, distribution, or revision  
of television programs, videotapes, DVDs and other  
materials, is prohibited under the Copyright Laws of the  
United States and other countries, and may subject you  
to civil and/or criminal liability.  
By participating in separate collection of  
batteries, you will help to assure the proper  
disposal of products and batteries and  
thus help to prevent potential negative  
consequences for the environment and  
human health.  
For more detailed information about the  
collection and recycling programmes available  
in your country, please contact your local city  
office or the shop where you purchased the  
product.  
Helpful hint: Before making or changing any connections, make sure that all the devices are  
disconnected from the power outlet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Table of Contents  
Introduction  
SAFETY PRECAUTIONS  
IMPORTANT SAFETY INSTRUCTIONS  
Setup  
1
1-3  
4
Cleaning discs  
4
Moisture Condensation  
Region Codes  
Table of Contents  
4
4-5  
6
Connections  
Connecting to television  
7-8  
8
9
Connecting to a Stereo System  
Connecting to a Digital AV Receiver  
Connecting the power cord  
9
Product Overview  
Front and Rear panels  
Remote Control  
10  
11  
Getting Started  
Inserting Batteries  
12  
Finding your viewing channel  
Setting up Progressive Scan feature  
Setting the language  
12  
12-13  
13  
. Playback from Disc  
Playable discs  
13-14  
Playback Feature  
Starting disc playback  
14  
Basic playback control  
14-15  
15  
15-16  
16  
Operations for video playback (DVD/VCD/SVCD)  
Selecting various repeat functions  
Viewing the disc playback Information  
Special DVD Features  
16  
Special VCD and SVCD Features  
16  
®
Playing a DivX Disc  
17  
Playing JPEG/Kodak picture CD  
17-18  
DVD menu Options  
Using the Language setup menu  
Using the Video setup menu  
Using the Audio setup menu  
Using the Rating setup menu  
Using the Misc (Miscellaneous) setup menu  
Tray Lock  
18  
18-20  
20  
20-21  
21-22  
22  
Others  
Specifications  
Troubleshooting  
Glossary  
23  
24-25  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
TV, use the audio cables(white/red)to connect  
AUDIO OUT(L/R)jacks of the DVD player to  
corresponding AUDIO IN jacks on the TV(cable  
not supplied).  
Connecting to television  
IMPORTANT!  
Using Component Video Jacks(Y, PB, PR)  
– You only need to make one video connection  
from the following options, depending on the  
capabilities of your television.  
– Connect the DVD player directly to the  
television.  
Using SCART socket  
MAINS  
IMPORTANT!  
-The progressive scan video quality is only  
possible when using Y, PB, PR and a progressive  
scan TV is required.  
A
B
C
Use the component video cables (red/blue/green) to  
connect the DVD player' s Y, PB, PR jacks to the  
corresponding Component video input jacks (or  
labelled as Y, Pb, Pr) on the TV (cable not supplied).  
Use the audio cables (white/red) to connect AUDIO  
OUT (L/R) jacks of the DVD player to the  
corresponding AUDIO IN jacks on the TV(cable not  
supplied).  
Use the scart cable to connect the DVD SCART OUT  
to the corresponding scart input socket on the TV  
(cable not supplied).  
If your DVD player will not be connected to a Stereo  
System or AV Receiver to hear better sound, scart is  
enough for both audio and video connections.  
A
Proceed to page 12 for detailed Progressive Scan set  
up.  
Using Composite Video Jack(CVBS)  
Using a RF modulator  
A
Use the composite video cable (yellow) to connect  
the DVD player' s VIDEO(CVBS) jack to the video  
input jack(or labelled as A/V in,Video In or  
Composite) on the TV(cable not supplied).  
To hear the sound of this DVD player through your  
Helpful hint: Before making or changing any connections, make sure that all the devices are  
disconnected from the power outlet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
IMPORTANT!  
-If your TV only has a single Antenna In jack (or  
labelled as 75 ohm or RF In), you will need an RF  
modulator in order to view the DVD playback on  
the TV.  
Connecting to a Stereo System  
A
Use the composite video cable (yellow) to connect  
the DVD player' s VIDEO (CVBS) jack to the video  
input jack on the RF modulator (cable not supplied).  
To hear the sound of this DVD player through your  
TV, use the audio cables(white/red) to connect  
AUDIO OUT (L/R) jacks of the DVD player to the  
corresponding AUDIO IN jacks on the RF modulator  
(cable not supplied).  
B
C
Use the RF coaxial cable (not supplied) to connect  
ANTENNA OUT or TO TV jack on the RF modulator  
to the ANTENNA IN jack on the television.  
Connect the Antenna or Cable TV service signal to  
the ANTENNA IN or RF IN jack on the RF modulator.  
(It may have been connected to your TV previously.  
Disconnect it from the TV.)  
MAINS  
Stereo system has Dolby Pro Logic or Right/Left  
Audio In Jacks  
A
B
Select one of the video connections (CVBS VIDEO  
IN, SCART IN or COMPONENT VIDEO IN)  
depending on the options available on your TV.  
Use the audio cables (white/red) to connect AUDIO  
OUT (L/R) jacks of the DVD Player to the  
corresponding AUDIO IN jacks on the stereo system  
(cable not supplied).  
Helpful hint: Before making or changing any connections, make sure that all the devices are  
disconnected from the power outlet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
Connecting to a Digital AV Receiver  
Connecting the power cord  
MAINS  
After everything is connected properly, plug in the AC  
power cord to the power outlet.  
Never make or change any connections with the  
power switched on.  
Receiver has a PCM, Dolby Digital or MPEG  
decoder  
A
B
C
Select one of the video connections (CVBS VIDEO  
IN, SCART IN or COMPONENT VIDEO IN)  
depending on the options available on your TV.  
Connect the COAXIAL jack of the DVD player to the  
corresponding Digital Audio In jack on your Receiver  
(cable not supplied).  
Set the DVD Player' s Digital Output to PCM or All  
depending on the capabilities of your Receiver (see  
page 20 {Digital Output}).  
Tip:  
-If the audio format of the Digital Output does not  
match the capabilities of your receiver, the receiver  
will produce a strong, distorted sound or no sound at  
all.  
Helpful hint: Before making or changing any connections, make sure that all the devices are  
disconnected from the power outlet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
Front and Rear panels  
I/2ON/STANDBY  
-Turns the player on or switches it to  
standby mode  
Disc tray  
- Place a disc here  
B/X PLAY/ PAUSE  
-Starts or pauses playback  
Display  
- Shows information about the current status of the  
DVD Player  
STOP  
- Stops playback  
IR Sensor  
- Points the remote control towards this sensor  
çOPEN/CLOSE  
- Opens or closes the disc tray  
MAINS ~  
- Connects to a standard AC outlet  
SCART OUT  
- Connects to SCART input of a TV  
AUDIO OUT (Left/Right)  
- Connects to Audio input of a TV, an amplifier,  
receiver or stereo system  
Y, PB, PR Component Video Out  
- Connects to Y, PB, PR input of a TV  
COAXIAL(Digital audio out)  
- Connects to coaxial Audio input of a digital audio  
equipment  
VIDEO Out (CVBS)  
- Connects to CVBS Video input of a TV  
DVD display  
The indicators vary depending on the kinds of disc  
you play.  
DVD video disc  
VIDEO CD  
Audio CD  
Chapter/Track  
number indicator  
•During playback:  
Example  
•During playback:  
Example  
•During playback:  
Example  
Some discs may only Some discs may only Some discs may only  
display chapter  
numbers.  
display track  
numbers.  
display track  
numbers.  
Multifunctional indicator (indicates  
operating status or messages, etc.)  
OPEN  
LOAD/CLOSE  
No disc  
Bad disc  
"----" may also appear in other situation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀ0  
Product Overview  
Remote Control  
See the page in [ ] for details.  
[ 16 ]  
REMOTE SIGNAL EMITTER  
DISPLAY  
[ 12 ]  
-Displays information on  
-Point remote control to the sensor on  
TV screen during playback  
the front panel  
2
[ 12, 14 ]  
ON / STANDBY  
[ 14 ]  
OPEN/CLOSE  
-To switch the DVD player to ON or  
-Open/close the disc tray  
standby mode  
[ 14, 16, 21 ]  
-Selects numbered items in a menu  
Number Buttons  
[ 16 ]  
T - SEARCH  
-Start playback from a designated  
-Press to enter track/chapter/title  
numbers or password directly  
point  
[ 13, 18 ]  
SETUP  
-Enters or exits the system setup  
[ 14 ]  
+10 button  
menu  
-Press to enter number greater than 9  
-Press +10 button repeatedly to select  
10,20,30...etc  
   [ 15, 17, 18 ]  
-Cursor buttons for moving to the left  
/ right / up / down  
-To rotate the JPEG picture during  
playback  
[ 15, 16 ]  
MENU  
-Enters or exits the disc menu  
-Switches on or off the Playback  
Control (PBC) mode (for VCD 2.0 /  
SVCD only)  
STEP  
-Play video frame by frame  
[ 14, 15 ]  
-Starts or pauses playback  
[ 15 ]  
PLAY/PAUSE  
[ 13 ]  
OK  
-Acknowledge menu selection  
STOP  
-Stops play  
[ 16 ]  
RETURN  
-To go back to previous menu  
[ 16 ]  
SUBTITLE  
-To access subtitle language  
[ 16 ]  
-Show title menu  
TITLE  
[ 16 ]  
ANGLE  
-Switch the camera angle during  
playback  
[ 16 ]  
AUDIO  
[ 15 ]  
F.R & F.F  
-Selects an audio setting (DVD) or an  
audio channel (VCD)  
-Do a forward/reverse search  
[ 14, 16 ]  
PREV & NEXT  
-Skip to previous / next chapter /track  
[ 15, 18 ]  
ZOOM  
-Enlarge a picture on the TV  
[ 15 ]  
REPEAT  
-Selects various repeat mode  
[ 17 ]  
RANDOM  
-Toggles between Normal and Shuffle  
[ 16 ]  
A-B  
playback  
-Repeats playback from point A to B on  
a disc  
[ 15 ]  
PROG  
-To program playback or cancel the  
program playback  
[ 15 ]  
SLOW  
-Do a slow forward  
[ 15 ]  
CLEAR  
-Delete the mistyped entries or cancel  
some functions  
ꢀꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting Started  
and highest channels and may be called FRONT,  
A/V IN or VIDEO. See your TV' s manual for more  
details.  
Inserting Batteries  
Or, you may go to channel 1 on your TV, then  
press the Channel down button repeatedly until you  
see the Video In channel.  
Or, the TV remote control may have a button that  
chooses different video modes.  
Or, tune the TV until you can see the DVD player  
signal from the RF modulator (refer to your TV user  
manual).  
C
If you are using external equipment, (such as  
audio system or receiver), turn it on and select the  
appropriate input source for the DVD player output.  
Refer to the equipment user’s manual for detail.  
A
B
Open the battery compartment.  
Insert two batteries type R03 or AAA, following the  
indications (+ / - ) inside the compartment.  
Close the cover.  
C
Setting up Progressive Scan feature  
CAUTION:  
Never throw batteries into a fire.  
Note:  
(For Progressive Scan TV only)  
- Be sure to use AAA size batteries.  
- Dispose of batteries in a designated disposal area.  
- Batteries should always be disposed of with the  
environment in mind. Always dispose of batteries in  
accordance with applicable laws and regulations.  
- If the remote control does not operate correctly, or if  
the operating range becomes reduced, replace batteries  
with new ones.  
- When necessary to replace batteries in the remote  
control, always replace both batteries with new ones.  
Never mix battery types or use new and used batteries  
in combination.  
- Always remove batteries from remote control if they  
are dead or if the remote control is not to be used for an  
extended period of time. This will prevent battery acid  
The progressive scan display twice the number  
of frames per seconds than interlaced scanning  
(ordinary normal TV system). With nearly double  
the number of lines, progressive scan offers higher  
picture resolution and quality.  
Before you start...  
-Ensure that you have connected this DVD player  
to a progressive scan TV using the Y, PB, PR  
connection (see page 7).  
-Ensure that you have completed the basic  
installation and set up.  
Turn on your TV and select the video input  
connected to the DVD player (refer to your TV user  
manual).  
Press 2ON/STANDBY on the remote control to turn  
on the DVD player.  
A
B
from leaking into the battery compartment.  
Using the Remote Control to Operate  
the System  
The blue DVD background screen will appear on  
the TV.  
C
D
Press SETUP.  
Press /to select { Video }, then press .  
Aspect Ratio  
: 4:3  
Language  
Video  
View Mode  
TV System  
Video Out  
:Auto Fit  
:PAL  
30  
30  
Within about 6m (19 feet)  
Component  
RGB  
Smart Picture  
Audio  
OPEN/CLOSE DISPLAY  
ON/STANDBY  
P-Scan  
1
2
3
Rating  
Misc  
A
B
Aim the Remote Control directly at the remote sensor  
(IR) on the front panel.  
Do not put any objects between the Remote Control  
and DVD Player while operating the DVD Player.  
E
F
Press /to select { Video Out }, then press .  
Select { P- Scan }, then press OK to confirm.  
The menu will appear on the TV.  
Video Out  
Finding your viewing channel  
Activating Progressive Scan 1. Ensure  
your TV supports Progressive Mode  
2. If there is a distorted picture on the  
TV, wait 15 seconds for automatic  
recover  
A
B
Press I/2ON/STANDBY on the DVD player to turn it  
on.  
Turn on the TV and set it to the correct video-in  
channel. You should see the blue DVD background  
screen.  
Yes  
No  
Usually these channels are between the lowest  
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀꢁ  
Getting Started/Playback from disc  
soundtrack from audio, subtitles and DVD menu  
languages. If the language selected is not available  
on the disc, the disc’s default language will be used  
instead.  
G
Press to highlight { Yes } and press OK to confirm.  
The reconfirmation menu will appear on the TV.  
Video Out  
Confirm again to use new setting  
14  
OSD language : English  
Language  
Subtitle  
: Off  
Yes  
No  
DivX Subtitle  
Audio  
: Standard  
English  
Video  
Audio  
H
A
Press to highlight { Yes } and press OK to confirm.  
The setup is now completed and you can start  
enjoying the high quality picture.  
DVD Menu  
German  
Polish  
Rating  
Misc  
Hungarian  
Portuguese  
To deactivate Progressive Scan  
manually:  
Wait for 15 seconds for the auto recovery.  
A
B
C
Press SETUP.  
OR  
Press /to select { Language }, then press .  
Press /to highlight one of the options below,  
then press .  
{ Subtitle }  
Select this to change the subtitle language.  
{ Audio }  
A
B
Press OPEN/CLOSE çon the DVD player to open  
the disc tray.  
Press number button ' 1 ' on the remote control for a  
few seconds.  
The DVD background screen appears.  
Select this to change the disc soundtrack language.  
{ DVD Menu }  
Tip:  
Select this to change the language of the disc menu.  
Use /to select a language and press OK to  
confirm.  
-There are some progressive scan TVs and High-  
Definition TVs that are not fully compatible with this  
unit, resulting in the unnatural picture when playing  
back a DVD VIDEO disc in the progressive scan  
mode. In such a case, turn off the progressive scan  
feature on both the DVD player and your TV.  
D
E
Repeat steps C - D for other language settings.  
IMPORTANT!  
-DVD discs and players are designed with regional  
restrictions. Before playing a disc, make sure the  
disc is for the same zone as your player.  
Setting the language  
-If '  
'appears on the TV screen when a button is  
pressed, it means the function is not available on  
the current disc or at the current time.  
Choose your desired On-Screen Display(OSD)language  
where available.  
On-Screen Display (OSD) Language  
Playable discs  
The On-screen language for the system setup menu  
will remain as you set it, regardless of various disc  
languages.  
Using this DVD player, you can playback on the  
following discs. Some of these discs may be  
incompatible.  
OSD language  
Subtitle  
English  
Deutsch  
Language  
Video  
DVD Video disc(Digital Versatile Disc)  
DivX Subtitle  
Audio  
Polski  
Hungarian  
Audio  
Rating  
Misc  
DVD Menu  
Português  
DVD+R/RW (DVD Recordable / Re-  
writable), DVD+R DL (Dual layer)  
Audio/Video formats or  
JPEG files.  
A
B
C
Press SETUP.  
Press /to select { Language }  
Press to highlight { OSD language }, then press  
.  
CD-R (CD-Recordable)  
Audio/Video format or  
JPEG files.  
D
Press /to select a language and press OK.  
Audio, Subtitle and DVD menu  
language  
You can choose your own preferred language or  
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
ꢀꢂ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback from disc/Playback Feature  
CD-RW (CD-Rewritable)  
Audio/Video format or  
JPEG files.  
– For DVD+R and DVD+RW multi border , both  
finalized and unfinalized disc cannot be supported.  
Audio CD (Compact Disc  
Digital Audio)  
Starting disc playback  
Video CD  
(Formats 1.0, 1.1, 2.0)  
A
Turn on the TV and select the video input connected  
to the DVD player.  
B
C
D
Press 2ON / STANDBY to turn on the DVD player.  
Press OPEN/CLOSE to open the disc tray.  
Place a disc onto the disc tray with the label facing  
up, then press OPEN/CLOSE.  
Super Video CD  
For double-sided discs, load the side which you  
want to play facing up.  
E
Playback may start automatically. If not, press PLAY/  
is a trademark of DVD Format/Logo Licensing  
Corporation.  
PAUSE  
.
If a disc menu appears on the TV, see page 15  
'Using the disc menu'.  
If the parental control was activated for the  
inserted disc, you have to enter your four-digit  
Because of problems and errors that can occur  
during the creation of DVD and CD software and/or  
the manufacture of DVD and CD discs, Toshiba  
cannot assure that this DVD player will successfully  
play every disc bearing the DVD and CD logos. If you  
happen to experience any difficulty playing a DVD  
and/or CD disc on this DVD player, please contact  
Toshiba Customer Service.  
password, see page 21.  
For more playback features, see pages 14 - 18.  
Tips:  
-Do not overturn the DVD player while disc loading,  
playing or ejecting.  
-Do not close the disc tray manually even if the  
power is switched off.  
This DVD player requires discs/recordings to meet  
certain technical standards in order to achieve  
optimal playback quality. There are many different  
types of recordable disc formats (including CD-R  
files). Not all recordable discs will operate or produce  
optimal playback quality. The technical criteria set  
forth in this owner's manual are meant only as a  
guide.  
You must obtain any required permission from  
copyright owners to download or use copyrighted  
content. Toshiba cannot and does not grant such  
permission.  
Basic playback control  
Unless otherwise stated, all operations described are  
based on Remote Control use.  
Pausing playback  
A
B
During playback, press PLAY/PAUSE  
playback and display a still picture.  
to pause  
Supported Formats  
Sound will be muted.  
To resume normal playback, press PLAY/PAUSE  
again.  
JPEG/Pictures  
-The file extensions has to be '.JPG ' and not  
'.JPEG' .  
-JPEG/ISO format.  
-Maximum of 5760×3840 resolution can be  
supported.  
-Maximum file size: 10M.  
Skipping chapter/track  
Press PREV  
/ NEXT  
to go to the previous  
or next chapter/track during playback.  
When PREV  
is pressed after the first 5  
-It can only display DCF-standard still pictures or  
JPEG pictures such as TIFF.  
DivX®  
seconds of playback, playback will start from the  
beginning of the current chapter/track. If you press  
the button within the first 5 seconds, playback will  
start from the beginning of the preceding chapter/  
track.  
-The file extensions has to be '.AVI ', '.MPG ' or  
'.MPEG '.  
-DivX® 3.11, 4.x, 5.x and 6.0.  
-Q-pel accurate motion compensation.  
Global Motion Compensation (GMC) playback.  
-Official DivX® Certified product.  
-Plays all versions of DivX® video (including DivX® 6)  
with standard playback of DivX® media files.  
Press DISPLAY to display the disc  
information for title/chapter/track.  
Use Number buttons to enter valid chapter / track  
number directly. For the track/chapter numbers which  
are greater than 9, use +10button. Each  
presses increases the number by 10. Then press the  
second digit of track/Chapter number.  
Tips:  
– Maximum 100 sessions for CD and 10 multi border  
for DVD are supported.  
– For DVD-R, DVD-RW multi border, only finalized  
disc can be supported.  
The playback skips to the selected chapter / track.  
Helpful hint: Some discs cannot be played on this DVD player due to the configuration and characteristics  
of the disc, or due to the condition of recording and authorizing software  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀꢃ  
Playback Feature  
control, then press OK to start playback.  
To access or remove the menu.  
Press MENU on the remote control.  
la  
ybac  
Stopping playback  
During playback, press STOP  
.
A
The DVD player memorises the stopped point.  
Press PLAY/ PAUSE  
location where you stopped playback.  
If you press STOP  
again, the DVD player will  
Zooming In  
to resume playback from the  
This function allows you to enlarge the picture on the  
TV screen and to pan through the enlarged picture.  
cancel the resume function.  
A
B
During playback, press ZOOM repeatedly to display  
the picture with different scales.  
Tips:  
-Screen saver will start automatically if the disc  
playback is stopped for about 2 minutes.  
-The player will automatically switch to Power  
Standby mode if you do not press any buttons for  
about 22 minutes after the disc has stopped playing.  
Use ///to pan through the enlarged picture.  
Playback will continue.  
Press ZOOM repeatedly to return to the original size.  
Slow Motion  
Program playback  
A
B
Press SLOW during playback to select the required  
speed: 1/2, 1/4, 1/8( forward only ).  
During playback, press PROG, then the OSD will  
appear as below:  
Sound will be muted.  
To return to normal speed, press PLAY/ PAUSE  
.
For VCD:  
Program  
Forward/ Reverse Searching  
1
2
Track  
Track  
Track  
Track  
1
2
3
4
3
4
You can fast forward or fast reverse a disc during  
playback and select a desired search speed.  
For DVD,VCD, SVCD,CD  
5
6
7
8
9
10  
12  
14  
16  
11  
13  
15  
Track  
Track  
5
6
A
B
During playback, press F.R/ F.F to select the required  
speed: X2, X4, X8, X16(backward or forward).  
Sound will be muted (DVD/VCD/SVCD) or  
intermittent (CD).  
Clear  
Play  
Clear All  
To return to normal speed, press PLAY / PAUSE  
.
For DVD:  
Program  
1
2
Selecting various repeat functions  
Repeat play mode  
Title  
Title  
Title  
Title  
1
2
3
4
3
4
5
6
7
8
9
10  
12  
14  
16  
11  
13  
15  
The repeat play options vary depending on the disc  
type.  
Clear  
Play  
Clear All  
A
While playing a disc, press REPEAT repeatedly to  
choose a repeat options.  
A
B
Use the /and OK button to select your desired  
title/chapter/track in the list.  
When you have finished programming, press to  
move the cursor to the 'Play', then press the OK  
For DVD  
-Repeat Chapter (currently playing chapter)  
-Repeat Title (currently playing title)  
-Off (cancel)  
button or directly press PLAY/PAUSE  
start the program playback.  
button to  
For Video CD, Audio CD  
-Repeat Single (currently playing track)  
-Repeat All (entire disc)  
-Off (cancel)  
C
D
Press CLEAR or select ' Clear ' to delete one by one  
from last chosen track / title /chapter or select 'Clear  
All' to clear all the programmed tracks/titles.  
Press STOP twice to cancel program playback.  
For JPEG  
-Repeat Single (currently playing file)  
-Repeat All (current folder)  
-Off (cancel)  
Operations for video playback (DVD/  
VCD/SVCD)  
Tip:  
Using the disc menu  
-For VCD2.0/SVCD discs, repeat playback is not  
possible if the PBC mode is turned on.  
Depending on the disc, a menu may appear on the  
TV screen once you load in the disc.  
To select a playback feature or item  
Use ///or number buttons on the remote  
Helpful hintThe operating features described here might not be possible for certain discs.  
Always refer to the instructions supplied with the discs.  
ꢀꢈ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback Feature  
Repeating a section within a chapter/  
track  
You can repeat the playback of a specific segment  
within a chapter or track. To do this, you must mark  
the start and end of the segment you want.  
Angle  
When {Angle} information appears on the screen,  
press ANGLE button on the remote control  
repeatedly to switch between different angles.  
Playback will go to the selected angle.  
A
B
While playing a disc, press A - B at your chosen  
starting point.  
Press A - B again at your chosen end point.  
Special DVD Features  
The section will now repeat continuously.  
Playing a Title  
C
To exit the sequence, press A - B.  
Press TITLE.  
A
Viewing the disc playback Information  
The disc title menu appears on the TV screen.  
Use ///or number buttons (0-9) to select a  
play option.  
B
C
You can view the disc information (such as current  
title/chapter/track number, total playing time or  
remaining time on the disc) without interrupting the  
disc playback.  
Press OK to confirm.  
Changing the Audio Language  
For DVD:  
A
During playback, press DISPLAY repeatedly on the  
remote control.  
Press AUDIO repeatedly to select different audio  
languages.  
The available disc information appears on the TV  
Changing the Audio Channel  
For VCD:  
Press AUDIO to select the available audio channels  
screen with the following sequence.  
Time  
(DVD)  
(DVD)  
Time  
000333/012446  
provided by the disc (Left, Right, Mix, Stereo).  
Title  
Subtitles  
Title 1/1  
Chapter  
Chapter 2/8  
Audio  
Press SUBTITLE repeatedly to select different  
subtitle languages.  
Audio 1/1  
D6Ch Eng  
(DVD)  
(DVD)  
(DVD)  
(VCD)  
Subtitle  
Subtitle  
Special VCD and SVCD Features  
1/8 Eng  
Angle  
Angle 1/4  
For VCD with Playback Control ( PBC ) feature  
(version 2.0 only)  
Time  
Time  
000333/000500  
Press MENU to toggle between ' PBC On ' and '  
Track  
Track  
OR  
Time  
Time  
PBC Off '.  
3/24  
(VCD PBC OFF)  
If you select ' PBC On ', the disc menu ( if  
available ) will appear on the TV.  
Use the number buttons ( 0-9 ) to select a play  
option.  
(VCD PBC ON)  
(VCD PBC ON)  
000333/000500  
PBC On  
Press PREV  
or next track.  
When PREV  
/ NEXT  
to go to the previous  
Title/Chapter/Track/Time selection  
is pressed after the first 5  
seconds of playback, playback will start from the  
beginning of the current track. If you press the button  
within the first 5 seconds, playback will start from the  
beginning of the preceding track.  
A
Press T-SEARCH, then press /to select  
{ Time }, { Title }, { Chapter } or { Track }.  
For VCD:  
PBC OFF  
During playback, pressing RETURN will return to  
the menu screen (if PBC is on).  
If you want to skip the index menu and playback  
directly from the beginning.  
Track  
---  
Time  
--:--:--  
--:--:--  
(desired time of the current track)  
(desired time of the disc)  
Disc Time  
For DVD:  
Title  
Press MENU on the remote control to turn the PBC  
off.  
---  
---  
Chapter  
Time  
--:--:--  
(desired time of the disc)  
B
C
Use the number buttons ( 0-9 ) to input a valid  
number or time("0"cannot be input as the first  
number). (This function only apply to DVD/VCD.)  
Press OK to confirm.  
The playback skips to the selected title/chapter/  
track/time.  
Helpful hintThe operating features described here might not be possible for certain discs.  
Always refer to the instructions supplied with the discs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀꢄ  
Playback Feature  
Press PREV  
/ NEXT  
to select the  
previous/next file in the current folder.  
®
Playing a DivX Disc  
Press PLAY/PAUSE  
repeatedly to  
pause/resume playback.  
This DVD player supports the DivX® movie playback  
that you download from your computer onto a CD-  
R/RW or DVD+R/RW (see pages 13-14 for more  
information).  
®
Play modes for DivX /Audio CD/JPEG  
You are able to modify the play modes through the  
toolkit which appears on the right of below picture  
on the screen. Press / to navigate between the  
windows and / buttons to select files/ tracks or  
play mode items. Then press OK . Please refer to  
below steps to playback files /tracks in the Program  
View list:  
A
B
Load a DivX® disc.  
The data disc menu appears on the TV screen.  
Press /to select the folder and press OK to  
open the folder.  
Press /to select a file.  
Press OK to confirm.  
C
D
Press SUBTITLE on the remote control will turn  
on or off the subtitle.  
A
B
C
Select Edit Mode in the toolkit then press OK to  
start edit mode.  
Select a file/track or more files/tracks you want in the  
original view list.  
Select Add To Program in the toolkit then press  
OK. ' ' will disappear from screen. It means that the  
files/tracks you have selected already added into the  
Program View list.  
Select Program View in the toolkit then press OK to  
open the file/track in the Program View list that you  
already selected in step B.  
If multilingual subtitles are embedded on the DivX®  
disc, pressing SUBTITLE will change the subtitle  
language during playback.  
Tips:  
–Subtitle files with the following filename extensions  
(.srt, .smi, .sub, .ssa, .txt) are supported but do not  
appear on the file navigation menu.  
–The subtitle filename(.sub) has to be saved under  
the same filename as the movie(.avi) in the same  
folder.  
D
E
Press PLAY / PAUSE  
to playback all files/tracks  
[For example, Folder A: abc.avi and abc.sub]  
in the Program View list.  
Playing JPEG/ Kodak picture CD  
Filter  
IMPORTANT!  
You have to turn on your TV and set to  
the correct Video In channel. (See page  
12, ‘ Finding your viewing channel ‘ ).  
The Toolkit has the following play mode items:  
Filter ( Audio/Photo/Video ): Sets file filters  
(Filter is not applicable to Audio CD.)  
General Operation  
A
Load a disc.  
Repeat (Off/Single/ All):  
The disc reading time may exceed 30 seconds  
due to the complexity of the directory/file  
configuration.  
Off:  
Resumes normal playback  
Single: Repeats the current track/file.  
All:  
Repeats all files on the current folder or all  
tracks on the disc.  
The data disc menu information appears on the  
TV screen.  
Mode(Normal/Shuffle)  
This mode can also be toggled by using RANDOM  
button.  
Normal: Resumes Normal playback  
Shuffle: Playbacks track/file in random order.  
Filter  
Edit Mode: Program operation works only when  
Edit Mode is selected. After finished storing the files/  
tracks you want into the Program View list, select  
“Edit Mode” again and press OK to release edit  
mode.  
B
Press / to select the folder and press OK to  
open the folder.  
Press / to select a file.  
Press OK to confirm.  
Program View: To view tracks/files in the  
Program View list. It is disabled if the Program View  
list is empty.  
C
D
Add To Program: Add files/tracks to the Program  
View list. It is disabled if Edit Mode is not selected.  
(The maximum number of files/tracks can be added  
is 30.)  
Tips:  
- If you highlight on a jpeg file, a preview will appear.  
- During JPEG playback, the LED will display the file  
number.  
Browser View: To view files/tracks in the Original  
View list.  
Playback Selection  
Clear Program: Delete the files/tracks in the  
During playback, you can;  
Helpful hintThe operating features described here might not be possible for certain discs.  
Always refer to the instructions supplied with the discs.  
ꢀꢅ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Menu Options  
Tips:  
Program View list.  
-Some DVD video discs may be set to display  
subtitles in a different language other than  
you selected. A prior subtitle language may be  
programmed on the disc.  
Select a file/track or more you want to delete in  
stop mode.' ' will appear besides the deleted file/  
track.Select Clear Program and then press OK . It is  
disabled if Edit mode is not selected.  
-Some DVD video discs allow you to change subtitle  
selections only via the disc menu. If this is the case,  
press the MENU button and choose the appropriate  
subtitle language from the selection on the disc  
menu.  
Zoom picture ( JPEG)  
During playback, press ZOOM repeatedly to  
display the picture with different scales.  
Use / / / to view the zoomed picture.  
-Some DVD video discs may not be played in a  
different audio language that you selected. A prior  
language may be programmed on the disc.  
-Some DVD discs may not include your pre-selected  
language . In this case, the DVD player  
automatically displays discs menus consistent with  
the disc’s initial language setting.  
Rotate picture (JPEG)  
During playback, press / / / to rotate the  
picture on the TV screen.  
/ flip the picture vertically by 180º  
rotate the picture anti-clockwise by 90º  
rotate the picture clockwise by 90º  
Tip:  
-It may not be possible to play certain JPEG disc due  
to the configuration and characteristics of the disc or  
condition of the recording.  
®
DivX Subtitle  
If your DivX® files include a subtitle file (see page  
17 for the supported file formats), you may select a  
supported DivX® subtitle language by region.  
This DVD Player setup is carried out via the TV,  
enabling you to customise the DVD player to suit  
your particular requirement.  
In ‘Language’, press /to select  
{ DivX Subtitle }, then press .  
A
{
}
Standard  
Albanian, Danish, Dutch, English, Finnish, French, Gaelic,  
German, Italian, Kurdish (Latin), Norwegian, Portuguese,  
Using the Language setup menu  
Spanish, Swedish andTurkish.  
{
}
Central European  
Albanian, Croat, Czech, Dutch, English,  
German, Hungarian, Irish, Polish,  
A
Press SETUP on the remote control.  
The system setup menu appears.  
Romanian, Slovak, Slovene and Sorbian.  
OSD language  
Subtitle  
:English  
:Auto  
Language  
{
}
Cyrillic  
Video  
DivX Subtitle  
Audio  
:Standard  
Bulgarian, Belorussian, English,  
Macedonian, Moldavian, Russian,  
:
:
English  
English  
Audio  
DVD Menu  
Serbian and Ukrainian.  
{ Greek }  
English and Modern Greek only.  
{ Hebrew }  
Rating  
Misc  
English and Modern Hebrew only.  
B
C
Press / to select {Language }, then press .  
Press / to select an item, then press to  
access.  
Use /to select a setting and press  
B
A
OK  
to confirm.  
Example: { OSD Language }  
The options for the selected item appears.  
If the selection in the menu is greyed out, that  
means the feature is not available or not possible to  
change at the current state.  
Use /to select a setting and press OK to  
confirm.  
Using the Video setup menu  
Press SETUP on the remote control.  
D
E
The system setup menu appears.  
Example: { English }  
Language  
4:3  
Aspect Ratio  
View Mode  
TV System  
Video Out  
:
The setting is selected and setup is completed.  
To exit, press SETUP.  
:Auto Fit  
:PAL  
Video  
Audio  
:RGB  
Smart Picture  
:Standard  
OSD Language  
This menu contains various language options for the  
language displayed on the screen.  
Rating  
Misc  
Subtitle/Audio/DVD Menu/DivX Subtitle  
B
C
Press / to select { Video }, then press   
Press / to select an item, then press to  
access.  
These menus contains various language options for  
audio, subtitle, DVD menu and DivX subtitle which  
may be recorded on the DVD.  
Example: { Video Out }  
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢀꢆ  
DVD Menu Options  
A playback picture may be distorted when detected a  
signal change between PAL and NTSC on the disc.  
For the case of Progressive mode, your multisystem  
TV must be able to support 525p and 625p.  
The options for the selected item appears.  
If the selection in the menu is greyed out, that  
means the feature is not available or not possible to  
change at the current state.  
D
E
Use / to select a setting and press OK to  
confirm.  
Example: { P-Scan }  
Video Out  
The video output of the DVD player can be selected  
as “Component”, “RGB” or “P-Scan”.  
In ' Video ', press / to select { Video Out },  
then press .  
The setting is selected and setup is completed.  
To exit, press SETUP.  
A
{ Component }  
Aspect Ratio  
Select this for component video connection.  
{ RGB }  
Select this for Scart connection.  
{ P-Scan }  
Select this when you connect your DVD player to  
your TV, which has component video inputs that  
supports progressive scan.  
Use / to select a setting and press OK to con-  
firm.  
The picture shape can be adjusted to fit your TV and  
the format must be available on the playback disc.  
Otherwise, the TV display will not affect the picture  
during playback.  
In ' Video ', press / to select {Aspect Ratio },  
then press .  
A
{ 4:3 }  
B
A
Select this if you have a normal TV. A 'wide-screen'  
source display with black bars on the top and bottom  
Smart Picture  
will be displayed on the TV screen.  
{ 16:9 }  
This DVD player provides four predefined sets of  
picture color settings.  
In ' Video ', press / to select {Smart Picture },  
then press .  
Select this for wide-screen TV (frame ratio 16:9).  
Use / to select a setting and press OK to  
confirm.  
B
A
{ Standard }  
View Mode  
Use view mode to scale an image that fits to the TV  
screen's width and height.  
In ' Video ', press / to select { View Mode },  
then press .  
{ Fill }  
Select this for a preset standard picture setting.  
{ Vivid }  
Select this to make the picture brighter.  
{ Cool }  
Select this to make the picture softer.  
{ Personal }  
Select this to personalize your picture color by  
adjusting the brightness, contrast, tint and color  
Fill the screen with decoded image.  
{ Original }  
Display image as its original size.  
(saturation).  
Use / to select a setting and press OK to  
confirm.  
If you select { Personal }, then proceed to steps  
D~G.  
{ Height Fit }  
B
C
Fit the screen height with image height.  
{ Width Fit }  
Fit the screen width with image width.  
{ Auto Fit }  
Automatically display the decoded image on screen  
The setup menu appears.  
0
at a suitable size.  
Brightness  
0
{ Pan Scan }  
Automatically display decoded image on full screen  
Contrast  
0
Tint  
0
Color  
without distortion.  
Use / to select a setting and press OK to  
Close  
B
confirm.  
Tip:  
D
Press / to highlight one of the following options.  
Brightness  
-Depending on the type of disc, you may not be able  
to view the mode as selected.  
Increase the value to brighten the picture or vice  
versa. Choose zero (0) for average setting.  
Contrast  
Increase the value to sharpen the picture or vice  
versa. Choose zero (0) to balance the contrast.  
Tint  
Increase the value to darken the picture or vice  
versa. Choose zero (0) for average setting.  
Color  
Increase the value to enhance the colour in your  
picture or vice versa. Choose zero (0) to balance the  
colour.  
TV System  
The video standard of the DVD player output can be  
selected from “NTSC”, “PAL” or “Multi”.  
{ NTSC }: Select if your TV system is NTSC.  
{ PAL }: Select if your TV system is PAL.  
{ Multi }: The DVD video player automatically  
identifies PAL or NTSC video system of a disc.  
Connect a multisystem TV (PAL/NTSC compatible) to  
view a picture.  
E
Press / to adjust the setting that best suits  
your personal preference.  
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
ꢀꢇ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Menu Options  
A
In Audio, press / to select { Night Mode },  
then press .  
{ On }  
Select this to set low volume output. This feature  
is only available for movie discs with Dolby Digital  
F
G
Repeat steps D~ E to adjust your picture  
preference.  
Press / to select Closeand press OK to  
confirm.  
mode.  
{ Off }  
Using the Audio setup menu  
Turns off night mode feature. Select this to enjoy the  
A
Press SETUP on the remote control.  
surround sound with its full dynamic range.  
Use / to select a setting and press OK to  
confirm.  
The system setup menu appears.  
B
A
Digital Output  
: All  
:Off  
: On  
:Off  
Language  
Night Mode  
Down Sampling  
Down Sampling  
You can enable and disable the digital signal for  
better sound output quality.  
In Audio, press / to select { Down  
Sampling }, then press .  
{ Off }  
Video  
3D Effects  
Audio  
Rating  
Misc  
If your amplifier / decoder is compatible with 96 KHz  
PCM, select “ Off “ . Sound is sampled at 96 KHz.  
{ On }  
If your amplifier / decoder is not compatible with 96  
KHz PCM, select “ On “ . Sound recorded at 96 KHz  
is down sampled to 48 KHz.  
B
C
Press / to select { Audio }, then press .  
Press / to select an item, then press to  
access.  
Example: { Night Mode }  
The options for the selected item appears.  
B
Use / to select a setting and press OK to  
confirm.  
Tip:  
If the selection in the menu is greyed out, that  
means the feature is not available or not possible to  
change at the current state.  
- When playing back disc with copyright protection,  
the sound will be down sampled to 48 KHz even  
when you select Down Sampling off.  
D
E
Use / to select a setting and press OK to  
confirm.  
Example: { On }  
The setting is selected and setup is completed.  
To exit, press SETUP.  
3D Effects  
To obtain expansive virtual surround sound effects  
from two speakers, set 3D Effects to on. This  
enhancement sounds only output from the Analogue  
AUDIO OUT (L / R) jacks of the DVD player.  
In 'Audio', press / to select { 3D Effects }, then  
press .You can set to { Off } or { On }.  
Use / to select a setting and press OK to  
confirm.  
Digital Output  
Select this if you connect to a multichannel decoder/  
receiver.  
In 'Audio', press / to select { Digital Output },  
then press .  
A
B
A
{ All }  
Select this if the connected device has a built-in  
multichannel decoder that supports one of the  
multichannel audio format (Dolby Digital, DTS).  
{ PCM }  
Tip:  
- Only effective in playback of a DVD Video disc with  
Dolby Digital 5.1 bitstream.  
Select this if the connected device is not capable of  
decoding multichannel audio. The DVD player will  
convert the Dolby Digital signal to PCM (Pulse Code  
Modulation).  
Using the Rating setup menu  
A
Press SETUP on the remote control.  
{ Off }  
The system setup menu appears.  
To deactivate the digital audio output. For example, if  
you use the AUDIO OUT jacks to connect to a TV or  
stereo system.  
Parental control  
: 8.Aduit  
Language  
Video  
Set Password  
B
Use / to select a setting and press OK to  
confirm.  
Audio  
Rating  
Tip:  
Misc  
-When playing MPEG and set Digital Output to {All},  
the player will output PCM signals.  
B
C
Press / to select {Rating }, then press .  
Press / to select an item, then press to  
access.  
Night Mode  
This mode optimizes playback of sound at low  
volume. High volume outputs will be softened and  
low volume outputs are brought upward to an audible  
level.  
Example: { Parental control }  
The options for the selected item appears.  
If the selection in the menu is greyed out, that  
means the feature is not available or not possible to  
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢁ0  
DVD Menu Options  
then press OK.  
change at the current state.  
You will be prompted to enter your four-digit  
password.  
D
Use / to select a setting and press OK to  
confirm.  
Example: { 8 Adult }  
Enter Password  
The setting is selected and setup is completed.  
E
To exit, press SETUP.  
B
Use the number buttons ( 0-9 ) to enter the four-digit  
password.  
Rating Level settings  
When doing this for the first time, enter the default  
password 0000 .  
If you forget your old four-digit password, enter the  
default password 0000.  
Press OK again to enter the new four-digit password.  
Depending on the DVD, you may be asked to  
change the parental level while playing the disc. The  
rating levels are from 1 to 8 and are country  
dependent. You can prohibit the playing of certain  
discs that are not suitable for your children, or have  
certain discs played with alternative scenes.  
In ' Rating ', press / to select {Parental control },  
then press .  
C
D
The new four-digit password will now take effect.  
Enter New Password  
A
B
Use the number buttons to enter the four-digit  
password, then press OK.(See ‘Changing the  
Password’ on this page.)  
Press OK to confirm.  
C
Press OK again to list the parental level.  
{ 1.Kid Safe }  
Suitable for children.  
{ 2. G }  
Using the Misc (Miscellaneous) setup  
General Audience; recommended as acceptable for  
viewers of all ages.  
menu  
{ 3. PG }  
Parental Guidance suggested.  
A
Press SETUP on the remote control.  
The system setup menu appears.  
{ 4. PG-13 }  
Use Default Settings  
Language  
Unsuitable for children under 13.  
{ 5. PG-R }  
DivX Registration  
Video  
Parental Guidance Recommended.  
Audio  
Rating  
{ 6. R }  
Restricted; under 17 requires accompanying parent  
or adult guardian.  
Misc  
{ 7. NC-17 }  
No one under 17 admitted.  
{ 8. Adult }  
DVD softwares of any grades (adult/general/children)  
can be played back. Should be viewed only by adults  
due to graphic sexual material, violence or language.  
Use / to select a rating level and press OK to  
confirm.  
B
C
Press / to select { Misc }, then press .  
Press / to select an item, then press OK to  
access.  
Example: { Use Default Settings }  
The options for the selected item appears.  
If the selection in the menu is greyed out, that  
means the feature is not available or not possible to  
change at the current state.  
Use/ to select a setting and press OK to  
confirm.  
D
Select { 8 Adult } to disable parental level and  
allow all discs to play.  
D
E
DVDs that are rated higher than the level you  
selected will not play unless you enter your four-digit  
password.  
Example: { No }  
The setting is selected and setup is completed.  
To exit, press SETUP.  
Tips:  
Restoring to original settings  
-This feature will not limit viewing if the disc  
manufacturer did not code the disc.  
-VCD, SVCD, CD have no level indication, so  
parental control has no effect on these type of discs.  
This also applies to most illegal DVDs.  
-Some DVDs are not coded with a rating though the  
movie rating may be printed on the disc cover. The  
rating level feature does not prohibit play of such  
discs.  
Setting the { Use Default Settings } function will reset  
all options and your personal settings to the factory  
defaults, except your password and rating level.  
In Misc, press / to select  
A
{ Use Default Settings }, then press OK.  
The menu will appear.  
Use Default Settings  
Changing the Password  
Yes  
No  
You need to enter your four-digit password to play a  
prohibited disc or if prompted for a password.  
In Rating, press / to select {Set Password },  
{ Yes }  
Select this to reset to factory default settings.  
A
Helpful hint: Press to go back to previous menu item.  
Press SETUP to exit the menu item.  
ꢁꢀ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Menu Options  
{ No }  
Select this to close the menu.  
Use / to select a setting and press OK to  
confirm.  
Tray Lock  
B
DivX® Registration  
Press SETUP button, then press the number button  
"2006" in sequence to lock the tray.  
®
DivX registration code allows you to rent and  
All functionality of the player and playback remain  
the same except for the OPEN/CLOSE button.  
After the tray is locked, "Tray Lock Is On" will  
appear on the screen when OPEN/CLOSE is  
pressed.  
®
purchase movies using the DivX VOD service from  
the internet.  
For more information, visit website:  
To unlock the tray, just follow the same procedure  
as above.  
A
B
In ‘Misc’, press /to select  
{ DivX Registration }, then press OK.  
The registration code will appear.  
Use the registration code to rent or purchase the  
®
movies from DivX VOD.  
Follow the instructions and download the movie  
from your computer onto a CD-R/RW for playback on  
this DVD player.  
Tips:  
®
All the downloaded movies from DivX Registration  
can only be played back on this DVD player.  
®
Time search feature is not available during DivX  
movie playback.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢁꢁ  
Specifications  
DVD Player/Outputs/Supplied Accessories  
DVD Player  
Power supply  
110 V - 240 V AC, 50/60 Hz  
Power Consumption  
12W( standby :<3W)  
Net weight  
1.35 kg  
External dismensions  
Signal System  
Laser  
360 X 43 X 209 mm (W/H/D)  
PAL, NTSC  
Semiconductor laser, wavelength 650/780 nm  
Frequency range  
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz  
96 kHz sampling 4 Hz to 44 kHz  
Signal-to-noise ratio  
Audio dynamic range  
Harmonic distortion  
Wow and flutter  
More than 90 dB  
More than 80 dB  
Less than -65 dB  
Below measurable level [(less than 0.001 % ( W.PEAK )]  
O
O
Operating conditions  
Temperature : 5 C to 35 C Operation status :Horizontal  
Outputs  
Video output  
1.0 V ( p-p ) , 75 Ω negative sync., pin jack x 1  
Video output (SCART)  
Component video output  
1.0 V ( p-p ) , 75 Ω, SCART socket x 1  
(Y) 1.0 (p-p), 75 Ω negative sync., pin jack x 1  
(P B)/(P R) 700 mV (p-p), 75 Ω, pin jack x 2  
Audio output (SCART)  
2.0 (rms), 680 Ω, SCART socket x 1  
Audio output ( COAXIAL DIGITAL ) 0.5 V (p-p) 75 Ω pin jack x 1  
Audio output (ANALOG)  
2.0 V (rms), 680 Ω, pin jacks (L/R) x 1  
Supplied Accessories  
Remote control(SE-R0301)  
Batteries(AAA)  
The model complies with the above specifications.  
Designs and specifications are subject to change without notice.  
This model may not be compatible with features and /or specifications that may be added in the future.  
ꢁꢂ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
WARNING  
Under no circumstances should you try to repair the DVD player yourself, as this will invalidate the  
warranty. Do not open the DVD player as there is a risk of electric shock.  
If a fault occurs, first check the points listed below before taking the DVD player for repair. If you are unable  
to remedy a problem by following these guides, consult your dealer or TOSHIBA for help.  
Problem  
No power  
Solution  
-Check if theAC power cord is properly connected.  
-Press the I/2ON/STANDBY on the front of the DVD player  
to turn on the power.  
-Refer to your TV' s manual for correct Video In channel  
selection. Change the TV channel until you see the DVD  
screen.  
No picture  
-Check if the TV is switched on.  
-If the progressive scan feature is activated but the connected  
TV does not support progressive signals or the cables are  
not connected accordingly. See pages 12-13 for proper  
progressive scan set up or deactivate the progressive scan  
feature as follow:  
1) Press OPEN/CLOSE on the DVD Player.  
2) When the disc tray is opened, press number button1on  
the remote control for a few seconds.  
Distorted picture  
Picture clipped  
-Sometimes a small amount of picture distortion may  
appear depending on the disc being played back. This is not  
malfunction.  
-May be caused by View Mode Setting (see page 19). Set to  
Original for normal viewing.  
-Connect DVD Player directly to the TV.  
Completely distorted picture or  
black /white picture with DVD.  
-Make sure the disc is compatible with the DVD player.  
-Ensure that the DVD Player's setting is set to match that of  
the disc and your TV.  
-Adjust the volume.  
-Check that the speakers are connected correctly.  
No sound / distorted sound  
No audio at digital output  
-Check the digital connections.  
-Check if your receiver can decode MPEG-2 or DTS and if not,  
please make sure the digital output is set to PCM.  
-Check if the audio format of the selected audio language  
matches your receiver capabilities.  
-Check that the cable is connected to the correct device (See  
Connecting to television).  
No sound and picture  
Disc cannot be played  
-The DVD+R/RW must be finalized.  
-Ensure the disc label is facing up.  
-Check if the disc is defective by trying another disc.  
-Wrong region code.  
-Check the disc for fingerprint/scratches and clean with a soft  
cloth wiping from centre to edge.  
Picture freezes momentarily during playback  
No return to start-up screen when disc is removed  
-Reset the unit by switching the player off, then on again.  
-Aim the Remote Control directly at the sensor on the front of  
the player.  
The player does not respond to the Remote Control  
-Reduce the distance to the player.  
-Replace the batteries in Remote Control.  
-Re-insert the batteries with their polarities(+/- signs)as  
indicated.  
Buttons do not work  
-To completely reset the player, unplug theAC cord fromAC  
outlet for 5-10 seconds.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢁꢃ  
Troubleshooting  
Problem  
Solution  
Player does not respond to some operating  
commands during playback.  
-Operations may not be permitted by the disc.  
Refer to the instructions of the disc jacket.  
DVD Player cannot read CDs /DVDs  
Menu items cannot be selected  
-Use a commonly available cleaning CD/DVD to clean  
the lens before sending the DVD Player for repair.  
-Press STOP twice before selecting system setup  
menu.  
-Depending on the disc availability,some menu items  
cannot be selected.  
Unable to select Progressive Scan on/off  
-Ensure that the output of the Video Out signal is  
switch to P-Scan/Component.  
ꢁꢈ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Glossary  
®
Analogue audio:  
Progressive scan:  
DivX :  
An electrical signal that directly  
represents sound. In contrast,  
digital audio can also be an electrical  
signal, but is an indirect  
representation of sound. See also  
Digital audio.  
It displays all the horizontal lines  
of a picture at one time, as a signal  
frame. This system can convert  
the interlaced video from DVD into  
progressive format for connection to  
a progressive display. It dramatically  
increases the vertical resolution.  
DivX® is a codec (compression/de-  
compression) that can compress im-  
ages to a very small amount of data.  
®
Dolby Digital:  
A system developed by Dolby  
Laboratories that compresses  
digital sound. It works with stereo  
(2ch) or multi-channel audio.  
Aspect ratio:  
PCM:  
The width of a TV screen relative to  
it is height. Conventional TVs are 4:3  
(i.e., the screen is almost square).  
Widescreen models are 16:9 (the  
screen is almost twice as wide as its  
height)  
(Pulse Code Modulation)  
PCM is a format that converts audio  
into digital data. It is mainly used for  
Audio CDs and DAT. This unit can  
play back sounds as realistic as  
®
DTS :  
(Digital Theater System)  
DTS is a Multi-channel surround  
sound system, but it is different from  
Dolby Digital. Both formats were  
developed by Digital Theater  
Systems, Inc.  
possible by converting even com-  
pressed Dolby Digital and MPEG  
audio to PCM.  
Chapter:  
Just as a book is split up into  
several chapters, a title on a DVD  
disc is usually divided into chapters.  
See also Title.  
Region code:  
JPEG:  
Regions associate discs and  
players with particular areas of the  
world. This unit will only play back  
(Joint Photographic Experts Group)  
AUDIO OUT jacks:  
JPEG is a method of compressing  
still image files. You can copy JPEG  
files on CD-RW / R discs from a  
computer and play back the files on  
this unit.  
Jacks on the back of the DVD System  
that send audio to another system (TV,  
Stereo, etc.)  
discs that have compatible region  
codes. You can find the region code  
of your unit by looking on the rear  
panel. Some discs are compatible  
with more than one region (or all  
regions).  
Bite rate:  
The amount of data used to hold a  
given length of music; measured in  
kilobits per seconds, or kbps. Or, the  
speed at which you record.Generally,  
the higher the bite rate,or the higher the  
recording speed, the better the sound  
quality. However, higher bite rates use  
more space on a disc.  
Multichannel:  
DVD is specified to have each sound  
track constitute one sound field. Multi-  
channel refers to a structure of sound  
tracks having three or more channels.  
Sampling frequency:  
The rate at which sound is  
measured by a specified interval to  
turn it into digital audio data. The  
number of samples in one second is  
defined as the sampling frequency.  
The higher the rate is, the better the  
possible sound quality.  
Parental control:  
A function of the DVD to limit playback  
of the disc by the age of the users  
according to the limitation level in each  
country. The limitation varies from disc  
to disc; when it is activated, playback  
will be prohibited if the software’s level  
is higher than the user-set level.  
Disc menu:  
A screen display prepared for  
allowing of selection of images, sound,  
subtitle,multi-angles etc. recorded on  
the DVD.  
Title:  
(DVD)  
A collection of chapters on a DVD.  
See also chapter.  
Digital audio:  
PBC (Video CD only):  
(Playback Control)  
An indirect representation of sound  
using numbers. During recording,  
the sound is measured at discrete  
intervals (44, 100 times a second  
for CD audio) by an analogue-to  
-digital converter, generating a  
stream of numbers. On playback, a  
digital-to-analogue converter  
generates an analogue signal based on  
these numbers. See also  
(Video CD)  
This function enables you to play  
back interactive software using a  
menu screen. See also Title.  
The contents of a Video CD. When  
playing back a Video CD with the  
PBC function, the title menu will  
appear automatically.  
Track:  
Audio CDs and Video CDs use  
tracks to divide the contents of a  
Sampling frequency and Analogue  
audio.  
disc. The DVD equivalent is called a  
chapter. See also Chapter.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ꢁꢄ  

Technicolor Thomson DVD Player DTH111E User Manual
Technika Stereo System MC 429ID User Manual
Toshiba DVD Player SD P1400 User Manual
Toshiba Network Card EQPIII 840 User Manual
Tripp Lite Switch B013 330 User Manual
Troy Bilt Trimmer TB32 EC User Manual
Universal Carbon Monoxide Alarm CD 9775 User Manual
Univex Treadmill TR9100 Series User Manual
ViewSonic MP3 Player NMP 500 User Manual
VTech Cordless Telephone VT5875 User Manual