TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366
(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152
Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471
INSTALLATION MANUAL FOR TGU MODELS
(TRUE GASTRONORM UNDERCOUNTER & WORKTOP
REFRIGERATORS / FREEZERS)
TABLE OF CONTENTS
TGU-2
Safety Information
Safety Precautions ––––––––––––––––––––––––1
Proper Disposal –––––––––––––––––––––––––––2
Connecting Electricity ––––––––––––––––––––––3
Adapter Plugs ––––––––––––––––––––––––––––3
Installation / Operation Instructions
Ownership ––––––––––––––––––––––––––––––– 4
Required Tools –––––––––––––––––––––––––––– 4
Uncrating & Locating ––––––––––––––––––––––– 4
Installation of Leg/Castors –––––––––––––––––– 5
Leveling Cabinet –––––––––––––––––––––––––– 6
Electrical Instructions––––––––––––––––––––––– 6
Start-up ––––––––––––––––––––––––––––––––– 7
Shelving Installation - Operation –––––––––––––– 8
TGU-3F
Maintenance, Care & Cleaning
Cleaning Condenser Coil –––––––––––––––––––– 9
Stainless Steel Equipment Care & Cleaning –––– 10
*Spanish, German, French, and Dutch versions included.
CONGRATULATIONS!
You have just purchased the finest commercial
refrigeration available. You can expect many years
of trouble-free operation.
TRUE GASTRONORM
UNDERCOUNTER & WORKTOP
REFRIGERATORS / FREEZERS
SB #912630
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
How to Maintain Your
Unit
to Receive the Most Efficient and
Successful Operation
You have selected one of the finest commercial refrigeration units made. It is manufactured under
strict quality controls with only the best quality materials available. Your TRUE cooler, when
properly maintained, will give you many years of trouble-free service.
WARNING!
Use this appliance for its intended purpose as described in this Owner Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
• This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
NOTE: Any servicing, warranty repairs or maintenance
should be carried out by qualified personnel, failure
to do so could be dangerous and may invalidate your
warranty.
• Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
• Unplug the refrigerator before cleaning and
making repairs.
• Setting temperature controls to 0 position does
not isolate the unit from the electrical supply,
you must disconnect the main power lead from
the wall receptacle to isolate.
• Do not touch the cold surfaces in the
refrigerated compartment when hands are damp
or wet. Skin may stick to these extremely cold
surfaces.
• Do not store or use flammable liquids or vapors
in the vicinity of this or any other appliance.
• Keep fingers out of the“pinch point”areas;
clearances between the doors and cabinet are
necessarily small; be careful closing doors when
children are in the area.
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
DANGER!
RISK OF CHILD ENTRAPMENT
HOW TO SAFELY DISPOSE OF USED
REFRIGERATION EQUIPMENT
Child entrapment and suffocation are not problems
of the past. Junked or abandoned display cases are
still dangerous… even if they will sit for“just a few
days.”
Refrigerant Disposal
Depending on the country where the unit is located
there will be Officially approved way of disposing
of your used equipment. Your old refrigerator may
have a cooling system that uses“Ozone Depleting
”chemicals. If you are throwing away your old
refrigerator, make sure the refrigerant is removed for
proper disposal by a qualified service technician. If
you intentionally release any refrigerants you can be
subject to fines and imprisonment under provisions
of the environmental regulations.
It is much safer if doors and lids are removed so
children cannot get trapped inside, leaving the
shelves in place will also deter children from trying to
climb inside.
If you are getting rid of your old display case, please
follow the instructions below to help prevent
accidents. Depending on the country where the
unit is located there will be officially approved ways
of disposing of your used equipment.
It is important that care is taken in disposing of used
refrigerators or freezers. Before You Throw Away Your
Old Refrigerator or Freezer:
• Take off the doors.
• Leave the shelves in place so that children may
not easily climb inside.
2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
SAFETY INFORMATION
WARNING!
IMPORTANT ELECTRICAL SAFETY INFORMATION
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
Your TRUE unit will come fitted with the correct
plug for your Country (if not contact your
supplying dealer). This plug has a ground or earth
prong or pin, it must be connected to a electrical
supply outlet that is also grounding or earthed.
This minimizes the possibility of electric shock
hazard. Do not connect to any power supply if you
have any doubts. Make sure a qualified electrician
confirms that the supply is grounded or earthed.
Ensure that the supply is correct and matches that
on the unit information plate. Do not use adapter
plugs or extension leads as these can cause safety
issues and early failure of electrical components.
The use of adapters and extension cords will
invalidate your warranty. Always disconnect the
unit by pulling on the plug and not on the power
lead. Do not use the unit if the power lead has
been damaged.
USE OF EXTENSION CORDS / ADAPTER PLUGS
Do not use adapter plugs or extension leads as these can cause safety issues and early failure of electrical components.
The use of adapters and extension cords will invalidate your warranty. NEVER USE AN EXTENSION CORD! NEVER USE AN
ADAPTER PLUG!
WARNING
Compressor warranties are void if compressor burns out due to low voltage.
WARNING
Power supply cord ground should not be removed!
NOTE
To reference wiring diagram - Remove lower rear grill. Wiring diagram is positioned on the inside cabinet wall.
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION / OPERATION INSTRUCTIONS
OWNERSHIP
To insure that your unit works properly from the
first day, it must be installed properly. We highly
recommend that your True unit is installed by your
supplying dealer or service company. The cost of a
professional installation is money well spent. Issues
caused by incorrect installation may invalidate your
warranty
Before you start to install your True unit, carefully
inspect it for freight damage. If damage is
discovered, immediately file a claim with the
delivery freight carrier or supplying dealer.
True is not responsible for damage incurred during
shipment.
REQUIRED TOOLS
• Adjustable Spanner or Mole Grips
• Phillips Head Screwdriver
• Spirit Level
UNCRATING
Step 1
C. Move your unit as close to the final location as
possible before removing the wooden skid.
The following procedure is recommended for
uncrating the unit:
Note: Keys for coolers with door locks are located in
warranty packets.
A. Remove the outer packaging by pulling tri-wall
nails from skid. Remove (4) cardboard corner
pads and dust cover.
B. Inspect for concealed damage. Again,
immediately file a claim with the freight carrier
if there is damage.
LOCATING
Step 2
A. Remove packing material behind cabinet as a
cushion. Carefully lay the unit on its back to
remove skid.
Removing skid
from bottom of
cabinet.
When lifting unit remember to leave the
cabinet upright for 24 hours before
plugging into power source.
B. Remove skid by unscrewing all base rail anchor
brackets. Place skid to the side.
C. Carefully lift cabinet upright.
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION OF LEGS AND CASTORS
Step 3
A. Turn the bearing race counter-clockwise until
the cabinet is level. Level front to back and side to
side. (diagonally)
Securing Castors:
To obtain maximum strength and stability of the
unit, it is important that you make sure each castor
is secure. The bearing race on the castor of the top
edge of the leg must make firm contact with the
rail.
B. Install the desired number of shims, making sure
the slot of the shim is in contact with the threaded
stem of the castor.
C. If more than one shim is used, turn the slot at a
90° angle so they are not in line.
Unit Leveling:
D. Turn the bearing race clockwise to tighten and
secure the castor by tightening the anchoring bolt
with a 3/4 inch open-end wrench, socket, or the
tool provided.
Four leveling shims have been provided for leveling
castored units positioned on uneven floors. Shims
must be positioned between rail end and bearing race.
True recommends a four shim limit to any single castor.
CAUTION
To avoid damage to lower rail assembly, slowly raise
unit to upright position after installing castors.
1
2
Anchor the four screws firmly to
the base of the unit.
Thread four screws into castor in
the underside of cabinet frame
rail.
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LEVELING
Step 4
D. Ensure that the drain hose or hoses are
positioned in the pan.
E. Free plug and cord from inside the lower rear of
the cooler (do not plug in).
F. The unit should be placed close enough to the
electrical supply so that extension cords are never
used.
A. Set unit in its final location. Be sure there is
adequate ventilation in your room. Under extreme
heat conditions, (100°F+, 38°C+), you may want to
install an exhaust fan.
Warning
Warranty is void if ventilation is insufficient.
Warning
B. Proper leveling of yourTrue cooler is critical to
operating success (for non-mobile models). Effective
condensate removal and door operation will be
effected by leveling.
Compressor warranties are void if the unit is more than 7ft.
(2.1m) from plug-in connection. TRUE will not warranty any
units that are connected to an extension cord.
C. The cooler should be leveled inside the cabinet
front to back and side to side with a level.
ELECTRICAL INSTRUCTIONS
Step 5
A. Before your new unit is connected to a power
supply, check the incoming voltage with a
voltmeter. If anything less than 100% of the
rated voltage for operation is noted, correct
immediately.
WARNING
Compressor warranties are void if compressor burns out due to
low voltage.
WARNING
Power supply cord ground should not be removed!
B. All units are equipped with a 7 ft. (2.1m) service
cord, and must be powered at proper operating
voltage at all times. Refer to cabinet data plate
for this voltage.
NOTE
To reference wiring diagram - Remove lower rear grill. Wiring
diagram is positioned on the inside cabinet wall.
True requires that a sole circuit be dedicated for the
unit. Failure to do so voids warranty.
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
STARTUP
Step 6
NOTE
If the unit is disconnected or shut off, wait five minutes before
starting again.
A. The compressor is ready to operate. Plug in the
unit.
B. Temperature control set at No. 4 position gives
refrigerators an approximate temperature of
35°F (1.6˚C) and freezers an approximate
temperature of -10°F (-23.3˚C). Allow unit
to function several hours, completely cooling
cabinet before changing the control setting.
RECOMMENDATION
Before loading product we recommend you run your True
unit empty for two to three days. This allows you to be sure
electrical wiring and installation are correct and no shipping
damage has occurred. Remember, our factory warranty does not
cover product loss!
C. Excessive tampering with the control could lead
to service difficulties. Should it ever become
necessary to replace temperature control, be
sure it is ordered from your True dealer or
recommended service agent.
REPLACEMENT PARTS
TRUE maintains a record of the cabinet serial number for your
unit. If at any time during the life of your display case, a part
is needed, you may obtain this part by furnishing the model
number and serial number to the company from whom you
purchased the cabinet. Call Toll-Free: (800)-424-TRUE (Direct
to Parts Department). (800)-325-6152 (U.S.A. & Canada only)
or call: (636)-240-2400.
D. Good air flow in your True unit is critical. Be
careful to load product so that it neither presses
against the back wall, nor comes within four
inches of the evaporator housing. Refrigerated
air off the coil must circulate down the back
wall.
Serial Number
REMOTE UNITS (This section applies to remotes only!)
• Remote cabinets must be ordered as remote.
We do not recommend converting from a
standard self contained to remote system.
• Contact True Technical Service for BTU
requirements.
• No wiring necessary between cabinet and
condensing unit.
• All remote cabinets must be hard wired.
• No castors available.
• All remote condensing units purchased from
True are 208/230 volts single phase.
• All remote cabinets come standard using 404A
refrigerant.
If you have any questions regarding this section,
please call True at 1-(800)-325-6152.
• All remote units come standard with expansion
valve, liquid line solenoid, heated condensate
pan, and defrost timer when applicable.
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
SHELVING INSTALLATION / OPERATION
REQUIRED TOOLS:
• Tray Slide
Step 1
Position tray slide to align front to back (level)
with rectangular hole of the standard posts.
Make sure tabs on the back-side of the tray slide
are facing down. Push in and slide down on
both ends so tabs are in the locked position.
(See figure 1).
Note
Tray
Slide
Make sure that pan slide is level front to back
within the refrigerator or freezer.
Step 2
Repeat procedure with remaining tray slides.
Note
Figure 1
Figure 2 illustrates correct installation of tray slide.
Tray Slide
Figure 2
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
CLEANING THE CONDENSER COIL
When using electrical appliances, basic safety precautions should be followed, including the following
TOOLS REQUIRED:
• Phillips screwdriver
• Stiff bristle brush
• Adjustable Spanner or Mole Grips
• Vacuum Cleaner
Step 1
Image 1
Image 2
Disconnect power to unit.
Step 2
Removing the four Phillips screws to allow
removal of the front grill.
Step 3
Remove bolts anchoring compressor assembly
to frame rails and carefully slide out. (tube
connections are flexible)
Step 4
Clean off accumulated dirt from the condenser
coil and the fan with a stiff bristle brush.
(See image 1).
Image 3
THE CLEANING OF THE CONDENSER IS NOT
COVERED BY THE WARRANTY!
Condensers accumulate dirt and require cleaning every 30 days.
Dirty condensers result in compressor failure, product loss, and
lost sales... which are not covered by warranty.
Step 5
Lift cardboard cover above fan at plastic plugs
and carefully clean condenser coil and fan blades.
Step 6
After brushing condenser coil vacuum dirt from
coil, and interior floor. (See image 2).
If you keep the Condenser clean you will minimize your service
expense and lower your electrical costs. The Condenser requires
scheduled cleaning every thirty days or as needed.
Step 7
Replace cardboard cover. Carefully slide
compressor assembly back into position and
replace bolts.
Air is pulled through the Condenser continuously, along with dust,
lint, grease, etc.
Step 8
Reinstall rear grill assembly onto unit. Tighten all
screws.
A dirty Condenser can result in NON-WARRANTEED part &
Compressor Failures, Product Loss, and Lost Sales.
Step 9
Proper cleaning involves removing dust from the Condenser. By
using a soft brush, or vacuuming the Condenser with a shop vac,
or using CO2, nitrogen, or pressurized air.
Connect unit to power and check to see if
compressor is running.
If you cannot remove the dirt adequately, please call your refrig-
eration service company.
If you have any questions, please call True Manufacturing at 636-
240-2400 or 800-325-6152 and ask for the Service Department.
Service Department Availability Monday-Friday 7:30 a.m. to 5:30
p.m. and Saturday 7:45 a.m. to 11:45 a.m. CST.
9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
STAINLESS STEEL EQUIPMENT CARE AND CLEANING
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces. Please
ensure that you use appropriate products when cleaning and polishing your True unit. Cleaners containing chlorine
must not be used as these will attack the stainless steel causing damage and in some cases corrosion. Your supplier of
cleaning products should be able to advise you of the products suitable to keep your True unit looking like new.
• Stainless Steel Opponents
There are three basic things which can break down your stainless steel’s passivity layer and allow
corrosion to rear its ugly head.
1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
2) Deposits left on your stainless steel can leave spots. You may have hard or soft water depending on
what part of the country you live in. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit too long. These deposits can cause the passive layer to break down and
rust your stainless steel. All deposits left from food prep or service should be removed as soon as
possible.
3) Chlorides are present in table salt, food, and water. Household and industrial cleaners are the worst
type of chlorides to use.
8 steps that can help prevent rust on stainless steel:
1. Using the correct cleaning tools
Use non-abrasive tools when cleaning your stainless steel products. The stainless steel’s passive layer will not
be harmed by soft cloths and plastic scouring pads. Step 2 tells you how to find the polishing marks.
2. Cleaning along the polish lines
Polishing lines or“grain”are visible on some stainless steels. Always scrub parallel to visible lines on some
stainless steels. Use a plastic scouring pad or soft cloth when you cannot see the grain.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners
While many traditional cleaners are loaded with chlorides, the industry is providing an ever increasing choice
of non-chloride cleaners. If you are not sure of your cleaner’s chloride content contact your cleaner supplier.
If they tell you that your present cleaner contains chlorides, ask if they have an alternative. Avoid cleaners
containing quaternary salts as they can attack stainless steel, causing pitting and rusting.
4. Water Treatment
To reduce deposits, soften the hard water when possible. Installation of certain filters can remove corrosive
and distasteful elements. Salts in a properly maintained water softener can be to your advantage. Contact a
treatment specialist if you are not sure of the proper water treatment.
5. Maintaining the cleanliness of your food equipment
Use cleaners at recommended strength (alkaline, alkaline chlorinated or non-chloride). Avoid build-up of hard
stains by cleaning frequently. When boiling water with your stainless steel equipment, the single most likely
cause of damage is chlorides in the water. Heating any cleaners containing chlorides will have the same
damaging effects.
6. Rinse
When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe standing
cleaning agents and water as soon as possible. Allow the stainless steel equipment to air dry. Oxygen helps
maintain the passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel
8. Regularly restore/passivate stainless steel
10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|