INSTRUCTION BOOK
Dishwasher
DH 103
1 06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
In daily use
G Check if it’s necessary to refill with special salt or rinse aid
G Load cutlery and dishes into the dishwasher.
G Fill with dishwasher detergent .
Loading cutlery and dishes
Sponges, household cloths and any object that can
absorb water may not be washed in the dishwasher.
G Select a wash programme suitable for the cutlery and
G Before loading the dishes, you should:
- Remove large left-overs.
dishes.
G Start the wash programme.
- Soften remnants of burnt food in pans
G When loading the dishes and cutlery, please note:
- Dishes and cutlery must not impede the rotation of the
spray arms .
- Load hollow items such as cups, glasses, pans, etc. with
the opening downwards so that water cannot collect in the
container or a deep base.
- Dishes and items of cutlery must not lie inside one
another, or cover each other.
- To avoid damage to glasses, they must not touch.
- Lay small objects in the cutlery basket.
G Plastic items and pans with teflon have a tendency to
retain water drops; these items will not dry as well as
porcelain and steel items.
For washing in the dishwasher the following cutlery/dishes
are not suitable:
are of limited suitability:
- Cutlery with wooden, horn, china or
mother-of-pearl handles
- Only wash stoneware in the dishwasher if it is specifically
marked as being dishwasher-safe by the manufacturer.
- Plastic items that are not heat resistant
- Glazed patterns may fade if machine washed frequently
- Older cutlery with glued parts that is not
temperature resistant
- Silver and aluminium parts have a tendency to discolour
during washing. Left-overs, e.g. egg white, egg yolk and
mustard often cause discolouring and staining on silver.
Therefore always clean left-overs from silver immediately, if
it is not to be washed straight after use.
- Bonded cutlery items or dishes
- Pewter or copper items
- Lead crystal glass
- Some types of glass can become dull after a large number
of washes
- Steel items subject to rusting
- Wooden platters
- Items made from synthetic fibres
Open the door and slide out the baskets to load the dishes.
The cutlery basket
Long bladed knives stored in an upright position are a
potential hazard.
Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as
knives.
The lower basket
The lower basket is designed to take saucepans, lids, plates,
salad bowls, cutlery etc.
Serving dishes and large lids should be arranged around the
edge of the basket, ensuring that the upper spray arm can turn
freely.
Cutlery should be placed in the removable cutlery basket with
the handles facing downwards. If the handles protrude from
the bottom of the basket, obstructing the lower spray arm, load
the cutlery with the handles facing upwards.
Mix spoons with other cutlery
to prevent them from sticking
together.
For best results we
recommend you to use the
cutlery grid provided (if the
size and dimensions of the
cutlery allow it).
UI71
UI49
UI19
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The upper basket
Adjusting the height of the upper basket
The upper basket is designed for plates (dessert plates,
saucers, dinner plates of up to 24 cm in diameter), salad
bowls, cups and glasses.
If washing very large plates you can load them in the lower
basket after moving the upper basket to the higher position.
Arrange items on and underneath the cup rack so that water
can reach all surfaces.
Maximum height of the dishes in
upper basket
lower basket
Glasses with long stems can
be placed upside down in the
cup rack.
With upper basket raised
With upper basket lowered
20 cm
24 cm
31 cm
27 cm
Light items (plastic bowls
etc.) must be loaded in the
upper basket and arranged
so they do not move.
To move to the higher position proceed as
follows:
1. Move the front runner stops (A) of the upper basket
US64
outwards and slide the basket out.
2. Refit the basket in the higher position and replace the stops
In case that plates are loaded in the upper
(A) in their original position.
basket:
load them starting from the
rear positions of the basket;
tilting them slightly forwards
and avoiding the front
positions near the door.
US71
RC01
Before closing the door, ensure that the spray arms can
rotate freely.
After loading your machine always close the door, as an
open door can be a hazard.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Starting position
of the
(3) Consumption values
Programme
Type of load
and
Cycle
description
Energy
Water
Programme
duration
(in minutes)
programme
selector dial
degree of soil
consumption consumption
(in kWh)
0,1
(litres)
Any.
1 cold rinse (to avoid
food scraps from
sticking together).
Partial load (to be
completed later in
the day).
12
10
RINSE & HOLD
1
2
Cold prewash
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying
Heavy soil.
Crockery, cutlery,
pots and pans
(1) POWER WASH
110 - 120
1,15 - 1,24
16 - 18
65°
Main wash up to 65°C
1 cold rinse
1 hot rinse
NORMAL WASH Normal soil.
95 - 105
30 - 40
1,15 - 1,24
1,05 - 1,15
13 - 15
11 - 13
3
4
Crockery and cutlery
65°
Drying
Main wash up to 65°C
1 hot rinse
Fresh soil.
Crockery and cutlery
(2) ECO WASH
(1) Testing programme for EN 50242 (see "Hints for Test Centres).
(2) Ideal for washing crockery and cutlery of breakfast and dinner (fresh soil).
Characterised by a short duration.
This is the perfect daily programme, made to meet the needs of a family of 4 persons who only wish to load breakfast
and dinner crockery and cutlery.
(3) The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by
the variations of the power supply.
For best results we recommend the use of Finish detergents, rinse aid and salt.
P OURING
PACK
W
E
L
N
OUB
N
O
I
CT
E
A
D
L
I
Q
U
I
D
G
E
L
P
O
W
D
E
R
R
I
N
S
E
CONCENTRATED DISHWASHER DETERGENT
DE15
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting a washing programme
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Close the dishwasher door
4. Setting and starting the programme
Turn the programme selector dial clockwise until the
letter of the programme you wish to select corresponds
with the programme marker on the control panel (see
"Washing programmes" chart).
Depress the "Mains on" push button; the "Mains on"
indicator light will come on and the machine will start.
5. Interrupting a washing programme
Interrupt a washing programme in progress ONLY if
it’s absolutely necessary
To interrupt a washing programme
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
G Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the
point in which it was interrupted.
G Press the On/Off push button (in this case the On/Off
indicator light turns off). Press the On/Off push button
again; the programme will start from the point in
which it was interrupted.
6. End of the washing programme
The dishwasher will automatically stop.
Switch off the dishwasher by pressing the "Mains on"
push button, the "Mains on" indicator light turns off.
Open the door and wait a few minutes before removing
the dishes; in this way they will be cooler and the drying
will be improved.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting under a counter
Levelling
(kitchen worktop or sink)
Good levelling is essential for correct closure and sealing of
the door.
By removing the machine’s worktop, you can install it under a
close fitting sink unit or a pre-existing top, providing the
dimensions of the recess correspond to those shown in the
picture.
When the appliance is correctly levelled, the door will not catch
on either side of the cabinet.
If the door does not close correctly, loosen or tighten the
adjustable feet until the machine is perfectly level.
600
IN05
Proceed as follows:
Remove the machine’s worktop by unscrewing the two rear
retaining screws, pull from the front and slide out the rear
slots, lifting the worktop.
Insert the machine after adjusting height and levelling with the
adjustable feet. When inserting the machine, ensure that the
water inlet and drain hoses are not kinked or squashed.
If the dishwasher is later used as a free-standing appliance,
the original worktop must be re-mounted.
The plinth on free-standing appliances is not adjustable.
Technical specifications
Dimensions
Width
60 cm
Height with worktop
Height without worktop
Max depth
85 cm
82 cm
61 cm
Electrical connection:
Voltage
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher’s door on the right.
Overall power
Fuse
Water supply connection:
Water supply pressure:
cold water
Maximum
Maximum
50 kPa (0.5 bar)
800 kPa (8 bar)
Capacity
12 place settings
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish
to purchase spare parts please contact your local Service
Force Centre by telephoning:
Customer Care
Department
08705 929929
For general enquiries concerning your Tricity Bendix appliance
or for further information on Tricity Bendix products please
contact our Customer Care Department by letter or telephone
at the address below.
Your telephone call will be automatically routed to the Service
Force centre covering your post code area.
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
Customer Care Department
Tricity Bendix
55-77 High Street
Slough
Before calling out an engineer, please ensure you read the
details under the heading Something not working.
Berkshire
SL1 1DZ
Tel: 08705 950950 ( )
*
When you contact the Service Force Centre you will need to
give the following details:
1. Your name, address and post code
2. Your telephone number
calls to this number may be recorded for training purposes
*
3. Clear and concise details of the fault
4. The model and serial number (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
For Customer Service in Ireland please contact us at the
address below:
Tricity Bendix
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0)1 4090752
Email: [email protected]
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Standard guarantee conditions
European Guarantee
We, Tricity Bendix, undertake that if within 12 months of the
date of purchase this Tricity Bendix appliance or any part
thereof is proved to be defective by reason only of faulty
workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or
carriage on condition that:
If you should move to another country within Europe then your
guarantee moves with you to your new home subject to the
following qualifications:
G The guarantee starts from the date you first purchased your
product.
G The guarantee is for the same period and to the same extent
for labour and parts as exists in the new country of use for
this brand or range of products.
G The appliance has been correctly installed and used only on
the electricity supply stated on the rating plate.
G The appliance has been used for normal domestic purposes
only, and in accordance with the manufacturer’s instructions.
G This guarantee relates to you and cannot be transferred to
another user.
G The appliance has not been serviced, maintained repaired,
taken apart or tampered with by any person not authorised
by us.
G Your new home is within the European Community (EC) or
European free Trade Area.
G The product is installed and used in accordance with our
instructions and is only used domestically, i.e. a normal
household.
G All service work under this guarantee must be undertaken by
a Tricity Bendix Service Force Centre.
G Any appliance or defective part replaced shall become the
Company’s property.
G The product is installed taking into account regulations in
your new country.
G This guarantee is in addition to your statutory and other legal
rights.
Before you move please contact your nearest Customer Care
centre, listed below, to give them details of your new home.
They will then ensure that the local service Organisation is
aware of your move and able to look after you and your
appliances.
Home visits are made between 8.30am and 5.30pm Monday
to Friday. Visits may be available outside these hours in which
case a premium will be charged.
France
Senlis
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800 117511
+46 (0) 20 78 77 50
+44 (0)1753 219898
+353 (0)1 4090752
Germany Nurnberg
Exclusions
This guarantee does not cover:
Italy
Pordenone
Stockholm
Slough
Sweden
UK
G Damage or calls resulting from transportation, improper use
or neglect, the replacement of any light bulbs or removable
parts of glass or plastic.
Ireland
Dublin
G Costs incurred for calls to put right an appliance which is
improperly installed or calls to appliances outside the United
Kingdom.
G Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
G Products of Tricity Bendix manufacture which are not
marketed by Tricity Bendix.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints for test centres
Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing
programmes" chart).
Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and
rinse aid respectively and using the test programme (see "Washing programmes" chart).
Load:
12 standard place settings
Rinse aid setting
Rinse aid dispenser (type A):
Rinse aid dispenser (type B):
position 4 (type III)
position 5 (type III)
Detergent dosage:
5 g + 25 g (type B)
Arrangement upper basket
Arrangement lower basket
Arrangement cutlery basket
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tricity Bendix, 55-77 High Street, Slough, Berkshire, SL1 1DZ
Customer care telephone number...
08705 950 950
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as
refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year
to a value of approx. 14 billion USD in more than 150 countries around the world.
152968 08/1
Subject to change without notice
UK
© Electrolux plc 2003
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction book
Dishwasher
Before use
Maintenance
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety instructions
2
3
3
What to do, when...
Service and spare parts
8
9
Disposal
Installation instructions
Water supply connections
Water outlet hose connection
Electrical connection
10
10
10
11
Economical and ecological dishwashing
Prior to using for the first time
The water softener
Setting the water softener
Filling with salt
Rinse aid
Use of detergent
3
3
3
3
4
5
Different kinds of detergent
6
Maintenance and cleaning
Cleaning the filters
Prolonged periods of non-operation
Frost precautions
7
7
7
7
7
Moving the machine
Safety instructions
It is most important that this instruction book should be retained with the appliance for future reference. Should the
appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that
the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the
relevant safety information.
This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the
appliance.
Installation
Your dishwasher in day-to-day use
G Check your dishwasher for any transport damage. Never
connect a damaged machine. If your dishwasher is
damaged, you should contact your supplier.
G Items that are contaminated by petrol, paint, steel or iron
debris, corrosive, acidic or alkaline chemicals must not be
washed in this dishwasher.
G For safety reasons it is dangerous to alter the specifications
G Under no circumstances should you open the door whilst
the appliance is in operation, especially during the washing
phase, hot water may escape. However, if the door is
opened, a safety device ensures that the machine stops.
or attempt to modify this product in any way.
G Any electrical and plumbing work required to install this
appliance should be carried out by a qualified and
competent person.
G Only use products (detergent, salt and rinse aid) specifically
designed for use in dishwashers.
G The appliance should not be connected to the electrical
supply by means of an extension cable.
G Long bladed knives stored in an upright position are a
potential hazard.
G Care must be taken to ensure that the appliance does not
stand on the electrical supply cable.
G Long and/or sharp items of cutlery such as carving knives
must be positioned horizontally in the upper basket.
G The sides of the dishwasher must never be drilled to
prevent damage to hydraulic components.
G When finishing loading or unloading close the door, as an
open door can be a hazard.
G Do not sit or stand on the open door.
Child safety
G Isolate the appliance from the power supply and turn off the
G This appliance is designed to be operated by adults.
water supply after use.
G Children should not be allowed to tamper with the controls
G This product should be serviced by an authorised service
or play with the product.
engineer, and only genuine spare parts should be used.
G Packaging parts may be dangerous for children, who could
even be suffocated! You should therefore keep all
packaging well away from children.
G Under no circumstances should you attempt to repair the
machine yourself. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning.
Contact your local consumer services department. Always
insist on genuine spare parts.
G The water in your dishwasher is not for drinking. Detergent
residues may still be present in your machine. Keep
children well away from your dishwasher when the door is
open.
G Keep all detergents in a safe place out of children's reach.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal
Economical and
ecological dishwashing
G Ensure that the water softener is correctly adjusted.
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with standard international
abbreviations:
G Do not pre-wash under running water.
>PE<
>PS<
for polyethylene, e.g. sheet wrapping material.
for polystyrene, e.g. padding material (always CFC-
free).
G Select the wash programme to suit the nature and degree of
the soiling on the dishes.
G Do not use more detergent, special salt and rinse aid than is
recommended in these operating instructions and by the
manufacturer of the respective product.
>POM< for polyoxymethylene, e.g. plastic clips.
Cardboard packaging is manufactured from recycled paper
and should be deposited in the waste paper collection for
recycling.
As and when you cease to use your dishwasher and withdraw
it from service, your should render it unserviceable before
having it disposed of.
Warning! Children at play could lock themselves in your
dishwasher or otherwise endanger their lives. Therefore cut off
the power supply cable and make the door closing device
unusable to prevent children from being trapped inside.
For the disposing of the appliance please take it to a recycling
centre or to your dealer who will, for a small contribution to the
costs, dispose it for you.
Prior to using for the first time
Before using your dishwasher for the first time:
Only for dishwasher models with salt refilling
indicator light:
1. Ensure that the electrical and water connections comply
If the water softener has been adjusted on level 1 and no salt
is being used, the salt refilling indicator light on the control
panel, will always remain illuminated when the machine is
switched on.
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with salt
Setting the water softener
5. Fill the rinse aid dispenser
1. Open the dishwasher door.
The water softener
2. Remove the lower basket from the dishwasher.
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
3. Turn the water hardness switch until the required level (see
table) corresponds with the marker .
4. Replace the lower basket.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, German
degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The dishwasher is factory set at position 2.
Water hardness
Water
hardness
setting
AA08
Use of
salt
°TH
°dH
PPM
french degrees
71 - 90
51 - 70
31 - 50
8 - 30
german degrees
parts per million
yes
yes
yes
yes
no
41 - 50
30 - 40
19 - 29
4 - 18
< 4
level 5
level 4
level 3
level 2
level 1
701 - 900
501 - 700
301 - 500
80 - 300
< 80
< 8
If your water is below level 1 it is already soft and therefore
there is no need to use salt. In this case adjust the water
softener on level 1 without using salt.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling with salt
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying.
Only use salt specifically designed for use in
dishwashers.
The dispenser, which is positioned inside the door, holds about
110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing
programmes, depending upon the dosage setting.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the complete
washing programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
Filling with rinse aid
(Rinse aid dispenser type A)
1. Open the container by pressing the release button (A).
corrosion.
2. Fill with rinse aid exactly up to the level indicator marked
"max".
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
SALE
T
ZOUT
SAL
SALZ
SEL
4. Replace the cap making
sure that there is no trace
of salt on the screw
BR07
BR14
Ensure that the lid is closed after every refill.
thread or on the gasket.
5. Screw on the cap tightly
turning it clockwise until it
stops with a click.
Adjusting the dose
SR14
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (position
1 minimum dosage, position 6 maximum dosage).
The salt container will require topping up periodically.
Increase the dose if there
are drops of water or lime
spots on the dishes after
washing.
According to the model of dishwasher, you are reminded
of this by:
A) The salt cap has a refill indicator window in the centre.
A green float is clearly visible when there is salt inside the
container and almost disappears when the salt has finished
reminding you to add salt.
The dose is factory set in
position 4.
Reduce it if there are sticky
whitish streaks on the
dishes.
BR09
Filling with rinse aid
SR22
(Rinse aid dispenser type B)
1. Open the container by turning the lid (A) anticlockwise.
B) A salt indicator light on the control panel will come on
when the salt has finished.
2. Fill with rinse aid exactly up to the level indicator marked
"max".
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been replenished,
assuming the dishwasher remains switched on. If you are
using salts that take longer to dissolve then this can take
longer. The function of the machine is not affected.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
BR01
BR13
Ensure the lid is closed after every refill.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the dose
Use of detergent
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (C)
(position 1 minimum dosage, position 6 maximum dosage).
Only use detergents specifically designed for use in
dishwashers.
We recommend the use of Finish detergents.
Increase the dose if there are drops of water or lime spots on
the dishes after washing.
Using no more then the correct amount of detergent
contributes to reducing pollution.
The dose is factory set in
position 5.
Prior to the start of a wash programme (not for the "Rinse and
Hold" programme). The detergent is released during the
washing phase.
Reduce it if there are sticky
whitish streaks on the dishes.
Please observe the manufacturer’s dosing and storage
recommendations as stated on the detergent packaging.
Fill with detergent
BR02
(Detergent dispenser type A)
1. If the lid is closed: press release button (1).
The lid springs open.
2. Fill the detergent dispenser (2) with detergent.
The marking indicates the dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent
Top up with rinse aid when:
1. The indicator (B) becomes clear,
DE19
DE22
3. All programmes with prewash need an additional detergent
dose (5/10 g) that must be placed in the prewash detergent
chamber (3). This detergent will take effect during the
prewash phase.
BR03
BR11
2. Only for dishwasher models with rinse aid indicator
light:
4. Close the lid and press until it locks in place.
When the rinse aid indicator light on the control panel
illuminates (when the machine is switched on).
Fill with detergent
(Detergent dispenser type B)
Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during the next
wash.
1. Open the dispenser by pulling the catch (D).
Only use branded rinse aid for dishwashers. Never fill the
rinse aid dispenser with any other substances (e.g.
dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
The lid springs open.
2. Fill the detergent dispenser with detergent.
The marking indicates the dosing levels:
Min = approximately 15 g of detergent
Max = approximately 30 g of detergent
3. Close the lid and press until it locks in place.
DE02
DE17
4. All programmes with prewash need an additional detergent
dose (5/10 g) that must be placed over the lid of the
dispenser. This detergent will take effect during the prewash
phase.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Different kinds of detergent
Detergent tablets
Use of "3 in 1" combi detergents
Detergent tablets of different brands dissolve at different
speeds. For this reason some detergent tablets cannot
dissolve and develop their full cleaning power during short
programmes. Therefore please use long programmes when
using detergent tablets, to ensure the complete removal of
detergent residuals.
Do not place the tablets in the tub or in the cutlery basket
as this will result in poorer wash results. The tablets
should be placed in the detergent dispenser.
General advice
These products are detergents with integrated and combined
detergent/rinse-aid and salt functions.
1. Before using these products you should first check that the
water hardness in your supply is compatible with the use of
these products as per the detergent manufacturers (on the
product packaging).
2. These products should be strictly used according to the
detergent manufacturers instructions.
3. If you encounter problems when using 3 in 1 products for
the first time then please contact the detergent
manufacturers care line (the telephone number is given on
the product packaging).
Concentrated detergent
Based on their chemical composition, dishwasher detergents
can be split into two basic types:
- conventional, alkaline detergents with caustic components.
- low alkaline concentrated detergents with natural enzymes.
Special advice
The use of 50°C washing programmes in conjunction with
concentrated detergents reduces pollution and is good for your
dishes; these wash programmes are specially matched to the
dirt-dissolving properties of the enzymes in the concentrated
detergent. For this reason 50°C wash programmes in which
concentrated detergents are used can achieve the same
results that can otherwise only be achieved using 65°C
programmes.
When using combination 3 in 1 products select the lowest
possible setting for water hardness.
If you decide to turn back to the use of the standard detergent
system we advise that you:
G Refill both the salt container and rinse aid dispenser.
G Switch the water hardness setting to the highest possible
position and run a normal washing programme without a
load.
G Readjust the water hardness setting again according to the
hardness of the water in your area.
Combi detergents
If you are using dishwasher detergent that includes the rinse
aid function, this must be placed in the detergent compartment.
In this case the rinse aid compartment must be empty, in order
to avoid a double dosage.
If in the rinse aid compartment there is still rinse aid you must
wait until it has finished before using these kind of detergents.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and cleaning
Clean the external surfaces of the machine and control panel
with a damp soft cloth. If necessary use only neutral
detergents. Never use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
7. Put the flat filter (D) back in the base of the washing
compartment.
8. Place the coarse/fine filter (A/B) in the microfilter and press
together.
Ensure that the seals around the door, the detergent and rinse
aid dispensers are cleaned regularly with a damp cloth.
9. Put the filter combination in place and lock by turning the
handle clockwise to the stop. During this process ensure
that the flat filter does not protrude above the base of the
washing compartment.
We recommend the use of Finish Dishwasher Cleaner every
3 months or run a 65°C wash programme without dishes using
detergent.
Regular use of Finish Dishwasher Cleaner cleans
inaccessible parts, eliminates unpleasant food odours and
helps prevent the build-up of limescale.
Under no circumstances may the dishwasher be used
without filters.
Incorrect repositioning and fitting of the filters will
produce poor washing results.
Cleaning the filters
NEVER try to remove the
upper spray arm.
The filters in the base of the washing compartment are to a
large extent self-cleaning. Nevertheless the filters should be
checked and cleaned from time to time. Dirty filters will
degrade the washing result.
If residues of soil have
clogged the holes in the
upper spray arm, remove
them with a toothpick.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a coarse/fine filter
(A/B), a microfilter (C) and a flat filter (D).
Some dishwasher models filter system comprises only a
coarse filter (A), a microfilter (C) and a flat filter (D).
MA33
Prolonged periods of non-operation
If you are not using the machine for any period of time you are
advised to:
1. Unplug the appliance and then turn off the water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of any
unpleasant smells.
4. Leave the inside of the machine clean.
MA35
MA32
Frost precautions
Avoid placing the machine in a location where the temperature
is below 0°C. If this is unavoidable, empty the machine, close
the appliance door, disconnect the water inlet pipe and empty
it.
3. Unlock the filter system using the handle on the microfilter
1
4
(C), turn the handle about / a turn anticlockwise and
remove.
Moving the machine
If you have to move the machine (moving house etc....):
1. Unplug it.
2. Turn the water tap off.
MA36
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
4. Take hold of the coarse/fine filter (A/B) by the handle with
the hole and remove from the microfilter (C).
5. Clean all filters thoroughly under running water.
6. Remove the flat filter (D) from the base of the washing
compartment and clean both faces thoroughly.
MA31
7
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do, when...
Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions
given here, without calling out an engineer.
...there are problems when operating the dishwasher
The dishwasher will not start or stops during operation. All push buttons are inoperative except for the On/Off push button. Press the
On/Off push button to switch the dishwasher off and carry out the following suggested corrective actions.
Malfunction
Possible cause
Solutions
The water tap is blocked or furred with
limescale.
Clean the water tap.
The machine does not fill with
water.
The water tap is turned off.
Turn the water tap on.
The filter (where present) in the threaded hose
fitting at the water inlet valve is blocked.
Clean the filter in the threaded hose
fitting.
The water inlet hose has not been correctly laid
or it is bent or squashed.
Check the water inlet hose connection.
The dishwasher will not drain.
The siphon is blocked.
Clean out the siphon.
The water drain hose has not been correctly laid Check the water drain hose connection.
or it is bent or squashed.
The dishwasher door has not been properly
closed.
Close the door.
The programme does not start
The main plug is not plugged in.
Insert the mains plug.
Replace the fuse.
The fuse has blown in the household fuse box.
If dishes are to be washed immediately,
cancel the delay start.
For dishwasher models with delay start
option:
Delay start has been selected.
There is a whistling noise during
washing
The whistling is not a cause for concern.
Use a different brand of detergent.
Once the checks have been carried out, press the On/Off push button, the programme will continue from the point in which it was
interrupted. If the malfunction reappears contact your local Service Force Centre.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
...the wash results are not satisfactory
The dishes are not clean
G The wrong washing programme has been selected.
G The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded.
G The spray arms do not rotate freely due to wrong arrangement of the load.
G The filters in the base of the washing compartment are dirty or incorrectly positioned.
G Too little or no detergent has been used.
G Where there are limescales deposits on the dishes; the salt container is empty or the wrong level of the water softener has been
selected.
G The drain hose connection is not correct.
G The salt container cap is not properly closed.
The dishes are wet and dull
G Rinse aid was not used.
G The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on glasses and dishes
G Decrease rinse aid dosing.
Water drops have dried onto glasses and dishes
G Increase rinse aid dosing.
G The detergent may be the cause. Contact the detergent manufacturer’s consumer care line.
If after all these checks, the problem persists, contact your
local Service Force Centre, quoting the model (Mod.), product
number (PNC) and serial number (S.N.).
This information can be found on the rating plate located on
the side of the dishwasher’s door (see picture).
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod. : . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . .
S.N. :. . . . . . . . . . . . . . . . . . .
RA08
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation instructions
Any electrical and/or plumbing work required to install
this appliance should be carried out by a qualified
electrician and/or plumber or competent person.
Water outlet hose connection
The end of the drain hose can be connected in the following
ways:
Remove all packaging before positioning the machine.
1. To the sink outlet spigot, securing it to the underside of the
work surface. This will prevent waste water from the sink
running into the machine.
If possible, position the machine next to a water tap and a
drain.
2. Hooked over the edge of the sink using the special curved
plastic guide provided (if provided with the machine).
Water supply connections
This dishwasher may be fed with either hot (max. 50°) or cold
water (See "Technical specifications" - Instruction book part 2).
Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled
crockery as it shortens the washing programmes a lot.
3. To a stand pipe provided with vent-hole, minimum internal
diameter 4 cm.
The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.
The drain hose can face either to the right or left of the
dishwasher
For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto either a 3/4"
inch gas thread spout or to a purpose made quick-coupling tap
such as the Press-block.
Ensure the hose is not bent or squashed as this could prevent
or slow down the discharge of water.
The sink plug must not be in place when the machine is
draining as this could cause the water to siphon back into the
machine.
The water pressure must be within the limits given in the
"Technical specifications". Your local Water Authority will
advise you on the average mains pressure in your area.
If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.
The locknut must be correctly fitted to avoid water leaks.
The water inlet hose must not be kinked, crushed, or entangled
when it is being connected up.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation by
means of the locknut. (Attention! NOT all models of
dishwashers have fill and drain hoses provided with locknut. In
this case, this kind of facility is not possible).
The locknut must be correctly fitted to avoid water leaks.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose.
CS18
Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided.
Do not use, for connection, old hoses which have been
used in another appliance.
The dishwasher is fitted with safety devices that prevent the
wash water returning into the drinking water system and
comply with the applicable plumbing regulations.
Attention!
Our appliances are supplied with a security device to protect
against the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated
this can prevent the correct draining of your dishwasher.
We advise you therefore to remove it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
This appliance must be earthed.
The manufacturer declines any responsibility should this
safety measure not be observed.
The appliance should not be connected to the electrical
supply by means of an extension cable.
If the plug that is fitted to your appliance is not suitable for the
socket, it must be cut off and the appropriate plug fitted.
Important
The wires on the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in the mains
lead of your appliance may not correspond with the markings
identifying the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter "E" or the earth
symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the plug
which is marked with the letter "L" or coloured red.
E
L
N
CE04
The plug moulded onto the lead incorporates a 13amp BSI362
fuse. Only ASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is lost. The
cover/carrier is indicated by the coloured insert at the base of
the plug.
A replacement cover/carrier must be obtained from your local
Service Force Centre.
To isolate the dishwasher from mains, remove the mains plug.
Important!
The plug must still be accessible after the appliance
has been installed.
In case that the electrical cable has to be replaced,
please contact your local Service Force Centre.
This appliance complies with the following E.E.C. Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
152971 08/2
Subject to change without notice
2 05/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|